sipura spa 3000 how to - bicom systems · to learn how to find out the sipura spa 3000 ip address...

(c) 2003-2010 Bicom Systems

Sipura SPA 3000 How To

All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, ormechanical, including photocopying, recording, taping, or information storage and retrieval systems - without thewritten permission of the publisher.

Products that are referred to in this document may be either trademarks and/or registered trademarks of therespective owners. The publisher and the author make no claim to these trademarks.

While every precaution has been taken in the preparation of this document, the publisher and the author assume noresponsibility for errors or omissions, or for damages resulting from the use of information contained in thisdocument or from the use of programs and source code that may accompany it. In no event shall the publisher andthe author be liable for any loss of profit or any other commercial damage caused or alleged to have been causeddirectly or indirectly by this document.

Printed: avgust 2010

Sipura SPA 3000 How To


PublisherSpecial thanks to:

Managing Editor

Technical Editors

Cover Designer

...

...

...

...

...

Production

...

Team Coordinator

...

Sipura SPA 3000 How ToI


Table of Contents

Foreword I

Part I Introduction 2

Part II Registering Sipura SPA 3000 4

................................................................................................................................... 41 Requirements

................................................................................................................................... 62 Manual Configuration

......................................................................................................................................................... 6UAD Settings

......................................................................................................................................................... 8Creating Extension

......................................................................................................................................................... 11Registering ATA

................................................................................................................................... 143 Auto Provisioning

......................................................................................................................................................... 14UAD Settings

......................................................................................................................................................... 16Creating Extension

......................................................................................................................................................... 18Registering ATA

......................................................................................................................................................... 21LAN And WAN IP Address

Part III Using the Sipura SPA 3000 as aSIP/PSTN gateway with PBXware 24

................................................................................................................................... 241 Create A New Provider In PBXware

................................................................................................................................... 282 Create A New Trunk

................................................................................................................................... 313 Create A DID For PSTN Line

................................................................................................................................... 334 Configuring Sipura SPA 3000

Part IV Glossary 40

Index 0

Foreword

...


I

Part

I

2Introduction


1 Introduction

Sipura SPA 3000How to use the Sipura SPA 3000 with PBXware

This "How to" is written as a general guide on how to use your Sipura SPA 3000 withPBXware using 2.0.13(GWg) Sipura SPA 3000 firmware. It covers the most common

tasks required to have your Sipura SPA 3000 working efficiently.

Part

II

4Registering Sipura SPA 3000


2 Registering Sipura SPA 3000- Requirements- Manual Configuration- Auto Provisioning

2.1 Requirements

1. Sipura SPA 3000 firmware.

- Make sure that the device is loaded with 2.0.13(GWg) firmware.

2. DHCP server.

- Fully configured and operational DHCP server.

3. Sipura SPA 3000 Dial Plan.

- Fully configured and operational DHCP server.

- The Sipura SPA 3000 "Dial Plan" field value needs to be changed using the webinterface.

STEP ONE: Sipura SPA 3000 Web Interface.

1. Open a new browser window and enter the IP address in order to access theSipura SPA 3000 administration interface.

Example: http://192.168.1.101

To learn how to find out the Sipura SPA 3000 IP Address go to chapter "RegisteringATA" "STEP ONE".

an example with IP address

2. Hit "Enter" on your keyboard.

STEP TWO: The Sipura SPA 3000 Dial Plan field value.

1. Click on "Admin Login".

5 Sipura SPA 3000 How To


2. Click on "advanced" link.

3. Click on "Line 1" link.

4. Navigate down to the "Dial Plan" group. Clear the "Dial Plan" field, then copy andpaste the following value.

(*x.|**x.|*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxx|xxxxxxxxxxxx.)

5. Click on the "Submit All Changes" button. The Sipura SPA 3000 will reboot for changesto take effect.



2.2 Manual Configuration

- UAD Settings- Creating Extension- Registering ATA

2.2.1 UAD Settings

STEP ONE: PBXware IP address.

1. Find out the IP address of the PBXware server.

STEP TWO: Login to PBXware.

1. Open a new browser window and enter the IP address to access the PBXwareadministration interface login screen.

Example: http://192.168.1.2



3. Login to PBXware with your e-mail address and password.

STEP THREE: UAD status.

http://192.168.1.2



1. Make sure the UAD is enabled. To check the UAD status, navigate to "Settings:UAD"and click on the "edit" icon corresponding to "Sipura SPA 3000".

2. Make sure "Status" is set to "active", "Auto provisioning" is set to "No", and "DHCP"is set to "Yes".



3. Click on the "Save" button to save changes.

2.2.2 Creating Extension

STEP ONE: Add Extension.

1. Navigate to "Extensions". Click on "Add Extension".

2. The standard options window (below) will be shown.

3. Select the Sipura SPA 3000 from the "UAD" select box.

4. Select Location: "Local" or "Remote".Note:



-"Local" is for all extensions registered on LAN.

-"Remote" is for all extensions registered from remote networks, WAN, Internet etc.

5. Click on the "Next" button.

STEP TWO: Extension values.

1. Enter values into the required field text boxes.

REQUIRED FIELDS:

Name:Enter a name for the extension being created. Example: John Smith. E-mail:Enter the e-mail address associated with this extension. This e-mail address willreceive all system notification messages. Example: [email protected].

an example with details filled in

2. Click on the "Save" button.

mailto:[email protected]




3. Click on the "Save & E-mail" button. Account details will be sent to the e-mail addressassociated with this extension.

OPTIONAL FIELDS:

Extension:An auto-generated extension number based on the next available sequentialnumber. An extension value can be changed. Example: 1000. Username:Username is auto generated/populated and cannot be changed since it allows thesystem to use this value for other important operations. Secret:A secret value associated with the UAD is auto-generated in order to allow the UADto successfully register with the system. The secret value can be changed. PIN:An auto-generated PIN will allow access to voicemail and online self care.



2.2.3 Registering ATA

STEP ONE: Electricity and Ethernet.

- Connect the other end of the cable to an analog telephone.

- Your Sipura SPA 3000 needs electricity, so plug the adapter into its jack andconnect it to the electricity network.

- Connect the ethernet port to a hub, router. or switch as access to LAN.



After successfully connecting your Sipura SPA 3000 to the electricity and data networks,it is time to register it to PBXware.

STEP TWO: Sipura SPA 3000 IP address.

Find out the IP address of your Sipura SPA 3000 connected to network.

1. Dial ****.

2. Dial 110#.

STEP THREE: Sipura SPA 3000 Web Interface.

1. Open a new browser window and enter the IP address in order to access theadministration interface.

Example: http://192.168.1.101



STEP FOUR: Configuring your Sipura SPA 3000.

1. Click on "Admin Login" .

2. Click on "Line 1" .

3. Enter the following details into their respective fields.

http://192.168.1.101



REQUIRED FIELDS:

Proxy IP address of the PBXware server. Example: 192.168.1.2

User IDPBXware extension number. Example: 1000.

PasswordThe Secret of the extension as received in the e-mail associated with this extension. Example: 3dX3r5


4. Navigate to the bottom of the page and click on the "Submit All Changes" button.The Sipura SPA 3000 will reboot for changes to take effect.

OPTIONAL FIELDS:

Display name Example: John Smith, Reception, Entrance Main, Agent One etc.

Auth ID Usually the same number as for the account.

Other fields Other "options" or "fields" should be left blank or as is by default, they are notimportant for registering your Sipura SPA 3000 to PBXware.

- Conclusion: If everything is done as above described, you should have successfullyregistered your Sipura SPA 3000 to PBXware. Dial *123 to verify registration.

- For further information, please contact the manufacturer or check their website www.sipura.com.



2.3 Auto Provisioning

- UAD Settings- Creating Extension- Registering ATA- LAN And WAN IP Address

2.3.1 UAD Settings

STEP ONE: PBXware IP address.

1. Find out the IP address of the PBXware server.

STEP TWO: Login into PBXware.

1. Open a new browser window and enter the IP address to access the PBXwareadministration interface login screen.

Example: http://192.168.1.2



3. Login to PBXware with your e-mail address and password.

http://192.168.1.2



STEP THREE: UAD status.

1. Make sure the UAD is enabled. To check the UAD status, navigate to "Settings:UAD"and click on the "edit" icon corresponding to "Sipura SPA 3000".

2. Make sure "Status" is set to "active", "Auto provisioning" is set to "No", and "DHCP"is set to "Yes".



3. Click on the "Save" button to save changes.

2.3.2 Creating Extension

STEP ONE: Add Extension.

1. Navigate to "Extensions". Click on "Add Extension".


3. Select the Sipura SPA 3000 from the "UAD" select box.

4. Select Location: "Local" or "Remote".



Note:

-"Local" is for all extensions registered on LAN.

-"Remote" is for all extensions registered from remote networks, WAN, Internet etc.


STEP TWO: Extension values.


REQUIRED FIELDS:

Name:Enter a name for the extension being created. Example: John Smith. E-mail:Enter the e-mail address associated with this extension. This e-mail address willreceive all system notification messages. Example: [email protected]

Auto provisioning:Set to "Yes".

MAC Address:Sipura SPA 3000 MAC address. Example: 001646f5f797

mailto:[email protected]






3. Click on the "Save & E-mail" button. Account details will be sent to the e-mail addressassociated with this extension.

OPTIONAL FIELDS:

Extension:An auto-generated extension number based on the next available sequentialnumber. An extension value can be changed. Example: 1000. Username:Username is auto generated/populated and cannot be changed since it allows thesystem to use this value for other important operations. Secret:A secret value associated with the UAD is auto-generated in order to allow the UADto successfully register with the system. The secret value can be changed. PIN:An auto-generated PIN will allow access to voicemail and online self care.

2.3.3 Registering ATA


- Insert a standard RJ-11 telephone cable into the "Phone 1" port.





- Connect the ethernet port to a hub, router or switch as to access LAN.

After successfully connecting your Sipura SPA 3000 to the electricity and data networks,it is time to register it to PBXware.

The "Profile Rule" field must be set with TFTP server value.





1. Dial ****.

2. Dial 110#.


1. Open a new browser window and enter the IP address in order to access the SipuraSPA 3000 administration interface.

Example: http://192.168.1.101



STEP FOUR: Configuring "Profile Rule".

1. Click on "Admin Login" link.


3. Click on "Provisioning" link.

http://192.168.1.101



4. Navigate down to "Profile Rule" field, it must be set with TFTP server value.

Example: 192.168.1.2/$MA.cfg

an example with details filed in

5. Navigate to the bottom of the page, click on the "Submit All Changes" button. TheSipura SPA 3000 will reboot for changes to take effect.

- Conclusion: If everything is done as above described, you should have successfullyregistered your Sipura SPA 3000 to PBXware. Dial *123 to verify registration.

- For further information, please contact the manufacturer or check their website www.sipura.com.

2.3.4 LAN And WAN IP Address

Make sure your "Auto Provisioning" "LAN" and "WAN" IP fields are set with correct IPaddress.

1. Navigate to "Settings:Servers", and click on the "edit" button corresponding to theserver.



2. Navigate down to "Auto Provisioning" group.

- LAN IP: Enter your PBXware local (LAN) IP address. Example: 192.168.1.2

- WAN IP: Enter your PBXware wide (WAN) IP address. Example: 89.146.131.130


3. Click on the "Save" button. You'll be prompted to click on the "OK" button to restartPBXware for changes to take effect.

Part

III

24 Using the Sipura SPA 3000 as a SIP/PSTN gateway with PBXware


3 Using the Sipura SPA 3000 as a SIP/PSTN gateway withPBXwareThe Sipura SPA 3000 is a small and inexpensive ATA and SIP/PSTN gateway. Withcareful configuration, it may be used in conjunction with PBXware in place of the DigiumZaptel interface cards. This can be of particular advantage in some implementationssince the Digium single-port X100P FXO cards for Asterisk cannot be used, for example,in the UK due to impedance mismatch, and the new TDM400P base price is more thandouble the cost of the Sipura unit even before adding the required FXO or FXS modules.

The only disadvantage is that for PBXware licensing, each Sipura SPA 3000 countsagainst the licensed number of VOIP trunks for the version of PBXware.

This how-to guide gives simple instructions on how to setup PBXware and the Sipura SPA3000 to work together. You must use a fixed IP address with the Sipura SPA 3000 towork correctly because of limitations of either PBXware or the Sipura SPA 3000 havingmutually exclusive authentication entities.

- Create A New Provider In PBXware- Create A New Trunk- Create A DID For PSTN Line- Configuring Sipura SPA 3000

3.1 Create A New Provider In PBXware

STEP ONE: Create a new provider.

1. Navigate to Settings:Providers. Click on "Add Custom Provider".





REQUIRED FIELDS:

Type:Select "VOIP".

Protocol:Select "SIP".

Name:Enter, for example: "Generic SIP/FXO Gateway".

General



User Type:Select "user and peer".

DTMF Mode:Select "rfc2833".

Country:Select, for example: "United Kingdom of Great Britain".

National dialing code:Enter "0".

International dialing code:Enter "00".

Network Related

Canreinvite:Select "No".

ChannelsEnsure that Channels are set to incoming and outgoing limits of 1 (it’s an analog lineand can only have one call at a time).

Incoming Limit:Enter "1".

Outgoing Limit:Enter "1".

AuthenticationHost and Peer host should be set to the IP address of the Sipura SPA 3000.

Host:IP address of the Sipura SPA 3000. Example: 192.168.1.111

Peer Host:IP address of the Sipura SPA 3000. Example: 192.168.1.111

Auth Method:Select "none".

Register:Select "Not required".

Insecure:Select "very".

Codecs



Disallow:Select "all".

Allow:Select "G.711 ulaw" and "G.711 alaw".


OPTIONAL FIELDS:Other "options" or "fields" should be left blank or as is by default.



3.2 Create A New Trunk

STEP ONE: Create a new trunk.

1. Navigate to "Trunks". Click on "Add Trunk".


3. Select the provider name "Generic SIP/FXO Gataway" from the "Provider" field.




5. Click on the "Advanced Options" button.


REQUIRED FIELDS:Name or Number:Enter a trunk name. Example: "Spa3000".

Emergency trunk:Select "No".

Username:PBXware needs something in these fields, so put anything, it will not be used.

Peer Username:The Sipura SPA 3000 needs something in these fields, so put anything, it will not beused.




OPTIONAL FIELDS:



Qualify:Enter "8000".

Other fields Other "options" or "fields" should be left blank or as is by default.

3.3 Create A DID For PSTN Line

STEP ONE: Create a DID for PSTN Line.

1. Navigate to "DID's".

2. Click on the "Add DID" button.



REQUIRED FIELDS:

Trunk:Select the trunks just created, "Spa3000".



DID/Channel (start):Enter your phone number as DID. Example: 07811112222

Destination:Direct it to Extension, IVR Queues, Voicemail etc. Example: Extension.

Value:Enter destination number. Example: 1000


Note: you MUST setup a DID because PBXware places each VOIP trunk into its owncontext. Therefore, when we get to the Sipura SPA 3000 configuration, if the dial planpoints to an extension, PBXware will respond with error 404 (Not Found) because theextensions are not in the same context as the trunk.



3.4 Configuring Sipura SPA 3000




- Connect the ethernet port to a hub, router, or switch to access LAN.



After successfully connecting your Sipura SPA 3000 to the electricity and data networks,it is time to register it to Sipura SPA 3000.



1. Dial ****.

2. Dial 110#.


1. Open a new browser window and enter the IP address in order to access theadministration interface.

Example: http://192.168.1.101



STEP FOUR: Configuring your Sipura SPA 3000.

1. Click on "Admin Login" link.


3. Click on "PSTN Line" link.

http://192.168.1.101



4. Navigate down to "Sip Settings" group.

SIP Port:

Enter 5060 into SIP Port field.

5. Navigate down to "Proxy and Registration" group.

Proxy:IP address of PBXware server. Example: 192.168.1.2

Register:Select "no".

Use Outbound Proxy:Select "no".

Use OP Proxy In Dialog:Select "no".

Make Call Without Reg:Select "yes".

Ans Call Without Reg:Select "yes".

DNS SRV Auto Prefix:Select "no".



6. Navigate down to "Dial Plan" group.

In the Dial Plans section, ensure that Dial Plan 1: has the following:Example: "(S0<:[email protected]:5060>)"

This format of the dial plan creates a “hotline” functionality between the PSTN andthe target SIP address. The Sipura SPA 3000 will immediately call the SIP addressupon receipt of an incoming call from the PSTN and will not answer the PSTN call untilthe SIP destination answers the call.

Leave the remaining dial plans as default (xx.)

7. Navigate down to "VoIP-To-PSTN Gateway Setup".

Voip-To-PSTN Gateway Enable:Select "yes".

Line 1 VoIP Caller DP:Select "none".

Line 1 Fallback DP:Select "none".

VoIP Caller Auth Method:Select "none".

One Stage Dialing:Select "yes".

VoIP Caller Default DP:Select "none".



8. Navigate down to "PSTN-To-Voip Gateway Setup".

PSTN-To-VoIP Gatewey Enable:Select "yes".

PSTN Ring Thru Line 1:Select "no".

PSTN CID For VoIP CID:Select "no".

PSTN Caller Default DP:Select "1".

PSTN Caller Auth Method:Select "none".

9. Navigate down to "FXO Timer Values (sec)".

VoIP Answer Delay:Enter "0".

PSTN Answer Delay:Enter "0".

PSTN-To-VoIP Call Max Dur:Enter "0".

10. Navigate down to "PSTN Disconnect Detection" and "International Control".



The rest of the configuration depends on the country’s telephone company analogPSTN configuration. The example shown here is for the UK. Refer to Sipura SPA3000 localization documentation for country-specific FXO configuration options.

11. Click on the "Submit All Changes" button. The Sipura SPA 3000 will reboot forchanges to take effect.

Part

IV

40Glossary


4 Glossary- DHCP = Dynamic Host Configuration Protocol (DHCP) is a communications protocolthat lets network administrators manage and automate the assignment of Internet.- HUB = A common connection point for devices in a network.- IP Address = Internet Protocol address.- Local = A local area network (LAN) is a computer network covering a local area, like ahome, office or small group of buildings such as a college.- LAN = Local Area Network.- PIN = Personal Identification Number.- Remote = Network devices that are managed or controlled from a network systemother than the system to which they are directly connected.- Router = A device that forwards data packets from one local area network (LAN) orwide area network (WAN) to another.- Switch = Network device that selects a path or circuit for sending a unit of data to itsnext destination.- UAD = User Agent Device.- VoiceMail = The electronic transmission of voice messages over the Internet. Themessages are stored on a computer until the recipient accesses and listens to them.- WAN = Wide Area Network.- Web Interface = A web interface is the system of controls with which the usercontrols a device.

...



sipura spa 3000 how to - bicom systems · to learn how to find out the sipura spa 3000 ip address...

Documents