single side formwork system - baili · single side formwork system 5 single side formworks system...

Single Side Formwork System

5

Single Side Formworks System is used in concrete structures like retaining walls, heavy curtains, etc.

According to the increasing fresh concrete pressure due to the height single side formwork systems are produced for different types of concrete.According to the concrete pressure, support distances and type of support is determined.BaiLi Single Side Formwork System offers great efficiency and excellent concrete finishing for structure in building construction and civil works.By using BaiLi Single Side Formwork System there is no chance to form honeycomb structures. This system consists of single sided wall panel and Single Sided Bracket, used for retaining wall.It can be used together with steel formwork system, as well as timber beam system up to the height of 6.0m.Single Sided Formwork System also used in the low-heat mass concrete field. E.g. in power-station construction where wall thickens are so great that the elongation of the tie rods that would take place means that it is no longer technically or economically viable to place through ties.


Introduction

◇

◇

◇

◇

◇

◇

◇

WALL FORMWORK SYSTEM

6

With stop ends for foundation slabWith slurry and sheet pile wallsForming single sided retaining wallsWhen casting against masonry wallsCIn underground-railway construction projects where a subsequent concrete split-duct is cast against a bored diaphragm wallFor supporting Starter-block formwork used in dam building

The Single Sided Bracket designed to be used through the formwork elements to tie them to the opposing formwork. This situation occurs for example:

Characteristics

◇

◇

◇

◇

◇

◇

The loads resulting from the pouring of the walls are transferred by the frames into the base structure through the cast in loop tie anchors at the front base of the formwork and through the compressive jacks at the rear of the single sided bracket.

Therefore, it is essential to determine whether the structure components, such as base slabs or foundations are capable to carry these loads. Moreover, the opposite side of the Single Side Wall Formwork (either existing structural parts or shoring) must be able to carry the concrete pressure as well. The arrangement of the loop ties and distance between the permanent anchors must be determined based on the calculated statically values

and the anchors must be positioned as accurately as possible prior to pouring the floor slab.

Please note that tie rods which are used for anchoring the Single Sided Bracket must never be welded or heated at all.


7

280

45¡ã

50

70

Wing Nut(D20)

Counterplate (D20)

Turnover Bolt(D20)

Connecting Bolt(D20)

Embeded Bolt(D20)

Steel Girder

Front adjusting seat

BaiLi Single Side Bracket is specially designed for single side wall.It is simple and convenient in construction, and can save labor and materials.Erection process is so simple as compare to other systems.Due to its simple assembly process there will be no need of any skill labor, it can be easily understood by unskilled labor also. BaiLi Single Side System consume less time.The height of concrete casting is adjustable and the maximum height is 8m.

Components

Formworm system

Waling-to-bracket holder

Back adjusting seat

Standard frame H=3600

Scaffold BracketHeighten frame H=500

Heighten frame H=1600



Front adjusting seat


8

Remarks Weight(Kg) Item No. Spec. & tech. parameter




Single Side Bracket

Single Side Bracket

Single Side Bracket

Single Side Bracket

Single Side Bracket

236.31

201.08

277.89

355.75

01160100

01160200

01160300

01160900

H=3600

Extension Part H=1600



Remarks Weight(Kg) Item No. Spec. & tech. parameterSingle Side Bracket

16.55 01160400 Extension Part H=500


9






Back Adjusting Seat

5.13 01160500

Front Adjusting Seat

Turnover Bolt

2.09

8.53

01160701

01160600

D20

Scaffold Bracket

Connecting Bolt

14.03

2.00

66000233

66000061 D20


10

Turnover Bolt

Wing Nut Counter Plate

Connecting Bolt

Embedded Bolt



Embedded Bolt

Wing Nut

2.41

0.67

01160702

66000062

D20

D20

Remarks Weight(Kg) Item No. Spec. & tech. parameterCounter Plate

1.26 66000073

Remarks Weight(Kg) Item No. Spec. & tech. parameterBottom Beam Anchor System

Anchor System for the First Pouring

2.070.671.262.002.41

0116070166005062660000736600506101160702

D20, L=700D20120x120D20D20 L=550

All the parts can be reused except embedded bolt.

single side formwork system - baili · single side formwork system 5 single side formworks system...

Documents