http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Food      Living       Outside        Play        Technology       Workshop

Simple Styrofoam Hot Wire Cutterby bulau65 on June 1, 2014

Table of Contents

Simple Styrofoam Hot Wire Cutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Intro:   Simple Styrofoam Hot Wire Cutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 1:   Materials and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Step 2:   Cut the frame parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 3:   Attach the feet and the arm to the base plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Step 4:   Attach the metal plate at the tip of the arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Step 5:   Bore a hole into the base plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Step 6:   Attach the spring and the underparts for the wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Step 7:   Tie the hot wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Step 8:   Time to close the electric circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Step 9:   Make sure the connections are tight and test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Step 10:   Safety concerns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Advertisements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Intro:  Simple Styrofoam Hot Wire CutterI made my own styrofoam hot wire cutter using just scrapped stuff. I haven't purchased anything specially for this build, as I had everything lying around my house, so Icannot give you any prices for the materials. The idea is that anyone could make their own styrofoam cutter, adapting the tutorial with whatever suitable items one canfind around. I really like the idea of upcycling, and I've tried to find a purpose for some items I was no longer using (old cd-player adapter, a metal plate from an oldcomputer video card, pieces of copper cable, etc).

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Step 1: Materials and ToolsYou will basically need to make a sturdy frame which will hold a tensed piece of metal wire. This wire needs to be connected to a power source.

tools:ruler, pencil, rubber eraser for measuring and markingvariable speed power drill for drilling and for driving screwsjigsawpliers

materials needed for the frame:one piece of particle board (you can also use MDF, plywood, metal, anything which has a flat surface and decent strength and durability). Mine was a discarded80cmx25cm, 20mm thick piece that I had from another project. A furniture workshop may give you scrap pieces for free or for a very small price. The arm of thecutter needs to withstand some considerable tension, so look for a material strong enough for that.screws. I needed two types of screws. Some shorter than the thickness of my particle board (1.5mm), and some twice the thickness of the board or longer (I hadsome 45mm ones).gluea spring to hold the cable tensioned. Bike brakes have a spring that's very good for our job. You can use a regular coil spring if it's strong enough.metal corner and flat plates. Computer cases have some slots on the rear panel which are covered with metal plates. They get to be replaced as you installvarious boards there. You can either use one of these cover metal plates, or detach one from an old video card, modem, lan card, etc.

cutting wireI've used a nichrome wire that I've streched from it's coil. I've run it a few times against a piece of wood to straighten it. These wires are easy to get where I livefrom shops that sell household items. Lots of people here build electric heaters with them. You can alternatively use a guitar string, though I think it won't be justas good. Nicrome has a higher resistance so it will get hotter. It also has a higher melting point than steel.Do not try to use copper or aluminum wire, as they have very low resistance and they will cause your other conductors to get hot as well, and you will alsodamage your power source!

power sourceAlthough you could make a foam cutter running with alternative current directly from your wall socket, it would be extremely dangerous to work with and you mayburn your house fuses. What you'll need is an AC/DC adapter capable of outputting at least 1 Ampere (1000mA), 2 or more Amps being preferable. I've found outthat voltage doesn't matter that much. Phone chargers are usually not strong enough for this purpose. You'll need to read the specs from your adapter. A laptopcharger should be good, but you may need to use a longer piece of wire or add some resistors on the circuit, because it may cause the wire to overheat. You mayalso not want to risk burning the charger of your running laptop. Some people have managed to adapt an old ATX power source to use for their styrofoam cutters.I've tried that, but the source got burned. You can also use batteries, but I find that a bit wasteful.What I'm using right now is an 1A 4.5V adapter from an old cd-player. I've measured the intensity of the electrical current when my foam cutter was running, and itwas somewhere between 1.5-2A, depending on how much wire length I was using. That means my adapter is used over it's designed capabilities and it may burnout unexpectedly from overheating. I try to switch it off whenever I'm not using the cutter, and so far it's running with no problems. It used to heat up much morewhen I was charging my cd-player, so I guess it will hold for the job.The safest thing would be to use a variable power supply (you can buy one online for about 25$). A variable power supply would offer the advantage of being ableto adjust the current, and thus the temperature of the wire. They also have fuses and protection circuits that would make your foam cutter safer to use.

electrical cables for connectionsYou need some thick wires to connect the power source to your cutting hot wire. If you use very thin wires, they will get hot as well and may burn out.

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Step 2: Cut the frame partsMark and cut the board into four pieces. One would be the base plate, one the arm, one would serve to attach the arm to the base. One narrow strip would be cut intosmaller bits serving as feet under the base plate. Try to make your cuts as straight and clean as possible, though some parts don't need a lot of accuracy.

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Image Notes1. arm to base connection2. base plate3. arm4. feet

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Step 3: Attach the feet and the arm to the base plateI've glued the feet on the base plate. I've attached the narrow piece of board to the base plate using screws. I've made some holes with a counter sink before driving thescrews, so that the heads would not stick out.

I've marked the position of the arm. Make sure it stays vertical and that it rests well on the ground. When driving screws into the edge of the board, you should alwayspre-drill a hole so you won't have the board splitting up. Mine split towards the corner so I've patched it up with another nut and bolt screw which holds it together. It'sprobably good to use it anyway, because particle board is quite brittle at the edges. I've added another screw diagonally on the opposite side (pre-drilling and using thecounter sink too).

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Image Notes1. Remember to pre-drill!

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Step 4: Attach the metal plate at the tip of the armUse short screws and have some pre-drilled holes for them. Make sure the tip of the plate sticks out a bit from the end of the arm.

Step 5: Bore a hole into the base plateUse a ruler to establish the point where the wire will have to go through the base plate. Make sure the ruler is vertical. I bored a 4mm hole.

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Step 6: Attach the spring and the underparts for the wireTurn the plate upside down. and put a corner plate above the hole. The wire will be ran through the hole on the corner plate, so try to position the plate so that the wirewould come at the center of the hole.

Mark the position of the holes for the metal plates. I used a flat metal plate under the spring to avoid having the spring scratching against the surface, but the spring canbe fixed directly on the board.

The string is fixed on the board with screws, but it should be easily taken out, so don't tighten the screws too much. In the end the spring will stay into place just becauseof the tension in the wire.

Step 7: Tie the hot wireFirst tie the upper part of the wire. Run the wire through the base plate and the metal corner plate and tie it to the spring, leaving just enough length on the wire so thatthe spring will stay tensed at all times. You can then put the spring back into it's place. It should be well bent under the tension of the wire.

I've used some pliers to tie the wire. It's good to have some spare wire prepared in case the wire brakes when doing the knot.

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Step 8: Time to close the electric circuitI had an universal adapter kit for my charger. I've chosen one tip that could be fastened to my frame with one small screw inside it's tip. This way, I could easily take outmy adapter, when storing my foam cutter. It also allows me to easily change to another power source, in case I find a better alternative.

I think this part can be improved a little with a more elegant solution. The cables could be connected to banana plugs for instance.

A simple lazy man's alternative would be to split the cable coming from the charger and just tie the two cables to the ends of the nichrome wire.

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Step 9: Make sure the connections are tight and testIt's good to leave some extra length to the upper cable, so it can slide up and down the nichrome wire. This varies the resistance of the cutting wire, regulating thetemperature. The shorter the wire, the higher the intensity of the current, and therefore the heat. If you need to get the wire really short in order to melt the foam, thatmeans your power source is not powerful enough, and you run the risk of burning it because a wire which is too short makes the current really high.

If you're an electrical geek, you can add a potentiometer on the circuit to regulate the current. If you use a variable power supply, then everything is even more simple.

You can now start to cut your pieces of foam and experiment with the temperature.

http://www.instructables.com/id/Simple-Styrofoam-Hot-Wire-Cutter/

Step 10: Safety concernsYou shouldn't leave the styrofoam cutter powered when you're not around.

If you're using less than 2 amps or 12 volts, you won't feel any electrical current if you touch the wire, but watch out as it can get really hot. The metal parts which are outof the circuit (the metal plate on the arm and the spring) will not be traversed by electricity, so they will not heat up.

You should not leave the styrofoam cutter at the reach of children.

Styrofoam cutting produces toxic gases. They can give you head aches and, when exposed to them on a regular basis, they can give you cancer. It's best to use thecutter outside, or near an open window. If you cut foam inside, the smell will be persistent for hours, so it's best not to cut foam in your bedroom/living room. Wearing amask is also highly recommended.

Related Instructables

Make AStyroFoamSculpting Toolby Creativeman

NiChrome HotWire Cutter forAcrylic byfozzy13

How To Make AHotwireCutter...Cheap!by Creativeman

no long build +no transformer= great hot wirefoam cutter(Photos) bytgferreira184

Chunky JigsawPuzzles byhive76

Hot Wire IceCutter by DIYHacks and HowTos

Advertisements

Comments

7 comments Add Comment

 HueZo says:  Oct 6, 2014. 10:45 AM  REPLYnice work!! thanks.

 rjkorn says:  Jun 17, 2014. 12:35 PM  REPLYI've wanted to build one of these for a while. so much nicer than a handheld bow. I even bought the nichrome wire already but seeing this gives me the pushto do it.

thanks!

 craftclarity says:  Jun 5, 2014. 10:15 AM  REPLYThis looks super-useful. I do some prototyping with foam (for composites) and this looks like it'd be a great way to save some time (and not create dust) onmy way to a form...

 bulau65 says:  Jun 1, 2014. 7:20 AM  REPLYEnglish is not my first language, so please correct me if you spot any mistakes.

 omnibot says:  Jun 2, 2014. 6:44 AM  REPLYNo errors spotted. Well done!

 wikkedspindl says:  Jun 1, 2014. 12:50 PM  REPLYCould you use an old toaster? I figure they are already built with proper resistors, power supply, and the heating element. Plus they are relatively cheap andaccessible. Just didn't know if that was a feasible build.I do love the instructable! I thought about just using blades was going to be the cheapest (but not very effective way). Thank you!

 bulau65 says:  Jun 1, 2014. 2:09 PM  REPLYToasters use alternative current. You could basically do the same thing a toaster does by connecting your wire directly to the main power line. Thedifference is that a toaster will have a much longer wire coiled inside so it will be able to dissipate a lot of heat.

I think one could make a foam cutter using the main AC power line, by using some resistors, or just some extra wire, coiled somewhere on the circuit,which will only consume some of the power. But in that case touching the wire would be a life hazard. High voltage would also require connections to bevery secure and cables attached very well. Such work should not be performed by anyone who's not an electrician.

To sum things up, using a toaster for cutting styrofoam wouldn't be a good idea.