sikky lexus is-f/350/250 sway bar installation instructions
TRANSCRIPT
![Page 1: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/1.jpg)
Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions
Included in your package:
-Sway Bar (1)
-Endlinks (2)
-Bushings (2)
Step 1. Remove all items from the box.
Step 2. To begin removal of the factory sway bar, loosen the lower
19mm rear shock bolts to release the pinch on the factory endlinks. Do
not remove the bolt.
![Page 2: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/2.jpg)
Step 3. Remove the lower sway bar 12mm link nuts.
![Page 3: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/3.jpg)
Step 4. Remove the 12mm sway bar retainer bolts.
Step 5. Pull the factory endlinks up and out of the control arm. Rotate
the bar and slide out towards the driver side.
![Page 4: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/4.jpg)
Step 6. Apply bushing grease inside the provided bushings.
![Page 5: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/5.jpg)
Step 7. Open the bushing where it is sliced and slide over the sway bar.
Position as shown.
![Page 6: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/6.jpg)
Step 8. Make sure the bottom of the bushing is the round side.
Step 9. Slide bar into place from the driver side to the passenger side.
Step 10. Reinstall 12mm sway bar retainer bolts- do not tighten.
![Page 7: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/7.jpg)
Step 11. After all bolts have been started make sure the bushing is
properly installed. It needs to be aligned and centered as shown.
![Page 8: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/8.jpg)
Step 12. Once the bushings are properly aligned, you can now tighten
the four 12mm bushing retainer bolts.
Step 13. Rotate the bar out of the way to make clearance for the sway
bar endlinks. Slide bottom of endlinks into place and align with hole.
![Page 9: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/9.jpg)
Step 14. Start the 12mm sway bar retainer bolts. Do not tighten.
![Page 10: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/10.jpg)
*NOTE: On the driver’s side make sure the ride level sensor is attached
like the factory setup.
Step 15. Install the upper sway bar link into the hole of your choice. The
correct order is- washer, sway bar, washer, and nut. Now hand tighten
the nut. Do not tighten the jam nuts located above and below the
endlink turn buckle, leaving free play adjustment.
![Page 11: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/11.jpg)
Step 16. Once the endlinks are in tighten the lower 12mm sway bar
retainer bolts.
Hand tighten
Do not tighten
jam nuts
![Page 12: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/12.jpg)
*Note: Make sure the ride level sensor bracket stays located in the back
hole.
Step 17. Tighten the 19mm lower shock bolts to factory specs.
![Page 13: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/13.jpg)
Step 18. Fully tighten down the endlink nut. The endlink bolt is 16mm
and the nut is 19mm.
![Page 14: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/14.jpg)
Instructions for Setting Zero Preload
Step 1: Remove both rear wheels
Step 2: Set jack stands under lowest knuckle points
Step 3: Lower vehicle till all weight is supported by the jack stands. The
suspension now has full load on it.
Step 4. The endlink turn buckle will have pressure on it. Turn it
clockwise and counter clockwise until the pressure is relieved.
![Page 15: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/15.jpg)
Step 5. Now that the turn buckle is free, twist is clockwise until it stops
and note the position. Then twist it counter clockwise until it stops and
note the position. Center the turn buckle in between the 2 noted
positions and you will be set at zero pre load.
Step 6. Using a 7/8” wrench hold the turn buckle in place while using a
19mm wrench to tighten both jam nuts. Tighten the nuts just so they
are snug, DO NOT OVER TIGHTEN.
![Page 16: Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions](https://reader031.vdocuments.us/reader031/viewer/2022012423/61783ccab8f777116d4c3306/html5/thumbnails/16.jpg)
-Now double check all bolts are tightened down to factory torque specs
- Road test
-Enjoy!