Muhammad Shehzad Hassan House#588, Bhutto Nagar Sahiwal, Pakistan

+923237591045

shaxinust@gmail.com

Career Objective

Pursue a career in a growing and dynamic firm, putting my theoretical knowledge into practical

form, thus rendering all possible services in my capacity to the firm.

Employment History

September, 2013 to

December,2014

Engineer-1 Architectural & Civil Engineering Services (Pvt.) Limited, RWP, Pakistan

Job Responsibilities:

Being Structural Engineer, analysis of structures, designing of structural

members, checking of design calculations and checking of structural drawings

were the major responsibilities assigned during the job. I used ETABS and SAP

for designing of frame structures and SAFE for designing of foundation

February, 2015 to October,2015

Structural Design Engineer PAK ELECTRON LIMITED, Lahore, Pakistan

Job Responsibilities:

Being the sole Structural Engineer, designing the civil works for substations,

designing of structural members, preparation and checking of design

calculations, preparing variation orders and Bar Bending Schedules, Rate

Analyses, inter department coordination and timely completion of projects were

the major responsibilities assigned during the job. Headed the whole

construction of a Gas Insulated Substation. I used manual methods for design of

structural members.

Projects as a Structural Design Engineer

PROJECT/

CLIENT

NAME

LOCATION

NUMBER

OF STORIES

STRUCTURE

TYPE

FOUNDATI

ON TYPE

ANALYSIS

DESIGN

CODE

Retrofitting of

FFBL

Buiiding

Rawalpindi

Nine (09) Wide Beam-

Slab system

Isolated and

combine

footing

Manual and using

SAP

ACI 318-05

&

UBC 97

MEPCO

Shah Sadar

Din

N/A

132 kv Air

Insulated

Substation

Pile and

Strip

Foundation

Manual

ACI 318-05

&

UBC 97

MEPCO

Mubarak Pur

N/A

132 kv Air

Insulated

Substation

Pile

Foundation

Manual

ACI 318-05

&

UBC 97

Defence Raya

& Golf

Countary

Club DHA

Lahore

3

132/11.5 kv

GAS Insulated

Substation

Isolated and

combined

Foundation

-

ACI 318-05

&

UBC 97

Academic Qualification

2009 –2013 B.E Civil Engineering, College of Civil Engineering, CGPA: 3.45/4.00

National University of Science and Technology, Pakistan

2007-2009 FSc Pre-Engineering, Divisional Public School & Inter Marks: 954/1100

College Sahiwal

2005-2007 SSC, Govt. Batala School, Sahiwal Marks: 752/850

2013-2015 MS Structural Engineering, National University of CGPA: 3.69/4

Science and Technology, Pakistan

(Thesis in Progress)

B.E TERM PROJECTS

Seepage Control Measures: Case study of Wolf Creek Dam

In this paper I discussed the seepage occurring through the wolf creek dam foundation and discussed the

efficiency of concrete cutoff wall upstream and downstream.

Structural & Architectural Design of multi-storey House

Modification in architectural design, Structural Load Calculation & their distribution, Reinforcement

Area, Spacing & cutoff Details, Structural design & drawings of beams, columns, slabs, footing, bar

bending schedule.

Final Year Project

Analysis of severely Deflected Waffle Slab on SAFE and it’s retrofitting

Being leader of my syndicate I analyzed a waffle slab spanning 85ft x 55ft which had lost its

serviceability because of excessive deflection. Roof deflection was determined manually, physically and

with the help of SAFE. After the analysis I proposed a new safe design of the same slab that was verified

on the software again.

MASTERS Thesis

Behavior of RC Wide BEAMS and Validation of Bernoulli Beam Theory.

In my Research I am validating “Bernoulli Beam Theory” for reinforced concrete wide beams. Such

beams, because of their dimensions behave differently as compared with normal dimensioned beams.

Eight RC wide beams were tested under four point bending method. Beams are 30 and 40 inches wide

with a constant depth of 10 inches and span of 12ft. There are 4 sets of beams each containing two similar

samples. Each set has different longitudinal reinforcement ratio. Casting and testing of beams has been

completed. Analysis of the results is in progress.

Designing Projects during Bachelor’s Degree

1. Design of one-way joist floor system

2. Design of one way slab floor system

3. Design of a small house

4. Design of a two way slab by direct design method

5. Design of a flat plate

6. Design of flat slab 7. Design of Cantilever retaining wall

Professional Software And Computer skills

Auto Cad, Xstabl, Geo Studio slope/w, MS Office, SAFE, SAP, ABAQUS,ANSYS

Distinction and Achievements 1 I got 2nd Position in final year project.

2 I got 4.00/4.00 GPA in my 8th semester.

3 I got academic distinction in two semesters on achieving more than 3.5 GPA

4 I got NUST merit scholarship in two semesters on obtaining more than 3.5 GPA.

5 Worked as Teaching Assistant with HOD Structural Engineering at National University of

Sciences and Technology and scored GPA of 3.5 above in all semesters during my masters.

6 Highest C.GPA amongst all students in Masters class.

Leadership Activities 1 Syndicate leader of final semester project

2 Syndicate leader of one month surveying projects carried out in Abbottabad,

Areas of Interest 1 Design of concrete and steel structures.

2 Seismic design of RC, Steel and reinforced masonry structures.

3 Research on seismic response analysis of RCC, steel and masonry structures.

4 Project Management and planning.

5 Geotechnical Engineering.

Professional Memberships

1. Member of Pakistan Engineering Council (PEC)

References Will be furnished upon request