Patented

SETUP AND TAKE-DOWN INSTRUCTIONSOF

15 FT. LED LIGHT STRAND CHRISTMAS TREE

Model No. MLT-15 , WLT-15

Uncommon USA, Inc.1146 North Main Street, Lombard, IL 60148

Tel: 800-419-5880 Fax: 630-268-9655 4

Christmas Tree Light KitUncommon USA, Inc. Setup Instructions

Package includes:1 15' LED light set (24 light strands)1 Multi-dia. center base ring support (in 2 sections)6 36" curved metal tubing6 • 36" straight center lower ring supports1 8" top star1 Power transformer1 Remote controller12 W' hex screws2 1" hex screws1 Allen wrench

6. Start to place the lower ring supports as illustrated in Fig. 3, connectthe inner end (inner end is the one that is threaded to receive the hexscrew) first using the W' hex screws as illustrated in Fig. 3a, then theouter end using the hex screws that are holding the ring together as illustrated in Fig. 3b

Setup Instructions:Note: Please keep all packing materials for re-packing.

1. Unpack all items in the box.

2. Lower the pole to the lowest position and remove the flags.

3. Remove any ornament that is on top of the pole.

4. To determine the pole diameter, simply test the center base ringsupport around the pole, and pull out any unfit inserts if needed.Note: This multi-diameter center base ring support fits poles ofeither 2Y.,",2Yz", 2%" or 3" in dia.

Place the center base ring support around the pole, use the 2 - 1" hexscrews as illustrated in Fig. 1Note: Do not tighten at this time, just tight enough to hold the ring

around the pole.

5. Lay the curved 36" round sections of metal tubing around the outerbase of the pole, connect the sections with the W' hex screws asillustrated in Fig. 2Note: Do not tighten the screws at this time. This will form the lower

outer ring.

Fig. 1

Fig. 2

Fig. 3

Fig.3a

Fig.3b

Page 1

Uncommon USA, Inc. Setup Instructions

8. As shown in Fig. 4a, connect the power cord of the 8" top star tothe power supply under the light kit top. Fig.4a

7. As shown in Fig. 4, place the top of the light kit onto the top of the flagpole,and then use the 8" top star to secure the light kit top by screwing the star tothe top of the flagpole.Note: 1. The flat side ofthe light kit top is the bottom. 2. To avoid breakingthe star you must screw the star in by turning the "STEM" only, not thestar.

NOTE:TEST THE LIGHTS BEFORE PUTTING THEM ON THE POLE. Fig. 4

Find the power cord of the light kit and connect it to the power transformer, then connect the transformerto a power outlet. After you test the lights, disconnect the transformer from the power outlet.

9. Unwrap the light strands from the plastic wrappersand set up the light kit as illustrated in Fig. 5 - 6.

Step 1Raise the first section of the pole.Then remove the first Velcro stripfrom each of the four groups of lightstrands.

Fig. 5

Step 2Raise the 2nd section of the pole.Then remove the 2nd Velcro stripfrom each of the four groups of lightstrands.

Step 3Remove the clips from thebottom plastic strap ONEAT A TIME and securethem to the metal baseouter ring.

Fig. 6

1146 North Main Street, Lombard, IL 60148800-419-5880 Fax 630-268-9655

Page 2

Uncommon USA, Inc.10. Secure the 24 light strands to the metal base outer ring as

shown in Fig. 7.

Fig. 7

11. Raise the pole to 20 feet as shown in Fig. 8, tighten the center ringsupport. Connect the power transformer to a power outlet. The powertransformer should be off the ground to avoid being covered by snow,ice or water. Power Transformer:

Input: 120VAC 60HzOutput: 24VAC 1000mA

12. Set flashing modes. As shown in Fig. 9, there are 8 modes to choose from,including steady lights or various flashing selections. #8 is a rotation of#lthrough #7. Point the remote controller to the sensor (as shown in Fig. 9a)atop the tree light kit and press the number to select your desired modeand enjoy the lights. Note: This tree light kit uses an infrared remotesystem. The remote unit must be pointed to the sensor without beingblocked by a wall, glass or other obstacles. It has a limited distanceof 30 ft. between the remote unit and the sensor.

Fig. 8

Point this end/ to the sensorPress to power on/off

the lights

RemoteNote:Do not operate this infra-red remote under sunlight.Sunlight interferes withinfrared.

Setup Instructions

Note: Follow the instructions on theback of the remote unit for batteryreplacement. Battery type: CR2025CR2032

Note: Be sure the sensors face out as shown in Fig. 9ato receive the remote control signal. Adjust the sensorunit if needed.

pelNT REMOTE TOSENSOR TO OPERATE($EMS(il\lOCAn;OATOI''lIlE rneturutt J(lT)

Fig. 9 ATTENTIONQPeRtitlOML AAW3E:/.IAX.lO'H,fltW~~liWl£lOSf1iSQl!Remove the battery

tab to activate the ""UGIIT," ".<u,remote controller ~:-a.1II!1

Attention:Remote controller

1. To prevent strands from getting tangled, each time you need to lower the pole to do any adjustments,you must strap the light strands 2 times with 6 strands in a group (four groups for a tree set) using theVelcro strips. Please refer to the details in "Take-down Instructions."

2. If you have a 25 ft. pole, you will not pull out the top section ofthe pole to set up this light set.3. It is normal that the power transformer turns warm when it is working.4. Raise the light kit high enough above the ground. Do not let water, snow, or ice cover the light kit base.

This will ensure the lights work properly, and will help the metal base be kept in good conditions.ImportantDo not let power transformer submerge or soak in water. Use only the power transformer included with thisproduct. Do not use any other transformers. Improper use of transformer may damage both the product and •the transformer, and may cause the risk of fire. Connect the power cord to the transformer, and then connectthe transformer to a power outlet.

ProductVVarrantyUncommon USA, Inc. offers a limited 90 day warranty against manufacturer defecus) from the date of purchasewhen this product is employed as stated in this instruction manual.

Model No. MLT-15 / WLT-15 Made in China Page 3

Step 3As illustrated in Fig. 3 and Fig. 3a,remove the clips from the outerbase ring and secure them to theplastic strap ONE AT A TIME(six strands in a group and fourgroups for a tree set.)

Uncommon USA, Inc.Take Down and Storage of Christmas Tree Kit.

Note: Before re-packing the light kit, be sure you have kept all the packing materials as instructed in the setupinstructions.

1. Disconnect the power cord.2. Loosen the center ring support. Do not take apart.

3. Follow step 1 - 3 to take down the light kit.Note: The Velcro strips are to position light strands to prevent them from getting tangled.

Step ILower the pole 1 section.Then strap the light strandsas illustrated in Fig. I (sixin a group, four groups fora tree set) using the firstVelcro strip. The first stripshould be about 5 ft. abovethe bottom.

Fig. 1

4. Lower the last section ofthe pole.As shown in Fig. 4, use the providedpacking plastic sheet to wrap eachgroup of light strands in 3 folds toprevent the light strands from gettingtangled.

Fig. 4

Step 2Lower the next section of the pole.Then strap the same groups of lightstrands using the 2nd Velcro stripabout 5 ft. above the last one asillustrated in Fig. 2.

Fig. 2 Fig.3a

5. As shown in Fig. 5, disconnect the powercord of the top star from the light kit top.Then remove both the top star and the lightkit from the pole.

Fig. 5

Model No. MLT-IS,WLT-IS Made in China

Uncommon USA, Inc. Take-Down Instructions

6. Option 1:If your pole can be removed from the ground sleeve, lift the pole out of the sleeve and out of the center ringsupport. Then hang the entire tree kit base on the wall of your garage or other storage area, and re-pack therest of the light kit in the original packaging box.

Option 2:You may take apart the entire tree kit base. Then re-pack the light kit in the original packaging box as shownin Fig. 6.

Fig. 6

7. Replace the pole in the sleeve and display your flags.

Trouble-shootingClear light cap

<,ProblemThere are some lights of the tree kit that do not turn on.CauseThe clear light cap is loose.SolutionThe clear light cap is designed to secure the LED bulb in place to connect with the wires. Tighten the clear lightcap by turning it clockwise. There are eight lights in a group. If one of them has lost contact with the wire, theother seven lights will not turn on either. Once the loose cap is identified and tightened, all eight lights will turn on.

Maintain and Care for the LED Light Strand Christmas TreeYou should maintain and care for the tree light kit in the following areas before storage.1. Clean and wipe all the metal parts. Use rust removal product (not included) such as WD-40 to clean any rusty• spots if there is any when powder coating is damaged. (Note: Follow the rust removal product instructionswhen using it.)

2. Repaint any spots where the paint on the metal part is damaged. (Note: Paint not included)3. Clean and wipe the light strands and all other parts. (Important: Do not let any part of this product submerge

or soak in water.)4. Be sure all parts are dry before storage.

1146 North Main Street, Lombard, IL 60148Page 5