servos
DESCRIPTION
Servos. Servos are everywhere. System to be controlled. Error signal. Sensor. Correction. Diff amp. Integrator. Transducer. Reference. Elements of servo. System -- to be controlled Sensor or detector -- measure quantity to be controlled Reference -- desired system output - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/1.jpg)
Servos
Servos are everywhere
![Page 2: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/2.jpg)
Elements of servo• System -- to be controlled• Sensor or detector -- measure quantity to be controlled• Reference -- desired system output• Diff amp -- compare sensed signal to reference• Error signal -- produced by diff amp
– = voltage proportional to system error• Integrator -- integrates error to give correction signal• Correction signal -- will be used to modify system and correct output• Tranducer -- converts correction voltage into action to control system
System to be controlled Sensor
Reference
Diffamp
Integrator
Transducer
Errorsignal Correction
![Page 3: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/3.jpg)
Example: Stabilize laser intensity• System is laser source plus AOM to deflect some (most) of laser power• Sensor is photodiode w/ preamp
– converts optical power to voltage (Volts/Watt opt)• Reference is stable voltage
– can be ac voltage -- ex: quiet amplitude modulation is desired• Transducer is RF driver to AOM
– converts voltage into RF power (Watts RF /Volt)
• System converts RF power to optical power (Watts opt / Watts RF)• Overall units of sensor, transducer, system cancel
Photodiode & preamp
Stablevoltage
Diffamp
Integrator
RF driver
Errorsignal Correction AOM Laser
System to be controlledLaserbeam
RF signal
![Page 4: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/4.jpg)
Servos and noise Frequency dependence of noise• Low frequency ~ 1 / f
– example: temperature (0.1 Hz) , pressure (1 Hz), acoustics (10 -- 100 Hz)• High frequency ~ constant = white noise
– example: shot noise, Johnson noise, spontaneous emission noise• Servo must compensate noise spectrum
– integrator– servo bandwidth out into white noise region
log(Vnoise)
log(f )
Noise amplitude
1/f noise
0
White noise
0.1 1 10 100 1kHz
log(gain)
log(f )
Desired servo gain
1/f noise
0
Unity gain
0.1 1 10 100 1kHz
![Page 5: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/5.jpg)
Servo stability• Real servo will have second pole eventually
– 12 dB/octave rolloff– converts negative feedback to positive feedback– causes oscillations, noise, instability
• Must have closed loop unity gain point before second pole• Real servo also has finite dc gain -- like op amp
log(Vout/Vin)
log(f )
Unity gain
Gain response
Max gain
0
Single pole6 dB
Double pole12 dB
Phaseshift
log(f )Phase response
-90 degrees
0 degrees
-180 degrees
![Page 6: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/6.jpg)
Closed loop response• Closed-loop gain and phase depend on all parts of servo• Closed loop gain is product of all gains
– Includes sensor and transducer – Recall product of gain units must cancel
• Closed loop phase is sum of all phases• Chain is as strong as weakest link
Shunted integrator Integrator w/lead
Effective “servo”
=log(gain)
log(f )
Unity gain
Single pole6 dB
0
Double pole12 dB
![Page 7: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/7.jpg)
Laser intensity noise• Laser intensity noise
– due to mode competition, power supply noise, resonator acoustics
– can also pass laser beam through spatial filter, fiber, etc before using
• May also want controlled modulation– ultra-quiet intensity modulation
Acoustic noise
Laser
Electronic noise
Spatial filter
![Page 8: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/8.jpg)
AOM = acousto optic modulator• AOM = acousto optic modulator (or deflector)• RF signal converted to sound waves in crystal
– Use fast piezo-electric transducer like Li NbO3
• Sound waves are collimated to form grating• Bragg scatter from grating gives deflected beam
– can separate from original• Problem with AOM -- weak link• Sound takes time to travel from transducer to laser beam
– Time delay: tD = l / v -- acts like multi-pole rolloff – (phase shift increases with frequency)
AOM crystal/glass
RF signal~ 1 Watt40 MHz
Sound transducerex: LiNbO3
Sound absorber(suppress reflections)
Refractive indexvariations due to sound waves
Input laser beam
Undeflected beam
Deflected beam
Aperture
l
![Page 9: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/9.jpg)
Photodiode with pre-amplifier• Photodiode like current source but with capacitor• Input capacitor causes op amp gain to diverge at high freq.
– Amplifies high freq noise– Oscillation
• Solution:– Shunt capacitor in feedback
Photo-diode amplifier
-
+
Vout
Rf
If
Ipd
Vbias
light
Photo-diodeequiv. circuit
Ipd
Cpd
Rpd
Shuntcapacitor
Cs
log(
Vou
t/Iin)
log(f )
Gain response
Unshunted
Shunted
![Page 10: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/10.jpg)
Servo design procedure• Measure gain and phase response of photodiode/preamp
– use LED driven with signal generator
• Measure response of AOM– use photodiode (PD) -- correct for PD response
• Design integrator to compensate for first pole• Gain control to set max gain w/o oscillation ??
– variable resistor at integrator input
• Sign of correction signal– each op amp reverses sign – overall servo must be negative feedback– sign change in transducers unknown until measured
• may have to add op amp• Use undeflected beam from AOM ?
– More laser power
![Page 11: Servos](https://reader036.vdocuments.us/reader036/viewer/2022072014/56812e14550346895d937ff2/html5/thumbnails/11.jpg)
Measure servo performance• Insert noise using transducer
• Summing junction– extra op amp ??
• Measure frequency response, phase delay– both error and correction signals
Photodiode & preamp
Stablevoltage
Diffamp
Integrator
RF driver
Errorsignal
Correction AOM Laser
System to be controlledLaserbeam
RF signal
Summing
Add error
Oscilloscope