service manual - repeater...
TRANSCRIPT
SERVICE MANUAL
COPYRIGHT © 2017 JVC KENWOOD Corporation No.RA054<Rev.001>2017/6
B5B-7268-00
VHF DIGITAL TRANSCEIVER, UHF DIGITAL TRANSCEIVERRA054<Rev.001>20176SERVICE MANUALB5B-7268-00
NX-3720H(G), NX-3720H, NX-3720(G), NX-3720, NX-3820H(G), NX-3820H, NX-3820(G), NX-3820
COPYRIGHT © 2017 JVC KENWOOD Corporation
TABLE OF CONTENTS1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-72 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-73 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-304 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-335 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-152
This product complies with the RoHS directive for the European market. This product uses Lead Free solder.
1-2 (No.RA054<Rev.001>)
Document CopyrightsCopyright 2017 by JVC KENWOOD Corporation. All rights reserved.No part of this manual may be reproduced, translated, distributed, or transmitted in any form or by any means, electronic,mechanical, photocopying, recording, or otherwise, for any purpose without the prior written permission of JVC KENWOODCorporation.
DisclaimerWhile every precaution has been taken in the preparation of this manual, JVC KENWOOD Corporation assumes no responsibilityfor errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. JVC KENWOOD Corporation reserves the right to make changes to any products herein at any time for improvement purposes.
Firmware CopyrightsThe title to and ownership of copyrights for firmware embedded in KENWOOD product memories are reserved for JVC KENWOODCorporation. Any modifying, reverse engineering, copy, reproducing or disclosing on an Internet website of the firmware is strictlyprohibited without prior written consent of JVC KENWOOD Corporation. Furthermore, any reselling, assigning or transferring of thefirmware is also strictly prohibited without embedding the firmware in KENWOOD product memories.
Transceivers containing AMBE+2 Vocoder:The AMBE+2 voice coding technology is embedded in the firmware under the license of Digital Voice Systems, Inc.
CopyrightsThe Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners.
NOTE• This equipment should be serviced by only qualified technicians.• Danger of explosion if the battery is incorrectly replaced; replace only with the same type.• To dispose of batteries, be sure to comply with the laws and regulations in your country or region.
TM
TM
(No.RA054<Rev.001>)1-3
SPECIFICATIONNX-3720H(G)/3720H(K TYPE)
*1 25 and 30 kHz are not included in the models sold in the USA or US territories.Analog measurements made per TIA603. Specifications are measured according to applicable standards.JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation.
GENERAL
Frequency Range 136~174 MHz
Max. Channels per Radio Up to 1000 channels with option
Number of Channels 512
Number of Zones 128
Channel Spacing Analog 12.5/15/25*1/30*1 kHz
Digital 6.25 /12.5 kHz
Operating Voltage 13.6V DC ±15%
Operating Temperature Range -22°F to +140°F (-30°C to +60°C)
Frequency Stability ±1.0 ppm
Dimensions (W x H x D) (Projections not included)
Radio with Control Head 6.30 x 1.69 x 6.30 in. (160 x 43 x 160 mm)
Weight (net) Radio with Control Head 2.65 lbs (1.2 kg)
RECEIVER
Sensitivity NXDN 6.25kHz Digital (3%BER) 0.20 μV
NXDN 12.5kHz Digital (3%BER) 0.25μV
DMR 12.5 kHz Digital (5% BER) 0.30μV
DMR 12.5 kHz Digital (1% BER) 0.45μV
Analog (12dB SINAD) 0.25μV
Selectivity Analog @ 12.5kHz 70dB
Analog @ 25kHz 80dB
Intermodulation Analog 70dB
Spurious Rejection Analog 80dB
Audio Distortion 2%
Audio Output 4W / 4ohm
TRANSMITTER
RF Power Output (H / M / L) 50W/30W/5W
Spurious Emission -73dB
FM Hum & Noise Analog @ 25 kHz 45dB
Analog @ 12.5kHz 40dB
Modulation Distortion 2%
Emission Designator 16K0F3E*1, 11K0F3E, 8K30F1E, 8K30F1D, 8K30F7W,4K00F1E, 4K00F1D, 4K00F7W, 7K60FXE, 7K60FXD,4K00F2D
1-4 (No.RA054<Rev.001>)
SPECIFICATIONNX-3720(G)/3720(E TYPE)
Analog measurements made per TIA603. Specifications are measured according to applicable standards.JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation.
GENERAL
Frequency Range 136~174 MHz
Max. Channels per Radio Up to 1000 channels with option
Number of Channels 512
Number of Zones 128
Channel Spacing Analog 12.5 / 20 / 25 kHz
Digital 6.25 /12.5 kHz
Operating Voltage 13.2V DC (10.8~15.6 V DC)
Operating Temperature Range -30°C to +60°C
Frequency Stability ±1.0 ppm
Dimensions (W x H x D) (Projections not included)
Radio with Control Head 160 x 43 x 160 mm
Weight (net) Radio with Control Head 1.2 kg
RECEIVER
Sensitivity NXDN 3 % BER (6.25 kHz/12.5 kHz) 0.20 μV / 0.28 μV
NXDN 1 % BER (6.25 kHz/12.5 kHz) -5.0 dBμV (0.28μV) / -2 dBμV (0.40μV)
DMR 12.5 kHz Digital (5 % BER) -4.5 dBμV (0.30μV)
DMR 12.5 kHz Digital (1 % BER) -2 dBμV (0.40μV)
Analog, EIA 12 dB SINAD (12.5/20&25 kHz) 0.25 μV
Analog, EN 20 dB SINAD (12.5/20&25 kHz) -1 dBμV (0.45 μV) / -3 dBμV (0.35 μV)
Selectivity Analog @ 12.5kHz 70dB
Analog @ 20kHz 78dB
Analog @ 25kHz 80dB
Intermodulation Analog 70dB
Spurious Rejection Analog 80dB
Audio Distortion 2%
Audio Output 4W / 4ohm
TRANSMITTER
RF Power Output (H / L) 25W/5W
Spurious Emission -36dBm 1GHz, -30dBm>1GHz
FM Hum & Noise Analog @ 25 kHz 50dB
Analog @ 20kHz 50dB
Analog @ 12.5kHz 45dB
Modulation Distortion 2%
Emission Designator 16K0F3E, 14K0F2D, 14K0F3E, 12K0F2D, 8K50F3E,7K50F2D, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E,4K00F1D, 4K00F7W, 7K60FXE, 7K60FXD, 4K00F2D
(No.RA054<Rev.001>)1-5
SPECIFICATIONNX-3820H(G)/3820H(K,K2 TYPE)
*1 25 kHz are not included in the models sold in the USA or US territories.Analog measurements made per TIA603. Specifications are measured according to applicable standards.JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation.
GENERAL
Frequency Range K 450~520MHz
K2 400~470MHz
Max. Channels per Radio Up to 1000 channels with option
Number of Channels 512
Number of Zones 128
Channel Spacing Analog 12.5/ 25*1 kHz
Digital 6.25 /12.5 kHz
Operating Voltage 13.6V DC ±15%
Operating Temperature Range -22°F to +140°F (-30°C to +60°C)
Frequency Stability ±1.0 ppm
Dimensions (W x H x D) (Projections not included)
Radio with Control Head 6.30 x 1.69 x 6.30 in. (160 x 43 x 160 mm)
Weight (net) Radio with Control Head 2.65 lbs (1.2 kg)
RECEIVER
Sensitivity NXDN 6.25kHz Digital (3%BER) 0.20 μV
NXDN 12.5kHz Digital (3%BER) 0.25μV
DMR 12.5 kHz Digital (5% BER) 0.30μV
DMR 12.5 kHz Digital (1% BER) 0.45μV
Analog (12dB SINAD) 0.25μV
Selectivity Analog @ 12.5kHz 70dB
Analog @ 25kHz 80dB
Intermodulation Analog 70dB
Spurious Rejection Analog 80dB
Audio Distortion 2%
Audio Output 4W / 4ohm
TRANSMITTER
RF Power Output (H / M / L) 45W/30W/5W
Spurious Emission -75dB
FM Hum & Noise Analog @ 25 kHz 45dB
Analog @ 12.5kHz 40dB
Modulation Distortion 2%
Emission Designator 16K0F3E*1, 11K0F3E, 8K30F1E, 8K30F1D, 8K30F7W,4K00F1E, 4K00F1D, 4K00F7W, 7K60FXE, 7K60FXD,4K00F2D
1-6 (No.RA054<Rev.001>)
SPECIFICATIONNX-3820(G)/3820(E TYPE)
Analog measurements made per TIA603. Specifications are measured according to applicable standards.JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation.
GENERAL
Frequency Range 400~470MHz
Max. Channels per Radio Up to 1000 channels with option
Number of Channels 512
Number of Zones 128
Channel Spacing Analog 12.5 / 20 / 25 kHz
Digital 6.25 /12.5 kHz
Operating Voltage 13.2V DC (10.8~15.6 V DC)
Operating Temperature Range -30°C to +60°C
Frequency Stability ±1.0 ppm
Dimensions (W x H x D) (Projections not included)
Radio with Control Head 160 x 43 x 160 mm
Weight (net) Radio with Control Head 1.2 kg
RECEIVER
Sensitivity NXDN 3 % BER (6.25 kHz/12.5 kHz) 0.20 μV / 0.28 μV
NXDN 1 % BER (6.25 kHz/12.5 kHz) -5.0 dBμV (0.28μV) / -2 dBμV (0.40μV)
DMR 12.5 kHz Digital (5 % BER) -4.5 dBμV (0.30μV)
DMR 12.5 kHz Digital (1 % BER) -2 dBμV (0.40μV)
Analog, EIA 12 dB SINAD (12.5/20&25 kHz) 0.25 μV
Analog, EN 20 dB SINAD (12.5/20&25 kHz) -1 dBμV (0.45 μV) / -3 dBμV (0.35 μV)
Selectivity Analog @ 12.5kHz 68dB
Analog @ 20kHz 76dB
Analog @ 25kHz 78dB
Intermodulation Analog 70dB
Spurious Rejection Analog 80dB
Audio Distortion 2%
Audio Output 4W / 4ohm
TRANSMITTER
RF Power Output (H / L) 25W/5W
Spurious Emission -36dBm 1GHz, -30dBm>1GHz
FM Hum & Noise Analog @ 25 kHz 50dB
Analog @ 20kHz 50dB
Analog @ 12.5kHz 45dB
Modulation Distortion 2%
Emission Designator 16K0F3E, 14K0F2D, 14K0F3E, 12K0F2D, 8K50F3E,7K50F2D, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E,4K00F1D, 4K00F7W, 7K60FXE, 7K60FXD, 4K00F2D
(No.RA054<Rev.001>)1-7
SECTION 1PRECAUTION
This service manual does not describe PRECAUTION.
SECTION 2SPECIFIC SERVICE INSTRUCTIONS
2.1 SYSTEM SET-UP
Merchandise received
Choose the type of transceiver
KRA-40 GPS active antenna
A personal computer, programming interface (KPG-46U/46X),
and FPU (programming software) are required for programming.
KCT-60Connection cable
KCT-36
Extension cable
KES-5
External speakerIgnition sense cable
KCT-18KES-3
External speaker
(Option)
(Option)
(Option) (Option)(Option)
Delivery
Transceiver programming
(Option: NX-3720H(G), NX-3720(G), NX-3820H(G), NX-3820(G) only)
*Only when required.
Frequency range (MHz) RF powerType
TX/RX 136~174
TX/RX 136~174
TX/RX 136~174
25W
50W
50W
NX-3720(G) E
NX-3720H(G) K
NX-3820H(G) K
NX-3820H(G) K2
NX-3720H K
NX-3820H K
NX-3820H K2
TX/RX 450~520
TX/RX 136~174
TX/RX 450~520
45W
25W
45W
NX-3720 E
TX/RX 400~470
TX/RX 400~470
TX/RX 400~470
25W
45W
45W
NX-3820(G) E
TX/RX 400~470 25WNX-3820 E
Yes
No
Yes
GPS antenna
Yes
No
No
Yes
No
Yes
No
1-8 (No.RA054<Rev.001>)
2.2 REALIGNMENT
2.2.1 Modes
*1:In order to use the Front panel programming mode, it isnecessary to purchase the "Front panel program" featureoption.
2.2.2 How to Enter Each Mode
*2 There is the two or three as how to enter.
2.2.3 Panel Test ModeSetting method refer to ADJUSTMENT.
2.2.4 Panel Tuning ModeSetting method refer to ADJUSTMENT.
Mode Function
User mode For normal use.
Panel test mode Used by the dealer to check thefundamental characteristics.
Panel tuning mode Used by the dealer to tune the transceiver.
PC mode Used for communication between thetransceiver and PC.
Data programming mode
Used to read and write frequency data andother features to and from the transceiver.
PC test mode Used to check the transceiver using thePC. This feature is included in the FPU.
Firmware programming mode
Used when changing the main program ofthe flash memory.
Clone mode Used to transfer programming data fromone transceiver to another.
Front panel programming mode
Frequency, signaling and features write tothe transceiver.
Transceiver information mode
Used to confirm the transceiver firmwareversion, Encryption Library version.
User mode
Data programming mode
PC tuning mode
Transceiver information mode
PC mode
Panel tuning modePanel test mode
Firmware programming mode
Clone mode
Front panel programming mode*1
PC test mode
Mode Operation
User mode Power ON
Panel test mode*2 • [ ] + Power ON
• [ ] + Power ONSelect the “Panel Test” using the [] / [] button.Press the [ ] button.
PC mode Received commands from PC
Panel tuning mode [Panel test mode] + [ ]
Firmware programming mode*2
• [ (AUX)] + Power ON
• [ ] + Power ONSelect the “Firmware Prog” using the [] / [] button.Press the [ ] button.
• If Write is performed by KFL, Firmware programming mode will start automatically.
Clone mode*2 • [ ] + Power ON
• [ ] + Power ONSelect the “Clone” using the [] / [] button.Press the [ ] button.
Front panel programming mode*2
• Press the PF button to which Front panel programming mode is set during the user mode.
• Press the [ ] button and enter the Menu mode.
Select the any icon assigned the Front panel programming mode using the [] / [] button.Press [ ] button.Select the “Panel Program” using the [] / [] button.Press the [ ] button.
Transceiver information mode*2
• [+] + Power ON
• [ ] + Power ONSelect the “Transceiver Info” using the [] / [] button.Press the [ ] button.
(No.RA054<Rev.001>)1-9
2.2.5 PC Mode
2.2.5.1 PrefaceThe transceiver is programmed by using a personal computer,programming interface (KPG-46U/46X) and FPU (programmingsoftware).The programming software can be used with a PC. Figure 1shows the setup of a PC for programming.
Fig.1
2.2.5.2 Connection procedure(1) Connects the transceiver to the computer using the
interface cable (KPG-46U/46X).
Note:You must install the KPG-46U/46X driver in thecomputer to use the USB programming interface cable(KPG-46U/46X).
(2) When the POWER switch on, user mode can be enteredimmediately. When PC sends command the transceiverenter PC mode, and “PROGRAM” is displayed on the LCD.When data transmitting from the transceiver, the red LEDlights.When data receiving to the transceiver, the green LEDlights.
Note:The data stored in the computer must match the “ModelName” when it is written into the flash memory.
2.2.5.3 KPG-46U/46X description (USB programminginterface cable: Option)
The KPG-46U/46X is a cable which connects to a USB port on acomputer.When using the KPG-46U/46X, install the supplied CD (withdriver software) in the computer. The KPG-46U driver runs underWindows 7, 8.1, 10.The KPG-46X driver runs under Windows 7, 8.1, 10.The latest version of the USB driver is available for downloadfrom the following URL:http://www.kenwood.com/usb-com/(This URL may change without notice.)
2.2.5.4 Programming software KPG-D3/D3N descriptionThe FPU is the programming software for the transceiversupplied on a CD. This software runs under Windows 7, 8.1, 10.The data can be input to or read from the transceiver and editedon the screen.
Note:KPG-D3N can't be used for E type.
2.2.6 Firmware Programming Mode
2.2.6.1 PrefaceFlash memory is mounted on the transceiver. This allows thetransceiver to be upgrade when new features are released in thefuture. (For details on how to obtain the firmware, contactCustomer Service.)
2.2.6.2 Connection procedureConnect the transceiver to the personal computer using theprogramming interface (KPG-46U/46X). (Connection is same asin the PC mode.)
2.2.6.3 Programming(1) Start up the firmware programming software (KENWOOD
Firmware Loader). The KFL.exe exists in the KPG-D3/D3Ninstalled folder.
(2) Set the baud rate to "auto" or 1152000, 576000, 115200,and 57600.
(3) Set the firmware to be upgrade by file name item.(4) Enter the Firmware programming mode by using section
“2.2.2 How to Enter Each Mode”. Then, the yellow LED onthe transceiver light and "FIRMWARE PROG" is displayed.
(5) Check the connection between the transceiver and thepersonal computer, and make sure that the transceiver isin the Program mode.
(6) Press “Write” button in the window. When the transceiverstarts to receive data, the “LOADING” display lights.
(7) If writing ends successfully, the checksum is calculatedand a result is displayed.
(8) If you want to continue programming other transceivers,repeat step (4) to (7).
Note:If write is perfomed by KFL, Firmware programmingmode will start automatically even if Firmwareprogramming is set to disable in the programmingsoftware.
2.2.6.4 FunctionIf you press the [ (AUX)] button while “FIRMWARE PROG” isdisplayed, the checksum is calculated, and a result is displayed.If you press the [ (AUX)] button again while checksum isdisplayed, “FIRMWARE PROG” is redisplayed.
PC
KPG-46U/46X
+ Tuning cable
(E30-7754-05)
KPG-46U/46X
Transceiver
PC
USB
FPU
1-10 (No.RA054<Rev.001>)
2.2.7 Clone ModeProgramming data can be transferred from one transceiver toanother by connecting them via their modular microphone jacks.The operation is as follows.
The following data cannot be cloned.• Tuning data• Transceiver Embedded Message• ESN (Electronic Serial Number) data
Button guide on the Clone/ Front Panel ProgrammingPassword input screen.
• Confirm ([ ] button): The password confirmation• Delete ([ ] button): Delete the latest digit from the current
password number (Press and hold to delete all passwordnumbers)
• Select([ ] button): Determine the latest digit of thepassword number.
(1) In the source transceiver, enter the clone mode by usingsection “2.2.2 How to Enter Each Mode”. When the Clone/Front Panel Programming Password is set to thetransceiver, "Input Password" is displayed on the LCD.If the password is not set, the transceiver displays "CLONEMODE".
(2) When you enter the correct password, “CLONE MODE” isdisplayed, the transceiver can be used as the cloningsource. The following describes how to enter thepassword.
(3)- How to enter the password using the MIC keypad;
If one of the buttons 0 to 9 is pressed while the “InputPassword” is displayed, the password number isdisplayed on the LCD.Each press of the button shifts the display in order to theleft.When you enter the password and press [ ] or [*]button, “CLONE MODE” displayed if the enteredpassword is correct. If password is incorrect, “InputPassword” is redisplayed.
- How to enter password using the [] and []buttons;
If the [] / [] button is pressed while “Input Password”is displayed, the Clone/ Front Panel ProgrammingPassword input screen is displayed.If the [] or [] button is pressed while the clone/ FrontPanel Programming Password input screen is displayed,the number (0 to 9) blinks on the LCD. When you pressthe [ ] button, currently selected number isdetermined. If you press the [ ] button after enteringpassword in this procedure, “CLONE MODE” isdisplayed if entered password is correct. If the passwordis incorrect, “Input Password” is redisplayed.
(4) Power ON the target transceiver.(5) Connecting the cloning cable (part No.E30-3382-05) to the
modular microphone jacks on the source and target.(6) Press [ ] button on the source while the source displays
“CLONE MODE”. The data of the source is sent to thetarget. While the target is receiving the data, “PROGRAM”is displayed. When cloning of the data is completed, thesource displays “END”, and the target automaticallyoperates in the User mode. The target can then beoperated by the same program as the source.
(7) The other target can be continuously cloned. When the [ ] button on the source is pressed while the sourcedisplays “END”, the source displays “CLONE MODE”.Carry out the operation in step (4) to (6).
Note:• Cannot be cloned if the Password (Write) is programmed to
the target.• “Model name” must be same to clone the transceiver.
Fig.2
2.2.8 Front Panel Programming ModeIf the Front Panel Programming Mode is used, the frequency orother data of the conventional channel is rewritable only by thetransceiver.Moreover, the conventional channel can be added.
The following setup items can be changed or added byusing the Front panel programming mode.
• RX/TX Frequency• Channel Type• Transmit Mode (Mixed mode only)• Channel Spacing• Decode QT/DQT/RAN, Encode QT/DQT/RAN• Color Code• Slot Selection• Transmit Power• Channel Name
Button guide on the Clone/ Front Panel ProgrammingPassword input screen.
• Confirm ([ ] button): The password confirmation• Delete ([ ] button): Delete the latest digit from the current
password number (Press and hold to delete all passwordnumbers)
• Select ([ ] button): Determine the latest digit of thepassword number.
2.2.8.1 Enter to the Front panel programming mode.Enter to the Menu Mode by pressing [Front Panel Mode] PFbutton or [Menu] button. When the Front Panel Mode is selected,it can enter to the Front panel programming mode.If the Clone/Front panel programming Password is not set to thetransceiver, "Panel Program" is displayed on the LCD.If the Clone/Front panel programming Password is set to thetransceiver, "Panel Program" is displayed on the LCD when youenter the correct password while “Input Password” is displayed.
Cloning cable
(E30-3382-05)
(No.RA054<Rev.001>)1-11
2.2.8.2 Data WritingBefore moving to next Zone/Channel, “Keep This Change?”appears on the LCD, if you select “OK”, the new data is writtento memory. If you select “Cancel”, the new data not be written;the new data will be erased.• The setup items for Front panel programming mode are as
follows.
*3: In "Channel Type" display, "Transmit Mode" can beentered only when Mixed mode is selected.
• Button operation
No. Setup item Display Remarks
1 RX Frequency RX Frequency Receive Frequency
2 TX Frequency TX Frequency Transmit Frequency
3 Channel Type Channel Type Analog/NXDN/DMR
4 Transmit Mode*3
Transmit Mode Analog/NXDN/DMR
5 Channel Spacing
Channel Space Analog: 12.5kHz/20kHz/25kHzNote: 20kHz is applied for E type only.
NXDN:6.25kHz/12.5kHz
DMR: 12.5kHz
6 RX Signaling RX QT/DQT Receive QT/DQT
7 TX Signaling TX QT/DQT Transmit QT/DQT
8 RX RAN RX RAN None, 1~63
9 TX RAN TX RAN None, 1~63
10 Color Code Color Code 0~15
11 Slot Selection Slot Selection Slot 1, Slot 2
12 Transmit Power Transmit Power
Low/Medium/High
13 Channel Name Channel Name
No. Setup item Display Remarks
Button\Item
Zone Select Channel Select RX Frequency TX Frequency Channel Type Transmit Mode *5
Channel Spacing
[ ] Decision Decision Decision Decision Decision Decision Decision
[ ] Unused Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
[ ] Unused Unused Go to the TX Frequency
Go to the RX Frequency
Unused Unused Unused
[ ] Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
[] Zone change Channel change Frequency up Frequency up Channel type change
Transmit Mode Change
Channel Spacing Change
[] Zone change Channel change Frequency down Frequency down Channel type change
Transmit Mode Change
Channel Spacing Change
[] Unused Unused Frequency step change
Frequency step change
Unused Unused Unused
[] Unused Unused Frequency step change
Frequency step change
Unused Unused Unused
MICKeypad[0] ~ [9]
Zone number select
Channel number select
Go to the direct enter mode Channel number select (1,2 or 3)
Transmit Mode number select (1 or 2)
Channel spacing select *4
MICKeypad [*]
Decision Decision Decision Decision Decision Decision Decision
MICKeypad [#]
Unused Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
1-12 (No.RA054<Rev.001>)
*4: K typeChannel spacing select (1 or 2)E typeChannel spacing select (1, 2 or 3)
*5: Mixed Mode only
• Direct enter mode
Button\Item
RX Signaling TX Signaling RX RAN TX RAN Color Code Slot Selection
Transmit Power
Channel Name
[ ] Decision Decision Decision Decision Decision Decision Decision Decision
[ ] Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item/Delete
[ ] Unused Unused Unused Unused Unused Unused Unused Character/Digit switching
[ ] Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
[] Signaling number change
Signaling number change
RX RAN up TX RAN up Color Code up
Slot up Transmit power change
Go to the direct enter mode
[] Signaling number change
Signaling number change
RX RAN down
TX RAN down
Color Code down
Slot down Transmit power change
[] Signaling type change
Signaling type change
RX RAN ON/OFF
RX RAN ON/OFF
Unused Unused Unused
[] Signaling type change
Signaling type change
RX RAN ON/OFF
RX RAN ON/OFF
Unused Unused Unused
MIC Keypad [0] ~ [9]
Go to the direct enter mode Slot number select (1 or 2)
Transmit power select (1, 2 or 3)
MIC Keypad [*]
Decision Decision Decision Decision Decision Decision Decision Decision/ Character/ Digit switching
MIC Keypad [#]
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Button\Item
RX Frequency
TX Frequency
RX Signaling
TX Signaling
RX RAN
TX RAN
Color Code
Channel Name
[ ] Decision Character/Channel name decision
[ ] Delete
[ ] Unused Input character switching
[ ] Exit panel program mode
[] Unused Character selection (upper casecharacter → lower-case character →digit → upper case character...)
[] Character selection (upper casecharacter → lower-case character →digit → upper case character...)
[] Move a cursor to the right
[] Move a cursor to the left
MIC Keypad[0] ~ [9]
Add a digit to the current number
MIC Keypad [*]
Decision Input character switching
MIC Keypad [#]
Delete/Back to the previous item Delete
(No.RA054<Rev.001>)1-13
• Front panel programming mode flow chart
Input Password
Front panel Programming mode
tceleS enoZ?egnahC sihT peeK
tceleS lennahCemaN lennahC
Transmit Power Low Medium High Blank Channel Select the setting channel.
"System Type = Conventional"
there is more than two.
System Select Analog DMR or NXDN
RX Frfequency
FFOycneuqerF XT
golanAepyT lennahC
12.5kHz 25.0kHz 20.0kHz
When the KPG-D3N is used, 25.0kHz may not be allowed depends on the frequency (K, K2 types only).
Channel Spacing 12.5kHz
RX Signaling OFF QT DQT N DQT I
TX Signaling OFF QT DQT N DQT I
Color Code
Slot Selection
DMR
NXDN
[Channel Type]:"DMR","Mixed"(Transmit Mode:DMR) and
when two kinds of Channel Type is set.
[Channel Type]: "Analog"
[TX Frequency]: "OFF"
[Channel Type]: "Analog"
[Channel Type]: "Analog","Mixed"(Transmit Mode: NXDN),
"Mixed"(Transmit Mode: DMR) and when a kind of Channel Type is set.
[TX Frequency]: Other than "OFF"
[Channel Type]: "Analog","Mixed"(Transmit Mode: NXDN),"Mixed"(Transmit Mode: DMR)
Clone/Front Panel Password
[TX Frequency]: Other than "OFF"[Channel Type]: "DMR","Mixed"(Transmit Mode: DMR)
RX RAN
TX RAN
[TX Frequency]: "OFF"[Channel Type]: "DMR"
[System Type]: "DMR"
[System Type]: "NXDN"
6.25Hz
[Channel Type]: "NXDN","Mixed"(Transmit Mode: NXDN)
[ ]
[ ]
[ ] or [ ]
[No]
[Channel Type]: "Analog","Mixed"(Transmit Mode: NXDN),"Mixed"(Transmit Mode: DMR)
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[TX Frequency]: Other than "OFF"
[Channel Type]: "NXDN","Mixed"(Transmit Mode: NXDN)
[Channel Type]: "NXDN",
"Mixed"(Transmit Mode:NXDN) and
when two kinds of Channel Type is set.
[ ]
[ ][TX Frequency]: "OFF"
[Channel Type]: "NXDN"
[ ]
[Channel Type]: "NXDN",
"Mixed"(Transmit Mode: NXDN)
[ ]
[ ] or [ ] [ ] or [ ]
[ ] or [ ]
Mixed
[System Type]: "DMR" or ”NXDN” and [Channel Type]: "Mixed"[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ] [ ] or [ ] [ ] or [ ]
[ ] or [ ] [ ] or [ ] [ ] or [ ]
Enter the Front panel programming mode
by using section "2.2.2 How to Enter Each Mode".
[ ]
[ ] or [ ]
Transmit Mode select golanA
DMR
NXDN
[System Type]: "DMR"
[System Type]: "NXDN"
[ ] or [ ]
[ ] or [ ]
[ ] or [ ][ ] or [ ]
[Channel Type]: "Mixed" and
when Channel Spacing in two kinds of Channel Type is set.
1-14 (No.RA054<Rev.001>)
2.2.9 Transceiver Information ModeUse this function to confirm the transceiver firmware version, Encryption Library Version.
(1) Enter the Transceiver Information mode by using section "2.2.2 How to Enter Each Mode".(2) The transceiver firmware version appears on the LCD.(3) Use the [] and [] buttons to select the confirmation items.
(4) To exit the transceiver information mode, turn the transceiver power OFF.
Note:The Encryption Library Version will also display Radio Feature License (KWD-3004AE) as Inactive.
2.3 INSTALLATION
2.3.1 Connection Cable (KCT-60: Option)The KCT-60 connection cable kit is used to connect thetransceiver to a Horn alert cable, KCT-18 (Ignition sense cable),KES-5 (External speaker), or through the KCT-36 extensioncable.
2.3.1.1 Installing the KCT-60 (Connection cable) in thetransceiver
(1) Remove the ACC. cap on the rear of the transceiver.(2) Connect the D-sub connector of the KCT-60 to the D-sub
15-pin terminal of the transceiver.(3) Connect the 15-pin connector of the KCT-60 to a Horn alert
cable, KCT-18, KES-5, or through a KCT-36 extensioncable.
Note:You must setup using the KPG-D3/D3N.
2.3.1.2 Terminal function
2.3.2 Horn Alert FunctionThe Horn alert function (max. 2A drive) is enabled by installingthe KCT-60 in the transceiver.
2.3.2.1 Installation Procedure(1) Remove the ACC. cap on the rear of the transceiver.(2) Connect the D-sub connector of the KCT-60 to the D-sub
15-pin terminal of the transceiver.(3) Insert the two crimp terminals of the Horn alert cable to pins
13 and 14 of the square plug.(4) Connect the square plug to the 15-pin connector of the
KCT-60.(5) Connect the remaining two Horn alert cables to your car
Horn alert signal control.The internal FET switch can be controlled by turning the HAfunction on/off and by using a signaling decode output. Themaximum current of HA is 2A. This switch is the FET switchof P-channel type. Therefore, a DC power supply isnecessary to use the HR1. The voltage range is from 5V to16V.
Note:You must set up using the KPG-D3/D3N.
Transceiver
firmware versionEncryption Library
Version
[ ]/[ ]
[ ]/[ ]
D-sub 15-pin Pin No. Name Molex 15-pin Pin No.
1 SB 1
2 IGN 2
3 PA or EXT-SP 12
4 DO 4
5 DI 5
6 FNC1 9
7 FNC2 11
8 FNC3 7
9 FNC4 6
10 FNC5 8
KCT-60
Horn alert cable,
KCT-18, KES-5 or through
KCT-36 extension cable
11 FNC6 10
12 5C -
13 HR1 13
14 HR2 14
15 GND 3
D-sub 15-pin Pin No. Name Molex 15-pin Pin No.
3. GND
13. HR1
14. HR2
13
14 Square plug
13
14
15
10
11
12
7
8
9
4
5
6
1
2
3
KCT-60
Crimp terminalHorn alert cable
(No.RA054<Rev.001>)1-15
2.3.3 Ignition Sense Cable (KCT-18: Option)The KCT-18 is an optional cable for enabling the ignitionfunction. The ignition function lets you turn the transceiver poweron and off with the car ignition button.
2.3.3.1 Installing the KCT-18 (Ignition sense cable) in thetransceiver
2.3.4 External Speaker (Option)
2.3.4.1 KES-5External speaker KES-5 can be installed for KCT-60.
Connection procedure(1) Remove the ACC. cap on the rear of the transceiver.(2) Connect the D-sub connector of the KCT-60 to the D-sub
15-pin terminal of the transceiver.(3) Insert the two crimp terminals of the KES-5 to pins 3 and
12 of the square plug.(4) Connect the square plug to the 15-pin connector of the
KCT-60.
Note:You must set up using the KPG-D3/D3N.Before the external speaker can be used, you must assignone of the buttons as “External Speaker”, using the KPG-D3/D3N.
2.3.5 Changing Serial Port Level
2.3.5.1 Change FNC1 (TXD) and FNC2 (RXD) of D-SUB 15-pin connector from TTL level to RS-232C level
FNC1 (TXD /6pin ) and FNC2 (RXD /7pin ) of D-SUB 15-pinconnector are confi gured at the TTL level as the default value.But you can change these serial port level to RS-232C levelthrough the RS-232C level converter IC (IC605) by confi guringthe port.Remove the R625, R633 and R634 chip jumpers and sol-der thechip jumpers to R605, R610 and R611.
2.3.5.2 Change FNC1 (TXD), FNC2 (RXD), FNC3 (RTS) andFNC4 (CTS) of D-SUB 15-pin connector from TTLlevel to RS-232C level
FNC1 (TXD /6pin ), FNC2 (RXD /7pin ), FNC3 (RTS /8pin ) andFNC4 (CTS /9pin ) of D-SUB 15-pin connector are configured atthe TTL level as the default value. But you can change theseserial port level to RS-232C level through the RS-232C levelconverter IC (IC605) by confi guring the port.Remove the R623, R625, R630, R631, R633 and R634 chipjumpers and solder the chip jumpers to R604, R605, R608,R609, R610 and R611.
In the case of 5-1.[TTL level]R625,R633 and R634: 0ohm chip jumper.R605, R610 and R611: open.[RS-232C level]R605, R610 and R611: 0ohm chip jumper.R625, R633 and R634: open.
In the case of 5-2.[TTL level]R623, R625, R630, R631, R633 and R634: 0ohm chip jumper.R604, R605, R608, R609, R610 and R611: open.[RS-232C level]R604, R605, R608, R609, R610 and R611: 0ohm chip jumper.R623, R625, R630, R631, R633 and R634: open.
2.3.6 Changing of Signal Type
2.3.6.1 Change signal output of D-SUB connector fromDEO to AFO
The output (4pin) of D-SUB 15-pin connector is confi gured at theDEO as the default value. Remove the R613 chip jumper and solder the clip jumper toR612.
2.3.6.2 Change signal input of D-SUB connector from DI toMI2
The input (5pin) of D-SUB 15-pin connector is confi gured at theDI as the default value.Remove the R659 chip jumper and solder the chip jumper toR601.
KCT-60
2
Ignitionline of the car
Square plug
13
14
15
10
11
12
7
8
9
4
5
6
1
2
3
KCT-18
KCT-60
Square plug
13
14
15
10
11
12
7
8
9
4
5
6
1
2
3
12
3
Black lead
Black/
White lead
7 8
11 12 15 16
R625
R605
R631
R609
R623
R604
R634
R611
R633
R610
R630
R608
R601
R659
R613
R612
5 6
1-16 (No.RA054<Rev.001>)
2.4 CIRCUIT DESCRIPTION
2.4.1 OverviewThe NX-3720H/3720 is a VHF Analog FM & Digital Mobile transceiver designed to operate in the frequency range of 136 to 174MHz.The NX-3820H/3820 is a UHF Analog FM & Digital Mobile transceiver designed to operate in the frequency range of 450 to 520MHz(K) or 400 to 470MHz (K2, E).The unit consists of a transceiver IC, a transmitter, a digital control unit, and a power supply circuit.
2.4.2 Frequency ConfigurationThe receiver uses the direct conversion system. Incoming signals from the antenna are mixed with the local signal from the PLL circuitand converted to the baseband signal. The transmit signal frequency is generated by the VCO/PLL, and modulated by the signal fromthe DSP. It is then amplified and fed to the antenna.
Fig.1 Frequency Configuration
2.4.3 Receiver System
2.4.3.1 RF circuitThe receive signal from ANT SW (D205, D206, D207, D208 and D209) passes through the high-pass filter (L303, L304, L313, L315and L317 (L315 and L317 are the NX-3720H/3720 only.)) to remove unwanted signals and amplified by a RF amplifier (incorporatedin IC302) . The signal is then fed to the mixer (incorporated in IC302) and converted to the baseband signal.
2.4.3.2 Baseband circuitThe baseband signal is then be fed into an ADC (incorporated in IC302), generates the I and Q data. This data is in the form of SerialInterface, and sent to the MPU/DSP (IC404).
Fig.2 RF and Baseband circuit
2.4.3.3 Audio amplifier circuitAudio processing (high-pass filter, low-pass filter, de-emphasized and so on) at Analog FM mode and decoding at Digital mode areprocessed by MPU/DSP. I2S signal from DSP is converted to audio signal at IC607. The signal goes to internal speaker and connectorfor external speaker (J2) through the electronic volume control (IC412), pre amplifier (IC608) and audio power amplifier (IC601).
ANT SW
FINAL AMP
DRIVE AMP
TRANSCEIVER IC
VCO
TCXO 19.2MHz
BASEBAND CIRCUIT
CODEC
AF AMP
MIC
SP
ANT
ANT
LPF SW
D205, D206
D207, D208
D209
ANT
L303,L304
L313,L315
L317
HPF
IC302
L308, L309
L310, L311
HPF
RFAMP MIXER
PLL
VCO
ADC
Serial
I/F
IC404
MPU/DSP
(No.RA054<Rev.001>)1-17
2.4.4 Transmitter System
2.4.4.1 Audio Band CircuitThe signal from microphone is amplified and converted to digital signal by IC607. IC607 includes AGC function.Digital signal is transferred to IC404.
2.4.4.2 Baseband CircuitThe audio signal transferred from IC607 is processed at IC404.Voice signals of 300Hz or lower and frequencies of 3 kHz or higher arecut off and an audio range 300Hz to 3 kHz is extracted. The audio signal is then pre-emphasized in FM mode and synthesized withthe signals, such as QT and DQT, as required, and is transferred to PLL Frequency Synthesizer block in IC302. The DTMF and MSKbaseband signals are also generated by IC404.In Digital mode, the audio signal is converted to the 4-Level FSK baseband signal and is transferred to PLL Frequency Synthesizerblock in IC302.
2.4.4.3 Drive and Final amplifierThe RF signal from IC302 is amplified by pre-drive amplifier (IC202). The output of the pre-drive amplifier is amplified by the driveamplifier (Q201) and RF Power module (IC201) to 50W [NX-3720H], 45W [NX-3820H], 25W [NX-3720, NX-3820] (5W when the poweris low). IC202 is MMIC.Q201 is MOS FET. The output of the final amplifier is then passed through the coupler, antenna switch (D205,D206 and D207), harmonic filter (LPF) and applied to the antenna terminal.
2.4.4.4 APC circuitThe Automatic transmission power control (APC) circuit controls the transmitter output in adjusted value by monitoring it with a coupler.RF detection and comparison functions are included in the power-control IC (IC205).The power control IC output is given as a drive source of the RF power module’s gate (IC201), and completes APC feedback loop.When a normal antenna load is connected, forward RF Power is detected by the coupler and direct in power-control IC (IC205).Forward RF Power is converted into DC voltage in IC205 and compared with the SPC.The output voltage goes through DC amp (IC203 2/2) to Drive amp (Q201) and RF Power module (IC201).The voltage controls the gate bias voltage of Q201 and IC201, and keeps transmission output stable.
Fig.3 Drive and Final amplifier and APC circuit
2.4.5 PLL Frequency Synthesizer
2.4.5.1 TCXO (X401)TCXO (X401) generates a reference frequency of 19.2MHz for the PLL frequency synthesizer. This reference signal is buffered byQ401. And it is distributed to PLL (IC302).The oscillation frequency is adjusted TCXO directly by controlled the D/A converter of FCNT.
IC302 Pre-Drive
IC202 Q201
Drive
Gate Bias 1 Gate Bias 2
IC201
Final
SPC
IC205
Coupler
PA
CTRL
DC
AMP
IC203
DC
AMP
REV
DETREV
D204
ANT
SW
D205,D206 D207 D208,D209
ANT
LPF
1-18 (No.RA054<Rev.001>)
2.4.5.2 VCO• NX-3720H (K), NX-3720 (E)
There is one VCO contain TX VCO and RX VCO.The VCO (Q105) generates the carrier for the transmitter and the receiver. VCO oscillation frequency range is 272 to 348MHz. Thetransmit frequency range is same as receiver frequency range.The local signal frequency range is also 272 to 348MHz.The oscillation frequency is divided into two by IC 302 and it becomes the use frequency.The VCO oscillation frequency is determined by voltage control terminals "CP" and "ASSIST".The voltage control terminal "CP" is controlled by PLL (IC302). The voltage control terminal "ASSIST" is controlled by the controlvoltage from D/A converter (IC411).For the modulation input terminal, "VCO_MOD" of PLL (IC302), the output frequency changes according to the applied voltage. Thisis used to modulate the VCO output.
• NX-3820H (K)There is one VCO contain TX VCO and RX VCO.The VCO (Q105) generates the carrier for the transmitter and the receiver. VCO oscillation frequency range is 300 to 346.7MHz.The transmit frequency range is same as receiver frequency range.The local signal frequency range is 900 to 1040MHz. The local signal is three times the number of VCO oscillation frequency range.The output frequency is divided into two by IC 302 and it becomes the use frequency.The VCO oscillation frequency is determined by voltage control terminals "CP" and "ASSIST".The voltage control terminal "CP" is controlled by PLL (IC302). The voltage control terminal "ASSIST" is controlled by the controlvoltage from D/A converter (IC411).For the modulation input terminal, "VCO_MOD" of PLL (IC302), the output frequency changes according to the applied voltage. Thisis used to modulate the VCO output.
• NX-3820H (K2), NX-3820 (E)There is one VCO contain TX VCO and RX VCO.The VCO (Q105) generates the carrier for the transmitter and the receiver. VCO oscillation frequency range is 266.7 to 313.3MHz.The transmit frequency range is same as receiver frequency range.The local signal frequency range is 800 to 940MHz. The local signal is three times the number of VCO oscillation frequency range.The output frequency is divided into two by IC 302 and it becomes the use frequency.The VCO oscillation frequency is determined by voltage control terminals "CP" and "ASSIST".The voltage control terminal "CP" is controlled by PLL (IC302). The voltage control terminal "ASSIST" is controlled by the controlvoltage from D/A converter (IC411).For the modulation input terminal, "VCO_MOD" of PLL (IC302), the output frequency changes according to the applied voltage. Thisis used to modulate the VCO output.
2.4.5.3 PLL ICPLL (IC302) compares the difference in phases of the VCO oscillation signal and the TCXO(X401) reference frequency. And it returnsthe difference voltage to the VCO CP terminal and realizes the "Phase Locked Loop".This allows the VCO oscillation frequency to accurately match (lock) the desired frequency.When the frequency is controlled by the PLL, the frequency convergence time increases as the frequency difference increases whenthe set frequency is changed. To supplement this, The ASSIST Voltage from D/A converter (IC411) is used before control by the PLL(IC302) to bring the VCO oscillation frequency close to the desired frequency. As a result, the VCO CP voltage does not change andis always stable at approx. 2.5V.The desired frequency is set for the PLL (IC302) by the MPU/DSP (IC404) through the 3-line "/DCR_CS", "DCR_DO", "BCLK" serialbus for PLL. IC404 monitors through the "PLD", whether the PLL (IC302) is locked or not. If the VCO does not lock to desired frequency(unlock), the "PLD" logic is low.
2.4.6 Control CircuitThe control circuit consists of MPU/DSP (IC404) and its peripheral circuits. IC404 mainly performs the following;
(1) Switching between transmission and reception by PTT signal input.(2) Reading system, zone, frequency, and program data from the memory circuit.(3) Sending frequency program data to the PLL.(4) Controlling the audio mute circuit by decode data input.
2.4.6.1 MPUThe MPU/DSP (IC404) is 32bit RISC processor and Fixed/Floating-Point VLIW DSP, equipped with peripheral function.This MPU operates at 288MHz (MAX) clock and 3.2V /1.8V/1.2V DC. Controls the flash memory, Mobile DDR, the receive circuit, thetransmitter circuit, the control circuit, and the display circuit and transfers data to or from an external device.
2.4.6.2 Memory CircuitMemory circuit consists of the MPU/DSP (IC404) and the Mobile DDR (IC402), the flash memory (IC401). The flash memory hascapacity of 512Mbit that contains the transceiver control program for the MPU and stores the data. It also stores the data for transceiverchannels and operating parameter that are written by the FPU. This program can be easily written from external devices. The MobileDDR has capacity of 512Mbit. The MPU copies the program to the Mobile DDR from Flash memory. And MPU is used as a work areaMobile DDR.
(No.RA054<Rev.001>)1-19
Flash memory
Note:The flash memory stores the data that is written by the FPU (KPG-D3/D3N), tuning data (Deviation, Squelch, etc.), and firmwareprogram (User mode, Test mode, Tuning mode, etc.). This data must be rewritten when replacing the flash memory.
Mobile DDR (static memory)
Note:Mobile DDR is used as a work area of the MPU.
2.4.6.3 LCDLCD interface connector (CN6) of the SUB unit.The LCD is controlled using parallel interface from MPU/DSP (IC404) through the interface connectors (CN1 of the TX-RX unit andCN7 of SUB unit) and flexible cable.
2.4.6.4 Button Detection CircuitButtons are detected using I/O Expander IC (IC6) of the SUB unit. If pressed button is detected by IC6, it is informed to MPU/DSP(IC404) of the TX-RX unit through serial line.
2.4.6.5 DSPThe DSP circuit consists of a MPU/DSP (IC404) and processes the baseband signal. The DSP operates at 288MHz (MAX) clock, theI/O section operates at 3.2V/1.8V and the core section operates at 1.2V. The DSP carries out the following processes:• 4Level FSK processing• Analog FM pre-emphasis/de-emphasis• Vocoder processing between audio codec and modulation/demodulation• CAI processing, such as error correction encoding• QT/DQT encoding/decoding• DTMF encoding/decoding• MSK encoding/decoding• 2-tone /5-tone encoding/decoding• Compressor/expander processing• Voice scrambler processing• Transmit/receive audio filtering processing• Microphone amplifier AGC processing• Audio mute processing• Modulation level processing• Active Noise Reduction• Voice recording/playback processing• Voice announce processing
2.4.7 Power Supply Circuit+B is connected to RF Power Module, 50BU regulator (Q15, Q16 and D13) through the fuse (F1), DC/DC converter IC (IC25) via fuse(F1), SB1 switch (Q12 and Q13) through the fuse (F4) and SB2 switch (Q17 and Q18) through the fuse (F5).Q15, Q16 and D13 regulates +B voltage to 5V (50BU). Then IC13 regulates 50BU to 3.1V (31BU). Then IC15 regulates 31BU to 1.2V(12BU). 50BU, 31BU and 12BU operate whenever +B is supplied.IC25 regulates +B voltage to 5.4V (54M). 54M is controlled by BAT_CNT signal from Power management IC (IC22). When Powerswitch is turned on, BAT_CNT signal is controlled by /PSW signal. 54M goes to DC/DC converter ICs (IC24, IC12) and AVR ICs (IC20,IC17, IC26, IC609, IC23).IC24 (12M) is enabled while the 54M is operating. 12M provides the power to the MPU/DSP (IC404) and turns on IC12 (18M). 18Mprovides the power to the MPU/DSP and DDR (IC402) and turns on IC20 (32M). 32M provides the power to the MPU/DSP, Flashmemory (IC401) and many control circuits and turns on IC17 (32A), IC26 (50A). Then 32A turns on IC21 (18M_3). The Power management IC (IC22) watches +B voltage. If +B voltage is higher than 8.5V, IC22 outputs high voltage to the /BINTterminal. If the /BINT is high, SB1 (Q12 and Q13) and SB2 (Q17 and Q18) are turned on by SBC signal from MPU/DSP (IC404). Inthe same way, IC609 (50AC) and IC23 (50C) and IC19 (32C) are turned on by SBC. 50C is fed to IC14 (200C). IC14 (200C) is theDC/DC boost converter. The 200C circuit then outputs approximately +20VDC. SB1 supplies SUB unit and Audio power amplifier (IC601) with +B voltage. SB2 supplies D-sub unit and 9VAVR (IC1) with +B voltage.Then IC1 regulates +B to 9V (90C). Then IC16 regulates 90C to 5V (50CT). If the MPU/DSP (IC404) controls TXC, ANT SW andASSW signals to High, Q20, Q23 (90T), Q21, Q22 (90ANT) and Q206 are turned on and transmission circuits are enabled to transmit.When the Power management IC (IC22) and MPU/DSP (IC404) detect /PSW signal (Power switch), /IGN signal (Ignition sense) and/BINT signal, they set the SBC signal to Low, and turn the transceiver power off.When D20, Q11 detect over-voltage condition, they turn SB1 and SB2 off, and transfer that the MPU/DSP (IC404) through IC22.
1-20 (No.RA054<Rev.001>)
Fig.4 Power Supply Circuit
54M 12M
31BU
12BU
18M
18M_3
CODEC DVDD
18M
Power management
Sub unit
Module unit
50A
[SBC]
32C
200C50C
50B F1
20V DC/DC
54M
SB1
D-sub 15
TX circuit90C
[SBC]
90ANT
SB2
TX PreDrive(MMIC)50CT
Sub unit
Audio Power Amp
[TXC]
90T
Antenna switch
IC1
IC16
IC19
3.2V AVR
50AC
[SBC]
[SBC]
+
[ANTSW]
[ASSW]
IC255.4V DC/DC
(IC22)Power management IC
[BAT_CNT]from
Q15,Q16,D13
5V Reg
IC13
3.1V AVR
BackUpBattery
IC151.2V AVR
IC241.2V DC/DC
IC12DC/DC1.8V
MPU/DSP I/O(B),DDR
Mobile DDR2,Sub unit
RF Power Module
MPU/DSP PLL
MPU/DSP Core
MPU/DSP RTC
Power management IC
Flash ROMV(I/O) & 3state(512M)
MPU/DSP I/O(A,C) DVDD, USB_VDDA33
Flash ROM, I/O Expander,ADC, CODEC
19.2M TCXO circuit, Uart SW, RS232C
driver, SP GND switch clock, Sub unit
8bit/8ch DAC
12bit/4ch DAC
CODEC AVDD,DRVDD
I/O Expander, D-sub level shift.
8bit/16ch ADC AVCC
OPamp for VREF/25REF
MPU/DSP USB_VBUS
SP GND switch driver
Sub unit
D-sub 15
VCO Assist
Direct Conversion Transceiver
RF Detector / Controller
IC21
DC SW
32A
32M3.2V AVR
IC20
32A
32M
IC173.2V AVR
32M
IC265V AVR
IC6095V AVR
IC235V AVR
IC14
F4
F5
Q12, Q13DC SW
Q17, Q18DC SW
5V AVR
Q206
Q 20, Q 23DC SW
DC SW
Q 21, Q 22DC SW
9V AVR
(No.RA054<Rev.001>)1-21
2.4.8 Signaling Circuit
2.4.8.1 Encode (QT/DQT/DTMF/2-tone /MSK)Each signaling data signal of QT, DQT, DTMF, 2-tone and MSK is generated by IC404, superposed on a modulation signal and outputto VCO and PLL.
2.4.8.2 Decode (QT/DQT/DTMF/2-tone/MSK)The audio signal and signaling data (QT, DQT, DTMF, 2-tone and MSK) are separated by IC404. Next IC404 decode the signalingdata.
2.4.9 Bluetooth/GPS Circuit (GPS model only)The main component of the Bluetooth/GPS circuit is Bluetooth/GPS IC (IC5) on Module unit.The clocks of Bluetooth/GPS IC require 19.2MHz for core and 32.768 kHz slow clock (X1 and X2) for UART.Bluetooth/GPS IC communicates to the MPU/DSP (IC404) on the HCI UART. Interface of UART & Digital audio (PCM) between theMPU/DSP (IC404) and the Bluetooth/GPS IC (IC5), have level conversion at the level conversion IC (IC6 and IC7) on Module unit.The Bluetooth/GPS IC is powered by 1.8V and 3.3V which are supplied from 2 discrete external regulators (IC2 and IC3) on Moduleunit.
Fig.5 Bluetooth/GPS Circuit
X1 X2
TX-RX unit
IC404
MPU/DSP
UART
PCM
Module unit
PCM
UART
IC6
IC7
Level Conversion
IC
Conversion IC
Level UART
PCM
IC5
BT/GPS
IC
BPF
BPF
Bluetooth
antenna
GPS
antenna
connector
CN532.768kHz
Clock
TCXO 19.2MHz
1-22 (No.RA054<Rev.001>)
2.4.9.1 Bluetooth CircuitTX/RX frequency is 2400-2483.5MHz (79ch Hopping, 2402-2480MHz, 1MHz step). Transmitting power is +2dBm at Bluetoothantenna input.Using the printed antenna with Bluetooth, and connected to the Bluetooth/GPS IC (IC5) through the saw filter (L11).Frequency configuration for Bluetooth is following:There are two LO modes: 2X and Offset LO (OSLO). 2X where LO is 2*RF_FREQ (e.g. when transmitting at 2441MHz it is at4882MHz). OSLO where LO is at (2/3)*RF_FREQ (e.g. when transmitting at 2441MHz it is at 1627.333MHz). In RX the 2X is always used. In GFSK TX if power is >10dBm then OSLO is usedIn EDR2 TX if power is >-12dBm then OSLO is usedIn EDR3 TX if power is >-12dBm then OSLO is usedOtherwise 2X is used for TX as well.
2.4.9.2 GPS CircuitThe GPS RF signal is received with the active antenna, and connected to the Bluetooth/GPS IC (IC5) through the terminal (CN5) andsaw filter (L9).The output is passed to pin L2 of the GPS IC. The input match for pin L2 comprises of C38, C36 and L7. The control and data linesfor the GPS IC are GPS_PA_EN, BTFM_nSHUTDOWN, GPS_TX and GPS_RX. GPS_TX and GPS_RX are shared with Bluetoothdata line. Frequency configuration for GPS is following:Lo is GPS: 1571.324MHz
Fig.6 GPS Circuit
BPF
GPS
antenna
TCXO
19.2MHz
MPU/DSP
IC404
1.8V
3.3V
GPS_LNA_IN(L2)
TCXO_CLK_LV(F1)
BT_HCI_UART_TX(A4)
BT_HCI_UART_RX(B5)
RTC_CLK(H9)OSCILLATOR
32.768kHz
BTFM_nSHUTDOWN(A6)
GPS_PA_EN(G3)
VBAT1(A2)
Level
Conversion
TCXO_LDO_IN(H1)
VDDS
GPS TX
GPS_RX
BT
antenna
BT_RF
BT/GPS IC
Antenna
connector
BPF
GPS ANT ALM
GPS ANT PWRGPS
Antenna
Detect3.3V
33GPS
33BT
18BT
(No.RA054<Rev.001>)1-23
2.5 COMPONENTS DESCRIPTION
2.5.1 TX-RX unit (XC1-182K-00,XC1-183K-XX)
Ref. No. Part Name Use / Function
IC1 IC Voltage regulator (90C)
IC12 IC DC/DC converter (18M)
IC13 IC Voltage regulator (31BU)
IC14 IC DC/DC converter (200C)
IC15 IC Voltage regulator (12BU)
IC16 IC Voltage regulator (50CT)
IC17 IC Voltage regulator (32A)
IC18 IC Ignition
IC19 IC Voltage regulator (32C)
IC20 IC Voltage regulator (32M)
IC21 IC Load Switch (18M_3 )
IC22 IC Power management
IC23 IC Voltage regulator (50C)
IC24 IC DC/DC converter (12M)
IC25 IC DC/DC converter (54M)
IC26 IC Voltage regulator (50A)
IC101 IC DC amplifier (CV/Assist)
IC202 IC MMIC (Pre-drive)
IC203 IC DC amplifier (APC)
IC205 IC RF power control
IC301 IC Attenuation
IC302 IC Transceiver IC
IC401 IC Flash memory
IC402 IC SDRAM
IC403 IC Logic control
IC404 IC MPU/DSP
IC405,406 IC Analog switch
IC407,408 IC Logic control
IC409 IC I/O expander
IC410 IC A/D converter
IC411,412 IC D/A converter
IC413 IC Ignition
IC414 IC DC amplifier (VREF/25VREF)
IC602,603 IC Logic control
IC604 IC I/O expander
IC605 IC RS232C Driver
IC606 IC Logic control
IC607 IC Codec
IC608 IC Audio amplifier
IC609 IC Voltage regulator (50AC)
Q11 Transistor DC switch (OVRB)
Q12 FET DC switch (SB1)
Q13,14 Transistor DC switch
Q15,16 Transistor Voltage regulator (50BU)
Q17 FET DC switch (SB2)
Q18 Transistor DC switch
Q19 FET DC switch
Q20 FET DC switch (90T)
Q21 Transistor DC switch
Q22 FET DC switch (90ANT)
Q23 Transistor DC switch
Q25 Transistor DC switch (SBC)
Q101 Transistor Tripler
Q102 Transistor Tripler
Q103 FET DC switch
Q104 Transistor Ripple filter
Q105 FET VCO oscillation
Q106,107 Transistor VCO Buffer amplifier
Q201 FET TX Drive amplifier
Q202 Transistor DC switch
Q204-206 Transistor DC switch
Q301 FET DC switch
Q401 Transistor TCXO Buffer amplifier
Q402-404 FET DC switch
Q601 FET Level conversion
Q602 Transistor DC switch
Q603 FET Horn alert switch
Q604 Transistor Audio mute
Q605 FET Audio mute
Q606 FET DC switch
D1 Zener diode Reverse protection
D13 Zener diode Voltage regulator (50BU)
D14,15 Diode Reverse current prevention
D16,17 Diode DC/DC converter
D18,19 Diode Reverse current prevention
D20 Zener diode Over voltage protection
D21 Diode Reverse current prevention
D22 Zener diode Over voltage protection
D24 Diode Backup battery charge
D26,27 Diode Reverse current prevention
D101 Zener diode Over voltage protection
D102 Variablecapacitance diode
VCO frequency control
D103-106 Variablecapacitance diode
VCO assist tune
D107 Zener diode Speed up
D108 Variablecapacitance diode
TX modulation
D201 Zener diode Over voltage protection
D202 Diode RF switch
D204 Diode TX Reverse power detection
Ref. No. Part Name Use / Function
1-24 (No.RA054<Rev.001>)
2.5.2 SUB unit (XC3-050M-00)
2.5.3 Module(BT/GPS) unit (XC2-0040-10)
2.6 TERMINAL FUNCTION
2.6.1 TX-RX unit (XC1-182K-00,XC1-183K-XX)
D205-209 Diode Antenna switch
D301-304 Diode Excessive input protection
D401 Diode Reverse current prevention
D402-406 Diode Line protection
D407 Zener diode Over voltage protection
D408-410 Diode Reverse current prevention
D601 Zener diode Over voltage protection
D602 Diode Reverse current prevention
D603-608 Zener diode Line protection
D609,610 Diode Line protection
D611 Zener diode Over voltage protection
D612,613 Diode Line protection
D614,615 Diode Reverse current prevention
D616,617 Diode Surge protection
D618 Diode Over voltage protection
D619 Diode Reverse current prevention
Ref. No. Part Name Use / Function
IC1 IC Voltage regulator (50M)
IC3,4 IC Level conversion
IC5 IC Bus switch
IC6 IC I/O expander
Q1 FET DC switch
Q2 FET DC switch (KEY Illumination)
Q3,4,6 Transistor DC switch (TX/BUSY)
Q8 FET DC switch (LCD backlight)
D1,2 Diode Surge protection
D3-6 LED KEY Illumination
D9,10 LED LCD backlight
D11,12 LED KEY Illumination
D15,16 LED LCD backlight
D17,18 LED KEY Illumination
D20 LED TX/BUSY LED
D21 Zener diode Over voltage protection
D22 Diode Reverse current protection
D24 Zener diode Over voltage protection
D26 Zener diode Over voltage protection
D27 Diode Over current protection
D28 Zener diode Over voltage protection
D30 Zener diode Over voltage protection
D32 Zener diode Over voltage protection
D33,34 LED KEY Illumination
Ref. No. Part Name Use / Function
Ref. No. Part Name Use / Function
IC1 IC Level conversion
IC2 IC Voltage regulator (18BT)
IC3 IC Voltage regulator (33BT)
IC4 IC Voltage regulator (33GPS)
IC5 IC GPS/Bluetooth
IC6,7 IC Level conversion
Q1 FET DC switch
D17,18 Diode Over voltage protection
Pin No. Name I/O Function
CN1
1 GND - Ground
2 GND - Ground
3 GND - Ground
4 NC - No connection
5 SP+ O Speaker output
6 SP+ O Speaker output
7 SP+ O Speaker output
8 NC - No connection
9 GND - Ground
10 GND - Ground
11 GND - Ground
12 GND - Ground
13 IGN - Ignition sense input
14 SB1 O Switched power supply
15 SB1 O Switched power supply
16 SB1 O Switched power supply
17 SB1 O Switched power supply
18 NC - No connection
19 54M O 5.4V output
20 NC - No connection
21 32M O 3.2V output
22 NC - No connection
23 18M O 1.8V output
24 NC - No connection
25 GND - Ground
26 USB_D+ I/O USB0 PHY data plus
27 GND - Ground
28 USB_D- I/O USB0 PHY data minus
29 GND - Ground
30 NC - No connection
31 MIC/VBUS I MIC signal input / USB VBUS Detection
(No.RA054<Rev.001>)1-25
2.6.2 Module (BT/GPS) unit (XC2-0040-10)
2.6.3 Sub unit (XC3-050M-00)
32 ME - MIC ground
33 /PTT I PTT input
34 DM I/O MIC data detection
35 /PSW I Detection signal input of power switch
36 TXD O Serial data output
37 RXD I Serial data input
38 GND - Ground
39 I2CDT I/O I2C serial data
40 I2CCK O I2C serial clock
41 /KEYINT I Key state change signal
42 P_TEMP I Temperature detection signal
43 /CS O LCD driver chip-serect signal
44 LCDRST O LCD driver reset signal
45 /RD O LCD driver RD signal
46 D[7] O LCD driver data output
47 D[6] O LCD driver data output
48 D[5] O LCD driver data output
49 D[4] O LCD driver data output
50 D[3] O LCD driver data output
51 D[2] O LCD driver data output
52 D[1] O LCD driver data output
53 D[0] O LCD driver data output
54 /WR O LCD driver WR signal
55 A23 O LCD driver data/command switch signal
56 GND - Ground
57 R_SET2 I Radio setting signal 2
58 R_SET1 I Radio setting signal 1
59 R_SET0 I Radio setting signal 0
60 GND - Ground
CN2
1 GPS_PWR I Antenna power supply detection
2 GPS_ALM I Antenna open/short detection
3 GND - Ground
4 GND - Ground
5 GPS_ANT_SW O Enable signal for 33GPS
6 GPS_PA_EN O GPS receiver part switching signal output
7 /BT_SHUTDOWN O Shutdown signal output
8 WCLK O Audio serial data bus word clock output
9 BCLK O Audio serial data bus bit clock output
10 BT_AUD_DI I Audio signal input
11 BT_AUD_DO O Audio signal output
12 RTS2 O Serial data output
Pin No. Name I/O Function
13 CTS2 I Serial data input
14 G_RXD2 I Serial data input
15 G_TXD2 O Serial data output
16 BT_SW O Enable signal for 33BT and 18BT
17 GPSBT_DET I BT/GPS unit detection
18 GND - Ground
19 54M O 5.4V output
20 54M O 5.4V output
Pin No. Name I/O Function
CN1
1 54M I 5.4V input
2 54M I 5.4V input
3 GND - Ground
4 GPSBT_DET O BT/GPS unit detection (Ground)
5 BT_SW I Enable signal for 33BT and 18BT
6 G_TXD2 I Serial data intput
7 G_RXD2 O Serial data output
8 CTS2 O Serial data output
9 RTS2 I Serial data input
10 BT_AUD_DO I Audio signal input
11 BT_AUD_DI O Audio signal output
12 BCLK I Audio serial data bus bit clock input
13 WCLK I Audio serial data bus word clock input
14 /BT_SHUTDOWN I Shutdown signal input
15 GPS_PA_EN I GPS receiver part switching signal input
16 GPS_ANT_SW I Enable signal for 33GPS
17 GND - Ground
18 GND - Ground
19 GPS_ALM O Antenna open/short detection
20 GPS_PWR O Antenna power supply detection
Pin No. Name I/O Function
J1
1 DM I/O MIC data detection
2 HOOK/RXD/D- I/O Hook detection / Serial data input / USB PHY data minus
3 MIC/VBUS I MIC signal input
4 ME - MIC ground
5 PTT/TXD I/O PTT input / Serial data output
6 GND - Ground
7 SB O Switched power supply
Pin No. Name I/O Function
1-26 (No.RA054<Rev.001>)
8 BLC/D+ I/O Back light control signal / USB PHY data plus
CN3
1 GND - Ground
2 S8 I Switch 8
3 S9 I Switch 9
4 S10 I Switch 10
5 S7 I Switch 7
6 S6 I Switch 6
7 S5 I Switch 5
8 S4 I Switch 4
9 S1 I Switch 1
10 S2 I Switch 2
11 S3 I Switch 3
12 /PSW I Detection signal input of power switch
CN6
1 ESD - Ground
2 A0 O LCD driver data/command switch signal
3 /WR O LCD driver WR signal
4 D0 O LCD driver data output
5 D1 O LCD driver data output
6 D2 O LCD driver data output
7 D3 O LCD driver data output
8 D4 O LCD driver data output
9 D5 O LCD driver data output
10 D6 O LCD driver data output
11 D7 O LCD driver data output
12 /RD O LCD driver RD signal
13 RSTB O LCD driver reset signal
14 CSB O LCD driver chip-serect signal
15 VDDI O 1.8V output
16 VD1 - LCD Driver Internal power supply
17 VSS - Ground
18 VDD O 3.2V output
19 VM - VM is the non-select voltage level of COM-drivers
20 V0 - V0 is the LCD driving voltage for common circuits at positive frame
21 XV0 - XV0 is the LCD driving voltage for common circuits at negative frame
22 VG - VG is the LCD driving voltage for segment circuits
23 ESD - Ground
CN5
1 SP+ O Speaker output
2 SPG - Speaker ground
Pin No. Name I/O Function
CN7
1 GND - Ground
2 R_SET0 O Radio setting signal 0
3 R_SET1 O Radio setting signal 1
4 R_SET2 O Radio setting signal 2
5 GND - Ground
6 A23 I LCD driver data/command switch signal
7 /WR I LCD driver WR signal
8 D[0] I LCD driver data input
9 D[1] I LCD driver data input
10 D[2] I LCD driver data input
11 D[3] I LCD driver data input
12 D[4] I LCD driver data input
13 D[5] I LCD driver data input
14 D[6] I LCD driver data input
15 D[7] I LCD driver data input
16 /RD I LCD driver RD signal
17 LCDRST I LCD driver reset signal
18 /CS I LCD driver chip-serect signal
19 P_TEMP O Temperature detection signal
20 /KEYINT O Key state change signal
21 I2CCK I I2C serial clock
22 I2CDT I/O I2C serial data
23 GND - Ground
24 RXD O Serial data output
25 TXD I Serial data input
26 /PSW O Detection signal input of power switch
27 DM I/O MIC data detection
28 /PTT O PTT input
29 ME - MIC ground
30 MIC/VBUS O MIC signal input / USB VBUS Detection
31 NC - No connection
32 GND - Ground
33 USB_D- I/O USB0 PHY data minus
34 GND - Ground
35 USB_D+ I/O USB0 PHY data plus
36 GND - Ground
37 NC - No connection
38 18M I 1.8V input
39 NC - No connection
40 32M I 3.2V input
41 NC - No connection
42 54M I 5.4V input
43 NC - No connection
Pin No. Name I/O Function
(No.RA054<Rev.001>)1-27
2.6.4 D-Sub 15-pin Connector Specification
44 SB1 O Switched power supply
45 SB1 O Switched power supply
46 SB1 O Switched power supply
47 SB1 O Switched power supply
48 NC - No connection
49 GND - Ground
50 GND - Ground
51 GND - Ground
52 GND - Ground
53 NC - No connection
54 SP+ I Speaker input
55 SP+ I Speaker input
56 SP+ I Speaker input
57 NC - No connection
58 GND - Ground
59 GND - Ground
60 GND - Ground
Pin No. Name I/O Function
Pin No. Pin Name I/O Modification
SignalType
DescriptionRating and Condition
Parameter Min Typ Max Unit
1 SB O No Power Switched B Output Voltage This parameter depends on Battery Voltage
Supply Current - - 2.0 A
2 IGN I No Digital Active High Input Voltage Range 0 - 30 V
Threshold High 6.0 - - V
Threshold Low - 5.0 - V
3 SP2/PA O No Analog Speaker output Audio Output 3 4 - W
Coupling Capacitor - 330 - uF
RL 3.0 - - ohm
Allowable Frequency 300.0 - 3000 Hz
4 DETO O Yes Analog FM detector output Output Level - 0.24 - Vp-p
Coupling Capacitor - 10 - uF
Allowable Load - 600 - ohm
Output Impedance - 100 - ohm
AFO O RX Audio output Output Level - 0.6 - Vp-p
Coupling Capacitor - 10 - uF
Allowable Load - 600 - ohm
Output Impedance - 100 - ohm
Allowable Frequency 300 - 3000 Hz
5 DATAI I Yes Analog External Modulation input Input Voltage Range - 0.5 - Vp-p
Input Impedance - 45 - kohm
MI2 I Analog External MIC AF Input Input Voltage Range - 5.0 - mVrms
Allowable Frequency 300 - 3000 Hz
Input Impedance - 600 - ohm
1-28 (No.RA054<Rev.001>)
6 FNC1COM1_TXD
I/O Yes Digital Programmable I/O VIH 4.0 - 5.2 V
VIL -0.5 - 1.0 V
VOH(Io=-1.5mA) 4.0 - 5.2 V
VOL(Io=1.5mA) - - 1.1 V
TXD(RS-232C)
O Digital RS-232C Serial port(TXD)
Voltage Swing ±5 ±5.2 V
Baud Rate - 300k bps
7 FNC2COM1_RXD
I/O Yes Digital Programmable I/O VIH 4.0 - 5.2 V
VIL -0.5 - 1.0 V
VOH(Io=-1.5mA) 4.0 - 5.2 V
VOL(Io=1.5mA) - - 1.1 V
RXD(RS-232C)
I Digital RS-232C Serial port(RXD)
Input Voltage Range -30.0 - 30.00 V
Threshold Low 0.51 1.326 - V
Threshold High - 1.632 2.448 V
Baud Rate - - 300k bps
CL - 100 - pF
8 FNC3 I/O Yes Digital Programmable I/O VIH 4.0 - 5.2 V
VIL -0.5 - 1.0 V
VOH(Io=-1.5mA) 4.0 - 5.2 V
VOL(Io=1.5mA) - - 1.1 V
RTS(RS232C) O Digital RS-232C Serial port (RTS) Voltage Swing ±5 ±5.2 - V
9 FNC4 I/O Yes Digital Programmable I/O VIH 4.0 - 5.2 V
VIL -0.5 - 1.0 V
VOH(Io=-1.5mA) 4.0 - 5.2 V
VOL(Io=1.5mA) - - 1.1 V
CTS(RS232C)
I Digital RS-232C Serial port(CTS)
Input Voltage Range -30.0 30.00 V
Threshold Low 0.5 1.3 V
Threshold High 1.75 2.6 V
10 FNC5 I/O No Digital Programmable I/O VIH 4.0 - 5.2 V
VIL -0.5 - 1.0 V
VOH(Io=-1.5mA) 4.0 - 5.2 V
VOL(Io=1.5mA) - - 1.1 V
11 FNC6 I/O No Digital Programmable I/O VIH 4.0 - 5.2 V
VIL -0.5 - 1.0 V
VOH(Io=-1.5mA) 4.0 - 5.2 V
VOL(Io=1.5mA) - - 1.1 V
12 50AC O No Power 5V DC Power supply Output Voltage 4.5 5 5.25 V
Output Current - - 100.0 mA
13 HR1 I Yes Analog Horn alert signal input Input Voltage 5 - 16 V
Input Current - - 2.0 A
COM2_TXD O Digital TXD VOH(Io=-1.5mA) 4.0 - 5.2 V
VOL(Io=1.5mA) -0.5 - 1.0 V
Pin No. Pin Name I/O Modification
SignalType
DescriptionRating and Condition
Parameter Min Typ Max Unit
(No.RA054<Rev.001>)1-29
14 HR2 O Yes Analog Horn alert signal output Output Voltage This parameter depends on HR1 Voltage
Output Voltage Loss - - 1.0 V
Output Current - - 2.0 A
COM2_RXD I Digital RXD VIH 2.8 - 5.2 V
VIL -0.5 - 0.5 V
15 GND - No GND Ground - - - -
Pin No. Pin Name I/O Modification
SignalType
DescriptionRating and Condition
Parameter Min Typ Max Unit
1-30 (No.RA054<Rev.001>)
SECTION 3DISASSEMBLY
3.1 Disassembly Procedure
(1) Remove the cabinet, top packing and shielding plate of thetransceiver.
(2) To remove the panel assembly, first turn the transceiverupside down.Then, insert a flat-head screwdriver into the holes of thechassis and tilt it in the direction as shown by the arrow.
(3) Disconnect the flat cable from connector of the panelassembly.
(4) Remove the speaker lead from the holder hook.<1>Remove the speaker connector from the display unitconnector.<2>Insert a flat-head screwdriver at the stamp position (arrowmark) in the speaker holder.<3>
Tilt the screwdriver in the figure direction <4>, then removethe speaker holder from the front panel.
Cabinet
Holes
Panel assembly
Flat cable
<1>Holder hook<1>Holder hook
<2>Speaker connector<2>Speaker connector
<3><3><3>
Speaker holderSpeaker holder
<4><4>
(No.RA054<Rev.001>)1-31
(5) When removing the TX-RX PCB, then remove the solder ofthe antenna hot pin and positive terminal of the DC cord.Remove the 15 screws from the TX-RX PCB, powermodule,and audio amp.
(6) Pull it out behind the chassis by rotating the bush <c> of theDC cord 90 degrees in the direction of the arrow after thescrew <a> in the negative terminal is removed, and thepositive terminal <b> is removed from the chassis.
3.2 Precautions for Reassembly
(1) Push the upper tabs of speaker holder (stamped mark <1>side) into the front panel first.Then push the lower tabs (stamped mark <2> side) into thefront panel.
(2) When mounting the panel assembly, pass the flat cablethrough the hole of the chassis as shown below thenconnect the flat cable to connector of the panel assembly.
(3) Fit the panel assembly into the two tabs of the chassis topside first.Then, fit the panel assembly into the two tabs of the chassisbottom side by turning the panel assembly.
of the DC cord
Antenna hot pin
TX-RX PCB
Power module
Audio amp
Positive terminal
DC cord
a
ccb
There are stamped marks <1> or <2> on
the four corners of the speaker holder.
<2>
<1>
<2>
<1>
Panel assembly
Panelassembly
Chassis
Chassis
Hole of the chassis
1-32 (No.RA054<Rev.001>)
3.3 Precautions for Reassembly
3.3.1 Assembly Information (Sheet/Cushion)When “Main Parts” is changed (ordered), “Assembled Sheet / Cushion” should also be changed (ordered) together.The Sticker and Sheet etc are non-reusable parts. It requires the new one to get the radio’s performance after repairs.
Main Parts Assembled Sheet/ Cushion
Part Name Part Number Part Name Part Number
CHASSIS A1A-0096-00 NAME PLATE B72-2283-04
CAUTION STICKER B41-1837-04
SHEET G11-4578-04
TX-RX UNIT (NX-3720H K)TX-RX UNIT (NX-3720 E)TX-RX UNIT (NX-3820H K)TX-RX UNIT (NX-3820H K2) TX-RX UNIT (NX-3820 E)
XCA-033K-00XCA-033E-01XCA-034K-00XCA-034K-01XCA-034E-01
SHEET G11-4611-04
SHIELDING COVER F1B-0086-00
MODULE UNIT XC2-0040-10 SHIELDING COVER F10-3225-05
ILL.GUIDE B1B-0101-00 OPTI.DIFFUSER B1B-0102-00
MOUNTING J2B-0341-00 FLEX P.BOARD J8C-0018-00
PANEL ASSY A6C-0067-00 KENWOOD BADGE B4D-0044-00
CAUTION STICKER B4B-0008-00
SHIELDING CASE F10-3112-13 CONDUCTIVE CUSHION G13-2101-14
SUB UNIT XC3-050M-00 REF.SHEET B1B-0103-00
(No.RA054<Rev.001>)1-33
SECTION 4ADJUSTMENT
4.1 NX-3720H(G)/3720HK TYPE Controls
4.1.1 Preparations for checking/tuning the transceiverBefore attempting to check/tune the transceiver, connect the unitto a suitable power supply.Whenever the transmitter is turned on, the unit must beconnected to a suitable dummy load (i.e. power meter).The speaker output connector must be terminated with an 4ohmdummy load and connected to an AC voltmeter and an audiodistortion meter or a SINAD measurement meter at all timesduring checking/tuning.
4.2 Panel Test Mode
4.2.1 Test mode operation featuresThis transceiver has a test mode. To enter test mode, press andhold the [ ] button while turning the transceiver power ON orpress the [ ] button and select the "Panel Test". Before thetransceiver enters test mode, the frequency version informationappears on the LCD momentarily. Test mode can be inhibited byprogramming. To exit test mode, turn the transceiver power OFF.The following functions are available in test mode.
• When the panel test mode is activated, the last used channeland signaling numbers are displayed. When the panel testmode is activated for the first time, the channel and signalingnumbers are 1.
4.2.2 Button operation
*1: When the mode is selected as Analog, this function isenabled.
Power switch
Channel Up/Down buttonVolume Up/Down button
MIC jack
KMC-36 (OPTION)
Keypad
[PTT]
Button "Func" not appears on the sub LCD display
Function Display
[+] Push: Volume upHold: Volume up continuously
-
[-] Push: Volume downHold: Volume down continuously
-
[] Push: Test channel upHold: Test channel up continuously
Channel No.
[] Push: Test channel downHold: Test channel down continuously
Channel No.
[] Push: Squelch level up *1Hold: Squelch off
Squelch levelSquelch off: icon appears
[] Wide/Narrow/Very Narrow
Wide : "w"Narrow: "n"Very Narrow: "v"
[ ] Shift to panel tuning mode
-
[ ] Function on "Func" appears on the sub LCD display
[ ] Push: Test signaling upHold: Test signaling up continuously
Signaling No.
[ (AUX)] MSK 1200bps and 2400bps *1
2400bps: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
- -
Button "Func" appears on the sub LCD display
Function Display
[+] Function off -
[-] Function off -
[] - -
[] Mode selectionAnalog/NXDN/DMR
Analog: "A"NXDN: "N"DMR: "D"
[] Function off -
[] Button/LCD check The contents of the pressed button etc., appear.
[ ] High power/Medium power/Low power
High:[ ] icon appearsMedium:[ ] icon appearsLow:[ ] icon appears
[ ] Function off -
1-34 (No.RA054<Rev.001>)
• LED indicatorRed LED Lights during transmission.Green LED Lights when there is carrier.
• Sub LCD indicator"Func" Appears at function on.
• LCD display in panel test mode
4.2.3 Frequency and SignalingThe transceiver has been adjusted for the frequencies shown inthe following table. When required, readjust them following theadjustment procedure to obtain the frequencies you want inactual operation.
(1) Test frequency
(2) SignalingAnalog Type Signaling
[ ] External Speaker on/off
On: icon appears
[ (AUX)] Compander on/off On: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
Function off -
Button "Func" appears on the sub LCD display
Function Display
(Power ON)
Type Frequency range
136~174MHz
(After 2sec.)
Temperature [oC]Power
An : Analog narrow mode
Aw : Analog wide 5k mode
Nn : NXDN narrow mode
Nv : NXDN very narrow mode
D : DMR mode
Squelch level
(Analog mode only)
Sub LCD display
Main LCD display Signaling
No.
Channel No.
CH RX (MHz) TX (MHz)
1 155.05000 155.10000
2 136.05000 136.10000
3 173.95000 173.90000
4 155.00000 155.00000
5 155.20000 155.20000
6 155.40000 155.40000
7~16 - -
No. RX TX
1 None None
2 None Square Wave
3 LTR Data LTR Data
4 QT:67.0Hz QT:67.0Hz
5 QT:151.4Hz QT:151.4Hz
6 QT:210.7Hz QT:210.7Hz
7 QT:254.1Hz QT:254.1Hz
8 DQT:D023N DQT:D023N
9 DQT:D754I DQT:D754I
10 DTMF Decode (CODE: 159D)
DTMF Encode (CODE: 159D)
11 None DTMF Encode (CODE: 9)
12 2-tone Decode (A: 304.7Hz, B: 3106.0Hz)
2-tone Encode (A: 304.7Hz,B: 3106.0Hz)
13 Single Tone Decode (979.9Hz)
Single Tone Encode (979.9Hz)
14 None Single Tone Encode (1000Hz)
15 None MSK PN9
16 MSK Decode MSK Encode
(No.RA054<Rev.001>)1-35
NXDN Type Signaling
RAN: Radio Access NumberPN9: Pseudo-Random PatternNo.7, 9 Item: PC test mode only
DMR Type Signaling
4.3 Panel Tuning Mode4.3.1 Transceiver tuning (To enter tuning mode)To enter tuning mode, press the [ ] button while the transceiveris in test mode. Use the [ (AUX)] button to write tuning datathrough tuning modes, and the [ ]/[ ] button to adjust tuningrequirements (1 to 4096 appears on the LCD).Use the [ ] button to select the adjustment item through tuningmodes. Use the [ ] button to adjust 5 or 9 reference leveladjustments, and use the [ ] button to switch between Wide/Narrow.
• LCD display in panel tuning mode
4.3.2 Button operation
4.3.3 5 or 9 reference level adjustments frequencyMaximum Transmit Power, High Transmit Power, MediumTransmit Power, Low Transmit Power, Balance, MaximumDeviation, NXDN High Deviation, DMR High Deviation, QTDeviation, DQT Deviation, LTR Deviation, DTMF Deviation,Single Tone Deviation, MSK Deviation, CW ID Deviation, IQPhase, RSSI Reference, Squelch Open, Squelch Tight, LowRSSI, High RSSI
No. RX TX
1 RAN1 RAN1
2 None PN9
3 RAN1 Maximum Deviation Pattern
7 FSW + PN9 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
No. RX TX
1 CC 00 Burst CC 00 Burst
2 PN9 PN9
3 CC 00 Burst Maximum Deviation Pattern
4 CC 00 Burst 1/3 Deviation Pattern
5 CC 00 Burst 0 Continuous Pattern
6 SYNC (Each Slot) +PN9 Burst Pattern
SYNC (Each Slot) + PN9Burst Pattern
7 SYNC (Super Frame) +PN9 Burst Pattern
SYNC (Super Frame) +PN9 Burst Pattern
8 CC 00 Burst 0 Burst Pattern
9 Tone Pattern Tone Test Burst Pattern
10 Silence Pattern Silence Burst Pattern
11 Audio Test Pattern Audio Test Burst Pattern
12 Vocoder Loop None
An AST 2562.6
CV voltage, AD value, etc
Sub LCDdisplay
L1
Adjustment point
Main LCDdisplay Adjustment value
(1~4096)
Proper value guide(When the frequency adjustment is necessary,
or is displayed.)
Adjustment item
An : Analog narrow modeAw : Analog wide 5k modeAs : Analog wide 4k mode *1Nn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
L1L2L3
C1C2C3
H1H2H3
*1: Wide 4k is displayed only when the PC test mode is used. However, it aims at production for factory, or a operation verification of the transceiver. It is not necessary in operation of the transceiver to adjust.
Button Function
Push Hold (1 second)
[+] Volume up Continuation up
[-] Volume down Continuation down
[ ] Adjustment value up Continuation up
[ ] Adjustment value down Continuation down
[ ] Auto adjustment start Output tone pattern change of balance adjustment (A change is possible only during balance adjustment.)
[ ] Wide/Narrow/NXDN/DMR
-
[ ] Shift to panel test mode -
[ ] To enter 5 or 9 reference level adjustments
-
[ ] Go to next adjustment item
Back to last adjustment item (At the time of 5 or 9 point adjustment: Adjustment point change)
[ (AUX)] Writes the adjustmentvalue
-
[PTT](MIC)
Transmit
[0] to [9]and[#],[ ](MIC)
-
Tuning point Display RX (MHz) TX (MHz)
1 L1 136.05000 136.10000
2 L3 145.55000 145.60000
3 C2 155.05000 155.10000
4 H1 164.55000 164.60000
5 H3 173.95000 173.90000
1-36 (No.RA054<Rev.001>)
VCO Assist
4.3.4 Adjustment item supplement
Tuning point Display RX (MHz) TX (MHz)
1 L1 136.05000 136.10000
2 L2 140.80000 140.85000
3 L3 145.55000 145.60000
4 C1 150.30000 150.35000
5 C2 155.05000 155.10000
6 C3 159.80000 159.85000
7 H1 164.55000 164.60000
8 H2 169.30000 169.35000
9 H3 173.95000 173.90000
Adjustment Item Description
LCD Contrast The contrast of LCD display can be changed.
VCO Assist The lock voltage of VCO is adjusted.This item must be adjusted before receiver and transmitter adjustment items.
Frequency Frequency is adjusted under receivingcondition with SSG.The SSG needs 0.001ppm accuracy soplease use a standard oscillator if necessary.This item can be adjusted only in PC TestMode so that the adjustment value is notchanged easily.
RTC Correction Real Time Clock is adjusted.This item uses the internal clock.(Any measurement equipment is not required.)
Maximum Transmit Power
Maximum Transmit Power is adjusted.
High Transmit Power
High Transmit Power is adjusted.
Mid Transmit Power
Medium Transmit Power is adjusted.
Low Transmit Power
Low Transmit Power is adjusted.
Ramp Offset Adjust this item to the optimal Ramp voltage.
Balance The transmit modulation frequency response is adjusted.This item is adjusted so that the deviationof 2kHz becomes the same deviation of 20Hz.This item must be adjusted before all adjustment items for deviations are adjusted.
Maximum Deviation(Analog Wide 5k/Wide 4k/Narrow)
Maximum Deviation of Analog (Wide 5k/Wide 4k/Narrow) is adjusted.This item must be adjusted before all adjustment items for tone deviations are adjusted.
High Deviation NXDN/DMR high deviation is adjusted.
QT Deviation QT deviation is adjusted.
DQT Deviation DQT deviation is adjusted.
LTR Deviation LTR deviation is adjusted.
DTMF Deviation DTMF deviation is adjusted.
Single Tone Deviation
The deviation of Single Tone used in “2-tone” and “5-tone” is adjusted.
MSK Deviation MSK deviation is adjusted.
CW ID Deviation CWID tone deviation is adjusted.CWID is used to inform the others who istransmitting on a 6.25-kHz spacing channel.(In FCC rule, Analog mode or CWID isrequired for each channel-spacing.)
IQ Phase Correction of phase difference shift between I and Q.
RSSI Reference The minimum RSSI level for scan stop isadjusted.
Squelch Open The squelch level at level “1” is adjusted.
Squelch Tight The squelch level at level “9” is adjusted.
Low RSSI RSSI display level “ ” is adjusted.Both “Low RSSI” and “High RSSI” must beadjusted. (The curve data of RSSI level isapplied.)
High RSSI
Adjustment Item Description
(No.RA054<Rev.001>)1-37
4.3.5 Adjustment item and Display
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide)
AS *2(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1 LCD Contrast CNTR - 1 point ADJ CommonSection 21~256
2 VCO Assist AST (CV voltage) - - 9 - - - CommonSection 31~4096
3 RTC Correction RTC - - CommonSection 5-2.00 ~ -0.01 ,0.00 ,+0.01 ~ +2.00
4 Maximum Transmit Power
MAX_P - - - 5 - - - TransmitterSection 11~256
5 High Transmit Power
H_PWR - - - 5 - - - TransmitterSection 21~1024
6 Medium Transmit Power
M_PWR - - - 5 - - - TransmitterSection 31~1024
7 Low Transmit Power
L_PWR - - - 5 - - - TransmitterSection 41~1024
8 Ramp Offset RAMP (ADC measurement value)
1 point ADJ TransmitterSection 51~1024
9 Balance BAL (Encode frequency) - - 5 - - - TransmitterSection 61~1024
10 Maximum Deviation
ADEV - 5 5 *2 5 - - - TransmitterSection 71~1024
11 NXDN High Deviation
NDEV - - - - 5 5 - TransmitterSection 81~1024
12 DMR High Deviation
DDEV - - - - - - 5 TransmitterSection 91~1024
13 QT Deviation QT - 5 5 *2 5 - - - TransmitterSection 101~1024
14 DQT Deviation DQT - 5 5 *2 5 - - - TransmitterSection 111~1024
15 LTR Deviation LTR - 5 5 *2 5 - - - TransmitterSection 121~1024
16 DTMF Deviation DTMF - 5 5 *2 5 - - - TransmitterSection 131~1024
17 Single Tone Deviation
TONE - 5 5 *2 5 - - - TransmitterSection 141~1024
18 MSK Deviation MSK - 5 5 *2 5 - - - TransmitterSection 151~1024
19 CW ID Deviation CWID - - - 5 - - - TransmitterSection 161~1024
20 IQ Phase IQ (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 21~63
21 RSSI Reference 1 DSP (Receive)
RSSI1 (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
1-38 (No.RA054<Rev.001>)
*2: Wide 4k can be set up only when the PC test mode is used.
22 RSSI Reference 2 RF IC(Receive)
RSSI2 (RSSI RF IC(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
23 RSSI Reference 3 DSP (Standby)
RSSI3 (RSSI DSP (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
24 RSSI Reference 4 RF IC (Standby)
RSSI4 (RSSI RF IC (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
25 Squelch Open SQL (ASQDET measurement value)
5 5 *2 5 5 5 5 ReceiveSection 41~256
26 Squelch Tight SQLT (ASQDET measurement value)
5 5 *2 5 - - - ReceiveSection 51~256
27 Low RSSI LRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 61~256
28 High RSSI HRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 71~256
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide)
AS *2(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
(No.RA054<Rev.001>)1-39
4.3.6 Panel tuning mode flow chartNote:
* In this Panel tuning mode flow chart, the Adjustment item name is modified.
SQL An SQL Aw SQL Nn
Squelch (Open) Narrow Squelch (Open) Wide Squelch (Open) Narrow
Max PowerMAX_P
Panel Test Mode
[ ]hold
LCD Contrast
CNTR
levelecnerefer9VCO Assist
stnemtsujdAAST
RTC Correction
RTC
Ramp Offset
RAMP
High Power Narrow 5 reference level
H_PWR An Adjustments
Medium Power Narrow 5 reference level
M_PWR An Adjustments
Low Power Narrow 5 reference level
L_PWR An Adjustments
Balance Narrow 5 reference level
BAL An Adjustments
Analog Max Deviation Narrow Analog Max Deviation Wide
ADEV An ADEV Aw
5 reference level
Adjustments
5 reference level
Adjustments
5 reference level
Adjustments
NXDN High Deviation Narrow NXDN High Deviation VeryNarrow
NDEV Nn NDEV Nv
QT Deviation Narrow QT Deviation Wide
wATQnATQ
5 reference level
Adjustments
DQT Deviation Narrow DQT Deviation Wide
DQT An DQT Aw
5 reference level
Adjustments
LTR Deviation Narrow LTR Deviation Wide
wARTLnARTL
5 reference level
Adjustments
DTMF Deviation Narrow DTMF Deviation Wide
DTMF An DTMF Aw
5 reference level
Adjustments
MSK Deviation Narrow MSK Deviation Wide
MSK An MSK Aw
5 reference level
Adjustments
CW ID Deviation Narrow
CWID An
Squelch (Open) DMR
5 reference level
Adjustments
RSSI (Low) Narrow
nAISSRL
RSSI (High) Narrow
nAISSRH
Adjustment Item N/W/VN
LCD Display
For all adjustment items, press the [ ] button
to write the adjustment value.
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ] [ ] [ ] [ ] [ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]
5 reference level
Adjustments
Narrow
An
[ ]
5 reference level
Adjustments
[ ]
RSSI Referance 1
RSSI1[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]IQ Phase
IQ[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 2
RSSI2[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 3
RSSI3[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 4
RSSI4[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
Single Tone Deviation Narrow Single Tone Deviation Wide
TONE An TONE Aw
5 reference level
Adjustments
[ ] [ ][ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
DMR High Deviation
DDEV
[ ]press [ ]hold
[ ]
[ ] [ ] [ ]
Adjustment Point
LCD Display
5 reference level
L1
L3
C2
H3
H1
Low 1
Adjustments
Low 3
Center 2
High 3
5 reference level
Adjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]High 1 [ ]
[ ]
[ ]
High Transmit Power
Maximum Transmit Power
Medium Transmit Power
Low Transmit Power
Maximum Deviation
NXDN High Deviation
DMR High DeviationQT Deviation
DQT Deviation
LTR Deviation
DTMF Deviation
Single Tone Deviation
MSK Deviation
CW ID Deviation
IQ Phase
RSSI Reference 1
RSSI Reference 2
RSSI Reference 3
RSSI Reference 4
Open Squelch
Low RSSI
High RSSI
Tight Squelch
Adjustment Point
LCD Display
9 reference level
L1
L2
L3
H3
C1
C2
C3
H1
H2
Low 1
Adjustments
Low 2
Low 3
High 3
9 reference level
Adjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Center 1 [ ]
[ ]
Center 2
Center 3
[ ]
[ ][ ]
[ ]High 1 [ ]
[ ]
High 2 [ ]
[ ]
[ ]
Balance
VCO Assist
VeryNarrow
Squelch (Tight) Narrow Squelch (Tight) Wide
wATLQSnATLQS
5 reference level
Adjustments
[ ] [ ][ ]press [ ]hold
[ ] [ ]
TLSn
5 reference level
Adjustments
[ ] [ ][ ]press [ ]hold
[ ] [ ]
[ ]press [ ]hold
DMR
D
Squelch (Open)
Nv D
[ ]
5 reference level
Adjustments
[ ]
5 reference level
Adjustments
[ ]
1-40 (No.RA054<Rev.001>)
4.4 Adjustment point
TX-RX UNIT (XC1-182)Component Side
4.5 Test Equipment Required for Alignment
*The test equipment which is not used for adjustment is contained in this table.
RTC (CN55)
RT
C
Test Equipment Major Specifications
1. Standard Signal Generator (SSG)
Frequency RangeModulation Output
100 to 900MHzFrequency modulation and external modulation-127dBm/0.1uV to greater than -20dBm/22.4mV
When performing the Frequency adjustment, the following accuracy is necessary.• 0.003ppmUse a standard oscillator for adjustments, if necessary.
2. Power Meter Input ImpedanceOperation FrequencyMeasurement Capability
50ohm100 to 900MHzVicinity of 100W
3. Deviation Meter Frequency Range 100 to 900MHz
4. Digital Volt Meter (DVM)
Measuring RangeInput Impedance
10mV to 20V DCHigh input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. Frequency Counter Frequency RangeFrequency Stability
10Hz to 1000MHz0.2ppm or less
To measure the oscillating frequency of the internal clock 32766.00Hz~32770.00Hz forRTC Correction Resolution 0.01Hz is better for accuracy adjustment.
7. Ammeter 20A or more
8. AF Volt Meter (AF VM) Frequency RangeVoltage Range
50Hz to 10kHz1mV to 10V
9. Audio Generator (AG) Frequency RangeOutput
50Hz to 5kHz or more0 to 1V
10. Distortion Meter CapabilityInput Level
3% or less at 1kHz50mV to 10Vrms
11. Spectrum Analyzer Measuring Range DC to 1GHz or more
12. 4ohm Dummy Load Approx. 4ohm, 10W
13. Regulated Power Supply 13.6V, approx. 20A (adjustable from 9V to 17V)Useful if ammeter equipped
(No.RA054<Rev.001>)1-41
Test cable for microphone input (E30-3360-28) MIC connector (Front panel view)
Tuning cable (E30-7754-05)Adapter cable (E30-7754-05) is required for injecting an audioif PC tuning is used.See “PC Mode” section for the connection.
4.6 Radio check Section
3
2
4
5
6
7
8
3
1
2
4
5
6
7
8
1GREEN
RED
BLACK
BLUE
SHIELD
WHITE
GRAY
YELLOW
PTT
E
MIC-E
MIC
HK
1 : BLC
2 : +B
3 : GND
4 : PTT/TXD (PC serial data from radio)
5 : MICE
6 : MIC
7 : HOOK/RXD (PC serial data to radio)
8 : DM
1
8
Item Condition Measurement Adjustment Specifications/RemarksPanel test
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Frequency check
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
f. counter Panel ANT Check an internal temperature of radio from 20°C to 33°C.
±0.25ppm±[email protected]
2. High power check
1)CH-Sig: 1-1PTT: ONTA: OFF
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 45W~55W13.0A or less
2)CH-Sig: 2-1PTT: ONTA: OFF
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ONTA: OFF
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
1-42 (No.RA054<Rev.001>)
3.Mediumpowercheck
1)CH-Sig: 1-1PTT: ONTA: OFF
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 25W~35W10A or less
2)CH-Sig: 2-1PTT: ONTA: OFF
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ONTA: OFF
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
4. Low power check
1)CH-Sig: 1-1PTT: ONTA: OFF
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 3.5W~6.5W7.0A or less
2)CH-Sig: 2-1PTT: ONTA: OFF
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ONTA: OFF
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
5. MIC sensitivity check
1)CH-Sig: 1-1AG: 1kHzPTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1AG: 1kHzPTT: Press [Transmit] button.
DeviationmeterOscilloscopeAGAF VM
Panel ANTMIC jack
Adjust AGinput to get astandardMOD.
5mV ±1mV
Item Condition Measurement Adjustment Specifications/RemarksPanel test
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-43
4.7 Common Section
6. Sensitivitycheck
1)CH-Sig: 1-1SSG outputWide: -117dBm(0.32μV)(MOD: 1kHz/±3kHz)Narrow: -117dBm(0.32μV)(MOD: 1kHz/±1.5kHz)
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG outputWide: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
SSGAF VMOscilloscopeDistortionmeter4ohmDummy load
Panel ANTExt. SPconnector
Check 12dB SINAD or more
Item Condition Measurement Adjustment Specifications/RemarksPanel test
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Setting
1) DC voltage:13.6V2) SSG standard modulation
[Wide] MOD:1kHz,DEV:3kHz[Narrow] MOD:1kHz,DEV:1.5kHz
2.LCD Contrast
1) Adj item[CNTR]Adjust:[****]
Press [ ] button to store the adjustment value.
1) Adj item[LCD Contrast]Data: [****]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.
280 (Reference value)
3. VCO Assist
1) Adj item:[AST]Adjust:[****]2) Adj item:[L1]→[L2]→[L3]→[C1]→[C2]→[C3]→[H1]→[H2]→[H3]→
Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [VCO Assist]2) Adj item:[Low1],[Low2], [Low3], [Center1], [Center2], [Center3], [High1],[High2][High3]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment][V] Indicator on the PC window shows VCO lock voltage. Change the adjustment value to get VCO lock voltage within the limit of the specified voltage.
Note:Confirm the VCO lock voltage approximately 3 seconds after the adjustment value is changed.
2.5V±0.1V[Automatic Adjustment]After the automatic adjustment is performed, verify that the VCO lock voltage is within the voltage range which is specified by the manual adjustment.[Manual Adjustment]Press [Apply] button to store the adjustment value after all adjustment points have been adjusted.Adjustment value range: 300 - 3000
1-44 (No.RA054<Rev.001>)
4.8 Transmitter Section
4. Frequency
*The Frequency adjustment can be performed only in PC test mode.
1) Adj item: [Frequency]SSG output: -20dBm (22.4mV) (CW (without modulation))
Caution:Perform the frequency adjustment under the following conditions.
• Temperature range of +20°C to +33°C (+68.0°F to +91.4°F).(The temperature is displayed on the Frequency adjustment screen of the KPG-D3/D3N and the LCD of the transceiver.)
• Use an accuracy of 0.003ppm for the SSG. (Use a standard oscillator if necessary.)
SSG Panel ANT [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode]Press [Start] button of “Auto Tuning”. Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
[PC test mode]“IF20” value = Within 0±10 digits. The value of “IF20” will become around “0” after the adjustment has finished.
Remark:“Frequency” is adjusted under receiving condition with SSG.
5. RTC Correciton
1) Adj item:[RTC]Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [RTC Correction]Data: [****]Press [Apply] button to store the adjustment value.
Frequency Counter
TX-RX
TESTPOINT(CN55)
Remark:The adjustment value should input the display of a Frequency Counter.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1.MaximumTransmitPower
1) Adj item:[MAX_P]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maximum Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
57.5W ±2.5W15A or less
(No.RA054<Rev.001>)1-45
2. High Transmit power
1) Adj item:[H_PWR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [High Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
50W ±1W 13A or less
3. Medium Transmit power
1) Adj item:[M_PWR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Medium Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
30W ±1W 10A or less
4. Low Transmit power
1) Adj item:[L_PWR]
Adjust:[****]2) Adj item:
[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Low Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
5W ±0.5W 7A or less
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-46 (No.RA054<Rev.001>)
5.Ramp Offset
1)Adj item:[RAMP]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Ramp Offset]Press [Autotune(TX Starts)] button. Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune(TX
starts)] button.2) Press [Apply] button
to store the adjustment value after the automatic adjustment has finished.
3) Check Ramp Offset Monitor Value Over 60.
[Manual Adjustment]1) Set the adjustment
value to "1".2) Press [Transmit]
button and increase the adjustment value slowly while monitoring the offset monitor value.
3) Set the adjustment value when the offset monitor value exceed "75".
6. Balance
1) Adj item: [An BAL]Adjust:[****]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Balance]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
The Deviation of 20Hz frequency is fixed.Change the 2kHz adjustment value to become the same deviation of 20Hz within the specified range.[Panel tuning mode]PTT:ONWhile PTT:ON, press the [] button to change the 20Hz/2kHz.[PC test mode]PTT: Press [Transmit] button.While PTT:ON, click the check box "2kHz Sine Wave" to change the 20Hz/2kHz.
2kHz Tone deviation is within ± 1.0% of 20Hz tone deviation.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-47
7. Maximum Deviation
[Analog Wide]
1) Adj item: [Aw ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point.(The value is written below.)Transmit at each adjustment point and check that the deviation is between 4150Hz and 4250Hz.Deviation meterLPF: 15kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
4150~4250Hz
[Analog Narrow]
1) Adj item: [An ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point.(The value is written below.)Transmit at each adjustment point and check that the deviation is between 2050Hz and 2150Hz. Deviation meterLPF: 15kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2050~2150Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-48 (No.RA054<Rev.001>)
8. NXDN High Deviation[NXDN Narrow]
1) Adj item: [Nn NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point.(The value is written below.)Transmit at each adjustment point and check that the Analog deviation is between 2995Hz and 3117Hz.Deviation meterLPF: 3kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2995~3117Hz
[NXDN Very Narrow]
1) Adj item: [Nv NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Very Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Write fixed value for each adjustment point.(The value is written below.)Transmit at each adjustment point and check that the Analog deviation is between 1311Hz and 1363Hz.Deviation meterLPF: 3kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
1311~1363Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-49
9. DMR High Deviation
1) Adj item: [D DDEV]Adjust: [****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DMR High Deviation (DMR Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Write fixed value for each adjustment point.(The value is written below.)Transmit at each adjustment point and check that the Analog deviation is between 2695Hz and 2803Hz.Deviation meterLPF: 3kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2695~2803Hz
10. QT Deviation
[Analog Wide]
1) Adj item: [Aw QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
0.75kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
0.35kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-50 (No.RA054<Rev.001>)
11. DQT Deviation
[Analog Wide]
1) Adj item: [Aw DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.430 (Reference value)
0.75kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.430 (Reference value)
0.35kHz±0.05kHz
12. LTR Deviation
[Analog Wide]
1) Adj item: [Aw LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
1.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-51
[Analog Narrow]
1) Adj item: [An LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
0.75kHz±0.05kHz
13. DTMF Deviation
[Analog Wide]
1) Adj item: [Aw DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.555 (Reference value)
2.50kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.555 (Reference value)
1.25kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-52 (No.RA054<Rev.001>)
14. Single Tone Deviation
[Analog Wide]
1) Adj item: [Aw TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
3.00kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
1.50kHz±0.05kHz
15. MSK Deviation
[Analog Wide]
1) Adj item: [Aw MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
3.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-53
[Analog Narrow]
1) Adj item: [An MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
1.50kHz±0.05kHz
16. CWID Deviation
[Analog Narrow]
1) Adj item: [An CWID]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [CWID Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
1.10kHz±0.10kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-54 (No.RA054<Rev.001>)
4.8.1 Necessary Deviation adjustment item for each signaling and modeThe following shows the necessary adjustment items for each signaling deviation. Please read the following table like the followingexample. In the case of the signaling "QT (Analog Wide)", this signaling is composed of three elements [Balance, Maximum Deviation(Analog Wide) and QT Deviation (Analog Wide)]. Please adjust Balance and Maximum Deviation (Analog Wide) before adjusting QTDeviation (Analog Wide).
• Balance is common with all the above deviation adjustments. If Balance (Transmitter Section 6) has already adjusted, please skipStep1 and adjust from Step2.
• Maximum Deviation (Analog Wide/Narrow) is common with all the analog signaling deviations and CWID Deviation (NXDN VeryNarrow).If Balance and Maximum Deviation (Analog Wide /Narrow) (Transmitter Section 7) have already adjusted, please skip Step2 andadjust from Step3.
Mode Signaling Necessary adjustment and order
Wide Narrow Very Narrow
Analog Audio 1. Balance adjust2. Maximum Deviation
[Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]
-
QT 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. QT Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. QT Deviation [Analog Narrow]
-
DQT 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. DQT Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DQT Deviation
[Analog Narrow]
-
LTR 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. LTR Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. LTR Deviation [Analog Narrow]
-
DTMF 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. DTMF Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DTMF Deviation [Analog Narrow]
-
2TONE 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. Single Tone Deviation [Analog
Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. Single Tone Deviation
[Analog Narrow]
-
MSK(Fleetsync)
1. Balance adjust2. Maximum Deviation
[Analog Wide]3. MSK Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. MSK Deviation
[Analog Narrow]
-
NXDN Audio - 1. Balance adjust2. NXDN High Deviation
[NXDN Narrow]
1. Balance adjust2. NXDN High Deviation
[NXDN Very Narrow]
CWID - - 1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. CWID Deviation
[Analog Narrow]
DMR Audio - 1. Balance adjust2. DMR High Deviation
-
(No.RA054<Rev.001>)1-55
4.9 Receiver Section
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. AF level setting
[Panel test mode]1) CH-Sig: 1-1
SSG output: -47dBm (1mV)(MOD: 1kHz/±1.5kHz)
1) Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG output: -47dBm (1mV) (MOD:1kHz/±1.5kHz)
SSGDVMAF VMDummy load
Panel ANTExt. SP connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Volume Up/Down knob to obtain 1.41V AF output.(0.5W @ 4ohm load)
1.41V±0.1V
2. IQ Phase
1) Adj item: [An IQ]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
1) Adj item: [IQ Phase]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]After input signal from SSG,1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment]Adjust RSSI Level(DSP Normal Power Mode)Value to the minimum.
3. RSSI reference [DSP (Receive)]
1) Adj item: [An RSSI 1]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 1 DSP (Receive)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Receive)]
1) Adj item: [An RSSI 2]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 2 RF IC (Receive)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
1-56 (No.RA054<Rev.001>)
[DSP (Standby)]
1) Adj item: [An RSSI 3]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 3 DSP (Standby)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Standby)]
1) Adj item: [An RSSI 4]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 4 RF IC (Standby)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
4. Squelch Open
[Analog Wide]
1) Adj item: [Aw SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Open (Analog Wide)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-57
[Analog Narrow]
1) Adj item: [An SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Open (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[NXDN Narrow]
1) Adj item: [Nn SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[NXDN Very Narrow]
1) Adj item: [Nv SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Very Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-58 (No.RA054<Rev.001>)
[DMR] 1) Adj item: [D SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
1) Adj item: [Squelch Open (DMR)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
5. Squelch Tight
[Analog Wide]
1) Adj item: [Aw SQLT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Tight (Analog Wide)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQLT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Tight (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-59
6. Low RSSI
1) Adj item: [An LRSSI]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [Low RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
7. High RSSI
1) Adj item: [An HRSSI]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [High RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-60 (No.RA054<Rev.001>)
4.10 NX-3720(G)/3720E TYPE Controls
4.10.1 Preparations for checking/tuning the transceiverBefore attempting to check/tune the transceiver, connect the unitto a suitable power supply.Whenever the transmitter is turned on, the unit must beconnected to a suitable dummy load (i.e. power meter).The speaker output connector must be terminated with an 4ohmdummy load and connected to an AC voltmeter and an audiodistortion meter or a SINAD measurement meter at all timesduring checking/tuning.
4.11 Panel Test Mode
4.11.1 Test mode operation featuresThis transceiver has a test mode. To enter test mode, press andhold the [ ] button while turning the transceiver power ON orpress the [ ] button and select the "Panel Test". Before thetransceiver enters test mode, the frequency version informationappears on the LCD momentarily. Test mode can be inhibited byprogramming. To exit test mode, turn the transceiver power OFF.The following functions are available in test mode.
• When the panel test mode is activated, the last used channeland signaling numbers are displayed. When the panel testmode is activated for the first time, the channel and signalingnumbers are 1.
4.11.2 Button operation
*1: When the mode is selected as Analog, this function isenabled.
Power switch
Channel Up/Down buttonVolume Up/Down button
MIC jack
KMC-36 (OPTION)
Keypad
[PTT]
Button "Func" not appears on the sub LCD display
Function Display
[+] Push: Volume upHold: Volume up continuously
-
[-] Push: Volume downHold: Volume down continuously
-
[] Push: Test channel upHold: Test channel up continuously
Channel No.
[] Push: Test channel downHold: Test channel down continuously
Channel No.
[] Push: Squelch level up *1Hold: Squelch off
Squelch levelSquelch off: icon appears
[] Wide 5k/Wide 4k/Narrow/Very Narrow
Wide 5k: "w"Wide 4k: "s"Narrow: "n"Very Narrow: "v"
[ ] Shift to panel tuning mode
-
[ ] Function on "Func" appears on the sub LCD display
[ ] Push: Test signaling upHold: Test signaling up continuously
Signaling No.
[ (AUX)] MSK 1200bps and 2400bps *1
2400bps: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
- -
Button "Func" appears on the sub LCD display
Function Display
[+] Function off -
[-] Function off -
[] - -
[] Mode selectionAnalog/NXDN/DMR
Analog: "A"NXDN: "N"DMR: "D"
[] Function off -
[] Button/LCD check The contents of the pressed button etc.,appear.
[ ] High power/Medium power/Low power
High:[ ] icon appearsMedium:[ ] icon appearsLow:[ ] icon appears
[ ] Function off -
[ ] External Speaker on/off On: icon appears
(No.RA054<Rev.001>)1-61
• LED indicatorRed LED Lights during transmission.Green LED Lights when there is carrier.
• Sub LCD indicator"Func" Appears at function on.
• LCD display in panel test mode
4.11.3 Frequency and SignalingThe transceiver has been adjusted for the frequencies shown inthe following table. When required, readjust them following theadjustment procedure to obtain the frequencies you want inactual operation.
(1) Test frequency
(2) SignalingAnalog Type Signaling
[ (AUX)] Compander on/off On: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
Function off -
Button "Func" appears on the sub LCD display
Function Display
(Power ON)
Type Frequency range
136~174MHz
(After 2sec.)
Temperature [oC]Power
An : Analog narrow mode
Aw : Analog wide 5k mode
As : Analog wide 4k mode
Nn : NXDN narrow mode
Nv : NXDN very narrow mode
D : DMR mode
Squelch level
(Analog mode only)
Sub LCD display
Main LCD display Signaling
No.
Channel No.
CH RX (MHz) TX (MHz)
1 155.05000 155.10000
2 136.05000 136.10000
3 173.95000 173.90000
4 155.00000 155.00000
5 155.20000 155.20000
6 155.40000 155.40000
7~16 - -
No. RX TX
1 None None
2 None Square Wave
3 LTR Data LTR Data
4 QT:67.0Hz QT:67.0Hz
5 QT:151.4Hz QT:151.4Hz
6 QT:210.7Hz QT:210.7Hz
7 QT:254.1Hz QT:254.1Hz
8 DQT:D023N DQT:D023N
9 DQT:D754I DQT:D754I
10 DTMF Decode (CODE: 159D)
DTMF Encode (CODE: 159D)
11 None DTMF Encode (CODE: 9)
12 2-tone Decode (A: 304.7Hz, B: 3106.0Hz)
2-tone Encode (A: 304.7Hz,B: 3106.0Hz)
13 Single Tone Decode (979.9Hz)
Single Tone Encode (979.9Hz)
14 None Single Tone Encode (1000Hz)
15 None MSK PN9
16 MSK Decode MSK Encode
1-62 (No.RA054<Rev.001>)
NXDN Type Signaling
RAN: Radio Access NumberPN9: Pseudo-Random PatternNo.7, 9 Item: PC test mode only
DMR Type Signaling
4.12 Panel Tuning Mode
4.12.1 Transceiver tuning (To enter tuning mode)To enter tuning mode, press the [ ] button while the transceiveris in test mode. Use the [ (AUX)] button to write tuning datathrough tuning modes, and the [ ]/[ ] button to adjust tuningrequirements (1 to 4096 appears on the LCD).Use the [ ] button to select the adjustment item through tuningmodes. Use the [ ] button to adjust 5 or 9 reference leveladjustments, and use the [ ] button to switch between Wide5k/Wide4k/Narrow.
• LCD display in panel tuning mode
4.12.2 Button operation
4.12.3 5 or 9 reference level adjustments frequencyMaximum Transmit Power, High Transmit Power, MediumTransmit Power, Low Transmit Power, Balance, MaximumDeviation , NXDN High Deviation, DMR High Deviation, QTDeviation, DQT Deviation, LTR Deviation, DTMF Deviation,Single Tone Deviation, MSK Deviation, CW ID Deviation, IQPhase, RSSI Reference, Squelch Open, Squelch Tight, LowRSSI, High RSSI
No. RX TX
1 RAN1 RAN1
2 None PN9
3 RAN1 Maximum Deviation Pattern
7 FSW + PN9 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
No. RX TX
1 CC 00 Burst CC 00 Burst
2 PN9 PN9
3 CC 00 Burst Maximum Deviation Pattern
4 CC 00 Burst 1/3 Deviation Pattern
5 CC 00 Burst 0 Continuous Pattern
6 SYNC (Each Slot) +PN9 Burst Pattern
SYNC (Each Slot) + PN9Burst Pattern
7 SYNC (Super Frame) +PN9 Burst Pattern
SYNC (Super Frame) +PN9 Burst Pattern
8 CC 00 Burst 0 Burst Pattern
9 Tone Pattern Tone Test Burst Pattern
10 Silence Pattern Silence Burst Pattern
11 Audio Test Pattern Audio Test Burst Pattern
12 Vocoder Loop None
An AST 2562.6
CV voltage, AD value, etc
Sub LCDdisplay
L1
Adjustment point
Main LCDdisplay Adjustment value
(1~4096)
Proper value guide(When the frequency adjustment is necessary,
or is displayed.)
Adjustment item
An : Analog narrow modeAw : Analog wide 5k modeAs : Analog wide 4k modeNn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
L1L2L3
C1C2C3
H1H2H3
Button Function
Push Hold (1 second)
[+] Volume up Continuation up
[-] Volume down Continuation down
[ ] Adjustment value up Continuation up
[ ] Adjustment value down Continuation down
[ ] Auto adjustment start Output tone pattern change of balance adjustment (A change is possible only during balance adjustment.)
[ ] Wide 5k/Wide 4k/Narrow/NXDN/DMR
-
[ ] Shift to panel test mode -
[ ] To enter 5 or 9 reference level adjustments
-
[ ] Go to next adjustment item
Back to last adjustment item (At the time of 5 or 9 point adjustment: Adjustment point change)
[ (AUX)] Writes the adjustmentvalue
-
[PTT](MIC)
Transmit
[0] to [9]and[#],[ ](MIC)
-
Tuning point Display RX (MHz) TX (MHz)
1 L1 136.05000 136.10000
2 L3 145.55000 145.60000
3 C2 155.05000 155.10000
4 H1 164.55000 164.60000
5 H3 173.95000 173.90000
(No.RA054<Rev.001>)1-63
VCO Assist
4.12.4 Adjustment item supplement
Tuning point Display RX (MHz) TX (MHz)
1 L1 136.05000 136.10000
2 L2 140.80000 140.85000
3 L3 145.55000 145.60000
4 C1 150.30000 150.35000
5 C2 155.05000 155.10000
6 C3 159.80000 159.85000
7 H1 164.55000 164.60000
8 H2 169.30000 169.35000
9 H3 173.95000 173.90000
Adjustment Item Description
LCD Contrast The contrast of LCD display can be changed.
VCO Assist The lock voltage of VCO is adjusted.This item must be adjusted before receiver and transmitter adjustment items.
Frequency Frequency is adjusted under receivingcondition with SSG.The SSG needs 0.001ppm accuracy soplease use a standard oscillator if necessary.This item can be adjusted only in PC TestMode so that the adjustment value is notchanged easily.
RTC Correction Real Time Clock is adjusted.This item uses the internal clock.(Any measurement equipment is not required.)
Maximum Transmit Power
Maximum Transmit Power is adjusted.
High Transmit Power
High Transmit Power is adjusted.
Mid Transmit Power
Medium Transmit Power is adjusted.
Low Transmit Power
Low Transmit Power is adjusted.
Ramp Offset Adjust this item to the optimal Ramp voltage.
Balance The transmit modulation frequency response is adjusted.This item is adjusted so that the deviationof 2kHz becomes the same deviation of 20Hz.This item must be adjusted before all adjustment items for deviations are adjusted.
Maximum Deviation(Analog Wide 5k/Wide 4k/Narrow)
Maximum Deviation of Analog (Wide 5k/Wide 4k/Narrow) is adjusted.This item must be adjusted before all adjustment items for tone deviations are adjusted.
High Deviation NXDN/DMR high deviation is adjusted.
QT Deviation QT deviation is adjusted.
DQT Deviation DQT deviation is adjusted.
LTR Deviation LTR deviation is adjusted.
DTMF Deviation DTMF deviation is adjusted.
Single Tone Deviation
The deviation of Single Tone used in “2-tone” and “5-tone” is adjusted.
MSK Deviation MSK deviation is adjusted.
CW ID Deviation CWID tone deviation is adjusted.CWID is used to inform the others who istransmitting on a 6.25-kHz spacing channel.(In FCC rule, Analog mode or CWID isrequired for each channel-spacing.)
IQ Phase Correction of phase difference shift between I and Q.
RSSI Reference The minimum RSSI level for scan stop isadjusted.
Squelch Open The squelch level at level “1” is adjusted.
Squelch Tight The squelch level at level “9” is adjusted.
Low RSSI RSSI display level “ ” is adjusted.Both “Low RSSI” and “High RSSI” must beadjusted. (The curve data of RSSI level isapplied.)
High RSSI
Adjustment Item Description
1-64 (No.RA054<Rev.001>)
4.12.5 Adjustment item and Display
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide 5k)
AS(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1 LCD Contrast CNTR - 1 point ADJ CommonSection 21~256
2 VCO Assist AST (CV voltage) - - 9 - - - CommonSection 31~4096
3 RTC Correction RTC - - CommonSection 5-2.00 ~ -0.01 ,0.00 ,+0.01 ~ +2.00
4 Maximum Transmit Power
MAX_P - - - 5 - - - TransmitterSection 11~256
5 High Transmit Power
H_PWR - - - 5 - - - TransmitterSection 21~1024
6 Medium Transmit Power
M_PWR - - - 5 - - - TransmitterSection 31~1024
7 Low Transmit Power
L_PWR - - - 5 - - - TransmitterSection 41~1024
8 Ramp Offset RAMP (ADC measurement value)
1 point ADJ TransmitterSection 51~1024
9 Balance BAL (Encode frequency) - - 5 - - - TransmitterSection 61~1024
10 Maximum Deviation
ADEV - 5 5 5 - - - TransmitterSection 71~1024
11 NXDN High Deviation
NDEV - - - - 5 5 - TransmitterSection 81~1024
12 DMR High Deviation
DDEV - - - - - - 5 TransmitterSection 91~1024
13 QT Deviation QT - 5 5 5 - - - TransmitterSection 101~1024
14 DQT Deviation DQT - 5 5 5 - - - TransmitterSection 111~1024
15 LTR Deviation LTR - 5 5 5 - - - TransmitterSection 121~1024
16 DTMF Deviation DTMF - 5 5 5 - - - TransmitterSection 131~1024
17 Single Tone Deviation
TONE - 5 5 5 - - - TransmitterSection 141~1024
18 MSK Deviation MSK - 5 5 5 - - - TransmitterSection 151~1024
19 CW ID Deviation CWID - - - 5 - - - TransmitterSection 161~1024
20 IQ Phase IQ (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 21~63
21 RSSI Reference 1 DSP (Receive)
RSSI1 (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
(No.RA054<Rev.001>)1-65
22 RSSI Reference 2 RF IC(Receive)
RSSI2 (RSSI RF IC(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
23 RSSI Reference 3 DSP (Standby)
RSSI3 (RSSI DSP (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
24 RSSI Reference 4 RF IC (Standby)
RSSI4 (RSSI RF IC (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
25 Squelch Open SQL (ASQDET measurement value)
5 5 5 5 5 5 ReceiveSection 41~256
26 Squelch Tight SQLT (ASQDET measurement value)
5 5 5 - - - ReceiveSection 51~256
27 Low RSSI LRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 61~256
28 High RSSI HRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 71~256
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide 5k)
AS(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1-66 (No.RA054<Rev.001>)
4.12.6 Panel tuning mode flow chartNote:
* In this Panel tuning mode flow chart, the Adjustment item name is modified.Panel Test Mode
[ ]hold
LCD Contrast
CNTR
levelecnerefer9VCO Assist
stnemtsujdAAST
RTC Correction
RTC
Ramp Offset
RAMP
High Power Narrow 5 reference level
H_PWR An Adjustments
Medium Power Narrow 5 reference level
M_PWR An Adjustments
Low Power Narrow 5 reference level
L_PWR An Adjustments
Balance Narrow 5 reference level
BAL An Adjustments
5 reference level
Adjustments
5 reference level
Adjustments
NXDN High Deviation Narrow NXDN High Deviation VeryNarrow
NDEV Nn NDEV Nv
CW ID Deviation Narrow
CWID An
RSSI (Low) Narrow
nAISSRL
RSSI (High) Narrow
nAISSRH
Adjustment Item N/W/VN
LCD Display
For all adjustment items, press the [ ] button
to write the adjustment value.
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]
5 reference level
Adjustments
[ ]
RSSI Referance 1
RSSI1[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]IQ Phase
IQ[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 2
RSSI2[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 3
RSSI3[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 4
RSSI4
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
DMR High Deviation
DDEV
[ ]press [ ]hold
Adjustment Point
LCD Display
5 reference level
L1
L3
C2
H3
H1
Low 1
Adjustments
Low 3
Center 2
High 3
5 reference level
Adjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]High 1 [ ]
[ ]
[ ]
High Transmit Power
Medium Transmit Power
Low Transmit Power
Maximum Deviation
NXDN High Deviation
DMR High DeviationQT Deviation
DQT Deviation
LTR Deviation
DTMF Deviation
Single Tone Deviation
MSK Deviation
CW ID Deviation
IQ Phase
RSSI Reference 1
RSSI Reference 2
RSSI Reference 3
RSSI Reference 4
Open Squelch
Low RSSI
High RSSI
Tight Squelch
Adjustment Point
LCD Display
9 reference level
L1
L2
L3
H3
C1
C2
C3
H1
H2
Low 1
Adjustments
Low 2
Low 3
High 3
9 reference level
Adjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Center 1 [ ]
[ ]
Center 2
Center 3
[ ]
[ ][ ]
[ ]High 1 [ ]
[ ]
High 2 [ ]
[ ]
[ ]
Balance
VCO Assist
[ ]press [ ]hold
DMR
D
5 reference level
Adjustments
[ ]
5 reference level
Adjustments
[ ]
Maximum Transmit Power
5 reference level
Adjustments
Analog Max Deviation Narrow Analog Max Deviation Wide4k Analog Max Deviation Wide5k
ADEV An ADEV As ADEV Aw
[ ]
[ ] [ ] [ ]
[ ] [ ]
[ ]press [ ]hold
Single Tone Deviation Narrow Single Tone Deviation Wide4k
TONE An TONE Aw[ ] [ ][ ]press [ ]hold
[ ]
MSK Deviation Narrow MSK Deviation Wide4k MSK Deviation Wide5k
MSK An MSK As MSK Aw5 reference levelAdjustments
[ ]
[ ]
QT Deviation Narrow QT Deviation Wide4k
sATQnATQ
DQT Deviation Narrow DQT Deviation Wide4k
DQT An DQT As
LTR Deviation Narrow LTR Deviation Wide4k
sARTLnARTL
DTMF Deviation Narrow DTMF Deviation Wide4k
DTMF An DTMF As
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]5 reference level
[ ]
QT Deviation Wide5k
QT Aw
5 reference levelAdjustments
[ ]
5 reference levelAdjustments
DQT Deviation Wide5k
DQT Aw5 reference levelAdjustments
LTR Deviation Wide5k
LTR Aw
DTMF Deviation Wide5k
DTMF Aw
Adjustments
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
[ ]
5 reference level
[ ]Single Tone Deviation Wide5k
TONE Aw
Adjustments[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]
Squelch (Open) Narrow Squelch (Open) Wide4k Squelch (Open) Wide5k Squelch (Open)
SQL An SQL As SQL Aw SQL
[ ]
[ ] [ ] [ ] [ ] [ ]
[ ] [ ] [ ] [ ]
[ ]
5 reference level
Adjustments
VeryNarrow
NvNarrow
Nn
Squelch (Open)
DMR
D
Squelch (Open)[ ]press [ ]hold
[ ]Squelch (Tight) Narrow Squelch (Tight) Wide4k Squelch (Tight) Wide5k
wATLQSsATLQSnATLQS
5 reference level
Adjustments
[ ] [ ] [ ]
[ ] [ ]
[ ]press [ ]hold
Max PowerMAX_P
[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]
(No.RA054<Rev.001>)1-67
4.13 Adjustment points
TX-RX UNIT (XC1-182)Component Side
4.14 Test Equipment Required for Alignment
*The test equipment which is not used for adjustment is contained in this table.
RTC (CN55)
RT
C
Test Equipment Major Specifications
1. Standard Signal Generator (SSG)
Frequency RangeModulation Output
100 to 900MHzFrequency modulation and external modulation-127dBm/0.1uV to greater than -20dBm/22.4mV
When performing the Frequency adjustment, the following accuracy is necessary.• 0.003ppmUse a standard oscillator for adjustments, if necessary.
2. Power Meter Input ImpedanceOperation FrequencyMeasurement Capability
50ohm100 to 900MHzVicinity of 100W
3. Deviation Meter Frequency Range 100 to 900MHz
4. Digital Volt Meter (DVM)
Measuring RangeInput Impedance
10mV to 20V DCHigh input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. Frequency Counter Frequency RangeFrequency Stability
10Hz to 1000MHz0.2ppm or less
To measure the oscillating frequency of the internal clock 32766.00Hz~32770.00Hz forRTC Correction Resolution 0.01Hz is better for accuracy adjustment.
7. Ammeter 20A or more
8. AF Volt Meter (AF VM) Frequency RangeVoltage Range
50Hz to 10kHz1mV to 10V
9. Audio Generator (AG) Frequency RangeOutput
50Hz to 5kHz or more0 to 1V
10. Distortion Meter CapabilityInput Level
3% or less at 1kHz50mV to 10Vrms
11. Spectrum Analyzer Measuring Range DC to 1GHz or more
12. 4ohm Dummy Load Approx. 4ohm, 10W
13. Regulated Power Supply 13.2V, approx. 20A (adjustable from 9V to 17V)Useful if ammeter equipped
1-68 (No.RA054<Rev.001>)
Test cable for microphone input (E30-3360-28) MIC connector (Front panel view)
Tuning cable (E30-7754-05)Adapter cable (E30-7754-05) is required for injecting an audioif PC tuning is used.See “PC Mode” section for the connection.
4.15 Radio check Section
3
2
4
5
6
7
8
3
1
2
4
5
6
7
8
1GREEN
RED
BLACK
BLUE
SHIELD
WHITE
GRAY
YELLOW
PTT
E
MIC-E
MIC
HK
1 : BLC
2 : +B
3 : GND
4 : PTT/TXD (PC serial data from radio)
5 : MICE
6 : MIC
7 : HOOK/RXD (PC serial data to radio)
8 : DM
1
8
Item Condition Measurement Adjustment Specifications/RemarksPanel test
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Frequency check
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
f. counter Panel ANT Check an internal temperature of radio from 20°C to 33°C.
±0.25ppm±[email protected]
2. High power check
1)CH-Sig: 1-1PTT: ONTA: OFF
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 21W~29W10A or less
2)CH-Sig: 2-1PTT: ONTA: OFF
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ONTA: OFF
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
(No.RA054<Rev.001>)1-69
3. Low power check
1)CH-Sig: 1-1PTT: ONTA: OFF
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 3.5W~6.5W7.0A or less
2)CH-Sig: 2-1PTT: ONTA: OFF
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ONTA: OFF
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
4. MIC sensitivity check
1)CH-Sig: 1-1AG: 1kHzPTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1AG: 1kHzPTT: Press [Transmit] button.
DeviationmeterOscilloscopeAGAF VM
Panel ANTMIC jack
Adjust AGinput to get astandardMOD.
5mV ±1mV
5. Sensitivitycheck
1)CH-Sig: 1-1SSG outputWide 5k: -117dBm(0.32μV)(MOD: 1kHz/±3kHz)Wide 4k:-117dBm (0.32μV)(MOD: 1kHz/±2.4kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG outputWide 5k: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Wide 4k: -117dBm (0.32μV)(MOD: 1kHz/±2.4kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
SSGAF VMOscilloscopeDistortionmeter4ohmDummy load
Panel ANTExt. SPconnector
Check 12dB SINAD or more
Item Condition Measurement Adjustment Specifications/RemarksPanel test
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-70 (No.RA054<Rev.001>)
4.16 Common Section
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Setting
1) DC voltage:13.2V2) SSG standard modulation
[Wide 5k] MOD:1kHz,DEV:3kHz[Wide 4k] MOD:1kHz,DEV:2.4kHz[Narrow] MOD:1kHz,DEV:1.5kHz
2.LCD Contrast
1) Adj item[CNTR]Adjust:[****]
Press [ ] button to store the adjustment value.
1) Adj item[LCD Contrast]Data: [****]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.
280 (Reference value)
3. VCO Assist
1) Adj item:[AST]Adjust:[****]
2) Adj item:[L1]→[L2]→[L3]→[C1]→[C2]→[C3]→[H1]→[H2]→[H3]→
Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [VCO Assist]
2) Adj item:[Low1],[Low2], [Low3], [Center1], [Center2], [Center3], [High1],[High2][High3]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment][V] Indicator on the PC window shows VCO lock voltage. Change the adjustment value to get VCO lock voltage within the limit of the specified voltage.
Note:Confirm the VCO lock voltage approximately 3 seconds after the adjustment value is changed.
2.5V±0.1V[Automatic Adjustment]After the automatic adjustment is performed, verify that the VCO lock voltage is within the voltage range which is specified by the manual adjustment.[Manual Adjustment]Press [Apply] button to store the adjustment value after all adjustment points have been adjusted.Adjustment value range: 300 - 3000
(No.RA054<Rev.001>)1-71
4. Frequency
*The Frequency adjustment can be performed only in PC test mode.
1) Adj item: [Frequency]SSG output: -20dBm (22.4mV) (CW (without modulation))
Caution:Perform the frequency adjustment under the following conditions.
• Temperature range of +20°C to +33°C (+68.0°F to +91.4°F).(The temperature is displayed on the Frequency adjustment screen of the KPG-D3/D3N and the LCD of the transceiver.)
• Use an accuracy of 0.003ppm for the SSG. (Use a standard oscillator if necessary.)
SSG Panel ANT [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode]Press [Start] button of “Auto Tuning”. Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
[PC test mode]“IF20” value = Within 0±10 digits. The value of “IF20” will become around “0” after the adjustment has finished.
Remark:“Frequency” is adjusted under receiving condition with SSG.
5. RTC Correciton
1) Adj item:[RTC]Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [RTC Correction]Data: [****]Press [Apply] button to store the adjustment value.
Frequency Counter
TX-RX
TESTPOINT(CN55)
Remark:The adjustment value should input the display of a Frequency Counter.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-72 (No.RA054<Rev.001>)
4.17 Transmitter Section
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Maximum Transmit Power
1) Adj item:[MAX_P]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maximum Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
57.5W ±2.5W 15A or less
2. High Transmit power
1) Adj item:[H_PWR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust: [****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [High Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
25W ±1W10A or less
3. Low Transmit power
1) Adj item:[L_PWR]
Adjust:[****]2) Adj item:
[L1]→[L3]→[C2]→[H1]→[H3]Adjust: [****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Low Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
5W ±0.5W7A or less
(No.RA054<Rev.001>)1-73
4.Ramp Offset
1)Adj item:[RAMP]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Ramp Offset]Press [Autotune(TX starts)] button. Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune(TX
starts)] button.2) Press [Apply] button
to store the adjustment value after the automatic adjustment has finished.
3) Check Ramp Offset Monitor Value Over 60.
[Manual Adjustment]1) Set the adjustment
value to "1".2) Press [Transmit]
button and increase the adjustment value slowly while monitoring the offset monitor value.
3) Set the adjustment value when the offset monitor value exceed "75".
5. Balance
1) Adj item: [An BAL]Adjust:[****]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Balance]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
The Deviation of 20Hz frequency is fixed.Change the 2kHz adjustment value to become the same deviation of 20Hz within the specified range.[Panel tuning mode]PTT:ONWhile PTT:ON, press the [] button to change the 20Hz/2kHz.[PC test mode]PTT: Press [Transmit] button.While PTT:ON, click the check box "2kHz Sine Wave" to change the 20Hz/2kHz.
2kHz Tone deviation is within ± 1.0% of 20Hz tone deviation.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-74 (No.RA054<Rev.001>)
6. Maximum Deviation
[Analog Wide 5k]
1) Adj item: [Aw ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the deviation is between 4150Hz and 4250Hz.Deviation meterLPF: 15kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
4150~4250Hz
[Analog Wide 4k]
1) Adj item: [As ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the deviation is between 3310Hz and 3410Hz.Deviation meterLPF: 15kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
3310~3410Hz
[Analog Narrow]
1) Adj item: [An ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the deviation is between 2050Hz and 2150Hz.Deviation meterLPF: 15kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2050~2150Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-75
7. NXDN High Deviation[NXDN Narrow]
1) Adj item: [Nn NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the Analog deviation is between 2995Hz and 3117Hz.Deviation meterLPF: 3kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2995~3117Hz
[NXDN Very Narrow]
1) Adj item: [Nv NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Very Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the Analog deviation is between 1311Hz and 1363Hz.Deviation meterLPF: 3kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
1311~1363Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-76 (No.RA054<Rev.001>)
8. DMR High Deviation
1) Adj item: [D DDEV]Adjust: [****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DMR High Deviation (DMR Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the Analog deviation is between 2695Hz and 2803Hz.Deviation meterLPF: 3kHzHPF: OFF
500(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2695~2803Hz
9. QT Deviation
[Analog Wide 5k]
1) Adj item: [Aw QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
0.75kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
0.60kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-77
[Analog Narrow]
1) Adj item: [An QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
0.35kHz±0.05kHz
10. DQT Deviation
[Analog Wide 5k]
1) Adj item: [Aw DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.430 (Reference value)
0.75kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.430 (Reference value)
0.60kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-78 (No.RA054<Rev.001>)
[Analog Narrow]
1) Adj item: [An DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.430 (Reference value)
0.35kHz±0.05kHz
11. LTR Deviation
[Analog Wide 5k]
1) Adj item: [Aw LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
1.00kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
0.90kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-79
[Analog Narrow]
1) Adj item: [An LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
0.75kHz±0.05kHz
12. DTMF Deviation
[Analog Wide 5k]
1) Adj item: [Aw DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.555 (Reference value)
2.50kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.555 (Reference value)
2.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-80 (No.RA054<Rev.001>)
[Analog Narrow]
1) Adj item: [An DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.555 (Reference value)
1.25kHz±0.05kHz
13. Single Tone Deviation
[Analog Wide 5k]
1) Adj item: [Aw TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
3.00kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
2.40kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-81
[Analog Narrow]
1) Adj item: [An TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
1.50kHz±0.05kHz
14. MSK Deviation
[Analog Wide 5k]
1) Adj item: [Aw MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
3.00kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
2.40kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-82 (No.RA054<Rev.001>)
[Analog Narrow]
1) Adj item: [An MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
1.50kHz±0.05kHz
15. CWID Deviation
[Analog Narrow]
1) Adj item: [An CWID]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [CWID Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.512 (Reference value)
1.10kHz±0.10kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-83
4.17.1 Necessary Deviation adjustment item for each signaling and modeThe following shows the necessary adjustment items for each signaling deviation. Please read the following table like the followingexample. In the case of the signaling "QT (Analog Wide 5k)", this signaling is composed of three elements [Balance, MaximumDeviation (Analog Wide 5k) and QT Deviation (Analog Wide 5k)]. Please adjust Balance and Maximum Deviation (Analog Wide 5k)before adjusting QT Deviation (Analog Wide 5k).
• Balance is common with all the above deviation adjustments. If Balance (Transmitter Section 6) has already adjusted, please skipStep1 and adjust from Step2.
• Maximum Deviation (Analog Wide 5k/Wide 4k/Narrow) is common with all the analog signaling deviations and CWID Deviation(NXDN Very Narrow).If Balance and Maximum Deviation (Analog Wide 5k /Wide 4k/Narrow) (Transmitter Section 7) have already adjusted, please skipStep2 and adjust from Step3.
Mode Signaling Necessary adjustment and order
Wide 5k Wide 4k Narrow Very Narrow
Analog Audio 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]
-
QT 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. QT Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. QT Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. QT Deviation
[Analog Narrow]
-
DQT 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. DQT Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. DQT Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DQT Deviation
[Analog Narrow]
-
LTR 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. LTR Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. LTR Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. LTR Deviation
[Analog Narrow]
-
DTMF 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. DTMF Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. DTMF Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DTMF Deviation
[Analog Narrow]
-
5TONE 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. Single Tone Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. Single Tone Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. Single Tone Deviation
[Analog Narrow]
-
MSK(Fleetsync)
1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. MSK Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. MSK Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. MSK Deviation
[Analog Narrow]
-
NXDN Audio - - 1. Balance adjust2. NXDN High Deviation
[NXDN Narrow]
1. Balance adjust2. NXDN High
Deviation [NXDN Very Narrow]
CWID - - - 1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. CWID Deviation
[Analog Narrow]
DMR Audio - - 1. Balance adjust2. DMR High Deviation
-
1-84 (No.RA054<Rev.001>)
4.18 Receiver Section
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. AF level setting
[Panel test mode]1) CH-Sig: 1-1
SSG output: -47dBm (1mV)(MOD: 1kHz/±1.5kHz)
1) Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG output: -47dBm (1mV) (MOD:1kHz/±1.5kHz)
SSGDVMAF VMDummy load
Panel ANTExt. SP connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Volume Up/Down knob to obtain 1.41V AF output.(0.5W @ 4ohm load)
1.41V±0.1V
2. IQ Phase
1) Adj item: [An IQ]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
1) Adj item: [IQ Phase]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]After input signal from SSG,1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment]Adjust RSSI Level(DSP Normal Power Mode)Value to the minimum.
3. RSSI reference [DSP (Receive)]
1) Adj item: [An RSSI 1]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 1 DSP (Receive)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Receive)]
1) Adj item: [An RSSI 2]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 2 RF IC (Receive)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
(No.RA054<Rev.001>)1-85
[DSP (Standby)]
1) Adj item: [An RSSI 3]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 3 DSP (Standby)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Standby)]
1) Adj item: [An RSSI 4]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 4 RF IC (Standby)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
4. Squelch Open
[Analog Wide 5k]
1) Adj item: [Aw SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Open (Analog Wide 5k)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-86 (No.RA054<Rev.001>)
[Analog Wide 4k]
1) Adj item: [As SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±2.4kHz)
1) Adj item: [Squelch Open (Analog Wide 4k)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±2.4kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Open (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[NXDN Narrow]
1) Adj item: [Nn SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-87
[NXDN Very Narrow]
1) Adj item: [Nv SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Very Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[DMR] 1) Adj item: [D SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
1) Adj item: [Squelch Open (DMR)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
5. Squelch Tight
[Analog Wide 5k]
1) Adj item: [Aw SQLT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Tight (Analog Wide 5k)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-88 (No.RA054<Rev.001>)
[Analog Wide 4k]
1) Adj item: [As SQLT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±2.4kHz)
1) Adj item: [Squelch Tight (Analog Wide 4k)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±2.4kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQLT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Tight (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
6. Low RSSI
1) Adj item: [An LRSSI]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [Low RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
7. High RSSI
1) Adj item: [An HRSSI]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [High RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-89
4.19 NX-3820H(G)/3820H K,K2 TYPE Controls
4.19.1 Preparations for checking/tuning the transceiverBefore attempting to check/tune the transceiver, connect the unitto a suitable power supply.Whenever the transmitter is turned on, the unit must beconnected to a suitable dummy load (i.e. power meter).The speaker output connector must be terminated with an 4ohmdummy load and connected to an AC voltmeter and an audiodistortion meter or a SINAD measurement meter at all timesduring checking/tuning.
4.20 Panel Test Mode
4.20.1 Test mode operation featuresThis transceiver has a test mode. To enter test mode, press andhold the [ ] button while turning the transceiver power ON orpress the [ ] button and select the "Panel Test". Before thetransceiver enters test mode, the frequency version informationappears on the LCD momentarily. Test mode can be inhibited byprogramming. To exit test mode, turn the transceiver power OFF.The following functions are available in test mode.
• When the panel test mode is activated, the last used channeland signaling numbers are displayed. When the panel testmode is activated for the first time, the channel and signalingnumbers are 1.
4.20.2 Button operation
*1: When the mode is selected as Analog, this function isenabled.
Power switch
Channel Up/Down buttonVolume Up/Down button
MIC jack
KMC-36 (OPTION)
Keypad
[PTT]
Button "Func" not appears on the sub LCD display
Function Display
[+] Push: Volume upHold: Volume up continuously
-
[-] Push: Volume downHold: Volume down continuously
-
[] Push: Test channel upHold: Test channel up continuously
Channel No.
[] Push: Test channel downHold: Test channel down continuously
Channel No.
[] Push: Squelch level up *1Hold: Squelch off
Squelch levelSquelch off: icon appears
[] Wide/Narrow/Very Narrow
Wide : "w"Narrow: "n"Very Narrow: "v"
[ ] Shift to panel tuning mode
-
[ ] Function on "Func" appears on the sub LCD display
[ ] Push: Test signaling upHold: Test signaling up continuously
Signaling No.
[ (AUX)] MSK 1200bps and 2400bps *1
2400bps: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
- -
Button "Func" appears on the sub LCD display
Function Display
[+] Function off -
[-] Function off -
[] - -
[] Mode selectionAnalog/NXDN/DMR
Analog: "A"NXDN: "N"DMR: "D"
[] Function off -
[] Button/LCD check The contents of the pressed button etc., appear.
[ ] High power/Medium power/Low power
High:[ ] icon appearsMedium:[ ] icon appearsLow:[ ] icon appears
[ ] Function off -
[ ] External Speaker on/off On: icon appears
[ (AUX)] Compander on/off On: [ ] icon appears
[PTT] Transmit -
1-90 (No.RA054<Rev.001>)
• LED indicatorRed LED Lights during transmission.Green LED Lights when there is carrier.
• Sub LCD indicator"Func" Appears at function on.
• LCD display in panel test mode
4.20.3 Frequency and SignalingThe transceiver has been adjusted for the frequencies shown inthe following table. When required, readjust them following theadjustment procedure to obtain the frequencies you want inactual operation.
(1) Test frequency
(2) SignalingAnalog Type Signaling
[0] to [9]and[#], [ ]
Function off -
Button "Func" appears on the sub LCD display
Function Display
(Power ON)
Type Frequency range
"F1": 450~520MHz
"F2": 400~470MHz
(After 2sec.)
Temperature [oC]Power
An : Analog narrow mode
Aw : Analog wide 5k mode
Nn : NXDN narrow mode
Nv : NXDN very narrow mode
D : DMR mode
Squelch level
(Analog mode only)
Sub LCD display
Main LCD display Signaling
No.
Channel No.
Kx types are
displayed as "K".
CH K K2
RX (MHz) TX (MHz) RX (MHz) TX (MHz)
1 485.05000 485.10000 435.05000 435.10000
2 450.05000 450.10000 400.05000 400.10000
3 519.95000 519.90000 469.95000 469.90000
4 485.00000 485.00000 435.00000 435.00000
5 485.20000 485.20000 435.20000 435.20000
6 485.40000 485.40000 435.40000 435.40000
7~16 - -
No. RX TX
1 None None
2 None Square Wave
3 LTR Data LTR Data
4 QT:67.0Hz QT:67.0Hz
5 QT:151.4Hz QT:151.4Hz
6 QT:210.7Hz QT:210.7Hz
7 QT:254.1Hz QT:254.1Hz
8 DQT:D023N DQT:D023N
9 DQT:D754I DQT:D754I
10 DTMF Decode (CODE: 159D)
DTMF Encode (CODE: 159D)
11 None DTMF Encode (CODE: 9)
12 2-tone Decode (A: 304.7Hz, B: 3106.0Hz)
2-tone Encode (A: 304.7Hz,B: 3106.0Hz)
13 Single Tone Decode (979.9Hz)
Single Tone Encode (979.9Hz)
14 None Single Tone Encode (1000Hz)
15 None MSK PN9
16 MSK Decode MSK Encode
(No.RA054<Rev.001>)1-91
NXDN Type Signaling
RAN: Radio Access NumberPN9: Pseudo-Random PatternNo.7, 9 Item: PC test mode only
DMR Type Signaling
4.21 Panel Tuning Mode
4.21.1 Transceiver tuning (To enter tuning mode)To enter tuning mode, press the [ ] button while the transceiveris in test mode. Use the [ (AUX)] button to write tuning datathrough tuning modes, and the [ ]/[ ] button to adjust tuningrequirements (1 to 4096 appears on the LCD).Use the [ ] button to select the adjustment item through tuningmodes. Use the [ ] button to adjust 5, 9 or 17 reference leveladjustments, and use the [ ] button to switch between Wide/Narrow.• LCD display in panel tuning mode
4.21.2 Button operation
No. RX TX
1 RAN1 RAN1
2 None PN9
3 RAN1 Maximum Deviation Pattern
7 FSW + PN9 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
No. RX TX
1 CC 00 Burst CC 00 Burst
2 PN9 PN9
3 CC 00 Burst Maximum Deviation Pattern
4 CC 00 Burst 1/3 Deviation Pattern
5 CC 00 Burst 0 Continuous Pattern
6 SYNC (Each Slot) +PN9 Burst Pattern
SYNC (Each Slot) + PN9Burst Pattern
7 SYNC (Super Frame) +PN9 Burst Pattern
SYNC (Super Frame) +PN9 Burst Pattern
8 CC 00 Burst 0 Burst Pattern
9 Tone Pattern Tone Test Burst Pattern
10 Silence Pattern Silence Burst Pattern
11 Audio Test Pattern Audio Test Burst Pattern
12 Vocoder Loop None
An AST 2562.6
CV voltage, AD value, etc
Sub LCDdisplay
L1
Adjustment point
Main LCDdisplay Adjustment value
(1~4096)
Proper value guide(When the frequency adjustment is necessary,
or is displayed.)
Adjustment item
An : Analog narrow modeAw : Analog wide 5k modeAs : Analog wide 4k mode *1Nn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
*1: Wide 4k is displayed only when the PC test mode is used. However, it aims at production for factory, or a operation verification of the transceiver. It is not necessary in operation of the transceiver to adjust.
L1L2L3L4L5L6C1C2C3
C4C5H1H2H3H4H5H6
Button Function
Push Hold (1 second)
[+] Volume up Continuation up
[-] Volume down Continuation down
[ ] Adjustment value up Continuation up
[ ] Adjustment value down Continuation down
[ ] Auto adjustment start Output tone pattern change of balance adjustment (A change is possible only during balance adjustment.)
[ ] Wide/Narrow/NXDN/DMR
-
[ ] Shift to panel test mode -
[ ] To enter 5,9 or 17 reference level adjustments
-
[ ] Go to next adjustment item
Back to last adjustment item (At the time of 5, 9 or 17 point adjustment: Adjustment point change)
[ (AUX)] Writes the adjustmentvalue
-
[PTT](MIC)
Transmit
[0] to [9]and[#],[ ](MIC)
-
1-92 (No.RA054<Rev.001>)
4.21.3 5, 9 or 17 reference level adjustments frequencyMaximum Transmit Power, High Transmit Power, Medium Transmit Power, Low Transmit Power, IQ Phase, RSSI Reference,Squelch Open, Squelch Tight, Low RSSI, High RSSI
Balance, Maximum Deviation , NXDN High Deviation, DMR High Deviation, QT Deviation, DQT Deviation, LTR Deviation,DTMF Deviation, Single Tone Deviation, MSK Deviation, CW ID Deviation
VCO Assist
Tuning point Display K K2
RX (MHz) TX (MHz) RX (MHz) TX (MHz)
1 L1 450.050000 450.100000 400.05000 400.10000
2 L5 467.550000 467.600000 417.55000 417.60000
3 C3 485.050000 485.100000 435.05000 435.10000
4 H2 502.550000 502.600000 452.55000 452.60000
5 H6 519.950000 519.900000 469.95000 469.90000
Tuning point Display K K2
RX (MHz) TX (MHz) RX (MHz) TX (MHz)
1 L1 450.050000 450.100000 400.05000 400.10000
2 L3 458.850000 458.900000 408.85000 408.90000
3 L5 467.550000 467.600000 417.55000 417.60000
4 C1 476.350000 476.400000 426.35000 426.40000
5 C3 485.050000 485.100000 435.05000 435.10000
6 C5 493.850000 493.900000 443.85000 443.90000
7 H2 502.550000 502.600000 452.55000 452.60000
8 H4 511.350000 511.400000 461.35000 461.40000
9 H6 519.950000 519.900000 469.95000 469.90000
Tuning point Display K K2
RX (MHz) TX (MHz) RX (MHz) TX (MHz)
1 L1 450.050000 450.100000 400.05000 400.10000
2 L2 454.450000 454.500000 404.45000 404.50000
3 L3 458.850000 458.900000 408.85000 408.90000
4 L4 463.250000 463.300000 413.25000 413.30000
5 L5 467.550000 467.600000 417.55000 417.60000
6 L6 471.950000 472.000000 421.95000 422.10000
7 C1 476.350000 476.400000 426.35000 426.40000
8 C2 480.750000 480.800000 430.75000 430.80000
9 C3 485.050000 485.100000 435.05000 435.10000
10 C4 489.450000 489.500000 439.45000 439.50000
11 C5 493.850000 493.900000 443.85000 443.90000
12 H1 498.250000 498.300000 448.25000 448.30000
13 H2 502.550000 502.600000 452.55000 452.60000
14 H3 506.950000 507.000000 456.95000 457.10000
15 H4 511.350000 511.400000 461.35000 461.40000
16 H5 515.750000 515.800000 465.75000 465.80000
17 H6 519.950000 519.900000 469.95000 469.90000
(No.RA054<Rev.001>)1-93
4.21.4 Adjustment item supplement
Adjustment Item Description
LCD Contrast The contrast of LCD display can be changed.
VCO Assist The lock voltage of VCO is adjusted.This item must be adjusted before receiver and transmitter adjustment items.
Frequency Frequency is adjusted under receivingcondition with SSG.The SSG needs 0.001ppm accuracy soplease use a standard oscillator if necessary.This item can be adjusted only in PC TestMode so that the adjustment value is notchanged easily.
RTC Correction Real Time Clock is adjusted.This item uses the internal clock.(Any measurement equipment is not required.)
Maximum Transmit Power
Maximum Transmit Power is adjusted.
High Transmit Power
High Transmit Power is adjusted.
Mid Transmit Power
Medium Transmit Power is adjusted.
Low Transmit Power
Low Transmit Power is adjusted.
Ramp Offset Adjust this item to the optimal Ramp voltage.
Balance The transmit modulation frequency response is adjusted.This item is adjusted so that the deviationof 2kHz becomes the same deviation of 20Hz.This item must be adjusted before all adjustment items for deviations are adjusted.
Maximum Deviation(Analog Wide 5k/Wide 4k/Narrow)
Maximum Deviation of Analog (Wide 5k/Wide 4k/Narrow) is adjusted.This item must be adjusted before all adjustment items for tone deviations are adjusted.
High Deviation NXDN/DMR high deviation is adjusted.
QT Deviation QT deviation is adjusted.
DQT Deviation DQT deviation is adjusted.
LTR Deviation LTR deviation is adjusted.
DTMF Deviation DTMF deviation is adjusted.
Single Tone Deviation
The deviation of Single Tone used in “2-tone” and “5-tone” is adjusted.
MSK Deviation MSK deviation is adjusted.
CW ID Deviation CWID tone deviation is adjusted.CWID is used to inform the others who istransmitting on a 6.25-kHz spacing channel.(In FCC rule, Analog mode or CWID isrequired for each channel-spacing.)
IQ Phase Correction of phase difference shift between I and Q.
RSSI Reference The minimum RSSI level for scan stop isadjusted.
Squelch Open The squelch level at level “1” is adjusted.
Squelch Tight The squelch level at level “9” is adjusted.
Low RSSI RSSI display level “ ” is adjusted.Both “Low RSSI” and “High RSSI” must beadjusted. (The curve data of RSSI level isapplied.)
High RSSI
Adjustment Item Description
1-94 (No.RA054<Rev.001>)
4.21.5 Adjustment item and Display
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide)
AS *2(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1 LCD Contrast CNTR - 1 point ADJ CommonSection 21~256
2 VCO Assist AST (CV voltage) - - 17 - - - CommonSection 31~4096
3 RTC Correction RTC - - CommonSection 5-2.00 ~ -0.01 ,0.00 ,+0.01 ~ +2.00
4 Maximum Transmit Power
MAX_P - - - 5 - - - TransmitterSection 11~256
5 High Transmit Power
H_PWR - - - 5 - - - TransmitterSection 21~1024
6 Medium Transmit Power
M_PWR - - - 5 - - - TransmitterSection 31~1024
7 Low Transmit Power
L_PWR - - - 5 - - - TransmitterSection 41~1024
8 Ramp Offset RAMP (ADC measurement value)
1 point ADJ TransmitterSection 51~1024
9 Balance BAL (Encode frequency) - - 9 - - - TransmitterSection 61~1024
10 Maximum Deviation
ADEV - 9 9 *2 9 - - - TransmitterSection 71~1024
11 NXDN High Deviation
NDEV - - - - 9 9 - TransmitterSection 81~1024
12 DMR High Deviation
DDEV - - - - - - 9 TransmitterSection 91~1024
13 QT Deviation QT - 9 9 *2 9 - - - TransmitterSection 101~1024
14 DQT Deviation DQT - 9 9 *2 9 - - - TransmitterSection 111~1024
15 LTR Deviation LTR - 9 9 *2 9 - - - TransmitterSection 121~1024
16 DTMF Deviation DTMF - 9 9 *2 9 - - - TransmitterSection 131~1024
17 Single Tone Deviation
TONE - 9 9 *2 9 - - - TransmitterSection 141~1024
18 MSK Deviation MSK - 9 9 *2 9 - - - TransmitterSection 151~1024
19 CW ID Deviation CWID - - - 9 - - - TransmitterSection 161~1024
20 IQ Phase IQ (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 21~63
21 RSSI Reference 1 DSP (Receive)
RSSI1 (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
(No.RA054<Rev.001>)1-95
*2: Wide 4k can be set up only when the PC test mode is used.
22 RSSI Reference 2 RF IC(Receive)
RSSI2 (RSSI RF IC(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
23 RSSI Reference 3 DSP (Standby)
RSSI3 (RSSI DSP (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
24 RSSI Reference 4 RF IC (Standby)
RSSI4 (RSSI RF IC (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
25 Squelch Open SQL (ASQDET measurement value)
5 5 *2 5 5 5 5 ReceiveSection 41~256
26 Squelch Tight SQLT (ASQDET measurement value)
5 5 *2 5 - - - ReceiveSection 51~256
27 Low RSSI LRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 61~256
28 High RSSI HRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 71~256
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide)
AS *2(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1-96 (No.RA054<Rev.001>)
4.21.6 Panel tuning mode flow chartNote:
* In this Panel tuning mode flow chart, the Adjustment item name is modified.
SQL An SQL Aw SQL Nn
Squelch (Open) Narrow Squelch (Open) Wide Squelch (Open) Narrow
Panel Test Mode
[ ]hold
LCD Contrast
CNTR
VCO Assist
AST
RTC Correction
RTC
Ramp Offset
RAMP
High Power Narrow 5 reference level
H_PWR An Adjustments
Medium Power Narrow 5 reference level
M_PWR An Adjustments
Low Power Narrow 5 reference level
L_PWR An Adjustments
Balance Narrow
BAL An
Analog Max Deviation Narrow Analog Max Deviation Wide
ADEV An ADEV Aw
9 reference level
Adjustments
9 reference level
Adjustments
9 reference level
Adjustments
NXDN High Deviation Narrow NXDN High Deviation VeryNarrow
NDEV Nn NDEV Nv
QT Deviation Narrow QT Deviation Wide
wATQnATQ
9 reference level
Adjustments
DQT Deviation Narrow DQT Deviation Wide
DQT An DQT Aw
9 reference level
Adjustments
LTR Deviation Narrow LTR Deviation Wide
wARTLnARTL
9 reference level
Adjustments
DTMF Deviation Narrow DTMF Deviation Wide
DTMF An DTMF Aw
9 reference level
Adjustments
MSK Deviation Narrow MSK Deviation Wide
MSK An MSK Aw
9 reference level
Adjustments
CW ID Deviation Narrow
CWID An
Squelch (Open) DMR
5 reference level
Adjustments
RSSI (Low) Narrow
nAISSRL
RSSI (High) Narrow
nAISSRH
Adjustment Item N/W/VN
LCD Display
For all adjustment items, press the [ ] button
to write the adjustment value.
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ] [ ] [ ] [ ] [ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]
9 reference level
Adjustments
[ ]
RSSI Referance 1
RSSI1[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]IQ Phase
IQ[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 2
RSSI2[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 3
RSSI3[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 4
RSSI4[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
Single Tone Deviation Narrow Single Tone Deviation Wide
TONE An TONE Aw
9 reference level
Adjustments
[ ] [ ][ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
DMR High Deviation
DDEV
[ ]press [ ]hold
[ ]
[ ] [ ] [ ]VeryNarrow
Squelch (Tight) Narrow Squelch (Tight) Wide
wATLQSnATLQS
5 reference level
Adjustments
[ ] [ ][ ]press [ ]hold
[ ] [ ]
TLSn
[ ] [ ][ ]press [ ]hold
[ ] [ ]
[ ]press [ ]hold
DMR
D
Squelch (Open)
Nv D
[ ]
17 reference level
Adjustments
9 reference level
Adjustments
IQ Phase
RSSI Reference 1
RSSI Reference 2
RSSI Reference 3
RSSI Reference 4
Open Squelch
Low RSSI
High RSSI
Tight Squelch
VCO Assist
Maximum Deviation
NXDN High Deviation
DMR High DeviationQT Deviation
DQT Deviation
LTR Deviation
DTMF Deviation
Single Tone Deviation
MSK Deviation
CW ID Deviation
Balance
5 reference level
Adjustments
[ ]
5 reference level
Adjustments
[ ]
Max PowerMAX_P
[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]
Maximum Transmit Power
Adjustment Point
LCD Display
5 reference level
L1
L5
C3
H6
H2
Low 1
Adjustments
Low 5
Center 3
High 6
5 reference level
Adjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]High 2 [ ]
[ ]
[ ]
High Transmit Power
Medium Transmit Power
Low Transmit Power
Adjustment Point
LCD Display
9 reference level
L1
L3
L5
H6
C1
C3
C5
H2
H4
Low 1
Adjustments
Low 3
Low 5
High 6
9 reference level
Adjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Center 1 [ ]
[ ]
Center 3
Center 5
[ ]
[ ][ ]
[ ]High 2 [ ]
[ ]
High 4 [ ]
[ ]
[ ]
Adjustment Point
LCD Display
17 reference level
L1
L2
L3
L4
L5
L6
C1
C2
C3
C4
C5
H1
H2
H3
H4
H5
H6
Low 1
Adjustments
Low 2
Low 3
17 reference level
Adjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Low 4 [ ]
[ ]
Low 5
Low 6
[ ]
[ ][ ]
[ ]Center 1 [ ]
[ ]
Center 2 [ ]
[ ]
Center 3 [ ]
[ ]
Center 4 [ ]
[ ]
Center 5 [ ]
[ ]
High 1 [ ]
[ ]
High 2 [ ]
[ ]
High 3 [ ]
[ ]
High 4 [ ]
[ ]
High 5 [ ]
[ ]
High 6 [ ]
[ ]
(No.RA054<Rev.001>)1-97
4.22 Adjustment points
TX-RX UNIT (XC1-183)Component Side
4.23 Test Equipment Required for Alignment
*The test equipment which is not used for adjustment is contained in this table.
RTC (CN55)
RT
C
Test Equipment Major Specifications
1. Standard Signal Generator (SSG)
Frequency RangeModulation Output
100 to 900MHzFrequency modulation and external modulation-127dBm/0.1uV to greater than -20dBm/22.4mV
When performing the Frequency adjustment, the following accuracy is necessary.• 0.001ppmUse a standard oscillator for adjustments, if necessary.
2. Power Meter Input ImpedanceOperation FrequencyMeasurement Capability
50ohm100 to 900MHzVicinity of 100W
3. Deviation Meter Frequency Range 100 to 900MHz
4. Digital Volt Meter (DVM)
Measuring RangeInput Impedance
10mV to 20V DCHigh input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. Frequency Counter Frequency RangeFrequency Stability
10Hz to 1000MHz0.2ppm or less
To measure the oscillating frequency of the internal clock 32766.00Hz~32770.00Hz forRTC Correction Resolution 0.01Hz is better for accuracy adjustment.
7. Ammeter 20A or more
8. AF Volt Meter (AF VM) Frequency RangeVoltage Range
50Hz to 10kHz1mV to 10V
9. Audio Generator (AG) Frequency RangeOutput
50Hz to 5kHz or more0 to 1V
10. Distortion Meter CapabilityInput Level
3% or less at 1kHz50mV to 10Vrms
11. Spectrum Analyzer Measuring Range DC to 1GHz or more
12. 4ohm Dummy Load Approx. 4ohm, 10W
13. Regulated Power Supply 13.6V, approx. 20A (adjustable from 9V to 17V)Useful if ammeter equipped
1-98 (No.RA054<Rev.001>)
Test cable for microphone input (E30-3360-28) MIC connector (Front panel view)
Tuning cable (E30-7754-05)Adapter cable (E30-7754-05) is required for injecting an audioif PC tuning is used.See “PC Mode” section for the connection.
4.24 Radio check Section
3
2
4
5
6
7
8
3
1
2
4
5
6
7
8
1GREEN
RED
BLACK
BLUE
SHIELD
WHITE
GRAY
YELLOW
PTT
E
MIC-E
MIC
HK
1 : MBL
2 : +B
3 : GND
4 : PTT/TXD (PC serial data from radio)
5 : MICE
6 : MIC
7 : HOOK/RXD (PC serial data to radio)
8 : DM
1
8
Item Condition Measurement Adjustment Specifications/RemarksPanel test
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Frequency check
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
f. counter Panel ANT Check an internal temperature of radio from 20°C to 33°C.
±0.25ppm±[email protected](K2)±[email protected](K)
2. High power check
1)CH-Sig: 1-1PTT: ONTA: OFF
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 40W~50W13A or less
2)CH-Sig: 2-1PTT: ONTA: OFF
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ONTA: OFF
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
(No.RA054<Rev.001>)1-99
3.Mediumpowercheck
1)CH-Sig: 1-1PTT: ONTA: OFF
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 25W~35W10A or less
2)CH-Sig: 2-1PTT: ONTA: OFF
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ONTA: OFF
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
4. Low power check
1)CH-Sig: 1-1PTT: ONTA: OFF
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 3.5W~6.5W7.0A or less
2)CH-Sig: 2-1PTT: ONTA: OFF
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ONTA: OFF
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
5. MIC sensitivity check
1)CH-Sig: 1-1AG: 1kHzPTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1AG: 1kHzPTT: Press [Transmit] button.
DeviationmeterOscilloscopeAGAF VM
Panel ANTMIC jack
Adjust AGinput to get astandardMOD.
5mV ±1mV
Item Condition Measurement Adjustment Specifications/RemarksPanel test
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-100 (No.RA054<Rev.001>)
4.25 Common Section
6. Sensitivitycheck
1)CH-Sig: 1-1SSG outputWide: -117dBm(0.32μV)(MOD: 1kHz/±3kHz)Narrow: -117dBm(0.32μV)(MOD: 1kHz/±1.5kHz)
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG outputWide: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
SSGAF VMOscilloscopeDistortionmeter4ohmDummy load
Panel ANTExt. SPconnector
Check 12dB SINAD or more
Item Condition Measurement Adjustment Specifications/RemarksPanel test
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Setting
1) DC voltage:13.6V2) SSG standard modulation
[Wide] MOD:1kHz,DEV:3kHz[Narrow] MOD:1kHz,DEV:1.5kHz
2.LCD Contrast
1) Adj item[CNTR]Adjust:[****]
Press [ ] button to store the adjustment value.
1) Adj item[LCD Contrast]Data: [****]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.
280 (Reference value)
3. VCO Assist
1) Adj item:[AST]Adjust:[****]
2) Adj item:[L1]→[L2]→[L3]→[L4]→[L5]→[L6]→[C1]→[C2]→[C3]→[C4]→[C5]→[H1]→[H2]→[H3]→[H4]→[H5]→[H6]Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [VCO Assist]
2) Adj item:[Low1],[Low2], [Low3],[Low4],[Low5], [Low6][Center1], [Center2], [Center3], [Center4], [Center5], [High1],[High2][High3],[High4],[High5][High6]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment][V] Indicator on the PC window shows VCO lock voltage. Change the adjustment value to get VCO lock voltage within the limit of the specified voltage.
Note:Confirm the VCO lock voltage approximately 3 seconds after the adjustment value is changed.
2.5V±0.1V[Automatic Adjustment]After the automatic adjustment is performed, verify that the VCO lock voltage is within the voltage range which is specified by the manual adjustment.[Manual Adjustment]Press [Apply] button to store the adjustment value after all adjustment points have been adjusted.Adjustment value range:K: 1200 - 4096K2: 500 - 1950
(No.RA054<Rev.001>)1-101
4.26 Transmitter Section
4. Frequency
*The Frequency adjustment can be performed only in PC test mode.
1) Adj item: [Frequency]SSG output: -20dBm (22.4mV) (CW (without modulation))
Caution:Perform the frequency adjustment under the following conditions.
• Temperature range of +20°C to +33°C (+68.0°F to +91.4°F).(The temperature is displayed on the Frequency adjustment screen of the KPG-D3/D3N and the LCD of the transceiver.)
• Use an accuracy of 0.001ppm for the SSG. (Use a standard oscillator if necessary.)
SSG Panel ANT [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode]Press [Start] button of “Auto Tuning”. Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
[PC test mode]“IF20” value = Within 0±30 digits. The value of “IF20” will become around “0” after the adjustment has finished.
Remark:“Frequency” is adjusted under receiving condition with SSG.
5. RTC Correciton
1) Adj item:[RTC]Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [RTC Correction]Data: [****]Press [Apply] button to store the adjustment value.
Frequency Counter
TX-RX
TESTPOINT(CN55)
Remark:The adjustment value should input the display of a Frequency Counter.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1.MaximumTransmitPower
1) Adj item:[MAX_P]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maximum Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
57.5W ±2.5W15A or less
1-102 (No.RA054<Rev.001>)
2. High Transmit power
1) Adj item:[H_PWR]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [High Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
45W ±1W 13A or less
3. Medium Transmit power
1) Adj item:[M_PWR]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Medium Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
30W ±1W 10A or less
4. Low Transmit power
1) Adj item:[L_PWR]
Adjust:[****]2) Adj item:
[L1]→[L5]→[C3]→[H2]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Low Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
5W ±0.5W 7A or less
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-103
5.Ramp Offset
1)Adj item:[RAMP]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Ramp Offset]Press [Autotune(TX starts)] button. Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune(TX
starts)] button.2) Press [Apply] button
to store the adjustment value after the automatic adjustment has finished.
3) Check Ramp Offset Monitor Value Over 50.
[Manual Adjustment]1) Set the adjustment
value to "1".2) Press [Transmit]
button and increase the adjustment value slowly while monitoring the offset monitor value.
3) Set the adjustment value when the offset monitor value exceed "60".
6. Balance
1) Adj item: [An BAL]Adjust:[****]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Balance]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
The Deviation of 20Hz frequency is fixed.Change the 2kHz adjustment value to become the same deviation of 20Hz within the specified range.[Panel tuning mode]PTT:ONWhile PTT:ON, press the [] button to change the 20Hz/2kHz.[PC test mode]PTT: Press [Transmit] button.While PTT:ON, click the check box "2kHz Sine Wave" to change the 20Hz/2kHz.
2kHz Tone deviation is within ± 1.0% of 20Hz tone deviation.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-104 (No.RA054<Rev.001>)
7. Maximum Deviation
[Analog Wide]
1) Adj item: [Aw ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2V]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point.(The value is written below.)Transmit at each adjustment point and check that the deviation is between 4150Hz and 4250Hz.Deviation meterLPF: 15kHzHPF: OFF
K:500(Reference value)K2:496(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
4150~4250Hz
[Analog Narrow]
1) Adj item: [An ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point.(The value is written below.)Transmit at each adjustment point and check that the deviation is between 2050Hz and 2150Hz. Deviation meterLPF: 15kHzHPF: OFF
K:500(Reference value)K2:493(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2050~2150Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-105
8. NXDN High Deviation[NXDN Narrow]
1) Adj item: [Nn NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point.(The value is written below.)Transmit at each adjustment point and check that the Analog deviation is between 2995Hz and 3117Hz.Deviation meterLPF: 3kHzHPF: OFF
K:503(Reference value)K2:498(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2995~3117Hz
[NXDN Very Narrow]
1) Adj item: [Nv NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Very Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point.(The value is written below.)Transmit at each adjustment point and check that the Analog deviation is between 1311Hz and 1363Hz.Deviation meterLPF: 3kHzHPF: OFF
K:503(Reference value)K2:498(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
1311~1363Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-106 (No.RA054<Rev.001>)
9. DMR High Deviation
1) Adj item: [D DDEV]Adjust: [****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DMR High Deviation (DMR Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the Analog deviation is between 2695Hz and 2803Hz.Deviation meterLPF: 3kHzHPF: OFF
K:503(Reference value)K2:496(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2695~2803Hz
10. QT Deviation
[Analog Wide]
1) Adj item: [Aw QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:520(Reference value)K2:529(Reference value)
0.75kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-107
[Analog Narrow]
1) Adj item: [An QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:520(Reference value)K2:529(Reference value)
0.35kHz±0.05kHz
11. DQT Deviation
[Analog Wide]
1) Adj item: [Aw DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:414(Reference value)K2:426(Reference value)
0.75kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-108 (No.RA054<Rev.001>)
[Analog Narrow]
1) Adj item: [An DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:414(Reference value)K2:426(Reference value)
0.35kHz±0.05kHz
12. LTR Deviation
[Analog Wide]
1) Adj item: [Aw LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:508(Reference value)K2:518(Reference value)
1.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-109
[Analog Narrow]
1) Adj item: [An LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:494(Reference value)K2:518(Reference value)
0.75kHz±0.05kHz
13. DTMF Deviation
[Analog Wide]
1) Adj item: [Aw DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:545(Reference value)K2:542(Reference value)
2.50kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-110 (No.RA054<Rev.001>)
[Analog Narrow]
1) Adj item: [An DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:540(Reference value)K2:542(Reference value)
1.25kHz±0.05kHz
14. Single Tone Deviation
[Analog Wide]
1) Adj item: [Aw TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:514(Reference value)K2:511(Reference value)
3.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-111
[Analog Narrow]
1) Adj item: [An TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:510(Reference value)K2:511(Reference value)
1.50kHz±0.05kHz
15. MSK Deviation
[Analog Wide]
1) Adj item: [Aw MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:503(Reference value)K2:500(Reference value)
3.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-112 (No.RA054<Rev.001>)
[Analog Narrow]
1) Adj item: [An MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:500(Reference value)K2:500(Reference value)
1.50kHz±0.05kHz
16. CWID Deviation
[Analog Narrow]
1) Adj item: [An CWID]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [CWID Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.K:506(Reference value)K2:508(Reference value)
1.10kHz±0.10kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-113
4.26.1 Necessary Deviation adjustment item for each signaling and modeThe following shows the necessary adjustment items for each signaling deviation. Please read the following table like the followingexample. In the case of the signaling "QT (Analog Wide)", this signaling is composed of three elements [Balance, Maximum Deviation(Analog Wide) and QT Deviation (Analog Wide)]. Please adjust Balance and Maximum Deviation (Analog Wide) before adjusting QTDeviation (Analog Wide).
• Balance is common with all the above deviation adjustments. If Balance (Transmitter Section 6) has already adjusted, please skipStep1 and adjust from Step2.
• Maximum Deviation (Analog Wide/Narrow) is common with all the analog signaling deviations and CWID Deviation (NXDN VeryNarrow).If Balance and Maximum Deviation (Analog Wide /Narrow) (Transmitter Section 7) have already adjusted, please skip Step2 andadjust from Step3.
Mode Signaling Necessary adjustment and order
Wide Narrow Very Narrow
Analog Audio 1. Balance adjust2. Maximum Deviation
[Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]
-
QT 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. QT Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. QT Deviation [Analog Narrow]
-
DQT 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. DQT Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DQT Deviation
[Analog Narrow]
-
LTR 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. LTR Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. LTR Deviation [Analog Narrow]
-
DTMF 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. DTMF Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DTMF Deviation [Analog Narrow]
-
2TONE 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. Single Tone Deviation [Analog
Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. Single Tone Deviation
[Analog Narrow]
-
MSK(Fleetsync)
1. Balance adjust2. Maximum Deviation
[Analog Wide]3. MSK Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. MSK Deviation
[Analog Narrow]
-
NXDN Audio - 1. Balance adjust2. NXDN High Deviation
[NXDN Narrow]
1. Balance adjust2. NXDN High Deviation
[NXDN Very Narrow]
CWID - - 1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. CWID Deviation
[Analog Narrow]
DMR Audio - 1. Balance adjust2. DMR High Deviation
-
1-114 (No.RA054<Rev.001>)
4.27 Receiver Section
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. AF level setting
[Panel test mode]1) CH-Sig: 1-1
SSG output: -47dBm (1mV)(MOD: 1kHz/±1.5kHz)
1) Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG output: -47dBm (1mV) (MOD:1kHz/±1.5kHz)
SSGDVMAF VMDummy load
Panel ANTExt. SP connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Volume Up/Down knob to obtain 1.41V AF output.(0.5W @ 4ohm load)
1.41V±0.1V
2. IQ Phase
1) Adj item: [An IQ]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
1) Adj item: [IQ Phase]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]After input signal from SSG,1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment]Adjust RSSI Level(DSP Normal Power Mode)Value to the minimum.
3. RSSI reference [DSP (Receive)]
1) Adj item: [An RSSI 1]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 1 DSP (Receive)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Receive)]
1) Adj item: [An RSSI 2]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 2 RF IC (Receive)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
(No.RA054<Rev.001>)1-115
[DSP (Standby)]
1) Adj item: [An RSSI 3]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 3 DSP (Standby)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Standby)]
1) Adj item: [An RSSI 4]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 4 RF IC (Standby)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
4. Squelch Open
[Analog Wide]
1) Adj item: [Aw SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Open (Analog Wide)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-116 (No.RA054<Rev.001>)
[Analog Narrow]
1) Adj item: [An SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Open (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[NXDN Narrow]
1) Adj item: [Nn SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[NXDN Very Narrow]
1) Adj item: [Nv SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Very Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-117
[DMR] 1) Adj item: [D SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
1) Adj item: [Squelch Open (DMR)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
5. Squelch Tight
[Analog Wide]
1) Adj item: [Aw SQLT]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Tight (Analog Wide)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQLT]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Tight (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-118 (No.RA054<Rev.001>)
6. Low RSSI
1) Adj item: [An LRSSI]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [Low RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
7. High RSSI
1) Adj item: [An HRSSI]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [High RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-119
4.28 NX-3820(G)/3820 E TYPE Controls
4.28.1 Preparations for checking/tuning the transceiverBefore attempting to check/tune the transceiver, connect the unitto a suitable power supply.Whenever the transmitter is turned on, the unit must beconnected to a suitable dummy load (i.e. power meter).The speaker output connector must be terminated with an 4ohmdummy load and connected to an AC voltmeter and an audiodistortion meter or a SINAD measurement meter at all timesduring checking/tuning.
4.29 Panel Test Mode
4.29.1 Test mode operation featuresThis transceiver has a test mode. To enter test mode, press andhold the [ ] button while turning the transceiver power ON orpress the [ ] button and select the "Panel Test". Before thetransceiver enters test mode, the frequency version informationappears on the LCD momentarily. Test mode can be inhibited byprogramming. To exit test mode, turn the transceiver power OFF.The following functions are available in test mode.
• When the panel test mode is activated, the last used channeland signaling numbers are displayed. When the panel testmode is activated for the first time, the channel and signalingnumbers are 1.
4.29.2 Button operation
*1: When the mode is selected as Analog, this function isenabled.
Power switch
Channel Up/Down buttonVolume Up/Down button
MIC jack
KMC-36 (OPTION)
Keypad
[PTT]
Button "Func" not appears on the sub LCD display
Function Display
[+] Push: Volume upHold: Volume up continuously
-
[-] Push: Volume downHold: Volume down continuously
-
[] Push: Test channel upHold: Test channel up continuously
Channel No.
[] Push: Test channel downHold: Test channel down continuously
Channel No.
[] Push: Squelch level up *1Hold: Squelch off
Squelch levelSquelch off: icon appears
[] Wide 5k/Wide 4k/Narrow/Very Narrow
Wide 5k: "w"Wide 4k: "s"Narrow: "n"Very Narrow: "v"
[ ] Shift to panel tuning mode
-
[ ] Function on "Func" appears on the sub LCD display
[ ] Push: Test signaling upHold: Test signaling up continuously
Signaling No.
[ (AUX)] MSK 1200bps and 2400bps *1
2400bps: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
- -
Button "Func" appears on the sub LCD display
Function Display
[+] Function off -
[-] Function off -
[] - -
[] Mode selectionAnalog/NXDN/DMR
Analog: "A"NXDN: "N"DMR: "D"
[] Function off -
[] Button/LCD check The contents of the pressed button etc., appear.
[ ] High power/Medium power/Low power
High:[ ] icon appearsMedium:[ ] icon appearsLow:[ ] icon appears
[ ] Function off -
[ ] External Speaker on/off On: icon appears
1-120 (No.RA054<Rev.001>)
• LED indicatorRed LED Lights during transmission.Green LED Lights when there is carrier.
• Sub LCD indicator"Func" Appears at function on.
• LCD display in panel test mode
4.29.3 Frequency and SignalingThe transceiver has been adjusted for the frequencies shown inthe following table. When required, readjust them following theadjustment procedure to obtain the frequencies you want inactual operation.
(1) Test frequency
(2) SignalingAnalog Type Signaling
[ (AUX)] Compander on/off On: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
Function off -
Button "Func" appears on the sub LCD display
Function Display
(Power ON)
Type Frequency range
400~470MHz
(After 2sec.)
Temperature [oC]Power
An : Analog narrow mode
Aw : Analog wide 5k mode
As : Analog wide 4k mode
Nn : NXDN narrow mode
Nv : NXDN very narrow mode
D : DMR mode
Squelch level
(Analog mode only)
Sub LCD display
Main LCD display Signaling
No.
Channel No.
CH RX (MHz) TX (MHz)
1 435.05000 435.10000
2 400.05000 400.10000
3 469.95000 469.90000
4 435.00000 435.00000
5 435.20000 435.20000
6 435.40000 435.40000
7~16 - -
No. RX TX
1 None None
2 None Square Wave
3 LTR Data LTR Data
4 QT:67.0Hz QT:67.0Hz
5 QT:151.4Hz QT:151.4Hz
6 QT:210.7Hz QT:210.7Hz
7 QT:254.1Hz QT:254.1Hz
8 DQT:D023N DQT:D023N
9 DQT:D754I DQT:D754I
10 DTMF Decode (CODE: 159D)
DTMF Encode (CODE: 159D)
11 None DTMF Encode (CODE: 9)
12 2-tone Decode (A: 304.7Hz, B: 3106.0Hz)
2-tone Encode (A: 304.7Hz,B: 3106.0Hz)
13 Single Tone Decode (979.9Hz)
Single Tone Encode (979.9Hz)
14 None Single Tone Encode (1000Hz)
15 None MSK PN9
16 MSK Decode MSK Encode
(No.RA054<Rev.001>)1-121
NXDN Type Signaling
RAN: Radio Access NumberPN9: Pseudo-Random PatternNo.7, 9 Item: PC test mode only
DMR Type Signaling
4.30 Panel Tuning Mode
4.30.1 Transceiver tuning (To enter tuning mode)To enter tuning mode, press the [ ] button while the transceiveris in test mode. Use the [ (AUX)] button to write tuning datathrough tuning modes, and the [ ]/[ ] button to adjust tuningrequirements (1 to 4096 appears on the LCD).Use the [ ] button to select the adjustment item through tuningmodes. Use the [ ] button to adjust 5, 9 or 17 reference leveladjustments, and use the [ ] button to switch between Wide5k/Wide4k/Narrow.• LCD display in panel tuning mode
4.30.2 Button operation
4.30.3 5, 9 or 17 reference level adjustments frequencyMaximum Transmit Power, High Transmit Power, MediumTransmit Power, Low Transmit Power, IQ Phase, RSSIReference, Squelch Open, Squelch Tight, Low RSSI, HighRSSI
Balance, Maximum Deviation, NXDN High Deviation, DMRHigh Deviation, QT Deviation, DQT Deviation, LTRDeviation, DTMF Deviation, Single Tone Deviation, MSKDeviation, CW ID Deviation
No. RX TX
1 RAN1 RAN1
2 None PN9
3 RAN1 Maximum Deviation Pattern
7 FSW + PN9 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
No. RX TX
1 CC 00 Burst CC 00 Burst
2 PN9 PN9
3 CC 00 Burst Maximum Deviation Pattern
4 CC 00 Burst 1/3 Deviation Pattern
5 CC 00 Burst 0 Continuous Pattern
6 SYNC (Each Slot) +PN9 Burst Pattern
SYNC (Each Slot) + PN9Burst Pattern
7 SYNC (Super Frame) +PN9 Burst Pattern
SYNC (Super Frame) +PN9 Burst Pattern
8 CC 00 Burst 0 Burst Pattern
9 Tone Pattern Tone Test Burst Pattern
10 Silence Pattern Silence Burst Pattern
11 Audio Test Pattern Audio Test Burst Pattern
12 Vocoder Loop None
An AST 2562.6
CV voltage, AD value, etc
Sub LCDdisplay
L1
Adjustment point
Main LCDdisplay Adjustment value
(1~4096)
Proper value guide(When the frequency adjustment is necessary,
or is displayed.)
Adjustment item
An : Analog narrow modeAw : Analog wide 5k modeAs : Analog wide 4k modeNn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
L1L2L3L4L5L6C1C2C3
C4C5H1H2H3H4H5H6
Button Function
Push Hold (1 second)
[+] Volume up Continuation up
[-] Volume down Continuation down
[ ] Adjustment value up Continuation up
[ ] Adjustment value down Continuation down
[ ] Auto adjustment start Output tone pattern change of balance adjustment (A change is possible only during balance adjustment.)
[ ] Wide 5k/Wide 4k/Narrow/NXDN/DMR
-
[ ] Shift to panel test mode -
[ ] To enter 5,9 or 17 reference level adjustments
-
[ ] Go to next adjustment item
Back to last adjustment item (At the time of 5, 9 or 17 point adjustment: Adjustment point change)
[ (AUX)] Writes the adjustmentvalue
-
[PTT](MIC)
Transmit
[0] to [9]and[#],[ ](MIC)
-
Tuning point Display RX (MHz) TX (MHz)
1 L1 400.05000 400.10000
2 L5 417.55000 417.60000
3 C3 435.05000 435.10000
4 H2 452.55000 452.60000
5 H6 469.95000 469.90000
Tuning point Display RX (MHz) TX (MHz)
1 L1 400.05000 400.10000
2 L3 408.85000 408.90000
3 L5 417.55000 417.60000
4 C1 426.35000 426.40000
5 C3 435.05000 435.10000
6 C5 443.85000 443.90000
1-122 (No.RA054<Rev.001>)
VCO Assist
4.30.4 Adjustment item supplement
7 H2 452.55000 452.60000
8 H4 461.35000 461.40000
9 H6 469.95000 469.90000
Tuning point Display RX (MHz) TX (MHz)
1 L1 400.05000 400.10000
2 L2 404.45000 404.50000
3 L3 408.85000 408.90000
4 L4 413.25000 413.30000
5 L5 417.55000 417.60000
6 L6 421.95000 422.10000
7 C1 426.35000 426.40000
8 C2 430.75000 430.80000
9 C3 435.05000 435.10000
10 C4 439.45000 439.50000
11 C5 443.85000 443.90000
12 H1 448.25000 448.30000
13 H2 452.55000 452.60000
14 H3 456.95000 457.10000
15 H4 461.35000 461.40000
16 H5 465.75000 465.80000
17 H6 469.95000 469.90000
Adjustment Item Description
LCD Contrast The contrast of LCD display can be changed.
VCO Assist The lock voltage of VCO is adjusted.This item must be adjusted before receiver and transmitter adjustment items.
Frequency Frequency is adjusted under receivingcondition with SSG.The SSG needs 0.001ppm accuracy soplease use a standard oscillator if necessary.This item can be adjusted only in PC TestMode so that the adjustment value is notchanged easily.
RTC Correction Real Time Clock is adjusted.This item uses the internal clock.(Any measurement equipment is not required.)
Maximum Transmit Power
Maximum Transmit Power is adjusted.
High Transmit Power
High Transmit Power is adjusted.
Mid Transmit Power
Medium Transmit Power is adjusted.
Low Transmit Power
Low Transmit Power is adjusted.
Tuning point Display RX (MHz) TX (MHz)
Ramp Offset Adjust this item to the optimal Ramp voltage.
Balance The transmit modulation frequency response is adjusted.This item is adjusted so that the deviationof 2kHz becomes the same deviation of 20Hz.This item must be adjusted before all adjustment items for deviations are adjusted.
Maximum Deviation(Analog Wide 5k/Wide 4k/Narrow)
Maximum Deviation of Analog (Wide 5k/Wide 4k/Narrow) is adjusted.This item must be adjusted before all adjustment items for tone deviations are adjusted.
High Deviation NXDN/DMR high deviation is adjusted.
QT Deviation QT deviation is adjusted.
DQT Deviation DQT deviation is adjusted.
LTR Deviation LTR deviation is adjusted.
DTMF Deviation DTMF deviation is adjusted.
Single Tone Deviation
The deviation of Single Tone used in “2-tone” and “5-tone” is adjusted.
MSK Deviation MSK deviation is adjusted.
CW ID Deviation CWID tone deviation is adjusted.CWID is used to inform the others who istransmitting on a 6.25-kHz spacing channel.(In FCC rule, Analog mode or CWID isrequired for each channel-spacing.)
IQ Phase Correction of phase difference shift between I and Q.
RSSI Reference The minimum RSSI level for scan stop isadjusted.
Squelch Open The squelch level at level “1” is adjusted.
Squelch Tight The squelch level at level “9” is adjusted.
Low RSSI RSSI display level “ ” is adjusted.Both “Low RSSI” and “High RSSI” must beadjusted. (The curve data of RSSI level isapplied.)
High RSSI
Adjustment Item Description
(No.RA054<Rev.001>)1-123
4.30.5 Adjustment item and Display
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide 5k)
AS(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1 LCD Contrast CNTR - 1 point ADJ CommonSection 21~256
2 VCO Assist AST (CV voltage) - - 17 - - - CommonSection 31~4096
3 RTC Correction RTC - - CommonSection 5-2.00 ~ -0.01 ,0.00 ,+0.01 ~ +2.00
4 Maximum Transmit Power
MAX_P - - - 5 - - - TransmitterSection 11~256
5 High Transmit Power
H_PWR - - - 5 - - - TransmitterSection 21~1024
6 Medium Transmit Power
M_PWR - - - 5 - - - TransmitterSection 31~1024
7 Low Transmit Power
L_PWR - - - 5 - - - TransmitterSection 41~1024
8 Ramp Offset RAMP (ADC measurement value)
1 point ADJ TransmitterSection 51~1024
9 Balance BAL (Encode frequency) - - 9 - - - TransmitterSection 61~1024
10 Maximum Deviation
ADEV - 9 9 9 - - - TransmitterSection 71~1024
11 NXDN High Deviation
NDEV - - - - 9 9 - TransmitterSection 81~1024
12 DMR High Deviation
DDEV - - - - - - 9 TransmitterSection 91~1024
13 QT Deviation QT - 9 9 9 - - - TransmitterSection 101~1024
14 DQT Deviation DQT - 9 9 9 - - - TransmitterSection 111~1024
15 LTR Deviation LTR - 9 9 9 - - - TransmitterSection 121~1024
16 DTMF Deviation DTMF - 9 9 9 - - - TransmitterSection 131~1024
17 Single Tone Deviation
TONE - 9 9 9 - - - TransmitterSection 141~1024
18 MSK Deviation MSK - 9 9 9 - - - TransmitterSection 151~1024
19 CW ID Deviation CWID - - - 9 - - - TransmitterSection 161~1024
20 IQ Phase IQ (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 21~63
21 RSSI Reference 1 DSP (Receive)
RSSI1 (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
1-124 (No.RA054<Rev.001>)
22 RSSI Reference 2 RF IC(Receive)
RSSI2 (RSSI RF IC(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
23 RSSI Reference 3 DSP (Standby)
RSSI3 (RSSI DSP (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
24 RSSI Reference 4 RF IC (Standby)
RSSI4 (RSSI RF IC (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
25 Squelch Open SQL (ASQDET measurement value)
5 5 5 5 5 5 ReceiveSection 41~256
26 Squelch Tight SQLT (ASQDET measurement value)
5 5 5 - - - ReceiveSection 51~256
27 Low RSSI LRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 61~256
28 High RSSI HRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 71~256
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide 5k)
AS(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
(No.RA054<Rev.001>)1-125
4.30.6 Panel tuning mode flow chartNote:
* In this Panel tuning mode flow chart, the Adjustment item name is modified.Panel Test Mode
[ ]hold
LCD Contrast
CNTR
level ecnerefer 9VCO Assist
stnemtsujdAAST
RTC Correction
RTC
Ramp Offset
RAMP
High Power Narrow 5 reference level
H_PWR An Adjustments
Medium Power Narrow 5 reference level
M_PWR An Adjustments
Low Power Narrow 5 reference level
L_PWR An Adjustments
Balance Narrow 9 reference level
BAL An Adjustments
9 reference level
Adjustments
9 reference level
Adjustments
NXDN High Deviation Narrow NXDN High Deviation VeryNarrow
NDEV Nn NDEV Nv
CW ID Deviation Narrow
CWID An
RSSI (Low) Narrow
nAISSRL
RSSI (High) Narrow
nAISSRH
Adjustment Item N/W/VN
LCD Display
For all adjustment items, press the [ ] button
to write the adjustment value.
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]
9 reference level
Adjustments
[ ]
RSSI Referance 1
RSSI1[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]IQ Phase
IQ[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 2
RSSI2[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]RSSI Referance 3
RSSI3[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]
5 reference level
Adjustments
[ ]
5 reference level
Adjustments
[ ]
RSSI Referance 4
RSSI4
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
DMR High Deviation
DDEV
[ ]press [ ]hold
[ ]press [ ]hold
DMR
D
9 reference level
Adjustments
Analog Max Deviation Narrow Analog Max Deviation Wide4k Analog Max Deviation Wide5k
ADEV An ADEV As ADEV Aw
[ ]
[ ] [ ] [ ]
[ ] [ ]
[ ]press [ ]hold
Single Tone Deviation Narrow Single Tone Deviation Wide4k
TONE An TONE Aw[ ] [ ][ ]press [ ]hold
[ ]
MSK Deviation Narrow MSK Deviation Wide4k MSK Deviation Wide5k
MSK An MSK As MSK Aw9 reference levelAdjustments
[ ]
[ ]
QT Deviation Narrow QT Deviation Wide4k
sATQnATQ
DQT Deviation Narrow DQT Deviation Wide4k
DQT An DQT As
LTR Deviation Narrow LTR Deviation Wide4k
sARTLnARTL
DTMF Deviation Narrow DTMF Deviation Wide4k
DTMF An DTMF As
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]9 reference level
[ ]
QT Deviation Wide5k
QT Aw
9 reference levelAdjustments
[ ]
9 reference levelAdjustments
DQT Deviation Wide5k
DQT Aw9 reference levelAdjustments
LTR Deviation Wide5k
LTR Aw
DTMF Deviation Wide5k
DTMF Aw
Adjustments
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
[ ]
9 reference level
[ ]Single Tone Deviation Wide5k
TONE Aw
Adjustments[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]
Squelch (Open) Narrow Squelch (Open) Wide4k Squelch (Open) Wide5k Squelch (Open)
SQL An SQL As SQL Aw SQL
[ ]
[ ] [ ] [ ] [ ] [ ]
[ ] [ ] [ ] [ ]
[ ]
5 reference level
Adjustments
VeryNarrow
NvNarrow
Nn
Squelch (Open)
DMR
D
Squelch (Open)[ ]press [ ]hold
[ ]Squelch (Tight) Narrow Squelch (Tight) Wide4k Squelch (Tight) Wide5k
wATLQSsATLQSnATLQS
5 reference level
Adjustments
[ ] [ ] [ ]
[ ] [ ]
IQ Phase
RSSI Reference 1
RSSI Reference 2
RSSI Reference 3
RSSI Reference 4
Open Squelch
Low RSSI
High RSSI
Tight Squelch
VCO Assist
Maximum Deviation
NXDN High Deviation
DMR High DeviationQT Deviation
DQT Deviation
LTR Deviation
DTMF Deviation
Single Tone Deviation
MSK Deviation
CW ID Deviation
Balance
Adjustment Point
LCD Display
5 reference level
L1
L5
C3
H6
H2
Low 1
Adjustments
Low 5
Center 3
High 6
5 reference level
Adjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]High 2 [ ]
[ ]
[ ]
High Transmit Power
Medium Transmit Power
Low Transmit Power
Adjustment Point
LCD Display
9 reference level
L1
L3
L5
H6
C1
C3
C5
H2
H4
Low 1
Adjustments
Low 3
Low 5
High 6
9 reference level
Adjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Center 1 [ ]
[ ]
Center 3
Center 5
[ ]
[ ][ ]
[ ]High 2 [ ]
[ ]
High 4 [ ]
[ ]
[ ]
Adjustment Point
LCD Display
17 reference level
L1
L2
L3
L4
L5
L6
C1
C2
C3
C4
C5
H1
H2
H3
H4
H5
H6
Low 1
Adjustments
Low 2
Low 3
17 reference level
Adjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Low 4 [ ]
[ ]
Low 5
Low 6
[ ]
[ ][ ]
[ ]Center 1 [ ]
[ ]
Center 2 [ ]
[ ]
Center 3 [ ]
[ ]
Center 4 [ ]
[ ]
Center 5 [ ]
[ ]
High 1 [ ]
[ ]
High 2 [ ]
[ ]
High 3 [ ]
[ ]
High 4 [ ]
[ ]
High 5 [ ]
[ ]
High 6 [ ]
[ ]
[ ]press [ ]hold
Max PowerMAX_P
[ ]press [ ]hold
5 reference level
Adjustments
Narrow
An
[ ]
Maximum Transmit Power
1-126 (No.RA054<Rev.001>)
4.31 Adjustment points
TX-RX UNIT (XC1-183)Component Side
4.32 Test Equipment Required for Alignment
*The test equipment which is not used for adjustment is contained in this table.
RTC (CN55)
RT
C
Test Equipment Major Specifications
1. Standard Signal Generator (SSG)
Frequency RangeModulation Output
100 to 900MHzFrequency modulation and external modulation-127dBm/0.1uV to greater than -20dBm/22.4mV
When performing the Frequency adjustment, the following accuracy is necessary.• 0.001ppmUse a standard oscillator for adjustments, if necessary.
2. Power Meter Input ImpedanceOperation FrequencyMeasurement Capability
50ohm100 to 900MHzVicinity of 100W
3. Deviation Meter Frequency Range 100 to 900MHz
4. Digital Volt Meter (DVM)
Measuring RangeInput Impedance
10mV to 20V DCHigh input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. Frequency Counter Frequency RangeFrequency Stability
10Hz to 1000MHz0.2ppm or less
To measure the oscillating frequency of the internal clock 32766.00Hz~32770.00Hz forRTC Correction Resolution 0.01Hz is better for accuracy adjustment.
7. Ammeter 20A or more
8. AF Volt Meter (AF VM) Frequency RangeVoltage Range
50Hz to 10kHz1mV to 10V
9. Audio Generator (AG) Frequency RangeOutput
50Hz to 5kHz or more0 to 1V
10. Distortion Meter CapabilityInput Level
3% or less at 1kHz50mV to 10Vrms
11. Spectrum Analyzer Measuring Range DC to 1GHz or more
12. 4ohm Dummy Load Approx. 4ohm, 10W
13. Regulated Power Supply 13.2V, approx. 20A (adjustable from 9V to 17V)Useful if ammeter equipped
(No.RA054<Rev.001>)1-127
Test cable for microphone input (E30-3360-28) MIC connector (Front panel view)
Tuning cable (E30-7754-05)Adapter cable (E30-7754-05) is required for injecting an audioif PC tuning is used.See “PC Mode” section for the connection.
4.33 Radio check Section
3
2
4
5
6
7
8
3
1
2
4
5
6
7
8
1GREEN
RED
BLACK
BLUE
SHIELD
WHITE
GRAY
YELLOW
PTT
E
MIC-E
MIC
HK
1 : BLC
2 : +B
3 : GND
4 : PTT/TXD (PC serial data from radio)
5 : MICE
6 : MIC
7 : HOOK/RXD (PC serial data to radio)
8 : DM
1
8
Item Condition Measurement Adjustment Specifications/RemarksPanel test
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Frequency check
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Mode: AnalogSignaling: 1PTT: Press [Transmit] button.
f. counter Panel ANT Check an internal temperature of radio from 20°C to 33°C.
±0.25ppm±[email protected]
2. High power check
1)CH-Sig: 1-1PTT: ONTA: OFF
1)Test ChannelChannel: 1Test Signaling Mode: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 21W~29W10A or less
2)CH-Sig: 2-1PTT: ONTA: OFF
2)Test ChannelChannel: 2Test Signaling Mode: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ONTA: OFF
3)Test ChannelChannel: 3Test Signaling Mode: AnalogSignaling: 1PTT: Press [Transmit] button.
1-128 (No.RA054<Rev.001>)
3. Low power check
1)CH-Sig: 1-1PTT: ONTA: OFF
1)Test ChannelChannel: 1Test Signaling Mode: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 3.5W~6.5W7.0A or less
2)CH-Sig: 2-1PTT: ONTA: OFF
2)Test ChannelChannel: 2Test Signaling Mode: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ONTA: OFF
3)Test ChannelChannel: 3Test Signaling Mode: AnalogSignaling: 1PTT: Press [Transmit] button.
4. MIC sensitivity check
1)CH-Sig: 1-1AG: 1kHzPTT: ON
1)Test ChannelChannel: 1Test Signaling Mode: AnalogSignaling: 1AG: 1kHzPTT: Press [Transmit] button.
DeviationmeterOscilloscopeAGAF VM
Panel ANTMIC jack
Adjust AGinput to get astandardMOD.
5mV ±1mV
5. Sensitivitycheck
1)CH-Sig: 1-1SSG outputWide 5k: -117dBm(0.32μV)(MOD: 1kHz/±3kHz)Wide 4k:-117dBm (0.32μV)(MOD: 1kHz/±2.4kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
1)Test ChannelChannel: 1Test Signaling Mode: AnalogSignaling: 1SSG outputWide 5k: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Wide 4k:-117dBm (0.32μV)(MOD: 1kHz/±2.4kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
SSGAF VMOscilloscopeDistortionmeter4ohmDummy load
Panel ANTExt. SPconnector
Check 12dB SINAD or more
Item Condition Measurement Adjustment Specifications/RemarksPanel test
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-129
4.34 Common Section
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Setting
1) DC voltage:13.2V2) SSG standard modulation
[Wide 5k] MOD:1kHz,DEV:3kHz[Wide 4k] MOD:1kHz,DEV:2.4kHz[Narrow] MOD:1kHz,DEV:1.5kHz
2.LCD Contrast
1) Adj item[CNTR]Adjust:[****]
Press [ ] button to store the adjustment value.
1) Adj item[LCD Contrast]Data: [****]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.
280 (Reference value)
3. VCO Assist
1) Adj item:[AST]Adjust:[****]
2) Adj item:[L1]→[L2]→[L3]→[L4]→[L5]→[L6]→[C1]→[C2]→[C3]→[C4]→[C5]→[H1]→[H2]→[H3]→[H4]→[H5]→[H6]
Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [VCO Assist]
2) Adj item:[Low1],[Low2], [Low3],[Low4],[Low5], [Low6][Center1], [Center2], [Center3], [Center4], [Center5], [High1],[High2][High3],[High4],[High5][High6]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment][V] Indicator on the PC window shows VCO lock voltage. Change the adjustment value to get VCO lock voltage within the limit of the specified voltage.
Note:Confirm the VCO lock voltage approximately 3 seconds after the adjustment value is changed.
2.5V±0.1V[Automatic Adjustment]After the automatic adjustment is performed, verify that the VCO lock voltage is within the voltage range which is specified by the manual adjustment.[Manual Adjustment]Press [Apply] button to store the adjustment value after all adjustment points have been adjusted.Adjustment value range:500 - 1950
1-130 (No.RA054<Rev.001>)
4. Frequency
*The Frequency adjustment can be performed only in PC test mode.
1) Adj item: [Frequency]SSG output: -20dBm (22.4mV) (CW (without modulation))
Caution:Perform the frequency adjustment under the following conditions.
• Temperature range of +20°C to +33°C (+68.0°F to +91.4°F).(The temperature is displayed on the Frequency adjustment screen of the KPG-D3/D3N and the LCD of the transceiver.)
• Use an accuracy of 0.001ppm for the SSG. (Use a standard oscillator if necessary.)
SSG Panel ANT [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode]Press [Start] button of “Auto Tuning”. Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
[PC test mode]“IF20” value = Within 0±30 digits. The value of “IF20” will become around “0” after the adjustment has finished.
Remark:“Frequency” is adjusted under receiving condition with SSG.
5. RTC Correciton
1) Adj item:[RTC]Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [RTC Correction]Data: [****]Press [Apply] button to store the adjustment value.
Frequency Counter
TX-RX
TESTPOINT(CN55)
Remark:The adjustment value should input the display of a Frequency Counter.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-131
4.35 Transmitter Section
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Maximum Transmit Power
1) Adj item:[MAX_P]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maximum Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
57.5W ±2.5W 15A or less
2. High Transmit power
1) Adj item:[H_PWR]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [High Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
25W ±1W10A or less
3. Low Transmit power
1) Adj item:[L_PWR]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Low Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
5W ±0.5W7A or less
1-132 (No.RA054<Rev.001>)
4.Ramp Offset
1)Adj item:[RAMP]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Ramp Offset]Press [Autotune(TX starts)] button. Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune(TX
starts)] button.2) Press [Apply] button
to store the adjustment value after the automatic adjustment has finished.
3) Check Ramp Offset Monitor Value Over 50.
[Manual Adjustment]1) Set the adjustment
value to "1".2) Press [Transmit]
button and increase the adjustment value slowly while monitoring the offset monitor value.
3) Set the adjustment value when the offset monitor value exceed "60".
5. Balance
1) Adj item: [An BAL]Adjust:[****]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Balance]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
The Deviation of 20Hz frequency is fixed.Change the 2kHz adjustment value to become the same deviation of 20Hz within the specified range.[Panel tuning mode]PTT:ONWhile PTT:ON, press the [] button to change the 20Hz/2kHz.[PC test mode]PTT: Press [Transmit] button.While PTT:ON, click the check box "2kHz Sine Wave" to change the 20Hz/2kHz.
2kHz Tone deviation is within ± 1.0% of 20Hz tone deviation.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-133
6. Maximum Deviation
[Analog Wide 5k]
1) Adj item: [Aw ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2V]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the deviation is between 4150Hz and 4250Hz.Deviation meterLPF: 15kHzHPF: OFF
496(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
4150~4250Hz
[Analog Wide 4k]
1) Adj item: [As ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2V]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the deviation is between 3310Hz and 3410Hz.Deviation meterLPF: 15kHzHPF: OFF
496(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
3310~3410Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-134 (No.RA054<Rev.001>)
[Analog Narrow]
1) Adj item: [An ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the deviation is between 2050Hz and 2150Hz.Deviation meterLPF: 15kHzHPF: OFF
493(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2050~2150Hz
7. NXDN High Deviation[NXDN Narrow]
1) Adj item: [Nn NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the Analog deviation is between 2995Hz and 3117Hz.Deviation meterLPF: 3kHzHPF: OFF
498(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2995~3117Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-135
[NXDN Very Narrow]
1) Adj item: [Nv NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Very Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the Analog deviation is between 1331Hz 1311Hz and 1363Hz.Deviation meterLPF: 3kHzHPF: OFF
498(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
1311~1363Hz
8. DMR High Deviation
1) Adj item: [D DDEV]Adjust: [****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DMR High Deviation (DMR Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value for each adjustment point. (The value is written below.) Transmit at each adjustment point and check that the Analog deviation is between 2695Hz and 2803Hz.Deviation meterLPF: 3kHzHPF: OFF
496(Reference value)
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2695~2803Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-136 (No.RA054<Rev.001>)
9. QT Deviation
[Analog Wide 5k]
1) Adj item: [Aw QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.529(Reference value)
0.75kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.529(Reference value)
0.60kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-137
[Analog Narrow]
1) Adj item: [An QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.529(Reference value)
0.35kHz±0.05kHz
10. DQT Deviation
[Analog Wide 5k]
1) Adj item: [Aw DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.426(Reference value)
0.75kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-138 (No.RA054<Rev.001>)
[Analog Wide 4k]
1) Adj item: [As DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.426(Reference value)
0.60kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.426(Reference value)
0.35kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-139
11. LTR Deviation
[Analog Wide 5k]
1) Adj item: [Aw LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.518(Reference value)
1.00kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.518(Reference value)
0.90kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-140 (No.RA054<Rev.001>)
[Analog Narrow]
1) Adj item: [An LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.518(Reference value)
0.75kHz±0.05kHz
12. DTMF Deviation
[Analog Wide 5k]
1) Adj item: [Aw DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.542(Reference value)
2.50kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-141
[Analog Wide 4k]
1) Adj item: [As DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.542(Reference value)
2.00kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.542(Reference value)
1.25kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-142 (No.RA054<Rev.001>)
13. Single Tone Deviation
[Analog Wide 5k]
1) Adj item: [Aw TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.511(Reference value)
3.00kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.511(Reference value)
2.40kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-143
[Analog Narrow]
1) Adj item: [An TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.511(Reference value)
1.50kHz±0.05kHz
14. MSK Deviation
[Analog Wide 5k]
1) Adj item: [Aw MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.500(Reference value)
3.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-144 (No.RA054<Rev.001>)
[Analog Wide 4k]
1) Adj item: [As MSK]Adjust:[****][L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.500(Reference value)
2.40kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.500(Reference value)
1.50kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-145
15. CWID Deviation
[Analog Narrow]
1) Adj item: [An CWID]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3]→[C5]→[H2]→[H4]→[H6]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [CWID Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.508(Reference value)
1.10kHz±0.10kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-146 (No.RA054<Rev.001>)
4.35.1 Necessary Deviation adjustment item for each signaling and modeThe following shows the necessary adjustment items for each signaling deviation. Please read the following table like the followingexample. In the case of the signaling "QT (Analog Wide 5k)", this signaling is composed of three elements [Balance, MaximumDeviation (Analog Wide 5k) and QT Deviation (Analog Wide 5k)]. Please adjust Balance and Maximum Deviation (Analog Wide 5k)before adjusting QT Deviation (Analog Wide 5k).
• Balance is common with all the above deviation adjustments. If Balance (Transmitter Section 6) has already adjusted, please skipStep1 and adjust from Step2.
• Maximum Deviation (Analog Wide 5k/Wide 4k/Narrow) is common with all the analog signaling deviations and CWID Deviation(NXDN Very Narrow).If Balance and Maximum Deviation (Analog Wide 5k/Wide 4k /Narrow) (Transmitter Section 7) have already adjusted, please skipStep2 and adjust from Step3.
Mode Signaling Necessary adjustment and order
Wide 5k Wide 4k Narrow Very Narrow
Analog Audio 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]
-
QT 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. QT Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. QT Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. QT Deviation
[Analog Narrow]
-
DQT 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. DQT Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. DQT Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DQT Deviation
[Analog Narrow]
-
LTR 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. LTR Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. LTR Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. LTR Deviation
[Analog Narrow]
-
DTMF 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. DTMF Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. DTMF Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DTMF Deviation
[Analog Narrow]
-
5TONE 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. Single Tone Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. Single Tone Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. Single Tone Deviation
[Analog Narrow]
-
MSK(Fleetsync)
1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. MSK Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. MSK Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. MSK Deviation
[Analog Narrow]
-
NXDN Audio - - 1. Balance adjust2. NXDN High Deviation
[NXDN Narrow]
1. Balance adjust2. NXDN High
Deviation [NXDN Very Narrow]
CWID - - - 1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. CWID Deviation
[Analog Narrow]
DMR Audio - - 1. Balance adjust2. DMR High Deviation
-
(No.RA054<Rev.001>)1-147
4.36 Receiver Section
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. AF level setting
[Panel test mode]1) CH-Sig: 1-1
SSG output: -47dBm (1mV)(MOD: 1kHz/±1.5kHz)
1) Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG output: -47dBm (1mV) (MOD:1kHz/±1.5kHz)
SSGDVMAF VMDummy load
Panel ANTExt. SP connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Volume Up/Down knob to obtain 1.41V AF output.(0.5W @ 4ohm load)
1.41V±0.1V
2. IQ Phase
1) Adj item: [An IQ]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
1) Adj item: [IQ Phase]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]After input signal from SSG,1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment]Adjust RSSI Level(DSP Normal Power Mode)Value to the minimum.
3. RSSI reference [DSP (Receive)]
1) Adj item: [An RSSI 1]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 1 DSP (Receive)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Receive)]
1) Adj item: [An RSSI 2]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 2 RF IC (Receive)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
1-148 (No.RA054<Rev.001>)
[DSP (Standby)]
1) Adj item: [An RSSI 3]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 3 DSP (Standby)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Standby)]
1) Adj item: [An RSSI 4]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 4 RF IC (Standby)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
4. Squelch Open
[Analog Wide 5k]
1) Adj item: [Aw SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Open (Analog Wide 5k)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-149
[Analog Wide 4k]
1) Adj item: [As SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±2.4kHz)
1) Adj item: [Squelch Open (Analog Wide 4k)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±2.4kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Open (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[NXDN Narrow]
1) Adj item: [Nn SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-150 (No.RA054<Rev.001>)
[NXDN Very Narrow]
1) Adj item: [Nv SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Very Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[DMR] 1) Adj item: [D SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
1) Adj item: [Squelch Open (DMR)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
5. Squelch Tight
[Analog Wide 5k]
1) Adj item: [Aw SQLT]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Tight (Analog Wide 5k)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA054<Rev.001>)1-151
[Analog Wide 4k]
1) Adj item: [As SQLT]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±2.4kHz)
1) Adj item: [Squelch Tight (Analog Wide 4k)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±2.4kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQLT]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Tight (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
6. Low RSSI
1) Adj item: [An LRSSI]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [Low RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
7. High RSSI
1) Adj item: [An HRSSI]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [High RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-152 (No.RA054<Rev.001>)
SECTION 5TROUBLESHOOTING
5.1 Fault Diagnosis of the BGA (Ball Grid Array) IC
OverviewA flowchart for determining whether or not the transceiver can be powered on (the LCD does not function even if the power switch isturned on) due to broken BGA parts.
BGA partsMPU/DSP(IC404), mobile DDR(IC402), Flash Memory(IC401)When the BGA IC is problematic, please bring the printed circuit board (XCA-033K-00/XCA-033E-01/XCA-034K-00/XCA-034K-01/XCA-034E-01) in for service. Various ESN/ default adjustment values are written on the printed cicuit board for service.Additionally various ESN stickers are included. (Please refer to "5.4 Replacing TX-RX Unit".)After the printed circuit board has been readjusted, please attach any ESN stickers to the chassis. When "ESN Validation" is used,youmust modify the ESN register.
Checking power supply voltage
Checking voltage
Points to be checked
Points to be checked
Points to be checked
Points to be checked Confirmed voltage
/IGN_OUT IC22(9pin) ON: 0V
OFF: 0V 3.1V
The ignition key is kept ON.
Points to be checked Confirmed voltage
/PSW_OUT IC22(15pin) ON: 0V
OFF: 0V 3.1V
Normal voltage
Normal voltage
1.2V
19.2MHz
12M C401.8V 18M C573.2V
1.8V3.1V
32M IC20(5pin)1.8V18M_3 IC21(1pin)
Power supply of each device is connected through the coil.[MPU/DSP]12M: L405, L406, L40818M: L410, L41132M: L412
[mobile DDR]18M: L403
[Flash Memory]
32M: L401
18M_3: L413
Checking the clock
Checking the clock
Normal voltage (1.2V)
19.2MHzMPU/DSP side R424
Pass
Pass
Pass
Pass
Checking the Reset/Control signal
Checking the control signal input to the MPU/DSP
/RST D14(Anode side)/BINT2 CN17
The POWER key is pressed and held.
Checking the MPU/DSP input switch signal
The BGA parts are not broken.
The BGA parts are not broken.
Checking for an abnormal point
12M has an abnormal voltage.[MPU/DSP]Remove L405 and L406 and L408 to check the
voltage of the 12M.
If the voltage becomes normal, the MPU/DSP is
broken.
Note: IC24(12M DC/DC Converter Device) is
fragile in the scratch.
Be careful when you touch this parts.
[MPU/DSP]
Check the peripheral circuit of IC2.*2
Fail
Fail
Fail
Fail
/OVRB_OUT IC22(12pin) 3.1V
Remove L410 and L411 to check the voltage
of the 18M.
If the voltage becomes normal, the MPU/DSP
is broken.
[mobile DDR]
Remove L403 to check the voltage of the 18M.
If the voltage becomes normal, the mobile DDR
is broken.
32M has an abnormal voltage.
[MPU/DSP]
Remove L412 to check the voltage of the 32M.
If the voltage becomes normal, the MPU/DSP
is broken.
[Flash Memory]
Remove L401 to check the voltage of the 32M.
If the voltage becomes normal, Flash memory
is broken.
If the voltage is not corrected, there is a problem
other than the BGA parts.*1
18M_3 has an abnormal voltage.
[Flash memory]
Remove L413 to check the voltage of the 18M_3.
If the voltage becomes normal, Flash memory is
broken.
18M has an abnormal voltage.
(No.RA054<Rev.001>)1-153
Checking the output signal
from the MPU/DSP.
Fail
Fail
Fail
Pass
Points to be checked Normal voltageSBC MPU/DSP side R62 3.2V
Remove R62 to check the voltage of the SBC.
If the MPU/DSP side is 0V,
the MPU/DSP or Flash memory or mobile DDR
may be broken.
Fail
Fail
Fail
Pass
Pass
Pass
Pass
The LCD displays control
The LCD displays control
It is unlikely that the BGA parts are broken.
Points to be checked Normal voltagePRST
D410(Cathode side)
3.2V
Points to be checked Normal voltage
/FRST
D401(Anode side)
Points to be checked Normal voltage
/CS_LCD CP412(8pin)
After power-on,
and
1.8V fixed later
1.8V 0V 1.8V,
After power-on,
and
/CS_LCD has an abnormal voltage.
Check each of the following items.
Check to see the terminal of L419 and CP412.
Remove the FFC of TX-RX unit between
Sub (Display) Unit.
As a result, if the abnormality yet, the MPU/DSP or
Flash memory or mobile DDR may be broken.
Remove Q403.
If the MPU/DSP side is 3.2V, the MPU/DSP or Flash
memory or mobile DDR may be broken.
Points to be checked Normal voltage54M C520
18M C519
32M C511
5.36V
1.8V
3.2V
The BGA parts are not broken.
Remove the FFC of TX-RX unit between Sub
(Display) unit.
If the voltage becomes normal, the FFC or Sub
(Display) unit is broken.
The LCD display “INIT ERROR 1”.An error occurs when the mobile DDR internal
RAM reads or writes.
The mobile DDR may be broken.
Check the flowchart from beginning.
1) /RST : MPU/DSP reset signal LOW Reset
2) /BINT : Battery final voltage monitoring LOW Final voltage
3) /OVRB_OUT : Battery overvoltage monitoring LOW Overvoltage
4) /PSW_OUT : Power switch signal LOW ON
5) /IGN_OUT : Ignition switch signal LOW ON
6) /FRST : Flash Memory reset signal HIGH Reset
7) /CS_F : Flash Memory chip select signal LOW Active
10) /CS_LCD : LCD controller chip select signal LOW Active
9) PRST : LCD reset signal HIGH Reset
8) SBC : Switch +B control HIGH ON
1.8V
1.8V fixed later
Checking the control signal output from the MPU/DSP
Remove D401 to check the voltage of Flash memory
side R433.
If the voltage becomes abnormal, Flash memory is
broken.
If the /FRST is always 0V, the MPU/DSP is broken.
Pass
Points to be checked Normal voltage
/CS_F IC403(4pin)
If the IC403 (1pin) is 0V or 1.8V,
the MPU/DSP may be broken.
If the IC403 (2pin) is 0V or 1.8V,
the MPU/DSP or Flash memory may be broken.
1.8V 0V 1.8V,
Pass
When an error display appears on the LCD
Descriptions of signal names
1-154 (No.RA054<Rev.001>)
Checking the operation of the MSP430When VIN of 54M
is 0V.
Pass
Pass
Check that the signal BAT_CNT
of MSP430(IC22 - 7pin) outputs High(3.1V). 54M(IC25) or its peripheral circuit is broken.
Fail
Fail
Pass
When the signal /OVRB_OUT has an abnormal outputs,
check that the /OVRB(IC22 - 2pin) is High(3.1V) in the
deck powered on.
MSP430 or its peripheral circuit is broken.
MSP430 is broken.
Checking the operation of MSP430 (/OVRB_OUT)
Pass
Fail
When the signal /RST(IC22 - 14pin) has an
abnormal output, check that the analog voltage of
/RST(IC22 - 6pin) is normal.(typically 2.7V.
Minimum detection voltage is 2.0V.).
MSP430 is broken.
MSP430, 54M(IC25) or its peripheral circuit of is
broken.
Pass
Fail
Check that the analog voltage
of /BINT(IC22 - 5pin) is normal(typically 2.6V.
Operating voltage range is 1.6V~3.0V).
MSP430 is broken.
Pass
Pass
Checking the operation of the MSP430 (/RST)
Checking the operation of MSP430 (/BINT)
Check that the voltage of VIN of 54M(IC25 - 8pin)
is 13.6V.
Standard Voltage/Operating Voltage range
K Type 13.6V/13.6 15%
E type 13.2V/10.8V~15.6V.
Set the supply voltage within the operating voltage
range. If set correctly, MSP430 or its peripheral
circuit is broken.
Set the supply voltage within the operating voltage
range. if set correctly, 54M(IC25) or its peripheral
circuit is broken.
When the signal /BINT(IC22 - 13pin) has an abnormal
outputs, check that the signal /RST(IC22 - 14pin) has
correct output.
MSP430 or its peripheral circuit of is broken.
Check the voltage (13.6V[operating voltage range])
at both ends of F1(fuse). If F1 is broken, replace the
F1 with a new one. If F1 is not broken, 54M(IC25) or
its peripheral circuit is broken.
Fail
Check that the voltage of DVCC of MSP430(IC22 - 1pin)
is 3.1V.
MSP430, 31BU, 50BU or one of these peripheral
circuit is broken.
When VIN of 54M is
out of operating
voltage range.
If 12M, 18M or 32M has still an abnormal voltage after the implementation of each procedure above,
54M(IC25),12M(IC24),18M(IC12),32M(IC20) or one of these peripheral circuit is broken.
54M(normally 5.4V at L13) has an abnormal voltage, check the MSP430(IC22) according to the following procedure.
*1
*2
(No.RA054<Rev.001>)1-155
When /IGN is 0V and
/IGN_OUT is not 0V.
When both /IGN and
/IGN_OUT are not 0V.
When the ignition sense has 13.6V(set within the
operating voltage range), check that the signal
/IGN and IGN_OUT are 0V.
MSP430 is broken.
MSP430 or the circuit of the signal /IGN is broken.
If the ignition function is enabled,
check that the signal /IGN(IC22 - 8pin) and /IGN_OUT(IC22 - 9pin) are linked with the ignition sense.
When /PSW is linked
and /PSW_OUT is not
linked with the power button.
When both /PSW and /PSW_OUT are
not linked with the power button.
Check that the signal /PSW and /PSW_OUT are 0V
during the power button is pressed.MSP430 is broken.
MSP430 or the circuit of the signal /PSW is broken.
Check that the signal /PSW(IC22 - 10pin) and /PSW_OUT(IC22 - 15pin) are linked
with the power button on KCH-19 in power on state.
Checking the operation of MSP430 (/PSW and /IGN)
A. When MSP430(IC22) is replaced, IC22 must be replaced to "MSP430G25KGCA"(This MSP430 is written the program.).
B. OMAP communicates with MSP430 by serial communication at startup of deck.
Only firmware version of MSP430 is confirmed by OMAP in serial communication.
Even when firmware version of MSP430 can not be acquired, the system of MSP430 is started.
C. If there is the difference of firmware version of MSP430 between MSP430 and OMAP,
the firmware version of MSP430 is updated with the serial communication by OMAP.
"WAIT..." is displayed on the LCD during the firmware update. When the firmware update fails,
the system of MSP430 is started and OMAP is trying to update again at next startup.
Remarks related to MSP430
1-156 (No.RA054<Rev.001>)
5.2 Failure diagnosis of the GPS section (GPS model only)
Overview:When the GPS function does not operate, use this flowchart to determine the problem.
Fail
Pass
Pass
MPU/DSP
IC
Level
Conversion
IC
Level
Conversion
IC
TCXO
19.2MHz
BT/GPS
IC
RF
Matching
SAW
Filter
GPS
Antenna
Bias
32.768KHz
Clock
GPS Antenna unitL9IC5IC6
Coaxial
cableX2X1
IC7
IC404
UART
PCM
UART
TX-RX UNIT
BT/GPS UNIT
CN5
PCM PCM
UART
Major parts for a GPS circuit
• Coaxial cable: E0E-0003-00
• GPS active antenna: KRA-40 (option)
• SAW Filter (L9)
• Bluetooth/GPS IC (IC5)
• Level conversion IC (IC6, IC7)
• TCXO 19.2MHz (X1)
• 32.768 kHz clock (X2)
• 33BT Regulator (IC3)
• 18BT Regulator (IC2)
• 33GPS Regulator (IC4)
• MPU/DSP IC (IC404)
Positioning is not carried out normally.
Power is not supplied to the KRA-40. When the power supply is turned ON, Displayed
“GPS ANT FAIL” is displayed
Not displayed
Fail Verify the connection of KRA-40.
(SMA connector)
Pass
Verify the connection of the SMA
connecting cable.
CN5 – E0E-0003-00
Pass
Fail
Check the BT/GPS UNIT PCB side A.
FailConnect the KRA-40
correctly.
Connect the cable to
the CN5 correctly.
Check the BT/GPS UNIT PCB side B.
CN5 – E0E-0003-00
Verify the connection of the SMA
connecting cable.
Verify the connection of KRA-40.
(SMA connector)
(No.RA054<Rev.001>)1-157
Pass
Check the BT/GPS UNIT PCB side A.
Pass
Verify the BT/GPS power Fail
supply.
(33BT) L4: 3.3V
Pass
Verify the BT/GPS power
supply.
(18BT) L5: 1.8V
Pass
Fail
FailVerify the RTC for the
BT/GPS.
X2 (3 pin): Square waveform,
32.768 kHz, 1.8Vp-p
Pass
Fail
Verify the reference clock for
the BT/GPS.
(BT_CLK) Intersection of C8
and C9: Sine waveform,
19.2MHz, 0.2 to 1.2 Vp-p
Pass
Check the BT/GPS UNIT PCB side B.
Check the BT/GPS UNIT PCB side B.
Pass
Fail
Fail
[The BT/GPS power supply
line 33BT circuit is faulty]
Verify the PCB side A parts.
L4, C15, C19, C20, C33
Replace any abnormal parts.
[The BT/GPS power supply
line 18BT circuit is faulty]
Verify the PCB side A parts.
C18, C13, C31, L8, C39
Replace any abnormal parts.
Check the BT/GPS UNIT
PCB side B (a).
Check the BT/GPS UNIT
PCB side B (b).
Verify the RTC line circuit for
the BT/GPS.
X2, L8, C39
Replace any abnormal parts.
[The reference clock circuit
for the BT/GPS is faulty]
Verify the R9, Q1, R10, R26,
R12, R13, X1, C4, C8, C9
Replace any abnormal parts.
Fail Verify the BT/GPS power
supply.
(33GPS) L6: 3.3V
Fail
Fail
Verify the power supply voltage
after removing the KRA-40.
(33GPS) L6:3.3V
[The BT/GPS power supply
line 33GPS circuit is faulty]
C7, C23, C24, R15, C25, R16,
R19, C26, C27, C29, L2, R14,
C3
Replace any abnormal parts.
[The KRA-40 may be
broken]
Replace the KRA-40
[The BT/GPS IC is
abnormal]
Replace the PCB.
[The GPS RF input circuit is faulty]
Replace the GPS RF input circuit
parts. (only the parts which can be
replaced) If any unexchangeable
parts are abnormal, replace the PCB.
Fail
Verify the RF input circuit for the GPS.
SAW, GPS IC RF Matching
From connecter to SAW: CN5, C40, R24, R23
SAW parts: L9, D17, D18
GPS IC RF Matching parts: C38, C36, L7
1-158 (No.RA054<Rev.001>)
Pass
Pass
Pass
Pass
Pass
Pass
Fail
Verify the BT/GPS control
signal
(BTFM_nSHUTDoWN).
IC1 (5pin): 1.8V
Pass
Verify the BT/GPS control
signal (18BT_RX).
IC6 (7pin):
Square waveform UART data
of 1.8V logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
Fail
Fail
Verify the BT/GPS control
signal (RXD2).
CN1 (7pin): Square
waveform UART data of 3.3V
logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
[The BT/GPS IC is
abnormal]
Replace the PCB.
FailCheck the TX-RX UNIT
PCB
Verify the BT/GPS control
signal (/BT_SHUTDOWN).
CN1 (14pin): 3.3V
[/BT_SHUTDOWN line circuit
is faulty]
Verify the IC1, R7
Replace any abnormal parts.
Fail
Verify the BT/GPS control
signal (TXD2).
CN1 (6pin):
Square waveform UART data
of 3.3V logic.
Check the TX-RX UNIT
PCB
Check the TX-RX UNIT
PCB
Fail
[The 18BT_HCI_RX (TXD2)
line circuit is faulty]
Verify the CP1, IC6, R22
Replace any abnormal parts.
Verify the BT/GPS control
signal (18BT_HCI_TX).
IC6 (8pin):
Square waveform UART data
of 1.8V logic.
[The RXD2 (18BT_HCI_TX)
line circuit is faulty]
Verify the CP1, IC6, R22
Replace any abnormal parts.
(No.RA054<Rev.001>)1-159
Pass
Check the PCB side B (a).
Pass
Fail [The BT/GPS IC is
abnormal]
Replace the PCB.
[The BT/GPS power supply line 33BT circuit is
faulty]
Verify the PCB side B parts.
C5, C46, C44, C49
Replace any abnormal parts.
Check the PCB side B (b).
Fail [The BT/GPS IC is
abnormal]
Replace the PCB.
[The BT/GPS power supply line 18BT circuit is
faulty]
Verify the PCB side A parts.
C2, C47, L5, L13, C45, C48
Replace any abnormal parts.
1-160 (No.RA054<Rev.001>)
Pass
Pass
Pass
Pass
Pass
Check the TX-RX UNIT PCB
Fail
Verify the BT/GPS control
signal (TXD2).
CN2 (15pin): Square
waveform UART data of 3.3V
logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
Fail
Verify the BT/GPS control
signal (RXD2).
CN2 (14pin): Square
waveform UART data of 3.3V
logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
[The MPU/DSP IC is
abnormal]
Replace the PCB.
Descriptions of signal names
1) 33BT: BT/GPS IC 3.3V power supply
2) 18BT: BT/GPS IC 1.8V power supply
3) 33GPS: BT/GPS IC 3.3V power supply
4) TXD2: BT/GPS serial data line connected to UART TX of MPU/DSP IC (MPU/DSP to BT/GPS IC)
5) RXD2: BT/GPS serial data line connected to UART RX of MPU/DSP IC (MPU/DSP to BT/GPS IC)
6) 18BT_HCI_RX: BT/GPS serial data line connected to UART RX of BT/GPS IC (MPU to BT/GPS IC)
7) 18BT_HCI_TX: BT/GPS serial data line connected to UART TX of GPS IC (BT/GPS IC to MPU)
8) /BT_SHUTDOWN: BT/GPS active control of MPU/DSP IC (MPU/DSP to BT/GPS IC) High Reset Active, Low
Fail
Fail
Verify the BT/GPS control
signal
CP405 (3pin):
Square waveform UART data
of 3.3V logic.
[The RXD2 (18BT_HCI_TX)
line circuit is faulty]
Verify the CP405
Replace any abnormal parts.
Verify the BT/GPS control
signal (18BT_HCI_TX).
CP405, (4pin):
Square waveform UART data
of 1.8V logic.
[The RXD2 (18BT_HCI_TX)
line circuit is faulty]
Verify the CP405
Replace any abnormal parts.
[The MPU/DSP IC or
unchangeable part is
abnormal]
Replace the PCB.
[The MPU/DSP IC or
unchangeable part is
abnormal]
Replace the PCB.
(No.RA054<Rev.001>)1-161
5.3 Failure diagnosis of the Bluetooth section
Overview:When the Bluetooth function does not operate, use this flowchart to determine the problem.
No
Pass
Pass
Pass
Pass
Pass
Pass
X2X1
Major parts for a Bluetooth circuit TX-RX Unit BT/GPS UnitIC404
UART
MPU/DSPIC
PCM PCM
Power
UART
IC6 IC5
UART
5.4V
BluetoothAntenna
GPSAntenna
L11
LCFilter
L9
BPF
32.768kHzClock
BT/GPSIC
PCM
Level conversion
IC
IC7
Level conversion
IC
IC2, IC3, IC4
TCXO
19.2MH
1.8V
3.3V
3.3V
Voltage regulator
Charge the BT headset. Turn on your BT headset and bring it
within one meter.
Try again pair with BT headset.
• Bluetooth antenna (Pattern Antenna)
• LC filter (L11)
• Bluetooth/GPS IC (IC5)
• Level conversion IC (IC6, IC7)
• TCXO 19.2MHz (X1)
• 32.768 kHz clock (X2)
• 33BT Regulator (IC3)
• 18BT Regulator (IC2)
• MPU/DSP IC (IC404: TX-RX Unit)
I can not pair with the Bluetooth (BT) headset.
Is the BT headset charged enough?
Is the BT headset turned on?
Is the BT headset in pairing mode?
Check the BT/GPS UNIT PCB side A.
Check the BT/GPS UNIT PCB side A.
FailVerify the antenna matching
parts.
Visually check to L15, C68
Verify the BT/GPS power
supply.
(33BT) L4: 3.3V
FailVerify the BT/GPS power
supply.
(18BT) L5: 1.8V
Fail
FailVerify the RTC for the
BT/GPS.
X2 (3 pin): Square waveform,
32.768 kHz, 1.8Vp-p
Replace any abnormal parts.
[The BT/GPS power supply Fail
line 33BT circuit is faulty]
Verify the PCB side A parts.
L4, C15, C19, C20, C33
Replace any abnormal parts.
Check the BT/GPS UNIT
PCB side B (a).
Check the BT/GPS UNIT
PCB side B (b).
Fail[The BT/GPS power supply
line 18BT circuit is faulty]
Verify the PCB side A parts.
C18, C13, C31, L8, C39
Replace any abnormal parts.
Verify the RTC line circuit for
the BT/GPS.
X2, L8, C39
Replace any abnormal parts.
1-162 (No.RA054<Rev.001>)
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Fail
Verify the reference clock for
the BT/GPS.
(BT_CLK) Intersection of C8
and C9: Sine waveform,
19.2MHz, 0.2 to 1.2 Vp-p
Check the BT/GPS UNIT PCB side B.
[The reference clock circuit
for the BT/GPS is faulty]
Verify the R9, Q1, R10, R26,
R12, R13, X1, C4, C8, C9
Replace any abnormal parts.
Check the BT/GPS UNIT PCB side B.
Verify the ANT Matching
Parts.
Visually check to R27, R29
Fail
Fail
Verify the BT/GPS control
signal
(BTFM_nSHUTDoWN).
IC1 (5pin): 1.8V
Fail
Verify the BT/GPS control
signal (18BT_RX).
IC6 (7pin):
Square waveform UART data
of 1.8V logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
Replace any abnormal parts.
Verify the BT/GPS control
signal (/BT_SHUTDOWN).
CN1 (16pin): 3.3V Fail
[/BT_SHUTDOWN line circuit
is faulty]
Verify the IC1, R7
Replace any abnormal parts.
Fail
Verify the BT/GPS control
signal (TXD2).
CN1 (6pin):
Square waveform UART data
of 3.3V logic.
[The 18BT_HCI_RX (TXD2)
line circuit is faulty]
Verify the CP1, IC6, R22
Replace any abnormal parts.
Check the TX-RX UNIT
PCB.
Check the TX-RX UNIT
PCB.
(No.RA054<Rev.001>)1-163
Pass
Pass
Pass
Pass
Pass
Fail
Verify the BT/GPS control
signal (RXD2).
CN1 (7pin): Square
waveform UART data of 3.3V
logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
[The BT/GPS IC is
abnormal]
Replace the PCB.
Check the PCB side B (a).
[The BT/GPS power supply line 33BT circuit is
faulty]
Verify the PCB side B parts.
C5, C46, C44, C49
Replace any abnormal parts.
Fail
Check the PCB side B (b).
Fail[The BT/GPS power supply line 18BT circuit is
faulty]
Verify the PCB side A parts.
C2, C47, L5, L13, C45, C48
Replace any abnormal parts.
Fail
Verify the BT/GPS control
signal (18BT_HCI_TX).
IC6 (8pin):
Square waveform UART data
of 1.8V logic.
[The RXD2 (18BT_HCI_TX)
line circuit is faulty]
Verify the CP1, IC6, R22
Replace any abnormal parts.
Check the TX-RX UNIT
PCB.
[The BT/GPS IC is
abnormal]
Replace the PCB.
[The BT/GPS IC is
abnormal]
Replace the PCB.
1-164 (No.RA054<Rev.001>)
Pass
Pass
Pass
Pass
Pass
Check the TX-RX UNIT PCB
Verify the BT/GPS control
signal (TXD2).
CN735 (15pin): Square
Fail
waveform UART data of 3.2V
logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
Fail
Verify the BT/GPS control
signal (G_TXD2).
CP705 (3pin):
Square waveform UART data
of 3.2V logic.
[The RXD2 (18BT_HCI_TX)
line circuit is faulty]
Verify the CP705
Replace any abnormal parts.
Fail
Verify the BT/GPS control
signal (18BT_HCI_TX).
CP705, (4pin):
Square waveform UART data
of 1.8V logic.
[The RXD2 (18BT_HCI_TX)
line circuit is faulty]
Verify the CP705
Replace any abnormal parts.
[The MPU/DSP IC is
abnormal]
Replace the TX-RX PCB.
[The MPU/DSP IC is
abnormal]
Replace the TX-RX PCB.
Fail
Verify the BT/GPS control
signal (RXD2).
CN735 (14pin): Square
waveform UART data of 3.3V
logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
[The BT/GPS IC is
abnormal]
Replace the PCB.
Descriptions of signal names
1) 33BT: BT/GPS IC 3.3V power supply
2) 18BT: BT/GPS IC 1.8V power supply
3) TXD2: BT/GPS serial data line connected to UART TX of MPU/DSP IC (MPU/DSP to BT/GPS IC)
4) RXD2: BT/GPS serial data line connected to UART RX of MPU/DSP IC (MPU/DSP to BT/GPS IC)
5) 18BT_HCI_RX: BT/GPS serial data line connected to UART RX of BT/GPS IC (MPU to BT/GPS IC)
6) 18BT_HCI_TX: BT/GPS serial data line connected to UART TX of GPS IC (BT/GPS IC to MPU)
7) /BT_SHUTDOWN: BT/GPS active control of MPU/DSP IC (MPU/DSP to BT/GPS IC) High Active, Low Reset
(No.RA054<Rev.001>)1-165
5.4 Replacing TX-RX Unit
TX-RX unit Information
Method of confirming “Original TX-RX unit” and “ServiceTX-RX unit”
Supplied Accessories of “Service TX-RX unit”
“Service TX-RX unit” DataThe following data is written on the service unit:
After Changing the PCB(1) After changing the printed circuit board, write the up-to-
date Firmware following the instructions in the “2.2REALIGNMENT - 2.2.6 Firmware Programming Mode”.• Write the Firmware in accordance to the Market. If you
write different Market Firmware, there are timescommunication with the FPU is not possible.
(2) Using the KPG-D3/D3N, select your desired item (ModelName) from the Radio Configuration> ProductInformation menu, then use Read/ Write > WriteConfiguration to the Transceiver to write the FPU data(PC Programming mode). When writing to thetransceiver, a Warning Message, corresponding to theitem selected, appears. Click [OK] to continue writing thedata.
(3) Tools > Test/Tuning, then adjust the various adjustmentdata (PC Test Mode) as described in the “SECTION 4ADJUSTMENT”.
(4) Attach the new labels corresponding to the new printedcircuit board. (Refer to the images below for labelplacement.)
(5) If necessary, write the FPU data used by the customerwith the KPG-D3/D3N.
Model Name Original TX-RX unit Number
For Service TX-RX unit Number
NX-3720H(G)/3720H(K)
XC1-182K-00 XCA-033K-00
NX-3720(G)/3720(E)
XC1-182K-00 XCA-033E-01
NX-3820H(G)/3820H(K)
XC1-183K-00 XCA-034K-00
NX-3820H(G)/3820H(K2)
XC1-183K-01 XCA-034K-01
NX-3820(G)/3820(E)
XC1-183K-01 XCA-034E-01
Model Name Marking seal
NX-3720H(G)/3720H(K)
XCA-033K-00
NX-3720(G)/3720(E)
XCA-033E-01
NX-3820H(G)/3820H(K)
XCA-034K-00
NX-3820H(G)/3820H(K2)
XCA-034K-01
NX-3820(G)/3820(E)
XCA-034E-01
Item (Including Parts Number) Quantity
TX-RX Unit (XC1-182, XC1-183) 1
KENWOOD ESN/ NXDN ESN/ ProductNumber/ MPT ESN Label
1
The following marking seals are affixed on the shield cover
of the service TX-RX unit (XCA-033K-00/XCA-033E-01/
XCA-034K-00/XCA-034K-01/XCA-034E-01).
Data Type Desctiption
KENWOOD ESN NX-3720, NX-3720HModel name: [XCA-033]NX-3720S (K, E)Type:K, EThe same number as the KENWOODESN label is written.
NX-3820, NX-3820HModel name: [XCA-034]NX-3820S (K, K2, E)Type:K, K2, EThe same number as the KENWOOD ESN label is written.
NXDN ESN/ MPT ESN/Product number
The same number as the NXDN ESN/ MPT ESN/ Pruduct Number label is written.
1-166 (No.RA054<Rev.001>)
Note:• When using the ESN Validation function of NXDN
Trunking, the NXDN ESN number changes when thecircuit board is changed (the number is written on thecircuit board); the NXDN Trunking System cannot beaccessed.Use the KPG-110SM on the NXDN Trunking System sideto reprogram the NXDN ESN number.
• When a new printed circuit board is used, the KENWOODESN changes, as does the Transceiver Informationdisplay of the KPG-D3/D3N, but this does not have anyeffect on the operation of the transceiver.
• If changing to the original ESN, please contact our servicecenter.
• KPG-D3N can't be used for E type.
ESN Label Layout
• NX-3720H(G)[K], NX-3720(G)[E], NX-3720[E], NX-3820H(G)[K], NX-3820H[K], NX-3820H(G)[K2], NX-3820(G)[E], NX-3820[E]
• NX-3720H[K], NX-3820H[K2]
Cut a ESN Label at dotted line.
ESN Label
Note:
(No.RA054<Rev.001>)1-167
5.5 Operating Method of Enforced Firmware Overwriting Mode
Enforced firmware overwriting mode is a mode to forcibly overwrite the transceiver firmware when the operations as instructed inSection 2.2.2 "How to Enter Each Mode" does not allow the transceiver to enter the firmware programming mode, for instance, whenthe transceiver fails to start up due to the transceiver failure.
(1) Prepare the followings:• Transceiver (NX-3720, NX-3720H, NX-3820 or NX-3820H)• Regulated DC power supply• Programming interface cable (KPG-46U or KPG-46X)• Power cable
(2) Remove the cabinet, top packing and shielding plate of the transceiver. Connect a transceiver, regulated DC power supply, programming interface cable (KPG-46U or KPG-46X) and power cable.
(3) While FLDM terminal has a short-circuit with GND terminal on the PCB, turn its power ON.
Left: FLDM terminal
Right: GND terminal
1-168 (No.RA054<Rev.001>)
(4) Upon startup of FLDM loader, "FIRMWARE PROG" appears on an LCD screen.(5) Start KFL up, select the desired firmware you wish to overwrite, select the COM port number and baud rate, and then click the
"Write" button.
Note:Configuring "Auto" for baud rate automatically apply the maximal speed of baud rate allowed for a programming cableconnected to the selected COM port number.Upon start of overwriting on the transceiver, "LOADING" appears on an LCD screen.
(6) Upon completion of the firmware overwriting, "CHECKSUM xxxx" appears on an LCD screen.
(No.RA054<Rev.001>) 2-1 2-1 (No.RA054<Rev.001>)
PRECAUTIONS ON SCHEMATIC DIAGRAMS
* Due to the improvement in performance, some part numbers shown in the circuit diagrams
may not agree with those indicated in the Parts List.
* The parts numbers, values and rated voltage etc. in the Schematic Diagrams are for
reference only.
* Since the circuit diagrams are standard ones, the circuits and circuit constants may be
subject to change for improvement without any notice.
* The parts of the symbol with " * " may vary depending on model. Refer to the parts list for details.
* The parts of the symbol with " $ " are unmounted parts.
(No.RA054<Rev.001>) 2-2 2-2 (No.RA054<Rev.001>)
D
C
B
A
5 4 3 2 1
R681
R672
R671
R667
R666
R659
R6
58
R655
R654
R6
53
R652
R651
R650
R6
49
R648
R6
47
R646
R645
R644
R643
R634
R633 R631
R630
R628R627
R625
R623
R622
R6
18
R615
R613
R5
39
R534
R533
R532R531
R5
30
R529
R5
28
R527
R5
24 R523 R522
R5
20
R5
19
R5
16
R5
11 R505
R5
03
R502
R501
R4
99
R4
89
R486
R485
R4
83
R4
62
R444
R441
R440R439
R438
R4
18
R4
08
R4
07
R2
80
R2
79
R277 R276
R2
75
R2
74
R2
73
R2
71
R266
R265 R2
60R259
R251
R250
R2
48
R247
R245
R244
R2
43
R242
R241R
24
0
R239
R2
38
R235
R231
R230
R229
R213
R2
12
R2
11
R204
R203
R1
49
R1
48
R1
47
R1
46
R1
45
R1
44
R135
R1
34
R1
33
R1
32
R128
R127 R125
R124
R1
23
R1
22
R121
R120
R119
R1
18
R1
17
R1
15
R1
14
R1
13
R112
R109
R108
R84
R8
3
R8
2
R8
1
R7
7
R76R75
R7
4
R73R
72
R7
1
R70
R6
9
R6
8
R67 R66
R65
R6
4
R62
R5
7R
55
R5
4
R53
R5
2R5
1 R48
R42
R40
R39
R3
8
R36R
35
R29
R2
7
R2
Q6
06
Q605
Q604
Q404
Q4
03
Q402
Q2
06
Q205
Q204
Q202
Q1
07
Q1
04
Q1
03
Q2
5
Q2
3
Q22
Q21
Q2
0
Q1
9
Q13
Q1
2
Q1
1
L4
18
L4
17
L412
L4
11
L410
L4
09
L4
08
L4
07
L4
06
L405
L2
26
L2
25
L221
L220
L219
L2
18
L2
17
L2
08
L2
07
L1
24
L123L121
L119
L107
L19L
17
L16
L1
4
L1
1
IC14
E101
D6
19
D617
D6
15
D602
D410
D4
09
D407
D406 D405 D404D403 D402
D2
01
D107
D1
01
D2
0
D1
7
CP405CP404CP403
CN97
CN96 CN95
CN93
CN92
CN91
CN90
CN89
CN88
CN
87
CN
86
CN82
CN81
CN80
CN79
CN78
CN
77
CN
76
CN75
CN74
CN68
CN67
CN61
CN60
CN59
CN58
CN
57
CN55
CN49
CN48
CN33
CN32
CN31
CN30
CN29
CN28
CN27
CN26
CN25
CN24
CN23
CN22
CN21
CN20
CN
19
CN17
CN
16
CN15
CN14
CN13CN12 CN11
C6
61
C658
C6
57
C651
C634
C633
C632
C6
31
C630
C629
C6
28
C627
C6
26
C606C605
C528
C527
C5
26
C5
23
C522
C521
C5
20
C5
19 C514
C5
11
C509
C5
07
C5
06
C5
05
C5
03
C501
C498
C492
C4
91
C4
89
C488 C487
C486
C485
C4
84
C475
C474C473
C472
C471
C470
C469
C468
C467
C466
C465
C464
C463
C461
C460
C459
C458
C457
C456
C455
C4
53
C4
52
C451
C449
C448
C4
46
C444
C443
C442
C441
C440
C439
C437
C434
C431
C4
29
C428
C4
25
C424
C4
22
C421
C4
12
C4
11
C4
10
C2
80
C279
C2
72
C271
C2
70
C2
66
C2
63
C260
C249
C247
C2
45
C2
44
C2
43
C2
42
C2
41
C239
C237
C236
C2
35
C232
C2
14 C213
C2
12
C211
C148
C1
47
C1
46
C145
C1
43C142
C1
41C140
C1
39
C1
30
C125
C116
C1
15
C1
14
C112
C111
C110
C1
09
C108
C69
C68
C6
7
C66
C6
5
C64
C63
C62C61
C6
0
C59
C58
C57
C5
6
C5
5
C5
2
C51
C50
C4
9
C46
C44
C4
3
C4
1
C4
0
C3
9
C38
C37
C35
C33
C3
0
C2
9
C2
8
C26
C25
C22
C21
C2
0
C12
R5
L1
J2
C5
VoUT1
+B
XC1-182
F3
BA
TT
_C
HK
R2
CN1
IC407
RT
C
IC406
IC405
IC413
CN3
C4
F4
IC602
IC603RXD1
C2 C3
J1
IC12
IC24
IC20
IC16
IC608IC414 IC17
IC204
IC203
IC205
IC101
CN
2
C1
TX
D1
IC1
GN
D
FLDM
TXD0
IC601
J7C-0192-00
IC201
3
4
57
8
15
16
11
12
F2
R1
R3R4
10
13
14
F5
9
6
RXD0
IC26
IC21
IC23
F6
1
2
F1
D1
IC408
_DET
VBUS
--- Component side view (J7C-0192-00) ---
TX-RX UNIT (XC1-182K-00 (NX-3720H(G), NX-3720H, NX-3720(G), NX-3720))
PRINTED CIRCUIT BOARD
(No.RA054<Rev.001>) 2-3 2-3 (No.RA054<Rev.001>)
D
C
B
A
54321
TH401
TH
203
TH202
TH201
R680
R679
R678
R677
R676
R675
R674
R673
R670
R669
R668
R665
R664
R663
R662R661
R660
R657
R656
R642
R641
R640
R639 R638
R637
R636
R635
R632
R629
R626 R624
R621
R620 R619
R617R616
R614
R538
R537
R536
R535
R526
R525
R518
R517
R514
R513
R512
R509
R508
R507
R506
R504
R500
R498
R497
R496
R495
R494
R493 R492R491
R490
R488
R487R484
R482
R481
R480
R479
R478
R477
R476
R475
R474
R473
R472R471
R470
R469
R468
R467
R466R465
R464R463
R461
R460
R459
R458
R457
R456R455
R454
R453
R452
R451
R450
R449
R448
R447
R446
R445
R443
R442
R437
R436
R435
R434
R433
R432
R431
R429
R428
R427
R426
R425
R424
R423
R422
R421
R420
R416
R326
R325
R324
R323
R322
R321
R320
R319
R317
R316
R315
R314
R313
R312
R311
R310
R309
R308
R307
R305
R304
R303
R302
R282
R278
R272
R270
R269
R267
R262
R261
R256
R233
R228 R227
R226
R225
R224
R223
R222
R221
R220
R219
R218
R217
R216
R215
R214
R208
R207
R206
R205
R143
R142
R141
R140
R139
R138
R137
R136R131
R116
R80
R79
R78
R6
3
R61
R60
R59
R58
R56
R50
R49
R47
R46
R45
R44
R43
R41
R37
R34
R33
R32
R31
R30
R28
R26
R25
R24R23
R22
R21
Q603
Q602
Q601
Q401
Q301
Q201
Q106
Q105
Q18
Q17
Q1
6Q
15
Q14
L603
L602
L601
L420
L419 L416L415
L41
4
L413
L404
L403
L402
L401
L3
17
L315
L314
L313
L312
L311
L310
L309
L308
L307
L306
L305
L304
L303
L302
L224
L223
L222
L215
L214
L213
L212
L211
L210
L209
L118
L117
L116
L115
L113
L112
L111
L110
L109
L108
L18
L15
L13
L12
IC609
IC404
IC302
IC301
IC25
IC19
IC13
E11
D618
D616
D614
D613
D612
D611
D610 D609
D608
D607
D606D605
D604
D603
D601
D408
D401
D304
D303
D302
D301
D209
D208
D207
D206
D205
D204
D202
D108
D106
D105
D104
D103
D102
D27
D26
D24
D22
D21
D19
D18
D16
D15
D14
D13
CP
605
CP604
CP602 CP601
CP414 CP413CP412
CP
411
CP
410
CP409 CP408
CP
407
CP406
CP402
CP401
CP303 CP302 CP301
CN98
CN94
CN85
CN83
CN72
CN71
CN70
CN69
CN66
CN65
CN64
CN63
CN62
CN56
CN54
CN53
CN52
CN51
CN50
CN47
CN46
CN45
CN44
CN43
CN42
CN41CN40
CN39
CN38CN37
CN36
CN35
CN34
CN
18
C665
C664
C663
C660
C659
C656
C655
C653
C652
C650
C649
C648
C647
C646
C645
C644
C643
C642
C641
C640
C639
C638
C637
C636
C635
C625
C624
C623
C622
C621
C620
C619
C618
C617
C616
C615
C614
C613
C612
C611
C610
C609
C608
C607
C525
C524
C518
C517
C516
C515
C510
C504
C502
C49
7
C495
C4
94C493 C490 C483
C482
C481C480C479
C478C
477
C476
C462
C454
C450
C447
C445
C438
C436
C435
C433
C432
C430
C427
C426
C423C420
C419
C418
C41
7
C416
C415
C414
C405
C348
C347
C346
C345
C344
C343
C342
C341
C340
C339
C338
C337
C336
C335
C334
C333
C332
C331
C330
C329
C328
C327
C326
C325
C324
C323
C322
C321
C320
C319
C318
C317
C316
C315
C314
C313
C312
C311
C310
C309
C308
C307
C306
C305
C304
C278
C277
C275
C274
C268
C267
C265
C264
C262
C261
C259
C258
C257
C256
C255
C254
C253
C252
C251
C250
C238
C234
C233
C231
C230
C229
C228
C227
C226
C225
C224
C223
C222
C221
C220
C219
C218
C216
C209
C208
C207
C138
C137
C136
C135
C134
C133
C132
C131
C129
C128
C127
C124
C123
C120
C113
C76
C75
C74
C73
C72
C54
C53
C4
8
C47
C45
C42 C36
C34
C32
C31
C27
C24
C19
C18
C17
C16
C15
C14
C11
L4
L3
L2
L6
IC412
L5
IC411
IC410IC401
IC403
IC409
IC202
IC402
IC604
IC606
L7
IC15
IC605IC
18
IC22
IC607
X401
X402
TX-RX UNIT (XC1-182K-00 (NX-3720H(G), NX-3720H, NX-3720(G), NX-3720))
--- Foil side view (J7C-0192-00) ---
(No.RA054<Rev.001>) 2-4 2-4 (No.RA054<Rev.001>)
A-1C
Side Y axisX axis
ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one
interval.
REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION
IC IC1 B- 4CIC12 B- 3AIC13 A- 5AIC14 B- 2AIC15 A- 5AIC16 B- 3BIC17 B- 3BIC18 A- 5AIC19 A- 1AIC20 B- 3BIC21 B- 3AIC22 A- 4AIC23 B- 2AIC24 B- 3BIC25 A- 5CIC26 B- 3BIC101 B- 2BIC202 A- 2CIC203 B- 2BIC205 B- 2BIC301 A- 1AIC302 A- 1AIC401 A- 3BIC402 A- 4AIC403 A- 3BIC404 A- 4AIC405 B- 4AIC406 B- 4AIC407 B- 3AIC408 B- 3AIC409 A- 3BIC410 A- 3BIC411 A- 3AIC412 A- 2AIC413 B- 4AIC414 B- 3BIC602 B- 5BIC603 B- 4BIC604 A- 5BIC605 A- 5CIC606 A- 4DIC607 A- 4BIC608 B- 4BIC609 A- 4D TRANSISTORQ11 B- 4BQ12 B- 5BQ13 B- 4BQ14 A- 5AQ15 A- 5AQ16 A- 5AQ17 A- 4CQ18 A- 4CQ19 B- 3BQ20 B- 3BQ21 B- 2BQ22 B- 1BQ23 B- 3CQ25 B- 4BQ103 B- 2BQ104 B- 2AQ105 A- 2AQ106 A- 2AQ107 B- 1AQ201 A- 3CQ202 B- 3B
Q204 B- 2BQ205 B- 2BQ206 B- 3BQ301 A- 1AQ401 A- 4BQ402 B- 4AQ403 B- 3AQ404 B- 4AQ601 A- 4BQ602 A- 4DQ603 A- 4DQ604 B- 5AQ605 B- 5BQ606 B- 4A DIODE D1 B- 5CD13 A- 5AD14 A- 3BD15 A- 4CD16 A- 5CD17 B- 2AD18 A- 5AD19 A- 5AD20 B- 4BD21 A- 5AD22 A- 5AD24 A- 5AD26 A- 5AD27 A- 5AD101 B- 2BD102 A- 2AD103 A- 2BD104 A- 2BD105 A- 2BD106 A- 2BD107 B- 2AD108 A- 2AD201 B- 3BD202 A- 2BD204 A- 1CD205 A- 1CD206 A- 1CD207 A- 1BD208 A- 1BD209 A- 1BD301 A- 1AD302 A- 1AD303 A- 1BD304 A- 1BD401 A- 3BD402 B- 4AD403 B- 4AD404 B- 3AD405 B- 3AD406 B- 3AD407 B- 4AD408 A- 4AD409 B- 4AD410 B- 3AD601 A- 4DD602 B- 4BD603 A- 4CD604 A- 4CD605 A- 4DD606 A- 4DD607 A- 4CD608 A- 4C
D609 A- 4DD610 A- 4DD611 A- 4DD612 A- 4BD613 A- 4BD614 A- 4CD615 B- 5BD616 A- 4DD617 B- 4DD618 A- 4DD619 B- 4A RESISTOR R2 B- 4BR5 A- 1DR21 A- 5AR22 A- 5AR23 A- 5AR24 A- 5AR25 A- 5AR26 A- 5AR27 B- 4BR28 A- 5AR29 B- 4BR30 A- 5AR31 A- 5AR32 A- 5AR33 A- 4AR34 A- 4AR35 B- 3BR36 B- 3BR37 A- 3BR38 B- 3BR39 B- 3BR40 B- 3BR41 A- 5CR42 B- 2AR43 A- 5CR44 A- 4CR45 A- 5CR46 A- 5CR47 A- 4CR48 B- 3BR49 A- 4CR50 A- 4CR51 B- 3BR52 B- 3BR53 B- 3AR54 B- 3BR55 B- 3AR56 A- 5CR57 B- 3AR58 A- 5CR59 A- 5CR60 A- 5CR61 A- 5CR62 B- 4BR63 A- 5CR64 B- 3AR65 B- 3BR66 B- 2AR67 B- 2AR68 B- 2AR69 B- 4CR70 B- 4CR71 B- 3BR72 B- 3CR73 B- 1B
R74 B- 1BR75 B- 4AR76 B- 4AR77 B- 4BR78 A- 5BR79 A- 5BR80 A- 5AR81 B- 4BR82 B- 4BR83 B- 3CR84 B- 3CR108 B- 1AR109 B- 1AR112 B- 2BR113 B- 1BR114 B- 2BR115 B- 2BR116 A- 1AR117 B- 2BR118 B- 1AR119 B- 1BR120 B- 1AR121 B- 2BR122 B- 2BR123 B- 1AR124 B- 1AR125 B- 2BR127 B- 2BR128 B- 2BR131 A- 2AR132 B- 2AR133 B- 2AR134 B- 2AR135 B- 2AR136 A- 2AR137 A- 2AR138 A- 2AR139 A- 2AR140 A- 2AR141 A- 2AR142 A- 2AR143 A- 2AR144 B- 1AR145 B- 1AR146 B- 2AR147 B- 2AR148 B- 1AR149 B- 1AR203 B- 2BR204 B- 3BR205 A- 2CR206 A- 2CR207 A- 1BR208 A- 1BR211 B- 3BR212 B- 3BR213 B- 2BR214 A- 2BR215 A- 2BR216 A- 2BR217 A- 2CR218 A- 2CR219 A- 2CR220 A- 2CR221 A- 2CR222 A- 2BR223 A- 2BR224 A- 2B
R225 A- 2BR226 A- 3BR227 A- 3BR228 A- 3BR229 B- 2BR230 B- 2BR231 B- 3BR233 A- 3BR235 B- 3BR238 B- 3BR239 B- 3CR240 B- 3CR241 B- 2BR242 B- 3CR243 B- 3CR244 B- 2BR245 B- 2BR247 B- 2BR248 B- 2BR250 B- 2BR251 B- 2BR256 A- 2BR259 B- 2BR260 B- 2BR261 A- 2BR262 A- 2CR265 B- 2BR266 B- 2BR267 A- 2BR269 A- 1BR270 A- 1CR271 B- 2BR272 A- 1CR273 B- 2BR274 B- 2BR275 B- 2BR276 B- 1BR277 B- 1BR278 A- 2CR279 B- 2BR280 B- 3BR282 A- 2BR302 A- 1AR303 A- 1AR304 A- 1AR305 A- 1BR307 A- 1AR308 A- 1BR309 A- 1AR310 A- 1AR311 A- 1AR312 A- 1AR313 A- 1BR314 A- 1BR315 A- 1BR316 A- 1AR317 A- 1AR319 A- 1AR320 A- 1AR321 A- 1AR322 A- 1AR323 A- 1AR324 A- 1AR325 A- 1AR326 A- 1AR407 B- 3AR408 B- 3AR416 A- 3A
R418 B- 5AR420 A- 4BR421 A- 4BR422 A- 4BR423 A- 4BR424 A- 4BR425 A- 4BR426 A- 4BR427 A- 4BR428 A- 4BR429 A- 4BR431 A- 3BR432 A- 3BR433 A- 3BR434 A- 4BR435 A- 4AR436 A- 3BR437 A- 3BR438 B- 4AR439 B- 4AR440 B- 4AR441 B- 4AR442 A- 4BR443 A- 4BR444 B- 4BR445 A- 4AR446 A- 4AR447 A- 4BR448 A- 4BR449 A- 4AR450 A- 4BR451 A- 4AR452 A- 4AR453 A- 4AR454 A- 4AR455 A- 4AR456 A- 4AR457 A- 4AR458 A- 4AR459 A- 4AR460 A- 4AR461 A- 4AR462 B- 3BR463 A- 4AR464 A- 4AR465 A- 4AR466 A- 4AR467 A- 4AR468 A- 4AR469 A- 4AR470 A- 4AR471 A- 4AR472 A- 4AR473 A- 4BR474 A- 4BR475 A- 4BR476 A- 4BR477 A- 4BR478 A- 4AR479 A- 4BR480 A- 4AR481 A- 4BR482 A- 4AR483 B- 4AR484 A- 4BR485 B- 4AR486 B- 4AR487 A- 4B
R488 A- 3BR489 B- 5AR490 A- 4AR491 A- 4AR492 A- 4AR493 A- 4AR494 A- 2BR495 A- 2BR496 A- 2BR497 A- 2BR498 A- 3BR499 B- 3AR500 A- 3BR501 B- 4AR502 B- 4AR503 B- 3AR504 A- 3BR505 B- 3AR506 A- 3AR507 A- 3AR508 A- 3AR509 A- 2AR511 B- 3AR512 A- 3BR513 A- 3BR514 A- 3BR516 B- 3AR517 A- 3BR518 A- 3AR519 B- 3AR520 B- 3AR522 B- 4AR523 B- 4AR524 B- 4AR525 A- 3BR526 A- 3AR527 B- 4AR528 B- 4BR529 B- 3BR530 B- 3BR531 B- 3BR532 B- 4BR533 B- 3BR534 B- 3BR535 A- 3BR536 A- 4BR537 A- 4BR538 A- 3BR539 B- 3AR613 B- 4DR614 A- 4DR615 B- 5BR616 A- 4DR617 A- 4DR618 B- 4BR619 A- 5BR620 A- 4BR621 A- 4BR622 B- 5BR623 B- 4CR624 A- 4DR625 B- 4DR626 A- 4DR627 B- 4DR628 B- 4DR629 A- 4DR630 B- 4CR631 B- 4C
R632 A- 4DR633 B- 4CR634 B- 4DR635 A- 4DR636 A- 4DR637 A- 4DR638 A- 4DR639 A- 4DR640 A- 4DR641 A- 4DR642 A- 4DR643 B- 5DR644 B- 5BR645 B- 5AR646 B- 5BR647 B- 5BR648 B- 5AR649 B- 5BR650 B- 4DR651 B- 5DR652 B- 5BR653 B- 5BR654 B- 5AR655 B- 5BR656 A- 4DR657 A- 4DR658 B- 4BR659 B- 4DR660 A- 4BR661 A- 4BR662 A- 4BR663 A- 4BR664 A- 4BR665 A- 4BR666 B- 4BR667 B- 4BR668 A- 4BR669 A- 4BR670 A- 5BR671 B- 4BR672 B- 4BR673 A- 4BR674 A- 4BR675 A- 4BR676 A- 4BR677 A- 4BR678 A- 5BR679 A- 5BR680 A- 5BR681 B- 4A CAPACITORC1 B- 5DC2 B- 5DC3 B- 5DC4 B- 5AC5 B- 3CC11 A- 5AC12 B- 4AC14 A- 5AC15 A- 5AC16 A- 5AC17 A- 5AC18 A- 5AC19 A- 5AC20 B- 4BC21 B- 5BC22 B- 4C
C24 A- 5AC25 B- 4BC26 B- 4CC27 A- 5AC28 B- 5BC29 B- 4AC30 B- 5CC31 A- 5AC32 A- 5CC33 B- 3BC34 A- 5CC35 B- 3BC36 A- 4CC37 B- 3BC38 B- 3BC39 B- 2AC40 B- 3B
C41 B- 2AC42 A- 4CC43 B- 3BC44 B- 3BC45 A- 5CC46 B- 2AC47 A- 4CC48 A- 5CC49 B- 3AC50 B- 3BC51 B- 3BC52 B- 3AC53 A- 5CC54 A- 5CC55 B- 3BC56 B- 4BC57 B- 3BC58 B- 3AC59 B- 3AC60 B- 2AC61 B- 2AC62 B- 2AC63 B- 2AC64 B- 4CC65 B- 4CC66 B- 4CC67 B- 1BC68 B- 3CC69 B- 3BC72 A- 1AC73 A- 1AC74 A- 5AC75 A- 5AC76 A- 5AC108 B- 2BC109 B- 2BC110 B- 2BC111 B- 2BC112 B- 2BC113 A- 1AC114 B- 1AC115 B- 2AC116 B- 2BC120 A- 2AC123 A- 2BC124 A- 2BC125 B- 2AC127 A- 2BC128 A- 2BC129 A- 2AC130 B- 2A
C131 A- 2AC132 A- 2AC133 A- 2AC134 A- 2AC135 A- 2AC136 A- 2AC137 A- 2AC138 A- 2AC139 B- 1AC140 B- 1AC141 B- 1AC142 B- 1AC143 B- 1AC145 B- 1AC146 B- 1AC147 B- 1AC148 B- 1AC207 A- 1CC208 A- 1CC209 A- 1DC211 B- 3BC212 B- 3BC213 B- 2BC214 B- 2BC216 A- 2BC218 A- 2CC219 A- 2CC220 A- 2CC221 A- 2CC222 A- 2CC223 A- 2CC224 A- 2CC225 A- 2CC226 A- 2BC227 A- 2BC228 A- 2CC229 A- 3CC230 A- 3CC231 A- 3BC232 B- 3CC233 A- 3CC234 A- 3BC235 B- 2BC236 B- 2BC237 B- 1BC238 A- 3CC239 B- 2BC241 B- 3CC242 B- 2CC243 B- 2CC244 B- 2CC245 B- 2CC247 B- 2CC249 B- 2CC250 A- 2CC251 A- 2BC252 A- 2BC253 A- 2CC254 A- 1CC255 A- 1CC256 A- 1BC257 A- 1BC258 A- 1CC259 A- 1CC260 B- 2CC261 A- 1BC262 A- 1CC263 B- 2B
C264 A- 1CC265 A- 1CC266 B- 1DC267 A- 1DC268 A- 1DC270 B- 2BC271 B- 2BC272 B- 2BC274 A- 2BC275 A- 2BC277 A- 1CC278 A- 1DC279 B- 1CC280 B- 1DC304 A- 1AC305 A- 1AC306 A- 1AC307 A- 1BC308 A- 1BC309 A- 1BC310 A- 1AC311 A- 1BC312 A- 1AC313 A- 1AC314 A- 1AC315 A- 1AC316 A- 1AC317 A- 1AC318 A- 1BC319 A- 1BC320 A- 1BC321 A- 1AC322 A- 1AC323 A- 1AC324 A- 1AC325 A- 1AC326 A- 1AC327 A- 1AC328 A- 1AC329 A- 1AC330 A- 1AC331 A- 1AC332 A- 1AC333 A- 1BC334 A- 1BC335 A- 1AC336 A- 1AC337 A- 1BC338 A- 1AC339 A- 1AC340 A- 1AC341 A- 1AC342 A- 1AC343 A- 1AC344 A- 1AC345 A- 1AC346 A- 1AC347 A- 1AC348 A- 1AC405 A- 2AC410 B- 5AC411 B- 5AC412 B- 5AC414 A- 3AC415 A- 3AC416 A- 3AC417 A- 5BC418 A- 4B
C419 A- 4AC420 A- 4BC421 B- 4AC422 B- 4AC423 A- 5BC424 B- 4AC425 B- 4AC426 A- 5BC427 A- 5AC428 B- 4AC429 B- 4AC430 A- 5AC431 B- 4AC432 A- 5AC433 A- 4BC434 B- 4BC435 A- 5BC436 A- 4BC437 B- 4BC438 A- 4BC439 B- 4AC440 B- 4BC441 B- 4AC442 B- 4BC443 B- 4AC444 B- 4AC445 A- 4BC446 B- 4BC447 A- 4BC448 B- 4BC449 B- 4AC450 A- 4BC451 B- 4BC452 B- 4BC453 B- 4BC454 A- 4BC455 B- 4AC456 B- 4BC457 B- 4AC458 B- 4AC459 B- 4BC460 B- 4AC461 B- 4BC462 A- 4BC463 B- 4AC464 B- 4BC465 B- 4AC466 B- 4BC467 B- 4AC468 B- 4BC469 B- 4AC470 B- 4AC471 B- 4AC472 B- 4BC473 B- 4BC474 B- 4BC475 B- 4BC476 A- 3AC477 A- 3BC478 A- 3BC479 A- 3BC480 A- 3BC481 A- 4BC482 A- 4BC483 A- 4BC484 B- 4AC485 B- 4AC486 B- 4A
C487 B- 4AC488 B- 4AC489 B- 4AC490 A- 4BC491 B- 3AC492 B- 4AC493 A- 3BC494 A- 3BC495 A- 3BC497 A- 2BC498 B- 3AC501 B- 4AC502 A- 3BC503 B- 3AC504 A- 3BC505 B- 3AC506 B- 3AC507 B- 3AC509 B- 3AC510 A- 3BC511 B- 4AC514 B- 3AC515 A- 3AC516 A- 3AC517 A- 2AC518 A- 2AC519 B- 4AC520 B- 4AC521 B- 4AC522 B- 4AC523 B- 4AC524 A- 3BC525 A- 3BC526 B- 3BC527 B- 3BC528 B- 3BC605 B- 5BC606 B- 4BC607 A- 5BC608 A- 4CC609 A- 5DC610 A- 5CC611 A- 5CC612 A- 5CC613 A- 4DC614 A- 4DC615 A- 4DC616 A- 4DC617 A- 4DC618 A- 4DC619 A- 4DC620 A- 4DC621 A- 4DC622 A- 4DC623 A- 4DC624 A- 4DC625 A- 4DC626 B- 5BC627 B- 5AC628 B- 5BC629 B- 5BC630 B- 5DC631 B- 5BC632 B- 5BC633 B- 5AC634 B- 5BC635 A- 4DC636 A- 4B
C637 A- 4DC638 A- 4BC639 A- 4BC640 A- 4BC641 A- 4BC642 A- 4BC643 A- 4BC644 A- 4BC645 A- 4BC646 A- 4BC647 A- 4BC648 A- 4BC649 A- 4BC650 A- 4BC651 B- 4BC652 A- 4BC653 A- 4BC655 A- 4BC656 A- 4BC657 B- 4BC658 B- 4BC659 A- 4BC660 A- 4DC661 B- 4BC663 A- 4CC664 A- 4DC665 A- 4D OTHER X401 A- 4BX402 A- 3B TH201 A- 1BTH202 A- 1DTH203 A- 2BTH401 A- 4B CN1 B- 3ACN2 B- 5ACN3 B- 5ACN11 B- 4ACN12 B- 4ACN13 B- 4ACN14 B- 5ACN15 B- 5ACN16 B- 5ACN17 B- 4ACN18 A- 5BCN19 B- 5CCN20 B- 4DCN21 B- 4ACN22 B- 2BCN23 B- 2BCN24 B- 2ACN25 B- 1BCN26 B- 2CCN27 B- 2CCN28 B- 3BCN29 B- 3BCN30 B- 2BCN31 B- 2BCN32 B- 2BCN33 B- 1ACN34 A- 1ACN35 A- 1ACN36 A- 1ACN37 A- 1ACN38 A- 1A
CN39 A- 1ACN40 A- 1ACN41 A- 1ACN42 A- 1ACN43 A- 1ACN44 A- 1ACN45 A- 1ACN46 A- 1ACN47 A- 1ACN48 B- 1ACN49 B- 1ACN50 A- 2ACN51 A- 3BCN52 A- 3ACN53 A- 3BCN54 A- 3ACN55 B- 3BCN56 A- 4BCN57 B- 4ACN58 B- 4ACN59 B- 4ACN60 B- 4ACN61 B- 4BCN62 A- 4BCN63 A- 4BCN64 A- 4ACN65 A- 4ACN66 A- 4ACN67 B- 3BCN68 B- 3BCN69 A- 4ACN70 A- 4BCN71 A- 3ACN72 A- 3BCN74 B- 4ACN75 B- 4ACN76 B- 3ACN77 B- 3ACN78 B- 3ACN79 B- 2ACN80 B- 3ACN81 B- 3BCN82 B- 3BCN83 A- 3ACN85 A- 3ACN86 B- 4ACN87 B- 4BCN88 B- 4DCN89 B- 3BCN90 B- 5BCN91 B- 4BCN92 B- 2BCN93 B- 3CCN94 A- 4ACN95 B- 4DCN96 B- 4DCN97 B- 4DCN98 A- 4B CP301 A- 1ACP302 A- 1ACP303 A- 1ACP401 A- 3BCP402 A- 4ACP403 B- 5ACP404 B- 5ACP405 B- 4ACP406 A- 3B
CP407 A- 3BCP408 A- 3ACP409 A- 3ACP410 A- 3ACP411 A- 2ACP412 A- 3ACP413 A- 3ACP414 A- 3ACP601 A- 5BCP602 A- 5BCP604 A- 4BCP605 A- 4B E11 A- 5CE101 B- 1A F1 B- 5CF2 B- 5BF3 B- 4DF4 B- 4BF5 B- 4CF6 B- 4D J1 A- 4DJ2 A- 5D L1 A- 1DL2 A- 1DL3 A- 1DL4 A- 1CL5 A- 1BL6 A- 1BL7 A- 2AL11 B- 3AL12 A- 5CL13 A- 5CL14 B- 2BL15 A- 5CL16 B- 3BL17 B- 3BL18 A- 1AL19 B- 3BL107 B- 2AL108 A- 2AL109 A- 2BL110 A- 2BL111 A- 2BL112 A- 2BL113 A- 2BL115 A- 2AL116 A- 2AL117 A- 2AL118 A- 2AL119 B- 2AL121 B- 1AL123 B- 1AL124 B- 1AL207 B- 3BL208 B- 2BL209 A- 2CL210 A- 2CL211 A- 2BL212 A- 2BL213 A- 3CL214 A- 3BL215 A- 3CL217 B- 1BL218 B- 3C
L219 B- 2CL220 B- 2CL221 B- 2CL222 A- 2BL223 A- 1CL224 A- 1CL225 B- 2BL226 B- 1DL302 A- 1BL303 A- 1BL304 A- 1AL305 A- 1AL306 A- 1AL307 A- 1AL308 A- 1BL309 A- 1BL310 A- 1BL311 A- 1BL312 A- 1AL313 A- 1AL314 A- 1AL315 A- 1BL317 A- 1BL401 A- 3AL402 A- 4BL403 A- 5BL404 A- 4B
L405 B- 4AL406 B- 4BL407 B- 4BL408 B- 4BL409 B- 4BL410 B- 4BL411 B- 4BL412 B- 4BL413 A- 3BL414 A- 3BL415 A- 3AL416 A- 3AL417 B- 4AL418 B- 4AL419 A- 3AL420 A- 4BL601 A- 4BL602 A- 4BL603 A- 4D
(No.RA054<Rev.001>) 2-5 2-5 (No.RA054<Rev.001>)
D
C
B
A
5 4 3 2 1
R681
R672
R671
R667
R666
R659
R6
58
R655
R654
R6
53
R652
R651
R650
R6
49
R648
R6
47
R646
R645
R644
R643
R634
R633 R631
R630
R628R627
R625
R623
R622
R6
18
R615
R613
R539
R534
R533
R532R531
R5
30
R529
R5
28
R527
R524 R523 R522
R520
R519
R516
R5
11 R505
R5
03
R502
R501
R4
99
R489
R486
R485
R4
83
R4
62
R444
R441
R440R439
R438
R418
R40
8
R40
7
R2
80
R277 R276
R2
75
R2
74
R2
73
R2
71
R266
R265
R2
61
R2
60R259
R2
58
R251
R250
R2
48
R247
R245
R244
R2
43
R242
R241
R2
40
R239
R2
38
R235
R231
R230
R229
R213
R2
12
R2
11
R204
R203
R147
R1
46
R145
R135
R1
34
R1
33
R1
32
R1
30
R1
29
R128
R127
R1
26
R125
R124
R1
23
R1
22
R121
R120
R119
R1
18
R1
17
R1
15
R1
14
R1
13
R112
R111
R1
10
R109
R1
08
R1
06
R1
05
R1
04
R1
03
R84
R8
3
R8
2
R8
1
R7
7
R76R75
R7
4
R73
R7
2R
71
R70
R6
9
R6
8
R67 R66
R65
R6
4
R62
R5
7R
55
R5
4
R53
R5
2R5
1 R48
R42
R40
R39
R3
8
R36
R3
5
R29
R2
7
R4
R3
R2
Q6
06
Q605
Q604
Q404
Q403
Q402
Q2
06
Q205
Q204
Q202
Q1
04
Q1
03
Q1
02
Q1
01
Q2
5
Q2
3
Q22
Q21
Q2
0
Q1
9
Q13
Q1
2
Q1
1
L418
L417
L412
L4
11
L410
L4
09
L4
08
L4
07
L4
06
L405
L2
26
L2
25
L221
L220
L219
L2
18
L2
17
L2
08
L2
07
L124
L1
23
L122
L1
21
L120
L119
L107
L1
06
L105
L104
L1
03
L1
02
L1
01
L19
L1
7
L16
L1
4
L1
1
IC14
E101
D6
19
D617
D6
15
D602
D410
D409
D407
D406 D405 D404D403 D402
D2
02D2
01
D107
D1
01
D2
0
D1
7
CP405CP404CP403
CN97CN96 CN95
CN93
CN92
CN91CN90
CN89
CN88
CN
87
CN86
CN82
CN81
CN80
CN79
CN78
CN77
CN76
CN75
CN74
CN68
CN67
CN61
CN60
CN59
CN58
CN
57
CN55
CN49
CN48
CN33
CN32
CN31
CN30
CN29
CN28
CN27
CN26
CN25
CN24
CN23
CN22
CN21
CN20
CN
19
CN17
CN
16
CN15
CN14
CN13CN12 CN11
C6
61
C658
C6
57
C651
C634
C633
C632
C6
31
C630
C629
C6
28
C627
C6
26
C606C605
C528
C527
C5
26
C523
C522
C521
C520
C519 C514
C511
C509
C507
C506
C505
C503
C501
C498
C492
C4
91
C489
C488 C487
C486
C485
C484
C475
C474C473
C472
C471
C470
C469
C468
C467
C466
C465
C464
C463
C461
C460
C459
C458
C457
C456
C455
C4
53
C4
52
C451
C449
C448
C4
46
C444
C443
C442
C441
C440
C439
C437
C434
C431
C4
29
C428
C4
25
C424
C4
22
C421
C412
C411
C410
C2
72
C271
C2
70
C266
C2
63
C260
C2
52
C2
51
C249
C247
C2
45
C2
44
C2
43
C2
42
C2
41
C239
C237
C236
C2
35
C232
C2
14 C213
C2
12
C211
C148
C1
47
C1
46
C145
C144
C143
C1
42
C141
C1
40
C139
C1
30
C1
26
C125
C122
C1
21
C119C
11
7
C116
C1
15
C1
14
C112
C111
C110
C1
09
C108
C105
C1
04
C1
03
C1
02
C69
C68
C6
7
C66
C6
5
C64
C63
C62C61
C6
0
C59
C58
C57
C5
6
C5
5
C5
2
C51
C50
C4
9
C46
C44
C4
3
C4
1
C4
0
C3
9
C38
C37
C35
C33
C3
0
C2
9
C2
8C26
C25
C22
C21
C2
0
C12
R5
L1
J2
C5
VoUT1
+B
XC1-183
BA
TT
_C
HK
R2
CN1
IC407
IC408
RT
C
IC406
IC405
IC413
CN3
C4
F4
IC602
IC603RXD1
C2 C3
J1
IC12
IC24
IC20
IC608IC414
IC17
IC204
IC203
IC205
IC101
CN
2
C1
D1
_DETVBUS
TX
D1
IC1
GN
D
F1
FLDM
TXD0
IC601
J7C-0193-00
IC201
1
3
4
57
8
15
16
11
12
F2
R1
R3R4
10
13
14
F5
9
6
RXD0
IC26
IC21IC23
2
F3
F6
IC16
TX-RX UNIT (XC1-183K-00 (NX-3820H(G), NX-3820H, NX-3820(G), NX-3820))
--- Component side view (J7C-0193-00) ---
(No.RA054<Rev.001>) 2-6 2-6 (No.RA054<Rev.001>)
D
C
B
A
54321
TH401
TH
20
3
TH202
TH201
R680
R679
R678
R677
R676
R6
75
R6
74
R673
R670
R6
69
R668
R6
65
R6
64
R663
R662R661
R660
R6
57
R6
56
R642
R6
41
R6
40
R6
39 R6
38
R6
37
R6
36
R6
35
R6
32
R629
R6
26 R6
24
R621
R620 R619
R617R616
R6
14
R5
38
R5
37
R5
36
R535
R526
R5
25
R518
R5
17
R5
14
R513
R512
R5
09
R5
08
R5
07
R5
06
R5
04
R5
00
R498
R497
R496
R495
R494
R493 R492R491
R490
R4
88
R487R484
R482
R481
R480
R479
R478
R477
R476
R475
R474
R473
R472R471
R470
R469
R468
R467
R466R465
R464R463
R461
R460R459
R458
R457
R456R455
R454
R453
R452
R451
R450
R449
R448
R447
R446
R445
R443
R442
R437
R4
36
R4
35
R4
34
R433
R432
R431
R429
R4
28
R427
R426
R425
R424
R423
R422
R421
R420
R4
16
R326
R325
R3
24
R3
23
R3
22
R321
R3
20
R319
R3
18
R3
17
R316
R3
15
R314
R3
13
R3
12
R3
11
R310
R3
09
R308
R307
R305
R304
R303
R302
R2
82
R2
81
R278
R272
R2
70
R2
69
R268
R2
67
R262
R2
56
R2
33
R228 R227
R2
26
R2
25
R224
R223
R222
R2
21
R2
20
R219
R218
R217
R2
16
R2
15
R214
R1
43
R1
42
R1
41
R1
40
R139
R138
R1
37
R136R131
R1
16
R80
R7
9
R7
8
R6
3
R6
1
R6
0
R5
9
R5
8
R56
R5
0
R4
9
R47
R46
R45
R44
R43
R41
R3
7
R34
R3
3
R3
2
R3
1
R30
R28
R2
6
R2
5
R2
4R23
R22
R21
Q6
03
Q602
Q6
01
Q4
01
Q301
Q201
Q1
06
Q1
05
Q18
Q17
Q1
6Q
15
Q14
L6
03
L602
L6
01
L420
L419 L416L415
L4
14
L413
L404
L4
03
L402
L4
01
L314
L313
L312
L311
L3
10
L309
L3
08
L3
07
L306
L3
05
L3
04
L303
L3
02
L227
L224
L2
23
L2
22
L2
16
L215
L2
14
L2
13
L212
L2
11
L210L209
L1
18
L1
17
L116
L115
L1
13
L1
12
L111
L110
L109
L1
08
L1
8
L15
L13
L1
2
IC609
IC404
IC302
IC301
IC2
5
IC19
IC1
3
E1
1
D618
D616
D614
D613
D612
D6
11
D610
D6
09
D608
D6
07
D606D605
D604
D6
03
D6
01
D408
D401
D304
D303
D3
02
D3
01
D209
D208
D207
D206
D205
D204
D108
D1
06
D1
05
D1
04
D1
03
D102
D2
7
D26
D24
D22
D2
1
D19
D1
8
D16
D1
5
D1
4
D1
3
CP
60
5
CP604
CP602 CP601
CP414 CP413CP412
CP
41
1
CP
41
0
CP409 CP408
CP
40
7
CP406
CP402
CP401
CP303 CP302 CP301
CN98
CN94
CN85
CN83
CN72
CN71
CN70
CN69
CN66
CN65
CN64
CN63
CN62
CN56
CN54
CN53
CN52
CN51
CN50
CN47
CN46
CN45
CN44
CN43
CN42
CN41CN40
CN39
CN38CN37
CN36
CN35
CN34
CN
18
C6
65
C664
C663
C6
60
C6
59
C6
56
C655
C6
53
C6
52
C650
C649
C6
48
C6
47
C6
46
C6
45
C644
C643
C642
C641
C6
40
C6
39
C638
C6
37
C6
36
C635
C6
25
C6
24
C6
23
C6
22
C6
21
C6
20
C6
19
C6
18
C6
17
C6
16
C6
15
C6
14
C613
C612
C6
11
C6
10
C6
09
C6
08
C607
C525
C524
C5
18
C5
17
C516
C5
15
C510
C5
04
C5
02
C4
97
C4
95
C4
94C4
93 C490 C483
C482
C481C480C4
79
C478
C4
77
C4
76
C462
C454
C4
50
C447
C4
45
C438
C436
C435
C433
C4
32
C4
30
C4
27
C4
26
C4
23C4
20
C4
19
C418
C4
17
C416
C415
C414
C405
C3
47
C346
C345
C344
C343
C342
C341
C3
40
C3
39
C3
38
C3
37
C3
36
C3
35
C3
34
C333
C332
C3
31
C330
C329
C328
C327
C326
C325
C3
24
C3
23
C322
C321
C3
20
C3
19
C317
C316
C315
C314
C313
C312
C311
C3
10
C3
09
C3
08
C307
C3
06
C3
05
C3
04
C2
74
C268
C267
C265
C264
C2
62
C261
C259
C258
C257
C256
C255
C254
C2
53
C2
50
C2
38
C234C233
C231
C2
30C
22
9
C228
C227
C2
26
C225
C2
24
C223
C2
22
C2
21
C2
20C
21
9
C218C217
C216
C207
C201
C1
38
C1
37
C1
36
C135
C1
34
C133
C1
32
C131
C129
C1
28
C127
C124
C1
23
C120
C1
13
C101
C7
6
C7
5
C74
C7
3
C7
2
C5
4
C5
3
C4
8
C4
7
C45
C42 C36
C3
4
C3
2
C31
C2
7
C2
4
C1
9
C18
C1
7
C1
6
C15
C14
C11
L4
L3
L2
L6
IC412
L5
IC411
IC410 IC401
IC403
IC409
IC202
IC22
IC4
02
IC607IC604
X4
02
IC606
X4
01
L7
IC1
5
IC605
IC1
8
TX-RX UNIT (XC1-183K-00 (NX-3820H(G), NX-3820H, NX-3820(G), NX-3820))
--- Foil side view (J7C-0193-00) ---
(No.RA054<Rev.001>) 2-7 2-7 (No.RA054<Rev.001>)
A-1C
Side Y axisX axis
ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one
interval.
REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION
IC IC1 B- 4CIC12 B- 3AIC13 A- 5AIC14 B- 2AIC15 A- 5AIC16 B- 3BIC17 B- 3BIC18 A- 5AIC19 A- 1AIC20 B- 3BIC21 B- 3AIC22 A- 4AIC23 B- 2AIC24 B- 3BIC25 A- 5CIC26 B- 3BIC101 B- 2BIC202 A- 2CIC203 B- 2BIC205 B- 2BIC301 A- 1AIC302 A- 1AIC401 A- 3BIC402 A- 4AIC403 A- 3BIC404 A- 4AIC405 B- 4AIC406 B- 4AIC407 B- 3AIC408 B- 3AIC409 A- 3BIC410 A- 3BIC411 A- 3AIC412 A- 2AIC413 B- 4AIC414 B- 3BIC602 B- 5BIC603 B- 4BIC604 A- 5BIC605 A- 5CIC606 A- 4DIC607 A- 4BIC608 B- 4BIC609 A- 4D TRANSISTORQ11 B- 4BQ12 B- 5BQ13 B- 4BQ14 A- 5AQ15 A- 5AQ16 A- 5AQ17 A- 4CQ18 A- 4CQ19 B- 3BQ20 B- 3BQ21 B- 2BQ22 B- 1BQ23 B- 3CQ25 B- 4BQ101 B- 1AQ102 B- 2AQ103 B- 2BQ104 B- 2AQ105 A- 2AQ106 A- 2AQ201 A- 3CQ202 B- 3B
Q204 B- 2BQ205 B- 2BQ206 B- 3BQ301 A- 1AQ401 A- 4BQ402 B- 4AQ403 B- 3AQ404 B- 4AQ601 A- 4BQ602 A- 4DQ603 A- 4DQ604 B- 5AQ605 B- 5BQ606 B- 4A DIODE D1 B- 5CD13 A- 5AD14 A- 3BD15 A- 4CD16 A- 5CD17 B- 2AD18 A- 5AD19 A- 5AD20 B- 4BD21 A- 5AD22 A- 5AD24 A- 5AD26 A- 5AD27 A- 5AD101 B- 2BD102 A- 2AD103 A- 2BD104 A- 2BD105 A- 2BD106 A- 2BD107 B- 2AD108 A- 2AD201 B- 3BD202 B- 2BD204 A- 1CD205 A- 1CD206 A- 1CD207 A- 1BD208 A- 1BD209 A- 1BD301 A- 1AD302 A- 1AD303 A- 1BD304 A- 1BD401 A- 3BD402 B- 4AD403 B- 4AD404 B- 3AD405 B- 3AD406 B- 3AD407 B- 4AD408 A- 4AD409 B- 4AD410 B- 3AD601 A- 4DD602 B- 4BD603 A- 4CD604 A- 4CD605 A- 4DD606 A- 4DD607 A- 4CD608 A- 4CD609 A- 4D
D610 A- 4DD611 A- 4DD612 A- 4BD613 A- 4BD614 A- 4CD615 B- 5BD616 A- 4DD617 B- 4DD618 A- 4DD619 B- 4A RESISTOR R2 B- 4BR3 B- 4BR4 B- 4BR5 A- 1DR21 A- 5AR22 A- 5AR23 A- 5AR24 A- 5AR25 A- 5AR26 A- 5AR27 B- 4BR28 A- 5AR29 B- 4BR30 A- 5AR31 A- 5AR32 A- 5AR33 A- 4AR34 A- 4AR35 B- 3BR36 B- 3BR37 A- 3BR38 B- 3BR39 B- 3BR40 B- 3BR41 A- 5CR42 B- 2AR43 A- 5CR44 A- 4CR45 A- 5CR46 A- 5CR47 A- 4CR48 B- 3BR49 A- 4CR50 A- 4CR51 B- 3BR52 B- 3BR53 B- 3AR54 B- 3BR55 B- 3AR56 A- 5CR57 B- 3AR58 A- 5CR59 A- 5CR60 A- 5CR61 A- 5CR62 B- 4BR63 A- 5CR64 B- 3AR65 B- 3BR66 B- 2AR67 B- 2AR68 B- 2AR69 B- 4CR70 B- 4CR71 B- 3BR72 B- 3CR73 B- 1B
R74 B- 1BR75 B- 4AR76 B- 4AR77 B- 4BR78 A- 5BR79 A- 5BR80 A- 5AR81 B- 4BR82 B- 4BR83 B- 3CR84 B- 3CR103 B- 1AR104 B- 1AR105 B- 1AR106 B- 1AR108 B- 1AR109 B- 1AR110 B- 1AR111 B- 1AR112 B- 2BR113 B- 1BR114 B- 2BR115 B- 2BR116 A- 1AR117 B- 2BR118 B- 1AR119 B- 1BR120 B- 1AR121 B- 2BR122 B- 2BR123 B- 1AR124 B- 1AR125 B- 2BR126 B- 2AR127 B- 2BR128 B- 2BR129 B- 2AR130 B- 1AR131 A- 2AR132 B- 2AR133 B- 2AR134 B- 2AR135 B- 2AR136 A- 2AR137 A- 2AR138 A- 2AR139 A- 2AR140 A- 2AR141 A- 2AR142 A- 2AR143 A- 2AR145 B- 1AR146 B- 2AR147 B- 1AR203 B- 2BR204 B- 3BR211 B- 3BR212 B- 3BR213 B- 2BR214 A- 2BR215 A- 2BR216 A- 2BR217 A- 2CR218 A- 2CR219 A- 2CR220 A- 2CR221 A- 2CR222 A- 2BR223 A- 2B
R224 A- 2BR225 A- 2BR226 A- 3BR227 A- 3BR228 A- 3BR229 B- 2BR230 B- 2BR231 B- 3BR233 A- 3BR235 B- 3BR238 B- 3BR239 B- 3CR240 B- 3CR241 B- 2BR242 B- 3CR243 B- 3CR244 B- 2BR245 B- 2BR247 B- 2BR248 B- 2BR250 B- 2BR251 B- 2BR256 A- 2BR258 B- 2BR259 B- 2BR260 B- 2BR261 B- 2BR262 A- 2CR265 B- 2BR266 B- 2BR267 A- 2BR268 A- 2BR269 A- 1BR270 A- 1CR271 B- 2BR272 A- 1CR273 B- 2BR274 B- 2BR275 B- 2BR276 B- 1BR277 B- 1BR278 A- 2CR280 B- 3BR281 A- 2BR282 A- 2BR302 A- 1AR303 A- 1AR304 A- 1AR305 A- 1BR307 A- 1AR308 A- 1BR309 A- 1AR310 A- 1AR311 A- 1AR312 A- 1AR313 A- 1BR314 A- 1BR315 A- 1BR316 A- 1AR317 A- 1AR318 A- 1BR319 A- 1AR320 A- 1AR321 A- 1AR322 A- 1AR323 A- 1AR324 A- 1AR325 A- 1AR326 A- 1A
R407 B- 3AR408 B- 3AR416 A- 3AR418 B- 5AR420 A- 4BR421 A- 4BR422 A- 4BR423 A- 4BR424 A- 4BR425 A- 4BR426 A- 4BR427 A- 4BR428 A- 4BR429 A- 4BR431 A- 3BR432 A- 3BR433 A- 3BR434 A- 4BR435 A- 4AR436 A- 3BR437 A- 3BR438 B- 4AR439 B- 4AR440 B- 4AR441 B- 4AR442 A- 4BR443 A- 4BR444 B- 4BR445 A- 4AR446 A- 4AR447 A- 4BR448 A- 4BR449 A- 4AR450 A- 4BR451 A- 4AR452 A- 4AR453 A- 4AR454 A- 4AR455 A- 4AR456 A- 4AR457 A- 4AR458 A- 4AR459 A- 4AR460 A- 4AR461 A- 4AR462 B- 3BR463 A- 4AR464 A- 4AR465 A- 4AR466 A- 4AR467 A- 4AR468 A- 4AR469 A- 4AR470 A- 4AR471 A- 4AR472 A- 4AR473 A- 4BR474 A- 4BR475 A- 4BR476 A- 4BR477 A- 4BR478 A- 4AR479 A- 4BR480 A- 4AR481 A- 4BR482 A- 4AR483 B- 4AR484 A- 4BR485 B- 4A
R486 B- 4AR487 A- 4BR488 A- 3BR489 B- 5AR490 A- 4AR491 A- 4AR492 A- 4AR493 A- 4AR494 A- 2BR495 A- 2BR496 A- 2BR497 A- 2BR498 A- 3BR499 B- 3AR500 A- 3BR501 B- 4AR502 B- 4AR503 B- 3AR504 A- 3BR505 B- 3AR506 A- 3AR507 A- 3AR508 A- 3AR509 A- 2AR511 B- 3AR512 A- 3BR513 A- 3BR514 A- 3BR516 B- 3AR517 A- 3BR518 A- 3AR519 B- 3AR520 B- 3AR522 B- 4AR523 B- 4AR524 B- 4AR525 A- 3BR526 A- 3AR527 B- 4AR528 B- 4BR529 B- 3BR530 B- 3BR531 B- 3BR532 B- 4BR533 B- 3BR534 B- 3BR535 A- 3BR536 A- 4BR537 A- 4BR538 A- 3BR539 B- 3AR613 B- 4DR614 A- 4DR615 B- 5BR616 A- 4DR617 A- 4DR618 B- 4BR619 A- 5BR620 A- 4BR621 A- 4BR622 B- 5BR623 B- 4CR624 A- 4DR625 B- 4DR626 A- 4DR627 B- 4DR628 B- 4DR629 A- 4DR630 B- 4C
R631 B- 4CR632 A- 4DR633 B- 4CR634 B- 4DR635 A- 4DR636 A- 4DR637 A- 4DR638 A- 4DR639 A- 4DR640 A- 4DR641 A- 4DR642 A- 4DR643 B- 5DR644 B- 5BR645 B- 5AR646 B- 5BR647 B- 5BR648 B- 5AR649 B- 5BR650 B- 4DR651 B- 5DR652 B- 5BR653 B- 5BR654 B- 5AR655 B- 5BR656 A- 4DR657 A- 4DR658 B- 4BR659 B- 4DR660 A- 4BR661 A- 4BR662 A- 4BR663 A- 4BR664 A- 4BR665 A- 4BR666 B- 4BR667 B- 4BR668 A- 4BR669 A- 4BR670 A- 5BR671 B- 4BR672 B- 4BR673 A- 4BR674 A- 4BR675 A- 4BR676 A- 4BR677 A- 4BR678 A- 5BR679 A- 5BR680 A- 5BR681 B- 4A CAPACITORC1 B- 5DC2 B- 5DC3 B- 5DC4 B- 5AC5 B- 3CC11 A- 5AC12 B- 4AC14 A- 5AC15 A- 5AC16 A- 5AC17 A- 5AC18 A- 5AC19 A- 5AC20 B- 4BC21 B- 5BC22 B- 4C
C24 A- 5A
C25 B- 4BC26 B- 4CC27 A- 5AC28 B- 5BC29 B- 4AC30 B- 5CC31 A- 5AC32 A- 5CC33 B- 3BC34 A- 5CC35 B- 3BC36 A- 4CC37 B- 3BC38 B- 3BC39 B- 2AC40 B- 3BC41 B- 2AC42 A- 4CC43 B- 3BC44 B- 3BC45 A- 5CC46 B- 2AC47 A- 4CC48 A- 5CC49 B- 3AC50 B- 3BC51 B- 3BC52 B- 3AC53 A- 5CC54 A- 5CC55 B- 3BC56 B- 4BC57 B- 3BC58 B- 3AC59 B- 3AC60 B- 2AC61 B- 2AC62 B- 2AC63 B- 2AC64 B- 4CC65 B- 4CC66 B- 4CC67 B- 1BC68 B- 3CC69 B- 3BC72 A- 1AC73 A- 1AC74 A- 5AC75 A- 5AC76 A- 5AC101 A- 2AC102 B- 1AC103 B- 1AC104 B- 1AC105 B- 1AC108 B- 2BC109 B- 2BC110 B- 2BC111 B- 2BC112 B- 2BC113 A- 1AC114 B- 1AC115 B- 2AC116 B- 2BC117 B- 2AC119 B- 1AC120 A- 2AC121 B- 2A
C122 B- 1AC123 A- 2BC124 A- 2BC125 B- 2AC126 B- 1AC127 A- 2BC128 A- 2BC129 A- 2AC130 B- 2AC131 A- 2AC132 A- 2AC133 A- 2AC134 A- 2AC135 A- 2AC136 A- 2AC137 A- 2AC138 A- 2AC139 B- 1AC140 B- 1AC141 B- 1AC142 B- 1AC143 B- 1AC144 B- 1AC145 B- 1AC146 B- 1AC147 B- 1AC148 B- 1AC201 A- 2CC207 A- 1CC211 B- 3BC212 B- 3BC213 B- 2BC214 B- 2BC216 A- 2BC217 A- 2CC218 A- 2CC219 A- 2CC220 A- 2CC221 A- 2CC222 A- 2CC223 A- 2CC224 A- 2CC225 A- 2CC226 A- 2BC227 A- 2BC228 A- 2CC229 A- 3CC230 A- 3CC231 A- 3BC232 B- 3CC233 A- 3CC234 A- 3CC235 B- 2BC236 B- 2BC237 B- 1BC238 A- 3CC239 B- 2BC241 B- 3CC242 B- 2CC243 B- 2CC244 B- 2CC245 B- 2CC247 B- 2CC249 B- 2CC250 A- 2CC251 B- 2BC252 B- 2BC253 A- 1BC254 A- 1C
C255 A- 1CC256 A- 1BC257 A- 1BC258 A- 1CC259 A- 1CC260 B- 2CC261 A- 1BC262 A- 1CC263 B- 2BC264 A- 1CC265 A- 1CC266 B- 1CC267 A- 1DC268 A- 1DC270 B- 2BC271 B- 2BC272 B- 2BC274 A- 3BC304 A- 1AC305 A- 1AC306 A- 1AC307 A- 1BC308 A- 1BC309 A- 1BC310 A- 1AC311 A- 1BC312 A- 1AC313 A- 1AC314 A- 1AC315 A- 1AC316 A- 1AC317 A- 1AC319 A- 1BC320 A- 1BC321 A- 1AC322 A- 1AC323 A- 1AC324 A- 1AC325 A- 1AC326 A- 1AC327 A- 1AC328 A- 1AC329 A- 1AC330 A- 1AC331 A- 1AC332 A- 1AC333 A- 1BC334 A- 1BC335 A- 1AC336 A- 1AC337 A- 1BC338 A- 1AC339 A- 1AC340 A- 1AC341 A- 1AC342 A- 1AC343 A- 1AC344 A- 1AC345 A- 1AC346 A- 1AC347 A- 1AC405 A- 2AC410 B- 5AC411 B- 5AC412 B- 5AC414 A- 3AC415 A- 3AC416 A- 3AC417 A- 5B
C418 A- 4BC419 A- 4AC420 A- 4BC421 B- 4AC422 B- 4AC423 A- 5BC424 B- 4AC425 B- 4AC426 A- 5BC427 A- 5AC428 B- 4AC429 B- 4AC430 A- 5AC431 B- 4AC432 A- 5AC433 A- 4BC434 B- 4BC435 A- 5BC436 A- 4BC437 B- 4BC438 A- 4BC439 B- 4AC440 B- 4BC441 B- 4AC442 B- 4BC443 B- 4AC444 B- 4AC445 A- 4BC446 B- 4BC447 A- 4BC448 B- 4BC449 B- 4AC450 A- 4BC451 B- 4BC452 B- 4BC453 B- 4BC454 A- 4BC455 B- 4AC456 B- 4BC457 B- 4AC458 B- 4AC459 B- 4BC460 B- 4AC461 B- 4BC462 A- 4BC463 B- 4AC464 B- 4BC465 B- 4AC466 B- 4BC467 B- 4AC468 B- 4BC469 B- 4AC470 B- 4AC471 B- 4AC472 B- 4BC473 B- 4BC474 B- 4BC475 B- 4BC476 A- 3AC477 A- 3BC478 A- 3BC479 A- 3BC480 A- 3BC481 A- 4BC482 A- 4BC483 A- 4BC484 B- 4AC485 B- 4AC486 B- 4A
C487 B- 4AC488 B- 4AC489 B- 4AC490 A- 4BC491 B- 3AC492 B- 4AC493 A- 3BC494 A- 3BC495 A- 3BC497 A- 2BC498 B- 3AC501 B- 4AC502 A- 3BC503 B- 3AC504 A- 3BC505 B- 3AC506 B- 3AC507 B- 3AC509 B- 3AC510 A- 3BC511 B- 4AC514 B- 3AC515 A- 3AC516 A- 3AC517 A- 2AC518 A- 2AC519 B- 4AC520 B- 4AC521 B- 4AC522 B- 4AC523 B- 4AC524 A- 3BC525 A- 3BC526 B- 3BC527 B- 3BC528 B- 3BC605 B- 5BC606 B- 4BC607 A- 5BC608 A- 4CC609 A- 5DC610 A- 5CC611 A- 5CC612 A- 5CC613 A- 4DC614 A- 4DC615 A- 4DC616 A- 4DC617 A- 4DC618 A- 4DC619 A- 4DC620 A- 4DC621 A- 4DC622 A- 4DC623 A- 4DC624 A- 4DC625 A- 4DC626 B- 5BC627 B- 5AC628 B- 5BC629 B- 5BC630 B- 5DC631 B- 5BC632 B- 5BC633 B- 5AC634 B- 5BC635 A- 4DC636 A- 4BC637 A- 4D
C638 A- 4BC639 A- 4BC640 A- 4BC641 A- 4BC642 A- 4BC643 A- 4BC644 A- 4BC645 A- 4BC646 A- 4BC647 A- 4BC648 A- 4BC649 A- 4BC650 A- 4BC651 B- 4BC652 A- 4BC653 A- 4BC655 A- 4BC656 A- 4BC657 B- 4BC658 B- 4BC659 A- 4BC660 A- 4DC661 B- 4BC663 A- 4CC664 A- 4DC665 A- 4D OTHER X401 A- 4BX402 A- 3B TH201 A- 1BTH202 A- 1DTH203 A- 2BTH401 A- 4B CN1 B- 3ACN2 B- 5ACN3 B- 5ACN11 B- 4ACN12 B- 4ACN13 B- 4ACN14 B- 5ACN15 B- 5ACN16 B- 5ACN17 B- 4ACN18 A- 5BCN19 B- 5CCN20 B- 4DCN21 B- 4ACN22 B- 2BCN23 B- 2BCN24 B- 2ACN25 B- 1BCN26 B- 2CCN27 B- 2CCN28 B- 3BCN29 B- 3BCN30 B- 2BCN31 B- 2BCN32 B- 2BCN33 B- 1ACN34 A- 1ACN35 A- 1ACN36 A- 1ACN37 A- 1ACN38 A- 1ACN39 A- 1ACN40 A- 1A
CN41 A- 1ACN42 A- 1ACN43 A- 1ACN44 A- 1ACN45 A- 1ACN46 A- 1ACN47 A- 1ACN48 B- 1ACN49 B- 1ACN50 A- 2ACN51 A- 3BCN52 A- 3ACN53 A- 3BCN54 A- 3ACN55 B- 3BCN56 A- 4BCN57 B- 4ACN58 B- 4ACN59 B- 4ACN60 B- 4ACN61 B- 4BCN62 A- 4BCN63 A- 4BCN64 A- 4ACN65 A- 4ACN66 A- 4ACN67 B- 3BCN68 B- 3BCN69 A- 4ACN70 A- 4BCN71 A- 3ACN72 A- 3BCN74 B- 4ACN75 B- 4ACN76 B- 3ACN77 B- 3ACN78 B- 3ACN79 B- 2ACN80 B- 3ACN81 B- 3BCN82 B- 3BCN83 A- 3ACN85 A- 3ACN86 B- 4ACN87 B- 4BCN88 B- 4DCN89 B- 3BCN90 B- 5BCN91 B- 4BCN92 B- 2BCN93 B- 3CCN94 A- 4ACN95 B- 4DCN96 B- 4DCN97 B- 4DCN98 A- 4B CP301 A- 1ACP302 A- 1ACP303 A- 1ACP401 A- 3BCP402 A- 4ACP403 B- 5ACP404 B- 5ACP405 B- 4ACP406 A- 3BCP407 A- 3BCP408 A- 3ACP409 A- 3A
CP410 A- 3ACP411 A- 2ACP412 A- 3ACP413 A- 3ACP414 A- 3ACP601 A- 5BCP602 A- 5BCP604 A- 4BCP605 A- 4B E11 A- 5CE101 B- 1A F1 B- 5CF2 B- 5BF3 B- 4DF4 B- 4BF5 B- 4CF6 B- 4D J1 A- 4DJ2 A- 5D L1 A- 1DL2 A- 1DL3 A- 1DL4 A- 1CL5 A- 1CL6 A- 1BL7 A- 2AL11 B- 3AL12 A- 5CL13 A- 5CL14 B- 2BL15 A- 5CL16 B- 3BL17 B- 3BL18 A- 1AL19 B- 3BL101 B- 1AL102 B- 1AL103 B- 1AL104 B- 1AL105 B- 2AL106 B- 1AL107 B- 2AL108 A- 2AL109 A- 2BL110 A- 2BL111 A- 2BL112 A- 2BL113 A- 2BL115 A- 2AL116 A- 2AL117 A- 2AL118 A- 2AL119 B- 2AL120 B- 1AL121 B- 1AL122 B- 1AL123 B- 1AL124 B- 1AL207 B- 3BL208 B- 2BL209 A- 2CL210 A- 2CL211 A- 2BL212 A- 2BL213 A- 3C
L214 A- 3BL215 A- 3CL216 A- 3BL217 B- 1BL218 B- 3CL219 B- 2CL220 B- 2CL221 B- 2CL222 A- 2BL223 A- 1CL224 A- 1CL225 B- 2BL226 B- 1CL227 A- 1BL302 A- 1BL303 A- 1BL304 A- 1A
L305 A- 1AL306 A- 1AL307 A- 1AL308 A- 1BL309 A- 1BL310 A- 1BL311 A- 1BL312 A- 1AL313 A- 1AL314 A- 1AL401 A- 3AL402 A- 4BL403 A- 5BL404 A- 4BL405 B- 4AL406 B- 4BL407 B- 4BL408 B- 4BL409 B- 4BL410 B- 4BL411 B- 4BL412 B- 4BL413 A- 3BL414 A- 3BL415 A- 3AL416 A- 3AL417 B- 4AL418 B- 4AL419 A- 3AL420 A- 4BL601 A- 4BL602 A- 4BL603 A- 4D
(No.RA054<Rev.001>) 2-8 2-8 (No.RA054<Rev.001>)
B
A
4321
B
A
4 3 2 1
R87
R86R85
R8
4
R8
3
R8
2
R81
R8
0
R7
9
R75R74R73R72
R7
1
R70R69R68R67
R6
6
R64
R6
3
R6
2
R6
1
R60
R5
8 R5
7
R5
6
R5
1
R50
R49
R48
R47
R4
6
R4
5R
44
R43
R4
2
R41
R4
0 R39
R38
R3
7
R36R21
R2
0
R1
9R
18
R17
R16
R1
5
R1
4
R7
R6
R5
R4 R
2
R1
Q6
Q4
Q3
Q1
L14
L1
3
L12
L11
L1
0
L9
L8
L6
L3L
2
L1
D3
2D
30
D28
D27
D2
6
D2
4
D22
D2
1
D2 D1
C7
3
C7
2
C7
1
C7
0
C6
8
C67
C6
6
C6
4
C6
2
C6
1
C59
C5
8
C5
7
C5
6
C5
5
C5
4
C5
3
C5
2
C5
1
C5
0C
49
C4
7
C46
C45
C41
C4
0
C39
C3
8
C3
7
C3
6
C35
C34
C33
C30
C2
8
C2
2
C21
C20
C17
C16
C15
C1
4
C13
C12
C11
C9
C8
C7
C6C
3
C2
C1
IC4
IC3
IC6
IC5CN3
CN5
CN7
CN6
IC1
R77
R33
R3
2
R31
R3
0
R2
9
R2
8R2
7
R25
R2
4
R23
R22
R13
R12
R11
R1
0
R9
R8
Q8
Q2
D34
D33
D2
0
D18 D17
D1
6
D1
5
D12 D11
D1
0
D9
D6 D5
D4
D3
C65
C2
6
C2
5C2
4
J7C-0194-00XC3-050
J1
SUB UNIT (XC3-050M-00)
--- Component side view (J7C-0194-00) ---
--- Foil side view (J7C-0194-00) ---
A-1C
Side Y axisX axis
ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one
interval.
REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION
IC IC1 B- 1BIC3 B- 1AIC4 B- 1BIC5 B- 1AIC6 B- 2B TRANSISTORQ1 B- 2BQ2 A- 1BQ3 B- 1BQ4 B- 1BQ6 B- 1BQ8 A- 3A DIODE D1 B- 3BD2 B- 3BD3 A- 4BD4 A- 4AD5 A- 4AD6 A- 2AD9 A- 1AD10 A- 4AD11 A- 3AD12 A- 2AD15 A- 1BD16 A- 4BD17 A- 3AD18 A- 3AD20 A- 1BD21 B- 1AD22 B- 1AD24 B- 1AD26 B- 1AD27 B- 1AD28 B- 1AD30 B- 1AD32 B- 1AD33 A- 1BD34 A- 1A RESISTOR R1 B- 3BR2 B- 3BR4 B- 3BR5 B- 3BR6 B- 3BR7 B- 3BR8 A- 4BR9 A- 4AR10 A- 4AR11 A- 2AR12 A- 1BR13 A- 1AR14 B- 3BR15 B- 3BR16 B- 1AR17 B- 1AR18 B- 3AR19 B- 3BR20 B- 3AR21 B- 3BR22 A- 1BR23 A- 4AR24 A- 3AR25 A- 2AR27 A- 3A
R28 A- 4AR29 A- 1BR30 A- 1BR31 A- 4BR32 A- 3AR33 A- 3AR36 B- 1BR37 B- 1BR38 B- 1BR39 B- 1BR40 B- 1BR41 B- 1BR42 B- 1BR43 B- 1AR44 B- 1BR45 B- 1BR46 B- 2BR47 B- 1AR48 B- 1BR49 B- 1AR50 B- 1AR51 B- 1AR56 B- 1AR57 B- 1AR58 B- 1AR60 B- 1BR61 B- 1AR62 B- 1AR63 B- 1BR64 B- 2BR66 B- 2AR67 B- 2AR68 B- 2AR69 B- 2AR70 B- 2AR71 B- 2AR72 B- 2AR73 B- 2AR74 B- 2AR75 B- 2AR77 A- 3AR79 B- 2BR80 B- 2BR81 B- 2AR82 B- 1AR83 B- 1AR84 B- 1AR85 B- 2BR86 B- 2BR87 B- 3B CAPACITORC1 B- 3AC2 B- 2BC3 B- 2BC6 B- 2BC7 B- 2BC8 B- 2BC9 B- 3BC11 B- 3BC12 B- 3BC13 B- 2BC14 B- 2BC15 B- 3BC16 B- 3BC17 B- 3BC20 B- 3BC21 B- 3B
C22 B- 3BC24 A- 3AC25 A- 4AC26 A- 1BC28 B- 1BC30 B- 1BC33 B- 1AC34 B- 1BC35 B- 1AC36 B- 2AC37 B- 2AC38 B- 2AC39 B- 1BC40 B- 1AC41 B- 1AC45 B- 1BC46 B- 1BC47 B- 3AC49 B- 2AC50 B- 2AC51 B- 2AC52 B- 2AC53 B- 2AC54 B- 2AC55 B- 2AC56 B- 2AC57 B- 2AC58 B- 2AC59 B- 1AC61 B- 3AC62 B- 3AC64 B- 3AC65 A- 3AC66 B- 3AC67 B- 3BC68 B- 3AC70 B- 1AC71 B- 1AC72 B- 1AC73 B- 1A OTHER CN3 B- 2ACN5 B- 2ACN6 B- 3ACN7 B- 3B J1 A- 1A L1 B- 2BL2 B- 3BL3 B- 2BL6 B- 2AL8 B- 3AL9 B- 2BL10 B- 3AL11 B- 1BL12 B- 1AL13 B- 1AL14 B- 1A
(No.RA054<Rev.001>) 2-9 2-9 (No.RA054<Rev.001>)
B
A
321
B
A
3 2 1
R29
R27
R25
R24
R23
R22
R19
R16
R15
R14
R11
R8
R7
R4
R3 R2
R1
L14L13
L6
L3
L2
L1
IC7 D18
D17
CP
2
CP
1
CN9
CN8
CN7
CN
3
CN2
C50C49C48
C47C46
C45 C44
C40
C29
C27C26
C25
C24
C23
C7
C6
C5C3
C2
C1
IC1CN5IC
4
CN1
IC2
IC3 IC6
X2
X1
R26
R21R18
R13
R12
R10
R9Q1
L15
L11
L9
L8
L7
L5
L4
IC5
E1
CN6
CN4
C68
C39
C38
C37
C36
C35
C34
C33
C32
C31
C30
C28
C22
C21
C20
C19
C18
C17
C16
C15
C14
C13
C12
C11
C10
C9
C8
C4
-10J7C-0037
XC2-003/004
MODULE (BT/GPS) UNIT (XC2-0040-10 (NX-3720H(G), NX-3720(G), NX-3820H(G), NX-3820(G)))
--- Component side view (J7C-0037-10) --- --- Foil side view (J7C-0037-10) ---
A-1C
Side Y axisX axis
ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one interval.
REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION
IC IC1 B- 2AIC2 B- 3BIC3 B- 3AIC4 B- 3AIC5 A- 2BIC6 B- 3BIC7 B- 3B
TRANSISTORQ1 A- 1B
DIODE D17 B- 1BD18 B- 1B
RESISTOR R1 B- 3AR2 B- 2AR3 B- 3AR4 B- 3A
R7 B- 3AR8 B- 3BR9 A- 1BR10 A- 1BR11 B- 3AR12 A- 1BR13 A- 1BR14 B- 3AR15 B- 1BR16 B- 1BR18 A- 2BR19 B- 1BR21 A- 2BR22 B- 3AR23 B- 1BR24 B- 1AR25 B- 2AR26 A- 1BR27 B- 2AR29 B- 2B
CAPACITORC1 B- 3BC2 B- 3BC3 B- 3AC4 A- 1BC5 B- 3AC6 B- 3AC7 B- 3AC8 A- 1BC9 A- 1BC10 A- 1BC11 A- 2BC12 A- 1BC13 A- 1BC14 A- 1BC15 A- 1BC16 A- 2BC17 A- 1BC18 A- 1BC19 A- 1BC20 A- 2B
C21 A- 2BC22 A- 2BC23 B- 1BC24 B- 1BC25 B- 1BC26 B- 1BC27 B- 1BC28 A- 2BC29 B- 1BC30 A- 2BC31 A- 2BC32 A- 2BC33 A- 2BC34 A- 2BC35 A- 2BC36 A- 2BC37 A- 2BC38 A- 1BC39 A- 2BC40 B- 1AC44 B- 3B
C45 B- 3BC46 B- 2AC47 B- 2AC48 B- 3BC49 B- 2BC50 B- 2BC68 A- 2A
OTHER X1 A- 1BX2 A- 2B
CN1 B- 3BCN2 B- 2BCN3 B- 2BCN4 A- 2BCN5 B- 1ACN6 A- 1ACN7 B- 2ACN8 B- 1BCN9 B- 2B
CP1 B- 3BCP2 B- 2B
E1 A- 2B
L1 B- 3BL2 B- 3AL3 B- 3AL4 A- 1BL5 A- 1BL6 B- 1AL7 A- 2BL8 A- 2BL9 A- 1BL11 A- 2BL13 B- 3BL14 B- 3BL15 A- 2A
A
1
2
3
4
5
B C D E F G(No.RA054<Rev.001>) 2-10 2-10 (No.RA054<Rev.001>)
EXT SP
RF
SPG
SP+
RF POWER MODULE
DR
AIN
BIA
S
1
IC601
RF
OU
TP
UT 4
ST
BY
XC1-183(UHF)
IC201
HOOK/RXD/D-2
RF
INP
UT
ME
TX-RX UNIT
12
-
DM/KVL
AF AMP
IN2
8
GA
TE
BIA
S
R5
CN1
+
PTT/TXD
IN11
ANT
SUB UNIT
J1
+
SB
E
-
INT SP
GN
D
MIC
BLC/D+2
XC1-182(VHF)
15
SB
J1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
13.6 V(K,K2)
13.2 V(E)
D[2]
/KEYINT
60
I2CCK
60
SP+
D[0]
1
D[1]
1
SPG
SPG
NC
SP+
SP+
I2CDT
SPG
DM/KVL
GND
P_TEMP
/PSW
R_SET0
R_SET1
RXD
USB_D-
TXD
GND
NC(IGN)
/PTT
USB_D+
ME
GND
GND
1
J2
BT/GPSGPS ANT
CN
2
1
20G
PS
_P
WR
GN
D
GN
D
GP
S_
AL
M
GP
S_
AN
T_
SW
GP
S_
PA
_E
N
/BT
_S
HU
TD
OW
N
WC
LK
BC
LK
BT
_A
UD
_D
I
BT
_A
UD
_D
O
RT
S2
CT
S2
RX
D2
TX
D2
BT
_S
W
GP
SB
T_
DE
T
GN
D
54
M
54
M
CN
1
1
20
CN
5
CN7
CN5
D7
RSTB
ESD_GND
/RD
CN6
VDDI
23
VG
VDD
VSS
VD1
V0
1
LC
D A
SS
Y
XC3-050
2
1
VC
C
NC
1
oU
T2
PP
NC
2
oU
T1
GN
D
NC
GND
GND
GND
GND
SB
SB
SB
SB
D[3]
D[4]
D[5]
NC
54M
NC
32M
NC
18M
NC
GND
NC
MIC/VBUS
/CS
LCDRST
/RD
D[7]
D[6]
/WR
A[23]
R_SET2
GND
IGN
SP2
DETO
DATAI
FCN2
FCN3
FCN4
FCN5
FCN1
50AC
HR1
HR2
GND
FCN6
DC Supply
D[1]
D[3]
SPG
SPG
NC
SP+
SP+
I2CDT
SPG
DM/KVL
ESD_GND
P_TEMP
/PSW
R_SET0
R_SET1
NC
RXD
NC
USB_D-
GND
GND
TXD
GND
GND
GND
NC(IGN)
SB
SB
SB
SB
NC
54M
NC
32M
NC
18M
GND
NC
MIC/VBUS
/CS
LCDRST
/RD
D[7]
D[6]
/WR
A[23]
R_SET2
D[2]
D[5]
/KEYINT
I2CCK
D[4]
SP+
/PTT
D[0]
USB_D+
ME
GND
GND
ESD_GND
XV0
VM
CSB
D6
D5
D4
D3
D2
D1
D0
/WR
A0
ESD_GND
1
12
GND
S8
S9
S10
S7
S6
S5
S4
S1
S2
S3
/PSW
FL
EX
P.B
OA
RD
CN3
(K
EY
PA
D)
MODULE (BT/GPS) UNIT
XC2-004
(NX-3720H(G), NX-3720(G), NX-3820H(G), NX-3820(G) only)
INTERCONNECTION DIAGRAM
A
1
2
3
4
5
B C D E F G(No.RA054<Rev.001>) 2-11 2-11 (No.RA054<Rev.001>)
LEVEL DIAGRAM
Receiver Section
RF (Center Frequency) AF (1kHz)
C311
ANT D205 IC607
D206
C262 D207 C337 C306 IC302 IC404 C655 IC412 C661 IC608 C627 IC601
C145
To make measurements in the AF section, connect the AC level meter.
(ANT input: –53dBm, 1kHz FM, 3kHz DEV (Wide). SP output: 4W@4ohm Load)
In the RF section, use 1000pF coupling capacitor.
(The display shows the SSG input value required to obtain 12dB SINAD.)
Transmitter Section
AF (1kHz) AF (1kHz) RF (Center Frequency)
(Mod) (Local)IC607 IC404 C327 C145
MIC
D205 ANT
D206
IC303 C216 IC202 C225 Q201 C238 IC201 C250 D207 C262
* Transmit frequency : 155MHz
LPFANTSW
HPF Transceiver IC
VCO
MPU/DSP
CODEC
-120dBm -121.5dBm -122.5dBm 141mVrms
CODECMPU/DSP Pre-
DriveDrive Final LPF
ANTSW
6.0mVrms 3dBm 14.5dBm K:18.2dBm
E:15.2dBm
K:48dBm
E:45dBm
K:47.8dBm
E:44.8dBm
K:50W
E:25W
HPF
-107.5dBm
-5dBm~+5dBm
-121dBm
Transceiver IC
123.3mVrms -5~5dBm
VOL
72.1mVrms 77.4mVrms
VCO
NX-3720/3720H
A
1
2
3
4
5
B C D E F G(No.RA054<Rev.001>) 2-12 2-12 (No.RA054<Rev.001>)
Receiver Section
RF (Center Frequency) AF (1kHz)
C311
ANT D205 IC607
D206
C262 D207 C337 C306 IC302 IC404 C655 IC412 C661 IC608 C627 IC601
C145
To make measurements in the AF section, connect the AC level meter.
(ANT input: –53dBm, 1kHz FM, 3kHz DEV (Wide). SP output: 4W@4ohm Load)In the RF section, use 470pF coupling capacitor.(The display shows the SSG input value required to obtain 12dB SINAD.)
Transmitter Section
AF (1kHz) AF (1kHz) RF (Center Frequency)
(Mod) (Local)
IC607 IC404 C327 C145
MIC
D205 ANT
D206
IC303 C216 IC202 C225 Q201 C238 IC201 C250 D207 C262
* Transmit frequency : 435MHz (K2,E), 485MHz (K)
LPFANTSW
HPF Transceiver IC
VCO
MPU/DSP
CODEC
-120dBm -121.5dBm 141mVrms
CODECMPU/DSP Pre-
DriveDrive Final LPF
ANTSW
5.8mVrms 2dBm 14.2dBm K,K2:18.2dBm
E:14.5dBm
K,K2:47.7dBm
E:45.2dBm
K,K2:47.5dBm
E:45dBm
K,K2:45W
E:25W
-107.5dBm
-5dBm~+5dBm
-121dBm
Transceiver IC
149.4mVrms -5~5dBm
72.1mVrms 77.4mVrms
VOL
NX-3820/3820H
A
1
2
3
4
5
B C D E F G(No.RA054<Rev.001>) 2-13 2-13 (No.RA054<Rev.001>)
13.6V
5.0V
1.8V
3.2V3.2V
5.4V
13.6V
1.9V Reg.
RGB
TO
IN
T S
P
GND
GND
GND
SB
SB
SB
GND(SPG)
GND(SPG)
NC
SP+
SP+
SP+
GND
/PSW
GND
NC
SP+
SPG
TO
TX
-RX
UN
IT (
XC
1-1
82, X
C1-1
83)
CN
1
TO
KE
Y P
AD
LCD BACKLIGHT
KEY ILLUMINATION
NC
SB
GND(SPG)
NC(IGN)
NC
NC
NC
/PSW
S3
S2
S1
S4
S5
S6
S7
S10
S9
S8
GND
ESD
A0
/WR
D0
D1
D2
D3
D4
D5
D6
D7
/RD
RSTB
CSB
VDDI
VD1
VSS
VDD
VM
V0
XV0
VG
ESD
ESD_GND
ESD_GND
D1,D2
Analog SW
TX
D t
o R
J4
5
PT
T t
o R
ad
io
BUSSWC
HIGH=2 USBLOW=1 UART/BLC
IO EXPANDER
GND
R_SET0
R_SET1
R_SET2
ME
MIC/VBUS
/PTT
TXD
RXD
GND
DM/KVL
32M
P_TEMP
USB_D-
USB_D+
GND
I2CDT
I2CCK
/KEYINT
54M
18M
LCDRST
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
/CS
A[23]
/WR
/RD
NC
Q3,Q4,Q6
RGB LED
RJ45
TO
LC
D
50M
/LC
DR
ST
18M_LCD
18M
32M
I2CCK
I2CDT
MIC_VBUS3
SB2
BLC4_D+2
PTT_TXD3
HOOK_RXD_D-2DM_KVL3
PTT_TXD
PTT_TXD
RX
D_
50
V
S6
S5
ME
LCDBLC1
LCDBLC2 LC
DB
LC
2
KE
YB
LC
54M
KEYBLC
P_TEMP
/PSW
I2CDT
I2CCK
/KEYINT
/CS
SB
/RD
DAT[7]
DAT[6]
DAT[5]
DAT[4]
DAT[3]
DAT[2]
DAT[1]
DAT[0]
/WR
A[23]
/LCDRST
D-
D+
A[23]
/WR
DAT[0]
DAT[1]
DAT[2]
DAT[3]
DAT[4]
DAT[5]
DAT[6]
DAT[7]
/RD
/CS
32M_LCD
/PSW
50M
50
M
RX
D_
32
V
/PT
T
P_TEMP
/KE
YIN
T
MIC_VBUS
RXD_32V
TXD
DM_KVL
/PTT
ME
LE
D_
R
LE
D_
G
LE
D_
B
/TXDEN
S2
S7
BU
SS
WC
S10
BLC
S7
S3
S2
S1
S6
S5
S4
S10
S9
S8
LC
DB
LC
1
S8
S9
BL
CS
W
BLC_3
D+
D-
S4
ME3
S3
S1
LED_R
LED_G
LED_B
MIC
_V
BU
S
BL
C_
2
HOOK_RXD_D-
BLC4_D+
TX
D
DM
_K
VL
SB
LCD_GNDD
ESD_GNDE
ESD_GNDE
ESD_GNDE
ESD_GNDE
ESD_GNDE
ESD_GNDE
ESD_GNDE ESD_GND
E
ESD_GNDE
LCD_GNDD
$C
75
$C
74
$L15
$R88STBY3
GND
2
VIN4
VoUT
1
$IC7
2.2kR86
2.2kR85
100R84
LB73G0AM-004
L14
47
pC
73
47
pC
72
47
pC
71
47
pC
70
LB73H0AV-003L13
LB
73
G0
AM
-00
4
L1
2
1k
R83
1k
R82
0
R87
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
EC720AA-0523A
CN6
0R2
RSB12ZD32
RSB12ZD26
68
R77
1k
R2
71
00
p
C2
4
330
R12
330
R13
B30-2365-05D34B30-2365-05
D33
Q1SSM3K15AMFV
10
k
R6
41
00
0p
C4
7
330
R8
330
R9
B30-2365-05D4B30-2365-05
D3
NSSW206C-T865
D9
1000pC1 0R1
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
EC710AM-0560ACN7
10
00
pC
45
$C
5
$C
44
$C24$C23
$C
19
$C
18
$C
10
1kR81
$C69
4.7
uC
6
NSSW206C-T865
D16
NSSW206C-T865
D15
NSSW206C-T865
D10
1u
C68
$T
H1 -t
$C
27
$L4
100pC67
$C60
100R80
100R79
180
R31
180
R30
180
R23
180
R22
1k
R2
8
SSM6N37FE
Q8
10
0p
C2
5
LB73G0AM-004
L11
0.1uC62
LB73H0AV-003L9
LB73G0AM-004
L2
0.1
u
C1
5
10
0p
C9
100R75
100R74
100R73
100R72
100R71
100R70
100R69
100R68
100R67
100R66
100pC58
100pC57
100pC56
100pC55
100pC54
100pC53
100pC52
100pC51
100pC50
100pC49
1uC66
1uC65
1uC64
12
11
10
9
8
7
6
5
4
3
2
1
EC720AK-0512A
CN3
VD
D_
64
4
PW
M2
43
PW
M1
42
VD
D_
54
1
PW
M0
40
IRQ
N3
9
KP
Y8
38
KP
X3
37
KP
X2
36
VD
D_
43
5
VS
S_
73
4
SDA
33
SCL
32
DIR25
31
DIR24
30
VSS_6 29
KPY7 28
RESETN
27
KPX5
26
KPY4
25
KPY6
24KPX4
23
KP
Y5
22
VS
S_
52
1
NC
20
VD
D_
31
9
KP
X6
18
VS
S_
41
7
VD
D_
21
6
KP
X7
15
VD
D_
11
4
VS
S_
31
3
KP
X0
12
KPX1
11
KPY2
10
KPY3
9
KPY1
8
KPY07
VSS_26
KPY95
EXITIo0
4
KPY10
3 KPY11
2 VSS_1
1
TC35894FGIC6
VCC 10
S
9
D+
8
D-
7
oE
6GND5
2D-4
2D+3
1D-2
1D+1
BD11600NUX
IC5VCC
8
G2
7
Y1
6
A2
5GND4
Y23
A12
G11
TC7WH126FK
IC3
VCC
8
G2
7
Y1
6
A2
5GND4
Y23
A12
G11
TC7WT125FUF
IC4
VoUT
3GND2
VDD
4CE1
MM3404A50URE
IC1
SSM6N37FE
Q2
SPC10501A01D2
D1
68
0
R3
8
330
R10
330
R24
330
R11
330
R33
330
R32
330
R25
2.2
k
R5
1
2.2
kR
40
2.2
kR
42
2.2
k
R3
9
2.2
k
R4
4
2.2
k
R2
9
2.2
k
R4
8
2.2
kR
43
2.2
kR
37
2.2
kR
41
10
kR
63
10
kR
49
10kR47
1k
R36
1k
R4
5
100R62
0R15
0R7
0R19
0R16
0R20
0R18
0R60
0R58
0R61
0R14
0R57
0R56
0R6
0R
46
0R5
0R21
0R17
150R50
0R4
$R3
RB
52
1C
M-3
0D
22 MINISMDC020F
D27
LTC014EEBFS8Q3 Q4 Q6
LB73H0AV-003L8
LB73H0AV-003L6
LB73H0AV-003
L3
LB73H0AV-003L10
LB73G0AM-004
L1
EMZ6.8ND28
12345678
E58-0535-05J1
2
1
E41-2671-05CN5
ED
ZV
6.8
B
D2
4
ED
ZV
6.8
BD
30
ED
ZV
6.2
B
D2
1
0.0
1u
C3
8
0.1uC35
0.1uC34
0.1
uC
37
0.1u
C61
0.1uC33
0.1
uC
3
0.1
u
C1
3
0.1
uC
14
0.1
uC
41
10
00
pC
20
10
00
p
C2
2
$C
48
10
00
pC
461
00
0p
C4
0 10
00
pC
59
1000pC16
10
00
p
C2
1
1u
C2
8
1u
C3
0
1u
C3
6
$C
32
100p
C39
10
0p
C2
6
$C
63
100pC11
10
0p
C1
2
10
0p
C7
10
0p
C1
7
10
0p
C2
10
0p
C8
B30-2365-05D17
B30-2365-05
D6
B30-2365-05D18
B30-2365-05D11
B30-2365-05D12
B30-2365-05
D5
B30-2364-05D20
SUB UNIT (XC3-050M-00)
SCHEMATIC DIAGRAM
A
1
2
3
4
5
B C D E F G(No.RA054<Rev.001>) 2-14 2-14 (No.RA054<Rev.001>)
TX
-RX
UN
IT (
XC
1-1
82
, X
C1
-18
3)
CN
2
ANT UNCONNECTED:3.30VANT CONNECT:3.13V
GPS ANT
MODULE UNIT (BT/GPS) (XC2-004)
1.80V
3.32V
1.80V
0V
ANT UNCONNECTED:3.30VANT CONNECT:3.13V
3.30V
3.30V
0V
1.80V
1.80V
3.30V3.20V
5.30V3.32V
3.31V
1.80V
3.17V
5.34V0V
0V
CONVERTERLEVEL
IC7
CONVERTERLEVEL
IC6
IC1
CONVERTERLEVEL
GPS/BLUETOOTH
REGULATOR(33GPS)VOLTAGE
IC4
REGULATOR(18BT)VOLTAGE
IC2 IC3
DC SW
REGULATOR(33BT)VOLTAGE
19.2MHz
1.8V
3.3
V
3.3
V
3.3
V
1.8V
MSL
MSL-SL-MSL
MSL
33GPS
to ADC
to ADC
(3216)
3.3V
BT ANT
18BT
33BT
33BT
18BT
1.8V
33
BT
1.8V
3.3V
18
BT
SAW FILTERGPS
GPS&BT RTC
GPS_ALM
GPS_PA_EN_LV
18BT_TX
BT_SW
/BT
_S
HU
TD
OW
N
GPS_ANT_SW
GPS_PWR
GP
S_
PA
_E
N
BC
LK
33BT
18BT_RX 18BT_HCI_TX18BT_HCI_RX
RXD2TXD2
RTS2
CTS2
BT_AUD_DI
BT_AUD_DOWCLK
BCLK
WC
LK
BT
_A
UD
_D
O
BT
_A
UD
_D
I
RT
S2
CT
S2
TX
D2
RX
D2
18
BT
_A
UD
_IN
18
BT
_A
UD
_C
LK
18
BT
_A
UD
_O
UT
18
BT
_A
UD
_F
SY
NC
18
BT
_H
CI_
RT
S
18
BT
_T
X
18
BT
_H
CI_
CT
S
18
BT
_R
X
18
BT
_H
CI_
RX
18
BT
_H
CI_
CT
S
18
BT
_H
CI_
RT
S
18
BT
_A
UD
_F
SY
NC
18
BT
_A
UD
_IN
18
BT
_A
UD
_O
UT
18
BT
_H
CI_
TX
18
BT
_A
UD
_C
LK
L14
L13
2.2n
L15
0
R29
0
R27
CN
8
47p
C50
VoU
T3
VIN
4
GN
D2
CoN
TR
oL
1
NJM
2878F
4-3
3IC
4
CN
9
5678
4321
10*4CP1
5678
4321
10*4 CP2
0.1u
C49
0.1uC48
0.1u
C46
0.1uC47
CN
7
0
R26
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CN1
F10-3226-05E1
10k
R3
0
R18
0
R21
10k
R2
B1
16
B2
15
B3
14
B4
13
DIR312
OE11
GND10
DIR49
A4
8
A3
7
A2
6
A1
5
DIR14
VCC(A)3
VCC(B)2
DIR21
74AVC4TD245GU
IC1
0.4
7u
C7
18p
C40
1000p
C25
1k
R15
1000p
C26
1k
R19
1000p
C27
0.1
u
C29
0.1
u
C24
1000p
C23
1k
R14
0.1
uC
3
100k
R9
100k
R10
CN6
BT
_T
X_
DB
GX
CN
3
GPS_PPS_OUT
CN2
CN4
10
R16
27n
L6
L2
CE6
VSS5
NC24VoUT 3
NC1 2
VIN 1
IC3
EM6M2
Q1
10p
C9
22p
C8
0
R23
0
R24
47k
R13
47k
R12
0.1u
C4
VCC 4
oUTPUT 3GND2
VCoNT1
L77-3123-05
X1
1p
C68
CN5
0.4
7u
C2
1k
R11
1k
R8
L3
STBY3
VIN4
GND2
VoUT1
BU18TD2WNVXIC2
1uC5
0.4
7u
C1
L1
0.47uC6
(-71)10n
L7
0.1uC44
0.1u
C45
B1
16
B2
15
B3
14
B4
13
DIR312
OE11
GND10
DIR49
A4
8
A3
7
A2
6
A1
5
DIR1 4
VCC(A) 3
VCC(B) 2
DIR2 1
74AVC4TD245GU
IC7
GND1GND2
oUT IN
L11
B1
16
B2
15
B3
14
B4
13
DIR312
OE11
GND10
DIR49
A4
8
A3
7
A2
6
A1
5
DIR1 4
VCC(A) 3
VCC(B) 2
DIR2 1
74AVC4TD245GUIC6
10k
R25
10k
R22
235
4 1
L9
100
R7
100
R4
100
R1
1uC31
18p
C18
18p
C19
RN
262C
SD
18
RN
262C
SD
17
0.1uC11
0.1uC34
1uC15
L8
0.1uC33
L4
0.1uC14
VSS_RF_BT
B10
VS
S_
DC
o_
BT
A9
VD
D_
RF
_B
TB
9
BT
_T
ES
TT
MA
10
VDD1P8_FM
J8
VSS_PASYNTH_FM
J10
VB
AT
1A
2
VD
D1
P8
V_
2A
3
VD
DS
1B
3
BT
_A
UD
_C
LK
D1
BT
_A
UD
_F
SY
NC
D2
BT
_A
UD
_IN
D3
BT
_A
UD
_o
UT
C3
BT
_H
CI_
UA
RT
_T
XA
4
BT
_H
CI_
UA
RT
_R
XB
5
BT
_H
CI_
UA
RT
_C
TS
B4
BT
_H
CI_
UA
RT
_R
TS
B7
BT
_H
oS
T_
WA
KE
UP
A5
BT
FM
_n
SH
UT
Do
WN
A6
VD
D_
DIG
1E
5
VS
S_
DIG
6B
6
BT
_G
PIo
[6]
H5
BT
_G
PIo
[5]
D7
BT
_G
PIo
[4]
C5
BT
_G
PIo
[3]
D6
BT
_G
PIo
[2]
C7
BT
_T
ES
TT
PB
8
VS
S_
DP
LL
_B
TA
7
VD
D_
DC
o_
BT
A8
BT_RF
C10
VDD1P8V_BT
C8
VDD_LDoIN_CLASS1P5_BT
D8
VDD_CLASS1P5_BTD9
VDD_PPAIF_BTD10
REF_CLK_LVE7
REF_CLK_HVE8
BT_WAKEUPH10
VSS_REF_CLKE9
VSS_DIG3E10
VDD_SRAM1F9
VDD_DIG4F10
VSS_DIG1G9
VDDS2G10
FM_I2C_SDAE6
FM_I2C_SCLF6
FM_IRQG6
FM_I2S_CLKF8
FM_I2S_FSYNCF7
FM_I2S_oUTG7
FM_I2S_ING8
FM_AUD_IN_LH7
FM_AUD_IN_RH8
RTC_CLK
H9
VS
S_
LN
A_
GP
S3
K2
TE
ST
_E
NL
10
VS
S_
PA
_F
MJ9
FM
_R
FP
_o
UT
K9
FM
_R
FP
_IN
L9
VS
S_
RF
_F
MK
8F
M_
AB
GA
P_
CA
PL
8
VS
S_
AD
CP
LL
_F
MJ7
FM
_A
UD
_o
UT
_R
K7
FM
_A
UD
_o
UT
_L
L7
RE
F_
CL
K_
RE
QJ6
VD
D_
DIG
3K
6V
PP
L6
VS
S_
DIG
4J5
VD
DS
3K
5V
DD
_S
RA
M2
L5
CL
K_
RE
QP
oL
G4
VS
EN
SE
J4
IFo
RC
EL
4
GP
S_
I2C
_U
AR
T_
SE
LH
4G
PS
_P
A_
EN
G3
GP
S_
EX
T_
LN
A_
EN
H6
GP
S_
IRQ
G5
VS
S_
MIX
_G
PS
K3
VD
D_
IF_
GP
SK
4V
SS
_L
NA
_G
PS
2L
3
GP
S_
LN
A_
INL
2
VSS_LNA_GPS1
L1
VDD_PLL_GPS
J2
VSS_PLL_GPS
J1
VDD1P8_GPS
J3
GPS_TPH3
GPS_TMH2
GPS_UART_TXF5
GPS_UART_RXE3
GPS_SENS_I2C_SCLF4
GPS_SENS_I2C_SDAE4
GPS_nSHUTDoWND5
GPS_TIMESTAMPC6
GPS_PPS_oUTC4
TCXo_LDo_INH1
VSS_DIG2F3
VDD_DIG2F2
VDD_TCXoG1
VSS_TCXo_CLKG2
TCXo_CLK_LVF1
TCXo_LDo_VPRoGE1
VDDS4E2
TCXo_CLK_REQD4
VSS_DIG5C2
VDD_SRAM_LDoC1
VDD_DIG_LDo
B2
VDD1P8V_1
B1
PMTEST_1P8V
A1
IC5
0.1uC13
1uC10
0.1
uC
39
0.1
u
C22
0.1
uC
30
1u
C21
0.1
uC
28
0.1uC35
0.1u
C17
0.1u
C16
0.1uC12
22p
C37
0.1uC32
L5
1u
C20
2.5
p
C38
-32.768000k
L77-3121-05@C-FRE
X2
22p
C36
MSL
MODULE (BT/GPS) UNIT (XC2-0040-10 (NX-3720H(G), NX-3720(G), NX-3820H(G), NX-3820(G)))
P2.3
P2.4
P2.5
P1.6
P1.7
SBWTDlo
SBWTCK
P2.7
P2.6
P2.2
P2.1
P2.0
P1.5
A4
A3
TXD
RXD
P1.0
AK2401
MP2560DQ-LF-Z
PWR
R1
$C
N9
$CN10
Destination
R3
R2
R4
TX:9.0VRX:0V
5.4V
13.6V5.4V
1.8V
3.2V
13.6V
1.8V
5.0V
1.8V
3.2V
1.8V
1.8V
1.2V
1.2V
1.2V
1.2V
13.6V
5.0V
13.6V13.6V
5.0V
3.2V
3.1V3.2V
1.2V
1.8V5.0V
5.0V
1.8V
1.2V
TX:4.2VRX:4.2V
19.6V
9.0V
TX Low power:4.1VTX High power:4.6V
5.4V
TX:0.8VRX:0V
TX:1.6VRX:0V
TX:5.0VRX:0V
13.6V
VCO Buffer/LPF SHIELD CASE
54M DC/DC SHIELD CASE
50AC
SB
SP
G
TO SUB UNIT (XC3-050) CN7
TO MODULE (BT/GPS) UNIT (XC2-004) CN1 NC
(IG
N)
NC
GN
D
SP
G
SP
+
R_
SE
T0
NC
NC
R_
SE
T1
32
M
SP
+
R_
SE
T2
US
B_
D-
SP
+
GN
D
GN
D
/PS
W
A[2
3]
NC
GN
D
/WR
GN
D
NC
D[0
]
GN
D
D[1
]
GN
D
D[2
]
GN
D
D[3
]
SB
D[4
]
SB
D[5
]
ME
D[6
]
SB
D[7
]
MIC
/VB
US
/RD
SP
G
LC
DR
ST
/PT
T
/CS
P_
TE
MP
/KE
YIN
T
I2C
CK
I2C
DT
GN
D
RX
D
TX
D
DM
/KV
L
NC
GN
D
US
B_
D+
18
M
NC
54
M
CTS
RTS
+B
20
19 18
17
VCO Buffer
VCO
50
FNC6
FNC5
EXT.SP
FNC4
FNC3
FNC2
15
FNC1
RXD1
7 DATAI
14
DATO
HORN ALERT SW
13
SP212
IGN
11
SB
10
D-Sub15
9
8
6
16
5
2
1
4
3
TXD1
GND
RXD
HR
2
TXD
HR
1
RX HPF
32C
Pre-Drive
Drive
90T
90T
90T
For DDR_DVDDFor RVDD,USBFor CVDD
For DVDD IO For DVDD IO For USB
90C
90ANT
Ga
te B
ias 2
DE
T
Ga
te B
ias 1
CV
FWD
TH2
50CT
20V DC/DC
50C
12BU
31BU
BATT CHK
18M
50BU
12M
18M SWLoad Switch
/OVRB(For MSP430)
SB2(9Vreg/D-sub)
50A
SB1(HEAD/AFamp)
54M
32M
32A
AFOAMP
25VREF
DAC
12bit/4ch
DAC E-Vol
8bit/8ch
AFAMPDSUBExSP
19.2MHz
CODEC
VREF
BOOT PIN
Emulation Debug BOOT = 00011110
For Production line
UART BOOT=10010111
CN941 CN922 CN923 CN924 CN925
BO
OT
[2]
BO
OT
[3]
BO
OT
[0]
BO
OT
[7]
BO
OT
[6]
BO
OT
[5]
BO
OT
[1]
BO
OT
[4]
For DVDD IO
/FLDM
FlashROM 512Mb
LOW = UART OR USB LOADER
/FRST = OPEN DRAIN
/WP internal Pull-Up
19.2MHz
TH1
RX
SB
2
GP
SB
T_
DE
T
+B
32M
32M
32M
31BU
31BU
31BU
US
B0
_D
P
/INT15P
32M
US
B0
_D
M
/RST
50A
50A
50A
RE
V
/IN
T_
IO
PRST_MON
R_
SE
T0
R_
SE
T1
R_
SE
T2
UA
RT
2_
SW
2
UART2_SW1
/BT_SHUTDOWN
GPS_PA_EN
UMode
I2C
DT
I2C
CK
/INT15P
TXD1
RXD1
R_
SE
T1
/KEYINT
/ADC
TX
DD
RC
_D
[15]
PWR_CNT
GPS_ANT_SW
/FR
ST
19.2M
32k_I
CTS2
RXD2
UART2_SW1
G_
RX
D2
AD
D[6
]
54M
/ADC_INT
/ADC_INT
IGN
SYMTIM_IN
/OVRB
32A
SPAF_4
25REF
I2CDTI2CCK
P_
TE
MP
/VB
US
_D
ET
18
M_
1
SP
O
MIC
ME
P_
TE
MP
/CS
4
R_
SE
T0
R_
SE
T2
DA
TA
[6]
DA
TA
[7]
DA
TA
[5]
DA
TA
[4]
DA
TA
[3]
DA
TA
[2]
DA
TA
[1]
DA
TA
[0]
/OE
/WR
AD
D[2
3]
PR
ST
_M
ON
PR
ST
/KE
YIN
T
I2C
CK
I2C
DT
RX
D0
TX
D0
/PS
W
/PT
T
/IG
N
18
M
32
M
54
M
SB
1
31
BU
DA
TA
7D
AT
A6
DA
TA
5D
AT
A4
DA
TA
3D
AT
A2
DA
TA
1D
AT
A0
/CS
_L
CD
/RD
_L
CD
/WR
_L
CD
DC
DA
TA
1D
AT
A2
DA
TA
5D
AT
A4
DA
TA
7
DA
TA
3
DA
TA
6
DA
TA
0
/CS
_L
CD
/RD
_L
CD
/WR
_L
CD
DC
32M
DC
R_
AC
LK
DC
R_
DD
O/D
CR
_D
CS
/DC
R_
AC
SD
CR
_A
DI
GP
SB
T_
DE
T
AP
C1
TX
PW
R_
H_
/L
Ra
mp
_O
ffse
t
/DS
W
TX
C
AN
TS
W
AS
SW
AS
TS
W
VC
O_
MO
D
AS
SIS
T
BC
LK
PL
D
DC
R_
DI
DC
R_
DO
/DC
R_
CS
AG
CK
EE
PT
XR
X
/DC
R_
RS
T
CP
AT
T_
SW
50
C
SP
C
I2CDT
50A
SP
C
GP
S_
PA
_E
N
GP
S_
PW
R
GP
S_
AL
M
GP
S_
AN
T_
SW
D33_TXD2
APC
TXD1
RTS1
D33_RXD2
BER_DATABER_CLK
BER_EN
DI
I2CCK
BE
R_E
N
/PS
W_O
UT
50
CT
BT
_S
W
BER_DATA
BER_CLK
SP_MUTE
SBC
VC
O_
MO
D
/DCR_RST
RX
AGCKEEP
18M_1
18M_1
ATT_SW
TXPWR_H_/L
CPZ
CP
SCK1
SDO1
BC
LK
/EVCS
/PTT
/IG
N_O
UT
PA
_M
UT
E
DA
TA
[0]
/SA
VE
/WP
DCR_DI
DCR_DDO
/DCR_DCS
32
M
32M
32M
32
M
50C
50C
20
0C
20
0C
18
M_
1
12M
54M
54M
BA
T_
CN
T
SB1
DI
AFO
DEO_0
CTS1
RXD1
SB2
IGN
PLL_CLK
SB
C
SBC
SDO1SCK1/EVCS
GP
S_
AL
MG
PS
_P
WR
RE
VT
HP
2T
HP
1T
EM
P
CT
S2
SPO
PA_MUTE
SP_MUTE
CP
Z
50
C
32k_O
50
CT
50
CT
32
A
TH
P2
VREF
ME
50
CT
/BINT2
AP
C1
MCLK
MCLK
50C
CV
54
M
BT
_S
W
BT
_A
UD
_D
IB
T_
AU
D_
DO
RT
S2
WC
LK
/BT
_S
HU
TD
OW
N
BCLK
12BU_1
18
M
12BU
12BU_1
18M
18M
DD
RM
_D
[14]
MIC
32
A
18M_3
SBWTDIOSBWTCK
32M
32M
SB1
BLVL
SB2
SBC
18M
32A
12
M_
1
12
M_
1
18
M_
2
32
M_
1
32
M_
1
32
M_
1
/FL
DM
/OE
32M
50A
18M_3
/VB
US
_D
ET
DA
TA
[15
]
DM_IN
DM_OUT
/DM_EN
50A
/CS
_F
/CS
2
/CS2
/CS
2
DM_OUT
DM_IN
/DM_EN
/CS
4
+B
+B
CV
THP1
BT_AUD_DI
BT_AUD_DO
G_
TX
D2
32M
50A
32M
25REF
RTS2
/DACCS
AS
TS
W
/CS
2
TXD2
D33_RXD2
UART2_SW2
D33_TXD2
P_TXD2
P_RXD2
12M
/RST
Ra
mp
_O
ffse
t
32M
/AD
C
BL
VL
50
A
SD
I0S
DO
0S
CK
0
/CRST
18
M_
3
+B
BAT_CNT
P_TXD2
/OVRB
/IGN
P_RXD2
/IGN_OUT
/PSW_OUT
12BU
/BINT
/OVRB_OUT
PWR_CNT
/PSW
50A
/IGN
PLL1_VDDA
12M_1
PLL0_VDDA
32A
/CS3
/CS
3
AS
SIS
T
BCLK DEO_0
SCK1/DACCSSDO1
CODEC_DICODEC_DOWCLK
FC
NT
DD
RM
_D
[1]
DD
RM
_A
[12]
DD
RM
_W
E
DD
RM
_D
QS
[1]
/INT_IO
ASSW
UMode
USB0_DPUSB0_DM
50
A
50A
AD
D[9
]
DA
TA
[9]
AD
D[1
0]
DA
TA
[4]
DA
TA
[6]
AD
D[7
]
AD
D[1
5]
AD
D[1
8]
DA
TA
[15
]
DA
TA
[10
]
DA
TA
[8]
DA
TA
[11
]
DA
TA
[12
]
DA
TA
[7]
AD
D[2
]
AD
D[1
6]
AD
D[1
9]
DA
TA
[13
]
AD
D[1
4]
AD
D[8
]
DA
TA
[1]
AD
D[4
]
AD
D[1
7]
AD
D[3
]
AD
D[1
3]
AD
D[1
1]
DA
TA
[3]
/WR
AD
D[2
2]
AD
D[2
1]
AD
D[2
0]
AD
D[0
]
AD
D[1
]
AD
D[1
2]
AD
D[2
3] VER2
DA
TA
[14
]
DA
TA
[0]
DA
TA
[2]
AD
D[5
]
DA
TA
[5]
DD
RM
_A
[2]
/BIN
T2
PLD
SB
C
/OV
RB
_O
UT
WCLK
CODEC_DI
RXD0
/DCR_ACS
(TXSLOT) RTS1
/DCR_CS
DCR_ACLK
TXD0
DCR_DO
CODEC_DO
/CRST
SYMTIM_IN
I2CDT
PRST
/DSW
SDI0
ANTSW
I2CCK
/BINT
TXC
CTS1
SCK0
SDO0
DCR_ADI
18M_2
18M_1
32M_1
PLL1_VDDA
12M_1
PLL0_VDDA
32M_1
18M_1
32M_1
32M_1
18M_2
DD
RC
_B
A[1
]
DD
RC
_B
A[0
]
DD
RM
_B
A[1
]
DD
RM
_C
LK
P
DD
RM
_D
[3]
DD
RC
_D
QS
[1]
DD
RC
_D
QS
[0]
DD
RC
_D
QM
[1]
DD
RC
_D
QM
[0]
DD
RC
_C
S
DD
RC
_C
AS
DD
RC
_R
AS
DD
RC
_W
E
DD
RC
_C
KE
DD
RC
_C
LK
N
DD
RC
_C
LK
P
DD
RC
_A
[0]
DD
RC
_A
[1]
DD
RC
_A
[2]
DD
RC
_D
[4]
DD
RM
_A
[7]
DD
RC
_A
[12]
DD
RC
_A
[13]
DD
RM
_D
[15]
DD
RC
_A
[11]
DD
RC
_D
[10]
DD
RC
_A
[4]
DD
RM
_D
QM
[0]
DD
RM
_D
[13]
DD
RM
_D
[11]
DD
RM
_B
A[0
]
DD
RC
_D
[3]
DD
RM
_D
QM
[1]
DD
RM
_A
[6]
DD
RM
_R
AS
DD
RM
_A
[3]
DD
RC
_A
[6]
DD
RM
_A
[9]
DD
RC
_D
[2]
DD
RC
_D
[6]
DD
RM
_D
[5]
DD
RM
_A
[8]
DD
RM
_D
[0]
DD
RM
_C
LK
N
DD
RC
_A
[9]
DD
RC
_A
[8]
DD
RM
_A
[4]
DD
RM
_D
[12]
DD
RC
_A
[7]
DD
RC
_D
[14]
DD
RC
_D
[12]
DD
RM
_C
S
DD
RM
_C
AS
DD
RM
_C
KE
DD
RC
_A
[5]
DD
RC
_D
[1]
DD
RM
_D
[7]
DD
RC
_D
[13]
DD
RC
_D
[5]
DD
RC
_D
[9]
DD
RM
_A
[13]
DD
RM
_D
[10]
DD
RM
_A
[5]
DD
RM
_D
[4]
DD
RM
_A
[10]
DD
RM
_D
QS
[0]
DD
RM
_D
[6]
DD
RM
_D
[8]
DD
RC
_D
[11]
DD
RC
_A
[3]
DD
RC
_A
[10]
DD
RC
_D
[0]
DD
RM
_A
[1]
DD
RM
_A
[0]
DD
RM
_A
[11]
DD
RC
_D
[7]
DD
RC
_D
[8]
DD
RM
_D
[2]
DD
RM
_D
[9]
12
M_
1
12M_1
18
M_
1
DD
RM
_B
A[1
]
DD
RM
_D
QM
[0]
AD
D[1
9]
DD
RM
_A
[0]
AD
D[1
4]
DD
RM
_A
[12
]
DD
RM
_A
[6]
DD
RM
_A
[9]
DA
TA
[12
]
AD
D[1
6]
DD
RM
_D
[9]
DA
TA
[1]
AD
D[1
7]
DD
RM
_D
QS
[1]
DA
TA
[7]
AD
D[2
1]
AD
D[0
]
DD
RM
_D
[13
]
DD
RM
_B
A[0
]
DD
RM
_A
[2]
AD
D[7
]
DD
RM
_A
[1]
32M
DD
RM
_A
[13
]
DD
RM
_C
KE
DD
RM
_C
LK
P
DA
TA
[10
]
DA
TA
[13
]
/WR
DD
RM
_A
[10
]
DA
TA
[9]
DD
RM
_C
AS
/WP
AD
D[1
1]
AD
D[1
3]
DD
RM
_D
[3]
DD
RM
_D
[10
]
DA
TA
[14
]
DA
TA
[6]
DD
RM
_A
[8]
DD
RM
_D
[15
]
AD
D[8
]
AD
D[1
]
AD
D[2
0]
DD
RM
_R
AS
DA
TA
[2]
DD
RM
_A
[4]
DD
RM
_D
[11
]
AD
D[2
]
DD
RM
_D
QM
[1]
/CS
_F
DD
RM
_D
[8]
AD
D[3
]
DA
TA
[4]
DA
TA
[11
]
DA
TA
[5]
AD
D[9
]
DA
TA
[8]
DD
RM
_D
[2]
DD
RM
_D
[5]
AD
D[2
3]
AD
D[6
]
DD
RM
_A
[3]
AD
D[1
8]
DD
RM
_C
LK
N
DD
RM
_D
[6]
DD
RM
_D
[1]
DD
RM
_A
[7]
AD
D[5
]
AD
D[2
2]
AD
D[1
5]
/OE
AD
D[1
2]
DD
RM
_W
E
/FR
ST
DD
RM
_A
[5]
AD
D[4
]
DD
RM
_D
[7]
AD
D[1
0]
DD
RM
_D
[14
]
DD
RM
_A
[11
]
DD
RM
_D
[4]
DA
TA
[3]
DD
RM
_D
[12
]
DD
RM
_D
QS
[0]
DD
RM
_D
[0]
DD
RM
_C
S
FCNT
TEMP
OSCGNDB
OSCGNDB
PLL0GNDE
PLL0GNDE
PLL1GNDF
PLL1GNDFRTCGNDG
RTCGNDG
RTCGNDG
10uL12
ANT0
R5
100pC622
100pC617
0.01uC324
100pC616
100p
C332
0.1uC330
100pC615
100pC326
100p
C623
1000pC313
100pC624
$C
41
3
15
00
pC
22
2
47
00
p
C2
63
0.0
22
u
C6
53
4.7
uC
63
2
47
00
p
C2
39
$C
14
9
1u
C7
6
0.0
47
uC
75
0.1
uC
74
0.1
uC
11
0.1uC348
10
00
pC
24
5
1000pC270
10
00
p
C2
71
470pC212
100pC329
3p
C317
10
0p
C5
04
10
uC
32
1
0.1uC328
1000pC216
5p
C3
18
47
0p
C2
0
$C
10
6
68pC218
10
00
p
C2
72
470pC42
1000pC225
47
0p
C5
1
1u
C2
8
47
0p
C1
34
$C
71
$C
70
47
0p
C1
38
10
0p
C2
6
$C210
0.4
7u
C3
45
47
0p
C3
9
100pC618
10
0p
C3
22
33
00
p
C2
51
(G)
47
p
C2
24
10
00
p
C2
32
12p
C312
47
0p
C3
6
2.2
u
C3
42
0.22u
C627
1u
C316
47
0p
C1
24
10
00
p
C2
20
0.1uC336
47
0p
C1
47
0.22u
C628
10
uC
34
4
47
0p
C1
46
0.01uC314
4pC148
6pC137
15pC311
470pC21
2.2
u
C6
65
47
0p
C6
63
47
0p
C2
2
100pC335
50
1uC6
64
0.1
uC
34
7
10uC346
10
0p
C4
8
$C
27
3
$C
24
0
$C
20
3
1uC655
501uC609
2200pC29
$C
26
9
1u
C661
10
00
p
C2
5 10
00
p
C5
6
10
0p
C5
09
10
0p
C5
01
10
0p
C5
06
10
00
p
C2
7
0.1u
C340
10
0p
C5
05
10
00
p
C4
7
100pC325
1000p
C306
$C512
$C513
0.01u
C606
$C
13
5p
C319
39
0p
C6
2
39
0p
C6
1
0.1uC521
0.01uC498
0.0
1u
C5
22
0.0
1u
C4
91
0.0
1u
C4
87
1000pC523
0.01uC235
10
00
pC
12
0.1
uC
51
1
0.1
uC
52
0
0.1
uC
51
9
10
0p
C5
03
0.0
1u
C4
18
0.01u
C447
0.0
1u
C1
08
$C
40
4
$C246
1u
C315
$C
40
3
10
0p
C4
92
501u
C611
0.0
1u
C4
88
0.0
1u
C1
9
0.1u
C510
0.01u
C438
$C
24
8
0.0
47
u
C2
21
1000pC514
0.1
u
C2
60
10
00
p
C3
41
10
0p
C5
07
7p
C3
07
1000pC660
$C281
0.1
u
C4
82
10
0p
C2
49
C93-1838-052.0pC280
C93-1852-056.0pC279
C9
3-2
03
1-0
58
.0p
C2
78
C9
3-2
04
1-0
51
1p
C2
77
39
p
C2
75
15p
C274
$C
30
1
501uC610
10
00
pC
48
4
39pC320
27p
C308
0.1
u
C2
52
7p
C334
470p
C333
0.1
uC
15
10
0p
C3
43
10
0p
C3
05
25
0.1
uC4
50
.1u
C3
5
0.1
uC
64
5
0.1u
C527
0.1
uC
65
7
0.1
uC
490
0.1
u
C4
9
1u
C631
1u
C5
28
1u
C626
100pC614
16
10
u
C1
30
16
1u
C4
3
1u
C6
49
10
0p
C1
25
1u
C5
15
161u
C517
47
00
p
C4
05
1u
C4
78
1u
C7
2
501u
C612
0.0
1u
C4
12
10
00
pC
41
1
10
00
p
C4
10
10
0p
C3
04
12p
C339
100pC620
1u
C7
3
1u
C4
93
$C
20
4
$C
30
2
$C
30
3
1u
C5
26
1u
C2
4
12p
C309
1u
C462
1u
C6
59
27p
C310
$C
21
51
00
p
C2
36
16
1uC
21
1
16
1uC6
8
10
00
p
C3
38
1uC639
100p
C323
0.022uC621
22
p
C2
13
1000p
C337
1000pC331
1u
C3
27
1u
C6
47
0.0
1u
C2
14
0.0
1u
C6
08
10
0p
C6
25
1u
C4
14
1u
C3
1
0.1
uC
471
0.1
uC
470
0.1
uC
469
0.1
uC
468
1u
C6
52
1u
C1
8 0.4
7u
C1
7
0.22uC483
50
4.7
uC3
0
0.1
uC
66
2.2
u
C4
6
2.2
u
C5
5
2.2
u
C4
4
16
2.2
uC6
9
$C205
$C
20
6
1000pC254
1000pC241
10
00
pC
25
7
C9
3-1
85
2-0
56.0
pC
26
5
C9
3-1
85
2-0
56.0
pC
20
9
C9
3-1
85
2-0
56
.0p
C2
08
C9
3-1
84
6-0
54
.0p
C2
59
C9
3-1
85
2-0
5
6.0
pC
26
8
1000p
C256C93-1900-051000pC250
C93-1887-05
82pC262
C9
3-1
86
1-0
5
10
pC
20
7
0.0
1u
C4
36
0.0
1u
C4
50
0.1
uC
463
0.1
uC
428
0.1
uC
425
0.1
u
C474
0.1
uC
41
5
0.1
uC
429
0.1
u
C4
95
0.1
uC
466
0.1uC479
0.1
uC
464
0.1uC485
0.1
uC
455
0.1
uC
448
0.1
uC
461
0.1
uC
64
2
0.1
uC
47
7
0.1
uC
441
0.1
uC
41
9
0.1
uC
434
0.1
uC
451
0.1
uC
64
3
0.1
uC
42
7
0.1
uC
64
1
0.1
u
C4
75
0.1
uC
457
0.1
uC
64
4
0.1
u
C4
97
0.1
uC
42
0
0.1
uC
458
0.1uC640
0.1
uC
444
0.1
u
C6
48
0.1
uC
43
0
0.1u
C494
0.1
uC
443
0.1
uC
442
0.1
u
C5
16
0.1
uC
459
0.1
uC
467
0.1
uC
440
0.1
uC
43
2
0.1u
C638
0.1
uC
65
0
0.1
uC
465
0.1
uC
16
0.1
u
C472
0.1
uC
47
6
0.1
uC
43
5
0.1
uC
431
0.1
uC
42
6
0.1
uC
48
6
0.1
uC
42
3
0.1
u
C4
73
0.1
uC
424
0.1
uC
460
0.1u
C502
0.1
uC
41
6
C9
3-2
04
1-0
51
1p
C2
64
C9
3-2
03
5-0
59
.0p
C2
67
CC730AD1H104J0.1uC116
3.5
p
C2
53
(G)
12
pC
26
1
33pC234
$C
20
2
9p
C1
31
22
p
C2
26
$C
21
7
$C201
C9
3-1
84
9-0
55
.0p
C2
19
22
p
C2
28
7p
C1
33
9p
C132
2p
C1
28 0.7
5p
C1
29
0.5pC135
$C
10
1
5p
C4
54
39
p
C2
27
10
0p
C1
10
10
0p
C6
51
100p
C223
47
0p
C1
36
10
0p
C1
20
100pC518
10
0p
C1
12
10
0p
C2
31
10
0p
C2
47
10
0p
C2
44
1000pC230
220pC127
15pC481
18pC480
220pC123
12p
C229
22
pC
24
2
33pC109
$C
40
8
10
00
p
C2
37
47
p
C5
24
$C
40
9
47
p
C5
25
$C
40
6
$C
40
2
10
00
pC
26
6
47
pC
24
3
47
p
C6
7
$C
40
7
68
p
C6
58
10
0p
C4
45
10
0p
C4
33
$C401
10
00
pC
23
3
1000pC258
10
00
p
C2
55
1000pC238
0.0
1u
C6
35
1u
C1
11
50
1u
C3
75
01
uC
33
50
1uC
50
50
1uC4
1
10u
C637
10
00
p
C1
45
1u
C4
89
$C107
6p
C1
43
1.5pC142
12
p
C1
41
1.5pC140
6p
C1
39
10u
C437
10
u
C5
7
10u
C446
10
uC
40
10u
C452
10u
C456
10u
C453
10uC636
10u
C449
0.0
1u
C6
05
10u
C656
0.1
u
C6
07
0.1
u
C6
33
0.1
u
C6
34
10u
C646
10
00
p
C6
29
10
00
p
C6
30
1000pC613
10u
C422
47
u
C6
5
CK
73
0F
A1
H4
75
K
4.7
uC
63
50
4.7
uC3
450
4.7
uC3
2
16
10
u
C5
4
10
u
C5
8
16
10
u
C5
3
10
u
C5
9
10
uC
14
10
u
C3
8
0.0
47
u
C1
15
CK
73
FB
B1
H1
54
K0
.15
uC
11
3
22u
C421
22
uC
41
7
CK
73
FX
R1
E4
75
K4
.7u
C6
0
4.7
u
C5
2 25
4.7
uC
64
10u
C439
100pC619
16
33
0uC
2
16
33
0uC
3
25
47
u
C4
25
47
0uC1
254
70
uC
5
CS
77
AB
E1
D1
00
M2
01
0u
C1
14
CN
3
10
9
8
7
6
5
4
3
2
1
13
12
11
10
9
8
7
6
5
4
3
2
1
20
19
18
17
16
15
14
13
12
11
10987654321
E40-6862-05CN2
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
987654321
EC720AA-0560ACN1
RB521CM-30
D401
D26
RB521CM-30
D14
RB520SM-30D24
RB
52
0S
M-3
0D
21
L8104
D206
RB521CM-30D27
RN
14
2S
D2
02
RB521CM-30D18
RB521CM-30
D602
RN
14
2S
D2
08
RN
14
2S
D2
09
RB521CM-30
D619
RB521CM-30D408
RB521CM-30
D409
RB521CM-30D19
L8104D205
RB
52
1C
M-3
0D
41
0
1S
S4
00
SM
D1
5
RB
06
0M
-40
D1
6
1S
S4
00
SM
D1
07
RB521CM-30
D610
RB521CM-30
D609
RB561VM-40D17
1S
S3
90
D3
01
1S
S3
90
D3
02
L8
10
4
D2
07
RB520SM-30D618
RB
52
1C
M-3
0
D6
15
1S
S4
00
SM
D3
03
1S
S4
00
SM
D3
04
RB521CM-30D614
ED
ZV
6.8
B
D6
11
ED
ZV
18
BD
20
EDZV5.6BD13
ED
ZV
6.8
B
D6
08
ED
ZV
6.8
B
D6
07
ED
ZV
6.8
B
D6
06
ED
ZV
6.8
B
D6
05
ED
ZV
5.6
B
D2
01
ED
ZV
6.8
B
D6
04
ED
ZV
6.8
B
D6
03
ED
ZV
8.2
BD
10
1
EDZV8.2B
D407
EDZV8.2BD22
ED
ZV
5.6
B
D6
01
$D
20
3
SM
V1
27
0-0
79
LF
D1
02
1SV282-FD103
1S
V2
82
-FD
10
51
SV
28
2-F
D1
06
SM
V1
13
0-0
79
LF
D1
08
1SV282-FD104
DA
20
4U
D6
12
RB
70
6F
-40
D2
04
DA
20
4U
D6
13
ST
70
-27
F-5
72
D1
F1B-0085-00E101
F1B-0085-00E11
FZA10BS-5R0F4
F53-0286-05
F2
F5
3-0
28
6-0
5
F1
F53-0286-05
F3
F53-0286-05
F6
FZA10BS-5R0F5
2
1
109
58
37
64L4
15
2
1
109
58
37
64
L7
9-1
98
4-0
5L
41
9
2
1
109
58
37
64L4
16
CE3 VSS 2
VIN4 VoUT 1
XC6221D501G-GIC26
Vo
UT
3
GN
D
2
VIN
4
Co
NT
Ro
L
1
NJM
28
78
F4
-32
IC1
7
STBY
3GND2
VIN
4VoUT1
BU31TD2WNVXIC13
CE3 VSS 2
VIN4 VoUT 1
XC6221D501G-GIC609
Vo
UT
3
VS
S
2
VIN
4
CE
1XC
62
15
B1
22
N-G
IC1
5
VoUT
3EN2
GND
4VIN1
LXDC2HN18F163IC12
CE
3 VSS 2
VIN4 VoUT 1
XC8102AA07-GIC21
NC
3
VIN
2
VS
S
4
VO
UT
1
XC
61
CN
50
02
N-G
IC1
8
CE
3 VSS 2
VIN
4 VoUT 1
XC6221D501G-GIC23
CE3 VSS 2
VIN4 VoUT 1
XC6223D321G-GIC19
NC
3VIN2
VSS
4VOUT1
XC61CN5002N-GIC413
RF
_o
UT
4
VD
D
3
VG
G
2
RF
_IN
1
RA60H1317A501IC201
Vo
UT
5
VIN
4
CE
3
VS
S
2
NC
1XC
62
09
B5
02
P-G
IC1
6
VCC
5
oUTY
4 GND 3
INA
2
INB
1
TC7SZ08FEIC408
VCC 5
oUTY
4GND3
INA2
G1
TC7SET125FUFIC606
VCC 5
oUTY
4GND3
INA2
G1
TC7SET125FUF
IC407
Vo
UT
5
VIN
4
CE
3
VS
S
2
NC
1XC
62
23
D3
21
P-G
IC2
0
VCC5
oUTY4 GND 3
INA 2
INB 1
TC7SZ08FE
IC403
AD
J
5
Vo
UT
4
GN
D
3
VC
C
2
CT
L
1
BA00DD0WHFPIC1
VCTL1
6
PC
5
VCTL2
4P23
GND2
P11
NJG1608KB2IC301
SW
6
NC
5
FB
4EN3
VIN2
GND1
TPS61041DRVRIC14
CUR_ADJ
6
ENABLE
5
RF_OUT
4RF_IN3
NC2
VCC1
BGU6104IC202
VPoS
8
VAPC
7
NC
6
CoMM
5FLTR4
VSET3
ENBL2
RFIN1
AD8315ARMIC205
VCC8
oUT27
-IN26
+IN25
VEE
4
+IN1
3
-IN1
2
oUT1
1
BA3472FVMIC203
VCC
8
G2
7
Y1
6
A2
5GND4
Y23
A12
G11
TC7WT126FU-F
IC602
VCC
8
G2
7
Y1
6
A2 5
GND
4
Y2
3
A12
G11
TC7WH126FKIC603
VDD
8
oUT2
7
IN2-
6
IN2+
5VSS4
IN1+3
IN1-2
oUT11
BU7462NUXIC414
V+8
BoUTPUT7
B-INPUT6
B+INPUT5
V-
4
A+INPUT
3
A-INPUT
2
AoUTPUT
1
$IC204
V+
8
Bo
UT
PU
T
7
B-I
NP
UT
6
B+
INP
UT
5
V-
4
A+
INP
UT
3
A-I
NP
UT
2
Ao
UT
PU
T
1
NJM
29
04
CR
B1
IC1
01
VDD
8
oUT2
7
IN2-
6
IN2+
5VSS4
IN1+3
IN1-2
oUT11
BU7462NUX
IC608
GN
D_
3
9
GN
D_
2
8
EN7
VIN_2
6
VIN_1
5GND_1
4VoUT_2 3
VoUT_1 2MoDE 1
LXDC2XQ12A-252IC24
VCC
10
S9
D+8
D-7
oE6
GND
5
2D-
4
2D+
3
1D-
2
1D+
1
BD11600NUXIC405
SCLK
10
SYNC9
DIN8
VREFIN7
GND6
VoUTD
5
VoUTC
4
VoUTB 3
VoUTA
2
VA
1
DAC124S085CISIC411
VCC
10
S9
D+8
D-7
oE6
GND
5
2D-
4
2D+
3
1D-
2
1D+
1
BD11600NUXIC406
EXPOSED11
BS
T
10
VIN
_2
9
VIN
_1
8
FR
EQ
7
GN
D
6
FB
5
Co
MP
4
EN
3
SW
_2
2
SW
_1
1
IC25
oU
T1
12
NC
2
11
PW
RG
ND
10
NC
1
9
oU
T2
8
VC
C
7
PP
6
ST
BY
5
IN2
4
PR
EG
ND
3
IN1
2
RF
1
LA4631VC-XEIC601
VCC
16
GND
15
R2IN
8
T1oUT
14
R1IN
13
R1oUT
12
T1IN
11
T2IN
10
R2oUT9
T2oUT
7
V-
6
C2-
5
C2+
4
C1-
3
V+
2
C1+
1
ADM3202ARUZ
IC605
DVSS
20
19
10
18
17
16
15
14
13
12
11
98
76
54
32
DVCC1
MSP430G2533P0
IC22
Vo
UT
2
24
Vo
UT
12
3
VIN
12
2
VIN
82
1
Vo
UT
82
0V
oU
T7
19
VIN7 18
GND 17
RESET 16
VDAREF2 15
VDAREF1
14
VIN6
13
Vo
UT
6
12
Vo
UT
51
1
VIN
51
0
VIN
49
Vo
UT
48
Vo
UT
37
VIN36
DI5
CLK4
LD3
VDD2
VIN21
R2A20178NPIC412
EX
PA
D25
A2
24
A1
23
INT
22
VC
C
21
SD
A
20
SC
L
19
A018
P1717
P1616
P1515
P1414
P1313
P1
2
12P
11
11
P1
0
10
GN
D
9
P0
7
8
P0
6
7
P05 6
P04 5
P03 4
P02 3
P01 2
P00 1
TCA9555RTWRIC409
EXPAD
25
A224
A123
INT22
VCC21
SDA20
SCL19
A0
18
P1
71
7
P1
61
6
P1
51
5
P1
41
4
P1
31
3
P12 12
P11 11
P10 10
GND 9
P07 8
P06 7
P0
56
P0
45
P0
34
P0
23
P0
12
P0
01
TCA9555RTWRIC604
+VA232
REFP31
REFM30
GPIo29
+VBD28
BDGND27
SDo26
SDI25
SC
LK
24
CS
23
AG
ND
2
22
+V
A1
21
CH
0
20
CH
1
19
CH
2
18
CH
3
17
CH4 16
CH5 15
CH6 14
CH7 13
CH8 12
CH9 11
CH10 10
CH11 9
CH
12
8
CH
13
7
CH
14
6
CH
15
5
AIN
M
4
AIN
P
3
MX
o
2
AG
ND
1
1
ADS7961SRHBIC410
DV
DD
32
RE
SE
T3
1
RIG
HT
_L
oM
30
RIG
HT
_L
oP
29
LE
FT
_L
oM
28
LE
FT
_L
oP
27
AV
SS
22
6A
VD
D
25
DRVDD2
24
HPRoUT
23
HPRCoM 22
DRVSS 21
HPLCoM 20
HPLoUT 19
DRVDD1 18
AVSS1 17
MIC
2R
/LIN
E2
R
16
MIC
BIA
S
15
MIC
2L
/LIN
E2
L/M
ICD
ET
14
MIC
1R
M/L
INE
1R
M1
3
MIC
1R
P/L
INE
1R
P1
2
MIC
1L
M/L
INE
1L
M1
1
MIC
1L
P/L
INE
1L
P1
0S
DA
9
SCL8
IoVDD7
DVSS6
DoUT5
DIN4
WCLK3
BCLK2
MCLK1
TLV32AIC3104IIC607
VSS4
53
DA_FS52
AD_FS51
AD_SDo50
AD_SCLK49
DVDD48
LD47
SDATAo46
SCLK45
SDATAI44
CSN43
AGC_KEEP42
TX_PDN41
RX_PDN40
RS
TN
39
VC
oM
_A
D
38
AD
VD
D
37
AD
VS
S
36
TE
ST
2
35
Ao
UT
_N
34
Ao
UT
_P
33
RX
VD
D
32
BIA
S1
31
LN
AV
DD
30
LN
AC
oN
T
29
LN
AIN
28
VS
S3
27
VSS2 26
LNAoUT 25
DEMVDD 24
DEMIN 23
VSS1 22
LoVDD 21
RFoUTN 20
RFoUTP 19
LoIN 18
LoDVDD 17
CPZ 16
SWIN 15
CP 14
CP
VD
D
13
SY
NV
DD
12
SY
NV
SS
11
VR
EF
2
10
TC
Xo
IN
9
VR
EF
1
8
DA
CV
DD
7
SM
Fo
UT
6
BIA
S2
5T
ES
T1
4D
A_
SD
I3
DV
SS
2
DA
_S
CL
K
1
IC302
VSSQ5 E1
VSSQ1 D9
VSSQ4 C1
VSSQ3 B9
VSSQ2 A3
VSS3 K1
VSS2 F1
VSS1 A1
VDDQ5E9
VDDQ4D1
VDDQ3C9
VDDQ2B1
VDDQ1A7
VDD3K9
VDD2F9
VDD1A9
A1
2
H3
NC
1
F7
NC
2
F3
UD
QS
E2
LD
QS
E8
DQ
15
A2
DQ
14
B3
DQ
13
B2
DQ
12
C3
DQ
11
C2
DQ
10
D3
DQ
9
D2
DQ
8
E3
DQ
7
E7
DQ
6
D8
DQ
5
D7
DQ
4
C8
DQ
3
C7
DQ
2
B8
DQ
1
B7
DQ
0
A8
UD
M
F2
LD
M
F8
WE
G7
CA
S
G8
RA
S
G9
BA
1
H9
BA
0
H8
CS
H7
CK
E
G1
CK
G2
CK
G3
A1
1
H2
A1
0/A
P
J7
A9
H1
A8
J3
A7
J2
A6
J1
A5
K3
A4
K2
A3
K8
A2
K7
A1
J9
A0
J8
IC402
VSS1E8VSS2
H2VSS3
H7
VCCG5
NC
1
A1
NC
2
A8
RF
U1
B1
RF
U2
C1
RF
U3
D1
NC
3
H1
NC
4
H8
RY
/BY
A4
RF
U4
E1
BY
TE
F7
RF
U5
G1
DQ
15
/A-1
G7
DQ
14
F6
DQ
13
G6
DQ
12
F5
DQ
11
G4
DQ
10
F4
DQ
9
G3
DQ
8
F3
DQ
7
E6
DQ
6
H6
DQ
5
E5
DQ
4
H5
DQ
3
H4
DQ
2
E4
DQ
1
H3
DQ
0
E3
VIo
2
D8
VIo
1
F1
WP
/AC
C
B4
RE
SE
T
B5
WE
A5
oE
G2
CE
F2
A2
5
G8
A2
4
F8
A2
3
C8
A2
2
B8
A2
1
C5
A2
0
D4
A1
9
D5
A1
8
C4
A1
7
B3
A1
6
E7
A1
5
D7
A1
4
C7
A1
3
A7
A1
2
B7
A1
1
D6
A1
0
C6
A9
A6
A8
B6
A7
A3
A6
C3
A5
D3
A4
B2
A3
A2
A2
C2
A1
D2
A0
E2
IC401
DVDD3318_C10
R4
DVDD3318_C9
P12
DVDD3318_C8
P6
DVDD3318_C7
P5
DVDD3318_C6
N13
DVDD3318_C5
M13
DVDD3318_C4L13
DVDD3318_C3L4
DVDD3318_C2K13
DVDD3318_C1J5
DVDD3318_B11K15
DVDD3318_B10J14
DVDD3318_B9G9
DVDD3318_B8F13
DVDD3318_B7F12
DVDD3318_B6F11
DVDD3318_B5F10
DVDD3318_B4F8
DVDD3318_B3F7
DVDD3318_B2F6
DVDD3318_B1E14
DVDD3318_A6H5
DVDD3318_A5G15
DVDD3318_A4G14
DVDD3318_A3G5
DVDD3318_A2F15
DVDD3318_A1F5
DV
DD
18
_1
0
R13
DV
DD
18
_9
P13
DV
DD
18
_8
L6
DV
DD
18
_7
K5
DV
DD
18
_6
J13
DV
DD
18
_5
G12
DV
DD
18
_4
G11
DV
DD
18
_3
G10
DV
DD
18
_2
G6
DV
DD
18
_1
F14
RV
DD
3
N7
RV
DD
2
H14
RV
DD
1
E5
CV
DD
18
N8
CV
DD
17
M9
CV
DD
16
M8
CV
DD
15
L12
CV
DD
14
K12
CV
DD
13
K6
CV
DD
12
J12
CV
DD
11
J6
CV
DD
10
H13
CV
DD
9
H12
CV
DD
8
H11
CV
DD
7
H10
CV
DD
6
H7
CV
DD
5
H6
CV
DD
4
G13
CV
DD
3
G8
CV
DD
2
G7
CV
DD
1
E15
NC3
M3
RSV2
T19
SATA_VDD4
N4
SATA_VDD3
P2
SATA_VDD2
P1
SATA_VDD1 M2
SATA_VDDR P3
USB_CVDDM12
USB1_VDDA18 P14
USB1_VDDA33 P15
USB0_VDDA18 N14
USB0_VDDA33 N18
DDR_DVDD18_10 R9
DDR_DVDD18_9 R8
DDR_DVDD18_8 R7
DDR_DVDD18_7 P10
DDR_DVDD18_6 P9
DDR_DVDD18_5 P8
DDR_DVDD18_4 P7
DDR_DVDD18_3 N10
DDR_DVDD18_2 N9
DDR_DVDD18_1 N6
DDR_VREF
R6
DDR_ZP
U12
RTC_CVDD
L14
PLL1_VDDA
N15
PLL0_VDDA
L15
VS
S3
0
P11
VS
S2
9
N12
VS
S2
8
N11
VS
S2
7
N5
VS
S2
6
M11
VS
S2
5
M10
VS
S2
4
M7
VS
S2
3
M6
VS
S2
2
M5
VS
S2
1
M4
VS
S2
0
L11
VS
S1
9
L10
VS
S1
8
L9
VS
S1
7
L8
VS
S1
6
L7
VS
S1
5
L5
VS
S1
4
K11
VS
S1
3
K10
VS
S1
2
K9
VS
S1
1
K8
VS
S1
0
K7
VS
S9
J11
VS
S8
J10
VS
S7
J9
VS
S6
J8
VS
S5
J7
VS
S4
H15
VS
S3
H9
VS
S2
H8
VS
S1
A19
NC
2
N16
NC
1
M14
SA
TA
_V
SS
6
M1
SA
TA
_V
SS
5
L3
SA
TA
_V
SS
4
K2
SA
TA
_V
SS
3
K1
SA
TA
_V
SS
2
H2
SA
TA
_V
SS
1
H1
RT
C_
VS
S
H18
PL
L1
_V
SS
A
M15
PL
L0
_V
SS
A
M17
oS
CV
SS
L18
PRU1_R30<0>/PRU1_R31<1>
K4
MMCSD1_DAT<1>/PRU1_R30<1>/PRU1_R31<2>
J3
MMCSD1_DAT<2>/PRU1_R30<2>/PRU1_R31<3>
K3
MMCSD1_DAT<3>/PRU1_R30<3>/PRU1_R31<4>
H3
RMII_CRS_DV/PRU1_R31<29>
W19
RMII_MHZ_50_CLK/PRU0_R31<23>
W18
RMII_RXER/PRU0_R31<24>W17
RMII_RXD<0>/PRU0_R31<25>V17
RMII_RXD<1>/PRU0_R31<26>W16
RMII_TXEN/PRU0_R31<27>R14
RMII_TXD<0>/PRU0_R31<28>V16
RMII_TXD<1>/PRU0_R31<29>U18
GP6<5>P17
PRU0_R30<9>/PRU0_R31<9>R15
PRU0_R30<10>/PRU0_R31<10>R19
PRU0_R30<11>/PRU0_R31<11>R18
PRU0_R30<12>/PRU0_R31<12>T16
PRU0_R30<13>/PRU0_R31<13>U19
PRU0_R30<14>/PRU0_R31<14>V19
PRU0_R30<15>/PRU0_R31<15>V18
GP6<6>V15
GP6<7>W14
SATA_REGN3
SATA_REFCLKNN1
SATA_REFCLKPN2
SATA_TXNJ2
SATA_TXPJ1
SATA_RXNL2
SATA_RXPL1
LCD_AC_ENB_CSR5
MMCSD1_DAT<4>/LCD_VSYNCG4
MMCSD1_DAT<5>/LCD_HSYNCH4
MMCSD1_DAT<6>/LCD_MCLKF2
MMCSD1_DAT<7>/LCD_PCLKF1
MMCSD0_CLKE9
USB1_DPP19
USB1_DMP18
USB0_VDDA12N17
USB0_DRVVBUSK18
USB0_VBUSN19
USB0_IDP16
USB0_DPM19
USB0_DMM18
RTC_ALARM/DEEPSLEEPF4
RTC_XoH19
RTC_XIJ19
oSCoUTK19
oSCINL19
CLKoUTT18
RTCK/GP8<0>K17
EMU1K16
EMU0J16
TRSTL17
TCKJ15
TDoJ18
TDIM16
TMS
L16
RESEToUT
T17
NMI
J17
RESET
K14
LC
D_D
<0>
W1
LC
D_D
<1>
W2
LC
D_D
<2>
W3
LC
D_D
<3>
V1
LC
D_D
<4>
V2
LC
D_D
<5>
V3
LC
D_D
<6>
U1
LC
D_D
<7>
U2
LC
D_D
<8>
/BooT
<0>
U3
LC
D_D
<9>
/BooT
<1>
T1
LC
D_D
<10>
/BooT
<2>
T2
LC
D_D
<11>
/BooT
<3>
T3
LC
D_D
<12>
/BooT
<4>
R1
LC
D_D
<13>
/BooT
<5>
R2
LC
D_D
<14>
/BooT
<6>
R3
LC
D_D
<15>
/BooT
<7>
P4
DD
R_D
QG
AT
E1
R12
DD
R_D
QG
AT
E0
R11
DD
R_B
A<
0>
V8
DD
R_B
A<
1>
T9
DD
R_B
A<
2>
U8
DD
R_D
QS
<1>
V11
DD
R_D
QS
<0>
T14
DD
R_D
QM
<1>
R10
DD
R_D
QM
<0>
W13
DD
R_C
S
V9
DD
R_C
AS
U9
DD
R_R
AS
W9
DD
R_W
E
T8
DD
R_C
KE
V7
DD
R_C
LK
N
W7
DD
R_C
LK
P
W8
DD
R_A
<0>
U7
DD
R_A
<1>
T7
DD
R_A
<2>
W6
DD
R_A
<3>
V6
DD
R_A
<4>
U5
DD
R_A
<5>
V5
DD
R_A
<6>
W5
DD
R_A
<7>
U6
DD
R_A
<8>
U4
DD
R_A
<9>
T6
DD
R_A
<10>
W4
DD
R_A
<11>
T4
DD
R_A
<12>
V4
DD
R_A
<13>
T5
DD
R_D
<0>
U15
DD
R_D
<1>
U14
DD
R_D
<2>
V14
DD
R_D
<3>
U13
DD
R_D
<4>
V13D
DR
_D
<5>
V12D
DR
_D
<6>
W12
DD
R_D
<7>
W11
DD
R_D
<8>
T13
DD
R_D
<9>
T11
DD
R_D
<10>
T10
DD
R_D
<11>
T12
DD
R_D
<12>
U10
DD
R_D
<13>
V10
DD
R_D
<14>
U11
DD
R_D
<15>
W10
AMUTE/UART2_RTS D5
AFSR C2
ACLKR A1
AHCLKR/UART1_RTS A2
AFSX B2
ACLKX B1
AHCLKX/USB_REFCLKIN/UART1_CTS A3
AXR0/ECAP0_APWM0/MII_TXD<0>/CLKS0 F3
AXR1/DX0/MII_TXD<1> E1
AXR2/DR0/MII_TXD<2> E2
AXR3/FSX0/MII_TXD<3> E3
AXR4/FSR0/MII_CoL D1
AXR5/CLKX0/MII_TXCLK D3
AXR6/CLKR0/MII_TXEN C1
AXR7 D2
AXR8/CLKS1/ECAP1_APWM1 E4
AXR9/DX1 C3
AXR10/DR1 D4
AXR11/FSX1 C5
AXR12/FSR1 C4
AXR13/CLKX1 B3AXR14/CLKR1 B4
AXR15/ECAP2_APWM2A4
GP8<12> G3
MMCSD1_CMD J4
MMCSD1_CLK G2
MMCSD1_DAT<0> G1
GP6<8> T15
GP6<9> U16
GP6<10> W15
GP6<11> U17
GP6<12> R16
GP6<13> R17
SPI1_SoMI H17
SPI1_SIMo G17
SPI1_SCS<7>/I2C0_SCL
G16
SPI1_SCS<6>/I2C0_SDA
G18
SPI1_SCS<5>/UART2_RXD
F17
SPI1_SCS<4>/UART2_TXD
F16
SPI1_SCS<3>/UART1_RXD
E18
SPI1_SCS<2>/UART1_TXD
F19
SPI1_SCS<1>F18
SPI1_SCS<0>E19
SPI1_ENA H16
SPI1_CLK G19
SPI0_SoMI/MII_RXER C16
SPI0_SIMo/MII_CRS C18
SPI0_SCS<5>/UART0_RXD/MII_RXD<3> C19
SPI0_SCS<4>/UART0_TXD/MII_RXD<2>
D18
SPI0_SCS<3>/UART0_CTS/MII_RXD<1>
E17
SPI0_SCS<2>/UART0_RTS/MII_RXD<0>
D16
SPI0_SCS<1>/MDIo_CLK
E16
SPI0_SCS<0>/MDIo_D
D17
SPI0_ENA/MII_RXDV
C17
SPI0_CLK/MII_RXCLK
D19
EM
A_
WA
IT<
1>
B19
EM
A_
WA
IT<
0>
B18
EM
A_
oE
B15
EM
A_
WE
N_
DQ
M<
0>
C8
EM
A_
WE
N_
DQ
M<
1>
A5
EM
A_
WE
B9
EM
A_
A_
RW
D10
EM
A_
CS
<5
>
B16
EM
A_
CS
<4
>
F9
EM
A_
CS
<3
>
A17
EM
A_
CS
<2
>
B17
EM
A_
CS
<0
>
A18
EM
A_
CA
S
A9
EM
A_
RA
S
A16
EM
A_
SD
CK
E
D8
EM
A_
CL
K
B7
EM
A_
BA
<1
>
A15
EM
A_
BA
<0
>
C15
EM
A_
A<
0>
C14
EM
A_
A<
1>
D15
EM
A_
A<
2>
B14
EM
A_
A<
3>
D14
EM
A_
A<
4>
A14
EM
A_
A<
5>
C13
EM
A_
A<
6>
E13
EM
A_
A<
7>
B13
EM
A_
A<
8>
A13
EM
A_
A<
9>
D12
EM
A_
A<
10
>
C12
EM
A_
A<
11
>
B12
EM
A_
A<
12
>
D13
EM
A_
A<
13
>
D11
EM
A_
A<
14
>/M
MC
SD
0_
DA
T<
7>
A12
EM
A_
A<
15
>/M
MC
SD
0_
DA
T<
6>
C11
EM
A_
A<
16
>/M
MC
SD
0_
DA
T<
5>
E12
EM
A_
A<
17
>/M
MC
SD
0_
DA
T<
4>
B11
EM
A_
A<
18
>/M
MC
SD
0_
DA
T<
3>
E11
EM
A_
A<
19
>/M
MC
SD
0_
DA
T<
2>
C10
EM
A_
A<
20
>/M
MC
SD
0_
DA
T<
1>
A11
EM
A_
A<
21
>/M
MC
SD
0_
DA
T<
0>
B10
EM
A_
A<
22
>/M
MC
SD
0_
CM
D
A10
EM
A_
D<
0>
C9
EM
A_
D<
1>
A8
EM
A_
D<
2>
B8
EM
A_
D<
3>
E8
EM
A_
D<
4>
B5
EM
A_
D<
5>
E7
EM
A_
D<
6>
C6
EM
A_
D<
7>
D7
EM
A_
D<
8>
E10
EM
A_
D<
9>
D9
EM
A_
D<
10
>
A7
EM
A_
D<
11
>
D6
EM
A_
D<
12
>
A6
EM
A_
D<
13
>
B6
EM
A_
D<
14
>
C7
EM
A_
D<
15
>
E6
IC404
E1B-0001-00J2
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
E58-0567-05J1
LK
73
H0
AM
R1
0J
10
0n
L3
12
(-53)
27
0n
L2
10
LK73H0AM33NJ33n
L317
$L
30
1
L4
1-2
78
5-5
32
70
nL
11
3
LK73H0AMR10J
100nL302
LK73H0AM27NJ27n
L123
L4
1-2
78
5-5
3
27
0n
L1
12
LK73H0AM27NJ27n
L121
LR
79
G0
CQ
47
NG
47
nL304
LR
79
G0
CQ
56
NG
56
nL
31
3
$L316
L4
1-2
78
5-5
32
70
nL
11
6
10
0n
L3
15
LR
79
G0
CQ
R3
3G
33
0n
L3
11
L4
1-2
78
5-5
32
70
nL
11
1L
41
-27
85
-53
27
0n
L1
10
LR
79
G0
CQ
82
NG
82
nL
31
0
LR79G0CQ82NG
82nL305
LR
79
G0
CQ
R2
2G
22
0n
L3
07
LR
79
G0
CQ
R1
2G
12
0n
L3
08
(-5
3)
27
nL2
22
(-53)
82
nL2
14
LR
79
G0
CQ
68
NG
68
nL
30
9LK
73
H0
AM
R2
7J
27
0n
L3
14
LK
73
H0
AM
56
NJ
56
nL
12
4
LR79Z0GJR56G560nL224
LR79G0CQ8N2C
8.2nL306
LR
79
G0
CQ
56
NG
56
nL
30
3
LK
73
H0
AM
47
NJ
47
nL
11
8
LK
73
H0
AM
47
NJ
47
nL
21
3
(-7
1)
56
nL2
09
LK73H0AM56NJ
56n
L211 LK73H0AM56NJ56n
L212
L41-2785-53270n
L108
L41-2785-53
270n
L115
LR
77Z
0A
AR
27J
27
0n
L2
23
(-39)4.7u
L404
LB73G0AK-001
L413
LB
73
G0
AK
-00
1
L4
03
L411
LB73G0AM-004L13
LB73G0AM-004
L405
LB73G0AM-004L15
LB
73
G0
BA
-00
4L
21
8
LB73H0AY-004L225
LB73H0AV-002L414
LB73H0AV-002L17
LB
73
H0
AV
-00
3L
22
6
LB
73
H0
AV
-00
3
L2
17
LB73H0AV-003L402
LB73G0AK-001
L16
LB73H0AV-003L107
LB73H0AV-003
L602
LB73H0AV-003
L601
LB
73
H0
AY
-00
4
L2
07
LB
73
H0
AY
-00
4L
11
7
LB
73
Z0
AF
-00
1
L2
19
LB
73
G0
AK
-00
1
L4
01
LB
73
Z0
AF
-00
1
L2
21
LB
73
H0
AY
-00
2
L4
18
L410
LB73G0AK-001
L412
LB
73
G0
AK
-00
1L
11
LB
73
F0
AW
-00
2
L2
15
L92-1101-05L420
LB73H0AV-003L109
LB
73
H0
AY
-00
2
L4
17
LB
73
H0
AY
-00
4L
20
8
LB73H0AV-003L603
LB
73
G0
AK
-00
1
L1
9
LB73H0AV-002L18
L92-1101-05
L409
L408
L406
L407
LB73H0AY-004L119
LB
73
Z0
AF
-00
1L
22
0
$L
21
6
LR79Z0AA150M
15uL14
5TL34-4903-05
L2
5T
L3
E-0
01
8-0
0L
5
5TL34-4903-05
L4
9.5
TL
34
-49
02
-05
L1
5TL34-4903-05
L3
9.5
T
L3
4-4
84
8-0
5
L6
L34-4610-1535.5n
L7
Q1072SC5108FT/Y/
$Q203
Q202LSCR523EBFS8
Q204LSCR523EBFS8
Q1062SC5108FT/Y/
Q4012SC4617/S/
Q1042SD2654/W/
Q15LSCR523EBFS8
Q16LSAR523UBFS8
Q1
05
MC
H3
91
4-H
/8/
Q402SSM3K15AMFV
Q4
03
SS
M3
K1
5A
MF
V
Q301SSM3K15AMFV
Q201RFM01U7PF
Q20SSM3J334R
Q606SSM3J334R
Q22SSM3J334R
LTC014EEBFS8Q13
LTC014EEBFS8Q23
LTC014EEBFS8Q18
LTC014EEBFS8Q11
LTC014EEBFS8
Q21
LTC014TEBFS8
Q14
LT
C0
14
TE
BF
S8
Q4
04
LTC014TEBFS8Q604
LTC014TEBFS8Q602
SSM6N15AFEM
Q605
SSM6N15AFEMQ601
VT
6M
1Q
20
6
EM6M2Q103VT6M1
Q19
EMD9Q205
EMD9
Q25
TP
CP
81
07
-FQ
60
3
TPCP8107-F
Q17
TPCP8107-FQ12
0
R116
0
R437
0
R504
100
R658
0
R6
74
0R
11
7
0
R663
33
R145
0
R5
31
0
R5
4
0
R42
0R532
0
R139
0
R2
4
0R131
0
R434
10
R4
28
10R68
10R660
10
R4
23
10R422
10
0R
49
6
100
R43
15
0R
14
3
10
0R
49
7
100
R48
$R263
10
0R
49
5
10
0R
49
4
1k
R664
1k
R668
1k
R2
71
$R
10
2
1k
R500
2.2
k
R4
41
$R521
1k
R6
62
1k
R6
91
k
R5
03
10
k
R5
25
2.2
k
R4
40
1k
R420
22
R425
1k
R219
1kR212
2.2
k
R4
39
1kR676
1k
R112
1k
R1
13
10k
R498
10k
R29
$R
41
9
12
0k
R5
6
10
k
R7
1
10kR507
$R415
$R
23
2
10
k
R2
7
10kR47
10k
R124
10k
R247
10
k
R4
4
10kR508
1k
R267
10
k
R7
3
10
0k
R3
3
$R405
10
0k
R6
61
10
0k
R1
36
10
0k
R1
22
10
0k
R2
1
$R404
10
0k
R5
0
10
0k
R1
28 $R
23
7
10MR125
12
0
R2
20
1.2
k
R1
32
120kR115
15
0
R1
20
10
k
R2
51
$R
21
0
15
k
R4
26
$R
20
1
27
kR
28
2
18
k
R2
73
22R218
22
R4
24
39
R216
27
0
R2
14
27
0
R2
17
2.2
k
R2
30
2.2k
R231
2.2
kR
11
9
2.2
kR
62
4.7
k
R5
17
4.7
kR
51
4
1k
R241
$R253
22
k
R5
13
22
k
R2
45
22
k
R5
12
22
k
R2
59
22
k
R2
75
22kR41
$R
23
4
22
kR
24
4
22
k
R1
14
$R
40
3
22
k
R2
74
270k
R266
$R
23
6
22
k
R2
35
$R
25
5
22
k
R6
7
$R1
12
0k
R2
60
10
0k
R2
50
22
0k
R4
9
18
0
R1
09
27
0
R2
48
18
0
R2
25
18
0
R2
22
18
0
R1
08
(D)27k
R672
330
R75
330
R526
33
k
R4
27
$R
26
4
33k
R511
39
k
R5
18
33
0k
R6
6
56
R224
56
R223
39
R215
3.3
k
R2
27
5.6
k
R1
40
47
R1
27
470
R261
$R
25
7
47
R2
38
27
R2
26
0
R118
47
0
R7
7
$R254
4.7
kR
12
1
4.7
k
R7
4
5.6k
R228
4.7
k
R7
2
47k
R229
47
k
R1
34
47
k
R6
71
47
k
R3
1
47
k
R5
05
47k
R133
47
0k
R2
11
68
0
R6
73
68
0
R4
29
6.8
k
R6
75
68
k
R6
66
$R
43
0
8.2
kR
22
1
(D)10k
R61
(D)150k
R59
(D)11k
R46
10
0k
R2
31
00
kR
22
(D)100kR506
10
0k
R2
5 (D)
1.5
k
R8
3
(D)
22
k
R5
30
(D)
22
kR
53
3
(D)
22
k
R5
29
22
kR
26
(D)22kR534
(D)
27
k
R7
0
(D)47k
R45
RK73HH1J391D390
R123
(D)
4.7
kR8
4
(D)11k
R60
1kR486
1k
R55
1k
R3
5
1kR485
1k
R462
$R401
1k
R38
1k
R2
8
1k
R488
10
kR
39
10kR34
10k
R435
1M
R4
36
10
0k
R3
6
100k
R431
10
0k
R3
0
100k
R51
100k
R432
10
0k
R5
2
10
0k
R5
7
22
R491
22
R459
22
R452
22
R44422
R458
22
R466
22
R469
22
R472
22
R442
22
R475
22
R448
22
R450
22
R482
22
R457
22
R445
22
R480
22
R463
22
R454
22
R487
22
R447
22
R455
22
R481
22
R493
22
R474
22
R453
22
R490
22
R461
22
R451
22
R478
22
R443
22
R479
22
R456
22
R492
22
R460
22
R473
22
R476
22
R449
22
R484
22
R477
22
R464
22
R465
22
R471
22
R467
22
R446
22
R470
22
R468
4.7
k
R4
33
4.7
kR
37
47
k
R4
0
47kR53
47k
R76
56
R2
771/2
W
56
R2
76
2.2k
R648
100R638
100R639
49.9R483
22
0
R2
56
100R624
$R
24
9
12
0
R2
33
39
R243
39
R240
$R
25
2
$R246
27
0
R2
39
27
0
R2
42
18
0
R2
05
RN
73
HH
1J1
51
D
15
0
R1
37
RN73HH1J100D10
R138
$R209
120
R272
0
R2
80
0
R2
70
0
R32
10
0R
26
2
220R207
3.3
R8
2
3.3k
R78
3.3k
R79
3.3k
R80
2.7
R8
1
0
R206
120
R269
10R65R92-3769-05
10
R64
18
0
R1
42
0
R421
0R208
100R637
2.2k
R649
22k
R654
22k
R655
1k
R6
44
6.8
k
R6
53
6.8
k
R6
47
0
R627
100
R325
$R107
0R613
$R612
0R659
$R601
(D)30kR58
11
k
R6
3
2.2
k
R4
38
47
0R
48
9
10
k
R2
13
0
R2
78
$R602$R603
0
R304
$R402
47
0
R3
15
$R607
12
R314
10
0k
R6
77
470
R626
RK
73
HH
1J4
73
D
47
kR
31
7
1kR656
1kR657
$R
20
2
0
R416
10
k
R6
17
1k
R4
18
22
k
R3
07
0
R203
0
R2
04
10
k
R5
09
10
kR
13
5
10
k
R1
41
47
R3
09
0
R1
44
22k
R310
18
0
R3
05
0
R665
(D)
27
k
R3
19
18
0
R3
08
5.6
R312
0R
52
8
82
0
R3
03
$R417
10
R322
22k
R652
0R
32
6
82
0
R3
02
56
R279
100kR535
$R
41
4
$R
41
3
100k
R502
10R323
10R324
10
0k
R5
01
10
kR
49
9
0R
40
7
$R
40
6
0R
40
8
1k
R320
$R
40
9100k
R527
3.3
k
R5
24
(D)
27
0R
31
1
0
R321
3.3
k
R5
23
3.3
k
R5
22
0R
52
0
0R
51
6
0R
51
9
22k
R646
$R
41
1
$R
41
2
12k
R667
68
0
R6
69
0
R641
15
0
R1
48
4.7
k
R1
478.2
kR
14
6
22
R1
49
10
R536
10
R537
10
k
R6
19
33
0R
67
9
33
0R
67
0
10
0k
R6
22
33
0R
67
8
33
0R
68
0
100
R538
0R
53
9
$R
54
0
$R
54
1
47
k
R6
42
1.5k
R681
$R11
$R4
$R3
10
k
R6
16
$R12
47
0k
R3
16
$R13
47
0
R3
13
$R14
10
0k
R6
18
470R640
$R
61
1
0R631
0
R6
25
0
R614
1k
R6
45
0
R6
50
$R606
$R
61
0
$R
60
4
0
R6
51
$R
60
9
470R636
0
R634
0R633
$R
60
5
0
R628
$R
60
8
0
R6
23
4.7k
R629
R2
10
k
R6
15
$R15
4.7
k
R6
21
0
R630
47k
R632
100R635
$R16
4.7
k
R6
20
22k
R265
10k
R643
100*4CP409
RK74HB1J100JCP302
4.7k*4
CP602
10*4
CP
40
5
10*4
CP
40
3
10*4
CP604
10*4
CP
40
4
100*4CP411
10
0*4
CP
40
6
100*4CP408
10
0*4
CP
40
7
RK74HB1J100JCP303
47*4
CP
41
347*4
CP
41
447*4
CP
41
2
4.7k*4
CP601
100*4
CP605
100*4
CP410
2.2k
CP402
10
k*4
CP
40
1
RK74HB1J100J
CP301
NC
U1
5W
F1
04
F6
ST
H2
03
-t
10
0k
NC
U1
5W
F10
4F
6S
TH
20
1
-t
10
0k
NC
U1
5W
F1
04
F6
S
TH
20
2
-t
10
0k
TH
40
1
-t
CN31
CN30
CN29CN93CN92CN28
CN
49
CN23CN24
CN22
CN
47
CN
46
CN
45
CN
44
CN
38
CN
42
CN
43
CN
41
CN
40
CN32
CN
39
CN
37
CN90
CN98
CN97
CN96
CN50
CN80CN75
CN74
CN78
CN76
CN91
CN77CN82
CN
83
CN81
CN
35
CN95
CN
48
CN89
CN25
CN87
CN
15
CN68
CN16
CN67
CN
14
CN
58
CN79
CN
60
CN
11
CN
21
CN18
CN61
CN
17
CN
13
CN55
CN
12
CN88
CN
59
CN20
CN27CN26
CN19
CN
52
CN
34
CN33
CN
53
CN
65
CN
70
CN71
CN
62
CN86
CN
69
CN72
CN
63
CN
64
CN94
CN
36
CN
51 C
N5
4
CN56
CN
66
CN
57
CN
85
AV
RM
10
27
0K
10
1
D6
17
D404
D405
SP
C1
05
01
A0
1 D406
SP
C1
05
01
A0
1
D402
D403
AVRM10270K101D616
VCC
oUTGND
VC
L7H-0076-00X401
L77-1802-05X402
SCHEMATIC DIAGRAM TX-RX UNIT (XC1-182K-00 (NX-3720H(G), NX-3720H, NX-3720(G), NX-3720))
A
1
B C D E F G
2
3
4
5
6
7
8
9
10
H I J K L M N O P Q(No.RA054<Rev.001>) 2-15
PWR
R1
Destination
R3
R2
R4
$R1
$R11
*R4
*R3
$R12
$R13
$R14
R2
$R15
$R16
F2
F1
0
R4
-
R3
-
0
(F2:400-470)
K-01
(F1:450-520)
K-00
13.6V
+B$C
71
$C
70
100p
C26
470p
C22
25
1000u
C1
ST
70-2
7F
-572
D1
F53-0
286-0
5
F1
SBWTDIOSBWTCK
0
R24
CN
15
CN
14
CN
11
CN
21
CN
13
CN
12
$CN10
2200pC29
13
12
11
10
9
8
7
6
5
4
3
2
1
330
R7547k
R76
P_TXD2
/OVRB
P_RXD2
1u
C76
0.1
uC
16
10u
C14
D26
100k
R30
RB521CM-30
RB
520S
M-3
0D
21
100k
R23
R22
R25
22k
R26
100k
100k
P2.3
P2.4
P2.5
P1.6
P1.7
SBWTDlo
SBWTCK
P2.7
P2.6
P2.2
P2.1
P2.0
P1.5
A4
A3
TXD
RXD
P1.0DVSS
20
19
10
18
17
16
15
14
13
12
11
98
76
54
32
DVCC1
MSP430G2533P0
IC22
/BINT2
/PSW_OUT
/BINT
/OVRB_OUT
PWR_CNT
100k
R33
10kR34
CN
17
BAT_CNT
/IGN
/IGN_OUT
/PSW
RB521CM-30D27
3.1V
5.0V
12BU
31BUBATT CHK
50BU
31BU
0.1
uC
11
RB520SM-30D24
EDZV5.6BD13
Q15LSCR523EBFS8
Q16LSAR523UBFS8
47k
R31
0
R32
CN16
0.0
47u
C75
0.1
uC
74
1u
C18 0.4
7u
C17
STBY
3GND2
VIN
4VoUT1
BU31TD2WNVXIC13
1.2V32M
1u
C24
1u
C31
CN
3
VoU
T
3
VS
S
2
VIN
4
CE
1XC
6215B
122N
-GIC
15
1k
R28
13.6V
/OVRB(For MSP430)
SB1(HEAD/AFamp)
470p
C20
1u
C28
470pC21
1000p
C25
ED
ZV
18B
D20
FZA10BS-5R0F4
LTC014EEBFS8Q13
LTC014EEBFS8Q11
EMD9
Q25
TPCP8107-FQ12
10k
R29
10k
R27
470
R77
CN18
IGN
1000p
C27
0.0
1u
C19
0.1
uC
15
RB521CM-30D18
RB521CM-30D19
EDZV8.2BD22
NC
3
VIN
2
VS
S
4
VO
UT
1
XC
61C
N5002N
-G
IC18
LTC014TEBFS8Q14
100k
R21
3.3k
R78
3.3k
R79
3.3k
R80
19.2MHz
32M
FCNT
OSCGNDB
0.01u
C438
0.0
1u
C436
100p
C433
10
R423
1k
R420
22
R425
15k
R426
22
R424
0
R421
VCC
oUTGND
VC
L7H-0076-00X401
TEMP
0.0
1u
C418
LB73H0AV-003L402
100k
TH
401
-t
NC
U15W
F104F
6S
0.01u
C447
1u
C462
0.0
1u
C450
5p
C454
100p
C445
(-39)4.7u
L404
Q4012SC4617/S/
10
R428
33k
R427
680
R429
$R
430
For RVDD,USBFor CVDD
12M
_1
12M
_1
0.1
uC
428
0.1
uC
441
0.1
uC
434
0.1
uC
444
0.1
uC
443
0.1
uC
431
0.1
uC
424
22u
C421
10u
C439
For DVDD IO For DVDD IO For USB
32M
_1
32M
_1
32M
_1
0.1
uC
425
0.1
uC
429
0.1
uC
448
0.1
uC
451
0.1
uC
442
0.1
uC
440
10u
C437
10u
C446
10u
C422
For DDR_DVDD
For DVDD IO
18M
_1
18M
_2
0.1
uC
471
0.1
uC
470
0.1
uC
469
0.1
uC
468
0.1
uC
463
0.1
uC
466
0.1
uC
464
0.1
uC
455
0.1
uC
461
0.1
uC
457
0.1
uC
458
0.1
uC
459
0.1
uC
467
0.1
uC
465
0.1
uC
460
10u
C452
10u
C456
10u
C453
10u
C449
1.8V
12BU
18M
12M
LB
73G
0A
K-0
01
L403
0.1
uC
419
0.1
uC
427
0.1
uC
420
0.1
uC
430
0.1
uC
432
0.1
uC
435
0.1
uC
426
0.1
uC
423
22u
C4
17
18M
DD
RM
_B
A[1
]
DD
RM
_D
QM
[0]
DD
RM
_A
[0]
DD
RM
_A
[12]
DD
RM
_A
[6]
DD
RM
_A
[9]
DD
RM
_D
[9]
DD
RM
_D
QS
[1]
DD
RM
_D
[13]
DD
RM
_B
A[0
]
DD
RM
_A
[2]
DD
RM
_A
[1]
DD
RM
_A
[13]
DD
RM
_C
KE
DD
RM
_C
LK
P
DD
RM
_A
[10]
DD
RM
_C
AS
DD
RM
_D
[3]
DD
RM
_D
[10]
DD
RM
_A
[8]
DD
RM
_D
[15]
DD
RM
_R
AS
DD
RM
_A
[4]
DD
RM
_D
[11]
DD
RM
_D
QM
[1]
DD
RM
_D
[8]
DD
RM
_D
[2]
DD
RM
_D
[5]
DD
RM
_A
[3]
DD
RM
_C
LK
N
DD
RM
_D
[6]
DD
RM
_D
[1]
DD
RM
_A
[7]
DD
RM
_W
E
DD
RM
_A
[5]
DD
RM
_D
[7]
DD
RM
_D
[14]
DD
RM
_A
[11]
DD
RM
_D
[4]
DD
RM
_D
[12]
DD
RM
_D
QS
[0]
DD
RM
_D
[0]
DD
RM
_C
S
VSSQ5 E1
VSSQ1 D9
VSSQ4 C1
VSSQ3 B9
VSSQ2 A3
VSS3 K1
VSS2 F1
VSS1 A1
VDDQ5E9
VDDQ4D1
VDDQ3C9
VDDQ2B1
VDDQ1A7
VDD3K9
VDD2F9
VDD1A9
A12
H3
NC
1
F7
NC
2
F3
UD
QS
E2
LD
QS
E8
DQ
15
A2
DQ
14
B3
DQ
13
B2
DQ
12
C3
DQ
11
C2
DQ
10
D3
DQ
9
D2
DQ
8
E3
DQ
7
E7
DQ
6
D8
DQ
5
D7
DQ
4
C8
DQ
3
C7
DQ
2
B8
DQ
1
B7
DQ
0
A8
UD
M
F2
LD
M
F8
WE
G7
CA
S
G8
RA
S
G9
BA
1
H9
BA
0
H8
CS
H7
CK
E
G1
CK
G2
CK
G3
A11
H2
A10/A
P
J7
A9
H1
A8
J3
A7
J2
A6
J1
A5
K3
A4
K2
A3
K8
A2
K7
A1
J9
A0
J8
IC402
FlashROM 512Mb
/FRST = OPEN DRAIN
/WP internal Pull-Up
18M_1
DA
TA
[0]
18M_3
DA
TA
[15]
/CS
2
AD
D[1
9]
AD
D[1
4]
DA
TA
[12]
AD
D[1
6]
DA
TA
[1]
AD
D[1
7]
DA
TA
[7]
AD
D[2
1]
AD
D[0
]
AD
D[7
]
32M
DA
TA
[10]
DA
TA
[13]
/WR
DA
TA
[9]
/WP
AD
D[1
1]
AD
D[1
3]
DA
TA
[14]
DA
TA
[6]
AD
D[8
]
AD
D[1
]
AD
D[2
0]
DA
TA
[2]
AD
D[2
]
/CS
_F
AD
D[3
]
DA
TA
[4]
DA
TA
[11]
DA
TA
[5]
AD
D[9
]
DA
TA
[8]
AD
D[2
3]
AD
D[6
]
AD
D[1
8]
AD
D[5
]
AD
D[2
2]
AD
D[1
5]
/OE
AD
D[1
2]
/FR
ST
AD
D[4
]
AD
D[1
0]
DA
TA
[3]
1u
C478
1u
C414 0.1
uC
415
0.1
uC
477
0.1
uC
476
0.1
uC
416
RB521CM-30
D401
VSS1E8VSS2
H2VSS3
H7
VCCG5
NC
1
A1
NC
2
A8
RF
U1
B1
RF
U2
C1
RF
U3
D1
NC
3
H1
NC
4
H8
RY
/BY
A4
RF
U4
E1
BY
TE
F7
RF
U5
G1
DQ
15
/A-1
G7
DQ
14
F6
DQ
13
G6
DQ
12
F5
DQ
11
G4
DQ
10
F4
DQ
9
G3
DQ
8
F3
DQ
7
E6
DQ
6
H6
DQ
5
E5
DQ
4
H5
DQ
3
H4
DQ
2
E4
DQ
1
H3
DQ
0
E3
VIo
2
D8
VIo
1
F1
WP
/AC
C
B4
RE
SE
T
B5
WE
A5
oE
G2
CE
F2
A25
G8
A24
F8
A23
C8
A22
B8
A21
C5
A20
D4
A19
D5
A18
C4
A17
B3
A16
E7
A15
D7
A14
C7
A13
A7
A12
B7
A11
D6
A10
C6
A9
A6
A8
B6
A7
A3
A6
C3
A5
D3
A4
B2
A3
A2
A2
C2
A1
D2
A0
E2
IC401
LB
73G
0A
K-0
01
L401
100k
R431
100k
R432
4.7
k
R433
CN
83
CN
52
CN
53
CN
51 C
N54
/CS
3
1.8V
/FR
ST
/WP
/CS
_F
/CS
2
0.1uC479
VCC5
oUTY4 GND 3
INA 2
INB 1
TC7SZ08FE
IC403
LB73G0AK-001
L413
/FLDMLOW = UART OR USB LOADER
AD
D[6
]
GP
SB
T_D
ET
BT
_S
W
/FLD
M
/OE
/CS
2
/CS
4
AS
TS
W
/CS
3
AD
D[9
]
AD
D[1
0]
AD
D[7
]
AD
D[2
]
AD
D[8
]
AD
D[4
]
AD
D[3
]
AD
D[1
1]
/WR
AD
D[0
]
AD
D[1
]
AD
D[5
]
1k
R462CN68
CN67
CN
85
/CS2/CS3
DA
TA
[9]
DA
TA
[4]
DA
TA
[6]
AD
D[1
5]
AD
D[1
8]
DA
TA
[15]
DA
TA
[10]
DA
TA
[8]
DA
TA
[11]
DA
TA
[12]
DA
TA
[7]
AD
D[1
6]
AD
D[1
9]
DA
TA
[13]
AD
D[1
4]
DA
TA
[1]
AD
D[1
7]
AD
D[1
3]
DA
TA
[3]
AD
D[2
2]
AD
D[2
1]
AD
D[2
0]
AD
D[1
2]
AD
D[2
3]
DA
TA
[14]
DA
TA
[0]
DA
TA
[2]
DA
TA
[5]
19.2M32k_I
32k_O
USB0_DPUSB0_DM RTCGNDG
15pC481
18pC480$C401 0
R437
1M
R436
CN55
L77-1802-05X402
CTS2
UMode
50A
0
R434
0.1
u
C482
0.22uC483
CN56
SYMTIM_IN
/DCR_RST
DM_OUT
DM_IN
ASSW
PWR_CNT
GPS_ANT_SW
AGCKEEP
32M
/INT_IO 10k
R435
CN98
CN86
TDI
TDO
/TRST
TMS
TCK$C
N9
19.2M
/RST
MCLK10
9
8
7
6
5
4
3
2
1
10R422
BE
R_E
N
/PS
W_O
UT
/IG
N_O
UT
PA
_M
UT
E
/BIN
T2
PLD
SB
C
/OV
RB
_O
UT
10k*4
CP
401
BO
OT
[2]
BO
OT
[3]
BO
OT
[0]
BO
OT
[7]
BO
OT
[6]
BO
OT
[5]
BO
OT
[1]
BO
OT
[4]
12BU_1
18M_2
18M_1
32M_1
PLL1_VDDA
12M_1
PLL0_VDDA
32M_1
18M_1
32M_1
12
M_
1
12M_1
18
M_
1
OSCGNDB
PLL0GNDE
PLL1GNDFRTCGNDG
0.1uC485
0.1
uC
48
6DVDD3318_C10
R4
DVDD3318_C9
P12
DVDD3318_C8
P6
DVDD3318_C7
P5
DVDD3318_C6
N13
DVDD3318_C5
M13
DVDD3318_C4L13
DVDD3318_C3L4
DVDD3318_C2K13
DVDD3318_C1J5
DVDD3318_B11K15
DVDD3318_B10J14
DVDD3318_B9G9
DVDD3318_B8F13
DVDD3318_B7F12
DVDD3318_B6F11
DVDD3318_B5F10
DVDD3318_B4F8
DVDD3318_B3F7
DVDD3318_B2F6
DVDD3318_B1E14
DVDD3318_A6H5
DVDD3318_A5G15
DVDD3318_A4G14
DVDD3318_A3G5
DVDD3318_A2F15
DVDD3318_A1F5
DV
DD
18
_1
0
R13
DV
DD
18
_9
P13
DV
DD
18
_8
L6
DV
DD
18
_7
K5
DV
DD
18
_6
J13
DV
DD
18
_5
G12
DV
DD
18
_4
G11
DV
DD
18
_3
G10
DV
DD
18
_2
G6
DV
DD
18
_1
F14
RV
DD
3
N7
RV
DD
2
H14
RV
DD
1
E5
CV
DD
18
N8
CV
DD
17
M9
CV
DD
16
M8
CV
DD
15
L12
CV
DD
14
K12
CV
DD
13
K6
CV
DD
12
J12
CV
DD
11
J6
CV
DD
10
H13
CV
DD
9
H12
CV
DD
8
H11
CV
DD
7
H10
CV
DD
6
H7
CV
DD
5
H6
CV
DD
4
G13
CV
DD
3
G8
CV
DD
2
G7
CV
DD
1
E15
NC3
M3
RSV2
T19
SATA_VDD4
N4
SATA_VDD3
P2
SATA_VDD2
P1
SATA_VDD1 M2
SATA_VDDR P3
USB_CVDDM12
USB1_VDDA18 P14
USB1_VDDA33 P15
USB0_VDDA18 N14
USB0_VDDA33 N18
DDR_DVDD18_10 R9
DDR_DVDD18_9 R8
DDR_DVDD18_8 R7
DDR_DVDD18_7 P10
DDR_DVDD18_6 P9
DDR_DVDD18_5 P8
DDR_DVDD18_4 P7
DDR_DVDD18_3 N10
DDR_DVDD18_2 N9
DDR_DVDD18_1 N6
DDR_VREF
R6
DDR_ZP
U12
RTC_CVDD
L14
PLL1_VDDA
N15
PLL0_VDDA
L15
VS
S3
0
P11
VS
S2
9
N12
VS
S2
8
N11
VS
S2
7
N5
VS
S2
6
M11
VS
S2
5
M10
VS
S2
4
M7
VS
S2
3
M6
VS
S2
2
M5
VS
S2
1
M4
VS
S2
0
L11
VS
S1
9
L10
VS
S1
8
L9
VS
S1
7
L8
VS
S1
6
L7
VS
S1
5
L5
VS
S1
4
K11
VS
S1
3
K10
VS
S1
2
K9
VS
S1
1
K8
VS
S1
0
K7
VS
S9
J11
VS
S8
J10
VS
S7
J9
VS
S6
J8
VS
S5
J7
VS
S4
H15
VS
S3
H9
VS
S2
H8
VS
S1
A19
NC
2
N16
NC
1
M14
SA
TA
_V
SS
6
M1
SA
TA
_V
SS
5
L3
SA
TA
_V
SS
4
K2
SA
TA
_V
SS
3
K1
SA
TA
_V
SS
2
H2
SA
TA
_V
SS
1
H1
RT
C_
VS
S
H18
PL
L1
_V
SS
A
M15
PL
L0
_V
SS
A
M17
oS
CV
SS
L18
PRU1_R30<0>/PRU1_R31<1>
K4
MMCSD1_DAT<1>/PRU1_R30<1>/PRU1_R31<2>
J3
MMCSD1_DAT<2>/PRU1_R30<2>/PRU1_R31<3>
K3
MMCSD1_DAT<3>/PRU1_R30<3>/PRU1_R31<4>
H3
RMII_CRS_DV/PRU1_R31<29>
W19
RMII_MHZ_50_CLK/PRU0_R31<23>
W18
RMII_RXER/PRU0_R31<24>W17
RMII_RXD<0>/PRU0_R31<25>V17
RMII_RXD<1>/PRU0_R31<26>W16
RMII_TXEN/PRU0_R31<27>R14
RMII_TXD<0>/PRU0_R31<28>V16
RMII_TXD<1>/PRU0_R31<29>U18
GP6<5>P17
PRU0_R30<9>/PRU0_R31<9>R15
PRU0_R30<10>/PRU0_R31<10>R19
PRU0_R30<11>/PRU0_R31<11>R18
PRU0_R30<12>/PRU0_R31<12>T16
PRU0_R30<13>/PRU0_R31<13>U19
PRU0_R30<14>/PRU0_R31<14>V19
PRU0_R30<15>/PRU0_R31<15>V18
GP6<6>V15
GP6<7>W14
SATA_REGN3
SATA_REFCLKNN1
SATA_REFCLKPN2
SATA_TXNJ2
SATA_TXPJ1
SATA_RXNL2
SATA_RXPL1
LCD_AC_ENB_CSR5
MMCSD1_DAT<4>/LCD_VSYNCG4
MMCSD1_DAT<5>/LCD_HSYNCH4
MMCSD1_DAT<6>/LCD_MCLKF2
MMCSD1_DAT<7>/LCD_PCLKF1
MMCSD0_CLKE9
USB1_DPP19
USB1_DMP18
USB0_VDDA12N17
USB0_DRVVBUSK18
USB0_VBUSN19
USB0_IDP16
USB0_DPM19
USB0_DMM18
RTC_ALARM/DEEPSLEEPF4
RTC_XoH19
RTC_XIJ19
oSCoUTK19
oSCINL19
CLKoUTT18
RTCK/GP8<0>K17
EMU1K16
EMU0J16
TRSTL17
TCKJ15
TDoJ18
TDIM16
TMS
L16
RESEToUT
T17
NMI
J17
RESET
K14
LC
D_D
<0>
W1
LC
D_D
<1>
W2
LC
D_D
<2>
W3
LC
D_D
<3>
V1
LC
D_D
<4>
V2
LC
D_D
<5>
V3
LC
D_D
<6>
U1
LC
D_D
<7>
U2
LC
D_D
<8>
/BooT
<0>
U3
LC
D_D
<9>
/BooT
<1>
T1
LC
D_D
<10>
/BooT
<2>
T2
LC
D_D
<11>
/BooT
<3>
T3
LC
D_D
<12>
/BooT
<4>
R1
LC
D_D
<13>
/BooT
<5>
R2
LC
D_D
<14>
/BooT
<6>
R3
LC
D_D
<15>
/BooT
<7>
P4
DD
R_D
QG
AT
E1
R12
DD
R_D
QG
AT
E0
R11
DD
R_B
A<
0>
V8
DD
R_B
A<
1>
T9
DD
R_B
A<
2>
U8
DD
R_D
QS
<1>
V11
DD
R_D
QS
<0>
T14
DD
R_D
QM
<1>
R10
DD
R_D
QM
<0>
W13
DD
R_C
S
V9
DD
R_C
AS
U9
DD
R_R
AS
W9
DD
R_W
E
T8
DD
R_C
KE
V7
DD
R_C
LK
N
W7
DD
R_C
LK
P
W8
DD
R_A
<0>
U7
DD
R_A
<1>
T7
DD
R_A
<2>
W6
DD
R_A
<3>
V6
DD
R_A
<4>
U5
DD
R_A
<5>
V5
DD
R_A
<6>
W5
DD
R_A
<7>
U6
DD
R_A
<8>
U4
DD
R_A
<9>
T6
DD
R_A
<10>
W4
DD
R_A
<11>
T4
DD
R_A
<12>
V4
DD
R_A
<13>
T5
DD
R_D
<0>
U15
DD
R_D
<1>
U14
DD
R_D
<2>
V14D
DR
_D
<3>
U13
DD
R_D
<4>
V13
DD
R_D
<5>
V12
DD
R_D
<6>
W12
DD
R_D
<7>
W11
DD
R_D
<8>
T13
DD
R_D
<9>
T11
DD
R_D
<10>
T10
DD
R_D
<11>
T12
DD
R_D
<12>
U10
DD
R_D
<13>
V10
DD
R_D
<14>
U11
DD
R_D
<15>
W10
AMUTE/UART2_RTS D5
AFSR C2
ACLKR A1
AHCLKR/UART1_RTS A2
AFSX B2
ACLKX B1
AHCLKX/USB_REFCLKIN/UART1_CTS A3
AXR0/ECAP0_APWM0/MII_TXD<0>/CLKS0 F3
AXR1/DX0/MII_TXD<1> E1
AXR2/DR0/MII_TXD<2> E2
AXR3/FSX0/MII_TXD<3> E3
AXR4/FSR0/MII_CoL D1
AXR5/CLKX0/MII_TXCLK D3
AXR6/CLKR0/MII_TXEN C1
AXR7 D2
AXR8/CLKS1/ECAP1_APWM1 E4
AXR9/DX1 C3
AXR10/DR1 D4
AXR11/FSX1 C5
AXR12/FSR1 C4
AXR13/CLKX1 B3AXR14/CLKR1 B4
AXR15/ECAP2_APWM2A4
GP8<12> G3
MMCSD1_CMD J4
MMCSD1_CLK G2
MMCSD1_DAT<0> G1
GP6<8> T15
GP6<9> U16
GP6<10> W15
GP6<11> U17
GP6<12> R16
GP6<13> R17
SPI1_SoMI H17
SPI1_SIMo G17
SPI1_SCS<7>/I2C0_SCL
G16
SPI1_SCS<6>/I2C0_SDA
G18
SPI1_SCS<5>/UART2_RXD
F17
SPI1_SCS<4>/UART2_TXD
F16
SPI1_SCS<3>/UART1_RXD
E18
SPI1_SCS<2>/UART1_TXD
F19
SPI1_SCS<1>F18
SPI1_SCS<0>E19
SPI1_ENA H16
SPI1_CLK G19
SPI0_SoMI/MII_RXER C16
SPI0_SIMo/MII_CRS C18
SPI0_SCS<5>/UART0_RXD/MII_RXD<3> C19
SPI0_SCS<4>/UART0_TXD/MII_RXD<2>
D18
SPI0_SCS<3>/UART0_CTS/MII_RXD<1>
E17
SPI0_SCS<2>/UART0_RTS/MII_RXD<0>
D16
SPI0_SCS<1>/MDIo_CLK
E16
SPI0_SCS<0>/MDIo_D
D17
SPI0_ENA/MII_RXDV
C17
SPI0_CLK/MII_RXCLK
D19
EM
A_
WA
IT<
1>
B19
EM
A_
WA
IT<
0>
B18
EM
A_
oE
B15
EM
A_
WE
N_
DQ
M<
0>
C8
EM
A_
WE
N_
DQ
M<
1>
A5
EM
A_
WE
B9
EM
A_
A_
RW
D10
EM
A_
CS
<5
>
B16
EM
A_
CS
<4
>
F9
EM
A_
CS
<3
>
A17
EM
A_
CS
<2
>
B17
EM
A_
CS
<0
>
A18
EM
A_
CA
S
A9
EM
A_
RA
S
A16
EM
A_
SD
CK
E
D8
EM
A_
CL
K
B7
EM
A_
BA
<1
>
A15
EM
A_
BA
<0
>
C15
EM
A_
A<
0>
C14
EM
A_
A<
1>
D15
EM
A_
A<
2>
B14
EM
A_
A<
3>
D14
EM
A_
A<
4>
A14
EM
A_
A<
5>
C13
EM
A_
A<
6>
E13
EM
A_
A<
7>
B13
EM
A_
A<
8>
A13
EM
A_
A<
9>
D12
EM
A_
A<
10
>
C12
EM
A_
A<
11
>
B12
EM
A_
A<
12
>
D13
EM
A_
A<
13
>
D11
EM
A_
A<
14
>/M
MC
SD
0_
DA
T<
7>
A12
EM
A_
A<
15
>/M
MC
SD
0_
DA
T<
6>
C11
EM
A_
A<
16
>/M
MC
SD
0_
DA
T<
5>
E12
EM
A_
A<
17
>/M
MC
SD
0_
DA
T<
4>
B11
EM
A_
A<
18
>/M
MC
SD
0_
DA
T<
3>
E11
EM
A_
A<
19
>/M
MC
SD
0_
DA
T<
2>
C10
EM
A_
A<
20
>/M
MC
SD
0_
DA
T<
1>
A11
EM
A_
A<
21
>/M
MC
SD
0_
DA
T<
0>
B10
EM
A_
A<
22
>/M
MC
SD
0_
CM
D
A10
EM
A_
D<
0>
C9
EM
A_
D<
1>
A8
EM
A_
D<
2>
B8
EM
A_
D<
3>
E8
EM
A_
D<
4>
B5
EM
A_
D<
5>
E7
EM
A_
D<
6>
C6
EM
A_
D<
7>
D7
EM
A_
D<
8>
E10
EM
A_
D<
9>
D9
EM
A_
D<
10
>
A7
EM
A_
D<
11
>
D6
EM
A_
D<
12
>
A6
EM
A_
D<
13
>
B6
EM
A_
D<
14
>
C7
EM
A_
D<
15
>
E6
IC404
1kR486
1kR485
49.9R483
3.2V
1.8V
1.8V18M_1
32M_1
18M_2L411
L410
LB73G0AK-001
L412
1.2V
1.2V
1.2V
1.2V
12BU_1
PLL1_VDDA
12M_1
PLL0_VDDA
PLL0GNDE
PLL1GNDF
RTCGNDG
0.1
uC
490
0.1
u
C4
74
0.1
u
C475
0.1
u
C4
72
0.1
u
C473
LB73G0AM-004
L405
L92-1101-05L420
L92-1101-05
L409
L408
L406
L407
32M
18M
22
R444
CN61 BOOT PIN
Emulation Debug BOOT = 00011110
For Production line
UART BOOT=10010111
CN941 CN922 CN923 CN924 CN925
PLL_CLK
2.2
k
R441
2.2
k
R440
2.2
k
R439
2.2
kR
438
CN
58
CN
60
CN
59
CN
65
CN
62
CN
63
CN
64
CN
66
CN
57
2.2k
CP402
32M
50A
DC
R_A
CLK
DC
R_D
DO
/DC
R_D
CS
/DC
R_A
CS
DC
R_A
DI
BC
LK
PLD
DC
R_D
ID
CR
_D
O/D
CR
_C
S
AG
CK
EE
PT
XR
X
/DC
R_R
ST
50C
0.1uC336
100pC33510
R322
RK74HB1J100J
CP301
CN
47
CN
46
CN
45
CN
44
CN
43
CP
VC
O_M
OD
CP
Z
50C
100p
C332
0.1uC330
100pC329
0.1uC3280.4
7u
C345
10u
C344
10u
C346
100p
C343
470p
C338
1u
C327
0
R304
(D)
27k
R319
0R
326
AK2401
VSS4
53
DA_FS52
AD_FS51
AD_SDo50
AD_SCLK49
DVDD48
LD47
SDATAo46
SCLK45
SDATAI44
CSN43
AGC_KEEP42
TX_PDN41
RX_PDN40
RS
TN
39
VC
oM
_A
D
38
AD
VD
D
37
AD
VS
S
36
TE
ST
2
35
AoU
T_N
34
AoU
T_P
33
RX
VD
D
32
BIA
S1
31
LN
AV
DD
30
LN
AC
oN
T
29
LN
AIN
28
VS
S3
27
VSS2 26
LNAoUT 25
DEMVDD 24
DEMIN 23
VSS1 22
LoVDD 21
RFoUTN 20
RFoUTP 19
LoIN 18
LoDVDD 17
CPZ 16
SWIN 15
CP 14
CP
VD
D
13
SY
NV
DD
12
SY
NV
SS
11
VR
EF
2
10
TC
XoIN
9
VR
EF
1
8
DA
CV
DD
7
SM
FoU
T
6
BIA
S2
5
TE
ST
1
4
DA
_S
DI
3D
VS
S2
DA
_S
CLK
1
IC302
LR
79G
0C
Q39N
G
39n
L307 R
311
RK
73H
H1J391D
390
100pC326
$C348
0.1
uC
347
100pC325
2p
C307
$C
301
3p
C334
15p
C333
$C
302
$C
303
100p
33n
L312
$L301
LK73H0AM33NJ
33nL302
LK
73H
0A
MR
27J
270n
L314
150
R325
100
R305
100
R308
0.01uC324
C323
470p
C306
5.6
R312
820
R303
820
R302
470p
C341
LR79G0CQ22NG
22nL305
LR79G0CQ3N9C
3.9nL3064p
C312
RK
73H
H1J473D
47k
R317
CN
49
CN
48
470pC313
0.01uC314
1u
C315
3.2V
10u
C321
100p
C322
2.2
u
C342 1u
C316
0.1u
C340
1u
C73
0
R321
470k
R316
32C
50C
SB
C
SBC
1u
C72
CE3 VSS 2
VIN4 VoUT 1
XC6223D321G-GIC19
LB73H0AV-002L18
10R323
10R324
1k
R320
RK74HB1J100JCP302
RK74HB1J100JCP303
CN
38
CN
42
CN
41
CN
40
CN
39
CN
37
CN
35
CN
34
CN
36
SB2(9Vreg/D-sub)
31BU
/OVRB
SB1
BLVL
SB2
SBC
+B
/IGN
1000p
C56
1000p
C47
1S
S400S
M
D15
100k
R50
2.2
kR
62
220k
R49
CN20
5.0V50C54M
470p
C39
2.2
u
C4650
1uC41
CE
3 VSS 2
VIN
4 VoUT 1
XC6221D501G-GIC23
0
R42
13.6V
470pC42
470p
C36
FZA10BS-5R0F5
LTC014EEBFS8Q18
TPCP8107-F
Q17
10kR47
10k
R44
3.2V
32A
470p
C51
16
1u
C43
50
1u
C33
50
1uC
50
VoU
T
3
GN
D
2
VIN
4
CoN
TR
oL
1
NJM
2878F
4-3
2IC
17
LB73H0AV-002L17
0
R54
1k
R38
5.0V
18M SWLoad Switch
50A
32A12BU
50A
2.2
u
C55
CE3 VSS 2
VIN4 VoUT 1
XC6221D501G-GIC26
3.2V
1.8V
/RST
18M_3
32M
0.1
u
C49 CE
3 VSS 2
VIN
4 VoUT 1
XC8102AA07-GIC21
47kR53
32M
100p
C504
0.1
u
C35
2.2
u
C44
50
1u
C37
RB521CM-30
D14V
oU
T
5
VIN
4
CE
3
VS
S
2
NC
1XC
6223D
321P
-GIC
20
LB73G0AK-001
L16
10k
R39
4.7
kR
37
100
R538
1.2V
12M
10u
C40
10u
C38
4.7
u
C52
GN
D_3
9
GN
D_2
8
EN7
VIN_2
6VIN_1
5
GND_1
4
VoUT_2 3
VoUT_1 2
MoDE 1
LXDC2XQ12A-252IC24
LB
73G
0A
K-0
01
L11
LB
73G
0A
K-0
01
L19
VT6M1
Q19
100
R48
1k
R55
1k
R35
100k
R36
100k
R51
100k
R52
100k
R57
47k
R40
1.8V
18M
12M
18M
10u
C57
VoUT
3EN2
GND
4VIN1
LXDC2HN18F163IC12
50
4.7
uC
30
50
4.7
uC
34
50
4.7
uC
32
MP2560DQ-LF-Z
54M
EXPOSED11
BS
T
10
VIN
_2
9
VIN
_1
8
FR
EQ
7
GN
D
6
FB
5
CoM
P
4
EN
3
SW
_2
2
SW
_1
1
IC25
(D)10k
R61
(D)150k
R59
(D)11k
R46
(D)47k
R45
(D)11k
R60
(D)30kR58
25
0.1
uC45
LB73G0AM-004L15
5.4V10uL12
100p
C48
$C
1316
10u
C541
610u
C53
RB
060M
-40
D16
LB73G0AM-004L13
120k
R56
11k
R63
BA
T_C
NT
100
R43
22kR41
CN19
54M DC/DC SHIELD CASE
+B
54M
F1B-0085-00E11
4p
C101
*L118
*C137
47p
C138
150
R143
VCO Buffer
$C
106
470p
C134
9p
C131
7p
C133
9p
C132
2p
C128 0.5
pC
129
0.5pC135
100p
C136
220pC127
SM
V1130-0
79LF
D108
L41-2
785-5
3270n
L113 L41-2
785-5
3270n
L116
L41-2785-53
270n
L115
LB
73H
0A
Y-0
04
L117
L34-4610-1535.5n
L7
Q1062SC5108FT/Y/
Q105
MC
H3914-H
/8/ 0
R139
100k
R136
1.8
k
R140
RN
73H
H1J151D
150
R137
RN73HH1J100D10
R138
56
R142
2.7
kR
141
VCO
CPZ
CP
$C
149
470p
C124
100p
C120
220pC123
0.0
47u
C115
CK
73F
BB
1H
154K
0.1
5u
C113
CS
77A
BE
1D
100M
20
10u
C114 SM
V1270-0
79LF
D102
1SV282-FD103
1S
V282-F
D105
1S
V282-F
D106
1SV282-FD104
L41-2
785-5
3
270n
L112
L41-2
785-5
3270n
L111
L41-2
785-5
3
270n
L110
L41-2785-53270n
L108
LB73H0AV-003L107
LB73H0AV-003L109
0
R116
0R131
10k
R124
220
R1200
R118
RK73HH1J391D390
R123
Tripler
4.2V
VCO Buffer/BPF SHIELD CASE
*C102*C121
47p
C105
*C103
*C126
47p
C119
100p
C117
*C122
F1B-0085-00E101
*L103
*L105
*L101
*L106
Q1012SC5108FT/Y/Q102
2SC5108FT/Y/
$R
101
22
R111
*R146*R110
22
R147
*R1063.9
kR
103 1.8
k
R104
*R105
1.8
k
R1293.9
kR
126
*R130
270
R214
270
R217
15pC216
15pC218
5p
C217
2p
C201
5p
C219
(-71)15n
L209 22R218
39
R216
39
R215
Pre-Drive
470p
C220
0.0
47u
C221
100p
C223
CUR_ADJ
6
ENABLE
5
RF_OUT
4RF_IN3
NC2
VCC1
BGU6104IC202
1k
R219
TX:5.0VRX:0V
4700p
C222
470p
C224
120
R220
8.2
kR
221
470pC225
5p
C226
5p
C228
10p
C227
8p
C230
22p
C229LK73H0AM8N2J
8.2n
L213
15n
L211LK73H0AM15NJ
15n
L212
270
R225
270
R222
39
R224
39
R223
47
R226
Drive
Q201RFM01U7PF
470p
C233
4p
C234
(-53)
*L214
LB
73F
0A
W-0
02
L215
150
R233
2pC274
470pC238
(-53)
*L216
$C
273
$R
24939
R24339
R240
$R
252
270
R239
270
R242
470pC241
LB
73G
0B
A-0
04
L218
LB
73Z
0A
F-0
01
L219
LB
73Z
0A
F-0
01
L221
LB
73Z
0A
F-0
01
L220
TX Low power:3.7VTX High power:4.2V
Gate
Bia
s 2
Gate
Bia
s 1
+B
$C
215
$R246
0
R280
470p
C245
100p
C244
22p
C242
47p
C243 2
5470u
C5
27p
C250
(-53)
47nL222
390
R256
*R262
$R
206
56
R268
56
R281
$R
205
100p
C249
100p
C247
RF
_oU
T
4
VD
D
3
VG
G
2
RF
_IN
1
CN27CN26
F2:RA60H3847-501
F1:RA60H4452-501
*IC201
27p
C256
*C253
$R207
*R269
*L223
*R272
$C205
$C
206
470pC254
RB
706F
-40
D204
$R209
0
R270
TX:1.6VRX:0V
470p
C257
470p
C255
56
R2771/2
W
56
R276
*C2079.5
T
L34-4
848-0
5
L6
470p
C258
*C259
L8104
D205
L8104D206
LR79G0GK82NG
82n
L224
C93-1932-05
100pC262
1.5
TL34-4
743-0
5L5
TX:0.9VRX:0V
RX
4p
C261
RN
142S
D209
L8104
D207
RN
142S
D208
LR79G0GK3N9B3.9n
L227
$C
209
6.0
p
C268
9.5
TL34-4
902-0
5
L1
*L2
*C265
$C
208
*C264
*C267
2.5T
L34-4758-05L3
2.5T
L34-4758-05L4
ANT0
R5
TH1
47p
C237
LB
73H
0A
V-0
03
L217
$R
201
100k
NC
U15W
F104F
6S
TH
201
-t
TH2
47p
C266
$R
210 100k
NC
U15W
F104F
6S
TH
202
-t
0.1
u
C260
VPoS
8
VAPC
7
NC
6
CoMM
5FLTR4
VSET3
ENBL2
RFIN1
AD8315ARMIC205
LB73H0AY-004L225 L
B73H
0A
V-0
03
L226
-t
470pC270
3.9k
R267
33k
R282
NC
U15W
F104F
6S
TH
203
90T
90ANT
DE
T
FWD
$R
264
$C
240
$C
248
V+8
BoUTPUT7
B-INPUT6
B+INPUT5
V-
4
A+INPUT
3
A-INPUT
2
AoUTPUT
1
$IC204
$R
237
$R
234
$R
236
$R254
$C246
4700p
C263
22k
R259
270k
R266
120k
R260
0
R203
22k
R265
47p
C236
15k
R251
22k
R245
22k
R244
120k
R250
AP
C1
+B
4700p
C239
Q204LSCR523EBFS8
10k
R247
2.2
kR
230 2.7k
R24147k
R229
CN31
Ram
p_O
ffset
120p
C213
0.0
1u
C2141
k
R271
$R
232
18k
R273
22k
R275
22k
R274
10k
R213
470p
C271
470p
C272
$C210EMD9Q205
RE
V
TX
PW
R_H
_/L
SP
C
50C
T
50C
T
TH
P2L
B73H
0A
Y-0
04
L208
CN30
CN32
50C
T
470p
C251
0.1
u
C252
RN142SD202
47
R261
$R
208
470R258
90T
470p
C232
100p
C231
2.2
k
R227
3.9k
R228
$C
203
$C
269
$C
204
ED
ZV
5.6
B
D201
$D
203$Q203
Q202LSCR523EBFS8
$R263
2.2k
R231
$R253
22k
R235
$R
255
270
R248
$R
257
47
R238
$R
202
0
R204
TX:9.0VRX:0V
90T
/DS
W
TX
C
AN
TS
W
LTC014EEBFS8Q23
4.7
k
R72
CN29CN93CN92
Q20SSM3J334R
10k
R71
47p
C67
Q22SSM3J334R
LTC014EEBFS8
Q21
10k
R73
4.7
k
R74
9.0V
90C
AD
J
5
VoU
T
4
GN
D
3
VC
C
2
CT
L
1
BA00DD0WHFPIC1
5.0V
50CT
16
1uC68
0.1
uC
66
16
2.2
uC69
47u
C65
25
4.7
uC
64
VoU
T
5
VIN
4
CE
3
VS
S
2
NC
1XC
6209B
502P
-GIC
16
1k
R69
(D)
1.5
k
R83
(D)
27k
R70
(D)
4.7
kR84 3.3
R82
2.7
R81
470pC212
16
1uC
211
LB
73H
0A
Y-0
04
L207
VT
6M
1Q
206
1kR212
470k
R211
0
R278
20V DC/DC
50C
390p
C62
390p
C61 CK
730F
A1H
475K
4.7
uC
63
10u
C58
10u
C59
CK
73F
XR
1E
475K
4.7
uC
60
RB561VM-40D17
SW
6
NC
5
FB
4EN3
VIN2
GND1
TPS61041DRVRIC14
LR79Z0AA150M
15uL14 10R68
22k
R67
330k
R6610
R65R92-3769-0510
R64
19.6V
CV
AS
TS
W
VC
O_M
OD
AS
SIS
T
200C
200C
CV
0.0
1u
C108
CC730AD1H104J0.1uC116
100p
C110
100p
C112
33pC109
1u
C111
ED
ZV
8.2
BD
101
V+
8
BoU
TP
UT
7
B-I
NP
UT
6
B+
INP
UT
5
V-
4
A+
INP
UT
3
A-I
NP
UT
2
AoU
TP
UT
1
NJM
2904C
RB
1IC
101
EM6M2Q103
0R
117
$R
102
1k
R112
1k
R113
100k
R122
100k
R128
10MR125
12k
R132
120kR115
2.2
kR
119
22k
R114
47
R127
4.7
kR
121
CN23
CN22
CN25
5.0V
50C
16
10u
C130
100p
C125
1S
S400S
M
D107
LB73H0AY-004
L119
Q1042SD2654/W/
47k
R134 47k
R133
10k
R135
CN24
AT
T_S
W
$C107 $R107
CN33
*C144
9p
C143
0.5pC142
*C141 0.5p
C140
9p
C139
*L120
*L121*L123
*L124
*L122
RX HPF
8p
C3084pC309
7pC310
4p
C339
1S
S390
D301
1S
S390
D302
LR
79G
0C
Q12N
G
12n
L304
LR
79G
0C
Q18N
G18n
L313
LR
79G
0C
Q18N
G18n
L303
$C
318 1
SS
400S
M
D304
1S
S400S
M
D303
$L315
*C337
$L317
0
R318
SB
2
AS
SW
50C
T
CN28
DD
RC
_D
[15]
DD
RM
_D
[14]
DD
RM
_D
[1]
DD
RM
_A
[12]
DD
RM
_W
E
DD
RM
_D
QS
[1]
DD
RM
_A
[2]
DD
RC
_B
A[1
]
DD
RC
_B
A[0
]
DD
RM
_B
A[1
]
DD
RM
_C
LK
P
DD
RM
_D
[3]
DD
RC
_D
QS
[1]
DD
RC
_D
QS
[0]
DD
RC
_D
QM
[1]
DD
RC
_D
QM
[0]
DD
RC
_C
S
DD
RC
_C
AS
DD
RC
_R
AS
DD
RC
_W
E
DD
RC
_C
KE
DD
RC
_C
LK
N
DD
RC
_C
LK
P
DD
RC
_A
[0]
DD
RC
_A
[1]
DD
RC
_A
[2]
DD
RC
_D
[4]
DD
RM
_A
[7]
DD
RC
_A
[12]
DD
RC
_A
[13]
DD
RM
_D
[15]
DD
RC
_A
[11]
DD
RC
_D
[10]
DD
RC
_A
[4]
DD
RM
_D
QM
[0]
DD
RM
_D
[13]
DD
RM
_D
[11]
DD
RM
_B
A[0
]
DD
RC
_D
[3]
DD
RM
_D
QM
[1]
DD
RM
_A
[6]
DD
RM
_R
AS
DD
RM
_A
[3]
DD
RC
_A
[6]
DD
RM
_A
[9]
DD
RC
_D
[2]
DD
RC
_D
[6]
DD
RM
_D
[5]
DD
RM
_A
[8]
DD
RM
_D
[0]
DD
RM
_C
LK
N
DD
RC
_A
[9]
DD
RC
_A
[8]
DD
RM
_A
[4]
DD
RM
_D
[12]
DD
RC
_A
[7]
DD
RC
_D
[14]
DD
RC
_D
[12]
DD
RM
_C
S
DD
RM
_C
AS
DD
RM
_C
KE
DD
RC
_A
[5]
DD
RC
_D
[1]
DD
RM
_D
[7]
DD
RC
_D
[13]
DD
RC
_D
[5]
DD
RC
_D
[9]
DD
RM
_A
[13]
DD
RM
_D
[10]
DD
RM
_A
[5]
DD
RM
_D
[4]
DD
RM
_A
[10]
DD
RM
_D
QS
[0]
DD
RM
_D
[6]
DD
RM
_D
[8]
DD
RC
_D
[11]
DD
RC
_A
[3]
DD
RC
_A
[10]
DD
RC
_D
[0]
DD
RM
_A
[1]
DD
RM
_A
[0]
DD
RM
_A
[11]
DD
RC
_D
[7]
DD
RC
_D
[8]
DD
RM
_D
[2]
DD
RM
_D
[9]
22
R491
22
R459
22
R452
22
R458
22
R466
22
R469
22
R472
22
R442
22
R475
22
R448
22
R450
22
R482
22
R457
22
R445
22
R480
22
R463
22
R454
22
R487
22
R447
22
R455
22
R481
22
R493
22
R474
22
R453
22
R490
22
R461
22
R451
22
R478
22
R443
22
R479
22
R456
22
R492
22
R460
22
R473
22
R476
22
R449
22
R484
22
R477
22
R464
22
R465
22
R471
22
R467
22
R446
22
R470
22
R468
CN
70
CN
69
100p
C305
100p
C3041000p
C331
VCTL1
6
PC
5
VCTL2
4P23
GND2
P11
NJG1608KB2IC301
Q301SSM3K15AMFV
22k
R307
47
R309
22k
R310
32M
TXD1
RXD1
/ADC
TX
RXD2
RX
SCK1
/EVCS
/PTT
32M
/DACCS
TXD2
32A
RXD0TXD0
SDI0
SDO0
10k
R498
10
R536
10
R537
/INT15P
/KEYINT
/ADC_INT
BER_DATA
BER_CLK
SP_MUTE
SDO1
/DM_EN
BT_AUD_DI
BT_AUD_DO
/DCR_CS
/CRST
I2CDT
PRST
/DSW
ANTSW
I2CCK
TXC
ATT_SW
TXPWR_H_/L
DCR_DI
DCR_DDO
/DCR_DCS
BCLK
RTS2
WCLK
CODEC_DI
/DCR_ACS
(TXSLOT) RTS1
DCR_ACLK
DCR_DO
CODEC_DO
SYMTIM_IN
/BINT
CTS1
DCR_ADI
330
R526
CN71
CN94
UART2_SW1
32M
D33_RXD2
UART2_SW2
D33_TXD2
P_TXD2
P_RXD2
SCK0
0.0
1u
C487
0.0
1u
C488
VCC
10
S9
D+8
D-7
oE6
GND
5
2D-
4
2D+
3
1D-
2
1D+
1
BD11600NUXIC405
VCC
10
S9
D+8
D-7
oE6
GND
5
2D-
4
2D+
3
1D-
2
1D+
1
BD11600NUXIC406
/VB
US
_D
ET
VER2
$R401
1k
R488
$R402
MODEL
VER1
32M
PRST_MON
R_S
ET
0
R_S
ET
1
R_S
ET
2
UA
RT
2_S
W2
UART2_SW1
/BT_SHUTDOWN
GPS_PA_EN
UMode
C510
EX
PA
D25
A2
24
A1
23
INT
22
VC
C
21
SD
A
20
SC
L
19
A018
P1717
P1616
P1515
P1414
P1313
P12
12
P11
11
P10
10
GN
D
9
P07
8
P06
7
P05 6
P04 5
P03 4
P02 3
P01 2
P00 1
TCA9555RTWRIC409
$R415
/IN
T_IO
I2C
DT
I2C
CK 0.1u
10k
R525
4.7
k
R517
4.7
kR
514
DM_IN
DM_OUT
/DM_EN
50A
32M
0.01uC498
0.0
1u
C491 VCC
5
oUTY
4 GND 3
INA
2
INB
1
TC7SZ08FEIC408
VCC 5
oUTY
4GND3
INA2
G1
TC7SET125FUF
IC407
1k
R503
33k
R511
47k
R505
/BT
_S
HU
TD
OW
NW
CLK
GP
S_P
A_E
N
54M
RT
S2
BT
_A
UD
_D
OB
T_A
UD
_D
IB
CLK
BT
_S
W
CT
S2
GP
S_A
LM
GP
S_P
WR
GP
SB
T_D
ET
GP
S_A
NT
_S
W
47
0R
489
0.0
1u
C412
1000p
C411
1000p
C410
1000p
C484
1k
R418
10*4
CP
405
10*4
CP
404
10*4
CP
403
5.4V
1u
C489
TO MODULE (BT/GPS) UNIT (XC2-004) CN1
20
19
18
17
16
15
14
13
12
11
10987654321
E40-6862-05CN2
R_S
ET
1
/VB
US
_D
ET
18M
_1
R_S
ET
0
R_S
ET
2
100p
C492
Q402SSM3K15AMFV
100k
R502
100k
R501
10k
R499
CN80
DA
TA
[6]
DA
TA
[7]
DA
TA
[5]
DA
TA
[4]
DA
TA
[3]
DA
TA
[2]
DA
TA
[1]
DA
TA
[0]
/OE
/WR
AD
D[2
3]
US
B0_D
M
MIC
ME
P_T
EM
P
/CS
4
PR
ST
_M
ON
PR
ST
/KE
YIN
T
I2C
CK
I2C
DT
RX
D0
TX
D0
/PS
W
/PT
T
RB
521C
M-3
0
D410
47*4
CP
413
47*4
CP
414
47*4
CP
412
CN78
CN76
CN77CN82
CN81
/CS
_LC
D/R
D_LC
D/W
R_LC
DD
C
/CS
_LC
D/R
D_LC
D/W
R_LC
DD
C1000pC514
L79-1
984-0
5L419
Q403
SS
M3K
15A
MF
V
$R
4090
R520
0R
516
0R
519
DA
TA
7D
AT
A6
DA
TA
5D
AT
A4
DA
TA
3D
AT
A2
DA
TA
1D
AT
A0
2
1
109
58
37
64L415
2
1
109
58
37
64L416
0R
407
$R
406
0R
408
0R
539
$R
540
$R
541
2
1
109
58
37
64
DA
TA
1D
AT
A2
DA
TA
5D
AT
A4
DA
TA
7
DA
TA
3
DA
TA
6
DA
TA
0
0.1uC521
1000p
C12
0.1
uC
511
0.1
uC
520
RB521CM-30D408
RB521CM-30
D409
EDZV8.2B
D407
3.3
k
R524
3.3
k
R523
3.3
k
R522
13.6V5.4V
1.8V
3.2V
US
B0_D
P
SP
O
/IG
N
18M
32M
54M
SB
1
31B
U
$C512
$C513
0.0
1u
C522
1000pC523
NC
3VIN2
VSS
4VOUT1
XC61CN5002N-GIC413
LT
C014T
EB
FS
8Q
404
100k
R527CN75
CN74
100p
C501
0.1
uC
519
LB
73H
0A
Y-0
02
L418
LB
73H
0A
Y-0
02
L417
SP
C10501A
01
D402
D403
100p
C509
100p
C506
100p
C505
100p
C503
100p
C507
D404
D405
SP
C10501A
01 D406
$R
414
$R
413
$R
411
$R
412
SB
SP
G
TO SUB UNIT (XC3-050) CN7
NC
(IG
N)
NC
GN
D
SP
G
SP
+
R_S
ET
0
NC
NC
R_S
ET
1
32M
SP
+
R_S
ET
2
US
B_D
-
SP
+
GN
D
GN
D
/PS
W
A[2
3]
NC
GN
D
/WR
GN
D
NC
D[0
]
GN
D
D[1
]
GN
D
D[2
]
GN
D
D[3
]
SB
D[4
]
SB
D[5
]
ME
D[6
]
SB
D[7
]
MIC
/VB
US
/RD
SP
G
LC
DR
ST
/PT
T
/CS
P_T
EM
P
/KE
YIN
T
I2C
CK
I2C
DT
GN
D
RX
D
TX
D
DM
/KV
L
NC
GN
D
US
B_D
+
18M
NC
54M
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
987654321
EC720AA-0560ACN1
(-71)
120n
L210
1.5p
C317
5pC311
6p
C319
$L316
LR
79G
0C
Q39N
G39n
L309
470
R315 12
R314
470
R313
15pC320
LR
79G
0C
QR
22G
220n
L311
LR
79G
0C
Q22N
G22n
L310
LR
79G
0C
Q39N
G
39n
L308
THP1
25VREF
VREF
50A
25REF
$C
404
$C
403
0.1u
C527 1u
C528
1u
C493
1u
C526
0.1
u
C495
0.1
u
C497
VDD
8
oUT2
7
IN2-
6
IN2+
5VSS4
IN1+3
IN1-2
oUT11
BU7462NUXIC414
+VA232
REFP31
REFM30 CH9 11
CH10 10
CH11 9
CH
12
8
CH
13
7
CH
14
6
CH
15
5
AIN
M
4
AIN
P
3
MX
o
2
AG
ND
1
1
0
R531
0R532
100
R496
100
R497
100
R495
100
R494
1k
R500
$R405
$R404
(D)
22k
R530
(D)
22k
R533
(D)
22k
R529
(D)22kR534
100*4CP409
/ADC_INT
P_T
EM
P
GP
S_A
LM
GP
S_P
WR
RE
VT
HP
2T
HP
1T
EM
P
CV
Ram
p_O
ffset
32M
/AD
C
BLV
L
50A
SD
I0S
DO
0S
CK
0
0.1u
C494
0.1u
C502
47p
C524
47p
C525
$C
402
GPIo29
+VBD28
BDGND27
SDo26
SDI25
SC
LK
24
CS
23
AG
ND
2
22
+V
A1
21
CH
0
20
CH
1
19
CH
2
18
CH
3
17
CH4 16
CH5 15
CH6 14
CH7 13
CH8 12ADS7961SRHB
IC410
LB73H0AV-002L414
0
R504
10kR50710kR508
22k
R513
22k
R512
$R
403
47k
R518
(D)100kR506
100kR535
100*4
CP
406
100*4CP408
100*4
CP
407
CN72
DAC
12bit/4ch
APC
AP
C1
32A
18M
_3
AS
SIS
T
SCK1/DACCSSDO1
FC
NT
$C
413
1u
C515
0.1
u
C516
$C
406
$C
407
SCLK
10
SYNC9
DIN8
VREFIN7
GND6
VoUTD
5
VoUTC
4
VoUTB 3
VoUTA
2
VA
1
DAC124S085CISIC411
$R
419
100*4
CP410
DAC E-Vol
8bit/8ch
CODEC
SP
C
SDO1SCK1/EVCS
32A
VREF
1uC655
161u
C517
4700p
C405
100pC518
$C
408
$C
409
VoU
T2
24
VoU
T1
23
VIN
122
VIN
821
VoU
T8
20
VoU
T7
19
VIN7 18
GND 17
RESET 16
VDAREF2 15
VDAREF1
14
VIN6
13
VoU
T6
12
VoU
T5
11
VIN
510
VIN
49
VoU
T4
8V
oU
T3
7
VIN36
DI5
CLK4
LD3
VDD2
VIN21
R2A20178NPIC412
$R521
0
R416
10k
R509
100*4CP411
CN50
CN79
AFO_SP
$R521
3.2V
19.2MHz
I2CDTI2CCK
MCLK
BCLK
CODEC_DICODEC_DOWCLK
0.1u
C638
LB73H0AV-003L602
10R660
10*4
CP604
100*4CP605
1.8V1uC639
0.1uC640
LB73H0AV-003
L601
1k
R662
100k
R661
DV
DD
32
RE
SE
T31
RIG
HT
_LoM
30
RIG
HT
_LoP
29
LE
FT
_LoM
28
LE
FT
_LoP
27
AV
SS
226
AV
DD
25
DRVDD2
24
HPRoUT
23
HPRCoM 22
DRVSS 21
HPLCoM 20
HPLoUT 19
DRVDD1 18
AVSS1 17
MIC
2R
/LIN
E2R
16
MIC
BIA
S
15
MIC
2L/L
INE
2L/M
ICD
ET
14
MIC
1R
M/L
INE
1R
M13
MIC
1R
P/L
INE
1R
P12
MIC
1LM
/LIN
E1LM
11
MIC
1LP
/LIN
E1LP
10
SD
A9
SCL8
IoVDD7
DVSS6
DoUT5
DIN4
WCLK3
BCLK2
MCLK1
TLV32AIC3104IIC607
CN87
0.1
uC
645
1u
C649
0.1
uC
642
0.1
uC
643
0.1
uC
641
0.1
uC
644
0.1
uC
650
DA
204U
D612
DA
204U
D613
0
R665
3.2V
32A
DI
MIC10uC636
10u
C646
1k
R664
1kR676
680
R673
100k
R677
0.0
22u
C65310u
C656
1k
R668
680
R669
50A
ME
0
R674
6.8
k
R675
AFOAMPAFAMPDSUBExSP
25REF
50A
0.1
uC
657
1u
C659
1u
C652
68p
C658
VDD
8
oUT2
7
IN2-
6
IN2+
5VSS4
IN1+3
IN1-2
oUT11
BU7462NUX
IC608
(D)27k
R672
47k
R671
1u
C661 100p
C651
100
R658
68k
R666
12k
R667
RXD1
50A
32M
CTS1
RXD1
SB2
100k
R618
10k
R615
CN90
CN91
TXD1
TXD1
RTS1
0.0
1u
C605
RB
521C
M-3
0
D615
VCC
8
G2
7
Y1
6
A2
5GND4
Y23
A12
G11
TC7WT126FU-F
IC602
100k
R622
CN89
0.01u
C606
RB521CM-30
D602
VCC
8
G2
7
Y1
6
A2 5
GND
4
Y2
3
A12
G11
TC7WH126FKIC603
CN97
CN95
157
8
16
0
R625
$R
604
$R
605
0
R623
CTS
RTS
RXD
TXD
501uC609
501u
C611
501uC610
501u
C612
0.0
1u
C608
RB521CM-30D614
VCC
16
GND
15
R2IN
8
T1oUT
14
R1IN
13
R1oUT
12
T1IN
11
T2IN
10
R2oUT9
T2oUT
7
V-
6
C2-
5
C2+
4
C1-
3
V+
2
C1+
1
ADM3202ARUZ
IC605
50A
D33_TXD2
D33_RXD2
BER_DATABER_CLK
BER_EN
0.0
1u
C635
RB521CM-30
D610
RB521CM-30
D609
ED
ZV
6.8
B
D611
VCC 5
oUTY
4GND3
INA2
G1
TC7SET125FUFIC606
1kR656
1kR657
10k
R617
10k
R616
CN88
2
1
4100p
C625
F53-0286-05
F6
TP
CP
8107-F
Q603
0
R627
$R602$R603
$R607
470
R626
$R606
AV
RM
10270K
101
D617
1000pC613
RB520SM-30D618
HORN ALERT SW 3
LTC014TEBFS8Q602
0
R628
4.7k
R629
47k
R632
AVRM10270K101D616
13.6V
FNC5
DATAI
DATO
SB
GND
HR
2
HR
1
100pC622
100p
C623
100pC624
100pC620
0.022uC621
F53-0286-05
F3
L603
100R624
470R640
14
13
12
11
10
9
0R631
$R
610
$R
609
0R633
$R
6080
R630
50
FNC6
FNC4
FNC3
FNC2
FNC1
SP2
IGN
6
100pC617
100pC616
100pC615
100pC618
1000pC660
100pC614
100pC619
100R638
100R639
100R637
0
R614
470R636
100R635
5
$R
611
0
R634
D-Sub15
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
E58-0567-05J1
ED
ZV
6.8
B
D608
ED
ZV
6.8
B
D607
ED
ZV
6.8
B
D606
ED
ZV
6.8
B
D605
ED
ZV
6.8
B
D604
ED
ZV
6.8
B
D603
5.0V50AC
19 18
17
2.2
u
C665
470p
C663
50
1uC664
10u
C637
ED
ZV
5.6
B
D601
CE3 VSS 2
VIN4 VoUT 1
XC6221D501G-GIC609
0R613
$R612
0
R641 330
R679
330
R670
330
R678
47k
R642
CN96
20
54M
IGN
SBC
DI
AFO
DEO_0
R659
$R601
32M
50A
/INT15P
I2CDT
I2CCK
DEO_0
0R
528
$R417
0.1
u
C607
SSM6N15AFEMQ601
10k
R619
4.7
k
R621
4.7
k
R620
330
R680
EXPAD
25
A224
A123
INT22
VCC21
SDA20
SCL19
A0
18
P17
17
P16
16
P15
15
P14
14
P13
13
P12 12
P11 11
P10 10
GND 9
P07 8
P06 7
P05
6
P04
5
P03
4
P02
3
P01
2
P00
1
TCA9555RTWRIC604
4.7k*4
CP601
4.7k*4
CP602
1u
C647
0.1
u
C648 0
R663
SPO
PA_MUTE
SP_MUTE
0.22u
C627
0.22u
C628
1u
C631
1u
C626
0.1
u
C633
0.1
u
C634
LTC014TEBFS8Q604
SSM6N15AFEM
Q605
2.2k
R648
2.2k
R649
22k
R654
22k
R655
6.8
k
R653
6.8
k
R647
22k
R652
22k
R646
32M
SB1
25
47u
C4
RB521CM-30
D619
Q606SSM3J334R
1.5k
R681
1k
R645
4.7
uC
632
oU
T1
12
NC
2
11
PW
RG
ND
10
NC
1
9
oU
T2
8
VC
C
7
PP
6
ST
BY
5
IN2
4
PR
EG
ND
3
IN1
2
RF
1
LA4631VC-XEIC601
13.6V
1000p
C629
16
330uC
2
16
330uC
3
F53-0286-05
F2
1k
R644
0
R650
0
R651
10k
R643
1000p
C630
0
EXT.SP
E1B-0001-00J2
/SA
VE
*C146
*C148
*C104
*C147
1000p
C145 *L102*L104
0
R145
*R108*R109
/CRST
0.01uC235
VCC8
oUT27
-IN26
+IN25 VEE 4
+IN1 3
-IN1 2
oUT1 1
BA3472FVMIC203
TX-RX UNIT (XC1-183K-00 (NX-3820H(G), NX-3820H, NX-3820(G), NX-3820))
A
1
B C D E F G
2
3
4
5
6
7
8
9
10
H I J K L M N O P Q(No.RA054<Rev.001>) 2-16
A
1
B C D E F G
2
3
4
5
6
7
8
9
10
H I J K L M N O P Q(No.RA054<Rev.001>) 2-17
DC in
GND
+B
LPFANT
SW
DC
SW90C
ANTSW
Q22SSM3J334R
HPF
IC301NJG1608KB2
/DCR_RST,RX,TX,AGCKEEP,BCLK , /DCR_CS,DCR_DO,DCR_DI,DCR_ACLK,
Loop
Filter
VCOBUFF
200CIC101
ASSIST
ASTSW
NJM2904CRB1Q103 VT6M1
VCO_MOD
Q1062SC5108FT/Y/
50C
32C
Q105
D102
D103,104,105,106
SMV1270-079LF
MCH3914-H/8/
1SV282-F
D101 EDVZ8.2B
IC13BU31TD2WNVX
3.1V Reg
1.2V Reg
IC5XC6215B122N-G
31BU
12BU
5.4V DC/DC
Converter
54M
3.2V Reg
54M
3.2V Reg
1.2VDCDC
1.8VDCDC
F53-0286-05F1
MP2560DQ-LF-ZIC25
18M_3
IC21XC8102AA07-G
18M
32A
32M
12M
IC24LXDC2XQ12A-252
IC5XC6223D331P-G
IC12LXDC2HN18F163
IC17NJM2878F4-32
ADS7961SRHBIC410
ADCCV,P_TEMP,Ramp_Offset,BLVL,TEMP
IC411
DAC
DAC124S085CIS
APC,ASSIST,FCNT
IC412
DAC
R2A20178NP
SPC,SPAF
SCK0,SDO0.SDI0
/EVCS
/DACCS
/ADC,/ADC_INT
L79-1984-05L415,L416,L419
/CS4,/OE,/WR,ADD[23]
DATA[0]~DATA[7]
CN1
IC404
IC402
IC401
DDR_A[0]~DDR_A[13]
DDR_BA[0],DDR_BA[1]
DDR_CAS,DDR_CKE,DDR_CLKN
DDR_CLKP,DDR_CS
DDR_DQM[0],DDR_DQM[1]
DDR_RAS,DDR_WE
DDR_DQS[0],DDR_DQS[1]
DDR_D[0]~DDR_D[15]
DATA[0]~DATA[15]
/FRST,/OE,/WP,/WR
ADD[0]~ADD[23]
IC403TC7SZ08FE
/CS2
/CS3
/CS_F
PLL_CLK
Q4012SC4617/S/
L7H-0076-00X401
D205 L8104D206 L8104
54M
/CS,/RD,/WR,A[23],D[0]~D[7]
---------------------------------------------------------
--TX--
ANTSW,/DSW,TXC,ASSW,TXPWR_H_/L
---------------------------------------------------------
--RX--
ATT_SW
---------------------------------------------------------
--AUDIO--
SP_MUTE,PA_MUTE
---------------------------------------------------------
--3.2V Reg(IC19),5V Reg(IC609),DC SW(Q13,Q12)--
SBC
---------------------------------------------------------
--Logic IC(IC407,IC408)--
DM_OUT,/DM_EN,DM_IN
---------------------------------------------------------
136~174MHz
LTC014EEBFS8Q21
CTRL
PA
DET
REV
RB706F-40D204
AD8315ARMIC205
50CT
SPC
DC BA3472FVMIC203
90T
AMP AMP
DC
1/22/2
90T
Q204
DC SW
LSCR523EBFS8
REV
COUPLER
DC SW
Q202LSCR523EBFS8
/DSW
IC201RA60H1317A501
Gate Bias
RF POWER MODULE
+B
AMP
DRIVE
Q201RFM01U7PF
90T
BGU6104
AMP
DRIVE
IC202
50CT
DC SW ASSW
VT6M1Q206
Ramp_
Offset
2/2
DC SW
BPF
50C
Q1041SS400SMD107
Filter
Ripple
2SD2645/W/
Protect
D208/D209
(13.6V(K), 13.2V(E))
5V50BU
Q16LSAR523UBFS8
Q15LSCR523EBFS8
EDZV5.6BD13
Q1KTA2012EP
SSM3K15AMFVQ3
DC SW54M
VT6M1Q19
DC SW
5.0V Reg50A
IC26XC6221D501G-G
5.0V Reg
IC6XC6221D501G-G
50C
SBC
SBC
3.2V Reg
XC6223D321G-GIC19
FZA10BS-5R0F4
BAT_CNT
Q13LTC014EEBFS8
DC SW
TPCP8107-FQ12
SBC
TPCP8107-FQ17
LTC014EEBFS8Q18
FZA10BS-5R0F5
DC SW
SBC
20VDC/DC
IC13TPS61041DRVR
Converter
EM6M2Q12
DC SW
/SAVE
50CS
200C
SB1
SB2
9.0V Reg
IC1BA00DD0WHFP
5.0V Reg
IC16XC6209B502P-G
50CT
90C
18M
32M
18M_3
FCNT
32M
To
SU
B U
NIT
32M
18M
DM/KVL
R_SET0,R_SET1,R_SET2,PRST_MON
THP1,THP2,REV,GPS_PWR,GPS_ALM
CODEC_DI,CODEC_DO
I2CCK,I2CDT,/CRST
BCLK,WCLK,MCLK
IC607
CODEC
TLV32AIC3104I
18M_3 32A
MI2ME
MIC/VBUS
DETO
DATAI
50A
1/2
IC608BU7242UNX
BU7242UNX2/2
AFO
IC608
AFO_SP
AFO_D
50A
LA4631VC-XE
SB2
IC601
TC7SZ08FEIC408
DM_OUT
/DM_EN
DM_IN
TC7SET125FUFIC407
EX
T S
P
J2
TCA9555RTWRIC604
I/O
EXPANDER
I2CCK
I2CDTLEVELCONVERSION
SSM6N15AFEMQ601
50A
RS-232C
Driver
ADM3202ARUZIC909
50A
RXD(RS232C)
TXD(RS232C)
CTS(RS232C)
RTS(RS232C)
TXD1
RXD1
CTS1
RTS1
SB2
50AC
D33_RXD2
IC606
D33_TXD2
50A
J1
E-Vol
IC406
DPDT
SW
32M
BD11600NUX
UART2_SW2
P_TXD2
P_RXD2
DPDT
SW
UART2_SW132M
BD11600NUXIC405
G_TXD2
G_RXD2
TXD2
RXD2
32MIC409
I/O
EXPANDER
TCA9555RTWR
TCXO Buffer
I2CCK
I2CDT
UART2_SW1
UART2_SW2
GPS_PA_EN
/BT_SHUTDOWNUMode
/INT_IO
/IGN
Q18XC61CN5002N-G
HORN
GPS_ANT_SW,WCLK,BCLK,BT_AUD_DI,BT_AUD_DO
RTS2,CTS2,BT_SW,GPSBT_DET
G_RXD2
G_TXD2
GPS_PWR
GPS_ALM
GPS_PA_EN
/BT_SHUTDOWN
54M
CN2
Power
Managment
MSP430G2533P0IC22
31BU
/OVRB_OUT,/IGN_OUT,/PSW_OUT
PWR_CNT,/BINT2,/RST,/BINT
D20EDZV18B
Q11LTC014EEBFS8
DC SW/OVRB
/OVRB
P_TXD2
P_RXD2
BAT_CNT
/IGN
/PSW
Bluetooth
2400-2483.5 MHz
L11L79-1987-05
BPF
L9L79-1985-05
BPF
GPS_PWR
GPS_ALM
32.768kHz
L77-3123-05X1
X2
19.2MHz
TXCO
DC
SW33BT
EM6M2Q1
NL5500LYFVRIC5
BLUETOOTH
33BT
GPS
1575.42MHz
18BT
GPS
18BT
33GPS
L77-3121-05
XO
18BT_HCI_TX,18BT_HCI_RX
BTFM_nSHUTDoWN,GPS_PA_EN
18BT_AUD_OUT,18BT_AUD_IN
18BT_AUD_FSYNC,18BT_AUD_CLK
18BT_HCI_CTS,18BT_HCI_RTS
74AVC4TD245GUIC1,6,7
CONVERSION
LEVEL
33BT
18BT
BU18TD2WNVX
XC6209B332D-G
IC4
BT_SW
18BT
33GPS
54M
33BT
GPS_ANT_SW
1.8V AVR
3.3V AVR
NJM2878F4-33
IC2
IC3
3.3V AVR
GPS_PWR,GPS_ALM
54M
BT_SW,GPS_ANT_SW
WCLK,BCLK
CN1
RTS2,CTS2
BT_AUD_DI,BT_AUD_DO
/BT_SHUTDOWN,GPS_PA_EN
RXD2,TXD2
DDR
FLASH
SW
Q605SSM6N15AFEM
SP_MUTE
19.2MHz
ANT
DET
SSM3J334RQ20
LTC014EEBFS8
TXC
Q23
90CDC
SW90T
TC7SET125FUF
RN142S
XC1-182
TX-RX UNIT32C
D207 L8104
ATT
D303/D3041SS400SM
TRANCEIVER IC
AK2401IC302
Q1072SC5108FT/Y/
D108SMV1130-079LF
CP
CPZ
200C
CV
IC101NJM2904CRB1
1/2
ATT
LNAoUT
VCO_MOD
PLL_CLK
ATT_SW
SSM3K15AMFVQ301
PLD,DCR_ADI,/DCR_ACS,/DCR_DCS,DCR_DDO
32M
USB_D+,USB_D-,/PTT,TXD.RXD,I2CDT,I2CCK,/KEYINT,PRST
SB1
/VBUS_DET
SSM3K15AMFVQ402
MIC
/PSW
P_TEMP
BER_EN
SW
HR1
HR2
Q602LTC014TEBFS8
Q603TPCP8107-F
F53-0286-05F6
D33_RXD2
D33_TXD2
FNC1(TXD),FNC2(RXD),FNC3(RTS)
FNC4(CTS),FNC5,FNC6
IGN
SP2
DETO(AFO)
DATAI(MI2)
5.0V Reg
IC609XC6221D501G-G
50AC
SBC
TXD
RXD
CTS
RTS
AFO_SP
SPAF
SW
Q605SSM6N15AFEM
PA_MUTE
SPO
F53-0286-05F2
SCK1,SDO1
SCK1,SDO1
TEMP
THP1
TEMP
THP2
/INT15P
SW
TXPWR_H_/L
Q205EMD9
RN142SD202
D-su
b
BUFF
TX-RX Unit (XC1-182)
Module (BT/GPS) Unit (XC2-004): NX-3720H(G), NX-3720(G) only
BLOCK DIAGRAM TX-RX UNIT (NX-3720H(G), NX-3720H, NX-3720(G), NX-3720)
A
1
B C D E F G
2
3
4
5
6
7
8
9
10
H I J K L M N O P Q(No.RA054<Rev.001>) 2-18
TX-RX Unit (XC1-183)
DC in
GND
+B
K :450~520MHz
LPFANT
SW
DCSW 90C
ANTSW
Q22SSM3J334R
HPF
IC301NJG1608KB2
/DCR_RST,RX,TX,AGCKEEP,BCLK ,/DCR_CS,DCR_DO,DCR_DI,DCR_ACLK,
Loop
Filter
VCO BUFF
200CIC101
ASSIST
ASTSW
NJM2904CRB1Q103 VT6M1
VCO_MOD
Q1062SC5108FT/Y/
50C
32C
Q105
D102
D103,104,105,106
SMV1270-079LF
MCH3914-H/8/
1SV282-F
D101 EDVZ8.2B
IC13BU31TD2WNVX
3.1V Reg
1.2V Reg
IC5XC6215B122N-G
31BU
12BU
5.4V DC/DC
Converter54M
3.2V Reg
54M
3.2V Reg
1.2VDCDC
1.8VDCDC
F53-0286-05F1
MP2560DQ-LF-ZIC25
18M_3
IC21XC8102AA07-G
18M
32A
32M
12M
IC24LXDC2XQ12A-252
IC5XC6223D331P-G
IC12LXDC2HN18F163
IC17NJM2878F4-32
ADS7961SRHBIC410
ADC CV,P_TEMP,Ramp_Offset,BLVL,TEMP
IC411
DAC
DAC124S085CIS
APC,ASSIST,FCNT
IC412
DAC
R2A20178NP
SPC,SPAF
SCK0,SDO0.SDI0
/EVCS
/DACCS
/ADC,/ADC_INT
L79-1984-05L415,L416,L419
/CS4,/OE,/WR,ADD[23]DATA[0]~DATA[7]
CN1
IC404
IC402
IC401
DDR_A[0]~DDR_A[13]
DDR_BA[0],DDR_BA[1]DDR_CAS,DDR_CKE,DDR_CLKNDDR_CLKP,DDR_CSDDR_DQM[0],DDR_DQM[1]DDR_RAS,DDR_WEDDR_DQS[0],DDR_DQS[1]DDR_D[0]~DDR_D[15]
DATA[0]~DATA[15]
/FRST,/OE,/WP,/WRADD[0]~ADD[23]
IC403TC7SZ08FE
/CS2
/CS3
/CS_F
PLL_CLK
Q4012SC4617/S/
L7H-0076-00X401
D205 L8104D206 L8104
54M
/CS,/RD,/WR,A[23],D[0]~D[7]
-----------------------------------------------------------TX--ANTSW,/DSW,TXC,ASSW,TXPWR_H_/L-----------------------------------------------------------RX--ATT_SW-----------------------------------------------------------AUDIO--SP_MUTE,PA_MUTE-----------------------------------------------------------3.2V Reg(IC19),5V Reg(IC609),DC SW(Q13,Q12)--SBC-----------------------------------------------------------Logic IC(IC407,IC408)--DM_OUT,/DM_EN,DM_IN---------------------------------------------------------
K2,E:400~470MHz
LTC014EEBFS8Q21
CTRL
PA
DET
REV
RB706F-40D204
AD8315ARMIC205
50CT
SPC
DC BA3472FVMIC203
90T
AMP AMP
DC1/22/2
90T
Q204
DC SW
LSCR523EBFS8
REV
COUPLER
DC SW
Q202LSCR523EBFS8
/DSW
IC201
F1:RA60H4452-501F2:RA60H3847-501
Gate Bias
RF POWER MODULE
+B
AMP
DRIVE
Q201RFM01U7PF
90T
BGU6104
AMP
DRIVE
IC202
50CT
DC SW ASSW
VT6M1Q206
Ramp_
Offset
50C
2/2
DC SW
BPF
50C
Q1041SS400SMD107
Filter
Ripple
2SD2645/W/
Protect
D208/D209
(13.6V(K,K2), 13.2V(E))
5V50BU
Q16LSAR523UBFS8
Q15LSCR523EBFS8
EDZV5.6BD13
Q1KTA2012EP
SSM3K15AMFVQ3
DC SW54M
VT6M1Q19
DC SW
5.0V Reg50A
IC26XC6221D501G-G
5.0V Reg
IC6XC6221D501G-G
50C
SBC
SBC
3.2V Reg
XC6223D321G-GIC19
FZA10BS-5R0F4
BAT_CNT
Q13LTC014EEBFS8
DC SW
TPCP8107-FQ12
SBC
TPCP8107-FQ17
LTC014EEBFS8Q18
FZA10BS-5R0F5
DC SW
SBC
20VDC/DC
IC13TPS61041DRVR
Converter
EM6M2Q12
DC SW
/SAVE
50CS
200C
SB1
SB2
9.0V Reg
IC1BA00DD0WHFP
5.0V Reg
IC16XC6209B502P-G
50CT
90C
18M
32M
18M_3
FCNT
32M
To
SU
B U
NIT
32M
18M
DM/KVL
R_SET0,R_SET1,R_SET2,PRST_MON
THP1,THP2,REV,GPS_PWR,GPS_ALM
CODEC_DI,CODEC_DOI2CCK,I2CDT,/CRSTBCLK,WCLK,MCLK
IC607
CODEC
TLV32AIC3104I
18M_3 32A
MI2ME
MIC/VBUS
DETO
DATAI
50A
1/2
IC608BU7242UNX
BU7242UNX2/2
AFO
IC608
AFO_SP
AFO_D
50A
LA4631VC-XE
SB2
IC601
TC7SZ08FEIC408
DM_OUT
/DM_EN
DM_IN
TC7SET125FUFIC407
EX
T S
P
J2
TCA9555RTWRIC604
I/OEXPANDER
I2CCKI2CDT
SSM6N15AFEMQ601
50A
RS-232CDriver
ADM3202ARUZIC909
50A
RXD(RS232C)
TXD(RS232C)
CTS(RS232C)
RTS(RS232C)
TXD1
RXD1
CTS1
RTS1
SB2
50AC
D33_RXD2
IC606
D33_TXD2
50A
J1
E-Vol
IC406
DPDTSW
32M
BD11600NUX
UART2_SW2
P_TXD2
P_RXD2
DPDTSW
UART2_SW132M
BD11600NUXIC405
G_TXD2
G_RXD2
TXD2
RXD2
32MIC409
I/OEXPANDER
TCA9555RTWR
TCXO Buffer
I2CCKI2CDT
UART2_SW1
UART2_SW2
GPS_PA_EN
/BT_SHUTDOWN UMode
/INT_IO
/IGN
Q18XC61CN5002N-G
HORN
GPS_ANT_SW,WCLK,BCLK,BT_AUD_DI,BT_AUD_DORTS2,CTS2,BT_SW,GPSBT_DET
G_RXD2
G_TXD2
GPS_PWR
GPS_ALM
GPS_PA_EN
/BT_SHUTDOWN
54M
CN2
PowerManagment
MSP430G2533P0IC22
31BU
/OVRB_OUT,/IGN_OUT,/PSW_OUTPWR_CNT,/BINT2,/RST,/BINT
D20EDZV18B
Q11LTC014EEBFS8
DC SW/OVRB
/OVRB
P_TXD2
P_RXD2
BAT_CNT
/IGN
/PSW
Bluetooth2400-2483.5 MHz
L11L79-1987-05
BPF
L9L79-1985-05
BPF
GPS_PWRGPS_ALM
32.768kHz
L77-3123-05X1
X2
19.2MHz
TXCO
DCSW
33BT
EM6M2Q1
NL5500LYFVRIC5
BLUETOOTH
33BT
GPS1575.42MHz
18BT
GPS
18BT
33GPS
L77-3121-05
XO
18BT_HCI_TX,18BT_HCI_RX
BTFM_nSHUTDoWN,GPS_PA_EN
18BT_AUD_OUT,18BT_AUD_IN18BT_AUD_FSYNC,18BT_AUD_CLK
18BT_HCI_CTS,18BT_HCI_RTS
74AVC4TD245GUIC1,6,7
33BT
18BT
BU18TD2WNVX
XC6209B332D-G
IC4
BT_SW
18BT
33GPS
54M
33BT
GPS_ANT_SW
1.8V AVR
3.3V AVR
NJM2878F4-33
IC2
IC3
3.3V AVR
GPS_PWR,GPS_ALM
54M
BT_SW,GPS_ANT_SW
WCLK,BCLK
CN1
RTS2,CTS2
BT_AUD_DI,BT_AUD_DO
/BT_SHUTDOWN,GPS_PA_EN
RXD2,TXD2
DDR
FLASH
SW
Q605SSM6N15AFEM
SP_MUTE
19.2MHz
ANTDET
SSM3J334RQ20
LTC014EEBFS8
TXC
Q23
90CDCSW90T
TC7SET125FUF
RN142S
XC1-183
TX-RX UNIT32C
D207 L8104
ATT
D303/D3041SS400SM
TRANCEIVER IC
AK2401IC302
Q1022SC5108FT/Y/
Q1012SC5108FT/Y/
50C
TRIPLER
D108SMV1130-079LF
CP
CPZ
200C
CV
IC101NJM2904CRB1
1/2
ATT
LNAoUT
VCO_MOD
PLL_CLK
ATT_SW
SSM3K15AMFVQ301
PLD,DCR_ADI,/DCR_ACS,/DCR_DCS,DCR_DDO
32M
USB_D+,USB_D-,/PTT,TXD.RXD,I2CDT,I2CCK,/KEYINT,PRST
SB1
/VBUS_DET
SSM3K15AMFVQ402
MIC
/PSW
P_TEMP
BER_EN
SW
HR1
HR2
Q602LTC014TEBFS8
Q603TPCP8107-F
F53-0286-05F6
D33_RXD2
D33_TXD2
FNC1(TXD),FNC2(RXD),FNC3(RTS)
FNC4(CTS),FNC5,FNC6
IGN
SP2
DETO(AFO)
DATAI(MI2)
5.0V Reg
IC609XC6221D501G-G
50AC
SBC
TXD
RXD
CTS
RTS
AFO_SP
SPAF
SW
Q605
SSM6N15AFEM
PA_MUTE
SPO
F53-0286-05F2
SCK1,SDO1
SCK1,SDO1
TEMP
THP1
TEMP
THP2
/INT15P
SW
TXPWR_H_/L
Q205EMD9
RN142SD202
D-su
b
LEVELCONVERSION
CONVERSION
LEVEL
Module (BT/GPS) Unit (XC2-004): NX-3820H(G), NX-3820(G) only
TX-RX UNIT (NX-3820H(G), NX-3820H, NX-3820(G), NX-3820)
A
1
B C D E F G
2
3
4
5
6
7
8
9
10
H I J K L M N O P Q(No.RA054<Rev.001>) 2-19
D
LCD_GND
ESD_GND ESD_GND ESD_GND ESD_GND
ESD_GND
GND
GND
GND
ESD_GND
ESD_GND
GND
ESD_GND
CN7To T
X-R
X U
NIT
MO
DU
LA
R J
AC
K
J1
USB_D+
BLC_3
IC5
DPDTSW
50M
BD11600NUX
BUSSWC
USB_D-HOOK/RXD/D-
BLC/D+
IC3
BUSBUFFER
32M
TC7WH126FK
RXDRXD_50V
/PTT
/TXDEN
TXD
BLCSW
BLC
IC4TC7WT125FUF
5.0V Reg
IC609XC6221D501G-G
54M 50M
PTT_TXD
MIC_VBUS,ME,DM_KVL
SB
SB
1/2
IC4TC7WT125FUF
2/2
USB_D+
USB_D-
To L
CD
AS
SY
CN6
TXD
RXD
DAT[1]~DAT[7],/CS,/RD,/WR,A[23]
32M
54M
32M
18M
18M
SW/LCDRSTRSTB
To
FLE
X P
.BO
AR
D
CN3
IO
EXPANDER
/LCDRST
I2CCK,I2CDT,/KEYINT
/PSW
S1~S10
KEYILLUMINATIONLCD
BACKLIGHT
D3-D6,D11,D12,D17,D18,D33,D34B30-2365-05D9,D10,D15,D16
NSSW206C-T865
RGB LED
D20B30-2364-05
DCSWSSM6N37FE
Q2KEYBLC
SSM6N37FEQ8
LCDBLC1DCSW
DCSW LCDBLC2
54M54M
LED_R
LTC014EEBFS8
Q6
DCSW
LED_GDCSW
DCSWLED_B
54M
Q4
Q3
P_TEMP
/PSW
LCDBLC1
LED_B
LED_G
LED_R
KEYBLC
LCDBLC2
BLC
BLCSW
BUSSW
/TXDEN
32M
CN5
To SPEAKER
SP+
SPG
R_SET0
R_SET2
IC6TC35894FG
Q1SSM3K15AMFV
/PTT
Sub (Display) Unit (XC3-050)
SUB UNIT
MEMO
(No.RA054<Rev.001>) 2-20
PARTS LIST
[NX-3720H(G), NX-3720H, NX-3720(G), NX-3720,
NX-3820H(G), NX-3820H, NX-3820(G), NX-3820]
* SAFETY PRECAUTION
Parts identified by the � symbol are critical for safety. Replace only with
specified part numbers.
* BEWARE OF BOGUS PARTS
Parts that do not meet specifications may cause trouble in regard to safety and
performance. We recommend that genuine parts be used.
* (x_) in a description column shows the number of the used part.
- Contents -
Exploded view of general assembly and parts list
Electrical parts list
Packing materials and accessories parts list
3-2
3-4
3-21
(No.RA054<Rev.001>)3-1
Exploded view of general assembly and parts listBlock No.M1MM
12
29
1
34
5
6
9
8
10
11
13
14
15
16
17
19
20
2122
2324
25
26
27
28
30
31 32
33
34
35
36
37
38
16
41
42
43
7
A
A
A
A
B
B
B
BB
B
B
B
B
44
C
C
SUB UNIT<03>
TX-RX UNIT<01><02>
(GPS type)
(W/O
GPS type)
(K,K2 type)
(E type)
B
MODULE UNIT<04>
3-2(No.RA054<Rev.001>)
General assemblyBlock No. [M][1][M][M]
Symbol No. Part No. Part Name Description Local
1 A0C-0166-00 PLASTIC CABINET 3 A6C-0067-10 PANEL ASSY 4 B4D-0044-00 KENWOOD BADGE PANEL 5 B09-0732-03 CAP DSUB 6 B1B-0101-00 ILL.GUIDE LCD 7 B1B-0102-00 OPTI.DIFFUSER UPPER ILL-GUIDE 8 B1B-0103-00 REF.SHEET LOWER ILL-GUIDE 9 B3H-0058-00 LCD ASSY 304X100 DOT 10 E04-0454-15 C.RECEPTACLE-BN ANT BNC 3720E,3720GE,3820E,3820GE 10 E04-0167-15 C.RECEPTACLE-M ANT M 3720HGK,3720HK,3820HGK,3820HGK2,3820HK,3820HK2 11 E30-7684-35 DC CORD RADIO 12 E3A-0390-00 CORD W.CON. SP 13 E3G-0042-00 FFC WIRE 60P 14 F10-3112-13 SHIELDING CASE PM 15 F1A-0027-00 SHIELDING PLATE TOP 16 F1B-0086-00 SHIELDING COVER BLS(DCDC,VCO)(x2) 17 F1E-0040-00 SHADE TX-BUSY 19 G11-4578-04 SHEET W/O GPS 3720E,3720HK,3820E,3820HK,3820HK2 20 G11-4611-04 SHEET DSUB 21 G13-1837-04 CUSHION TOP SHIELD 22 G13-2101-14 CONDUCT CUSHION PM 23 G1D-0191-00 CUSHION LCD 24 G53-1643-04 PACKING DC CORD 25 G53-1675-04 PACKING ANT BNC 3720E,3720GE,3820E,3820GE 25 G53-1662-04 PACKING ANT M 3720HGK,3720HK,3820HGK,3820HGK2,3820HK,3820HK2 26 G53-1820-03 PACKING FRONT 27 G5D-0117-00 PACKING TOP 28 G5D-0127-00 PACKING SP 29 J1K-0456-00 HOLDER DISP PCB 30 J2B-0341-00 MOUNTING LCD 31 K2K-0242-00 KEY TOP 32 T07-0757-35 SPEAKER 6OHM/5.5W/7W 33 W09-0971-05 LITHIUM CELL 34 B09-0754-05 CAP SMA 3720GE,3720HGK,3820GE,3820HGK,3820HGK2 35 E0E-0003-00 C.RECEPTACLE-SM SMA 3720GE,3720HGK,3820GE,3820HGK,3820HGK2 36 E3F-0017-10 FLAT CABLE 20P BT/GPS 3720GE,3720HGK,3820GE,3820HGK,3820HGK2 37 F10-3225-05 SHIELDING COVER BLS(BT/GPS) 3720GE,3720HGK,3820GE,3820HGK,3820HGK2 38 G53-1768-04 PACKING SMA 3720GE,3720HGK,3820GE,3820HGK,3820HGK2 41 J8C-0018-00 FLEX P.BOARD KEY 42 B41-1837-04 CAUTION STICKER HOT SURFACE 43 B4B-0008-00 CAUTION STICKER FCC(PANEL) 3720HGK,3720HK,3820HGK,3820HGK2,3820HK,3820HK2 44 G0B-0104-00 EARTH SPRING PANEL HOLDER A N67-3010-48 P.H.SEMS SCREW PM,AMP,DC(GND)(x5) B N87-2608-48 BR.HEAD T.SCREW PCB,ANT,SMA(x17) 3720E,3720HK,3820E,3820HK,3820HK2 B N87-2608-48 BR.HEAD T.SCREW PCB,ANT,SMA(x19) 3720GE,3720HGK,3820GE,3820HGK,3820HGK2 C N83-2005-48 P.HEAD T.SCREW BT/GPS(x3) 3720GE,3720HGK,3820GE,3820HGK,3820HGK2- XC3-050M-00 SUB UNIT DISPLAY- XC2-0040-10 MODULE UNIT BT/GPS 3720GE,3720HGK,3820GE,3820HGK,3820HGK2- XCA-033K-00 TX-RX UNIT SERVICE UNIT 3720HGK,3720HK- XCA-033E-01 TX-RX UNIT SERVICE UNIT 3720E,3720GE- XCA-034E-01 TX-RX UNIT SERVICE UNIT 3820E,3820GE- XCA-034K-00 TX-RX UNIT SERVICE UNIT 3820HGK,3820HK- XCA-034K-01 TX-RX UNIT SERVICE UNIT 3820HGK2,3820HK2
(No.RA054<Rev.001>)3-3
Electrical parts listTX-RX UNIT
XC1-182K-00 (NX-3720E,NX-3720GE,NX-3720HGK,NX-3720HK)*Note : This part cannot be replaced.Therefore, this part is not supplied as a service part.
Block No. [0][1]
Symbol No. Part No. Part Name Description Local
IC1 BA00DD0WHFP ICIC12 LXDC2HN18F163 ICIC13 BU31TD2WNVX ICIC14 TPS61041DRVR ICIC15 XC6215B122N-G ICIC16 XC6209B502P-G ICIC17 NJM2878F4-32 ICIC18 XC61CN5002N-G ICIC19 XC6223D321G-G ICIC20 XC6223D321P-G ICIC21 XC8102AA07-G ICIC22 MSP430G2533P0 ICIC23 XC6221D501G-G ICIC24 LXDC2XQ12A-252 ICIC25 MP2560DQ-LF-Z ICIC26 XC6221D501G-G ICIC101 NJM2904CRB1 ICIC202 BGU6104 ICIC203 BA3472FVM ICIC205 AD8315ARM ICIC301 NJG1608KB2 ICIC302 AK2401 ICIC401 ------------ IC *NoteIC402 ------------ IC *NoteIC403 TC7SZ08FE ICIC404 ------------ IC *NoteIC405 BD11600NUX ICIC406 BD11600NUX ICIC407 TC7SET125FUF ICIC408 TC7SZ08FE ICIC409 TCA9555RTWR ICIC410 ADS7961SRHB ICIC411 DAC124S085CIS ICIC412 R2A20178NP ICIC413 XC61CN5002N-G ICIC414 BU7462NUX ICIC602 TC7WT126FU-F ICIC603 TC7WH126FK ICIC604 TCA9555RTWR ICIC605 ADM3202ARUZ ICIC606 TC7SET125FUF ICIC607 TLV32AIC3104I ICIC608 BU7462NUX ICIC609 XC6221D501G-G IC
Q11 LTC014EEBFS8 DIGI TRANSISTORQ12 TPCP8107-F FETQ13 LTC014EEBFS8 DIGI TRANSISTORQ14 LTC014TEBFS8 DIGI TRANSISTORQ15 LSCR523EBFS8 TRANSISTORQ16 LSAR523UBFS8 TRANSISTORQ17 TPCP8107-F FETQ18 LTC014EEBFS8 DIGI TRANSISTORQ19 VT6M1 FETQ20 SSM3J334R FETQ21 LTC014EEBFS8 DIGI TRANSISTORQ22 SSM3J334R FETQ23 LTC014EEBFS8 DIGI TRANSISTORQ25 EMD9 DIGI TRANSISTORQ103 EM6M2 FETQ104 2SD2654/W/ TRANSISTORQ105 MCH3914-H/8/ FETQ106 2SC5108FT/Y/ TRANSISTORQ107 2SC5108FT/Y/ TRANSISTORQ201 RFM01U7PF FETQ202 LSCR523EBFS8 TRANSISTOR
Q204 LSCR523EBFS8 TRANSISTORQ205 EMD9 DIGI TRANSISTORQ206 VT6M1 FETQ301 SSM3K15AMFV FETQ401 2SC4617/S/ TRANSISTORQ402 SSM3K15AMFV FETQ403 SSM3K15AMFV FETQ404 LTC014TEBFS8 DIGI TRANSISTORQ601 SSM6N15AFEM DUAL FETQ602 LTC014TEBFS8 DIGI TRANSISTORQ603 TPCP8107-F FETQ604 LTC014TEBFS8 DIGI TRANSISTORQ605 SSM6N15AFEM DUAL FETQ606 SSM3J334R FET
D1 ST70-27F-572 ZENER DIODED13 EDZV5.6B ZENER DIODED14 RB521CM-30 DIODED15 1SS400SM DIODED16 RB060M-40 DIODED17 RB561VM-40 SCHOTTKY DIODED18 RB521CM-30 DIODED19 RB521CM-30 DIODED20 EDZV18B ZENER DIODED21 RB520SM-30 DIODED22 EDZV8.2B ZENER DIODED24 RB520SM-30 DIODED26 RB521CM-30 DIODED27 RB521CM-30 DIODED101 EDZV8.2B ZENER DIODED102 SMV1270-079LF VARI CAP DIODED103 1SV282-F VARI CAP DIODED104 1SV282-F VARI CAP DIODED105 1SV282-F VARI CAP DIODED106 1SV282-F VARI CAP DIODED107 1SS400SM DIODED108 SMV1130-079LF VARI CAP DIODED201 EDZV5.6B ZENER DIODED202 RN142S DIODED204 RB706F-40 DIODED205 L8104 DIODED206 L8104 DIODED207 L8104 DIODED208 RN142S DIODED209 RN142S DIODED301 1SS390 DIODED302 1SS390 DIODED303 1SS400SM DIODED304 1SS400SM DIODED401 RB521CM-30 DIODED402 SPC10501A01 VARISTORD403 SPC10501A01 VARISTORD404 SPC10501A01 VARISTORD405 SPC10501A01 VARISTORD406 SPC10501A01 VARISTORD407 EDZV8.2B ZENER DIODED408 RB521CM-30 DIODED409 RB521CM-30 DIODED410 RB521CM-30 DIODED601 EDZV5.6B ZENER DIODED602 RB521CM-30 DIODED603 EDZV6.8B ZENER DIODED604 EDZV6.8B ZENER DIODED605 EDZV6.8B ZENER DIODED606 EDZV6.8B ZENER DIODED607 EDZV6.8B ZENER DIODED608 EDZV6.8B ZENER DIODED609 RB521CM-30 DIODED610 RB521CM-30 DIODED611 EDZV6.8B ZENER DIODED612 DA204U MULTIPLE DIODED613 DA204U MULTIPLE DIODED614 RB521CM-30 DIODED615 RB521CM-30 DIODED616 AVRM10270K101 VARISTORD617 AVRM10270K101 VARISTOR
Symbol No. Part No. Part Name Description Local
3-4(No.RA054<Rev.001>)
D618 RB520SM-30 DIODED619 RB521CM-30 DIODE
C1 C92-0968-05 E CAPACITOR 470uF 25VC2 C92-0906-05 E CAPACITOR 330uF 10VC3 C92-0906-05 E CAPACITOR 330uF 10VC4 CE32BY1E470M E CAPACITOR 47uF 25V MC5 C92-0968-05 E CAPACITOR 470uF 25VC11 CK73HB1E104K C CAPACITOR 0.10uF 25V KC12 CK73HBB1H102K C CAPACITOR 1000pF 50V KC14 CK73FB1C106K C CAPACITOR 10uF 16V KC15 CK73HB1E104K C CAPACITOR 0.10uF 25V KC16 C93-1959-05 C CAPACITOR 0.1uF 16VC17 CK73HB1A474K C CAPACITOR 0.47uF 10V KC18 CK73HB1C105K C CAPACITOR 1.0uF 16V KC19 CK73HB1H103K C CAPACITOR 10000pF 50V KC20 CK73HBB1H471K C CAPACITOR 470pF 50V KC21 CK73HBB1H471K C CAPACITOR 470pF 50V KC22 CK73HBB1H471K C CAPACITOR 470pF 50V KC24 CK73HB1C105K C CAPACITOR 1.0uF 16V KC25 CK73HBB1H102K C CAPACITOR 1000pF 50V KC26 CC73HCH1H101J C CAPACITOR 100pF 50V JC27 CK73HBB1H102K C CAPACITOR 1000pF 50V KC28 CK73GB1H105K C CAPACITOR 1uF 50V KC29 CK73HBB1H222K C CAPACITOR 2200pF 50V KC30 CK73EB1H475KM C CAPACITOR 4.7uF 50V MC31 CK73HB1C105K C CAPACITOR 1.0uF 16V KC32 CK73EB1H475KM C CAPACITOR 4.7uF 50V MC33 CK73GB1H105K C CAPACITOR 1uF 50V KC34 CK73EB1H475KM C CAPACITOR 4.7uF 50V MC35 CK73HB1E104K C CAPACITOR 0.10uF 25V KC36 CK73HBB1H471K C CAPACITOR 470pF 50V KC37 CK73GB1H105K C CAPACITOR 1uF 50V KC38 CK73FB1C106K C CAPACITOR 10uF 16V KC39 CK73HBB1H471K C CAPACITOR 470pF 50V KC40 CK73GB0J106K C CAPACITOR 10uF 6.3V KC41 CK73GB1H105K C CAPACITOR 1uF 50V KC42 CK73HBB1H471K C CAPACITOR 470pF 50V KC43 CK73HB1C105K C CAPACITOR 1.0uF 16V KC44 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC45 CK73HB1E104K C CAPACITOR 0.10uF 25V KC46 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC47 CK73HBB1H102K C CAPACITOR 1000pF 50V KC48 CC73HCH1H101J C CAPACITOR 100pF 50V JC49 CK73HB1E104K C CAPACITOR 0.10uF 25V KC50 CK73GB1H105K C CAPACITOR 1uF 50V KC51 CK73HBB1H471K C CAPACITOR 470pF 50V KC52 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC53 CK73FB1C106K C CAPACITOR 10uF 16V KC54 CK73FB1C106K C CAPACITOR 10uF 16V KC55 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC56 CK73HBB1H102K C CAPACITOR 1000pF 50V KC57 CK73GB0J106K C CAPACITOR 10uF 6.3V KC58 CK73FB1C106K C CAPACITOR 10uF 16V KC59 CK73FB1C106K C CAPACITOR 10uF 16V KC60 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC61 CK73HB1H391K C CAPACITOR 390pF 50V KC62 CK73HB1H391K C CAPACITOR 390pF 50V KC63 CK730FA1H475K C CAPACITOR 4.7uF 50V KC64 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC65 CK730DT1C476K C CAPACITOR 47uF 16V KC66 CK73HB1E104K C CAPACITOR 0.10uF 25V KC67 CC73HCH1H470G C CAPACITOR 47pF 50V GC68 CK73HB1C105K C CAPACITOR 1.0uF 16V KC69 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC72 CK73HB1C105K C CAPACITOR 1.0uF 16V KC73 CK73HB1C105K C CAPACITOR 1.0uF 16V KC74 CK73HB1E104K C CAPACITOR 0.10uF 25V KC75 CK73HB1E473K C CAPACITOR 0.047uF 25V KC76 CK73HB1C105K C CAPACITOR 1.0uF 16V KC108 CK73HB1H103K C CAPACITOR 10000pF 50V KC109 CC73HCH1H330G C CAPACITOR 33pF 50V GC110 CC73HCH1H101J C CAPACITOR 100pF 50V JC111 CK73GB1H105K C CAPACITOR 1uF 50V KC112 CC73HCH1H101J C CAPACITOR 100pF 50V JC113 CK73FBB1H154K C CAPACITOR 0.15uF 50V KC114 CS77ABE1D100M TA E CAPACITOR 10uF 20V MC115 CK73FB1H473K C CAPACITOR 0.047uF 50V K
Symbol No. Part No. Part Name Description Local
C116 CC730AD1H104J C CAPACITOR 0.1uF 50V JC120 CC73HCH1H101J C CAPACITOR 100pF 50V JC123 CC73HCH1H221J C CAPACITOR 220pF 50V JC124 CK73HBB1H471K C CAPACITOR 470pF 50V KC125 CC73HCH1H101J C CAPACITOR 100pF 50V JC127 CC73HCH1H221J C CAPACITOR 220pF 50V JC128 CC73HCH1H020B C CAPACITOR 2pF 50V BC129 CC73HCH1HR75B C CAPACITOR 0.75pF 50V BC130 CK73FB1C106K C CAPACITOR 10uF 16V KC131 CC73HCH1H090B C CAPACITOR 9pF 50V BC132 CC73HCH1H090B C CAPACITOR 9pF 50V BC133 CC73HCH1H070B C CAPACITOR 7pF 50V BC134 CK73HBB1H471K C CAPACITOR 470pF 50V KC135 CC73HCH1H0R5B C CAPACITOR 0.5pF 50V BC136 CK73HBB1H471K C CAPACITOR 470pF 50V KC137 CC73HCH1H060B C CAPACITOR 6pF 50V BC138 CK73HBB1H471K C CAPACITOR 470pF 50V KC139 CC73HCH1H060B C CAPACITOR 6pF 50V BC140 CC73HCH1H1R5B C CAPACITOR 1.5pF 50V BC141 CC73HCH1H120G C CAPACITOR 12pF 50V GC142 CC73HCH1H1R5B C CAPACITOR 1.5pF 50V BC143 CC73HCH1H060B C CAPACITOR 6pF 50V BC145 CK73HBB1H102K C CAPACITOR 1000pF 50V KC146 CK73HBB1H471K C CAPACITOR 470pF 50V KC147 CK73HBB1H471K C CAPACITOR 470pF 50V KC148 CC73HCH1H040B C CAPACITOR 4pF 50V BC207 C93-1861-05 C CAPACITOR 10pF 250VC208 C93-1852-05 C CAPACITOR 6pF 250VC209 C93-1852-05 C CAPACITOR 6pF 250VC211 CK73HB1C105K C CAPACITOR 1.0uF 16V KC212 CK73HBB1H471K C CAPACITOR 470pF 50V KC213 CC73HCH1H220G C CAPACITOR 22pF 50V GC214 CK73HB1H103K C CAPACITOR 10000pF 50V KC216 CK73HBB1H102K C CAPACITOR 1000pF 50V KC218 CC73HCH1H680J C CAPACITOR 68pF 50V JC219 C93-1849-05 C CAPACITOR 5pF 250VC220 CK73HBB1H102K C CAPACITOR 1000pF 50V KC221 CK73HB1E473K C CAPACITOR 0.047uF 25V KC222 CK73HBB1H152K C CAPACITOR 1500pF 50V KC223 CC73HCH1H101J C CAPACITOR 100pF 50V JC224 CC73HCH1H470G C CAPACITOR 47pF 50V GC225 CK73HBB1H102K C CAPACITOR 1000pF 50V KC226 CC73HCH1H220G C CAPACITOR 22pF 50V GC227 CC73HCH1H390G C CAPACITOR 39pF 50V GC228 CC73HCH1H220G C CAPACITOR 22pF 50V GC229 CC73HCH1H120G C CAPACITOR 12pF 50V GC230 CK73HBB1H102K C CAPACITOR 1000pF 50V KC231 CC73HCH1H101J C CAPACITOR 100pF 50V JC232 CK73HBB1H102K C CAPACITOR 1000pF 50V KC233 CK73HBB1H102K C CAPACITOR 1000pF 50V KC234 CC73GCH1H330J C CAPACITOR 33pF 50V JC235 CK73HB1H103K C CAPACITOR 10000pF 50V KC236 CC73HCH1H101J C CAPACITOR 100pF 50V JC237 CK73HBB1H102K C CAPACITOR 1000pF 50V KC238 CK73GBB1H102K C CAPACITOR 1000pF 50V KC239 CK73HBB1H472K C CAPACITOR 4700pF 50V KC241 CK73GBB1H102K C CAPACITOR 1000pF 50V KC242 CC73HCH1H220G C CAPACITOR 22pF 50V GC243 CC73HCH1H470G C CAPACITOR 47pF 50V GC244 CC73HCH1H101J C CAPACITOR 100pF 50V JC245 CK73HBB1H102K C CAPACITOR 1000pF 50V KC247 CC73HCH1H101J C CAPACITOR 100pF 50V JC249 CC73HCH1H101J C CAPACITOR 100pF 50V JC250 C93-1900-05 C CAPACITOR 1000pF 630VC251 CK73GBB1H332K C CAPACITOR 3300pF 50V KC252 CK73HB1E104K C CAPACITOR 0.10uF 25V KC253 CC73GCH1H3R5B C CAPACITOR 3.5pF 50V BC254 CK73GBB1H102K C CAPACITOR 1000pF 50V KC255 CK73GBB1H102K C CAPACITOR 1000pF 50V KC256 C93-1900-05 C CAPACITOR 1000pF 630VC257 CK73GBB1H102K C CAPACITOR 1000pF 50V KC258 CK73GBB1H102K C CAPACITOR 1000pF 50V KC259 C93-1846-05 C CAPACITOR 4pF 250VC260 CK73HB1E104K C CAPACITOR 0.10uF 25V KC261 CC73GCH1H120G C CAPACITOR 12pF 50V GC262 C93-1887-05 C CAPACITOR 82pF 630VC263 CK73HBB1H472K C CAPACITOR 4700pF 50V KC264 C93-2041-05 C CAPACITOR 11pF 500V
Symbol No. Part No. Part Name Description Local
(No.RA054<Rev.001>)3-5
C265 C93-1852-05 C CAPACITOR 6pF 250VC266 CK73HBB1H102K C CAPACITOR 1000pF 50V KC267 C93-2035-05 C CAPACITOR 9pF 500VC268 C93-1852-05 C CAPACITOR 6pF 250VC270 CK73HBB1H102K C CAPACITOR 1000pF 50V KC271 CK73HBB1H102K C CAPACITOR 1000pF 50V KC272 CK73HBB1H102K C CAPACITOR 1000pF 50V KC274 CC73GCH1H150G C CAPACITOR 15pF 50V GC275 CC73GCH1H390J C CAPACITOR 39pF 50V JC277 C93-2041-05 C CAPACITOR 11pF 500VC278 C93-2031-05 C CAPACITOR 8pF 500VC279 C93-1852-05 C CAPACITOR 6pF 250VC280 C93-1838-05 C CAPACITOR 2pF 250VC304 CC73JCH1H101J C CAPACITOR 100pF 50V JC305 CC73JCH1H101J C CAPACITOR 100pF 50V JC306 CK73HBB1H102K C CAPACITOR 1000pF 50V KC307 CC73HCH1H070B C CAPACITOR 7pF 50V BC308 CC73HCH1H270J C CAPACITOR 27pF 50V JC309 CC73HCH1H120G C CAPACITOR 12pF 50V GC310 CC73HCH1H270J C CAPACITOR 27pF 50V JC311 CC73HCH1H150G C CAPACITOR 15pF 50V GC312 CC73HCH1H120G C CAPACITOR 12pF 50V GC313 CK73HBB1H102K C CAPACITOR 1000pF 50V KC314 CK73HB1H103K C CAPACITOR 10000pF 50V KC315 CK73HB1C105K C CAPACITOR 1.0uF 16V KC316 CK73HB1C105K C CAPACITOR 1.0uF 16V KC317 CC73HCH1H030B C CAPACITOR 3pF 50V BC318 CC73HCH1H050B C CAPACITOR 5pF 50V BC319 CC73HCH1H050B C CAPACITOR 5pF 50V BC320 CC73HCH1H390G C CAPACITOR 39pF 50V GC321 CK730BS0J106M C CAPACITOR 10uF 6.3V MC322 CC73HCH1H101J C CAPACITOR 100pF 50V JC323 CC73HCH1H101J C CAPACITOR 100pF 50V JC324 CK73HB1H103K C CAPACITOR 10000pF 50V KC325 CC73HCH1H101J C CAPACITOR 100pF 50V JC326 CC73HCH1H101J C CAPACITOR 100pF 50V JC327 CK73HB1C105K C CAPACITOR 1.0uF 16V KC328 CK73HB1E104K C CAPACITOR 0.10uF 25V KC329 CC73HCH1H101J C CAPACITOR 100pF 50V JC330 CK73HB1E104K C CAPACITOR 0.10uF 25V KC331 CK73HBB1H102K C CAPACITOR 1000pF 50V KC332 CC73HCH1H101J C CAPACITOR 100pF 50V JC333 CK73HBB1H471K C CAPACITOR 470pF 50V KC334 CC73HCH1H070B C CAPACITOR 7pF 50V BC335 CC73HCH1H101J C CAPACITOR 100pF 50V JC336 CK73HB1E104K C CAPACITOR 0.10uF 25V KC337 CK73HBB1H102K C CAPACITOR 1000pF 50V KC338 CK73HBB1H102K C CAPACITOR 1000pF 50V KC339 CC73HCH1H120G C CAPACITOR 12pF 50V GC340 CK73HB1E104K C CAPACITOR 0.10uF 25V KC341 CK73HBB1H102K C CAPACITOR 1000pF 50V KC342 CK73HB0J225K C CAPACITOR 2.2uF 6.3V KC343 CC73HCH1H101J C CAPACITOR 100pF 50V JC344 CK730BS0J106M C CAPACITOR 10uF 6.3V MC345 CK73HB1A474K C CAPACITOR 0.47uF 10V KC346 CK730BS0J106M C CAPACITOR 10uF 6.3V MC347 CK73HB1E104K C CAPACITOR 0.10uF 25V KC348 CK73HB1E104K C CAPACITOR 0.10uF 25V KC405 CK73HBB1H472K C CAPACITOR 4700pF 50V KC410 CK73HBB1H102K C CAPACITOR 1000pF 50V KC411 CK73HBB1H102K C CAPACITOR 1000pF 50V KC412 CK73HB1H103K C CAPACITOR 10000pF 50V KC414 CK73HB1C105K C CAPACITOR 1.0uF 16V KC415 C93-1959-05 C CAPACITOR 0.1uF 16VC416 C93-1959-05 C CAPACITOR 0.1uF 16VC417 CK73FXR0J226M C CAPACITOR 22uF 6.3V MC418 CK73HB1H103K C CAPACITOR 10000pF 50V KC419 C93-1959-05 C CAPACITOR 0.1uF 16VC420 C93-1959-05 C CAPACITOR 0.1uF 16VC421 CK73FXR0J226M C CAPACITOR 22uF 6.3V MC422 CK73GB0J106K C CAPACITOR 10uF 6.3V KC423 C93-1959-05 C CAPACITOR 0.1uF 16VC424 C93-1959-05 C CAPACITOR 0.1uF 16VC425 C93-1959-05 C CAPACITOR 0.1uF 16VC426 C93-1959-05 C CAPACITOR 0.1uF 16VC427 C93-1959-05 C CAPACITOR 0.1uF 16VC428 C93-1959-05 C CAPACITOR 0.1uF 16VC429 C93-1959-05 C CAPACITOR 0.1uF 16V
Symbol No. Part No. Part Name Description Local
C430 C93-1959-05 C CAPACITOR 0.1uF 16VC431 C93-1959-05 C CAPACITOR 0.1uF 16VC432 C93-1959-05 C CAPACITOR 0.1uF 16VC433 CC73JCH1H101J C CAPACITOR 100pF 50V JC434 C93-1959-05 C CAPACITOR 0.1uF 16VC435 C93-1959-05 C CAPACITOR 0.1uF 16VC436 CK73HB1H103K C CAPACITOR 10000pF 50V KC437 CK73GB0J106K C CAPACITOR 10uF 6.3V KC438 CK73HB1H103K C CAPACITOR 10000pF 50V KC439 CK73GB0J106K C CAPACITOR 10uF 6.3V KC440 C93-1959-05 C CAPACITOR 0.1uF 16VC441 C93-1959-05 C CAPACITOR 0.1uF 16VC442 C93-1959-05 C CAPACITOR 0.1uF 16VC443 C93-1959-05 C CAPACITOR 0.1uF 16VC444 C93-1959-05 C CAPACITOR 0.1uF 16VC445 CC73JCH1H101J C CAPACITOR 100pF 50V JC446 CK73GB0J106K C CAPACITOR 10uF 6.3V KC447 CK73HB1H103K C CAPACITOR 10000pF 50V KC448 C93-1959-05 C CAPACITOR 0.1uF 16VC449 CK73GB0J106K C CAPACITOR 10uF 6.3V KC450 CK73HB1H103K C CAPACITOR 10000pF 50V KC451 C93-1959-05 C CAPACITOR 0.1uF 16VC452 CK73GB0J106K C CAPACITOR 10uF 6.3V KC453 CK73GB0J106K C CAPACITOR 10uF 6.3V KC454 CC73HCH1H050B C CAPACITOR 5pF 50V BC455 C93-1959-05 C CAPACITOR 0.1uF 16VC456 CK73GB0J106K C CAPACITOR 10uF 6.3V KC457 C93-1959-05 C CAPACITOR 0.1uF 16VC458 C93-1959-05 C CAPACITOR 0.1uF 16VC459 C93-1959-05 C CAPACITOR 0.1uF 16VC460 C93-1959-05 C CAPACITOR 0.1uF 16VC461 C93-1959-05 C CAPACITOR 0.1uF 16VC462 CK73HB1C105K C CAPACITOR 1.0uF 16V KC463 C93-1959-05 C CAPACITOR 0.1uF 16VC464 C93-1959-05 C CAPACITOR 0.1uF 16VC465 C93-1959-05 C CAPACITOR 0.1uF 16VC466 C93-1959-05 C CAPACITOR 0.1uF 16VC467 C93-1959-05 C CAPACITOR 0.1uF 16VC468 C93-1959-05 C CAPACITOR 0.1uF 16VC469 C93-1959-05 C CAPACITOR 0.1uF 16VC470 C93-1959-05 C CAPACITOR 0.1uF 16VC471 C93-1959-05 C CAPACITOR 0.1uF 16VC472 C93-1959-05 C CAPACITOR 0.1uF 16VC473 C93-1959-05 C CAPACITOR 0.1uF 16VC474 C93-1959-05 C CAPACITOR 0.1uF 16VC475 C93-1959-05 C CAPACITOR 0.1uF 16VC476 C93-1959-05 C CAPACITOR 0.1uF 16VC477 C93-1959-05 C CAPACITOR 0.1uF 16VC478 CK73HB1C105K C CAPACITOR 1.0uF 16V KC479 C93-1959-05 C CAPACITOR 0.1uF 16VC480 CC73HCH1H180G C CAPACITOR 18pF 50V GC481 CC73HCH1H150G C CAPACITOR 15pF 50V GC482 CK73HB1E104K C CAPACITOR 0.10uF 25V KC483 CK73HB1A224K C CAPACITOR 0.22uF 10V KC484 CK73HBB1H102K C CAPACITOR 1000pF 50V KC485 C93-1959-05 C CAPACITOR 0.1uF 16VC486 C93-1959-05 C CAPACITOR 0.1uF 16VC487 CK73HB1H103K C CAPACITOR 10000pF 50V KC488 CK73HB1H103K C CAPACITOR 10000pF 50V KC489 CK73GB1H105K C CAPACITOR 1uF 50V KC490 CK73HB1E104K C CAPACITOR 0.10uF 25V KC491 CK73HB1H103K C CAPACITOR 10000pF 50V KC492 CC73JCH1H101J C CAPACITOR 100pF 50V JC493 CK73HB1C105K C CAPACITOR 1.0uF 16V KC494 C93-1959-05 C CAPACITOR 0.1uF 16VC495 C93-1959-05 C CAPACITOR 0.1uF 16VC497 C93-1959-05 C CAPACITOR 0.1uF 16VC498 CK73HB1H103K C CAPACITOR 10000pF 50V KC501 CC73JCH1H101J C CAPACITOR 100pF 50V JC502 C93-1959-05 C CAPACITOR 0.1uF 16VC503 CC73JCH1H101J C CAPACITOR 100pF 50V JC504 CC73HCH1H101J C CAPACITOR 100pF 50V JC505 CC73JCH1H101J C CAPACITOR 100pF 50V JC506 CC73JCH1H101J C CAPACITOR 100pF 50V JC507 CC73JCH1H101J C CAPACITOR 100pF 50V JC509 CC73JCH1H101J C CAPACITOR 100pF 50V JC510 CK73HB1E104K C CAPACITOR 0.10uF 25V KC511 CK73HB1E104K C CAPACITOR 0.10uF 25V K
Symbol No. Part No. Part Name Description Local
3-6(No.RA054<Rev.001>)
C514 CK73HBB1H102K C CAPACITOR 1000pF 50V KC515 CK73HB1C105K C CAPACITOR 1.0uF 16V KC516 C93-1959-05 C CAPACITOR 0.1uF 16VC517 CK73HB1C105K C CAPACITOR 1.0uF 16V KC518 CC73HCH1H101J C CAPACITOR 100pF 50V JC519 CK73HB1E104K C CAPACITOR 0.10uF 25V KC520 CK73HB1E104K C CAPACITOR 0.10uF 25V KC521 CK73HB1E104K C CAPACITOR 0.10uF 25V KC522 CK73HB1H103K C CAPACITOR 10000pF 50V KC523 CK73HBB1H102K C CAPACITOR 1000pF 50V KC524 CC73HCH1H470G C CAPACITOR 47pF 50V GC525 CC73HCH1H470G C CAPACITOR 47pF 50V GC526 CK73HB1C105K C CAPACITOR 1.0uF 16V KC527 CK73HB1E104K C CAPACITOR 0.10uF 25V KC528 CK73HB1C105K C CAPACITOR 1.0uF 16V KC605 CK73HB1H103K C CAPACITOR 10000pF 50V KC606 CK73HB1H103K C CAPACITOR 10000pF 50V KC607 C93-1959-05 C CAPACITOR 0.1uF 16VC608 CK73HB1H103K C CAPACITOR 10000pF 50V KC609 CK73GB1H105K C CAPACITOR 1uF 50V KC610 CK73GB1H105K C CAPACITOR 1uF 50V KC611 CK73GB1H105K C CAPACITOR 1uF 50V KC612 CK73GB1H105K C CAPACITOR 1uF 50V KC613 CK73HBB1H102K C CAPACITOR 1000pF 50V KC614 CC73HCH1H101J C CAPACITOR 100pF 50V JC615 CC73HCH1H101J C CAPACITOR 100pF 50V JC616 CC73HCH1H101J C CAPACITOR 100pF 50V JC617 CC73HCH1H101J C CAPACITOR 100pF 50V JC618 CC73HCH1H101J C CAPACITOR 100pF 50V JC619 CC73HCH1H101J C CAPACITOR 100pF 50V JC620 CC73HCH1H101J C CAPACITOR 100pF 50V JC621 CK73HBB1E223K C CAPACITOR 0.022uF 25V KC622 CC73HCH1H101J C CAPACITOR 100pF 50V JC623 CC73HCH1H101J C CAPACITOR 100pF 50V JC624 CC73HCH1H101J C CAPACITOR 100pF 50V JC625 CC73HCH1H101J C CAPACITOR 100pF 50V JC626 CK73GB1H105K C CAPACITOR 1uF 50V KC627 CK73HB1A224K C CAPACITOR 0.22uF 10V KC628 CK73HB1A224K C CAPACITOR 0.22uF 10V KC629 CK73HBB1H102K C CAPACITOR 1000pF 50V KC630 CK73HBB1H102K C CAPACITOR 1000pF 50V KC631 CK73GB1H105K C CAPACITOR 1uF 50V KC632 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC633 C93-1959-05 C CAPACITOR 0.1uF 16VC634 C93-1959-05 C CAPACITOR 0.1uF 16VC635 CK73HB1H103K C CAPACITOR 10000pF 50V KC636 CK73GB0J106K C CAPACITOR 10uF 6.3V KC637 CK73GB0J106K C CAPACITOR 10uF 6.3V KC638 C93-1959-05 C CAPACITOR 0.1uF 16VC639 CK73HB1C105K C CAPACITOR 1.0uF 16V KC640 C93-1959-05 C CAPACITOR 0.1uF 16VC641 C93-1959-05 C CAPACITOR 0.1uF 16VC642 C93-1959-05 C CAPACITOR 0.1uF 16VC643 C93-1959-05 C CAPACITOR 0.1uF 16VC644 C93-1959-05 C CAPACITOR 0.1uF 16VC645 CK73HB1E104K C CAPACITOR 0.10uF 25V KC646 CK73GB0J106K C CAPACITOR 10uF 6.3V KC647 CK73HB1C105K C CAPACITOR 1.0uF 16V KC648 C93-1959-05 C CAPACITOR 0.1uF 16VC649 CK73HB1C105K C CAPACITOR 1.0uF 16V KC650 C93-1959-05 C CAPACITOR 0.1uF 16VC651 CC73JCH1H101J C CAPACITOR 100pF 50V JC652 CK73HB1C105K C CAPACITOR 1.0uF 16V KC653 CK73HBB1E223K C CAPACITOR 0.022uF 25V KC655 CK73HB1C105K C CAPACITOR 1.0uF 16V KC656 CK73GB0J106K C CAPACITOR 10uF 6.3V KC657 CK73HB1E104K C CAPACITOR 0.10uF 25V KC658 CC73HCH1H680J C CAPACITOR 68pF 50V JC659 CK73HB1C105K C CAPACITOR 1.0uF 16V KC660 CK73HBB1H102K C CAPACITOR 1000pF 50V KC661 CK73HB1C105K C CAPACITOR 1.0uF 16V KC663 CK73HBB1H471K C CAPACITOR 470pF 50V KC664 CK73GB1H105K C CAPACITOR 1uF 50V KC665 CK73GXR1C225K C CAPACITOR 2.2uF 16V K
R2 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR5 R92-1061-05 C RESISTOR 0.008ΩR21 RK73HB1J104J MG RESISTOR 100kΩ 1/16W J
Symbol No. Part No. Part Name Description Local
R22 RK73HH1J104D MG RESISTOR 100kΩ 1/16W DR23 RK73HH1J104D MG RESISTOR 100kΩ 1/16W DR24 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR25 RK73HH1J104D MG RESISTOR 100kΩ 1/16W DR26 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR27 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR28 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR29 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR30 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR31 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR32 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR33 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR34 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR35 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR36 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR37 RK73JB1H472J MG RESISTOR 4.7kΩ 1/20W JR38 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR39 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR40 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR41 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR42 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR43 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR44 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR45 RK73HH1J473D MG RESISTOR 47kΩ 1/16W DR46 RK73HH1J113D MG RESISTOR 11kΩ 1/16W DR47 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR48 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR49 RK73HB1J224J MG RESISTOR 220kΩ 1/16W JR50 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR51 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR52 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR53 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR54 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR55 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR56 RK73HB1J124J MG RESISTOR 120kΩ 1/16W JR57 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR58 RK73HH1J303D MG RESISTOR 30kΩ 1/16W DR59 RK73HH1J154D MG RESISTOR 150kΩ 1/16W DR60 RK73HH1J113D MG RESISTOR 11kΩ 1/16W DR61 RK73HH1J103D MG RESISTOR 10kΩ 1/16W DR62 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR63 RK73HH1J113D MG RESISTOR 11kΩ 1/16W DR64 R92-3769-05 MG RESISTOR 10Ω 0.25WR65 R92-3769-05 MG RESISTOR 10Ω 0.25WR66 RK73HB1J334J MG RESISTOR 330kΩ 1/16W JR67 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR68 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR69 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR70 RK73HH1J273D MG RESISTOR 27kΩ 1/16W DR71 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR72 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR73 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR74 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR75 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR76 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR77 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR78 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR79 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR80 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR81 RK73FB2B2R7J MG RESISTOR 2.7Ω 1/8W JR82 RK73FB2B3R3J MG RESISTOR 3.3Ω 1/8W JR83 RK73HH1J152D MG RESISTOR 1.5kΩ 1/16W DR84 RK73HH1J472D MG RESISTOR 4.7kΩ 1/16W DR108 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR109 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR112 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR113 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR114 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR115 RK73HB1J124J MG RESISTOR 120kΩ 1/16W JR116 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR117 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR118 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR119 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR120 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR121 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR122 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR123 RK73HH1J391D MG RESISTOR 390Ω 1/16W DR124 RK73HB1J103J MG RESISTOR 10kΩ 1/16W J
Symbol No. Part No. Part Name Description Local
(No.RA054<Rev.001>)3-7
R125 RK73HB1J106J MG RESISTOR 10MΩ 1/16W JR127 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR128 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR131 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR132 RK73HB1J122J MG RESISTOR 1.2kΩ 1/16W JR133 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR134 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR135 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR136 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR137 RN73HH1J151D MG RESISTOR 150Ω 0.063W DR138 RN73HH1J100D MF RESISTOR 10Ω 0.063W DR139 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR140 RK73HB1J562J MG RESISTOR 5.6kΩ 1/16W JR141 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR142 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR143 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR144 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR145 RK73HB1J330J MG RESISTOR 33Ω 1/16W JR146 RK73HB1J822J MG RESISTOR 8.2kΩ 1/16W JR147 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR148 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR149 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR203 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR204 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR205 RK73GB2A181J MG RESISTOR 180Ω 1/10W JR206 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR207 RK73FB2B221J MG RESISTOR 220Ω 1/8W JR208 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR211 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR212 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR213 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR214 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR215 RK73HB1J390J MG RESISTOR 39Ω 1/16W JR216 RK73HB1J390J MG RESISTOR 39Ω 1/16W JR217 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR218 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR219 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR220 RK73HB1J121J MG RESISTOR 120Ω 1/16W JR221 RK73HB1J822J MG RESISTOR 8.2kΩ 1/16W JR222 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR223 RK73HB1J560J MG RESISTOR 56Ω 1/16W JR224 RK73HB1J560J MG RESISTOR 56Ω 1/16W JR225 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR226 RK73HB1J270J MG RESISTOR 27Ω 1/16W JR227 RK73HB1J332J MG RESISTOR 3.3kΩ 1/16W JR228 RK73HB1J562J MG RESISTOR 5.6kΩ 1/16W JR229 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR230 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR231 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR233 RK73GB2A121J MG RESISTOR 120Ω 1/10W JR235 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR238 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR239 RK73GB2A271J MG RESISTOR 270Ω 1/10W JR240 RK73GB2A390J MG RESISTOR 39Ω 1/10W JR241 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR242 RK73GB2A271J MG RESISTOR 270Ω 1/10W JR243 RK73GB2A390J MG RESISTOR 39Ω 1/10W JR244 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR245 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR247 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR248 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR250 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR251 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR256 RK73GB2A221J MG RESISTOR 220Ω 1/10W JR259 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR260 RK73HB1J124J MG RESISTOR 120kΩ 1/16W JR261 RK73GB2A471J MG RESISTOR 470Ω 1/10W JR262 RK73FB2B101J MG RESISTOR 100Ω 1/8W JR265 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR266 RK73HB1J274J MG RESISTOR 270kΩ 1/16W JR267 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR269 RK73FB2B121J MG RESISTOR 120Ω 1/8W JR270 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR271 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR272 RK73GB2A121J MG RESISTOR 120Ω 1/10W JR273 RK73HB1J183J MG RESISTOR 18kΩ 1/16W JR274 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR275 RK73HB1J223J MG RESISTOR 22kΩ 1/16W J
Symbol No. Part No. Part Name Description Local
R276 RK73PB2H560J MG RESISTOR 56Ω 1/2W JR277 RK73PB2H560J MG RESISTOR 56Ω 1/2W JR278 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR279 RK73HB1J560J MG RESISTOR 56Ω 1/16W JR280 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR282 RK73HB1J273J MG RESISTOR 27kΩ 1/16W JR302 RK73HB1J821J MG RESISTOR 820Ω 1/16W JR303 RK73HB1J821J MG RESISTOR 820Ω 1/16W JR304 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR305 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR307 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR308 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR309 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR310 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR311 RK73HH1J271D MG RESISTOR 270Ω 1/16W DR312 RK73HB1J5R6J MG RESISTOR 5.6Ω 1/16W JR313 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR314 RK73HB1J120J MG RESISTOR 12Ω 1/16W JR315 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR316 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR317 RK73HH1J473D MG RESISTOR 47kΩ 1/16W DR319 RK73HH1J273D MG RESISTOR 27kΩ 1/16W DR320 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR321 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR322 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR323 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR324 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR325 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR326 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR407 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR408 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR416 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR418 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR420 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR421 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR422 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR423 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR424 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR425 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR426 RK73HB1J153J MG RESISTOR 15kΩ 1/16W JR427 RK73HB1J333J MG RESISTOR 33kΩ 1/16W JR428 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR429 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR431 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR432 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR433 RK73JB1H472J MG RESISTOR 4.7kΩ 1/20W JR434 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR435 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR436 RK73JB1H105J MG RESISTOR 1MΩ 1/20W JR437 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR438 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR439 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR440 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR441 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR442 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR443 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR444 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR445 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR446 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR447 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR448 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR449 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR450 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR451 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR452 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR453 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR454 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR455 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR456 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR457 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR458 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR459 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR460 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR461 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR462 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR463 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR464 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR465 RK73JB1H220J MG RESISTOR 22Ω 1/20W J
Symbol No. Part No. Part Name Description Local
3-8(No.RA054<Rev.001>)
R466 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR467 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR468 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR469 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR470 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR471 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR472 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR473 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR474 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR475 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR476 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR477 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR478 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR479 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR480 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR481 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR482 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR483 RK73GH2A49R9D MG RESISTOR 49.9Ω 1/10W DR484 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR485 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR486 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR487 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR488 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR489 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR490 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR491 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR492 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR493 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR494 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR495 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR496 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR497 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR498 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR499 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR500 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR501 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR502 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR503 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR504 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR505 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR506 RK73HH1J104D MG RESISTOR 100kΩ 1/16W DR507 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR508 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR509 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR511 RK73HB1J333J MG RESISTOR 33kΩ 1/16W JR512 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR513 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR514 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR516 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR517 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR518 RK73HB1J393J MG RESISTOR 39kΩ 1/16W JR519 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR520 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR522 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR523 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR524 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR525 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR526 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR527 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR528 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR529 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR530 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR531 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR532 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR533 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR534 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR535 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR536 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR537 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR538 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR539 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR613 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR614 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR615 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR616 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR617 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR618 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR619 RK73HB1J103J MG RESISTOR 10kΩ 1/16W J
Symbol No. Part No. Part Name Description Local
R620 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR621 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR622 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR623 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR624 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR625 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR626 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR627 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR628 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR629 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR630 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR631 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR632 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR633 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR634 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR635 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR636 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR637 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR638 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR639 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR640 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR641 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR642 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR643 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR644 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR645 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR646 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR647 RK73HB1J682J MG RESISTOR 6.8kΩ 1/16W JR648 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR649 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR650 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR651 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR652 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR653 RK73HB1J682J MG RESISTOR 6.8kΩ 1/16W JR654 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR655 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR656 RK73FB2B102J MG RESISTOR 1kΩ 1/8W JR657 RK73FB2B102J MG RESISTOR 1kΩ 1/8W JR658 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR659 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR660 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR661 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR662 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR663 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR664 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR665 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR666 RK73HB1J683J MG RESISTOR 68kΩ 1/16W JR667 RK73HB1J123J MG RESISTOR 12kΩ 1/16W JR668 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR669 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR670 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR671 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR672 RK73HH1J273D MG RESISTOR 27kΩ 1/16W DR673 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR674 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR675 RK73HB1J682J MG RESISTOR 6.8kΩ 1/16W JR676 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR677 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR678 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR679 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR680 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR681 RK73HH1J152D MG RESISTOR 1.5kΩ 1/16W D
L1 L34-4902-05 AIR CORE COILL2 L34-4903-05 AIR CORE COILL3 L34-4903-05 AIR CORE COILL4 L34-4903-05 AIR CORE COILL5 L3E-0018-00 AIR CORE COILL6 L34-4848-05 AIR CORE COILL7 L34-4610-15 AIR CORE COILL11 LB73G0AK-001 CHIP FERRITEL12 LR79Z0FQ100M CHIP INDUCTORL13 LB73G0AM-004 CHIP FERRITEL14 LR79Z0AA150M CHIP INDUCTORL15 LB73G0AM-004 CHIP FERRITEL16 LB73G0AK-001 CHIP FERRITEL17 LB73H0AV-002 CHIP FERRITEL18 LB73H0AV-002 CHIP FERRITE
Symbol No. Part No. Part Name Description Local
(No.RA054<Rev.001>)3-9
TX-RX UNITXC1-183K-01 (NX-3820E,NX-3820GE,NX-3820HGK2,NX-3820HK2)XC1-183K-00 (NX-3820HGK,NX-3820HK)*Note : This part cannot be replaced.Therefore, this part is not supplied as a service part.
Block No. [0][2]
L19 LB73G0AK-001 CHIP FERRITEL107 LB73H0AV-003 CHIP FERRITEL108 L41-2785-53 CHIP INDUCTORL109 LB73H0AV-003 CHIP FERRITEL110 L41-2785-53 CHIP INDUCTORL111 L41-2785-53 CHIP INDUCTORL112 L41-2785-53 CHIP INDUCTORL113 L41-2785-53 CHIP INDUCTORL115 L41-2785-53 CHIP INDUCTORL116 L41-2785-53 CHIP INDUCTORL117 LB73H0AY-004 CHIP FERRITEL118 LK73H0AM47NJ M.CHIP INDUCTOR 47nHL119 LB73H0AY-004 CHIP FERRITEL121 LK73H0AM27NJ M.CHIP INDUCTOR 27nHL123 LK73H0AM27NJ M.CHIP INDUCTOR 27nHL124 LK73H0AM56NJ M.CHIP INDUCTOR 56nHL207 LB73H0AY-004 CHIP FERRITEL208 LB73H0AY-004 CHIP FERRITEL209 LK73H0AM56NJ M.CHIP INDUCTOR 56nHL210 L41-2785-53 CHIP INDUCTORL211 LK73H0AM56NJ M.CHIP INDUCTOR 56nHL212 LK73H0AM56NJ M.CHIP INDUCTOR 56nHL213 LK73H0AM47NJ M.CHIP INDUCTOR 47nHL214 L41-8275-53 CHIP INDUCTORL215 LB73F0AW-002 CHIP FERRITEL217 LB73H0AV-003 CHIP FERRITEL218 LB73G0BA-004 CHIP FERRITEL219 LB73Z0DF-001 CHIP FERRITEL220 LB73Z0DF-001 CHIP FERRITEL221 LB73Z0DF-001 CHIP FERRITEL222 L41-2775-53 CHIP INDUCTORL223 LR77Z0AAR27J CHIP INDUCTOR 0.27uHL224 LR79Z0GJR56G CHIP INDUCTORL225 LB73H0AY-004 CHIP FERRITEL226 LB73H0AV-003 CHIP FERRITEL302 LK73H0AMR10J M.CHIP INDUCTOR 0.1uHL303 LR79G0CQ56NG CHIP INDUCTORL304 LR79G0CQ47NG CHIP INDUCTORL305 LR79G0CQ82NG CHIP INDUCTORL306 LR79G0CQ8N2C CHIP INDUCTORL307 LR79G0CQR22G CHIP INDUCTORL308 LR79G0CQR12G CHIP INDUCTORL309 LR79G0CQ68NG CHIP INDUCTOR 68nHL310 LR79G0CQ82NG CHIP INDUCTORL311 LR79G0CQR33G CHIP INDUCTORL312 LK73H0AMR10J M.CHIP INDUCTOR 0.1uHL313 LR79G0CQ56NG CHIP INDUCTORL314 LK73H0AMR27J M.CHIP INDUCTORL315 LR79G0CQR10G CHIP INDUCTORL317 LK73H0AM33NJ M.CHIP INDUCTOR 33nHL401 LB73G0AK-001 CHIP FERRITEL402 LB73H0AV-003 CHIP FERRITEL403 LB73G0AK-001 CHIP FERRITEL404 LR77Z0AE4R7J CHIP INDUCTOR 4.7uHL405 LB73G0AM-004 CHIP FERRITEL406 L92-1101-05 CHIP FERRITEL407 L92-1101-05 CHIP FERRITEL408 L92-1101-05 CHIP FERRITEL409 L92-1101-05 CHIP FERRITEL410 LB73G0AK-001 CHIP FERRITEL411 LB73G0AK-001 CHIP FERRITEL412 LB73G0AK-001 CHIP FERRITEL413 LB73G0AK-001 CHIP FERRITEL414 LB73H0AV-002 CHIP FERRITEL415 L79-1984-05 FILTERL416 L79-1984-05 FILTERL417 LB73H0AY-002 CHIP FERRITEL418 LB73H0AY-002 CHIP FERRITEL419 L79-1984-05 FILTERL420 L92-1101-05 CHIP FERRITEL601 LB73H0AV-003 CHIP FERRITEL602 LB73H0AV-003 CHIP FERRITEL603 LB73H0AV-003 CHIP FERRITE
CN1 EC720AA-0560A FFC FPC CONNECN2 E40-6862-05 F.C.CONNECTORCN3 J19-5386-05 HOLDERCP301 RK74HB1J100J NET RESISTOR 10Ω 1/16W J
Symbol No. Part No. Part Name Description Local
CP302 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP303 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP401 RK74HB1J103J NET RESISTOR 10kΩ 1/16W JCP402 RK74HB1J222J NET RESISTOR 2.2kΩ 1/16W JCP403 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP404 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP405 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP406 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP407 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP408 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP409 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP410 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP411 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP412 RK74HB1J470J NET RESISTOR 47Ω 1/16W JCP413 RK74HB1J470J NET RESISTOR 47Ω 1/16W JCP414 RK74HB1J470J NET RESISTOR 47Ω 1/16W JCP601 RK74HB1J472J NET RESISTOR 4.7kΩ 1/16W JCP602 RK74HB1J472J NET RESISTOR 4.7kΩ 1/16W JCP604 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP605 RK74HB1J101J NET RESISTOR 100Ω 1/16W JE11 F1B-0085-00 SHIELDING CASEE101 F1B-0085-00 SHIELDING CASEF1 F53-0286-05 FUSEF2 F53-0286-05 FUSEF3 F53-0286-05 FUSEF4 FZA10BS-5R0 FUSE (CC)F5 FZA10BS-5R0 FUSE (CC)F6 F53-0286-05 FUSEIC201 RA60H1317A501 MOS ICIC601 LA4631VC-XE ANALOG ICJ1 E58-0567-05 SUB SOCKET DJ2 E1B-0001-00 3.5D PHONE JACKTH201 NCU15WF104F6S N THERMISTORTH202 NCU15WF104F6S N THERMISTORTH203 NCU15WF104F6S N THERMISTORTH401 NCU15WF104F6S N THERMISTORX401 L7H-0076-00 TCXOX402 L77-1802-05 QUARTZ CRYSTAL
Symbol No. Part No. Part Name Description Local
IC1 BA00DD0WHFP ICIC12 LXDC2HN18F163 ICIC13 BU31TD2WNVX ICIC14 TPS61041DRVR ICIC15 XC6215B122N-G ICIC16 XC6209B502P-G ICIC17 NJM2878F4-32 ICIC18 XC61CN5002N-G ICIC19 XC6223D321G-G ICIC20 XC6223D321P-G ICIC21 XC8102AA07-G ICIC22 MSP430G2533P0 ICIC23 XC6221D501G-G ICIC24 LXDC2XQ12A-252 ICIC25 MP2560DQ-LF-Z ICIC26 XC6221D501G-G ICIC101 NJM2904CRB1 ICIC202 BGU6104 ICIC203 BA3472FVM ICIC205 AD8315ARM ICIC301 NJG1608KB2 ICIC302 AK2401 IC
Symbol No. Part No. Part Name Description Local
3-10(No.RA054<Rev.001>)
IC401 ------------ IC *NoteIC402 ------------ IC *NoteIC403 TC7SZ08FE ICIC404 ------------ IC *NoteIC405 BD11600NUX ICIC406 BD11600NUX ICIC407 TC7SET125FUF ICIC408 TC7SZ08FE ICIC409 TCA9555RTWR ICIC410 ADS7961SRHB ICIC411 DAC124S085CIS ICIC412 R2A20178NP ICIC413 XC61CN5002N-G ICIC414 BU7462NUX ICIC602 TC7WT126FU-F ICIC603 TC7WH126FK ICIC604 TCA9555RTWR ICIC605 ADM3202ARUZ ICIC606 TC7SET125FUF ICIC607 TLV32AIC3104I ICIC608 BU7462NUX ICIC609 XC6221D501G-G IC
Q11 LTC014EEBFS8 DIGI TRANSISTORQ12 TPCP8107-F FETQ13 LTC014EEBFS8 DIGI TRANSISTORQ14 LTC014TEBFS8 DIGI TRANSISTORQ15 LSCR523EBFS8 TRANSISTORQ16 LSAR523UBFS8 TRANSISTORQ17 TPCP8107-F FETQ18 LTC014EEBFS8 DIGI TRANSISTORQ19 VT6M1 FETQ20 SSM3J334R FETQ21 LTC014EEBFS8 DIGI TRANSISTORQ22 SSM3J334R FETQ23 LTC014EEBFS8 DIGI TRANSISTORQ25 EMD9 DIGI TRANSISTORQ101 2SC5108FT/Y/ TRANSISTORQ102 2SC5108FT/Y/ TRANSISTORQ103 EM6M2 FETQ104 2SD2654/W/ TRANSISTORQ105 MCH3914-H/8/ FETQ106 2SC5108FT/Y/ TRANSISTORQ201 RFM01U7PF FETQ202 LSCR523EBFS8 TRANSISTORQ204 LSCR523EBFS8 TRANSISTORQ205 EMD9 DIGI TRANSISTORQ206 VT6M1 FETQ301 SSM3K15AMFV FETQ401 2SC4617/S/ TRANSISTORQ402 SSM3K15AMFV FETQ403 SSM3K15AMFV FETQ404 LTC014TEBFS8 DIGI TRANSISTORQ601 SSM6N15AFEM DUAL FETQ602 LTC014TEBFS8 DIGI TRANSISTORQ603 TPCP8107-F FETQ604 LTC014TEBFS8 DIGI TRANSISTORQ605 SSM6N15AFEM DUAL FETQ606 SSM3J334R FET
D1 ST70-27F-572 ZENER DIODED13 EDZV5.6B ZENER DIODED14 RB521CM-30 DIODED15 1SS400SM DIODED16 RB060M-40 DIODED17 RB561VM-40 SCHOTTKY DIODED18 RB521CM-30 DIODED19 RB521CM-30 DIODED20 EDZV18B ZENER DIODED21 RB520SM-30 DIODED22 EDZV8.2B ZENER DIODED24 RB520SM-30 DIODED26 RB521CM-30 DIODED27 RB521CM-30 DIODED101 EDZV8.2B ZENER DIODED102 SMV1270-079LF VARI CAP DIODED103 1SV282-F VARI CAP DIODED104 1SV282-F VARI CAP DIODE
Symbol No. Part No. Part Name Description Local
D105 1SV282-F VARI CAP DIODED106 1SV282-F VARI CAP DIODED107 1SS400SM DIODED108 SMV1130-079LF VARI CAP DIODED201 EDZV5.6B ZENER DIODED202 RN142S DIODED204 RB706F-40 DIODED205 L8104 DIODED206 L8104 DIODED207 L8104 DIODED208 RN142S DIODED209 RN142S DIODED301 1SS390 DIODED302 1SS390 DIODED303 1SS400SM DIODED304 1SS400SM DIODED401 RB521CM-30 DIODED402 SPC10501A01 VARISTORD403 SPC10501A01 VARISTORD404 SPC10501A01 VARISTORD405 SPC10501A01 VARISTORD406 SPC10501A01 VARISTORD407 EDZV8.2B ZENER DIODED408 RB521CM-30 DIODED409 RB521CM-30 DIODED410 RB521CM-30 DIODED601 EDZV5.6B ZENER DIODED602 RB521CM-30 DIODED603 EDZV6.8B ZENER DIODED604 EDZV6.8B ZENER DIODED605 EDZV6.8B ZENER DIODED606 EDZV6.8B ZENER DIODED607 EDZV6.8B ZENER DIODED608 EDZV6.8B ZENER DIODED609 RB521CM-30 DIODED610 RB521CM-30 DIODED611 EDZV6.8B ZENER DIODED612 DA204U MULTIPLE DIODED613 DA204U MULTIPLE DIODED614 RB521CM-30 DIODED615 RB521CM-30 DIODED616 AVRM10270K101 VARISTORD617 AVRM10270K101 VARISTORD618 RB520SM-30 DIODED619 RB521CM-30 DIODE
C1 CE32EJ1E102M E CAPACITOR 1000uF 25V MC2 C92-0906-05 E CAPACITOR 330uF 10VC3 C92-0906-05 E CAPACITOR 330uF 10VC4 CE32BY1E470M E CAPACITOR 47uF 25V MC5 C92-0968-05 E CAPACITOR 470uF 25VC11 CK73HB1E104K C CAPACITOR 0.10uF 25V KC12 CK73HBB1H102K C CAPACITOR 1000pF 50V KC14 CK73FB1C106K C CAPACITOR 10uF 16V KC15 CK73HB1E104K C CAPACITOR 0.10uF 25V KC16 C93-1959-05 C CAPACITOR 0.1uF 16VC17 CK73HB1A474K C CAPACITOR 0.47uF 10V KC18 CK73HB1C105K C CAPACITOR 1.0uF 16V KC19 CK73HB1H103K C CAPACITOR 10000pF 50V KC20 CK73HBB1H471K C CAPACITOR 470pF 50V KC21 CK73HBB1H471K C CAPACITOR 470pF 50V KC22 CK73HBB1H471K C CAPACITOR 470pF 50V KC24 CK73HB1C105K C CAPACITOR 1.0uF 16V KC25 CK73HBB1H102K C CAPACITOR 1000pF 50V KC26 CC73HCH1H101J C CAPACITOR 100pF 50V JC27 CK73HBB1H102K C CAPACITOR 1000pF 50V KC28 CK73GB1H105K C CAPACITOR 1uF 50V KC29 CK73HBB1H222K C CAPACITOR 2200pF 50V KC30 CK73EB1H475KM C CAPACITOR 4.7uF 50V MC31 CK73HB1C105K C CAPACITOR 1.0uF 16V KC32 CK73EB1H475KM C CAPACITOR 4.7uF 50V MC33 CK73GB1H105K C CAPACITOR 1uF 50V KC34 CK73EB1H475KM C CAPACITOR 4.7uF 50V MC35 CK73HB1E104K C CAPACITOR 0.10uF 25V KC36 CK73HBB1H471K C CAPACITOR 470pF 50V KC37 CK73GB1H105K C CAPACITOR 1uF 50V KC38 CK73FB1C106K C CAPACITOR 10uF 16V KC39 CK73HBB1H471K C CAPACITOR 470pF 50V K
Symbol No. Part No. Part Name Description Local
(No.RA054<Rev.001>)3-11
C40 CK73GB0J106K C CAPACITOR 10uF 6.3V KC41 CK73GB1H105K C CAPACITOR 1uF 50V KC42 CK73HBB1H471K C CAPACITOR 470pF 50V KC43 CK73HB1C105K C CAPACITOR 1.0uF 16V KC44 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC45 CK73HB1E104K C CAPACITOR 0.10uF 25V KC46 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC47 CK73HBB1H102K C CAPACITOR 1000pF 50V KC48 CC73HCH1H101J C CAPACITOR 100pF 50V JC49 CK73HB1E104K C CAPACITOR 0.10uF 25V KC50 CK73GB1H105K C CAPACITOR 1uF 50V KC51 CK73HBB1H471K C CAPACITOR 470pF 50V KC52 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC53 CK73FB1C106K C CAPACITOR 10uF 16V KC54 CK73FB1C106K C CAPACITOR 10uF 16V KC55 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC56 CK73HBB1H102K C CAPACITOR 1000pF 50V KC57 CK73GB0J106K C CAPACITOR 10uF 6.3V KC58 CK73FB1C106K C CAPACITOR 10uF 16V KC59 CK73FB1C106K C CAPACITOR 10uF 16V KC60 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC61 CK73HB1H391K C CAPACITOR 390pF 50V KC62 CK73HB1H391K C CAPACITOR 390pF 50V KC63 CK730FA1H475K C CAPACITOR 4.7uF 50V KC64 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC65 CK730DT1C476K C CAPACITOR 47uF 16V KC66 CK73HB1E104K C CAPACITOR 0.10uF 25V KC67 CC73HCH1H470G C CAPACITOR 47pF 50V GC68 CK73HB1C105K C CAPACITOR 1.0uF 16V KC69 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC72 CK73HB1C105K C CAPACITOR 1.0uF 16V KC73 CK73HB1C105K C CAPACITOR 1.0uF 16V KC74 CK73HB1E104K C CAPACITOR 0.10uF 25V KC75 CK73HB1E473K C CAPACITOR 0.047uF 25V KC76 CK73HB1C105K C CAPACITOR 1.0uF 16V KC101 CC73HCH1H040B C CAPACITOR 4pF 50V B
C102 CC73HCH1H3R5B C CAPACITOR 3.5pF 50V B3820E,3820GE,3820HGK2,3820HK2
C103 CC73HCH1H100B C CAPACITOR 10pF 50V B3820E,3820GE,3820HGK2,3820HK2
C103 CC73HCH1H101J C CAPACITOR 100pF 50V J 3820HGK,3820HK
C104 CC73HCH1H070B C CAPACITOR 7pF 50V B3820E,3820GE,3820HGK2,3820HK2
C105 CC73HCH1H470G C CAPACITOR 47pF 50V GC108 CK73HB1H103K C CAPACITOR 10000pF 50V KC109 CC73HCH1H330G C CAPACITOR 33pF 50V GC110 CC73HCH1H101J C CAPACITOR 100pF 50V JC111 CK73GB1H105K C CAPACITOR 1uF 50V KC112 CC73HCH1H101J C CAPACITOR 100pF 50V JC113 CK73FBB1H154K C CAPACITOR 0.15uF 50V KC114 CS77ABE1D100M TA E CAPACITOR 10uF 20V MC115 CK73FB1H473K C CAPACITOR 0.047uF 50V KC116 CC730AD1H104J C CAPACITOR 0.1uF 50V JC117 CC73HCH1H101J C CAPACITOR 100pF 50V JC119 CC73HCH1H470G C CAPACITOR 47pF 50V GC120 CC73HCH1H101J C CAPACITOR 100pF 50V J
C121 CC73HCH1H3R5B C CAPACITOR 3.5pF 50V B3820E,3820GE,3820HGK2,3820HK2
C122 CC73HCH1H1R5B C CAPACITOR 1.5pF 50V B3820E,3820GE,3820HGK2,3820HK2
C122 CC73HCH1H020B C CAPACITOR 2pF 50V B 3820HGK,3820HKC123 CC73HCH1H221J C CAPACITOR 220pF 50V JC124 CK73HBB1H471K C CAPACITOR 470pF 50V KC125 CC73HCH1H101J C CAPACITOR 100pF 50V J
C126 CC73HCH1H010B C CAPACITOR 1pF 50V B3820E,3820GE,3820HGK2,3820HK2
C126 CC73HCH1H020B C CAPACITOR 2pF 50V B 3820HGK,3820HKC127 CC73HCH1H221J C CAPACITOR 220pF 50V JC128 CC73HCH1H020B C CAPACITOR 2pF 50V BC129 CC73HCH1H0R5B C CAPACITOR 0.5pF 50V BC130 CK73FB1C106K C CAPACITOR 10uF 16V KC131 CC73HCH1H090B C CAPACITOR 9pF 50V BC132 CC73HCH1H090B C CAPACITOR 9pF 50V BC133 CC73HCH1H070B C CAPACITOR 7pF 50V BC134 CK73HBB1H471K C CAPACITOR 470pF 50V KC135 CC73HCH1H0R5B C CAPACITOR 0.5pF 50V BC136 CC73HCH1H101J C CAPACITOR 100pF 50V J
Symbol No. Part No. Part Name Description Local
C137 CC73HCH1H1R5B C CAPACITOR 1.5pF 50V B3820E,3820GE,3820HGK2,3820HK2
C137 CC73HCH1H020B C CAPACITOR 2pF 50V B 3820HGK,3820HKC138 CC73HCH1H470G C CAPACITOR 47pF 50V GC139 CC73HCH1H090B C CAPACITOR 9pF 50V BC140 CC73HCH1H0R5B C CAPACITOR 0.5pF 50V B
C141 CC73HCH1H120G C CAPACITOR 12pF 50V G3820E,3820GE,3820HGK2,3820HK2
C141 CC73HCH1H100B C CAPACITOR 10pF 50V B 3820HGK,3820HKC142 CC73HCH1H0R5B C CAPACITOR 0.5pF 50V BC143 CC73HCH1H090B C CAPACITOR 9pF 50V B
C144 CC73HCH1H040B C CAPACITOR 4pF 50V B3820E,3820GE,3820HGK2,3820HK2
C145 CK73HBB1H102K C CAPACITOR 1000pF 50V K
C146 CC73HCH1H040B C CAPACITOR 4pF 50V B3820E,3820GE,3820HGK2,3820HK2
C147 CC73HCH1H030B C CAPACITOR 3pF 50V B3820E,3820GE,3820HGK2,3820HK2
C148 CC73HCH1H030B C CAPACITOR 3pF 50V B3820E,3820GE,3820HGK2,3820HK2
C201 CC73HCH1H020B C CAPACITOR 2pF 50V B
C207 C93-1838-05 C CAPACITOR 2pF 250V3820E,3820GE,3820HGK2,3820HK2
C211 CK73HB1C105K C CAPACITOR 1.0uF 16V KC212 CK73HBB1H471K C CAPACITOR 470pF 50V KC213 CC73HCH1H121J C CAPACITOR 120pF 50V JC214 CK73HB1H103K C CAPACITOR 10000pF 50V KC216 CC73HCH1H150G C CAPACITOR 15pF 50V GC217 CC73HCH1H050B C CAPACITOR 5pF 50V BC218 CC73HCH1H150G C CAPACITOR 15pF 50V GC219 CC73HCH1H050B C CAPACITOR 5pF 50V BC220 CK73HBB1H471K C CAPACITOR 470pF 50V KC221 CK73HB1E473K C CAPACITOR 0.047uF 25V KC222 CK73HBB1H472K C CAPACITOR 4700pF 50V KC223 CC73HCH1H101J C CAPACITOR 100pF 50V JC224 CK73HBB1H471K C CAPACITOR 470pF 50V KC225 CK73HBB1H471K C CAPACITOR 470pF 50V KC226 CC73HCH1H050B C CAPACITOR 5pF 50V BC227 CC73HCH1H100B C CAPACITOR 10pF 50V BC228 CC73HCH1H050B C CAPACITOR 5pF 50V BC229 CC73HCH1H220G C CAPACITOR 22pF 50V GC230 CC73HCH1H080B C CAPACITOR 8pF 50V BC231 CC73HCH1H101J C CAPACITOR 100pF 50V JC232 CK73HBB1H471K C CAPACITOR 470pF 50V KC233 CK73HBB1H471K C CAPACITOR 470pF 50V KC234 CC73GCH1H040B C CAPACITOR 4pF 50V BC235 CK73HB1H103K C CAPACITOR 10000pF 50V KC236 CC73HCH1H470G C CAPACITOR 47pF 50V GC237 CC73HCH1H470G C CAPACITOR 47pF 50V GC238 CK73GB1H471K C CAPACITOR 470pF 50V KC239 CK73HBB1H472K C CAPACITOR 4700pF 50V KC241 CK73GB1H471K C CAPACITOR 470pF 50V KC242 CC73HCH1H220G C CAPACITOR 22pF 50V GC243 CC73HCH1H470G C CAPACITOR 47pF 50V GC244 CC73HCH1H101J C CAPACITOR 100pF 50V JC245 CK73HBB1H471K C CAPACITOR 470pF 50V KC247 CC73HCH1H101J C CAPACITOR 100pF 50V JC249 CC73HCH1H101J C CAPACITOR 100pF 50V JC250 C93-1866-05 C CAPACITOR 27pF 250VC251 CK73HBB1H471K C CAPACITOR 470pF 50V KC252 CK73HB1E104K C CAPACITOR 0.10uF 25V K
C253 CC73GCH1H1R5B C CAPACITOR 1.5pF 50V B3820E,3820GE,3820HGK2,3820HK2
C253 CC73GCH1H020B C CAPACITOR 2pF 50V B 3820HGK,3820HKC254 CK73GB1H471K C CAPACITOR 470pF 50V KC255 CK73GB1H471K C CAPACITOR 470pF 50V KC256 C93-1866-05 C CAPACITOR 27pF 250VC257 CK73GB1H471K C CAPACITOR 470pF 50V KC258 CK73GB1H471K C CAPACITOR 470pF 50V K
C259 C93-1846-05 C CAPACITOR 4pF 250V3820E,3820GE,3820HGK2,3820HK2
C259 C93-1852-05 C CAPACITOR 6pF 250V 3820HGK,3820HKC260 CK73HB1E104K C CAPACITOR 0.10uF 25V KC261 CC73GCH1H040B C CAPACITOR 4pF 50V BC262 C93-1932-05 C CAPACITOR 100pF 250VC263 CK73HBB1H472K C CAPACITOR 4700pF 50V K
C264 CC730DF2H130G C CAPACITOR 13pF 500V G3820E,3820GE,3820HGK2,3820HK2
Symbol No. Part No. Part Name Description Local
3-12(No.RA054<Rev.001>)
C264 C93-2035-05 C CAPACITOR 9pF 500V 3820HGK,3820HK
C265 C93-1846-05 C CAPACITOR 4pF 250V3820E,3820GE,3820HGK2,3820HK2
C266 CC73HCH1H470G C CAPACITOR 47pF 50V G
C267 CC730DF2H130G C CAPACITOR 13pF 500V G3820E,3820GE,3820HGK2,3820HK2
C267 C93-2039-05 C CAPACITOR 10pF 500V 3820HGK,3820HKC268 C93-1852-05 C CAPACITOR 6pF 250VC270 CK73HBB1H471K C CAPACITOR 470pF 50V KC271 CK73HBB1H471K C CAPACITOR 470pF 50V KC272 CK73HBB1H471K C CAPACITOR 470pF 50V KC274 CC73GCH1H020B C CAPACITOR 2pF 50V BC304 CC73JCH1H101J C CAPACITOR 100pF 50V JC305 CC73JCH1H101J C CAPACITOR 100pF 50V JC306 CK73HBB1H471K C CAPACITOR 470pF 50V KC307 CC73HCH1H020B C CAPACITOR 2pF 50V BC308 CC73HCH1H080B C CAPACITOR 8pF 50V BC309 CC73HCH1H040B C CAPACITOR 4pF 50V BC310 CC73HCH1H070B C CAPACITOR 7pF 50V BC311 CC73HCH1H050B C CAPACITOR 5pF 50V BC312 CC73HCH1H040B C CAPACITOR 4pF 50V BC313 CK73HBB1H471K C CAPACITOR 470pF 50V KC314 CK73HB1H103K C CAPACITOR 10000pF 50V KC315 CK73HB1C105K C CAPACITOR 1.0uF 16V KC316 CK73HB1C105K C CAPACITOR 1.0uF 16V KC317 CC73HCH1H1R5B C CAPACITOR 1.5pF 50V BC319 CC73HCH1H060B C CAPACITOR 6pF 50V BC320 CC73HCH1H150G C CAPACITOR 15pF 50V GC321 CK730BS0J106M C CAPACITOR 10uF 6.3V MC322 CC73HCH1H101J C CAPACITOR 100pF 50V JC323 CC73HCH1H101J C CAPACITOR 100pF 50V JC324 CK73HB1H103K C CAPACITOR 10000pF 50V KC325 CC73HCH1H101J C CAPACITOR 100pF 50V JC326 CC73HCH1H101J C CAPACITOR 100pF 50V JC327 CK73HB1C105K C CAPACITOR 1.0uF 16V KC328 CK73HB1E104K C CAPACITOR 0.10uF 25V KC329 CC73HCH1H101J C CAPACITOR 100pF 50V JC330 CK73HB1E104K C CAPACITOR 0.10uF 25V KC331 CK73HBB1H102K C CAPACITOR 1000pF 50V KC332 CC73HCH1H101J C CAPACITOR 100pF 50V JC333 CC73HCH1H150G C CAPACITOR 15pF 50V GC334 CC73HCH1H030B C CAPACITOR 3pF 50V BC335 CC73HCH1H101J C CAPACITOR 100pF 50V JC336 CK73HB1E104K C CAPACITOR 0.10uF 25V K
C337 CK73HBB1H471K C CAPACITOR 470pF 50V K3820E,3820GE,3820HGK2,3820HK2
C337 CC73HCH1H470G C CAPACITOR 47pF 50V G 3820HGK,3820HKC338 CK73HBB1H471K C CAPACITOR 470pF 50V KC339 CC73HCH1H040B C CAPACITOR 4pF 50V BC340 CK73HB1E104K C CAPACITOR 0.10uF 25V KC341 CK73HBB1H471K C CAPACITOR 470pF 50V KC342 CK73HB0J225K C CAPACITOR 2.2uF 6.3V KC343 CC73HCH1H101J C CAPACITOR 100pF 50V JC344 CK730BS0J106M C CAPACITOR 10uF 6.3V MC345 CK73HB1A474K C CAPACITOR 0.47uF 10V KC346 CK730BS0J106M C CAPACITOR 10uF 6.3V MC347 CK73HB1E104K C CAPACITOR 0.10uF 25V KC405 CK73HBB1H472K C CAPACITOR 4700pF 50V KC410 CK73HBB1H102K C CAPACITOR 1000pF 50V KC411 CK73HBB1H102K C CAPACITOR 1000pF 50V KC412 CK73HB1H103K C CAPACITOR 10000pF 50V KC414 CK73HB1C105K C CAPACITOR 1.0uF 16V KC415 C93-1959-05 C CAPACITOR 0.1uF 16VC416 C93-1959-05 C CAPACITOR 0.1uF 16VC417 CK73FXR0J226M C CAPACITOR 22uF 6.3V MC418 CK73HB1H103K C CAPACITOR 10000pF 50V KC419 C93-1959-05 C CAPACITOR 0.1uF 16VC420 C93-1959-05 C CAPACITOR 0.1uF 16VC421 CK73FXR0J226M C CAPACITOR 22uF 6.3V MC422 CK73GB0J106K C CAPACITOR 10uF 6.3V KC423 C93-1959-05 C CAPACITOR 0.1uF 16VC424 C93-1959-05 C CAPACITOR 0.1uF 16VC425 C93-1959-05 C CAPACITOR 0.1uF 16VC426 C93-1959-05 C CAPACITOR 0.1uF 16VC427 C93-1959-05 C CAPACITOR 0.1uF 16VC428 C93-1959-05 C CAPACITOR 0.1uF 16VC429 C93-1959-05 C CAPACITOR 0.1uF 16VC430 C93-1959-05 C CAPACITOR 0.1uF 16V
Symbol No. Part No. Part Name Description Local
C431 C93-1959-05 C CAPACITOR 0.1uF 16VC432 C93-1959-05 C CAPACITOR 0.1uF 16VC433 CC73JCH1H101J C CAPACITOR 100pF 50V JC434 C93-1959-05 C CAPACITOR 0.1uF 16VC435 C93-1959-05 C CAPACITOR 0.1uF 16VC436 CK73HB1H103K C CAPACITOR 10000pF 50V KC437 CK73GB0J106K C CAPACITOR 10uF 6.3V KC438 CK73HB1H103K C CAPACITOR 10000pF 50V KC439 CK73GB0J106K C CAPACITOR 10uF 6.3V KC440 C93-1959-05 C CAPACITOR 0.1uF 16VC441 C93-1959-05 C CAPACITOR 0.1uF 16VC442 C93-1959-05 C CAPACITOR 0.1uF 16VC443 C93-1959-05 C CAPACITOR 0.1uF 16VC444 C93-1959-05 C CAPACITOR 0.1uF 16VC445 CC73JCH1H101J C CAPACITOR 100pF 50V JC446 CK73GB0J106K C CAPACITOR 10uF 6.3V KC447 CK73HB1H103K C CAPACITOR 10000pF 50V KC448 C93-1959-05 C CAPACITOR 0.1uF 16VC449 CK73GB0J106K C CAPACITOR 10uF 6.3V KC450 CK73HB1H103K C CAPACITOR 10000pF 50V KC451 C93-1959-05 C CAPACITOR 0.1uF 16VC452 CK73GB0J106K C CAPACITOR 10uF 6.3V KC453 CK73GB0J106K C CAPACITOR 10uF 6.3V KC454 CC73HCH1H050B C CAPACITOR 5pF 50V BC455 C93-1959-05 C CAPACITOR 0.1uF 16VC456 CK73GB0J106K C CAPACITOR 10uF 6.3V KC457 C93-1959-05 C CAPACITOR 0.1uF 16VC458 C93-1959-05 C CAPACITOR 0.1uF 16VC459 C93-1959-05 C CAPACITOR 0.1uF 16VC460 C93-1959-05 C CAPACITOR 0.1uF 16VC461 C93-1959-05 C CAPACITOR 0.1uF 16VC462 CK73HB1C105K C CAPACITOR 1.0uF 16V KC463 C93-1959-05 C CAPACITOR 0.1uF 16VC464 C93-1959-05 C CAPACITOR 0.1uF 16VC465 C93-1959-05 C CAPACITOR 0.1uF 16VC466 C93-1959-05 C CAPACITOR 0.1uF 16VC467 C93-1959-05 C CAPACITOR 0.1uF 16VC468 C93-1959-05 C CAPACITOR 0.1uF 16VC469 C93-1959-05 C CAPACITOR 0.1uF 16VC470 C93-1959-05 C CAPACITOR 0.1uF 16VC471 C93-1959-05 C CAPACITOR 0.1uF 16VC472 C93-1959-05 C CAPACITOR 0.1uF 16VC473 C93-1959-05 C CAPACITOR 0.1uF 16VC474 C93-1959-05 C CAPACITOR 0.1uF 16VC475 C93-1959-05 C CAPACITOR 0.1uF 16VC476 C93-1959-05 C CAPACITOR 0.1uF 16VC477 C93-1959-05 C CAPACITOR 0.1uF 16VC478 CK73HB1C105K C CAPACITOR 1.0uF 16V KC479 C93-1959-05 C CAPACITOR 0.1uF 16VC480 CC73HCH1H180G C CAPACITOR 18pF 50V GC481 CC73HCH1H150G C CAPACITOR 15pF 50V GC482 CK73HB1E104K C CAPACITOR 0.10uF 25V KC483 CK73HB1A224K C CAPACITOR 0.22uF 10V KC484 CK73HBB1H102K C CAPACITOR 1000pF 50V KC485 C93-1959-05 C CAPACITOR 0.1uF 16VC486 C93-1959-05 C CAPACITOR 0.1uF 16VC487 CK73HB1H103K C CAPACITOR 10000pF 50V KC488 CK73HB1H103K C CAPACITOR 10000pF 50V KC489 CK73GB1H105K C CAPACITOR 1uF 50V KC490 CK73HB1E104K C CAPACITOR 0.10uF 25V KC491 CK73HB1H103K C CAPACITOR 10000pF 50V KC492 CC73JCH1H101J C CAPACITOR 100pF 50V JC493 CK73HB1C105K C CAPACITOR 1.0uF 16V KC494 C93-1959-05 C CAPACITOR 0.1uF 16VC495 C93-1959-05 C CAPACITOR 0.1uF 16VC497 C93-1959-05 C CAPACITOR 0.1uF 16VC498 CK73HB1H103K C CAPACITOR 10000pF 50V KC501 CC73JCH1H101J C CAPACITOR 100pF 50V JC502 C93-1959-05 C CAPACITOR 0.1uF 16VC503 CC73JCH1H101J C CAPACITOR 100pF 50V JC504 CC73HCH1H101J C CAPACITOR 100pF 50V JC505 CC73JCH1H101J C CAPACITOR 100pF 50V JC506 CC73JCH1H101J C CAPACITOR 100pF 50V JC507 CC73JCH1H101J C CAPACITOR 100pF 50V JC509 CC73JCH1H101J C CAPACITOR 100pF 50V JC510 CK73HB1E104K C CAPACITOR 0.10uF 25V KC511 CK73HB1E104K C CAPACITOR 0.10uF 25V KC514 CK73HBB1H102K C CAPACITOR 1000pF 50V K
Symbol No. Part No. Part Name Description Local
(No.RA054<Rev.001>)3-13
C515 CK73HB1C105K C CAPACITOR 1.0uF 16V KC516 C93-1959-05 C CAPACITOR 0.1uF 16VC517 CK73HB1C105K C CAPACITOR 1.0uF 16V KC518 CC73HCH1H101J C CAPACITOR 100pF 50V JC519 CK73HB1E104K C CAPACITOR 0.10uF 25V KC520 CK73HB1E104K C CAPACITOR 0.10uF 25V KC521 CK73HB1E104K C CAPACITOR 0.10uF 25V KC522 CK73HB1H103K C CAPACITOR 10000pF 50V KC523 CK73HBB1H102K C CAPACITOR 1000pF 50V KC524 CC73HCH1H470G C CAPACITOR 47pF 50V GC525 CC73HCH1H470G C CAPACITOR 47pF 50V GC526 CK73HB1C105K C CAPACITOR 1.0uF 16V KC527 CK73HB1E104K C CAPACITOR 0.10uF 25V KC528 CK73HB1C105K C CAPACITOR 1.0uF 16V KC605 CK73HB1H103K C CAPACITOR 10000pF 50V KC606 CK73HB1H103K C CAPACITOR 10000pF 50V KC607 C93-1959-05 C CAPACITOR 0.1uF 16VC608 CK73HB1H103K C CAPACITOR 10000pF 50V KC609 CK73GB1H105K C CAPACITOR 1uF 50V KC610 CK73GB1H105K C CAPACITOR 1uF 50V KC611 CK73GB1H105K C CAPACITOR 1uF 50V KC612 CK73GB1H105K C CAPACITOR 1uF 50V KC613 CK73HBB1H102K C CAPACITOR 1000pF 50V KC614 CC73HCH1H101J C CAPACITOR 100pF 50V JC615 CC73HCH1H101J C CAPACITOR 100pF 50V JC616 CC73HCH1H101J C CAPACITOR 100pF 50V JC617 CC73HCH1H101J C CAPACITOR 100pF 50V JC618 CC73HCH1H101J C CAPACITOR 100pF 50V JC619 CC73HCH1H101J C CAPACITOR 100pF 50V JC620 CC73HCH1H101J C CAPACITOR 100pF 50V JC621 CK73HBB1E223K C CAPACITOR 0.022uF 25V KC622 CC73HCH1H101J C CAPACITOR 100pF 50V JC623 CC73HCH1H101J C CAPACITOR 100pF 50V JC624 CC73HCH1H101J C CAPACITOR 100pF 50V JC625 CC73HCH1H101J C CAPACITOR 100pF 50V JC626 CK73GB1H105K C CAPACITOR 1uF 50V KC627 CK73HB1A224K C CAPACITOR 0.22uF 10V KC628 CK73HB1A224K C CAPACITOR 0.22uF 10V KC629 CK73HBB1H102K C CAPACITOR 1000pF 50V KC630 CK73HBB1H102K C CAPACITOR 1000pF 50V KC631 CK73GB1H105K C CAPACITOR 1uF 50V KC632 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC633 C93-1959-05 C CAPACITOR 0.1uF 16VC634 C93-1959-05 C CAPACITOR 0.1uF 16VC635 CK73HB1H103K C CAPACITOR 10000pF 50V KC636 CK73GB0J106K C CAPACITOR 10uF 6.3V KC637 CK73GB0J106K C CAPACITOR 10uF 6.3V KC638 C93-1959-05 C CAPACITOR 0.1uF 16VC639 CK73HB1C105K C CAPACITOR 1.0uF 16V KC640 C93-1959-05 C CAPACITOR 0.1uF 16VC641 C93-1959-05 C CAPACITOR 0.1uF 16VC642 C93-1959-05 C CAPACITOR 0.1uF 16VC643 C93-1959-05 C CAPACITOR 0.1uF 16VC644 C93-1959-05 C CAPACITOR 0.1uF 16VC645 CK73HB1E104K C CAPACITOR 0.10uF 25V KC646 CK73GB0J106K C CAPACITOR 10uF 6.3V KC647 CK73HB1C105K C CAPACITOR 1.0uF 16V KC648 C93-1959-05 C CAPACITOR 0.1uF 16VC649 CK73HB1C105K C CAPACITOR 1.0uF 16V KC650 C93-1959-05 C CAPACITOR 0.1uF 16VC651 CC73JCH1H101J C CAPACITOR 100pF 50V JC652 CK73HB1C105K C CAPACITOR 1.0uF 16V KC653 CK73HBB1E223K C CAPACITOR 0.022uF 25V KC655 CK73HB1C105K C CAPACITOR 1.0uF 16V KC656 CK73GB0J106K C CAPACITOR 10uF 6.3V KC657 CK73HB1E104K C CAPACITOR 0.10uF 25V KC658 CC73HCH1H680J C CAPACITOR 68pF 50V JC659 CK73HB1C105K C CAPACITOR 1.0uF 16V KC660 CK73HBB1H102K C CAPACITOR 1000pF 50V KC661 CK73HB1C105K C CAPACITOR 1.0uF 16V KC663 CK73HBB1H471K C CAPACITOR 470pF 50V KC664 CK73GB1H105K C CAPACITOR 1uF 50V KC665 CK73GXR1C225K C CAPACITOR 2.2uF 16V K
R2 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR3 RK73HB1J000J MG RESISTOR 0Ω 1/16W J 3820HGK,3820HK
R4 RK73HB1J000J MG RESISTOR 0Ω 1/16W J 3820E,3820GE,3820HGK2,3820HK2
Symbol No. Part No. Part Name Description Local
R5 R92-1061-05 C RESISTOR 0.008ΩR21 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR22 RK73HH1J104D MG RESISTOR 100kΩ 1/16W DR23 RK73HH1J104D MG RESISTOR 100kΩ 1/16W DR24 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR25 RK73HH1J104D MG RESISTOR 100kΩ 1/16W DR26 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR27 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR28 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR29 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR30 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR31 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR32 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR33 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR34 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR35 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR36 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR37 RK73JB1H472J MG RESISTOR 4.7kΩ 1/20W JR38 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR39 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR40 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR41 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR42 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR43 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR44 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR45 RK73HH1J473D MG RESISTOR 47kΩ 1/16W DR46 RK73HH1J113D MG RESISTOR 11kΩ 1/16W DR47 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR48 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR49 RK73HB1J224J MG RESISTOR 220kΩ 1/16W JR50 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR51 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR52 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR53 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR54 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR55 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR56 RK73HB1J124J MG RESISTOR 120kΩ 1/16W JR57 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR58 RK73HH1J303D MG RESISTOR 30kΩ 1/16W DR59 RK73HH1J154D MG RESISTOR 150kΩ 1/16W DR60 RK73HH1J113D MG RESISTOR 11kΩ 1/16W DR61 RK73HH1J103D MG RESISTOR 10kΩ 1/16W DR62 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR63 RK73HH1J113D MG RESISTOR 11kΩ 1/16W DR64 R92-3769-05 MG RESISTOR 10Ω 0.25WR65 R92-3769-05 MG RESISTOR 10Ω 0.25WR66 RK73HB1J334J MG RESISTOR 330kΩ 1/16W JR67 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR68 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR69 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR70 RK73HH1J273D MG RESISTOR 27kΩ 1/16W DR71 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR72 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR73 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR74 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR75 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR76 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR77 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR78 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR79 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR80 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR81 RK73FB2B2R7J MG RESISTOR 2.7Ω 1/8W JR82 RK73FB2B3R3J MG RESISTOR 3.3Ω 1/8W JR83 RK73HH1J152D MG RESISTOR 1.5kΩ 1/16W DR84 RK73HH1J472D MG RESISTOR 4.7kΩ 1/16W DR103 RK73HB1J392J MG RESISTOR 3.9kΩ 1/16W JR104 RK73HB1J182J MG RESISTOR 1.8kΩ 1/16W J
R105 RK73HB1J680J MG RESISTOR 68Ω 1/16W J3820E,3820GE,3820HGK2,3820HK2
R105 RK73HB1J101J MG RESISTOR 100Ω 1/16W J 3820HGK,3820HKR106 RK73HB1J821J MG RESISTOR 820Ω 1/16W J 3820HGK,3820HKR108 RK73HB1J000J MG RESISTOR 0Ω 1/16W J 3820HGK,3820HKR109 RK73HB1J000J MG RESISTOR 0Ω 1/16W J 3820HGK,3820HKR110 RK73HB1J000J MG RESISTOR 0Ω 1/16W J 3820HGK,3820HKR111 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR112 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR113 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR114 RK73HB1J223J MG RESISTOR 22kΩ 1/16W J
Symbol No. Part No. Part Name Description Local
3-14(No.RA054<Rev.001>)
R115 RK73HB1J124J MG RESISTOR 120kΩ 1/16W JR116 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR117 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR118 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR119 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR120 RK73HB1J221J MG RESISTOR 220Ω 1/16W JR121 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR122 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR123 RK73HH1J391D MG RESISTOR 390Ω 1/16W DR124 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR125 RK73HB1J106J MG RESISTOR 10MΩ 1/16W JR126 RK73HB1J392J MG RESISTOR 3.9kΩ 1/16W JR127 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR128 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR129 RK73HB1J182J MG RESISTOR 1.8kΩ 1/16W J
R130 RK73HB1J680J MG RESISTOR 68Ω 1/16W J3820E,3820GE,3820HGK2,3820HK2
R130 RK73HB1J101J MG RESISTOR 100Ω 1/16W J 3820HGK,3820HKR131 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR132 RK73HB1J123J MG RESISTOR 12kΩ 1/16W JR133 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR134 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR135 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR136 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR137 RN73HH1J151D MG RESISTOR 150Ω 0.063W DR138 RN73HH1J100D MF RESISTOR 10Ω 0.063W DR139 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR140 RK73HB1J182J MG RESISTOR 1.8kΩ 1/16W JR141 RK73HB1J272J MG RESISTOR 2.7kΩ 1/16W JR142 RK73HB1J560J MG RESISTOR 56Ω 1/16W JR143 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR145 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR146 RK73HB1J000J MG RESISTOR 0Ω 1/16W J 3820HGK,3820HKR147 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR203 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR204 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR211 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR212 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR213 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR214 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR215 RK73HB1J390J MG RESISTOR 39Ω 1/16W JR216 RK73HB1J390J MG RESISTOR 39Ω 1/16W JR217 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR218 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR219 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR220 RK73HB1J121J MG RESISTOR 120Ω 1/16W JR221 RK73HB1J822J MG RESISTOR 8.2kΩ 1/16W JR222 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR223 RK73HB1J390J MG RESISTOR 39Ω 1/16W JR224 RK73HB1J390J MG RESISTOR 39Ω 1/16W JR225 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR226 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR227 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR228 RK73HB1J392J MG RESISTOR 3.9kΩ 1/16W JR229 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR230 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR231 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR233 RK73GB2A151J MG RESISTOR 150Ω 1/10W JR235 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR238 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR239 RK73GB2A271J MG RESISTOR 270Ω 1/10W JR240 RK73GB2A390J MG RESISTOR 39Ω 1/10W JR241 RK73HB1J272J MG RESISTOR 2.7kΩ 1/16W JR242 RK73GB2A271J MG RESISTOR 270Ω 1/10W JR243 RK73GB2A390J MG RESISTOR 39Ω 1/10W JR244 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR245 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR247 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR248 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR250 RK73HB1J124J MG RESISTOR 120kΩ 1/16W JR251 RK73HB1J153J MG RESISTOR 15kΩ 1/16W JR256 RK73GB2A391J MG RESISTOR 390Ω 1/10W JR258 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR259 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR260 RK73HB1J124J MG RESISTOR 120kΩ 1/16W JR261 RK73HB1J470J MG RESISTOR 47Ω 1/16W J
R262 RK73FB2B101J MG RESISTOR 100Ω 1/8W J3820E,3820GE,3820HGK2,3820HK2
Symbol No. Part No. Part Name Description Local
R262 RK73FB2B910J MG RESISTOR 91Ω 1/8W J 3820HGK,3820HKR265 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR266 RK73HB1J274J MG RESISTOR 270kΩ 1/16W JR267 RK73HB1J392J MG RESISTOR 3.9kΩ 1/16W JR268 RK73GB2A560J MG RESISTOR 56Ω 1/10W J
R269 RK73FB2B820J MG RESISTOR 82Ω 1/8W J3820E,3820GE,3820HGK2,3820HK2
R269 RK73FB2B101J MG RESISTOR 100Ω 1/8W J 3820HGK,3820HKR270 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR271 RK73HB1J102J MG RESISTOR 1kΩ 1/16W J
R272 RK73GB2A560J MG RESISTOR 56Ω 1/10W J3820E,3820GE,3820HGK2,3820HK2
R273 RK73HB1J183J MG RESISTOR 18kΩ 1/16W JR274 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR275 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR276 RK73PB2H560J MG RESISTOR 56Ω 1/2W JR277 RK73PB2H560J MG RESISTOR 56Ω 1/2W JR278 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR280 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR281 RK73GB2A560J MG RESISTOR 56Ω 1/10W JR282 RK73HB1J333J MG RESISTOR 33kΩ 1/16W JR302 RK73HB1J821J MG RESISTOR 820Ω 1/16W JR303 RK73HB1J821J MG RESISTOR 820Ω 1/16W JR304 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR305 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR307 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR308 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR309 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR310 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR311 RK73HH1J391D MG RESISTOR 390Ω 1/16W DR312 RK73HB1J5R6J MG RESISTOR 5.6Ω 1/16W JR313 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR314 RK73HB1J120J MG RESISTOR 12Ω 1/16W JR315 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR316 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR317 RK73HH1J473D MG RESISTOR 47kΩ 1/16W DR318 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR319 RK73HH1J273D MG RESISTOR 27kΩ 1/16W DR320 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR321 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR322 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR323 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR324 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR325 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR326 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR407 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR408 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR416 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR418 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR420 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR421 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR422 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR423 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR424 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR425 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR426 RK73HB1J153J MG RESISTOR 15kΩ 1/16W JR427 RK73HB1J333J MG RESISTOR 33kΩ 1/16W JR428 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR429 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR431 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR432 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR433 RK73JB1H472J MG RESISTOR 4.7kΩ 1/20W JR434 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR435 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR436 RK73JB1H105J MG RESISTOR 1MΩ 1/20W JR437 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR438 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR439 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR440 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR441 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR442 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR443 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR444 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR445 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR446 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR447 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR448 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR449 RK73JB1H220J MG RESISTOR 22Ω 1/20W J
Symbol No. Part No. Part Name Description Local
(No.RA054<Rev.001>)3-15
R450 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR451 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR452 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR453 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR454 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR455 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR456 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR457 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR458 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR459 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR460 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR461 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR462 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR463 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR464 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR465 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR466 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR467 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR468 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR469 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR470 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR471 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR472 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR473 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR474 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR475 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR476 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR477 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR478 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR479 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR480 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR481 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR482 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR483 RK73GH2A49R9D MG RESISTOR 49.9Ω 1/10W DR484 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR485 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR486 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR487 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR488 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR489 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR490 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR491 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR492 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR493 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR494 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR495 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR496 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR497 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR498 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR499 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR500 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR501 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR502 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR503 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR504 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR505 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR506 RK73HH1J104D MG RESISTOR 100kΩ 1/16W DR507 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR508 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR509 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR511 RK73HB1J333J MG RESISTOR 33kΩ 1/16W JR512 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR513 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR514 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR516 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR517 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR518 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR519 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR520 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR522 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR523 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR524 RK73FB2B332J MG RESISTOR 3.3kΩ 1/8W JR525 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR526 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR527 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR528 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR529 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR530 RK73HH1J223D MG RESISTOR 22kΩ 1/16W D
Symbol No. Part No. Part Name Description Local
R531 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR532 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR533 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR534 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR535 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR536 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR537 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR538 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR539 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR613 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR614 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR615 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR616 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR617 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR618 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR619 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR620 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR621 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR622 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR623 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR624 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR625 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR626 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR627 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR628 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR629 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR630 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR631 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR632 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR633 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR634 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR635 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR636 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR637 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR638 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR639 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR640 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR641 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR642 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR643 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR644 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR645 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR646 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR647 RK73HB1J682J MG RESISTOR 6.8kΩ 1/16W JR648 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR649 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR650 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR651 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR652 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR653 RK73HB1J682J MG RESISTOR 6.8kΩ 1/16W JR654 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR655 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR656 RK73FB2B102J MG RESISTOR 1kΩ 1/8W JR657 RK73FB2B102J MG RESISTOR 1kΩ 1/8W JR658 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR659 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR660 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR661 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR662 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR663 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR664 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR665 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR666 RK73HB1J683J MG RESISTOR 68kΩ 1/16W JR667 RK73HB1J123J MG RESISTOR 12kΩ 1/16W JR668 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR669 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR670 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR671 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR672 RK73HH1J273D MG RESISTOR 27kΩ 1/16W DR673 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR674 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR675 RK73HB1J682J MG RESISTOR 6.8kΩ 1/16W JR676 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR677 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR678 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR679 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR680 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR681 RK73HH1J152D MG RESISTOR 1.5kΩ 1/16W D
Symbol No. Part No. Part Name Description Local
3-16(No.RA054<Rev.001>)
L1 L34-4902-05 AIR CORE COIL
L2 L34-4758-05 AIR CORE COIL3820E,3820GE,3820HGK2,3820HK2
L2 L34-4743-05 AIR CORE COIL 3820HGK,3820HKL3 L34-4758-05 AIR CORE COILL4 L34-4758-05 AIR CORE COILL5 L34-4743-05 AIR CORE COILL6 L34-4848-05 AIR CORE COILL7 L34-4610-15 AIR CORE COILL11 LB73G0AK-001 CHIP FERRITEL12 LR79Z0FQ100M CHIP INDUCTORL13 LB73G0AM-004 CHIP FERRITEL14 LR79Z0AA150M CHIP INDUCTORL15 LB73G0AM-004 CHIP FERRITEL16 LB73G0AK-001 CHIP FERRITEL17 LB73H0AV-002 CHIP FERRITEL18 LB73H0AV-002 CHIP FERRITEL19 LB73G0AK-001 CHIP FERRITE
L101 LK73H0AM12NJ M.CHIP INDUCTOR 12nH3820E,3820GE,3820HGK2,3820HK2
L101 LK73H0AM8N2J M.CHIP INDUCTOR 8.2nH 3820HGK,3820HK
L102 LK73H0BX5N1B M.CHIP INDUCTOR3820E,3820GE,3820HGK2,3820HK2
L103 LK73H0AM8N2J M.CHIP INDUCTOR 8.2nH3820E,3820GE,3820HGK2,3820HK2
L104 LK73H0BX5N1B M.CHIP INDUCTOR3820E,3820GE,3820HGK2,3820HK2
L105 LK73H0AM8N2J M.CHIP INDUCTOR 8.2nH3820E,3820GE,3820HGK2,3820HK2
L106 LK73H0AM15NJ M.CHIP INDUCTOR 15nH3820E,3820GE,3820HGK2,3820HK2
L106 LK73H0AM8N2J M.CHIP INDUCTOR 8.2nH 3820HGK,3820HKL107 LB73H0AV-003 CHIP FERRITEL108 L41-2785-53 CHIP INDUCTORL109 LB73H0AV-003 CHIP FERRITEL110 L41-2785-53 CHIP INDUCTORL111 L41-2785-53 CHIP INDUCTORL112 L41-2785-53 CHIP INDUCTORL113 L41-2785-53 CHIP INDUCTORL115 L41-2785-53 CHIP INDUCTORL116 L41-2785-53 CHIP INDUCTORL117 LB73H0AY-004 CHIP FERRITE
L118 LK73H0AM15NJ M.CHIP INDUCTOR 15nH3820E,3820GE,3820HGK2,3820HK2
L118 LK73H0AM10NJ M.CHIP INDUCTOR 10nH 3820HGK,3820HKL119 LB73H0AY-004 CHIP FERRITE
L120 LK73H0BX3N0B M.CHIP INDUCTOR3820E,3820GE,3820HGK2,3820HK2
L120 LK73H0AM2N7S M.CHIP INDUCTOR 2.7nH 3820HGK,3820HK
L121 LK73H0BX39NG M.CHIP INDUCTOR3820E,3820GE,3820HGK2,3820HK2
L121 LK73H0AM33NJ M.CHIP INDUCTOR 33nH 3820HGK,3820HK
L122 LK73H0BX1N8B M.CHIP INDUCTOR3820E,3820GE,3820HGK2,3820HK2
L122 LK73H0AM1N8S M.CHIP INDUCTOR 1.8nH 3820HGK,3820HK
L123 LK73H0BX39NG M.CHIP INDUCTOR3820E,3820GE,3820HGK2,3820HK2
L123 LK73H0AM33NJ M.CHIP INDUCTOR 33nH 3820HGK,3820HK
L124 LK73H0BX3N0B M.CHIP INDUCTOR3820E,3820GE,3820HGK2,3820HK2
L124 LK73H0AM2N7S M.CHIP INDUCTOR 2.7nH 3820HGK,3820HKL207 LB73H0AY-004 CHIP FERRITEL208 LB73H0AY-004 CHIP FERRITEL209 LK73H0AM15NJ M.CHIP INDUCTOR 15nHL210 LK73H0AMR12J M.CHIP INDUCTOR 0.12uHL211 LK73H0AM15NJ M.CHIP INDUCTOR 15nHL212 LK73H0AM15NJ M.CHIP INDUCTOR 15nHL213 LK73H0AM8N2J M.CHIP INDUCTOR 8.2nH
L214 L41-1575-53 CHIP INDUCTOR3820E,3820GE,3820HGK2,3820HK2
L214 L41-1275-53 CHIP INDUCTOR 3820HGK,3820HKL215 LB73F0AW-002 CHIP FERRITE
L216 L41-1575-53 CHIP INDUCTOR3820E,3820GE,3820HGK2,3820HK2
L216 L41-1275-53 CHIP INDUCTOR 3820HGK,3820HKL217 LB73H0AV-003 CHIP FERRITEL218 LB73G0BA-004 CHIP FERRITE
Symbol No. Part No. Part Name Description Local
L219 LB73Z0DF-001 CHIP FERRITEL220 LB73Z0DF-001 CHIP FERRITEL221 LB73Z0DF-001 CHIP FERRITEL222 L41-4775-53 CHIP INDUCTOR
L223 LR77Z0AA68NJ CHIP INDUCTOR 68nH3820E,3820GE,3820HGK2,3820HK2
L223 LR77Z0AAR12J CHIP INDUCTOR 3820HGK,3820HKL224 LR79G0GK82NG CHIP INDUCTORL225 LB73H0AY-004 CHIP FERRITEL226 LB73H0AV-003 CHIP FERRITEL227 LR79G0GK3N9B CHIP INDUCTORL302 LK73H0AM33NJ M.CHIP INDUCTOR 33nHL303 LR79G0CQ18NG CHIP INDUCTORL304 LR79G0CQ12NG CHIP INDUCTORL305 LR79G0CQ22NG CHIP INDUCTOR 22nHL306 LR79G0CQ3N9C CHIP INDUCTORL307 LR79G0CQ39NG CHIP INDUCTORL308 LR79G0CQ39NG CHIP INDUCTORL309 LR79G0CQ39NG CHIP INDUCTORL310 LR79G0CQ22NG CHIP INDUCTOR 22nHL311 LR79G0CQR22G CHIP INDUCTORL312 LK73H0AM33NJ M.CHIP INDUCTOR 33nHL313 LR79G0CQ18NG CHIP INDUCTORL314 LK73H0AMR27J M.CHIP INDUCTORL401 LB73G0AK-001 CHIP FERRITEL402 LB73H0AV-003 CHIP FERRITEL403 LB73G0AK-001 CHIP FERRITEL404 LR77Z0AE4R7J CHIP INDUCTOR 4.7uHL405 LB73G0AM-004 CHIP FERRITEL406 L92-1101-05 CHIP FERRITEL407 L92-1101-05 CHIP FERRITEL408 L92-1101-05 CHIP FERRITEL409 L92-1101-05 CHIP FERRITEL410 LB73G0AK-001 CHIP FERRITEL411 LB73G0AK-001 CHIP FERRITEL412 LB73G0AK-001 CHIP FERRITEL413 LB73G0AK-001 CHIP FERRITEL414 LB73H0AV-002 CHIP FERRITEL415 L79-1984-05 FILTERL416 L79-1984-05 FILTERL417 LB73H0AY-002 CHIP FERRITEL418 LB73H0AY-002 CHIP FERRITEL419 L79-1984-05 FILTERL420 L92-1101-05 CHIP FERRITEL601 LB73H0AV-003 CHIP FERRITEL602 LB73H0AV-003 CHIP FERRITEL603 LB73H0AV-003 CHIP FERRITE
CN1 EC720AA-0560A FFC FPC CONNECN2 E40-6862-05 F.C.CONNECTORCN3 J19-5386-05 HOLDERCP301 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP302 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP303 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP401 RK74HB1J103J NET RESISTOR 10kΩ 1/16W JCP402 RK74HB1J222J NET RESISTOR 2.2kΩ 1/16W JCP403 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP404 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP405 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP406 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP407 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP408 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP409 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP410 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP411 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP412 RK74HB1J470J NET RESISTOR 47Ω 1/16W JCP413 RK74HB1J470J NET RESISTOR 47Ω 1/16W JCP414 RK74HB1J470J NET RESISTOR 47Ω 1/16W JCP601 RK74HB1J472J NET RESISTOR 4.7kΩ 1/16W JCP602 RK74HB1J472J NET RESISTOR 4.7kΩ 1/16W JCP604 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP605 RK74HB1J101J NET RESISTOR 100Ω 1/16W JE11 F1B-0085-00 SHIELDING CASEE101 F1B-0085-00 SHIELDING CASEF1 F53-0286-05 FUSEF2 F53-0286-05 FUSEF3 F53-0286-05 FUSEF4 FZA10BS-5R0 FUSE (CC)
Symbol No. Part No. Part Name Description Local
(No.RA054<Rev.001>)3-17
SUB UNITXC3-050M-00
Block No. [0][3]
F5 FZA10BS-5R0 FUSE (CC)F6 F53-0286-05 FUSE
IC201 RA60H3847-501 MOS IC3820E,3820GE,3820HGK2,3820HK2
IC201 RA60H4452-501 MOS IC 3820HGK,3820HKIC601 LA4631VC-XE ANALOG ICJ1 E58-0567-05 SUB SOCKET DJ2 E1B-0001-00 3.5D PHONE JACKTH201 NCU15WF104F6S N THERMISTORTH202 NCU15WF104F6S N THERMISTORTH203 NCU15WF104F6S N THERMISTORTH401 NCU15WF104F6S N THERMISTORX401 L7H-0076-00 TCXOX402 L77-1802-05 QUARTZ CRYSTAL
Symbol No. Part No. Part Name Description Local
IC1 MM3404A50URE ICIC3 TC7WH126FK ICIC4 TC7WT125FUF ICIC5 BD11600NUX ICIC6 TC35894FG IC
Q1 SSM3K15AMFV FETQ2 SSM6N37FE FETQ3 LTC014EEBFS8 DIGI TRANSISTORQ4 LTC014EEBFS8 DIGI TRANSISTORQ6 LTC014EEBFS8 DIGI TRANSISTORQ8 SSM6N37FE FET
D1 SPC10501A01 VARISTORD2 SPC10501A01 VARISTORD3 B30-2365-05 LEDD4 B30-2365-05 LEDD5 B30-2365-05 LEDD6 B30-2365-05 LEDD9 NSSW206C-T865 LEDD10 NSSW206C-T865 LEDD11 B30-2365-05 LEDD12 B30-2365-05 LEDD15 NSSW206C-T865 LEDD16 NSSW206C-T865 LEDD17 B30-2365-05 LEDD18 B30-2365-05 LEDD20 B30-2364-05 LEDD21 EDZV6.2B ZENER DIODED22 RB521CM-30 DIODED24 EDZV6.8B ZENER DIODED26 RSB12Z ZENER DIODED27 MINISMDC020F VARISTORD28 EMZ6.8N ZENER DIODED30 EDZV6.8B ZENER DIODED32 RSB12Z ZENER DIODED33 B30-2365-05 LEDD34 B30-2365-05 LED
C1 CK73HBB1H102K C CAPACITOR 1000pF 50V KC2 CC73HCH1H101J C CAPACITOR 100pF 50V JC3 CK73HB1E104K C CAPACITOR 0.10uF 25V KC6 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC7 CC73HCH1H101J C CAPACITOR 100pF 50V JC8 CC73HCH1H101J C CAPACITOR 100pF 50V JC9 CC73HCH1H101J C CAPACITOR 100pF 50V JC11 CC73HCH1H101J C CAPACITOR 100pF 50V JC12 CC73HCH1H101J C CAPACITOR 100pF 50V JC13 CK73HB1E104K C CAPACITOR 0.10uF 25V KC14 CK73HB1E104K C CAPACITOR 0.10uF 25V KC15 CK73HB1E104K C CAPACITOR 0.10uF 25V KC16 CK73HBB1H102K C CAPACITOR 1000pF 50V K
Symbol No. Part No. Part Name Description Local
C17 CC73HCH1H101J C CAPACITOR 100pF 50V JC20 CK73HBB1H102K C CAPACITOR 1000pF 50V KC21 CK73HBB1H102K C CAPACITOR 1000pF 50V KC22 CK73HBB1H102K C CAPACITOR 1000pF 50V KC24 CC73HCH1H101J C CAPACITOR 100pF 50V JC25 CC73HCH1H101J C CAPACITOR 100pF 50V JC26 CC73HCH1H101J C CAPACITOR 100pF 50V JC28 CK73GB1E105K C CAPACITOR 1uF 25V KC30 CK73GB1E105K C CAPACITOR 1uF 25V KC33 CK73HB1E104K C CAPACITOR 0.10uF 25V KC34 CK73HB1E104K C CAPACITOR 0.10uF 25V KC35 CK73HB1E104K C CAPACITOR 0.10uF 25V KC36 CK73GB1E105K C CAPACITOR 1uF 25V KC37 CK73HB1E104K C CAPACITOR 0.10uF 25V KC38 CK73HBB1E103K C CAPACITOR 0.01uF 25V KC39 CC73HCH1H101J C CAPACITOR 100pF 50V JC40 CK73HBB1H102K C CAPACITOR 1000pF 50V KC41 CK73HB1E104K C CAPACITOR 0.10uF 25V KC45 CK73HBB1H102K C CAPACITOR 1000pF 50V KC46 CK73HBB1H102K C CAPACITOR 1000pF 50V KC47 CK73HBB1H102K C CAPACITOR 1000pF 50V KC49 CC73HCH1H101J C CAPACITOR 100pF 50V JC50 CC73HCH1H101J C CAPACITOR 100pF 50V JC51 CC73HCH1H101J C CAPACITOR 100pF 50V JC52 CC73HCH1H101J C CAPACITOR 100pF 50V JC53 CC73HCH1H101J C CAPACITOR 100pF 50V JC54 CC73HCH1H101J C CAPACITOR 100pF 50V JC55 CC73HCH1H101J C CAPACITOR 100pF 50V JC56 CC73HCH1H101J C CAPACITOR 100pF 50V JC57 CC73HCH1H101J C CAPACITOR 100pF 50V JC58 CC73HCH1H101J C CAPACITOR 100pF 50V JC59 CK73HBB1H102K C CAPACITOR 1000pF 50V KC61 CK73HB1E104K C CAPACITOR 0.10uF 25V KC62 CK73HB1E104K C CAPACITOR 0.10uF 25V KC64 CK73GB1E105K C CAPACITOR 1uF 25V KC65 CK73GB1E105K C CAPACITOR 1uF 25V KC66 CK73GB1E105K C CAPACITOR 1uF 25V KC67 CC73HCH1H101J C CAPACITOR 100pF 50V JC68 CK73GB1E105K C CAPACITOR 1uF 25V KC70 CC73HCH1H470J C CAPACITOR 47pF 50V JC71 CC73HCH1H470J C CAPACITOR 47pF 50V JC72 CC73HCH1H470J C CAPACITOR 47pF 50V JC73 CC73HCH1H470J C CAPACITOR 47pF 50V J
R1 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR2 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR4 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR5 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR6 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR7 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR8 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR9 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR10 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR11 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR12 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR13 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR14 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR15 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR16 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR17 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR18 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR19 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR20 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR21 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR22 RK73GB2A181J MG RESISTOR 180Ω 1/10W JR23 RK73GB2A181J MG RESISTOR 180Ω 1/10W JR24 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR25 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR27 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR28 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR29 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR30 RK73GB2A181J MG RESISTOR 180Ω 1/10W JR31 RK73GB2A181J MG RESISTOR 180Ω 1/10W JR32 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR33 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR36 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR37 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR38 RK73HB1J681J MG RESISTOR 680Ω 1/16W J
Symbol No. Part No. Part Name Description Local
3-18(No.RA054<Rev.001>)
MODULE UNITXC2-0040-10 (NX-3720GE,NX-3720HGK,NX-3820GE,NX-3820HGK,NX-3820HGK2)*Note : This part cannot be replaced.Therefore, this part is not supplied as a service part.
Block No. [0][4]
R39 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR40 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR41 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR42 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR43 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR44 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR45 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR46 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR47 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR48 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR49 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR50 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR51 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR56 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR57 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR58 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR60 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR61 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR62 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR63 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR64 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR66 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR67 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR68 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR69 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR70 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR71 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR72 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR73 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR74 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR75 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR77 RK73GB2A680J MG RESISTOR 68Ω 1/10W JR79 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR80 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR81 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR82 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR83 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR84 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR85 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR86 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR87 RK73GB2A000J MG RESISTOR 0Ω 1/10W J
L1 LB73G0AM-004 CHIP FERRITEL2 LB73G0AM-004 CHIP FERRITEL3 LB73H0AV-003 CHIP FERRITEL6 LB73H0AV-003 CHIP FERRITEL8 LB73H0AV-003 CHIP FERRITEL9 LB73H0AV-003 CHIP FERRITEL10 LB73H0AV-003 CHIP FERRITEL11 LB73G0AM-004 CHIP FERRITEL12 LB73G0AM-004 CHIP FERRITEL13 LB73H0AV-003 CHIP FERRITEL14 LB73G0AM-004 CHIP FERRITE
CN3 EC720AK-0512A FFC FPC CONNECN5 E41-2671-05 PIN ASSYCN6 EC720AA-0523A FFC FPC CONNECN7 EC710AM-0560A FFC FPC CONNEJ1 E58-0535-05 MODULAR JACK
Symbol No. Part No. Part Name Description Local
IC1 74AVC4TD245GU ICIC2 BU18TD2WNVX ICIC3 XC6209B332D-G IC
Symbol No. Part No. Part Name Description Local
IC4 NJM2878F4-33 ICIC5 ------------ IC *NoteIC6 74AVC4TD245GU ICIC7 74AVC4TD245GU IC
Q1 EM6M2 FET
D17 RN262CS DIODED18 RN262CS DIODE
C1 CK73HB1A474K C CAPACITOR 0.47uF 10V KC2 CK73HB1A474K C CAPACITOR 0.47uF 10V KC3 CK73HB1E104K C CAPACITOR 0.10uF 25V KC4 CK73HB1E104K C CAPACITOR 0.10uF 25V KC5 CK73HB1A105K C CAPACITOR 1uF 10V KC6 CK73HB1A474K C CAPACITOR 0.47uF 10V KC7 CK73HB1A474K C CAPACITOR 0.47uF 10V KC8 CC73HCH1H220J C CAPACITOR 22pF 50V JC9 CC73HCH1H100B C CAPACITOR 10pF 50V BC10 CK73HB1A105K C CAPACITOR 1uF 10V KC11 CK73HB1E104K C CAPACITOR 0.10uF 25V KC12 CK73HB1E104K C CAPACITOR 0.10uF 25V KC13 CK73HB1E104K C CAPACITOR 0.10uF 25V KC14 CK73HB1E104K C CAPACITOR 0.10uF 25V KC15 CK73HB1A105K C CAPACITOR 1uF 10V KC16 CK73HB1E104K C CAPACITOR 0.10uF 25V KC17 CK73HB1E104K C CAPACITOR 0.10uF 25V KC18 CC73HCH1H180J C CAPACITOR 18pF 50V JC19 CC73HCH1H180J C CAPACITOR 18pF 50V JC20 CK73HB1A105K C CAPACITOR 1uF 10V KC21 CK73HB1A105K C CAPACITOR 1uF 10V KC22 CK73HB1E104K C CAPACITOR 0.10uF 25V KC23 CK73HBB1H102K C CAPACITOR 1000pF 50V KC24 CK73HB1E104K C CAPACITOR 0.10uF 25V KC25 CK73HBB1H102K C CAPACITOR 1000pF 50V KC26 CK73HBB1H102K C CAPACITOR 1000pF 50V KC27 CK73HBB1H102K C CAPACITOR 1000pF 50V KC28 CK73HB1E104K C CAPACITOR 0.10uF 25V KC29 CK73HB1E104K C CAPACITOR 0.10uF 25V KC30 CK73HB1E104K C CAPACITOR 0.10uF 25V KC31 CK73HB1A105K C CAPACITOR 1uF 10V KC32 CK73HB1E104K C CAPACITOR 0.10uF 25V KC33 CK73HB1E104K C CAPACITOR 0.10uF 25V KC34 CK73HB1E104K C CAPACITOR 0.10uF 25V KC35 CK73HB1E104K C CAPACITOR 0.10uF 25V KC36 CC73HCH1H220J C CAPACITOR 22pF 50V JC37 CC73HCH1H220J C CAPACITOR 22pF 50V JC38 CC73HCH1H2R5B C CAPACITOR 2.5pF 50V BC39 CK73HB1E104K C CAPACITOR 0.10uF 25V KC40 CC73HCH1H180J C CAPACITOR 18pF 50V JC44 CK73HB1E104K C CAPACITOR 0.10uF 25V KC45 CK73HB1E104K C CAPACITOR 0.10uF 25V KC46 CK73HB1E104K C CAPACITOR 0.10uF 25V KC47 CK73HB1E104K C CAPACITOR 0.10uF 25V KC48 CK73HB1E104K C CAPACITOR 0.10uF 25V KC49 CK73HB1E104K C CAPACITOR 0.10uF 25V KC50 CC73HCH1H470J C CAPACITOR 47pF 50V JC68 CC73HCH1H010B C CAPACITOR 1pF 50V B
R1 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR2 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR3 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR4 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR7 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR8 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR9 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR10 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR11 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR12 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR13 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR14 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR15 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR16 RK73EB2E100J MG RESISTOR 10Ω 1/4W JR18 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR19 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR21 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR22 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR23 RK73HB1J000J MG RESISTOR 0Ω 1/16W J
Symbol No. Part No. Part Name Description Local
(No.RA054<Rev.001>)3-19
R24 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR25 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR26 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR27 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR29 RK73HB1J000J MG RESISTOR 0Ω 1/16W J
L1 LB73H0AV-002 CHIP FERRITEL2 LB73G0AK-001 CHIP FERRITEL3 LB73G0BJ-002 CHIP FERRITEL4 L92-0487-05 CHIP FERRITEL5 L92-0487-05 CHIP FERRITEL6 LK73H0AG27NJ M.CHIP INDUCTOR 27nHL7 LK73H0AM10NJ M.CHIP INDUCTOR 10nHL8 L92-0487-05 CHIP FERRITEL9 L7K-0059-00 FILTERL11 L79-1987-05 FILTERL13 L92-0487-05 CHIP FERRITEL14 L92-0487-05 CHIP FERRITEL15 L40-2263-71 CHIP INDUCTOR
CN1 E40-6879-05 F.C.CONNECTORCN5 E0E-0012-00 RF C.RECEPTACLECP1 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP2 RK74HB1J100J NET RESISTOR 10Ω 1/16W JE1 F10-3226-05 SHIELDING CASEX1 L77-3123-05 TCXOX2 L77-3121-05 QUARTZ CRYSTAL
Symbol No. Part No. Part Name Description Local
3-20(No.RA054<Rev.001>)
Packing materials and accessories parts list
Packing and accessoriesBlock No. [M][2][M][M]
Symbol No. Part No. Part Name Description Local
1 H5A-0946-00 ITEM CARTON 2 H1C-0152-00 PACKING FIXTURE (x2) 3 ------------ PROTECTION BAG 4 J19-1584-15 HOLDER ACC 3720HGK,3720HK,3820HGK,3820HGK2,3820HK,3820HK2 5 J29-0726-03 BRACKET ACC 6 T91-0639-85 MICROPHONE KMC-35 3720HGK,3720HK,3820HGK,3820HGK2,3820HK,3820HK2 7 B5A-1680-00 INST.MANUAL 9 LANGUAGES 3720E,3720GE,3820E,3820GE 7 B5A-1562-00 INST.MANUAL 3 LANGUAGES 3720HGK,3720HK,3820HGK,3820HGK2,3820HK,3820HK2 8 ------------ PAMPHLET DOC 3720E,3720GE,3820E,3820GE 9 E30-7523-65 DC CORD ASSY ACC BLADE 10 N99-2039-05 SCREW SET ACC 11 FZB10AU-150 BLADE FUSE 15A BLADE(ACC)(x2)
Block No.M2MM
1
2
2
3
4
5
6 7
9
10
11
8
(No.RA054<Rev.001>)3-21
(No.RA054<Rev.001>)
JKS
Printed in Japan
JVC KENWOOD CorporationCommunications Systems Division