service manual - · pdf filepdp4206em customer model: service manual safety precaution...
TRANSCRIPT
PDP4206EM
Customer Model:
SERVICE MANUAL
Safety Precaution
Technical Specifications
Block Diagram
Circuit Diagram
Basic Operations & Circuit Description
Main IC Specifications
Product Specification of PDP Module
Trouble Shooting Manual of PDP Module
Spare Part List
Exploded View
If you forget your V-Chip Password
Software Upgrade
This manual is the latest at the time of printing, and does notinclude the modification which may be made after the printing,by the constant improvement of product.
Safety Precaution
PRECAUTIONS DURINGSERVICING
1. In addition to safety, other parts and
assemblies are specified for conformance with
such regulations as those applying to spurious
radiation. These must also be replaced only
with specified replacements.
Examples: RF converters, tuner units, antenna
selection switches, RF cables, noise-blocking
capacitors, noise-blocking filters, etc.
2. Use specified internal Wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
3. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulating Tape
2) PVC tubing
3) Spacers (insulating barriers)
4) Insulating sheets for transistors
5) Plastic screws for fixing micro switches
4. When replacing AC primary side components
(transformers, power cords, noise blocking
capacitors, etc.), wrap ends of wires securely
about the terminals before soldering.
5. Make sure that wires do not contact heat
generating parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
6. Check if replaced wires do not contact sharply
edged or pointed parts.
7. Make sure that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
The lightning flash with arrowhead symbol,within an equilateral triangle, is intended toalert the user to the presence of uninsulated“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude toconstitute a risk of electric shock to persons.
The exclamation point within an equilateraltriangle is intended to alert the user to thepresence of important operating andmaintenance (servicing) instructions in theliterature accompanying the appliance.
CAUTION: TO REDUCE THE RISK OFELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLE PARTSINSIDE. REFER SERVICING TO QUALIFIEDSERVICE PERSONNEL ONLY.
CAUTION
RISK OF ELECTRIC SHOCKDO NOT OPEN
MAKE YOUR CONTRIBUTIONTO PROTECT THE
ENVIRONMENTUsed batteries with the ISO symbol
for recycling as well as small accumulators
(rechargeable batteries), mini-batteries (cells) and
starter batteries should not be thrown into the
garbage can.
Please leave them at an appropriate depot.
WARNING:
Before servicing this TV receiver, read the
SAFETY INSTRUCTION and PRODUCT
SAFETY NOTICE.
SAFETY INSTRUCTIONThe service should not be attempted by anyone
unfamiliar with the necessary instructions on this
apparatus. The following are the necessary
instructions to be observed before servicing.
1. An isolation transformer should be connected in
the power line between the receiver and the
AC line when a service is performed on the
primary of the converter transformer of the set.
2. Comply with all caution and safety related
provided on the back of the cabinet, inside the
cabinet, on the chassis or picture tube.
3. To avoid a shock hazard, always discharge the
picture tube's anode to the chassis ground
before removing the anode cap.
4. Completely discharge the high potential voltage
of the picture tube before handling. The picture
tube is a vacuum and if broken, the glass will
explode.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this
apparatus have special safety-related
characteristics.
These characteristics are offer passed
unnoticed by visual spection and the protection
afforded by them cannot necessarily be obtained
by using replacement components rates for a
higher voltage, wattage, etc.
The replacement parts which have these
special safety characteristics are identified by
marks on the schematic diagram and on the parts
list.
Before replacing any of these components,
read the parts list in this manual carefully. The
use of substitute replacement parts which do not
have the same safety characteristics as specified
in the parts list may create shock, fire, or other
hazards.
9. Must be sure that the ground wire of the AC
inlet is connected with the ground of the
apparatus properly.
5. When replacing a MAIN PCB in the cabinet,
always be certain that all protective are
installed properly such as control knobs,
adjustment covers or shields, barriers, isolation
resistor networks etc.
6. When servicing is required, observe the original
lead dressing. Extra precaution should be given
to assure correct lead dressing in the high
voltage area.
7. Keep wires away from high voltage or high
tempera ture components.
8. Before returning the set to the customer,
always perform an AC leakage current check
on the exposed metallic parts of the cabinet,
such as antennas, terminals, screwheads,metal
overlay, control shafts, etc., to be sure the set
is safe to operate without danger of electrical
shock. Plug the AC line cord directly to the
AC outlet (do not use a line isolation
transformer during this check). Use an AC
voltmeter having 5K ohms volt sensitivity or
more in the following manner.
Connect a 1.5K ohm 10 watt resistor paralleled
by a 0.15µF AC type capacitor, between a
good earth ground (water pipe, conductor etc.,)
and the exposed metallic parts, one at a time.
Measure the AC voltage across the combination
of the 1.5K ohm resistor and 0.15 uF
capacitor. Reverse the AC plug at the AC
outlet and repeat the AC voltage measurements
for each exposed metallic part.
The measured voltage must not exceed 0.3V
RMS.
This corresponds to 0.5mA AC. Any value
exceeding this limit constitutes a potential
shock hazard and must be corrected
immediately.
The resistance measurement should be done
between accessible exposed metal parts and
power cord plug prongs with the power switch
"ON". The resistance should be more than
6M ohms.
Good earth groundsuch as the waterpipe, conductor,etc.
Place this probeon each exposedmetallic part
AC VOLTMETER
AC Leakage Current Check
Technical Specifications
MODEL : PDP4206EM
42” Plasma Monitor
DATE FIRST ISSUED
ISSUE
1
RAISED BY
CHECKED BY
NUMBER OF PAGES
9
REVISIONS ISSUED DATE DESCRIPTION RAISED BY :
SPECIFICATION AGREED : SIGNATURE DATE
R & D DEPARTMENT
COMMERCIAL DEPARTMENT
PRODUCTION DEPARTMENT
Q/A DEPARTMENT
CUSTOMER
......................................................................................
......
............................................................................................
.............................................................................................
.............................................................................................
.............................................................................................
..............................
..............................
..............................
..............................
..............................
SPECIFICATION APPROVED : .
SIGNATURE :
DATE :
NOTE : Only documents stamped “Controlled Document” to be used for manufacture of production parts.
Technical Specifications
PDP420
CONTINUATION PAGE
NUMBER 2 OF 9 PAGES
1. Standard Test Conditions All tests shall be performed under the following conditions, unless otherwise specified. 1.1 Ambient light : 150ux (When measuring IB, the ambient luminance ≦0.1Cd/m2)
1.2 Viewing distance : 50cm in front of PDP
1.3 Warm up time : 30 minutes 1.4 PDP Panel facing : no restricted 1.5 Measuring Equipment : PC, Chroma 2225 signal generator (with Chroma digital additional card) or equivalent, Minolta CA100 photometer 1.6 Magnetic field : no restricted 1.7 Control settings : Brightness, Contrast, Tint, Color set at Center(50) 1.8 Power input : 110~120Vac 1.9 Ambient temperature : 20°C ± 5°C (68°F ± 9°F) 1.10 Display mode : 31.5KHz/60Hz (Resolution 852 x 480) 1.11 Other conditions : 1.11.1 With image sticking protection of PDP module, the luminance will descend
by time on a same still screen and rapidly go down in 5 minutes. When measuring the color tracking and luminance of a same still screen, be sure to accomplish the measurement in one minute to ensure its accuracy. 1.11.2 Due to the structure of PDP, the extra-high-bright same screen should not hold over 5 minutes for fear of branding on the panel.
Technical Specifications
PDP4206EM
CONTINUATION PAGE
NUMBER 3 OF 9 PAGES
ELECTRICAL CHARACTERISTICS 2. Power Input 2.1 Voltage : 110 ~120VAC 2.2 Input Current : 3.5 / 1.5A 2.3 Maximum Inrush Current : <30 A (FOR AC110V ONLY) Test condition : Measured when switched off for at least 20 mins 2.4 Frequency : 50Hz to 60Hz(±3Hz) 2.5 Power Consumption : ≤ 330W Test condition : full white display with maximum brightness and contrast 2.6 Power Factor : Meets IEC1000-3-2 2.7 Withstanding voltage : 1.5kVac or 2.2kVdc for 1 sec 3. Display
3.1 Screen Size : 42” Plasma monitor 3.2 Aspect Ratio : 16:9 3.3 Pixel Resolution : 852x480 3.4 Peak Brightness : 1000 cd/m² (Panel module without filter) 3.5 Contrast Ratio (Dark room) : 3000:1 (Panel module without filter) 3.6 Viewing Angle : Over 160° 3.7 OSD language : English
4. Signal 4.1 AV & Graphic input 4.1.1 Composite signal : CVBS 4.1.2 Y,C Signal : S-Video 4.1.3 Component signal : Y, Pb/Cb, Pr/Cr, HDTV compatible 4.1.4 Graphic I/P : Analog: D-sub 15pin detachable cable Digital: DVI 4.1.5 PnP compatibility : DDC 1.0
4.1.6 I/P frequency : fH: 31.5kHz to 60kHz/fV: 56.25Hz to 75Hz (640x480 recommended)
Technical Specifications
PDP4206EM
CONTINUATION PAGE
NUMBER 4 OF 9 PAGES
4.2 Audio input Audio I/P(L/Rx5) : 1 for DVI / D-Sub 1 for Y/ Pb/Pr 1 for Y/ Cb/Cr
1 for Video 1 for S-Video
4.3 Audio output Audio O/P(L/Rx1) : 1 for Line out
4.4 Other function : PIP, 16:9, 4:3, Zoom 5. Environment 5.1 Operating environment 5.1.1 Temperature : 5ºC ~ 33°C 5.1.2 Relative humidity: 20% ~ 85%(non-condensing) 5.2 Storage and Transport 5.2.1 Temperature : -20°C to 60°C(-4º to 140°F) 5.2.2 Relative humidity: 5% to 95% 6. Panel Characteristics 6.1 Type : LG V6 6.2 Size : 42”, 1005mm(width)x597mm(height)x61mm(depth)±1 mm) 6.3 Aspect ratio : 16:9 6.4 Viewing angle : Over 160° 6.5 Resolution : 852x480 6.6 Weight : 14.8kg ±0.5 kg (Net) 6.7 Color : 16.77 million colors by combination of 8 bits R,G,B digital
6.8 Contrast : Average 60:1 (In a bright room with 150Lux at center) Typical 3000:1 (In a dark room 1/25 White Window
pattern at center). 6.9 Peak brightness : Typical 1000cd/ (1/25 White Window) 6.10 Color Coordinate Uniformity : Contrast; Brightness and Color control at normal
setting Test Pattern : Full white pattern Average of point A,B,C,D and E +/- 0.01
Technical Specifications
PDP4206EM
CONTINUATION PAGE
NUMBER 5 OF 9 PAGES
6.11 Color temperature : Contrast at center (50); Brightness center (50); Color temperature set at Natural x=0.285±0.02 y=0.293±0.02
6.12 Cell Defect Specifications Subject to Panel supplier specification as appends. 7. Front Panel Control Button 7.1 SEL. UP/Down Button : Push the key to selecting the item on OSD menu Volume Up/ Down Button : Push the key to increase the volume up or down. When selecting the adjusting item on OSD menu increase or decrease the data-bar.
Menu Button : Enter to the OSD menu. Input Select Button : Push the key to select the input signals source.
7.2 Stand by Button : Switch on main power, or switch off to enter power Saving modes. 7.3 Main Power Switch : Turn on or off the unit. 8. OSD Function 8.1 Audio : Adjust or Select Volume; Bass; Treble; Balance; SRS; BBE; AVC; Int./Ext. Speaker. 8.2 Picture : Adjust or Select Brightness; Contrast; Sharpness; Scaling (Picture changes According to Fill or One to One.; DNR; Video Format; More options for Y/Pb/Pr and VGA ( H. Position, V. Position Phase, Frequency) 8.3 OSD : Position; OSD H. Position; OSD V. Position; OSD Timeout; OSD Backgroud; Language. 8.4 Tools : Factory Reset; Source Scan; Blank Color; Turn Off Timer; Screen Saver; Saver Mode. 8.5 CC-V Chip : TV Channel Blocking; Movie Blocking; Change Blocking Password; Clear Password; CC Mode; CC Background.
Technical Specifications
PDP4294LV1
CONTINUATION PAGE
NUMBER 6 OF 9 PAGES
9. Agency Approvals Safety UL60950 Emissions FCC class B 10. Reliability
11.1 MTBF : 20,000 hours(Use moving picture signal at 25°C ambient) 11. Accessories : User manual x1, Remote control x1, Stand x1, Power cord x1, Battery x 2, Accessories box x 1.
Technical Specifications
PDP4206EM
CONTINUATION PAGE
NUMBER 7 OF 9 PAGES
12. Supportthe Signal Mode
The PDP can support the different from DVI or VGA Signal Mode in 24 kinds
NO. Resolution Horizontal Frequency
(KHz)
Vertical Frequency
(Hz)
Dot Clock Frequency
(MHz) 1# 640 x400 31.47 70.08 25.17 2# 640 x400 37.90 85.00 31.5 3 640 x480 31.50 60.00 25.18 4 640 x480 35.00 67.00 30.24 5 640 x480 37.50 75.00 31.50 6 640 x480 37.86 72.81 31.50 7# 640 x480 43.30 85.00 36.00 8 800 x600 35.16 56.25 36.00 9 800 x600 37.90 60.32 40.00 10 800 x600 46.90 75.00 49.50 11 800 x600 48.08 72.19 50.00 12 800 x600 53.70 85.00 56.25 13 832 x624 49.00 75.00 57.27 14 1024 x768 48.40 60.00 65.00 15 1024 x768 56.50 70.00 75.00 16 1024 x768 60.00 75.00 78.75 17 1024 x768 68.70 85.00 94.50 18* 1152x864 54.53 60.00 80.37 19 1152x864 67.52 75.02 108.03 20* 1152x864 63.86 70.02 94.51 21 1280x1024 63.37 60.01 111.51 22 1280 x960 75.02 75.02 126.00 23 1280 x960 60.02 60.02 108.04
24# 1280x720 44.96 59.95 74.19
Note: DVI could not support * of signal mode. VGA could not support # of signal mode. - Press “DISPLAY” button to confirm the input signal format. Note: Some data will be updated in five seconds if you change them.
Technical Specifications
PDP4206EM
CONTINUATION PAGE
NUMBER 8 OF 9 PAGES
13. Remote Function+
Sleep
Mute
YPbPr PC
Standby on/off
Number Buttons/ Channel up/ Channel down/ Return
PIP
EXIT Button
Video
BBE Wide
VOL +/-
Up/Down Left/Right
Button
SRS
ZOOM plus/minus
Display Freeze
Menu Left/Right
AUTO
Input
F.WHITE
Technical Specifications
PDP4206EM
CONTINUATION PAGE
NUMBER 9 OF 9 PAGES
PHYSICAL CHARACTERISTICS 14. Power Cord Length : 1.8m nominal Type : optional
15. Cabinet 15.1 Color : “Black” colour as defined by colour plaque reference number 15.2 Weight (with stand) Net weight : 84.5lbs (38.3kg) 15.3 Dimensions(with stand) Width : 40-7/8 inches (1040mm) Height : 27-1/4 inches (692mm) Depth : 11-1/4 inches
Product Specification of PDP Module
Color Plasma Display Panel852 X 480 pixels
Address Driver
Scan
Driv
er
Com
mon
sust
ain
driv
er
Display data, Driver timing
MemoryController
DriverTimingController
InputInterfaceController Vcc(+5V)
Va(55V~65V)
Vs(180V~190V)
Control Signal (Serial Interface)
APL Data
LVDS Input
Applied Voltage level is specified at the time when Full-White pattern is displayed on the panel.
Block Diagram
Block Diagram
Circuit Diagram
- Power supply board of PDP Module, DGP-420WXGA - Power supply board of PDP Module, USP490M-42LP - Main (Video) board - Audio/Tuner board - Keypad board - Remote control receiver board - External L/R Speakers board - Remote control board
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
18 1516 41513 237 17 911 1221 81920
D
HIC_MICOM
6
REVISION HISTORY
NO
1
변경전
변경후
일자/사유
2004/07/28 FEP30JPPH967C6
<D
<
m
1
R61212KF
R411
330F
R412
1K
F
C403 50V 0.68uF
R5041.8KF
C2250.1uF
R13233KF
PC
101
PC
-17K
1C
R214360RF
R5001W 10
D501
SUF30J
C111
0.1uF
R410
330F
R114
3K
TNR10114D 621K
R416
1K
F
0.001uFC204
C101
275VA
C 1
uF
R700
1W 10
R19956KF
R414
2K
F
D226LL4148
R2101W 10F
PC202
CN808
171825-8
1
2
3
4
5
6
7
8
R415
100F
PC-17K1CPC206
250V 0.47uFC126
R249
10KF
R17610KF
R137
10KF
L10123mH
R408
1K
F
1KFR261
D302US1M
Q108KTC3198Y
D503
D10L20U
CN033-176976-1
1
2
R1433W 470K
C116
0.0022uF
45.3KFR718
R126
75KF
R402 4.7KF
D103
LL4148
C105,106450V 330uF
L104CH108200S
D104US1M
PC102
D5001SF30SC6
IC300KA431AZ
R21710KF
IC501KIA278R12PI
1 2
3 4
Vin Vo
GN
D
ON
/OF
F
R2471.2K
R2291W 4.7F
Q202KRC103M
R301220F
C410
50V0.01uF
45.3KFR720
C701,702,704100V 330uF
J20
0RR508
C51635V 1000uF
C40050V 0.1uF
R531
35V 470uFC117
R5183.9KF
R115
1.5K
F
0.0047uFC212
Q107KTC3198Y
R149100KF
4.7KFR522
R403
1K
F
R609300KF
R19656KF
Q702KTC3207
CN804
171825-9
1
2
3
4
5
6
7
8
9
PC205
R5151.8KF
R189200KF
R5075W 2.7K
C1140.68uF
R4001KF
IC502KIA378R09PI
1 2
3 4
Vin Vo
GN
D
ON
/OF
F
KA7552AIC202
8
1
2
4
3
5
6
7
CS
RT
FB
GN
D
IS +
OUT
VC
C
CT
R155100KF
R1452W 240K
KA431AZIC500A
2KVR500
0.047uFC218
C2614.7uF
C1180.01uF
R2375W 0.1
C51035V 470uF
5KVR601
CRST4004MHZ
3
2
1 Xout
GN
DXin
C520
4.7KFR250
R3075W6.8
R216100KF
1W 100RR252
CN806
1-1123723-0
1
2
3
4
5
6
7
8
9
10
L5006*20 2.5uH
Q208KTA1281
R120160KF
C119
0.1uF
R51215KF
PC204
C406 50V 0.1uF
D105US1M
SW400
JSS 2209
R117180KF
C404 50V 0.1uF
R10410W 0.02
C10968PF
R2222.2M
R2271W 4.7
R423
1K
F
R248100KF
R233100KF
Q106
KSP2907
C600
1KV 220pF
0.22uFC205 D502
31GF6
CN809
171825-2
1
2
0.001uFC210
R5020
D200
LL4148
120KFR627
C51435V 47uF
SDT-SH-118DM
2W 100KR602
R5013.3KF
18KFR701
R404
1K
F
C3020.68uF
4.7uFC262
L10223mH
Q701KTC3207
R123330KF
10KR219
45.3KFR717
R13424KF
C1132.2uF
VA EER4042T206
R2212.2M
D300SB560
D500SF30SC6
R5051W 4R7
36KFR709
R124220KF
R127
75KF
R70620KF
D2111N5234B
R128
75KF
120KFR604
1KFR262
CN802
171825-4
1
2
3
4
45.3KFR721
R13333KF
270KFR606
R19356KF
R5161KF
R11324KF
C504,C555~C55710V 2200uF*4
T208PFC COIL 200uH
R610300KF
C407 50V 0.1uF
10KFR251
R1021W 390KJ
R154100KF
LED400GREEN
R3055W15
120KFR608
4.7KFR235
R5321W 2.7K
18KFR714
R70520KF
FSF10A60D600
R2242.2M
CN023-176976-1
1
2
R409
2K
F
470pFC208
R417
1K
F
PC206
D106US1M
C200630V 0.01uF
R405
1K
F
C102,103250V 0.001uF
C601
1KV 220pF
10uFC263
D1111N4148
R407
1K
F
Q210KRC103M
35V 47uFC220
KA7552AIC201
8
1
2
4
3
5
6
7
CS
RT
FB
GN
D
IS +
OUT
VC
C
CT
BYV26EGPD205
R112 3KF
C112330pF
C51135V 47uF
D3031N5245B
PC100PC-17K1C
C2270.001uF
C409 50V 0.1uF
C405 50V 0.1uF
35V 47uFC507
10V 2200uF*2C301,301A
RELAY1
R7072.7KF
R420
4.7K
F
LED401RED
LL4148D213
18KFR708
36KFR703
R70422KF
R11010KF
R1750
45.3KFR716
D208BYV26EGP
3.3KFR509
F101250VAC 8A
R148100KF
Q200KTA1281
R13610KF
18KFR615
R14410F
35V 47uFC120
R153100KF
R3065W6.8
C202 35V 47uF
35V 47uFC215
1uFC203
CN801
171825-7
1
2
3
4
5
6
7
R125
75KF
R406
1K
FC408 50V 0.1uF
SPW20N60C3*3Q102,Q103,Q109
R603
1W4R7
10KFR236
LL4148D204
C110470pF
PC
201
PC
-17K
1C
Q209SPW11N80C3
120KFR613
C222630V 0.1uF
C104630V 1uF
630V 0.047uFC206
R5191.5KF
Q206KTA1281
1W 47RR243
D102FEP30JP
R150100KF
C550~C55410V 2200uF*5
R526
2W 100KR620
IC400KIA7045AP
3
2
1 OUT
GN
DVCC
TNR10214D 621K
PC-17K1CPC202
R401 1KF
R21210KF
120KFR628
C2140.01uF
R1091W 4.7
PC100
R5132.7KF
IC200KA7552A
8
1
2
4
3
5
6
7
CS
RT
FB
GN
D
IS +
OUT
VC
C
CT
L103CH108200S
Q105KTA1281
250V 820uFC602
C2260.001uF
D1091N5236B
R2281W 4.7
Q203,204SPW11N80C3*2
1uFC216
R19856KF
PC-17K1CPC204
R600
1W4R7
R1462W 100
C5051KV 0.001uF
PC101
R5142KF
U101 UC3854N
1
2 345
6
7
8
9
10
11
1213 14 15
16
GN
D
PK
CAIS
MO
IA
VO
VR
RE
EN
VS
RS
SS
CT
VC
GT
R1426.8KF
C221630V 0.1uF
IC401HMS87C1304A
653 421 7 8 9 10 11 12131415161718192021222324
RD
0
VD
D
AN
6/R
A6
AN
6/R
A6
AN
5/R
A5
AN
4/R
A4
RD
1
AN
0/A
Vre
f/RB
0
BU
Z/R
B1
INT
0/R
B2
INT
1/R
B3
PW
M0/
CO
MP
0/R
B4
RD
2
RD
3
Xin
Xou
t
|RE
SE
T
Vss
RC
0
RC
1
RA
0/E
C0
RA
1/A
N1
RA
2/A
N2
RA
3/A
N3 C
411
50V0.01uF
Q300FQP17N40
STBY EE1927T100
D2121N5234B
C2010.01uF
18KFR710
R118180KF
FSF10A60D700
R135
10K
F
FSF10A60D601
Q104KTC3209
R418
1K
F
R1061W 4.7
L301
27uH
PC201
D202BYV26EGP
35V 47uFC123
11KFR711
50V 1
0uF
C115
CN013-176976-2
12
R111100F
130KFR607
18KFR719
R1035W 20
C700
1KV 100pF
R19556KF
45.3KFR715
R2304.7KF
T204,205VS EER4042
U1005M0280R-YDTU
12 3
4
GN
DD
RA
IN
VC
CF
B
R3021.02KF
2W 240KR226
0.001uFC211
R190200KF
5KVR700
R140
7.5KF
R1414.7KF
R5105W 1K
SELCABLE
35V 470uFC128
470FR520
C40150V 0.1uF
R121160KF
R13133KF
Q207KRC103M
D107US1M
R422
10K
F
R1085W 15
R130240KF
Q201SPW11N80C3
1uFC530
56KFR525
C108680pF
33KFR702
1uFC209
PC205PC-17K1C
R152100KF
R51115KF
D206LL4148
C30450V 4.7uF
MULTI EER4042T207
0.01uFC219
BD101D25XB60
R119180KF
R611300KF
2.4KFR260
D301US1M
R1561KF
C5001KV0.001uF
50V 220uFC506
4.7KFR218
R2315W 0.05
R303
1KF
R12218KF
R421
10K
F
R2465W 0.2
R2232.2M
CN803
1-171825-2
1
2
3
4
5
6
7
8
9
10
11
12
C519
C213630V 0.01uF
R11610KF
R2251M
R1071W 4.7
LL4148D203
LL4148D209
C121
630V 0
.01uF
R151100KF
R503
1KF
R2321K
CN805
1-1123723-4
1
3
4
2
0.001uFC217
CN807
1-1123723-8
1
2
3
4
5
6
7
8
18KFR712
R129150KF PC-17K1C
PC102
R24510KF
R2532W 240K
D108
1N
5236B
1/4W 100RR220
IC500KA317
1 2
3
Adj Output
Inpu
t
R19256KF
R2092W 240K
VS_ON
+5V D
ET
9VSC
+12V D
ET
5VCTRL
60VA
RYC
ACD
5VSC
PFC +
RLY_ON
RLY O
N
SB5V
AC
D O
UT
VI
5VCTRL
190VS 5VCTRL
AC
DET
VI
60VA
9VSC
190VS
+5VSTB
Y
VS D
ET
24V/30V
+30V D
ET
+9V D
ET
VS O
N
RY O
N/O
FF
RYC
12VSC
VA
DET
VA VCC
PFC
ON
/O
FF
5VSC
5VD
PFC+
MU
LTI O
N/O
FF
60VA
PFC+
VA DET
5VD
OU
T
GND
MULTI VCC
PFC +
+12V /1.0A
GND
+9V DET
+12V DET
9VSC
PFC +
VA VCC
VS DET
190VS
190VS
GND
VA
,VS O
N/O
FF
PFC VCC
VA ON/OFF
60VA
GND
GN
D
GND
GN
D
방전
CTL
VA
AC-1
PFC+
PFC VCC
AC DET
PFC GND
+5VSTBY
PFC ON/OFF
방전 CTL
GND
VS
+5V DET
5VCTRL
+30V/1.0A (+24V/1.25A)
5VSC
GND
MULTI ON/OFF
+5VCTRL
+30V DET
DGP-420WXGA
USP490M-42LP
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
TOP c
PW171-LGPDP
B
1 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
POWER
11_POWER
VCP3230
05_VCP3230
VVINT VUV[7:0]CBRESETnYSDA
VVHSVY[7:0]VVCLK
SCLVVVSCR
VFIELDMUTE
POWER_ONMUTE1
IR
STBLED
NV320
06_NV320
VG[7:0]VB[7:0]VR[7:0]
SDASCLVVHSRESETnVVCLKNDSP_EN
VCLKVVSVHS
VPENVY[7:0]VUV[7:0]VVVS
MEMORY
07_MEMORY
SDASCLROMWEnROMOEnVPPEND[15:0]A[19:1]
PW171
08_PW171
DGE[7:0]DBE[7:0]DRO[7:0]DGO[7:0]DRE[7:0]DBO[7:0]
DCLKGBLKSPLGCOASTROMWEn
D[15:0]
ROMOEnTXD
SDAA[19:0]GFBKCS1nVPPENRDnNMIVR[7:0]VCLKVG[7:0]VB[7:0]GHSGCLKGRE[7:0]GBO[7:0]GBE[7:0]GGO[7:0]GRO[7:0]GVSGGE[7:0]MCKEXTRXDIRRCVR1RESETDCKEXTVPENVVSVFIELDGPENICSCLKICSSTDICSSTMICSDATLED-RLED-GNDSP_ENDTXONVGASEL
DVSDENBDENGDENR
DHS
GAFEOEGDFEOEVVINTVHSMUTESLEEP1PIO3CPUGOPDPGO
SCL
RESET-2PDWNIRQ
TMDS
09_TMDS
DBO[7:0]DHSDENGDENRDGE[7:0]DRE[7:0]DGO[7:0]DRO[7:0]DCLKDVSDENBDBE[7:0]
MISC
10_MISC
LED-GICSSTM
DCKEXT
ICSCLKICSSTDLED-R
MCKEXT
ICSDAT
RXD
TXD
RESETRESETn
NMI
RDnD[7:0]CS1n
POWER_ONIRRCVR1
STBLED
LVDS
12_LVDS
DENGDCLKDVSDHSDTXONRESET-2SCLSDACPUGOPDPGOPDWNIRQDGE[7:0]DRE[7:0]DBE[7:0]
INPUT
02_INPUT
GBAINGGAINRXCmRX0m
GHSYNCRX1mRXCp
HDCBINHDYINRX1pRX2p
GRAINY
RX0pRX2m
GVSYNCCB
HDCRINCR
AFE
04_AFE
HDCBIN GBE[7:0]GRE[7:0]HDYIN
GAFEOEVGASELGVSYNCGCOAST
GHS
HDCRINGRAIN
GCLK
SCLGBAIN
GFBK
GBLKSPLGGAINSDAGHSYNC
GGE[7:0]GVS
DVI
03_DVI
RXCmRX0m
GRE[7:0]GPEN
RX1p GBE[7:0]RX1mRX0p
GVSGBO[7:0]
GDFEOERX2m
GFBK
RX2pGHS
GGE[7:0]GCLK
GRO[7:0]RXCp
GGO[7:0]
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
Drawn by: Checked by: Approved by:
ADR5
GGE1ADG2
ADR4
ADSOG
GGIN
ADR2ADR1
GBE2
ADR6
GBIN
ADR0
GMRED
GRE3
GBVSY
ADVS
ADB5
GRIN
GRE5
ADG7
ADB1
ADG0
GGE7
GGE0
ADG4
GGE2
ADB0
GBHSY
GRE4
ADB2
GMIDV ADHS
GGE3
ADB6
GRE0
ADG1
GMBLU
ADB3
GFLT1
GBE4
GRE2
GGE5
ADR3
ADG6
GBE3
GBE6ADB7
GBE0
ADR7
GSOGIN
GFILT
ADSOGR
ADCK
GBE1
GRE7
ADG5
GRE6
GBE7
GRE1
GBE5
GGE4
GGE6
GVREF
ADB4
GMGRN
ADG3
VCCAVDD AVDD
V33V33
AVDD V33 PVDD
AVDD
V33
VCC
AVDD AVDDAVDD
V33 V33
AVDD AVDD
V33
VCC
V33
AVDD
PVDD
PVDD
PVDD
V33
VCCAVDD
PVDD
AVDD
V33
RP1747R
C45
0.1uF
C6247nF
TP9
C44
0.1uF
R16
3.3K
U5LM2937_SOT223
1
2
3
4
VI
GN
D
VO
TA
B
C641nF
C39
0.1uF
U9 PI5V330
25
1114
36
1013 8
1615
1
47912
A1A2A3A4
B1B2B3B4 GND
VCCOEA/B
Y1Y2Y3Y4
C37
0.1uF
C61
0.1uF
C40
0.1uF
C6347nF
RP1947R
U6LM2937_SOT223
1
2
3
4
VI
GN
D
VO
TA
B
C43
0.1uF
C41
0.1uF
C34
0.1uF
C66
0.1uF
C47
0.1uF
C50
0.1uF
C48
0.1uF
RP1647R
RP1547R
C56
0.1uF
U8A
74LVC126A
1
2 3
714
C35
0.1uF C49
47uF
C6547nF
C54
0.1uF
U8D
74LVC126A
13
12 11
C57
0.1uF
C51
0.1uF
C55
0.1uF
TP8
U7
AD9883A_1401918171615141312
7776757473727170
98765432
5837
67
646566
575655
30
29
31
38
54
48
43
33
1 10 20 21 24 25 28 32 36 40
26 27 39 42 45 46 51 52 59 62 11 22 23 69 78 79 34 35
41 60 61 63 68 8044 47 50 53
49
BLUE0BLUE1BLUE2BLUE3BLUE4BLUE5BLUE6BLUE7
RED0RED1RED2RED3RED4RED5RED6RED7
GREEN0GREEN1GREEN2GREEN3GREEN4GREEN5GREEN6GREEN7
REFBYPMIDSCV
DATACK
VSOUTSOGOUT
HSOUT
SDASCLA0
HSYNC
COAST
VSYNC
CLAMP
RAIN
GAIN
BAIN
FILT
GN
D1
GN
D2
GN
D3
GN
D4
GN
D5
GN
D6
GN
D7
GN
D8
GN
D9
GN
D10
AV
D1
AV
D2
AV
D3
AV
D4
AV
D5
AV
D6
AV
D7
AV
D8
AV
D9
AV
D10
VD
D1
VD
D2
VD
D3
VD
D4
VD
D5
VD
D6
PV
D1
PV
D2
GN
D11
GN
D16
GN
D17
GN
D18
GN
D19
GN
D20
GN
D12
GN
D13
GN
D14
GN
D15
SOGIN
TP7
C42
0.1uF
U8B
74LVC126A
4
5 6
C46
47uF
C68
0.1uF
RP1447R
C38
0.1uF
C58
47uF
RP2047R
C53
0.1uF
RP1847R
C67
0.1uF
C59
39nF
C52
0.1uF
U8C
74LVC126A
10
9 8
C60
3.9nF
C36
0.1uF
GGE[7:0]
GGAIN
GVSYNC
GAFEOE
GCLK
GCOASTGBLKSPL
GBAIN
GHSYNC
VGASEL
HDCBIN
GRAIN
HDYIN
GVS
GFBK
GHS
GBE[7:0]
SDASCL
HDCRIN
GRE[7:0]
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
DVI INPUT C
PW171-LGPDP
B
3 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
GGE2
GRE2
GRO5
GGE4
GRO2GRO1
SIGE0
SIGE2
SIGE7
GBO5
SIRO0
GGO3
SIBO0
GBO7
GGO7
SIRES
GBE4
SIRO1
SIGO4
SIVS
SIRE2
SIGE4
GBE7
GGE5
GGE3
SIBE4
SIRE3
SIRE1
SIRE4
GGE1
SIBE2SIBE3
GGE0
GRE1
SIRE7
SIBO3
SIRO4
GBE2
GRO4
SIGO0
GGO4
SIBO4
GGE6
SIRO7
SIGO6
SIBO2
SISCDT
SIGE6
SIBE5
SIGE3
SIBO5
GRE6
GBO0
GBO3
GRE7
SIBE0
GRO3
GBE0
GBO6
GRO7
GRE5
SIRE0
SIGE5
GBE5
SIRE5
GRO6
GGO6
SIRE6
SIBO7
SIGO1
SIGO5
GBE1
GRO0
GRE3
SIBE6
GGO0
SIGE1
GRE4
SIBO6
GBO2
SIGO2
SIRO3
SIBE1
GBO4
GGO2
SIBE7
SIRO6
SIDE
GBO1
SICLK
GGE7
SIGO3
GBE3
SIHS
GBE6
SIBO1
GGO1
SIRO2
GGO5
SIRO5
SIGO7
GRE0
OVCC
V33T
AVCC
PVCC VCC
AVCC
AVCCAVCC
CVCC
V33T
OVCC
PVCC
OVCC
AVCC
V33T
OVCCV33T
V33T
AVCC AVCC
OVCC
PVCC
CVCC
OVCC
CVCC
OVCC
OVCC
CVCCCVCC
C22
0.1uF
RP10 47R
RP4 47R
L17FB_420_OHM_200MA
TP2
C33
0.1uF
C20
0.1uF
C32
0.1uF
RP2 47R
C15
0.1uF
C29
10uF
C21
0.1uF
TP6
C18
0.1uF
L18FB_420_OHM_200MA
U3LM2937_SOT223
1
2
3
4
VI
GN
D
VO
TA
B
C14
0.1uF
RP12 47R
L15FB_420_OHM_200MA
C16
47uF
RP11 47R
R15
510
TP5
RP5 47R
RP3 47R
RP8 47R
C23
10uF
C19
0.1uF
L16FB_420_OHM_200MA
C27
10uF
TP1
TP4
RP13 47R
C26
0.1uF
C17
10uF
C25
0.1uF
C30
0.1uF
TP3
RP9 47R
C31
0.1uF
C28
0.1uF
RP7 47R
RP1 47R
U4
SII161
9091
8586
8081
9394
96
100417392
8
1011121314151617
49505152535455
44464748
404142
19 28 45 58 76 5 39 68 98 79 83 87 89 92
18 29 43 57 78 6 38 67 97 82 84 88 95
20212223242526273031323334353637
5659606162636465666970717273747577
99
RX0pRX0m
RX1pRX1m
RX2pRX2m
RXCpRXCm
EXT_RES
OCK_INVPIXSDFOSTAG_OUTSTPDOPD
SCDT
QE0QE1QE2QE3QE4QE5QE6QE7
QO0QO1QO2QO3QO4QO5QO6
ODCKDE
VSYNCHSYNC
CTL1CTL2CTL3O
GN
D1
OG
ND
2O
GN
D3
OG
ND
4O
GN
D5
GN
D1
GN
D2
GN
D3
PG
ND
AG
ND
1A
GN
D2
AG
ND
3A
GN
D4
AG
ND
5
OV
CC
1O
VC
C2
OV
CC
3O
VC
C4
OV
CC
5
VC
C1
VC
C2
VC
C3
PV
CC
AV
CC
1A
VC
C2
AV
CC
3A
VC
C4
QE8QE9
QE10QE11QE12QE13QE14QE15QE16QE17QE18QE19QE20QE21QE22QE23
QO7QO8QO9
QO10QO11QO12QO13QO14QO15QO16QO17QO18QO19QO20QO21QO22QO23
RSVD
RP6 47RC24
0.1uF
GRO[7:0]
RX1pRX1m
GCLKGPEN
GHS
GFBK
GBE[7:0]
GGO[7:0]
GGE[7:0]
RX2p
RXCm
GRE[7:0]
RX2m
GDFEOE
GVS
RXCp GBO[7:0]
RX0pRX0m
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
FLASH C
PW171-LGPDP
B
7 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
IRPnA11
A6
A4
A16
A9
A18
A12
D10
A3D3
D7
D8
D5
D11
IA21
D12
A8
D1D0
A3
D11
D4
A13A15
D5
A15
FCEn
D13
D3
A10 VP1
A19
D1
IA20A19A17
A7
D15
A9
D0
A12
VPP
VP2
D14
VP3
A6
A13
A7
D13
A5
A14
D6
D10
VPPON
D15
D6
D8
D7
D12
A8
A2
A11
D14
D9
A18
A1
A14
D2
A2
A5
A1
ICEn
D9
A4
A10
A17
FWPn
A16
D2
D4
V33
V33
V33 V33
V33
VCC
V33
VCC
V33
V33
U16
Flash_8M
37
13
4627
29
30
31
32
33
34
35
36
38
39
40
41
42
43
44
45
12345678
17
1819202122232425
48
262811121447
16
VCC
VPP
GND1GND2
D1
D9
D2
D10
D3
D11
D4
D12
D5
D13
D6
D14
D7
D15
D8
D16
A15A14A13A12A11A10A9A8
A17
A7A6A5A4A3A2A1A0
A16
CEOEWERPWPBYTE
A18
R73 3.3K
JP1
HDR_2X2
1 23 4
Q53904
1
23
R74 3.3K
C169
0.1uF
R75 3.3K
C168
0.1uFR68 10K
R67
1K
JP2
HDR_2X2
1 23 4
R72 3.3K
Q43906
1
3 2
R69
3.3K
R71
3.3K
C167
22uF
JP3
HDR_30X2
1 23 45 67 89 1011 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 3233 3435 3637 3839 4041 4243 4445 4647 4849 5051 5253 5455 5657 5859 60
U17
24C16
56 8
4
123
7
SDASCL VCC
GND
NC0NC1NC2
WP
R70
3.3K
ROMOEn
ROMOEn
SCL
ROMWEn
SDA
ROMWEn
D[15:0]
A[19:1]
VPPEN
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
INPUT C
PW171-LGPDP
Custom
2 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
CR
GGREENF
GVCK
CB
HDCB
GGREEN
HDYF
HDCBF
HDCR
GDC5V
GREDF
GBLUEF
G5V
GSCLGSDA
CSCL
CVCK
GBLUE
HDCRF
Y
CSDA
HDY
GRED
GVCC
GVCC1
GVCC1
GVCC
VCC
GVCC1
AVDD
GVCC1
VCC
AVDD
GVCC
GVCC1
GVCC
AVDD
GVCC1
GVCC
GVCC1 AVDD
GVCC
VCC
GVCC
GVCC1
AVDD
GVCC1
GVCC1
GVCC1
AVDD
GVCC
GVCC1
VCC
D13
BAV70L
1
23
C12
47uF_NS
D8
BA
V99
L1
3
2
L2 FB_40_OHM_500MA
R14
2K
L10 FB_40_OHM_500MA
C10
47uF_NS
L7 FB_40_OHM_500MA
C2
12pF
C11
0.1uF
L3 FB_40_OHM_500MA
D10
BA
V99
L1
3
2
C4
0.1uF
R7
3.3K
C9
12pF
U1
24LC21A
123
4
56
78
NC1NC2NC3
GND
SDASCL
VCLKVCC
R1
75
L14NS
U2
24LC21A
123
4
56
78
NC1NC2NC3
GND
SDASCL
VCLKVCC
R12
75
J1
YUV
1
2
34
5
67
8
9
J15DB15HD_V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1617
D2
BA
V99
L1
3
2
R5
3.3K
C3
12pF
C8
12pF
L9 FB_40_OHM_500MA
C7
12pF
J2
DVI_V
123456789101112131415161718192021222324
25
26
C1C2C3C4C5C6
27
28
DATA2-DATA2+
DATA2/4_SHLDDATA4-DATA4+
DDC_CLKDDC_DATA
A_VSYNCDATA1-DATA1+
DATA1/3_SHLDDATA3-DATA3+
+5VGND
H_PLUG_DETDATA0-DATA0+
DATA0/5_SHLDDATA5-DATA5+
CLK_SHLDCLK+CLK-
SHELL1
SHELL2
A_REDA_GREEN
A_BLUEA_HSYNC
A_GND1A_GND2
NC1
NC2
L12 FB_40_OHM_500MA
R2
75
D11
BA
V99
L1
3
2
R4
3.3K
D12
BA
V99
L1
3
2
D14
BAV70L
1
23
R3
75
L5 FB_40_OHM_500MA
D3
BA
V99
L1
3
2
L4 FB_40_OHM_500MA
R13
2K
D5
BA
V99
L1
3
2
R8
3.3K
D9
BA
V99
L1
3
2
R9
3.3K
D4
BA
V99
L1
3
2
R11
75
R6
3.3K
D7
BA
V99
L1
3
2
L13
NS C13
0.1uF
L1 FB_40_OHM_500MA
L8 FB_40_OHM_500MA
L11 FB_40_OHM_500MA
L6 FB_40_OHM_500MA
R10
75
C1
12pF
D6
BA
V99
L1
3
2
D1
BA
V99
L1
3
2
C5
0.1uF
GBAIN
GGAIN
RXCm
RX0m
GHSYNC
RX1m
RXCp
HDCBIN
HDYIN
RX1p
RX2p
GRAIN
Y
RX0p
RX2m
GVSYNC
CB
HDCRIN
CR
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
LVDS OUTPUT C
PW171-LGPDP
B
12 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
ARE4
ARE5
DRE4
AGE6
DBE1
AGE5
DBE4
ABE6
3WSCL
ABE7
ARE6
ABE6
DGE0
ARE5
DGE6
AGE6
DRE3
AGE7
DGE7
DBE3
AGE6
ABE7
TXE1p
3WSLE
ARE6
DGE7
ARE7
DGE3
SDA
ABE7
DGE0
DBE0
ARE6
AGE7
ABE0
DBE5
AGE7
ABE0
DRE0ARE7
AGE0
DBE4
ABE2
DGE5
DRE4
ARE7
AGE0
ABE1
DGE5
ARE0
DGE4
ABE0
ABE1DBE2
ARE0
AGE1
TXE2m
ABE3
PDWN
AGE0
AGE1DGE2
ABE2
DBE7
ARE1
DRE7
TXE0m
ABE1
ARE0
DRE5
ARE1
AGE2
DRE2
ABE4
DBE3
TXE3m
AGE1
TXECKp
AGE2
DBE7
ABE3
ARE2DRE3
ABE2
DRE7
ARE1
DGE1
ARE2
DGE2AGE3
ABE5
DBE0
AGE2
DRE6
AGE3
DGE3
TXE0p
ABE4
ARE3
DBE2
ABE3
DGE4
TXE2p
ARE2
ARE3
AGE4
DRE5
DRE1
AGE3 TXE1m
AGE4
DRE1
ABE5
ARE4
DRE6
ABE4
DGE6
ARE3
DRE2SCL
ARE4
DBE1
AGE5
DGE1
DRE0
AGE4
AGE5
3WSDA
DBE6
TXE3p
ABE6
ARE5
ABE5
DBE5
DBE6
TXECKm
V33V33
V33V33V33V33
R1430
RP5147R
RP5247R
R1440
C275
0.1uF
RP6047R
J14
JEA31
12345678910111213141516171819202122232425262728293031
RP5347R
RP6447R
R1400
C277
0.1uFR1390
RP6247R
U31
DS90C383A
5152545556
2
3
467
810
111214
15
1618
1920222324
25
272830
50
47
45
41
37
39
48
46
42
38
40
31
3217
1 9 26 3444
5 13 21 29 53 33 3536 43 49
TXIN0TXIN1TXIN2TXIN3TXIN4
TXIN5
TXIN6
TXIN7TXIN8TXIN9
TXIN10TXIN11
TXIN12TXIN13TXIN14
TXIN15
TXIN16TXIN17
TXIN18TXIN19TXIN20TXIN21TXIN22
TXIN23
TXIN24TXIN25TXIN26
TXIN27
TXOUT0
TXOUT1
TXOUT2
TXOUT3
TXCOUT
TXOUT0
TXOUT1
TXOUT2
TXOUT3
TXCOUT
CLKIN
PWRDNR_F
VC
C1
VC
C2
VC
C3
PV
CC
OV
CC
GN
D1
GN
D2
GN
D3
GN
D4
GN
D5
PG
ND
1P
GN
D2
OG
ND
1O
GN
D2
OG
ND
3
RP6147R
C276
0.1uF
RP5547R
J13
CON20A
135791113151719
2468
101214161820
RP6547R
RP5447R
C274
0.1uF
RP5047R
R1410
RP6347R
C273
0.1uF
R1420
DHS
DGE[7:0]
DVS
3WSLE
DTXON
DGE[7:0]
SCL
DBE[7:0]
DRE[7:0]
PDWN
DBE[7:0]
3WSCL
DRE[7:0]
DCLK
DENG
SDA
3WSDA
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
Remove for Production
CLOCK GENERATOR
LED
FROM PDP
MISC C
PW171-LGPDP
B
10 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
D6
D0
TLCCT
POWER_ON(MUNE)TV_AV
D7
IX2
RDCK
MC2P
D2D3
STBLED
MRXD
D1
VOL_UP
NMI1
MC2M
D4
MVPMC1M
D5
RRXD
ICSREF
MVM
P_UP
VOL_DOWN
RMCK
RSTINn
MC1P
P_DOWN
IR
MTXD
IX1
MUNE
IR
STBLED
V33
V33
V33
V33
VCC
V33V33
V33
V33
V33
+5VIN
V33
V33
V33
V33
VCC
+5V
V33
V33
V33
V33
V33
+5V
+5VIN
V33
VCC
V33
V33
+5V
+5VIN
+5V
C231
0.1uF
J9
PH-3A
123
R10
51K
C235
0.1uF
R9947
C239
0.1uF
U26 74LVC541AD
23456789
10
20191
1817161514131211
I0I1I2I3I4I5I6I7
GND
VCCOE2OE1
O0O1O2O3O4O5O6O7
R107
4.7K
C236
0.1uF
R389
1K
R108
20K
C238
0.1uF
R118 NS
C237
0.1uF
DCKEXT1
U25
MAX232A
15
16123
45
6
7
89
1011
12 13
14
GND
VCCC1PVPC1M
C2PC2M
VM
TOUT2
RIN2ROUT2
TIN2TIN1
ROUT1 RIN1
T1OUT
U24
TLC7733
4
5
2
8
6
1
3
7
GND
RESET
RESIN
VDD
RESET
CONTROL
CT
SENSE
R11010K
R11110K
R11210K
R11310K
R11410K
R11510K
MCKEXT1
Y3
XTAL14.31818
R11610K
R10910K
C2430.1uF
J8
PH-6A
123456
C2414.7uF
SW1SW_MOM_4P
1 4
2 3
C2440.1uF
SW2SW_MOM_4P
1 4
2 3
C2450.1uF
C230
0.1uF
J16
CON5
12345
C2460.1uF
U21
ICS307
116
11812
13 3
5
69
X1X2
CLK1SCLKDATA
OE VDD
GND
CLK2STROBE D19
LED RED
C2470.1uF
R106 1K
Q6
3906
1
32
C2480.1uF
JP5HDR_4X1
1234
C2490.1uF
R98510
C2424.7uF
J7
DB9_V
594837261
1011
C232
0.1uF
R10247
U23
ICS307
116
11812
13 3
5
69
X1X2
CLK1SCLKDATA
OE VDD
GND
CLK2STROBE
R104200
C233
0.1uF
C240
0.1uF
J10
PH-14A
1234567891011121314
C234
0.1uF
R103
10K
RESETn
ICSSTD
IRRCVR1
RESET
ICSCLK
CS1n
D[7:0]
DCKEXT
TXD
RDn
RXD
ICSSTM
POWER_ON
STBLED
NMI
ICSDATMCKEXT
IR
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
DEINTERLACE C
PW171-LGPDP
C
6 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
VUV6
MD19
NV
320X
O
GRN_Y3
RED_Cr6
MA7
BLU_Cb3
MA10MA10
BLU_Cb1
MD2
VG7
MD18
BLU_Cb0
VUV1
MD7
VR1
CLK
_M
MD
7
RED_Cr5
MD4
VY6
MWE-
VY3
MD10
BLU_Cb6
CLK_M
GRN_Y7
MD
6
MD20
MD15
MD
17
MA2
MD13
VR5
RED_Cr7
BLU_Cb7
GRN_Y1
GRN_Y5
MD3
MA
3
VY2 GRN_Y0
MD26
MA7
VB[7:0]
MA
8
MD16
MD
3
VCC320A
VG5
MA
10
COMP320
VB1
VUV3
MD11
VR[7:0]
MD
15
VUV5
MD31
RED_Cr2
MW
E-
MCS-
MD0
MD
5
MD
14
MA
2VB5
MD
8
MD23
MD28
VR7
CLK_M
VG6
BLU_Cb2
CAS-
MA
6
VUV0
RED_Cr3
MA6
VUV2
MD30
VR2
MD
12
CA
S-
VR0
REF320
VUV7
MD
11
MD
1
MA1
MD
4
DQM1
VR4
VY5
MA2
MA8
VG0
MA3
VG[7:0]
DQ
M1
VB4
MD
29
MA4
MA6
MA1
NV
320X
I
VY0
MA
9
RAS-
MD
31
MD
2
BLU_Cb4
MA9
VUV4
VB3
MA
4
CAS-
MD17
VY1
MD29
VB7
MD
26
MA0
MD
24
RA
S-
MD
21
MA3
MD14
MD21
MD
30
MC
S-
MA8
MWE-
MD
22
DQ
M0
VY7
VB2
MA
5
GRN_Y6
MD8
GRN_Y4
MD27
MD1
MD
20
MD
18
MA
7
MD
28
MD12
MD
0
MA5
VG1
MA
1
MA5
MD
19
MCS-
GRN_Y2
RSET320
MD6
VR3
VG2
MD22
MD
27
DQM0
MD
13
RED_Cr4
MD
16
MA
0
MD
23
LLC320
MD9 MD25
VB0
RAS-
MA4
VY4
RED_Cr1
VCC320P
MD
9
MA0
MD24
BLU_Cb5
MD5
VG3VG4
MD
25
VR6
RED_Cr0
MD
10
MA9
VB6
V33N
V33N
V33N
V33N
V33N
V33N
V33N
V33N
VCC
V33N
V33NVCC
V33N
V33N
V33N
V33N
RP29 47R
182345
67
C1590.1uFX7R0603
C1380.1uFX7R0603
TPVS
L2810uH
R65
0
C1580.1uFX7R0603
RP32 47R1 8234 5
67
RP26 47R
182345
67
+ C154
10uF
+ C148
22uF
C124
0.1uF
C1130.1uFX7R0603
C1400.1uF
U14LM2937_TO263
1
2
3VI
GN
D
VO
C1620.1uFX7R0603
TPHS
TPVCK
+ C156
10uF
C1300.1uFX7R0603
C1170.1uFX7R0603
C1450.1uF
RP27 47R
182345
67
C1230.1uF
RP33 47R
1 8234 5
67
C1470.1uF
L2710uH
C1550.1uFX7R0603
U15
NV320
171172173174175176178179
180181183184185186187188
189190191192193194195196
159163164165
197198199200201202203
2427
167168169
204
9 8 6 5 4 2 1 208
20 18 17 16 14 13 12 10 147
146
145
143
142
141
140
138
158
156
155
154
152
151
150
149
124
123
122
120
33 32 30 29 125
26 127
21 137
136
135
129
128
22
118119116115
114
3435
113111110
7267666059524947
9190888786848281
10610510310099979695
3741383942109
687775
437476
565758
636465
697071
3 11 19 31 40 48 61 83 93 104
112
121
130
144
153
162
170
28 85 131
182
7 15 23 36 44 53 79 89 98 108
117
126
139
148
157
166
207
25 78 134
177
101
205
161
102
206
160
4645
8073
9492
107
5150
132
133
Y0Y1Y2Y3Y4Y5Y6Y7
U0U1U2U3U4U5U6U7
V0V1V2V3V4V5V6V7
DVDLLCDVDBDVDHSDVDVS
ODDVSHSHREFCREFLLCHRCLLAD2HRACLVHREFOLLA
RESET
DQ
0D
Q1
DQ
2D
Q3
DQ
4D
Q5
DQ
6D
Q7
DQ
8D
Q9
DQ
10D
Q11
DQ
12D
Q13
DQ
14D
Q15
DQ
16D
Q17
DQ
18D
Q19
DQ
20D
Q21
DQ
22D
Q23
DQ
24D
Q25
DQ
26D
Q27
DQ
28D
Q29
DQ
30D
Q31 A
0A
1A
2A
3A
4A
5A
6A
7A
8A
9A
10
DQ
M0
DQ
M1
WE
CA
SR
AS
CS
CLK
CSA0CSA1I2C3WSCS
RFLOCK
SDASCL
APLLFOEQP60
YQ0YQ1YQ2YQ3YQ4YQ5YQ6YQ7
UQ0UQ1UQ2UQ3UQ4UQ5UQ6UQ7
VQ0VQ1VQ2VQ3VQ4VQ5VQ6VQ7
PCLKVSQHSQHVQVBQDVQ
COMPDAC-VCCDAC-GND
RSETVREFOUT
VREFIN
YARED-VDDRED-GND
BYAGRN-VDDGRN-GND
RYABLU-VDDBLU-GND
VC
CIO
_1V
CC
IO_2
VC
CIO
_3V
CC
IO_4
VC
CIO
_5V
CC
IO_6
VC
CIO
_7V
CC
IO_8
VC
CIO
_9V
CC
IO_1
0V
CC
IO_1
1V
CC
IO_1
2V
CC
IO_1
3V
CC
IO_1
4V
CC
IO_1
5V
CC
IO_1
6V
CC
IO_1
7
VC
C_C
OR
E_1
VC
C_C
OR
E_2
VC
C_C
OR
E_3
VC
C_C
OR
E_4
GN
D1
GN
D2
GN
D3
GN
D4
GN
D5
GN
D6
GN
D7
GN
D8
GN
D9
GN
D10
GN
D11
GN
D12
GN
D13
GN
D14
GN
D15
GN
D16
GN
D17
GN
D_C
OR
E1
GN
D_C
OR
E2
GN
D_C
OR
E3
GN
D_C
OR
E4
GN
D_P
LL1
GN
D_P
LL2
GN
D_P
LL3
VC
C_P
LL1
VC
C_P
LL2
VC
C_P
LL3
YQ8YQ9
UQ8UQ9
VQ8VQ9
TEST
ADVDDADGND
XI
XO
C1260.1uF
+ C152
1uF
C1280.1uF
C1150.1uFX7R0603
+ C149
22uF
RP30 47R
182345
67
U13
HY57V161610D-7
35
14
2356
26
18
2122232427282930313220
34
151617
25
7133844 4
104147
8911123940424345464849
19
36
150
3337
CLK
LDQM
DQ0DQ1DQ2DQ3
VSS
CS
A0A1A2A3A4A5A6A7A8A9A10
CKE
WECASRAS
VDD
VDDQVDDQVDDQVDDQ VSSQ
VSSQVSSQVSSQ
DQ4DQ5DQ6DQ7DQ8DQ9
DQ10DQ11DQ12DQ13DQ14DQ15
BA
UDQM
VDDVSS
NCNC
C1370.1uFX7R0603
C1430.1uF
Y110.000MHZ
HC-49/SD
C1160.1uFX7R0603
R66 2M
+ C151
22uF
RP31 47R182345
67
C1530.1uFX7R0603
+ C161
10uF
R62 0
C1350.1uFX7R0603
C1220.1uFX7R0603
C1640.1uFX7R0603
C1140.1uFX7R0603
C1340.1uFX7R0603
C1410.1uF
C1320.1uFX7R0603
C1180.1uFX7R0603
C1190.1uFX7R0603
C1460.1uF
C1310.1uFX7R0603
U12
HY57V161610D-7
35
14
2356
26
18
2122232427282930313220
34
151617
25
7133844 4
104147
8911123940424345464849
19
36
150
3337
CLK
LDQM
DQ0DQ1DQ2DQ3
VSS
CS
A0A1A2A3A4A5A6A7A8A9A10
CKE
WECASRAS
VDD
VDDQVDDQVDDQVDDQ VSSQ
VSSQVSSQVSSQ
DQ4DQ5DQ6DQ7DQ8DQ9
DQ10DQ11DQ12DQ13DQ14DQ15
BA
UDQM
VDDVSS
NCNC
C165
22pF
C1200.1uFX7R0603
C1250.1uF
C1390.1uFX7R0603
C1630.1uFX7R0603
C1290.1uF
C1600.1uFX7R0603
C1330.1uFX7R0603
C1360.1uFX7R0603
R64
100NO STUFF
C150
0.1uF
C1440.1uF
C1210.1uFX7R0603
C1570.1uFX7R0603
C1270.1uF
R63 100
RP28 47R
182345
67
C166
22pF
C112
0.1uF
C1420.1uF
RESETn
VVVS
VY[7:0]
VVCLK
VB[7:0]
VCLK
SDA
VVS
VUV[7:0]
VG[7:0]
NDSP_EN
VPEN
VHS
SCL
VVHS
VR[7:0]
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
POWER C
PW171-LGPDP
A
11 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
V25ADJ
V25
+5VIN
VCC
VCC V33
VCC
U29 LM3940IS-3.3
1
23
AD
J
VOVI
R126
510
C2610.1uF
R129
510
+C259
220uF-16V
12
C253
0.1uF
C251
0.1uF+ C250
22uF1
2
C252
22uF
C2690.1uF
+
C254
1000uF-16V
12
C2670.1uF
C2621000pF
U27LM317S
1
23
4
AD
J
VOVI
TA
B
+ C26822uF
12
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
PW171 C
PW171-LGPDP
B
8 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
RBO0
RRE6
VR3
A11
VG5
RRO2
RGE0
RGO6
DGO0
DGE1
D4
WDTEN
DRO4
RGE1
RRE5
A16
VR0
UCSRC
DBO2
EINT0
RBO5
D10
RGO0
A9
VR7
RBE7
RRE0
RGO2 DGO2
D3
RGO5
DBO3
RRE2
DGE3
EINT2
RBO6
DBO0
DRO5
A15
RRO5
DGE2
CS3n
VB1
PDWN
VR5
RGE5
RBO7
RRO3
DGO5
D13
RBE6
D15
RRE1
RRO6
DRE2
DRO7
DBE2
CS0n
VB7
SLEEP1
D14
DBO6
DGO7
DGE4
D9
RRE3
RGO3
RBE3
VB6
RBE0
A5
D5
RRO0
D0
CLKIN
VG4
RGE7
DRE5
DRE3
D11
A2
VB5
MUTE
A18
DBE4
DBE7
VB2
DRO3
A3
A17
RRE7
DBO7
DGE5
A6
CPUEN
DRE4
RBO3
RDK
A10
DGO6
D8
DBE3
DBO4
VB0
A12
EINT1
DGO1
RRE4
RGO7
DRE7
A8
VG7
RRO4
A7
RBO2
DRO1
VB4
VR4
RBO4
RBE4RBE5
D7
VG3
A4
D1
XTALO
VG2
VG6
RRO1
RRO7
XTALI
VG1
DGE6
DRE1
DRO2
RGE2
RGO1
DGO3
VR2
RGE4
A19
VB3
RBE2
DBE5D6
DBO5
DBE0
DBO1
A1
A14
RBO1
DBE6
DRO6
DGE7
DGO4
VG0
DRE0
DGE0A13
RGE3
VR6
D2
DRE6
A0
DBE1
D12
RGO4
RGE6
RBE1
DRO0
VR1
GGE2
GBO4
GRO3
GRE5
GRE1
GBO1
GGO5
GGE3
GBO3
GRO5
GRE0
GBO2
GBE6
GGE7GGE6
GRO4
GBE7
GBE1
GRE6
GGO7
GGO4
GRO2
GBE3
GGE5
GGO2
GGO0
GRE4
GBO0
GGO3
GRE3
GBO7
GRO1
GGE4
GRE2
GBO6
GRO6
GGE0
GRE7
GBE4
GBO5
GRO0
GRO7
GGE1
GGO6
GBE5
GBE2
GBE0
GGO1
PIO4PIO5
V3P
V3P
V3P V3P
V25P
V3P
V25P
V3P
V25
V25
V25
V25V25
V25
V25V25
V3PV25 V25 V25
V25
V25
V3P V3P
V25
V3P
V3P
V33
V3P
V25P
V3P
V25V25
V25
V25
V3P
V25 V25V25
V25
V3P
V3P
V3P
V3P
V3P V3PV3P
C191
0.1uF
C190
0.1uF
R7647
C176
0.1uF
C202
22uF
Y2
XTAL14.31818
R8910K
Power and GroundU18EPW365
A1
A17
A18
A19
B19
B20
B24
D4
D7
D10
D13
D17
D20
D23
G4
G23
H24
J2 K4
K23
M2
M23
N23
N25
P4
U4
U23
W26
Y1
D3
Y23
AA
4A
B1
AB
25A
C4
AC
7A
C10
AC
11A
C13
AC
14A
C17
AC
18A
C20
AC
23A
D22
AE
14A
E20
AE
25A
E26
AF
3A
F5
AF
9A
F16
AF
20A
F21
AF
22
A20
A25
C4
C7
C10
C17
C18
C19
C20
D18
D19
G3
G24
H4
K3
K24
N26
U3
U24
Y24
AA
2A
C19
AD
4A
D7
AD
10A
D17
AD
19A
D20
AD
25A
E21
AF
14A
F18
AF
19A
F26
C3
C13
C24
G25
J1 M1
N24
P3
W2
Y26
AB
24A
C2
AC
21A
D3
AD
6A
D11
AD
14A
D24
AE
8A
E13
AE
16
GN
D1
GN
D2
GN
D3
GN
D4
GN
D5
GN
D6
GN
D7
GN
D8
GN
D9
GN
D10
GN
D11
GN
D12
GN
D13
GN
D14
GN
D15
GN
D16
GN
D17
GN
D18
GN
D19
GN
D20
GN
D21
GN
D22
GN
D23
GN
D24
GN
D25
GN
D26
GN
D27
GN
D28
GN
D29
GN
D30
GN
D31
GN
D32
GN
D33
GN
D34
GN
D35
GN
D36
GN
D37
GN
D38
GN
D39
GN
D40
GN
D41
GN
D42
GN
D43
GN
D44
GN
D45
GN
D46
GN
D47
GN
D48
GN
D49
GN
D50
GN
D51
GN
D52
GN
D53
GN
D54
GN
D55
GN
D56
VD
D1
VD
D2
VD
D3
VD
D4
VD
D5
VD
D6
VD
D7
VD
D8
VD
D9
VD
D10
VD
D11
VD
D12
VD
D13
VC
C5
VD
D14
VD
D15
VD
D16
VD
D17
VD
D18
VD
D20
VD
D21
VD
D22
VD
D23
VD
D24
VD
D25
VD
D26
VD
D27
VD
D28
VD
D29
VD
D30
VD
D31
VD
D32
VD
D33
VD
D34
VC
C1
VC
C2
VC
C3
VC
C4
VC
C6
VC
C7
VC
C8
VC
C9
VC
C10
VC
C11
VC
C12
VC
C13
VC
C14
VC
C15
VC
C16
VC
C17
VC
C18
VC
C19
VC
C20
VC
C21
VC
C22
R378
4.7K
R86
0
PA3
CS2N1
R78
4.7K
PC7
RP4247R
RP3847R
RP4347R
RP3947R
C171
18pF
R82NS
C182
22uF
R80
4.7K
RP3547R
C187
0.1uFC196
22uF
C172
0.1uF
EINT1
C203
0.1uF
Video Port
U18B
PW365
A9B10A10D11C11B11A11D12
C12B12A12B13A13D14C14B14
A14D15C15B15A15D16C16A16
B16
B18A21B21
C21A22
VR0VR1VR2VR3VR4VR5VR6VR7
VG0VG1VG2VG3VG4VG5VG6VG7
VB0VB1VB2VB3VB4VB5VB6VB7
VCLK
VPENVLAVVVS
VFIELDVHS
C183
0.1uF
Display Port
U18C
PW365
Y25AA26AA25AB26AA24AA23AC26AC25
AB23AC24AD26AD23AC22AE24AF25AF24
AE23AF23AD21AE22AE19AE18AD18AE17
AF13AC12AD12AE12AF12AE11AF11AE10
AF10AD9AC9AE9AD8AC8AF8AF7
AE7AF6AE6AC6AE5AD5AF4AE3
AD13AD15AC15AF17AC16AD16
DRE0DRE1DRE2DRE3DRE4DRE5DRE6DRE7
DGE0DGE1DGE2DGE3DGE4DGE5DGE6DGE7
DBE0DBE1DBE2DBE3DBE4DBE5DBE6DBE7
DRO0DRO1DRO2DRO3DRO4DRO5DRO6DRO7
DGO0DGO1DGO2DGO3DGO4DGO5DGO6DGO7
DBO0DBO1DBO2DBO3DBO4DBO5DBO6DBO7
DCLKDVSDHS
DENRDENGDENB
R83 NSR380
4.7K
C204
0.1uF
C177
0.1uF
C184
0.1uFC197
0.1uF
R874.7K
R84NS
C185
0.1uF
CS3N1
C192
0.1uF
EINT2
C175
0.1uF
R79
4.7K
C193
0.1uF
R88
10K
C186
0.1uF
C170
18pF
RP3447R
RP4447R
RP4147R
Misc
U18D
PW365
U2V1V2W1V3V4W3W4AA1AB2AA3AC1AB3AD1AE1AD2AB4AC3AF1AE2
H3H2J4J3K1K2L1L2L3L4M3M4N1N2N3N4
T3T4U1R2R1P2P1R3R4T1T2G2G1H1F1
F2E1Y2
AE15AF15
F3
F4
D1D2
E3E2
C1C2B1B2D5B3A2A3
C5D6B4A4C6B5A5B6
AC5
B9AE4AF2
A6D8C8B7A7B8D9C9
E4
A8
B17
Y3Y4
A0A1A2A3A4A5A6A7A8A9
A10A11A12A13A14A15A16A17A18A19
D0D1D2D3D4D5D6D7D8D9
D10D11D12D13D14D15
RDWR
BHENROMOEROMWERAMOERAMWE
CS0CS1CS2CS3
EXTINT0EXTINT1EXTINT2
NMI
CPUENRESETCLKINMCKEXTDCKEXTUCSRC
WDTEN
RXDTXD
IRRCVR0IRRCVR1
PORTA0PORTA1PORTA2PORTA3PORTA4PORTA5PORTA6PORTA7
PORTB0PORTB1PORTB2PORTB3PORTB4PORTB5PORTB6PORTB7
MODE1
CPUTCLKCPUTDICPUTDO
PORTC0PORTC1PORTC2PORTC3PORTC4PORTC5PORTC6PORTC7
MODE0
MODE2
CPUTMS
XTALIXTALO
RP4047R
R81
4.7K
C189
0.1uF
RP3647R
RP4547R
R850
C174
0.1uF
R379
4.7K
R774.7K
C199
0.1uF
RP3747R
C179
0.1uF
C194
22uF
R3874.7K
Graphics Port
U18A
PW365
U26V24V23V25V26
W25W24W23
H23G26H25P23P24P25P26R23
B25A26D24E23C25B26C26E24
R24R25R26T23T24T25T26U25
F23D25D26F24E25E26F25F26
D21B22C22A23B23D22C23A24
L24K26L25J26K25L26L23
M25H26J25J23J24M24M26
GRE0GRE1GRE2GRE3GRE4GRE5GRE6GRE7
GGE0GGE1GGE2GGE3GGE4GGE5GGE6GGE7
GBE0GBE1GBE2GBE3GBE4GBE5GBE6GBE7
GRO0GRO1GRO2GRO3GRO4GRO5GRO6GRO7
GGO0GGO1GGO2GGO3GGO4GGO5GGO6GGO7
GBO0GBO1GBO2GBO3GBO4GBO5GBO6GBO7
GCLKGPENGVSGHSGSOGGFIELDPLLCLK
GCLKOUTGFBKGREF
GBLKSPLGCOAST
GHSFOUTGADCCLK
C181
0.1uF
L29 FB_11_OHM_500MA
C201
0.1uF
C195
0.1uF
C200
0.1uF
C178
0.1uF
L30 FB_11_OHM_500MA
C180
0.1uF
PC6
C198
0.1uF
CLKIN1
C173
0.1uF
PA4
CS0N1
C188
0.1uF
GGE[7:0]
VVS
GCOAST
DGE[7:0]
PDWN
DRE[7:0]
DENG
MUTE
ICSSTD
3WSLE
GGO[7:0]
GCLK
MCKEXT
ROMOEn
GBO[7:0]
DBE[7:0]
NMI
DENR
NDSP_EN
GRE[7:0]
DHS
DCLK
ROMWEn
RDn
VFIELD
ICSDAT
DTXON
GFBK
DGO[7:0]
GAFEOE
ICSCLK
DCKEXT
GBE[7:0]
VR[7:0]
GRO[7:0]
VCLK
GBLKSPL
VGASEL
A[19:0]
VPPEN
GDFEOE
GVS
in/ext
VB[7:0]
VPEN
TXD
GPEN
SCL
DVS
VVINT
SDA
GHSRESET
DRO[7:0]
RXD
VG[7:0]
IRRCVR1
D[15:0]
DENB
VHS
ICSSTM
CS1n
DBO[7:0]
3WSCL3WSDA
SLEEP1
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
TMDS OUTPUT C
PW171-LGPDP
Custom
9 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
DRE3
DRO7
DBE1
DGE4DGE5
DGE3
DBO4
DBE4
DGO4
DRO4
DBE5
DGE7
DGE7
DRE7
DBE6
TX1+
DBO0
TX2-
DBE5
DGE6
DGO1
TXC+
DBE0
DBO2
DBE3
DGE2
DRE1
DGO0
DBE0
DBO7
DRO0
DRO6
DRE0
DRO7
DGO5
DGE0
DGO7
DGE5
DRE3
DRO1
DRO4
DRE4
DGO6
DGO4
DGE0
DGO2
DBE6
DGE3
DRE4
DBE3
DRE2
DBO3
DBO7
DBO0
DRO3
DBO2
DGO2DGO3
DBE2
DBE1
DRO0
DRE6
DBO4
TX0+
DGE6
DRO3
DRO6
TX2+
DRE5
DRO2
DRO5
DRE2
TX0-
DBE7
DGE2
DRE7
DBE2
DRE0
DGO3
DRO5
DRO1
DBO6
DBE4
DBO6
TXC-
DGO1
DBO1
DGE1
DRE6
DBO5
DGO7
DRE1
DGO5
DGO0
DBO3
DBE7
DRE5
DGE4
DRO2
DGE1
DGO6
TX1-
DBO1
DBO5
V33L
V33L
V33T
VCC
V33L
VCC
V33L
V33L
V33L
V33L
V33L
C228
0.1uF
U19 Sil150
16151413121110
9
654321
10099
9796959493929190
8078767784838224
8305688176681
73157
89
86
47
33
19
4039
4342
4645
3534
32
555453525150494865646362616059587574737271706968
983638441885
6779
3741
25
26
2021222327282987
DIE0DIE1DIE2DIE3DIE4DIE5DIE6DIE7
DIE8DIE9DIE10DIE11DIE12DIE13DIE14DIE15
DIE16DIE17DIE18DIE19DIE20DIE21DIE22DIE23
IDCKDEHSYNCVSYNCCTL1CTL2CTL3EDGE
VCCVCCVCCVCC
IVCCIVCCIVCC
GNDGNDGND
GND
PGND2
AGND
AGND
PGND1
TX0+TX0-
TX1+TX1-
TX2+TX2-
TXC+TXC-
EXT_SWING
DIO16DIO17DIO18DIO19DIO20DIO21DIO22DIO23DIO8DIO9DIO10DIO11DIO12DIO13DIO14DIO15DIO0DIO1DIO2DIO3DIO4DIO5DIO6DIO7
IVCCAVCCAVCCAVCC
PVCC1PVCC2
GNDGND
AGNDAGND
PIXS
PD
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R95
NU
+C2051uF
C227
0.1uF
R91
0
U20LM2937_SOT223
1
2
3
4
VI
GN
D
VO
TA
B
L31
200+ Ohm
R96
10K
C207330pF
C2260.1uF
JP4
HDR_34X2
1 23 45 67 89 1011 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 3233 3435 3637 3839 4041 4243 4445 4647 4849 5051 5253 5455 5657 5859 6061 6263 6465 6667 68
L33
200+ Ohm
C2210.1uF
C222100pF
+ C224
22uF
L32
200+ Ohm
+ C22310uF
C218330pF
C2250.1uF
R93 400
C219
10uF
C206
10uFC208330pF
R94
NC
C229
47uF
R92
10K
C217330pF
C216330pF
C209330pF
C210330pF
C220
10uF
C2150.1uF
C211330pF
J6
DVI_V
123456789
101112131415161718192021222324
25
26
C1C2C3C4C5C6
27
28
DATA2-DATA2+DATA2/4_SHLDDATA4-DATA4+DDC_CLKDDC_DATAA_VSYNCDATA1-DATA1+DATA1/3_SHLDDATA3-DATA3++5VGNDH_PLUG_DETDATA0-DATA0+DATA0/5_SHLDDATA5-DATA5+CLK_SHLDCLK+CLK-
SHELL1
SHELL2
A_REDA_GREENA_BLUEA_HSYNCA_GND1A_GND2
NC1
NC2
C212330pF
C213330pF
C214330pF
R90
0
DRO[7:0]DRE[7:0]
DGO[7:0]
DVS
DBO[7:0]DBE[7:0]
DENG
DRE[7:0]
DENR
DHSDENG
DHS
DBE[7:0]
DCLK
DGE[7:0]
DENB
DRO[7:0]
DCLK
DGE[7:0]
DVS
DGO[7:0]
DBO[7:0]
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
VIDEO INPUT C
PW171-LGPDP
Custom
5 12Thursday, December 09, 2004
Title
Size File Rev
Date: Sheet of
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Drawn by: Checked by: Approved by:
SDA
VVPA
VY1VY0
VY4
VX1
VVSCAP
VLUMA
CVIDVVUV7
VVUV1
VCBIN
VCCB
VCCRVVY6
VVUV6
VVUV0
VVIN1
VVGCAP
VVREF
VUV1
VVY4
VYIN
VCRIN
VUV0
CHROM
VX2
SDA5V
VUV2
VCCB
VY7
VTV
VVY1
VVUV5
VVY5
VLLC1
VUV3
SDA5V
SCL5V
VCCG
VVIN3
VVRT
SCL
VVUV3
VVGPA
VCHROMA
SCL5V
VVHS
VVY3
VCCG
VCVID
VY5
VBOX
CCV2
VY2
VBOX
VUV6
VVUV4VUV5
CCV2
LUMAVVUV2
VY6
VVY2
VVY0
VUV7
VVVS
VVY7
VDOEn
VY3
VUV4
VCCR
VCCVAAV
+5VT
VAAV
VCC
+5V+5VT
VCCV
V33V33
V33
+5VIN
VAAV
VAAV
VCCV
VAAV
VCC
V33V33 VAAVVAAV
V33
VAAV
V33
VCCV
V33
V33
VAAV
C284
33pF
R4375
C285
33pF
L25
3uH
C87 680nF
L21
3uH
R4775
R35
2K
R31
6.8K
R54 51K
C1070.1uF
C280 220nF
R4475
C82 220nF
J4
CON19
12345678910111213141516171819
R60 0
C950.1uF
C77
330pF
C72
68nF R34
2K
R5247
L19FB_420_OHM_200MA
R33
2K
L20
3uH
C88 680nF
234
1
J3
S+AV
1324
65
8
7
R32
10K
L22
3uH
R4875
C79
330pF
C1020.1uF
R26 13K
RP24 47RU11
VPC3230D_C5
123
456
7
8
9
10
1112
1314
15
16
17
18
1920212223
24
2526
2827
2930
31323334
35
36
37383940
41424344
45
46
47484950
51
52
53
54
55
5657
58
59
60
61
6263
64 65
66
67
68
69
70
7172737475
7677
78
79
80
B1/CB1ING1/Y1INR1/CR1IN
B2/CB2ING2/Y2INR2/CR2IN
AS
GF
1
NC1
VSUPCAP
VS
UP
D
GN
DD
1
GN
DC
AP
SCLSDA
RESQ
TEST
VGAV
YCOEQ
FFIEFFWE
FFRSTWFFREFFOE
CLK20
GN
DP
AV
SU
PP
A
LLC1LLC2
VS
UP
LLC
GN
DLL
C
Y7Y6Y5Y4
GN
DY
VS
UP
Y
Y3Y2Y1Y0
C7C6C5C4
VS
UP
C
GN
DC
C3C2C1C0
GN
DS
Y
VS
UP
SY
INTLC
AVO
FSY/HC
MSY/HSVS
FPDAT
VS
TB
Y
CLK5
NC2
XTAL1XTAL2
AS
GF
2
GN
DF
VRT
I2CSEL
ISG
ND
VS
UP
F
VOUT
CINVIN1VIN2VIN3VIN4
VS
UP
AI
GN
DA
I
VREF
FB1IN
AIS
GN
D
R572K
C9218pF
C73
0.1uF
R4075
L26FB_420_OHM_200MA
C84 220nF
C970.1uF
C69
0.1uF
R58470
R4975
R4547
C80220nF
C75
0.1uF
C81
330pF
C76220nF
C1000.1uF
C930.1uF
C83 220nF
C9118pF
D15
1N1183A
1 2
RP23 47R
C990.1uF
D16
1N1183A
1 2
R61 0
Q33904
1
23
L23
3uH
R512K
C74
47uF
C89 680nF
R28 13K
R17 3.3K
Z1
XTAL_20.25
R530
R30 470
U10
Z86229
151416
135
7
10
461 11
9
8
3218
17
12SCLSDASDO
VIN INTROHIN
VIDED
REF
SENSMSASEL VSSA
LPF
CSYNC
BLUEGREEN
RED
BOX
VDD
RP21 47R
R23 13K
R3822K
C286
33pF
R25 33
R5010K
C1090.1uF
L24
3uH
C287
33pF
C9622uF
R55 470
C70
560pF
C1080.1uF
C1030.1uF
C85 1nF
C9422uF
R36
2K
C1100.1uF
R1822K
C71
6.8nF
R20 8.2K
R1922K
C86 680nF
C90
4.7uF
C1040.1uF
Q1
SN7002
1
2 3
G
S D
R3975
Q2
SN7002
1
2 3
G
S D
R4175
R22 NC
C10522uF
C1060.1uF
RP25 47R
C78220nF
R3722K
C980.1uF
C1110.1uF
C1010.1uF
RP22 47R
R4275
VY[7:0]
in/ext
RESETn
STBLED
SCL
POWER_ON
VVCLK
IR
CR
VFIELDVVVS
MUTE
SDA
CB
VVHS
Y
VUV[7:0]
VVINT
SLEEP1
Main (Video)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
03_AUDIO
03_AUDIO
SIFSCL5VSDA5VAUDIO OUTLAUDIO OUTR
04_MCU+AMP
04_MCU+AMP
IRPOWER_ONRELAYMUTEOUTAOUTBMUTE1
02_INPUT
02_INPUT
OUTAOUTBAUDIO OUTLAUDIO OUTBSIFSDA5VSCL5V
IRMUTE
MUTE1POWER_ON
SDA
SCL
Audio/Tuner
Audio/Tuner
Audio/Tuner
KeypadRemote control receiverExternal L/R Speakers
Remote control
Basic Operations & Circuit Description
MODULE There are 1 pc. panel and 8 pc.s PCB including 2 pc.s Y/Z Sustainer board, 2 pc.s Y Driveboard, 2 pc.s X (left and right) Extension PCB, 1 pc. Control (Signal Input) and 1 pc. Power
board in the Module.
SET There are 5 pc.s PCBs including 1 pc. Tuner/Audio board, 1 pc. Keypad board, 1 pc.
Remote Control Receiver board, 1 pc. L/R Speakers and 1 pc. Main (Video) board in the SET.
Parts position
Power SW
Internal Speaker (Right) Power Supply Internal Speaker (Left)
Z-Sustainer Y-Sustainer
External Speaker Terminals
Tuner/Audio
EMI filter + AC Inlet
Control (Signal Input)
Main (Video)Local key
Stand
X left Extension
X right Extension
Y-Drive Top
Y-Drive Bottom
PCB function1. Power:
(1). Input voltage: AC 110V~240V, 47Hz~63Hz.Input range: AC 90V(Min)~265V(Max) auto regulation.
(2). To provide power for PCBs.2. Main (Video InterFace) board: To converter TV signals, S signals, AV signals, Y Pb/
Cb Pr/Cr signals, DVI signals and D-SUB signals to digital ones and to transmit toControl board.
3. Control board: Dealing with the digital signal for output to panel.4. Y-Sustainer / Z-Sustainer board:
(1). Receiving the signals from Control and high voltage supply.(2). Output scanning waveform for Module.
5. Y-Drive board: Receive signal from Y sustainer, output horizontal scanning wave-form to the panel.
6. X (left and right) extension board: Output addressing signals.7. Tuner/Audio Board: : : : : Amplifying the audio signal to the internal or external speakers
of which selected.
PCB failure analysis
1. CONTROL: a. Abnormal noise on screen. b. No picture.2. MAIN (VIDEO): a. Lacking color, Bad color scale.
b. No voice.c. No picture but with signals output, OSD and back light.d. Abnormal noise on screen.
3. POWER: No picture, no power output.4. Z - Sustainer:a. No picture.
b. Color not enough.c. Flash on screen.
5. Y - Sustainer: Darker picture with signals.
6. Audio Bard: a. No voice. (Make sure status: Mute / Internal, External speaker) b. Noise7. Y/Z - Sustainer: The component working temperature is about 55oC.
If the temperature rises abnormal, this may be a error point.
Basic operation of Plasma Display
1. After turning on power switch, power board sends 5Vst-by Volt to Micro ProcessorIC waiting for ON signals from Key Switch or Remote Receiver.
2. When the ON signal from Key Switch or Remote Receiver is detected, Micro Processorwill send ON Control signals to Power. Then Power sends (5Vsc, 9Vsc, 24V and RLYON, Vs ON) to PCBs working. This time VIF will send signals to display back light,OSD on the panel and start to search available signal sources. If the audio signalsinput, them will be amplified by Audio AMP and transmitted to Speakers.
3. If some abnormal signals are detected (for example: over volts, over current, overtemperature and under volts), the system will be shut down by Power off.
Main IC Specifications
- PW171 Image Processor - AD9883A 110MSPS/140MSPS Analog Interface for Flat Panel Displays - NV320 Video Enhancement Processor - VCP 323XD comb Filter Video Processor - SiI161B Panel Link Receiver - Z86229 NTSC Line 21 CCD Decoder - TDA9850 BTSC stereo/SAP decoder(only for the Model with Turner) - NJW1144 Audio Processor
Product Specification:PW171 ImageProcessor
C
Preliminary
General DescriptionPW171 is a highly integrated “system-on-a-chip” that interfaces analog, digital, and video inputs in virtually any format to a flat panel monitor or multimedia display. PW171 is pin-compatible with the PW364.
An embedded SDRAM frame buffer and memory controller perform frame rate conversion. Computer images from VGA to UXGA at almost any refresh rate can be resized to fit on a fixed-frequency target display device with any resolution up to UXGA with full 24-bit color.
PW171 includes advanced second-generation image scaling that provides completely programmable, horizontal and vertical image scaling.
PW171 also includes advanced second-generation sync decoding which provides full support for a wide variety of sync types. This includes interlaced, progressive, sync-on-green, and TMDS DE (Data Enable) only.
PW171 ImageProcessor supports NTSC or PAL video data with a 4:3 aspect ratio and 16:9 aspect ratio sources, such as DVD or HDTV. Nonlinear scaling and separate horizontal and vertical scalers allow these inputs to be resized optimally for the native resolution and aspect ratio of the display device.
PW171 uses an integrated PLL to synchronize the display interface timing to the input timing. This requires only a single external crystal to generate all necessary clocks for the system.
An integrated OSD controller provides bit-mapped based OSDs with 16 colors from a 64K color palette. The OSD controller supports transparent and translucent functions.
PW171 provides a Pulse Width Modulation (PWM) output for low cost backlight or audio control.
With reference source code and an on-chip microprocessor, manufacturers can develop feature-rich products with rapid time-to-market. Programmable features include the user interface, custom start-up screen, all automatic imaging features, and special screen effects.
PW171 incorporates new features while maintaining backward compatibility with the PW264 and PW364 ImageProcessors.
Features!!!!Second-generation Image Scaling !!!!Second-generation Automatic Image Optimization !!!!Color Space Converter for graphics inputs!!!!Video processing!!!!Picture-In-Picture (PIP)!!!!Frame rate conversion!!!!Color matrix for improved color temperature adjustment!!!!On-board PLLs to generate MCLK and DCLK!!!!On-screen display!!!!On-chip microprocessor!!!!JTAG debugging port !!!!8-bit, 9-bit, or 10-bit display outputs !!!!24-bit CPU Addressing !!!!Hardware 2-Wire serial bus support !!!!Hardware PWM output
Applications!!!!LCD Monitors!!!!Plasma Displays!!!!Multimedia Displays
XGA/SXGA/UXGA Flat Panel Display Controller Id to result in a personal injury or loss of life. Customers using or selling Pixelworks devices for use in such applications do so at their ris
REV. A
Information furnished by Analog Devices is believed to be accurate andreliable. However, no responsibility is assumed by Analog Devices for itsuse, nor for any infringements of patents or other rights of third parties thatmay result from its use. No license is granted by implication or otherwiseunder any patent or patent rights of Analog Devices.
aAD9883A
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel:
Fax:
110 MSPS/140 MSPS Analog Interface for Flat Panel Displays
FUNCTIONAL BLOCK DIAGRAM
RAIN ROUTA
GAIN GOUTA
BAIN BOUTA
MIDSCV
SYNCPROCESSINGAND CLOCKGENERATION
HSYNC
COAST
CLAMP
FILT
DTACK
HSOUT
VSOUT
SOGOUT
REF REFBYPASS
SERIAL REGISTERAND
POWER MANAGEMENT
SCL
SDA
A0AD9883A
CLAMP8
A/D
CLAMP8
A/D
CLAMP8
A/D
FEATURES
140 MSPS Maximum Conversion Rate
300 MHz Analog Bandwidth
0.5 V to 1.0 V Analog Input Range
500 ps p-p PLL Clock Jitter at 110 MSPS
3.3 V Power Supply
Full Sync Processing
Sync Detect for “Hot Plugging”Midscale Clamping
Power-Down Mode
Low Power: 500 mW Typical
4:2:2 Output Format Mode
APPLICATIONS
RGB Graphics Processing
LCD Monitors and Projectors
Plasma Display Panels
Scan Converters
Microdisplays
Digital TV
GENERAL DESCRIPTIONThe AD9883A is a complete 8-bit, 140 MSPS monolithic analoginterface optimized for capturing RGB graphics signals frompersonal computers and workstations. Its 140 MSPS encoderate capability and full power analog bandwidth of 300 MHzsupports resolutions up to SXGA (1280 × 1024 at 75 Hz).
The AD9883A includes a 140 MHz triple ADC with internal1.25 V reference, a PLL, and programmable gain, offset, andclamp control. The user provides only a 3.3 V power supply,analog input, and Hsync and COAST signals. Three-stateCMOS outputs may be powered from 2.5 V to 3.3 V.
The AD9883A’s on-chip PLL generates a pixel clock from theHsync input. Pixel clock output frequencies range from 12 MHz to
140 MHz. PLL clock jitter is 500 ps p-p typical at 140 MSPS.When the COAST signal is presented, the PLL maintains itsoutput frequency in the absence of Hsync. A sampling phaseadjustment is provided. Data, Hsync, and clock output phaserelationships are maintained. The AD9883A also offers full syncprocessing for composite sync and sync-on-green applications.
A clamp signal is generated internally or may be provided bythe user through the CLAMP input pin. This interface is fullyprogrammable via a 2-wire serial interface.
Fabricated in an advanced CMOS process, the AD9883A isprovided in a space-saving 80-lead LQFP surface-mount plasticpackage and is specified over the 0°C to 70°C temperature range.
nDSP Corporat ion NV320 Data Sheet
NV320 Video Enhancement Processor
1.0 Introduction
The NV320 is a single-chip, programmable video display processor providing advanced features for progressive scan, high frame-rate TV. The NV320 improves upon the functional-ity of the NV320P by handling non-standard video input signals. Other feature enhance-ments include DCTI, Black Level Stretch, and Saturation Control.
The NV320 offers the following features.
1.1 Highly Integrated Video Processor• Three, on-chip, 10-bit Digital-to-Analog
Converters (DACs)• Built-in memory controller supporting
SDRAM or SGRAM• 0.35µ CMOS process• 3.3V power supply with 5V tolerant I/Os• Standard 208-pin PQFP1.2 Video Input • Multiple video input modes
- Data acquisition mode- Line-locked mode- DVD mode
• Multiple video input data formats- Digital 16-bit YUV (4:2:2) or 12-bit YUV (4:1:1)- Digital 8-bit YUV (ITU-R 656)- Digital 24-bit YUV (4:4:4)
1.3 Noise Reduction • Motion adaptive noise reduction filter1.4 Color Processing• Built-in color space conversion• Selectable output color space: YUV or
RGB1.5 Video Processing• Advanced, non-linear video processing• Motion compensated deinterlacing• Programmable peaking• Non-linear interpolation• Background coloring
• Anti-flickering circuitry• NTSC/PAL to SDTV 480p format conver-
sion• Frame rate up-conversion (50Hz up to
75Hz for PAL, 60Hz up to 90Hz for NTSC)• DCTI (Digital Color Transient Improve-
ment)• Black Level Stretch• Saturation Control1.6 Host Interface• I2C interface• No programming needed for default mode
application1.7 General Description and Applications
The NV320 is a single chip digital video pro-cessor for progressive and digital TV applica-tions. It provides high quality video processing including video noise reduction, motion compensation, sharpness enhance-ment, and resolution enhancement. It also provides frame rate conversion and progres-sive scan conversion with deinterlacing.
The NV320 is a CMOS mixed signal circuit highly integrated with three, 10-bit digital-to-analog converters controlled by the I2C inter-face. The NV320 accepts 16-bit YUV (4:2:2), 12-bit YUV (4:1:1), and 8-bit YUV (ITU-R 656) simultaneously, or it accepts 24-bit YUV (4:4:4) input from a front-end digital video color decoder or from an analog-to-digital converter. Additionally, NV320 supports multi-ple video input modes: acquisition mode, line-locked mode, and DVD mode.
The NV320 has an on-chip detection logic block that corrects non-standard input signals before processing.
Applications for the NV320 chip are listed here.• Progressive scan televisions• Digital televisions (the chip is DTV/HDTV
ready)
nDSP Corporat ion NV320 Data Sheet
• Internet televisions• Home theater and multimedia televisions• Video conferencing
2.0 Ordering Information
3.0 Block Diagram of NV320
Figure 1. Block Diagram of NV320
Part Number
NV320
Package PQFP 208
DescriptionPlastic quad flat pack-age, 208 leads
Version 1.0
nDSP VideoEnhancement Processor
Timing
Controller
Memory
Controller
10-Bit DAC
10-Bit DAC
10-Bit DAC
SDRAM/SGRAM Interface
DigitalYUV/RGB
Y/G
U/B
V/R
PCLK
HSQ
HBQ
VSQ
VBQ HostInterface
Timing
Generator
Input Video Selector & Formatter
8-bit YUV ITU R-656
LLC LLAD2
HS/CLP VS
LLA CLV HREFO
SCLSDA
VPC 323xD Comb Filter Video Processor1. IntroductionThe VPC 323xD is a high-quality, single-chip video front-end, which is targeted for 4:3 and16:9. 50/60 Hz and 100/120 Hz TV sets. It can be combined with other members of theDIGIT3000 IC family (such as DDP 331x) and/or it can be used with 3rd-party products.
The main features of the VPC 323xD are - High-performance adaptive 4H comb filter Y/C separator with adjustable vertical peaking. - Multi-standard color decoder PAL/NTSC/SECAM including all substandards. - Four CVBS, one S-VHS input, one CVBS output. - Two RGB/YCrCb component inputs, one Fast Blank (FB) input. - Integrated high-quality A/D converters and associated clamp and AGC circuits. - Multi-standard sync processing. - Linear horizontal scaling (0.25......4), as well as nonlinear horizontal scaling 'Panoramavision'. - PAL+ preprocessing. - Line-locked clock, data and sync, or 656-output interface. - Peaking, contrast, brightness, color saturation and tint for RGB/YCrCb and CVBS/S-VHS. - High-quality soft mixer controlled by Fast Blank. - PIP processing for four picture sizes (1/4, 1/9, 1/16, or 1/36 of normal size) with 8-bit
resolution. - Control interface for external field memory. - I2C-bus interface. - One 20.25-MHz crystal, few external components. - 80-pin PQFP package.
SiI 161B PanelLink® Receiver August 2002 Data Sheet
General Description Features The SiI 161B receiver uses PanelLink Digital technology to support high-resolution displays up to UXGA (25-165MHz). This receiver supports up to true color panels (24 bits per pixel, 16M colors) with both one and two pixels per clock.
All PanelLink products are designed on a scaleable CMOS architecture, ensuring support for future performance enhancements while maintaining the same logical interface. System designers can be assured that the interface will be stable through a number of technology and performance generations.
PanelLink Digital technology simplifies PC and display interface design by resolving many of the system level issues associated with high-speed mixed signal design, providing the system designer with a digital interface solution that is quicker to market and lower in cost.
• Low Power Operation: 280mA max. current consumption at 3.3V core operation
• Time staggered data output for reduced ground bounce and lower EMI
• Sync Detect feature for Plug & Display • Cable Distance Support: over 5m with twisted-
pair, fiber-optics ready • ESD tolerant to 5kV (HBM on all pins) • Compliant with DVI 1.0 (DVI is backwards
compatible with VESA® P&DTM, FPDI-2TM and DFP)
• HSYNC de-jitter circuitry enables stable operation even when HSYNC contains jitter
• Low power standby mode • Automatic entry into standby mode with clock
detect circuitry • Standard and Pb-free packages (see page 25).
• Complete Stand-Alone Line 21 Decoder for Closed-Captioned and Extended Data Services (XDS)
• Preprogrammed to Provide Full Compliance withEIA–608 Specifications for Extended Data Services
• Automatic Extraction and Serial Output of SpecialXDS Packets (Time of Day, Local Time Zone, andProgram Blocking)
• Programmable XDS Filter for a Specific XDS Packet
• Cost-Effective Solution for NTSC Violence Blockinginside Picture-in-Picture (PiP) Windows
• Minimal Communications and Control Overhead Pro-vide Simple Implementation of Violence Blocking,Closed Captioning, and Auto Clock Set Features
• Programmable, On-Screen Display (OSD) for Creat-ing Full Screen OSD or Captions inside a Picture-in-Picture (PiP) Window
• User-Programmable Horizontal Display Position foreasy OSD Centering and Adjustment
• I2C Serial Data and Control Communication
• Supports 2 Selectable I2C Addresses
Capable of processing Vertical Blanking Interval (VBI)data from both fields of the video frame in data, the Z86229Line 21 Decoder offers a feature-rich solution for any tele-vision or set-top application. The robust nature of theZ86229 helps the device conform to the transmission formatdefined in the Television Decoder Circuits Act of 1990, andin accordance with the Electronics Industry Associationspecification 608 (EIA–608).
The Line 21 data stream can consistof data from several datachannels multiplexed together. Field 1 consists of four datachannels: two Captions and two Texts. Field 2 consists offive additional data channels: two Captions, two Texts, andExtended Data Services (XDS). The XDS data structure is
defined in EIA–608. The Z86229 can recover and displaydata transmitted on any of these nine data channels.
The Z86229 can recover and output to a host processor viathe I2C serial bus. The recovered XDS data packet is furtherdefined in the EIA–608 specification. The on-chip XDS fil-ters in the Z86229 are fully programmable, enabling recov-ery of only those XDS data packets selected by the user. Thisfunctionality allows the device to extract the required XDSinformation with proper XDS filter setup for compatibilityin a variety of TVs, VCRs, and Set-Top boxes.
In addition, the Z86229 is ideally suited to monitor Line 21video displayed in a PiP window for violence blocking,CCD, and other XDS data services. A block diagram of theZ86229 is illustrated in Figure 1.
!"
#$ %
&%
" '
I2C-bus controlled BTSC stereo/SAP decoder TDA9850FEATURES
- Quasi alignment-free application due to automatic adjustment of channel separation via
I2C-bus
- Dbx noise reduction circuit
- Dbx decoded stereo, Second Audio Program (SAP) or mono selectable at the AF outputs
- Additional SAP output without dbx, including de-emphasis
- High integration level with automatically tuned integrated filters
- Input level adjustment I2C-bus controlled
- Alignment-free SAP processing
- Stereo pilot PLL circuit with ceramic resonator, automatic adjustment procedure for
stereo channel separation, two pilot thresholds selectable via I2C-bus
- Automatic pilot cancellation
- Composite input noise detector with I2C-bus selectable thresholds for stereo and SAP off
- I2C-bus transceiver.
NJW1144 AUDIO PROCESSORGENERAL DESCRIPTION
The NJW1144 is a sound processor includes all of the functions required to process the
audio signal for TV, such as tone control, balance, volume, mute, and AGC functions.
Also the NJW1144 performs BBE sound enhancement and SRS 3D Stereo. The BBE
regenerates high definitive and nearly real sound, and SRS 3D Stereo regenerates 3D sur-
round sound with only two speakers.
All of the internal stats and variables are controlled by I2C BUS interface.
FEATURES
- Operating Voltage 8 to 13V
- I2C BUS Interface
- BBE Sound Enhancement (Low Boost and High Boost: 15dB max.)
- Internal 6 Input Audio Selectors and Monitor Output
- The AGC circuit reduces volume difference among input sources.
- Variable AGC Compression Level via I2C (4-levels)
- SRS 3D Stereo and Simulated Stereo
- Variable Surround Effect Level via I2C
- Low Noise VCA
- Bi-CMOS Technology
- Package Outline SOP40
Product Specification of PDP Module
0. Warnings and CautionsWARNING indicates hazards that may lead to death or injury if ignored.CAUTION indicates hazards that may lead to injury or damage to property if ignored.
WARNING1) This product uses a high voltage (450 V max.). Do not touch the circuitry of this product with your hands when
power is supplied to the product or immediately after turning off the power. Be sure to confirm that the voltageis dropped to a sufficiently low level.
2) Do not supply a voltage higher than that specified to this product. This may damage the product and may cause afire.
3) Do not use this product in locations where the humidity is extremely high, where it may be splashed with water,or where flammable materials surround it. Do not install or use the product in a location that does no satisfy thespecified environmental conditions. This may damage the product and may cause a fire.
4) If a foreign substance (such as water, metal, or liquid) gets inside the product, immediately turn off the power.Continuing to use the products it may cause fire or electric shock.
5) If the product emits smoke, an abnormal smell, or makes an abnormal sound, immediately turn off the power. Ifnoting is displayed or if the display goes out during use, immediately turn off the power. Continuing to use theproduct as it is may cause fire or electric shock.
6) Do not disconnect or connect the connector while power to the product is on. It takes some time for the voltageto drop to a sufficiently low level after the power has been turned off. Confirm that the voltage has dropped to asafe level before disconnecting or connecting the connector. Otherwise, this may cause fire, electric shock, ormalfunction.
7) Do not pull out or insert the power cable from/to an outlet with wet hands. It may cause electric shock.
8) Do not damage or modify the power cable. It may cause fire or electric shock.
9) If the power cable is damaged, or if the connector is loose, do not use the product; otherwise, this can lead to fireor electric shock.
10) If the power connector or the connector of the power cable becomes dirty or dusty, wipe it with a dry cloth. Otherwise, this can lead to fire.
Product Specification of PDP Module
CAUTIONGeneral
1) Do not place this product in a location that is subject to heavy vibration, or on an unstable surface such as aninclined surface. The product may fall off or fall over, causing injuries.
2) When moving the product, be sure to turn off the power and disconnect all the cables. While moving theproduct, watch your step. The product may be dropped or fall, leading to injuries of electric shock.
3) Do not place this product in a location that is subject to heavy vibration, or on an unstable surface such as aninclined surface. The product may fall off or fall over, causing injuries.
4) Before disconnecting cable from the product, be sure to turn off the power. Be sure to hold the connector whendisconnecting cables. Pulling a cable with excessive force may cause the core of the cable to be exposed orbreak the cable, and this can lead to fire or electric shock.
5) This product should be moved by two or more persons. If one person attempts to carry this product alone, he/shemay be injured.
6) This product contains glass. The glass may break, causing injuries, if shock, vibration, heat, or distortion isapplied to the product.
7) The temperature of the glass surface of the display may rise to 80°C or more depending on the conditions of use.If you touch the glass inadvertently, you may be burned.
8) Do not poke or strike the glass surface of the display with a hard object. The glass may break or be scratched. Ifthe glass breaks, you may be injured.
9) If you glass surface of the display breaks or is scratched, do not touch the broken pieces or the scratches withbare hands. You may be injured.
10) Do not place an object on the glass surface of the display. The glass may break or be scratched.
Product Specification of PDP Module
USE1) Because this product uses a high voltage, connecting or disconnecting the connectors while power is supplied to
the product may cause malfunctioning. Never connect or disconnect the connectors while the power is on.Immediately after power has been turned off, a residual voltage remains in the product. Be sure to confirm thatthe voltage has dropped to a sufficiently low level.
2) Watching the display for a long time can tire the eyes. Take a break at appropriate intervals.
3) PDP ’s brightness and contrast ratio is lower than that of the CRT. The picture is dimmer with surrounding light and better for viewing in dark condition.
4) Do not cover or wrap the product with a cloth or other covering while power is supplied to the product.
5) Before turning on power to the product, check the wiring of the product and confirm that the supply voltage iswithin the rated voltage range. If the wiring is wrong or if a voltage outside the rated range is applied, theproduct may malfunction or be damaged.
6) Do not store this product in a location where temperature and humidity are high. This may cause the product tomalfunction. Because this product uses a discharge phenomenon, it may take time to light (operation may bedelayed) when the product is used after it has been stored for a long time. In this case, it is recommended to lightall cells for about 2hours (aging).
7) If the glass surface of the display becomes dirty, wipe it with a soft cloth moistened with a neutral detergent. Donot use acidic or alkaline liquids, or organic solvents.
8) Do not tilt or turn upside down while the module package is carried, the product may be damaged.
9) This product is made from various materials such as glass, metal, and plastic. When discarding it, be sure tocontact a professional waste disposal operator.
Repair and MaintenanceBecause this product combines the display panel and driver circuits in a single module, it cannot be repaired ormaintained at user’s office or plant. Arrangements for maintenance and repair will be determined later
Product Specification of PDP Module
1. GENERAL DESCRIPTION
DESCRIPTIONThe PDP42V6#### is a 42-inch 16:9 color plasma display module with resolution of 852(H)× 480(V) pixels.This is the display device which offers vivid colors with adopting AC plasma technology by LG Electronics Inc.
FEARURESHigh peak brightness (1000cd/m2 Typical) and high contrast ratio (3000:1 Typical) enables user to createhigh performance PDP SETs.
APPLICATIONS
Public information displayVideo conference systemsEducation and training systems
Product Specification of PDP Module
ELECTRICAL INTERFACE OF PLASMA DISPLAYThe PDP42V6#### requires only 8bits of digital video signals for each RGB color.In addition to the video signals, six different DC voltages are required to operate the display.The PDP42V6#### is equipped with P-CUBE function which analyzes display signals to optimize systemcontrol factor for showing the best display performance.
2ndpixelcolumn
GENERAL SPECFICATIONS
Model NameNumber of PixelsPixel PitchCell PitchDisplay Area Outline Dimension Pixel Type Number of Gradations Weight
Aspect RatioPeak BrightnessContrast Ratio
Power ConsumptionLife-time
: PDP42V6#### (42V6#### Model): 852(H) × 480(V) (1pixel=3 RGB cells) : 1080 (H) × 1080 (V): 367 (H) × 1080 (V) (Green Cell basis): 920.1(H) × 518.4(V) ±0.5mm: 1005(H) × 597(V) × 61(D)±1mm: RGB Closed type: (R)256 × (G)256 × (B)256 (16.7 Mega colors): 14.8 Kg ± 0.5 Kg (Net 1EA)
111 Kg ± 5 Kg (5EA/1BOX): 16:9: Typical 1000cd/ (1/25 White Window): Average 60:1 (In a bright room with 150Lux at center): Typical 3000:1 (In a dark room 1/25 White Window pattern at center): Typical 220 W (Full White): more than 60,000 Hours of continuous operation
Life-time is defined as the time when the brightness level becomes half of its initial value.
Pixel Pitch(width) Cell pitch
cell
pixel
1stpixelcolumn
851thpixelcolumn
852thpixelcolumn
pitc
h(he
ight
)
1st pixelrow2nd pixelrow
3rd pixelrow
479th pixelrow
480th pixelrow
R:0.338G:0.367B:0.374
1.080
1.08
0
BGR BGR
BGR BGR
BGR BGR
BGR BGR
BGR BGR
BGR BGR
BGR BGR
BGR BGR
BGR BGR
BGR BGR
Display Dot Diagram
Product Specification of PDP Module
7. CONNECTORS and CONNECTIONSPower Input Connector
Pin No. Symbol
1
2
3
4
Vs
Vs
nc
GND
Pin No. Symbol
5
6
7
8
GND
Va
GND
+5V
Connector P3001 Pin Assignment
Module side connector : 1-1123723-8 (Header)Mating Connector : 1-1123722-8 (Housing)Connector Supplier : AMP
1-1123723-8 Pin numbers(Top View, viewed from the pin connection side)
12345678
Connector P2005 Pin Assignment
Module side connector : 1-1123723-10 (Header)Mating Connector : 1-1123722 –10 (Housing)Connector Supplier : AMP
1-1123723-10 Pin numbers(Top View, viewed from the pin connection side)
12345678910
Connector P2006 Pin Assignment
Module side connector : 1-1123723-4 (Header)Mating Connector : 1-1123722-4 (Housing)Connector Supplier : AMP
1-1123723-4 Pin numbers(Top View, viewed from the pin connection side)
Pin No. Symbol
1
2
5V
5V
Pin No. Symbol
3
4GND
GND 1234
Pin No. Symbol
1
2
3
4 nc
Pin No. Symbol
6
7
GND
GND5
8
VS
9
10
nc
GND
GND
nc
VS
VS
Product Specification of Power Supply Unit
8. Input/Output pin assignment & specification
Pin Assignment
1 2
8 7 6 5 4 3 2 1
10 9 8 7 6 5 4 3 2 1
4 3 2 1 12345678
123456789
123456789101112
1234
1234567
#1 : Vs#2 : Vs#3 : NC#4 : GND#5 : GND#6 : Va#7 : GND#8 : +5V
CN807CN806
#1 : Va#2 : Va#3 : GND#4 : GND#5 : GND#6 : GND#7 : NC#8 : Vs#9 : Vs#10 : Vs
#1 ~#2: 5Vctrl#3 ~ #4: GND
CN805CN808#1 ~ #4: +5Vctrl#5 ~ #8: GND
CN804
CN803
#1 ~ #3 : 5Vsc#4 ~ #6 : GND#7, #8 : 12Vsc#9, #10 : GND #11, #12 : NC
CN802 #1 ~#2: 30V or 24V #3 ~ #4: GND
CN801 #1 : ACD#2 : RLY ON#3 : 5Vst_by#4 : GND#5 : Vs ON#6 : 5VD#7 : NC
CN02 CN03CN01
Before connecting with S/W
From inlet
AMP171825-2CN809
AMP171825-8CN808
AMP1-1123723-8CN807
AMP1-1123723-0CN806
AMP1-1123723-4CN805
AMP171825-9CN804
AMP1-171825-2CN803
AMP171825-4CN802
AMP171825-7CN801
AMP3-176976-1(Natural)CN03
AMP3-176976-1(Natural)CN02
AMP3-176976-2(Red)CN01
VendorSpecificationLocation No.
Live
Neutral
Live
Neutral After connecting with S/W
CN8091
2
#1 : 9Vsc#2: GND
1 2
* PSU operation method S/W
Normal : On/Off with Vsc B/D
Auto : Automatic On/Off without Vsc B/D
Selection S/W
24V 30V
#1 : 9Vsc#2 : 9Vsc#3 : GND#4 : 5Vsc#5 : 5Vsc#6 : 5Vsc#7 : GND#8 : GND#9 : GND
1 2
1 2
Product Specification of Power Supply Unit
9. Adjustment detail
Adjustment detail
8 7 6 5 4 3 2 1
123456789
123456789101112
1234
1234567
CN807
CN804
CN803
CN802
CN801
CN8091
2
Selection S/W
24V 30V
1 2
* PSU driving method S/W
Normal(Mode1) : Driving with interface B/D
Auto(Mode2) : Driving without interface B/D
CN02 CN03
CN01
* Connect with Noisefilter Cable
Live
Neutral
Live
Neutral
1 2 1 2
1 2
* You can select output Audio Voltage(24V or 30V)
Vs adj.
Va adj.
* Vs Voltage Variabe Resistor- Turn right, increase VoltageTurn left, decrease Voltage
* Va Voltage Variabe Resistor- Turn right, increase VoltageTurn left, decrease Voltage
* Connect with S/W Cable
※ The color of CN01 is red.(The color of CN02, CN03 are natural.)
Selection S/W
Normal(Mode1)
Auto(Mode2)
* Connect with S/W Cable
12345678
CN80810 9 8 7 6 5 4 3 2 1
CN806CN8054 3 2 1
Product Specification of PDP Module
Y-SUS
E/X Tube
X right
CONTROLLERSignal Input
(R,G,B,H/Vsync.)X left
Z - SUS
3211QKE008A
Coner Plate
P/N(carved)
8. LABELLABEL Sticking Position
Identification Label : LABEL
①Model Name② Bar Code (Code 128, Contains the manufacture No.)③Manufacture No.④ The trade name of LG Electronics⑤Manufactured date (Year & Month)⑥Manufactured place
7.0
2.5⑦
①
②
③
④ ⑤ ⑥
Trouble Shooting Manual of PDP Module
- Introduction - Precautions - Basic - Trouble shooting
COMPOSITION OF PDP BOARDS
CONTROL B/D
Y-DRIVE
BOTTOM
Y-SUS
B/D
Y-DRIVE
TOP
X-LEFT B/DX-RIGHT B/D
Z-SUS B/D
COFCOF
IPMIPM
1. Introduction
PSU42” V6 MODEL.
Definitions
Exhaust hole
long 1
long 2short 1
short 2
COF long2-1 • • • • • • • • COF long 2-7
Definition of MODULE position
6####
2004.02402K242V6000266.ASLGA
Identification label
① Model Name② Bar Code (Code 128, Contains the manufacture No.)③ Manufacture No.④ The trade name of LG Electronics⑤ Manufactured date (Year & Month)⑥ The place Origin⑦ Model Suffix
①
②
③
④ ⑤ ⑥
⑦
1. Introduction
* Back side of module
Vsc-VyVsetup
Voltage label (Attached on back side of module)
Part No. label (Attached on board)
COF serial No. label (attached on COF)
1. Introduction
PCB PART NO.
BOARD ASS`Y PART NO.
BOARD NAME
BOARD SERIAL NO.
COF SERIAL NO.
8 /40
Terms of defect
Add short (line on)
Sus open (line off)
Sus short (line on)
Add open (line off)
AppearanceTerm
1. Introduction
9 /40
1. Before repairing there must be a preparation for 10 min.
2. Do not impress a voltage that higher than represented on the product.
3. Since PDP module uses high voltages, Be careful a electric shock
and after removing power some current remains in drive circuit.
so you can touch circuit after 1 min.
4. Drive circuits must be protected from static electricity.
5. The PDP module must be Moved by two man.
6. Be careful with short circuit of PDP boards when measuring any voltages.
2. Precaution
Be sure to read this before service. When using/ handling this PDP module, Please pay attention to the
below warning and cautions.
Safety precautions
Before request service
2. Check the model label. Whether it is boards of same model with label.
3. Before requesting Service, please inform us a detail defect phenomenon and history of module.
it can be helpful to us for a smooth sevice.
Ex) COF long 2-1 fail ,address 1 line open, Y b/d problem , mis-discharge.
1. Check panel surface and appearance of B/D.
SCRATCHING TEARING BEING PUSHED
BENDING CHOPING
2. Precaution
COF is the most important component in the PDP module.
Even a little imperfection of COF can make a serious screen problem.
Handle with care (COF)
X LEFT B/D X LEFT B/D X RIGHT B/D X RIGHT B/D
3. Basic
1. X B/D
<COF Separating>
: receiving LOGIC signal from CONTROL B/D and make ADDRESS
PULSE(generates Address discharge)by ON/OFF operation,
and supplies this waveform to COF(data) Power partSignal part
Lift up lock as shownin narrow.
Pull COF as shown in narrow.
12/40
: make SUSTAIN PULSE and ERASE PULSE that generates
SUSTAIN discharge in panel by receiving LOGIC signal from
CONTROL B/D.
this waveform is supplied to panel through FPC(Z).
*composed with IPM,FET,DIODE, electrolytic capacitor ,E/R coil.
* IPM (Intelligent Power Module)
E/R(Energy recovery)
Separate the fixed Screw of Z-Board.Pull out Lock as shown in arrow.
Condition in Lock part is pulled Pull FPC Connector as shown in arrow.
<FPC Separating>
2. Z sustain B/D
3. Basic
13/40
1) This is a path to supply SUSTAIN ,RESET waveform which made
from Y SUSTAIN B/D to panel through SCAN DRIVER IC.
2) Supply a wave form that select Horizontal electrode (Y SUSTAIN electrode)
sequentially.
- potential difference is 0V between GND and Vpp of DRIVER IC
in SUSTAIN period.
- being generated potential difference between GND and Vpp only
in SCAN period.
* In case of 42” V6 use DRIVER IC IC 8 EA (TOP, BOTTOM: each 4EA)
3. Y drive B/D
3. Basic
14/40
: generates SUSTAIN,RESET waveform, Vsc(SCAN)voltage.
and supplies it Y DRIVER B/D.
* Composed with IPM,DIODE, electrolytic capacitor ,FET.
: creates signal processing (Contour noise,reduction ISM,..)
and an order of many FET on/off of each DRIVER B/D with
R,G,B each 8bit input.
* Use 3.3V/5V 2 kinds of power .
5. Control Board
4. Y sustain B/D
3. Basic
15/40
: Being impressed 5V, Va ,Vs,
DC/DC converter makes
5V,Va,Vs,Vset_up,Vsc
which is essential for each B/D.
There is no DC/DC B/D in
model 40 〞 /42 〞(1 POWER B/D).
* 50 〞 60 〞embedded DC/DC B/D
separately because of high power
consumption.
DC/DC con. part6. DC/DC Converter part
3. Basic
16/40
: supply a driving waveform to PANEL by connecting a PAD electrode of PANEL with PCB(Y and Z).
* there is two type of this for Y B/D. One is single-sided,another is double-side. These are having pattern on it
* for Z B/D, there is no pattern , single-sided, and Betatype(all of copper surface).
: for connecting a Logic signal between B/D and B/D.*There is 0.5mm pitch,50pin type
1mm pitch ,30pin type.
7. FPC (Flexible Printed Circuit)
8. FFC (Flat Flexible Cable)
3. Basic
: supply a waveform which made from X B/D to panel and select
a output pin that is controlled by COF when be on or off.
96 output pin per IC.
the more the resolution higher, the less spare space where
can set IC on it in B/D. without using IC PACKAGE,
we can use a BARE IC , so we can get IC with LOW COST
because we do not solder IC on PCB directly,
a soldering defect rate decrease.
* composition
1) FPC + Heat /Sink
⇒ FPC for COF must have a Low Spec decline with getting damp
2) CHIP resistor + CHIP CAPACITOR
3) BARE IC (STV7610A/WAF) + GOLD WIRE/AL WIRE
4) EPOXY MOLDING
9. COF (Chip On Film)
Bare IC
* 42 V6 COF is the same as 42V5.
3. Basic
18/40
: composition
HEATSINK,CAPACITOR
DIODE
IC LINEAR
RESISTORTANSISTOR,FETS.
: description
Attached at Z B/D and Y B/D, make Sustain waveform.
Sustainer : supply a square wave to panel to make a video.
10. IPM(Intelligent Power Module)
IPM
3. Basic
19/40
4. Trouble shooting.
what kind of defect?Fast check up
Horizontal defect?
vertical defect?
Mis –dischargeon screen?
No display?
defectCheck model No. of module ,all connectors and cables.
Check panel appearance Check PSU output (Va,Vs,5v) Check Y, Z b/dinput voltage
Replace ctrl b/d Replace Y, Z b/d
Check panel appearance Check COF Replace ctrl b/dReplace X b/d
Check FPC Replace Y drv b/d Replace Y sus b/d Replace ctrl b/d
Replace Y drv b/d Replace Y sus b/d Replace ctrl b/d
20/40
what kind of defect?
4. Trouble shooting.
Horizontal defect?
vertical defect?
Mis –dischargeon screen?
No display?
Logical judgment
What kind of defect ?
Please follow the no display trouble shooting.
Bar defect appeared?
Line defect
Please follow the mis discharge trouble shooting.
Please follow bar defect trouble shooting.
Please follow the line defect trouble shooting.
21/40
Confirm every Connector (PSU, Y-SUS, CTRL, Z-SUS)
⇒ module may not be normal by mis-connection which can not send signal and power.
Also Mis connection for a long time has a specific b/d failed.
1. Connector
4. Trouble shooting.
No display
CTRL B/D + Y-SUS CTRL B/D + Z-SUS CTRL B/D + X-B/D Signal input(LVDS)
Check each section with following method if there is problem, replace or repair that part.
If not go to the next section.
22/40
Confirm exhausting Tip and find Crack with naked eyes to check vacuum state.
If there is problem replace the module .
⇒ in case of vacuum breakdown, module makes a shaking noise because of inside gas ventilation.
(there may be a small crack which could not see with naked eyes. And this noise is different from Capacitor noise. )
2. Exhaust tip Crack
CRACKEDNORMAL
4. Trouble shooting.
1. Check each unit part of PSU inside with naked eyes.
(capacitor, FET, a kind of IC, resistor)
2. Check FUSE and SW1 (on Normal).
3. Check Output voltage which is converted from AC V
to DC V.
voltage Check (5V, Va, Vs)
※When PSU Protection occurred. Check Short
between Y-SUS, Z-SUS B/D .
3. PSU(Power Supply Unit)
Fuse open check
SW1 Normal
Multi-meter Touch point(5V, Va ,Vs must accord with Module Label)
Vs Voltage ADJ(Vs : About 180 ~195 V)
Va, 5V(VCC) Voltage ADJ Va : About 55 ~65 V 5V(VCC) : 5V~5.5V)
4. Trouble shooting.
if not sameConfirm
input voltage
Adjust
voltages
1. Confirm LED D17(flashing) ,13 lighting
2. If not CHECK OSC X1 output.
3. Check CTRL input voltage
(CONNECTOR P300)
4. CHECK 3.3V, 5V,15V.
5. Check IC 11 3.3V
IC 3 2.5V
4. Ctrl B/D
4. Trouble shooting.
Check oscillating state.
(normal 100 MHZ)
Be careful with physical shock.
Probe
Touching
point
Input voltage
Diode
OSC(X1)
Check IC 11,13
DMM +
DMM – (GND)
25/40
5. Y-sus B/D1. Check FUSE [FS1(5v) ,FS2(Vs)].
2. Check voltages(Vsetup,-Vy, Vscw)
3. Check DIODE between GND and Y SUS output.
[SUSUP(OC2) SUSDN(OC1)].
forward=0.4 ,reverse=OVERLOAD.
4. Check whether output voltages agrees
with voltage that represented in label.
Vsetupsetdn
-Vy
Vscw
setup
4. Trouble shooting.
FS2
FS1
Normal diode value = OL (reverse)Normal diode value= 0.4 (forward)
Check whether output voltages agrees with voltage that represented in label.
4. Trouble shooting.
Check diode value GND between Y-SUS output.
6. Z-sus B/D
Va FUSE 6.3A Vs FUSE 2A or 4A
5V FUSE
1. Check the FUSE.
2. Check input voltages.(Va, 5V,15V)
3. Check FPC out put diode value.
4. Check ramp waveform.
4. Trouble shooting.
Check the FUSE Check input voltages
caution: check certainly after removing FPC.
Normal diode value=OVER LOAD(reverse)
Check FPC output diode value.
Normal diode value=0.375(forward)
Variable resistance of Z RAMP
waveform slope.
4. Trouble shooting.
29/40
4. Trouble shooting. Power protection
It is power protection when power is off automatically within 2~3 min. from power on.
Power protection function protect the boards when occurred short on circuits of PDP module or power problem.
If can not impress power even after replacing PSU, find out where the short occurred.
UNICON PSUDAEGIL PSU
* PSU makers.
30/40
4. Trouble shooting.
Vertical defect (bar)
1. ConnectorCheck COF connector.
If not connected well,it will Make a bar defect .
BarCheck here
2. Checking COFConfirm whether COF was torn. And then check input of COF resistor and IC.
TearingCOF 6 is torn partly
Check here Off
Check each section with following method if there is problem, replace or repair that part.
If not go to the next section.
31/40
Checking address COF input of resistor and IC
4. Trouble shooting.
COF resistor checking
Check the both side of resistor With Digital multi meter(DMM) .
If the resistor is normal, the resistor value will be 10.2 ~ 10.8 Ω
But if not, the value will be 0 or infinity and replace the resistor.
DMM( + terminal)
DMM(- terminal)
DMM (- terminal)
` DMM (+ terminal)
IC input checking
Inside of IC , there is 4 ea diodes which separated in 2 series .
(input 2, output 2)
*how to check
1.contact DMM - terminal to a right terminal of condenser(GND)
and DMM + terminal to a right terminal of IC, normal value 0.66 (fig.1)
2.contact DMM - terminal to Output terminal of resistor, and
DMM + terminal to a right terminal of IC , normal value 0.73 (fig.2)
Fig. 1 Fig. 2
4. Trouble shooting. Checking address COF input of resistor and IC
Buffer IC
MCM
COF IC1 COF IC2 COF IC3 COF IC4
각각 16 line
Array저항
96 output
A flow of address signalIn this figure, we can easily suppose
what will be appeared on screen when a specific part failed.
<Diagram of ctrl b/d>
3. Ctrl B/DCTRL B/D supplies video signal to COF. So if there is a bar defect on screen,
It may be the ctrl b/d problem.
4. Trouble shooting.
Vertical defect (line)
This phenomenon is due to COF IC inside short or adherence part of the Film and rear panel electrode problem. In this case, replace the panel.
4. Trouble shooting.
This is MCM of Ctrl b/d defect. MCM can not be replaced separately. So replace the ctrl b/d.
1 line open or short
Line open or short with same distance.
MCM (Multi Chip Module)
1 line open
In case of 1 line open or short , check foreign substances in COF connector.
First blow up foreign substances with your mouth. And then if the same line appears, replace the panel.
1 electrode open
/40
• Case 1: Buffer IC fail
COF IC 1,2 ⇒ 192 line(96+96) open.
COF IC 3,4 ⇒ 64 line open (with fixed interval there is on,off ……. Repetition)
• case 2 : Array resistor fail
COF IC1 ⇒ 16 line , COF IC2 ⇒ 16 line open
• case3 : COF IC fail
96 line open.
line defect from each parts
4. Trouble shooting.
96 line open
16 line open
Horizontal (bar)
4. Trouble shooting.
1. ConnectorIt can make a horizontal bar that connector on Y b/d and Z b/d did not plugged well. Because sustain voltage
can not be supplied to panel. So check connectors (FPC, Y drv –Y drv) first.
Most horizontal defects can be repaired. In case of adherence part of the Film and rear panel
electrode defect or panel electrode open,short , replace the panel.
Disconnected
Disconnected Screen off
Horizontal bar
37/40
Normal diode value. (in case of Panasonic IC=1.035)
* It can be different from each IC Maker. (in case of TI IC= 0.6~0.7)
Defect diode value= 0.018
Check diode value of the right side part of output pin.
2. Scan IC check
4. Trouble shooting.
Check here with DMM(either forward or reverse is ok)DMM + DMM -
38/40
4. Trouble shooting.
Horizontal (line)
1. Check FPCIn case of horizontal 1 or more line, it is due to FPC or panel inside .
ctrl b/d, Y b/d is just normal.
2. Check scan ICCheck with same method that presented in Horizontal (bar).
FPC electrode open
Panel electrode
Insulation break downHorizontal 1 line.
40/40
Forward : test 1 GND(+) , Sus-out(-) 2 Sus-out(+),Vs(-)3 ER-DN(-),ER-COM(+)4 ER-COM(-),ER-UP(+)
when each 4 TEST Diode value is over 0.4V => OK
Reverse : test 1 GND(-) , Sus-out(+) 2 Sus-out(-),Vs(+)3 ER-DN(+),ER-COM(-)4 ER-COM(+),ER-UP(-)
when each 4 nodes TEST Diode value is infinity => OK
※ Specially, the value of ER-UP,COM,DN in the Y/Z board, should be
checked all of them. but, the terminal of Vs,Sus-out,GND,
we must aware to know after check one of IPM because it is parallel.
if no problems, check 15V(Y,Z B/D) with GND, Forward value 0.3V,
Reverse value infinite. If no problems,
4. Trouble shooting.
How to check IPM
BOM Summry Report with Cost ( Report For PDP4206EM ) QuantityItem Component Description/Country Origin Unit
Summary一. ElEC Parts
1 E3403-004001 TUBE SUMITUBE D5.0 BLK 600V M 0.32 E3421-926004 WIRE ASSY 1H2.5-2H2.5 L270 12P/2+ PCS 13 E3421-926006 WIRE ASSY TJC3-4Y/AMP-4Y/210 FOR S PCS 14 E3421-926007 WIRE ASSY 1H2.5-2H2.5 L330 31P (LV PCS 15 E4406-068001 FILTER EMI CTRC-0930-1B FOR 42 PCS 36 E4406-069001 FILTER EMI CTNF-100B FOR 4 PCS 17 E4850-003001 SPEAKER SUB(FOR 42TD1) 16 OHM PCS 18 E4850-004001 SPEAKER SUB (FOR 42TD1) 16 OHM PCS 19 E6205-001003 DISPLAY PDP LG-V6 42" WITH FI PCS 110 771-42D103-01 REMOTE RECEIVE PCB ASSY PCS 1
11 771-42D102-01 SPK JACK PCB ASSY PCS 1
12 771-42D101-01 KEY PCB ASSY PCS 1
13 774P42D101-01 POWER ASSY PDP42 PCS 114 771E42D101-01 Main PCB Sect 1
15 771L42D101-05 AUDIO PCB ASSY (LG/V6) W/O TUNER FOR USA Sect 1
二. Mech Parts1 200-42D121-21A FRONT CABINET BLACK ENG 42TD1 W/O TV PCS 12 244-34B801-01 GIFT BOX HANDLE 34B8 PCS 23 248-46D201-01 HANDLE FOR PLASMA PCS 24 263-42D101-01S POWER LENS 42D1 PCS 15 269-42D101-01L REMOTE LENS 42D1 PCS 16 326-050010-40 SPONGE CUSHION 500X10X4.0MM W/ADHESI PCS 27 326-095010-40 SPONGE CUSHION 950X10X4.0MM W/ADHESI PCS 28 361-101261-01 CABLE TIE PCS 289 367-42D101-01 EDGE SADDLE 14MM 42D1 PCS 410 367-42D102-01 EDGE SADDLE 27MM 42D1 PCS 211 384-42D101-03 TUNER BOARD PLATE ENG 42TD1 W/O RF PCS 112 384-42D102-01 PVC SHEET FOR MAIN BOARD 42D1 PCS 113 387-42D101-06H MODEL PLATE AKAI ENG 42TD1(JIAYING) PCS 114 388-42D102-01 PC SHEET FOR REMOTE PCB42D1 94V0 0.3 PCS 115 388-42D103-01H CAUTION PLATE ENG 42D1 H PCS 116 388-42SB02-01H SPK PLATE MAIN SANSUI 42" 42SB PCS 117 388-42SB04-01H POWER PLATE SANSUI 42SB PCS 118 402-42D112-01 BACK COVER FOR V6 42D1 PCS 119 423-42D107-01 PANEL PATCH V6 42D1 PCS 420 423-42D108-01 PATCH FOR SHIELD BOX 42D1 PCS 121 423-42D10C-01 SUPPORT FOR PW BKT 42D1 PCS 122 423-42D10F-01 CONNECT SHEET 42D1 PCS 223 423-42D113-01 FILTER SUPPORT TOP 42D1 PCS 124 423-42D114-01 MAIN BKT FOR V6 42D1 PCS 225 423-42D115-01 POWER BKT FOR V5/V6 42D1 PCS 1
26 423-42D122-01 FILTER SUPPORT L&R 42D1 PCS 227 423-42SD21-01S FILTER SUPPORT BOTTOM 42SD PCS 128 430-42D101-01 HEATSINK FOR AUDIO IC 42D1 PCS 129 436-42D105-01 TERMINAL SHEET W/O RF HOLE PCS 130 457-42D101-01 CLAMP ID=4.3MM L=46MM PCS 731 481-42D111-01 SHIELD BOX FOR MAIN PCB JIAYING PCS 132 481-42D112-01 SHIELD BOX FOR TUNER PCB JIAYING PCS 133 483-42D101-01 SHIELD COVER A 42D1 PCS 134 483-42D102-01 SHIELD COVER B 42D1 PCS 135 512-42D101-01 SHEET 1160X1160 42D1 PCS 0.285736 512-42D102-01 SHEET 1160X1480 42D1 PCS 0.285737 553-002007-40A SHIELD GASKET 20X7X4.0MM W/CONDUCTIV PCS 438 553-002509-25A SHIELD GASKET 25X9X2.5MM W/CONDUCTIV PCS 239 553-004009-40A SHIELD GASKET 40X9X4.0MM W/CONDUCTIV PCS 140 553-005009-25A SHIELD GASKET 50X9X2.5MM W/CONDUCTIV PCS 141 553-012509-40A SHIELD GASKET 125X9X4.0MM W/CONDUCTI PCS 1142 553-017009-25A SHIELD GASKET 170X9X2.5 PCS 243 553-020009-40A SHIELD GASKET 200X9X4.0MM W/CONDUCTI PCS 444 553-024509-40A SHIELD GASKET 245X9X4.0MM W/CONDUCTI PCS 245 553-056009-40A SHIELD GASKET 560X9X4.0 W/CONDUCTIVE PCS 246 553-095009-40A SHIELD GASKET 950X9X4.0 W/CONDUCTIVE PCS 247 554-080030-01 SHIELD CLOTH 80X30MM W/CONDUCTIVE AD PCS 2.548 563-119- SERIAL NO. LABEL PCS 149 568-P46T02-02 WARNING LB ENG 42SF NIL PCS 150 579-42D102-09 SERIAL NO/BAR CODE LABEL 42D1 PCS 151 579-42D102-14 BAR CODE LABEL AKAI PD4206EM(USA) PCS 252 579-42D103-02 ON/OFF LB ENG 42D1 NIL PCS 153 579-42D105-01 PROTECTIVE EARTH LABEL FOR ESA 42TD1 PCS 154 590-42D101-06 WARRANTY CARD AKAI PDP4206EM(USA) PCS 155 600-305008-00 MACH.SCREW PAN 3X8 BZN + PCS 256 601-305008-00 MACH.SCREW CTS 3X8 BZN + PCS 257 602-305006-10 MACH.SCREW WHR 3X6 NIP + PCS 1758 604-305005-30 MACH.SCREW BID 3X5 BNI + PCS 2259 604-601020-00 MACHINE SCREW BINDING M6X1.0PX20MM B PCS 660 60D-407010-40 MACH. SCREW W/SPRING WASHER M4.0X0.7 PCS 2161 610-300210-00 S-TAP.SCREW RND 3X10 A BZN + PCS 262 612-300210-00 S-TAP.SCREW WHR 3X10 A BZN + PCS 763 614-260208-10 S-TAP.SCREW BID 2.6X8 A NIP + PCS 264 614-400408-10 S-TAP.SCREW BID 4X8 D NIP + PCS 265 614-400412-00 S-TAP.SCREW BID 4X12 T BZN + PCS 3466 615-400214-00 SELF-TAPPING SCREW W/BIG WASHER PCS 167 619-300210-10 SPECIAL SCREW 3X10 NP "+" PCS 2368 900-42D103-01 PANEL DISPLAY FILTER OPTIMAX PCS 1
三. Packing1 300-42D111-02C POLYFOAM FOR MAIN UNIT 42D1 TOP PCS 12 300-42D112-02C POLYFOAM FOR MAIN UNIT 42D1 BOTTOM PCS 13 310-504004-01 POLYBAG EPF 50"X40"X0.04 PCS 1
4 510-42D104-01K GIFT BOX AKAI 1154(W)X320(D)X1032(H) PCS 15 511-42D101-01K CARTON BOX FOR BTM 42D1 PCS 1
四. ACCESSORY1 511-42D102-01A ACCESSORY BOX PCS 12 790-003603-A9 AKAI Remote 0036 for PDP4206EM PCS 1
3 580-42D101-11 INSTRUCTION BOOKLET E FOR AKAI PDP42 PCS 14 310-111404-07V POLYBAG 11"X14"X0.04 PCS 15 E3404-157001 AC CORD UL 1.88M MET-4D7+SJT 16AWG/ PCS 16 E7301-010002 BATTERY AAA R03P1.5V <2> PCS 27 734-BM0305-01 SECC STAND BASE 42" B/G BOX W/O POLY SET 1
Exploded View
56 614-400412-00 SCREW 4x12 155 615-400412-00 SCREW 4x14 154 423-42D10C-01 SUPPORT FOR PW BKT 153 423-42D108-01 PATCH FOR SHIELD BOX 152 367-42D102-01 EDGE SADDLE 27MM 251 604-601020-00 MACH.SCREW M6x20 450 248-P46U02-01 HANDLE 249 622-302408-10 STP SCREW 3x8 248 23845857 CLAMP 447 560-42D101-01 MODEL PLATE 146 384-42D102-01 PVC SHEET FOR TUNER BOARD 145 384-42D101-01 PVC SHEET FOR MAIN BOARD 144 402-42D10X-01 VACK COVER 143 483-42D102-01 SHIELD COVER B 142 602-305006-10 MACH. SCREW 3x6 1441 E7801-043004 TUNER BOARD 140 612-300210-00 STP SCREW 3x10 739 604-305005-630 MACH. SCREW 3x5 2238 436-42D101-01 BAK TERMINAL SHEET 137 481-42D102-01 SHIELD BOX B 13635 483-42D101-01 SHIELD COVER A 134 E7801-043006 MAIN BOARD 133 367-42D101-01 EDGE SADDLE 14MM 432 481-42D101-01 SHIELD BOX A 131 614-300210-00 STP SCREW 3x10 230 423-42D115-01 POWER BKT FOR V5/V6 129 E4405-035001 AC LINE FILTER 128 601-306008-10 MACH. SCREW 3x8 227 E4101-027001 POWER SWITCH 126 771-42D102-01 AV JACK PCB 125 423-42D114-01 MAIN BKT FOR V6/FORMOSA 224 423-42D107-01 PANEL PATCH FOR V6 423 60D-407010-10 MACH. SCREW W/SP WASHER 4x10 2022 E4850-002001 SPK BOX 121 614-400416-00 STP SCREW 4x16 3320 E6205-001003 PLASMAS PANEL 119 322-501004-01 CUSHION 500x10x4MM 218 322-951004-01 CUSHION 950x10x4MM 217 610-300210-10 STP SCREW 3x10 2216 423-42D101-01 FILTER SUPPORT BTM 115 423-42D102-01 FILTER SUPPORT L&R 214 423-42D103-01 FILTER SUPPORT TOP 113 559-500925-01 SHIELD GASKET 500x9x2.5MM 212 559-950925-01 SHIELD GASKET 950x9x2.5MM 211 900-42D101-01 DISPLAY FILTER LG 110 614-400480-10 STP SCREW 4x8 29 277-42D101-XXS FUNCTION KNOG 58 771-42D101-01 KEY PCB 17 388-42D101-01 PC SHEET FOR KEY PCB 16 614-260208-10 STP SCREW 2.6x8 55 388-42D102-01 PC SHEET FOR REMOTE PCB 14 771-42D103-01 REMOTE PCB 13 269-42D101-01L REMOTE LENS 12 263-42D101-01S POWER LEN 11 200-42D101-XXS FRONT CABINET 1
ITEM PART NO. DESCRIPTION QTY REMARK
No. Pin name1 No connection2 RXD (Receive data)3 TXD (Transmit data)4 DTR (DTE side ready)5 GND6 DSR (DCE side ready)7 RTS (Ready to send)8 CTS (Clear to send)9 No Connection
1
5
6
9
2354678
RXDTXDGNDDTRDSRRTSCTS
TXDRXDGNDDSRDTRCTSRTS
PC
7-wire configuration(Standard RS-232C cable)
D-Sub 9
3256487
PDP
D-Sub 9
2354678
RXDTXDGNDDTRDSRRTSCTS
TXDRXDGNDDTRDSRRTSCTS
PC
3-wire configuration(Not standard)
D-Sub 9
3254678
PDP
D-Sub 9
Software upgrade- Connect the RS-232C input jack to an external control device (such as a computer) and software upgrade.
Type of connector; D-Sub 9-pin male
RS-232C configurations
If you forget your V-Chip Password - Omnipotence V-Chip Password: 363200. - Press MENU Right button. - Press CH+, CH- or Up, Down buttons to highlight "CC-VChip" Control. - Press MENU Right and Up, Down buttons to highlight "Change Blocking Password". - Press Right button to pop up "Old Password". - Use the Number buttons (0~9) to enter an omnipotence Password. - Press Right button to confirm and will pop up "Password Change Successful". - Suggest: Change to your familiar Password again.
Software upgrade Process
- Power Switch OFF. - Connect the RS-232 jack of the computer to the RS-232 jack on the plasma back panel.
RS-232C connection cables are not supplied with the Plasma.
ComputerRS-232
PDPRS-232
- Power Switch ON. The power indicator on the front of the panel should now display red, that thePlasma is in standby mode.
- Copy the software (Flash Upgrader) to the computer. - Open the software (Flash Upgrader.exe)
- Point "Flash" on the interface of the Flash Upgrader.exe.
Flash
- Press STANDBY button on the front panel or POWER button of Remote control, Power indicator isgreen, the Plasma is in power ON mode, software start upgrader immediately.
- After the Hard Reset is finished, shut down the power switch, take out the RS-232C connection cablesafter the power indicator is extinguished.
Note: The computer and plasma must be keep Power ON in the software upgrade processing.If the function is abnormal, software upgrade again.
- Hard Reset after the upgrader is finished.Method: 1. Power Switch Off
2. Power Switch On again3. Sequence press F.WHITE, VIDEO, I.P.C. button on the Remote control enter factory Menu
select "Misc.", "Hard Reset", press Menu Right button to Hard Reset is finished.4. If the color of picture is abnormal, Hard Reset again.
Misc. Hard Reset