service manual hl32xxb pal v1 0

HL-32XXB LCD TV MONITOR

(1/72) HL-32XXB SERVICE MANUAL HRD 2004-07

32-Inch LCD TV

Model (PAL) : HL-32XXB

Version : 1.0 Jan.7th. 2004

Service Manual



Rev. Date Description Page No

1.0 Jan,7.05

Revision History



Important Safety Instructions

Always be careful when using your TV. To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind when installing, using, and maintaining your machine.

- TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK HAZARD. - DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.- SHOCK HAZARD DO NOT OPEN.

CAUTION

WARNING- Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

- This is Class B product. In a domestic environment this product may cause radio interference in which case theuser may be required to take adequate measures.

- To reduce the risk of fire and electric shock, do not expose this product to rain or moisture.

FCC NOTICEThis device has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in home environment as well as in a commercial, industrial or business environment. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.

Changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Connecting of peripherals requires the use of grounded shielded signal cables.

Read all safety and operating instructions before operating your TV.

Keep the safety and operating instructions for future reference.

Heed all warnings on the TV and in the operating instructions.

CAUTIONThese servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operatinginstructions unless you are qualified to do so.

CAUTIONThe stand intended for use only with This LCD TV. Use with otherapparatus which might result in Instability causing possible injury .



Always be careful when using your LCD TV. To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind when installing, using, and maintaining your machine. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other , grounding type plug has two blades or a third grounding prong is required. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

the point where they exit from the apparatus. 11) Only use the attachments/accessories specified by the manufacturer. 12) Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.



Follow all operating and use instructions.

Unplug the TV from the wall outlet before cleaning. Use a damp cloth; do not use liquid or aerosol cleaners.

Never add any attachments and/or equipment without approval of the manufacturer. Such additions can increase the risk of fire, electric shock, or other personal injury.

Do not use the TV where contact with or immersion in water is a possibility, such as near bath tubs, sinks, washing machines, swimming pools, etc.

When installing the TV on a table, be careful not to place the edge of its stand.

- This may cause the TV to fall, causing serious injury to a child or adult, and serious damage to the TV.




Provide ventilation for the TV. The unit is designed with slots in the cabinet for ventilation to protect it from overheating. Do not block these openings with any object, and do not place the TV on a bed, sofa, rug or other similar surface. Do not place it near a radiator or heat register. If you place the TV on a rack or bookcase, ensure that there is adequate ventilation and that you've followed the manufacturer's instructions for mounting.

Use only the accessory cord designed for this product to prevent shock. The power supply voltage rating of this product is AC100-240V, the power cord attached conforms to the following power supply voltage. Use only the power cord designated by our dealer to ensure Safety and EMC. When it is used by other power supply voltage, power cable must be changed. Consult your product dealer.

Use only a grounded or polarized outlet. For your safety, this TV is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still does not fit, contact your electrician to replace your outlet.

Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. When installing an outside antenna system, be extremely careful to keep from touching the power lines or circuits. Contact with such lines can be fatal.

Unplug the TV from the wall outlet and disconnect the antenna or cable system during a lightning storm or when left unattended and unused for long periods of time. This will prevent damage to the unit due to lightning and power-line surges.

Protect the power cord. Power supply cords should be routed so that they won't be walked on or pinched byobjects placed on or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit.




Follow all operating and use instructions.

Unplug the TV from the wall outlet before cleaning. Use a damp cloth; do not use liquid or aerosol cleaners.

Never add any attachments and/or equipment without approval of the manufacturer. Such additions can increase the risk of fire, electric shock, or other personal injury.

Do not use the TV where contact with or immersion in water is a possibility, such as near bath tubs, sinks, washing machines, swimming pools, etc.

When installing the TV on a table, be careful not to place the edge of its stand.

- This may cause the TV to fall, causing serious injury to a child or adult, and serious damage to the TV.


Do not overload the wall outlet orextension cords. Overloading canresult in fire or electric shock.

Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts. Never spill liquid of any kind on the TV.

Bend antenna cable between inside and outside building to prevent rain from flowing in.

-This may cause water damagedinside the TV and could give an electric shock.

Ground outdoor antennas. If an outside antenna or cable system is connected to the TV, be sure theantenna or cable system is grounded so as to provide some protection against voltage surges and built-upstatic charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984, provides informationabout proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antennadischarge unit, size of grounding conductors, location of antenna discharge unit, connection to groundingelectrodes, and requirements for the grounding electrode.

Do not place an outside antenna inthe vicinity of overhead power lines,other electric light or power circuits.- This may cause an electric shock.

There should be enough distancebetween an outside antenna andpower lines to keep the former fromtouching the latter even when theantenna falls.- This may cause an electric shock.

Do not attempt to service the TV yourself. Refer all servicing to qualified servicepersonnel. Unplug the unit from the wall outlet and refer servicing to qualified servicepersonnel under the following conditions:• when the power-supply cord or plug is damaged• if liquid has been spilled on the unit or if objects have fallen into the unit• if the TV has been exposed to rain or water• if the TV does not operate normally by following the operating instructions• if the TV has been dropped or the cabinet has been damaged• when the TV exhibits a distinct change in performance




When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in additional damage to the unit.

Upon completion of any service orrepairs to this TV, ask theservice technician to perform safetychecks to determine that the TV is in a safe operating condition.

If you make adjustments yourself,adjust only those controls that arecovered by the operating instructions.Adjusting other controls may result indamage and will often requireextensive work by a qualifiedtechnician to restore the TV tonormal.

Only use the specified batteries.-This make cause damaged theTV or could give an electricshock.

Do not place anything containingliquid on top of the TV.- This may cause a fire or could give an electric shock.

In case of smoke or strange smellfrom the TV, switch it off, unplugit from the wall outlet and contactyour dealer or service center.- This may cause a fire or could give an electric shock.

The distance between eyes and thescreen should be about 5~7 times aslong as diagonal length of the screen.- If not, eyes will strain.

When moving the TV assembled with speakers do not carry holding the speakers.-This may cause the TV to fall,causing serious injury to a child oradult, and serious damage to theTV.

Avoid having a fixed image remainon the screen for a long period oftime. Typically a frozen still picturefrom a VCR, 4:3 picture format or if a CH label is present; the fixedimage may remain visible on thescreen.




CONTENTS 1. INTRODUCTION -----------------------------------------------------------------------------------------------------------12

1.1 MODEL NAME

1.2 CERTIFICATION

1.3 WARRANTY

2. SPECIFICATION -----------------------------------------------------------------------------------------------------------12

2.1 FUNCTION AND DISPLAY SPECIFICATION

2.2 MISCELLANEOURS

2.3 CONNECTIVITY

2.4 ACCESSORY

2.5 DIMENSION/WEIGHT

3. ELECTRICAL SPECIFICATION ----------------------------------------------------------------------------------------14

3.1 I/O SIGNAL

3.1.1 SIGNAL TYPE

3.1.2 SIGNAL RATING

3.1.3 SOUND PRESSURE LEVEL SPECIFICATION

3.2 POWER

4. DISPLAY CHARACTERISTICS ----------------------------------------------------------------------------------------16

4.1 LCD Panel

4.1.1 DISPLAY PERFORMANCE

4.1.2 BACK-LIGHT UNIT

5. FUNCTION ----------------------------------------------------------------------------------------------------------------19

5.1 EXTERNAL CONTROL

5.1.1 FRONT KEY(OSD) CONTROL

5.1.2 REMOTE CONTROL AND KEY FUNCTION

5.2 OSD MENU ADJUSTMENT ITEM

5.2.1 TV/VIDEO/DTV MODE

5.2.2 RGB MODE

5.3 MAIN/SUB CONNECTOR

5.4 INPUT/OUTPUT CONNECTOR

5.4.1 RS232C INPUT TERMINAL

5.4.2 AUDIO INPUT TERMIANL

5.4.3 PC (RGB) OR DTV INPUT TERMINAL

5.4.4 S-VIDEO INPUT TERMINAL

5.4.5 COMPONENT(Y, Pb/Cb, Pr/Cr) INPUT TERMINAL

5.4.6 TV ANTENNA TERMINAL (EURO RF CONNECTOR)

5.4.7 MONITOR OUT TERMINAL

5.4.8 COMPOSITE INPUT TERMINAL

5.4.9 SPEAKER OUTPUT TERMINAL

5.4.10 AC POWER INPUT TERMINAL



5.4.11 DVI (DIGITAL) TERMINAL

5.4.12 SCART1,2 INPUT or OUTPUT TERMINAL(21PIN)

6. MECHANICAL SPECIFICATION ------------------------------------------------- --------------------------------------------31

6.1 DIMENSION

6.2 I/D LABEL

6.3 PACKING

6.4 WEIGHT

6.5 ACCESSORIES

6.5.1 RF CABLE

6.5.2 POWER CODE

6.6 OPTIONAL

6.6.1 EXTERNAL SPEAKER

6.6.2 TABLE STAND

6.6.3 WALL MOUNT BRACKET

7. ENVIRONMENT TEST ----------------------------------------------------------------------------------------------------------32

7.1 TEMPERATURE, RELATIVE HUMIDITY AND ALTITUDE

7.2 RANDOM VIBRATION TEST (PACKAGING)

7.3 DROP TEST (PACKAGING)

8. LCD MODULE CRITERIA -----------------------------------------------------------------------------------------------------33

8.1 LCD MODULE CELL DEFECT SPECIFICATION

8.1.1 DEFINITION

8.1.2 MEASURING AREA

8.1.3 CELL DEFECT SPECIFICATION

9. TIMING CHART -------------------------------------------------------------------------------------------------------------------34

9.1 ANALOG R, G, B TIMING

9.2 DTV TIMING

10. FIRMWARE DOWNLOAD CHART -----------------------------------------------------------------------------------------35

10.1 FIRMWARE UPGRADE INSTRUCTION GUIDE

10.1.2 PORT SETUP

10.1.3 LOAD

10.1.4 DOWNLOAD

10.1.5. AFTER DOWNLOAND, YOU CAN SEE “Wait Initialize” MESSAGE

11. RS-232C COMMAND LIST -----------------------------------------------------------------------------------------------------39

12. REMOTE CONTROL IR CODE VALUE -------------------------------------------------------------------------------------44

12.1 REMOTE CONTROL IR CODE VALUE

12.2 DISCRETE CODE VALUE

13. TROUBLE SHOOTING-----------------------------------------------------------------------------------------------------------45

13.1 THE LED LIGHTING STATUS OF OPERATION

13.2 TROUBLE SHOOT FLOW CHART

14. BLOCK DIAGRAM ----------------------------------------------------------------------------------------------------------------54

15. EXPLODED VIEW ----------------------------------------------------------------------------------------------------------------55



16. DISASSEMBLE PROCESS------------------------------------------------------------------------------------------------------56

17. DISASSEMBLE OF LCD MODULE--------------------------------------------------------------------------------------------63

18. BOM ---------------------------------------------------------------------------------------------------------------------------------- 66

APEENDIX – 1: DIMENSIONAL DRAWING

APPENDIX – 2: PACKING MANUAL

APPENDIX – 3: CARTON BOX DRAWING

APPENDIX – 4: NTSC RF CABLE

APPENDIX – 5: POWER CODE

APPENDIX – 6: EXTERNAL SPEAKER DRAWING

APPENDIX – 7: EXTERNAL SPEAKER PACKING METHOD

APPENDIX – 8: TABLE STAND DRAWING

APPENDIX – 9: TABLE STAND PACKING METHOD

APPENDIX – 10: WALL MOUNT BRACKET DRAWING

APPENDIX – 11: WALL MOUNT BRACKET PACKING METHOD

APPENDIX – 12: I/D LABEL



1. Introduction This is 32” LCD TV is designed by Harsper. This monitor shall be used for TV. This monitor has many kinds of I/O ports. It is PC, DVI, RF (TV), SCART1, SCART2, S-Video/AV, Component1 andComponent2 Port. This monitor displays 32inch wide screen (16:9) image and with built in audio amplifier. 1.1 Model Name: HL-3210B 1.2 Certificate of Standard

Item EMI (CLASS-B) Safety

Standard CE, FCC EN55013,20,22,24,EN61000

CB, NRTL EN60065,IEC 60065

1.3. Warranty

Harsper Warrants the products against in materials or workmanship under normal usage conditions For one calendar year from the shipping date.

2. Specification 2.1 Function and Display Specification LCD panel

Type no. 31.51 inches(800.4mm) diagonal Interface LVDS (single pixel) Size & Aspect ratio 32” (16:9) Max. Color 16.77million Resolution 1366X768(Wide XGA) Contrast Ratio 600:1 (Typical) Brightness 500cd/ (Typical)

TV standard & Setup TV System PAL(B/G,I,D/K) SECAM (B/G,D/K,L,L’) Tuning system VS Tuning

Program memory 99 channels

Picture

Picture control Brightness / Contrast / Color / Sharpness Aspect ratio 16:9, Panorama, Zoom1, Zoom2, 4:3 Color temperature Selectable 5 Mode (Cool 1, 2 Normal Warm1,2)

Audio

Sound system A2, NICAM Stereo Sound control News/ Standard / Music/ Movie/ User (Equalizer)

Video Advanced motion digital / Motion-Adaptive De-interlace process, Digital progressive line scaling

Input compatible Multiple input compatible HDTV Input 480i/P(60Hz), 576i/P (50Hz), 720P(50,60Hz), 1080i (50,60Hz), HDCP



Other Features

PIP/POP Advanced multi-windows viewing PIP / POP with four selectable window positions on Video mode

OSD language English, French, Spanish, Germany, Italy, China TTX Yes [Teletext UK/PDC/VPS], TOP, FLOF Auto Power off Yes Sleep Timer Yes Clock Yes, (Select On/OFF Time, On PR, On Volume) Programming Favorite channel programming, Digest

2.2 Miscellaneous Item Specification

Audio Built-in amplifier and two speaker(7Watt/Typ.) systems(optional)

External Control Front OSD Key Control, Remote control, RS232C Control 2.3 Connectivity Item Specification

TV Input RF/CATV (PAL/SECAM)

Scat1 Input SCART 21Pin X 1Port (Half Scart, Monitor Output) Scart2 Input SCART 21Pin X 1Port (Full RGB Scart, TV Output)

S-Video Input Mini Din 4Pin X 1Port Composite Input (AV) RCA X 1Port (AV Input) Audio Input (S-video/AV) RCA X 1Port Stereo R/L (Audio Input of S-video /AV 3 )

Composite Output (AV) RCA X 1Port (AV Output: Monitor Output) Audio Output RCA X 1Port Stereo R/L (Audio Output Of AV Output)

Component1 Input RCA X 1Port (Y, Pb/Cb, Pr/Cr : 480i/P, 576i/P 720P, 1080i) Audio Input RCA X 1Port Stereo R/L ( Audio Input of Component 1)

Component2 Input RCA X 1Port (Y, Pb/Cb, Pr/Cr : 480i/P, 576i/P 720P, 1080i) Audio Input RCA X 1Port Stereo R/L ( Audio Input of Component 2)

PC Input Mini D-Sub 15Pin X 1Port / HDTV Input(480P, 576P 720P, 1080i) DVI (DVI-D)Input Mini D-Sub 29Pin X 1Port / HDTV Input(480P, 576P 720P, 1080i) Audio Input RCA X 1Port Stereo R/L ( Audio Input of PC, DVI)

Speaker Output Cinch Type X 4Port(Stereo L/R)

External Control Port Mini D-Sub 9Pin X 1Port 2.4 Accessory Item Specification

Standard Power Code, RF Cable

Option Remote Controller, Battery, Owner’s manual, Speaker System, Table Stand, Wall Mount, Ceiling Mount



2.5 Dimension / Weight Item Dimension (Unit : mm) Weight (Unit : Kg) Main Only 791.8(W) X 592.4(H) X 102(D) 18 Kg

With Stand 791.8(W) X 615.4(H) X 250(D) 20 Kg

With Stand and Speaker 991.8(W) X 615.4(H) X 250(D) 24 Kg 3. Electrical Specification 3.1. I/O Signal

3.1.1. Signal Type Item Type Remark

TV Euro RF Connector TV RF/CATV (PAL/SECAM) SCART1 Euro SCART Jack 21 Pin CVBS, Audio In/Output SCART2 Euro SCART Jack 21 Pin CVBS, S-Video, Scart RGB, Audio In/Output S-Video Mini-Din 4Pin S-Video Input Composite AV Input RCA X 1Port CVBS Input Audio Input (S-video/AV) RCA X 1Port Stereo R/L ( Auto Detect Audio Input of

S-video/AV3) Composite AV Output RCA X 1Port CVBS Output, Monitor Output Audio Output RCA X 1Port Stereo R/L ( Audio Output) Component1 RCA X 1Port Y, Pb/Cb, Pr/Cr(480i/P, 576i/P, 720P, 1080i) Audio Input RCA X 1Port Stereo R/L ( Audio Input of Component1) Component2 RCA X 1Port Y, Pb/Cb, Pr/Cr(480i/P, 576i/P, 720P, 1080i) Audio Input RCA X 1Port Stereo R/L ( Audio Input of Component2) PC / DTV Mini D-Sub 15Pin Female Analog RGB /DTV(480P, 576P, 720P, 1080i)

DVI (DVI-D) Mini D-Sub 29Pin Female Digital RGB /DTV (480P, 576P, 720P, 1080i), HDCP

Audio Input (PC, DVI) RCA X 1Port Stereo R/L ( Audio Input of PC, DVI) Using Your Television in Different Countries You can use your television in many countries. Each country has its own broadcasting standard. Refer to the following table to determine in which countries you can your television. PAL B/G Afghanistan, Algeria, Australia, Austria, Bangladesh, Belgium, Brunei, Burundi, Denmark, Finland, Germany, Ghana, Greenland, Holland, Iceland, India, Indonesia, Italy, Jordan, Kenya, Kuwait, Liechtenstein, Malaysia, Mozambique, Nepal, New Zealand, Nigeria, Norway, Oman, Pakistan, Papua New guinea, Portugal, San Marino, Sierra Leone, Singapore, Spain, Sri Lanka, Sudan, Sweden, Switzerland, Tanzania, Thailand, Turkey, Uganda, Yemen, Zambia, Zimbabwe. PAL I Great Britain, Hong Kong. Ireland, Macao, PAL D/K China, Czech Rep, Hungary, Mongolia, Poland, Romania. SECAM L Andorra, France, Luxembourg, Monaco. SECAM B/G Egypt, Greece, Iran, Iraq, Lebanon, Morocco, Mauritania, Saudi Arabia, Syria, Tunisia. SECAM D/K Bulgaria, Ivory Coast, Russian.



3.1.2. Signal Rating

Specification Item Min. Typ. Max.

Unit Remark

V-Frequency Range 56.25 - 120.0 Hz

H-Frequency Range 31.468 - 64.06 KHz

Pixel Clock - - 108.0 MHz VESA Standard

H/V Sync Level 3.3 5.0 5.25 Vp-p TTL or CMOS Level

VGA/DVI

RGB Input Level 0.6 0.7 0.8 Vp-p Input Impedance 75Ω

Video Input Level 0.85 1.00 1.15 Vp-p

Sync In Level 0.24 0.29 0.32 Vp-p CVBS

Burst In Level 0.14 0.28 0.35 Vp-p Component(Y, Pb/Cb, Pr/Cr) (480i/P, 576i/P 720P, 1080i) 0.6 0.7 0.8 Vp-p Input Impedance 75Ω

Audio Input Level (R/L) 470 630 790 mV

Speaker Output 9 10 12 W Speaker Impedance 8Ω

Hum(Remaining) - - 10 mV

Frequency Response TBD - TBD KHz

Mute Remain Level - - 10 mV

Initial Level 20 - 60 mW

Tone Control -3 - 3 dB

Audio Output

Balance Variation - - 50 mVrms

3.1.3. Sound Pressure Level Specification 1) Measurement Condition

(1) Background Noise Level : Under 30dBA (2) Measuring Pattern : Dynamic Images (only from Full White to Full Black) (3) Measuring Distance : 1m from the rear side of LCD Module (4) Measuring point

Rear Side

Measuring Point

3.2 Power Power Voltage 100 ~ 240VAC±10%

Power Frequency 50 ~ 60 Hz ±3Hz

Power Consumption Typical : 150W Max : 200W

Leakage Current Less than 0.5m Arms(Class II)



4. Display Characteristics 4.1 LCD Panel

4.1.1 Display Performance The following items are measured under stable conditions. The Display characteristics should be measured In a dark room or equivalent state with the methods shown in note (1)

Item Rating Horizontal 1366 X Vertical 768 Pixel

Display Pixel (1 Pixel = 1 R,G,B Cells)

Horizontal 4098 X Vertical 768 cells Display cells

Horizontal 0.510 X Vertical 0.510 cells

R Horizontal 0.170 X Vertical 0.510 mm G Horizontal 0.170 X Vertical 0.510 mm Cell Pitch

B Horizontal 0.170 X Vertical 0.510 mm

Pixel Type R,G,B Vertical Stripe

Horizontal 697.685 mm X Vertical 392.256 mm Effective Display size

27.46 inch (H) X 15.44 inch (V)]

Number of color 16.77 million color

Peak BRIGHTNESS Typical 500cd/ ( Normal Viewing Angle)

Contrast Ratio (in dark room) Typical 600:1 ( Normal Viewing Angle) (3)

Red : Rx = 0.631 ±0.03 , Ry = 0.343 ±0.03

Green : Gx = 0.280 ±0.03 , Gy = 0.600 ±0.03

Blue : Bx = 0.145 ±0.03 , By = 0.060 ±0.03 Color Coordinates (Typical value)

White : Wx = 0.272 ±0.03 , Wy = 0.278 ±0.03

θL 85(Min) 88 (Typ.) Hor.

θR 85(Min) 88 (Typ.)

φH 85 (Min) 88 (Typ.) Viewing Angle

(5) Ver.

φL 85 (Min) 88 (Typ.)

C/R ≥10

Rising Tr 8 msec (Typ.) 12 msec ( Max) Response Time (4) Falling Tf 10 msec (Typ.) 14 msec ( Max) (Note) 1) After stabilizing and leaving the panel alone given temperature for 30min, the measurement

should be executed. Measurement should be executed in a stable, windless, and dark room. 30 min after lighting the back-light. This should be measured in the center of screen

Note 2) Definition of test point



Note 3) Definition of Contrast Ratio (C/R) : Ratio of gray max ( Gmax) & gray min (Gmin) at the center point(5)

of the panel CR = Gmax / Gmin Gmax : Luminance with all pixels white Gmin : Luminance with all pixels black Note 4) Definition of Response time : Sum of Tr, Tf

Note 5) Definition of Viewing Angle : Viewing angle range (C/R ≥10)



4.2 BACK- LIGHT UNIT The back-light system is an direct – lighting type with 20 CCFT(Cold Cathode Fluorescent Tube) The characteristics of 20 direct lamps are shown in the following tables.

Ta=25±2 °C Item Symbol Min. Typ. Max. Unit Note

Lamp Current IL 3.0 5.2 7.0 MArms (1)

Lamp Voltage VL 1040 1100 - Vrms (2)

Lamp Frequency FL 58 - KHz (3)

Operation Life Time Hr 50000 60000 - Hour (4)

0°C , 1840 Start up Voltage Vs - -

25°C, 1415 Vrms (5)

Note) The waveform of the inverter output voltage must be area symmetric and the design of the inverter must have specifications for the modularized lamp. Specified values are for a single lamp. The performance of the back-light, for example life time or brightness, is much influenced by the characteristics of the DC-AC inverter for the lamp. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. When you design or order the inverter, please make sure that a poor lighting caused by the mismatch of the back-light and the inverter(miss lighting, flicker, etc.) never occur. When you confirm it, the module should be operated in the same condition as it is installed in your instrument. Note

(1) lamp current is measured with current meter at cold side. Refer to the block diagram of the back-light unit in the next page for more information.

(2) Lamp frequency may produce interference with horizontal synchronous frequency and this may cause line flow on the display. Therefore We synchronized the lamp frequency to horizontal frequency. (3) Life time (Hr) of a lamp is defined as the time in which it continues to operate under the condition of Ta=25±2 °C and IL = 5.0mArms for a lamp until the brightness becomes 50% or lower than it’s original value. (4) If an inverter has shutdown function it should keep its output for more than I second even if the lamp connector open. Otherwise the lamps may not to be turned on.



5. Function 5.1 External Control

Item Specification Remark

Front Key(OSD) 4 Button External Key Power, Input Select, Volume Up/Down Remote Control IR Remote Control RS-232C Mini D-Sub 9Pin (Male) 1:1 Remote Control and Software Update

5.1.1 Front Key (OSD) Control

1) Key Function 【 TYPE “I” 】

1. INPUT Select : Selects the input signal source. The sequence is TV, SCART 1,SCART 2, S-Video/AV, Component1/2, PC, DVI

2. Volume Up : Increases audio level, or move the input mode.

3. Volume Down : decreases audio level, or move the input mode.

4. IR Remote control sensing lens and power indicator. Normal : Green / Power off :Red 5. Power : Turn on/off the main power(Stand By)

2) OSD Menu adjustment 1 OSD input source menu when you push the select button. 2 Move to menu by up/down button. 3 Select OSD by select button and finish the OSD display.

INPUT VOL/CH SELECT

1 2 3 5 4



5.1.2 Remote controller and key function When using the remote control, always point it directly the IR sensor of plasma monitor.

<PAL/SECAM Type REMOCON>

•MUTE On / off of mute

•POWER Turns the main power on and stand by

•TV / VIDEO Select the signal source from multiple input source of TV, SCART1,

SCART2, S-Video/AV, Component1/2, PC(DTV Y Pb Pr) or DVI

•V.SIZE Change the image size setting, as Wide, Panorama,

Zoom1, Zoom2 and 4:3

•PIP Activate PIP function on Picture

PIP MODE/SOURCE/SWAP/MOVE

•Number key Direct TV channel number input

•PRE CH Go back to previous TV program

•Menu/Set Activate the OSD window, enter the sub-menu

•Back Exit from the current OSD menu or sub-menu

•PG+ / PG- Change the TV channel on TV mode (up or down)

•VOL+ / VOL- Change the audio level ( increase or decrease)

•MTS Multi Channel Television Stereo. Select stereo, mono or Secondary

Audio Program(SAP)

•PG INFO See information regarding the channel that you select

•PICTURE Choose three different modes of picture settings.

•STILL Activate the temporary image with frozen feature

•SOUND Choose the best appropriate audio environment

•SLEEP Time setting for TV off, push button for 10/20/30/60/90/120/150/180

min setting

•TIME Set the Time function

•DIGEST Digests for TV CH

•SKIP Skip the TV Channel

•CH ERASE Erases the TV channel preset

•TTX Activate the teletext, you can toggle “TTX”,”TTX/MIX” and

“TV” mode



5.1.3 RS232C control 1) Set the parameters of communication software

Baud rate: 9600 Data bits: 8 Bit Stop bits: 1Bit Parity: None Device name: Port mane which is connected to LCD Hex: ASCII

2) RS232C Structure Command = [CMD][Set ID][Value]

CMD : Command To control LCD set. Set ID : You can adjust the set ID to choose desired monitor ID number in special menu.

Adjustment range is 1 ~ 99. When selecting Set ID ‘00’, every connected LCD set is controlled.

Value : To transmit command data. 【 Note 】 Set ID and Value are DEC code. (1~99 ) 【 Example 】 You can Set the Set ID is 12, Volume Level is 34.

RS232C Code is“SVO1234” “SVO” is CMD Code(Volume), “12” is Set ID (Decimal 12) “34” is Volume Level (Decimal 34 )

【 How to select setID 】 Press the menu button and then press the CH+ / CH- button to select SETUP/ADVANCED. Press the menu button and Vol+ / Vol- button to select SET ID. Press the PG+ / PG- button to select SET ID Value.

5.2 OSD Menu Adjustment Item



5.2.1 TV VIDEO/DTV Mode 1) PICTURE

-MODE /Standard, Vivid, Mild, User / Contrast, Brightness, Color, Sharpness, Recall - TEMPERATURE /WARM2, WARM1, NORMAL, COOL1, COOL2, - VIDEO NR / ON, OFF - FILM MODE / ON, OFF - SCREEN FORM /16:9, PANORAMA, ZOOM1, ZOOM2, 4:3

2) SOUND

- BALANCE - SOUND MODE /STANDARD, MOVIE, MUSIC, NEWS, USER/ EQUALIZER (PRESS SET)

// 100Hz, 500Hz, 1.5KHz, 5KHz, 10KHz - SPATIAL EFFECT / ON, OFF - AVC / ON, OFF

- MTS / MONO, STEREO, Language A, Language B, Language A+B 3) SETUP

- TRANSLUCENT - PIP /SIZE / OFF, SMALL, LARGE, TWIN

/SOURCE /PICTURE SWAP /POSITION /RIGHT DOWN, RIGHT UP, LEFT UP, LEFT DOWN

- ADVANCED /SET ID / 0~99 /BLUE BACK / ON, OFF /LANGUAGE / 7 NATIONAL SELECTIONS /FRONT KEY LOCK / ON, OFF

4) TIME - TIME SET - ON TIME / ON , OFF - ON CHANNEL /SELECTION - ON VOLUME /1~100 - OFF TIME - SLEEP TIME / OFF, 10, 20, 30, 60, 90, 120, 150, 180Min

5) TV - AUTO SCAN/ 20 NATIONAL SELECTIONS - MANUAL SCAN - FINE TUNE - FINE TUNE - EDIT

5.2.2 RGB Mode 1) PICTURE

- MODE /Standard, Vivid, Mild, User / Contrast, Brightness, Sharpness, Recall - TEMPERATURE /WARM2, WARM1, NORMAL, COOL1, COOL2 - GEOMETRY / H-POSITION

/ V-POSITION / PHASE / NATIVE MODE ON, OFF / AUTO ADJUST

- SCREEN FORM /WIDE, 4:3 2) SOUND

- BALANCE - SOUND MODE /STANDARD, MOVIE, MUSIC, NEWS, USER/ EQUALIZER (PRESS SET)



// 100Hz, 500Hz, 1.5KHz, 5KHz, 10KHz - SPATIAL EFFECT / ON, OFF - AVC / ON, OFF

3) SETUP

- TRNSLUCENT - PIP /SIZE / OFF, SMALL, LARGE, TWIN

/SOURCE /PICTURE SWAP /POSITION /RIGHT DOWN, RIGHT UP, LEFT UP, LEFT DOWN

- ADVANCED / SET ID / 0~99 /BLUE BACK / ON, OFF

/LANGUAGE /6 NATIONAL SELECTIONS /FRONT KEY LOCK / ON, OFF

4) TIME - TIME SET - ON TIME / ON , OFF - ON CHANNEL /SELECTION - ON VOLUME /1~100 - OFF TIME - SLEEP TIME / OFF, 10, 20, 30, 60, 90, 120, 150, 180Min

5.3 MAIN / SUB CONNECTION MAIN CONNECTION

Service Location Part Number Description

LCD I/F (LVDS) CN1 1554A-3141R 1.25mm, 31P R/A

SIGNAL I/F CN2 12505WS-12P 1.25mm, 12P STRAIGHT




OSD I/F CN7 12505WR-12P 1.25mm, 12P R/A

DC IN CN8 35312-1110 2.50mm, 11P STRAIGHT

LCD I/F CN9 SMW250-06P 2.50mm, 06P STRAIGHT

RS-232C I/F J7 D-SUB 9P MALE

DVI I/F J2 10030970-102-026 DVI-I 29P FEMALE

PC/DVI AUDIO I/F J1 UJB-02-14A RCA 2P (WHT/RED)

PC I/F J3 D-SUB 15P MALE

DTV/DVD I/F J8 UJB-06-27A RCA 6P (RED/GRN/BLU)

DTV/DVD Audio I/F J9 UJB-04-13A RCA 4P (WHT/RED)



SUB CONNECTION

Service Location Part Number Description

DC IN CN1 35312-1010 2.50mm, 10P STRAIGHT





AUDIO I/F CN6 SMW250-06P 2.50mm, 06P STRAIGHT

HEAD PHONE CON1 SMW250-06P 2.50mm, 06P STRAIGHT

SCART 1 I/F J4 UPJ-R1-019 SCART JACK 21P

SCART 2 I/F J5 UPJ-R1-019 SCART JACK 21P

S-VIDEO I/F SVD01 S-VIDEO JACK

AV I/O J3 UJB-06-27B RCA 6P (YEL/RED/WHT)

RF I/F RF2 RF JACK 3P (NTSC)

MAIN BOARD CN1 CN2 CN3

PIN NO FUNCTION PIN

NO FUNCTION PIN NO FUNCTION PIN

NO FUNCTION PIN NO FUNCTION

1 GND 12 RX2+ 23 GND 1 A6V 1 C_SUB 2 GND 13 GND 24 GND 2 GND 2 GND 3 RX0- 14 GND 25 TP5 3 SVIDEO_DET 3 Y_SUB 4 RX0+ 15 RXEC- 26 GND 4 AUDIO_MUTE 4 GND 5 GND 16 RXEC+ 27 SCL_3 5 RESETN 5 CVBS_SUB 6 GND 17 GND 28 GND 6 SCL0_3 6 GND 7 RX1- 18 GND 29 SDA_3 7 SDA0_3 7 C_MAIN 8 RX1+ 19 RX3- 30 GND 8 SCL_3 8 GND 9 GND 20 RX3+ 31 NC 9 SDA_3 9 Y_MAIN

10 GND 21 GND 10 GND 10 GND 11 RX1- 22 GND 11 S3V 11 CVBS_MAIN

12 S5V 12 GND



MAIN BOARD CN4 CN5 CN7 CN8

PIN NO FUNCTION PIN


NO FUNCTION

1 GND 1 SCART_R 1 SELECT 1 D_6V 2 PC/DVI_L 2 GND 2 VOL+ 2 D_GND 3 PC/DVI_R 3 SCART_G 3 VOL- 3 D_3.3V 4 GND 4 GND 4 POWER 4 D_3.3V 5 DVD_L 5 SCART_B 5 LED_G 5 D_GND 6 DVD_R 6 GND 6 LED_R 6 D_GND 7 GND 7 SCART_FB 7 S5V 7 D_12V 8 DTV_L 8 GND 8 GND 8 PS_ON 9 GND 9 FS_ID/AV2_CVBS_DET 9 SENSER 9 D_GND

10 DTV_R 10 GND 10 NC 10 STD_5V 11 GND 11 HS_ID/AV1_CVBS_DET 11 NC 11 THER_DE 12 AV/CVBS_DET 12 GND 12 NC

SUB BOARD CN1 CN2 CN3 CN4 PIN NO FUNCTION PIN


NO FUNCTION

1 A5V 1 A6V 1 C_SUB 1 GND 2 RTN 2 GND 2 GND 2 PC/DVI_L 3 A12 3 SVIDEO_DET 3 Y_SUB 3 PC/DVI_R 4 RTN 4 AUDIO_MUTE 4 GND 4 GND 5 12VAMP 5 RESETN 5 CVBS_SUB 5 DVD_L 6 12VAMP 6 SCL0_3 6 GND 6 DVD_R 7 RTN_A 7 SDA0_3 7 C_MAIN 7 GND 8 RTN_A 8 SCL_3 8 GND 8 DTV_L 9 VT 9 SDA_3 9 Y_MAIN 9 GND

10 RTN 10 GND 10 GND 10 DTV_R 11 S3V 11 CVBS_MAIN 11 GND 12 S5V 12 GND 12 AV/CVBS_DET SUB BOARD CN5 CN6 CON1

PIN NO FUNCTION PIN

NO FUNCTION PIN NO FUNCTION

1 SCART_R 1 NC 1 L_OUT 2 GND 2 AUDIO L_GND 2 L_GND 3 SCART_G 3 AUDIO L 3 R_OUT 4 GND 4 NC 4 R_GND 5 SCART_B 5 AUDIO_GND 5 SPK_MUTE 6 GND 6 AUDIO R 6 GND 7 SCART_FB 8 GND 9 FS_ID/AV2_CVBS_DET

10 GND 11 HS_ID/AV1_CVBS_DET 12 GND



Location of Connectors

CN7

CN9

CN5

CN3

CN2

CN8 CN1

CN4 CN4

CN5

CN1

CN3

CN2

CN6



5.4 INPUT/OUTPUT CONNECTOR 5.4.1 J7 RS-232C INPUT TERMINAL (9pin Mini D-Sub)

Controls the monitor functions externally using by external equipments. Connects with Computers via RS-232C terminal.

Pin No. PC Signal LCD (Male) Design

1 DCD NC

2 RXD Go to pc pin no.3(TXD)

3 TXD Go to pc pin no.2(RXD)

4 DTR NC

5 GND GND

6 DSR NC

7 RTS NC

8 CTS NC

9 RI NC

5.4.2 J1, J9, J3 AUDIO INPUT TERMINAL (RCA)

Connects with audio output terminal of the VCR, DVD or similar devices. Pin No. Signal Note(Female) Design

Signal Audio Right

GND Red Color

Signal Audio Left

GND White Color

5.4.3 J3 PC (RGB) or DTV INPUT TERMINAL (15Pin Mini D-Sub)

Connects with computer monitor or DTV Receiver output terminal. Pin No. PC Signal LCD (Female) Design

1 Red Red 2 Green Green 3 Blue Blue 4 N.C N.C 5 GND(DDC) GND(DDC) 6 GND(R) GND(R) 7 GND(G) GND(G) 8 GND(B) GND(B) 9 N.C N.C 10 Logic GND Logic GND 11 N.C N.C 12 SDA(DDC) SDA(DDC) 13 H-Sync H-Sync 14 V-Sync V-Sync 15 SCL(DDC) SCL(DDC)

R L Signal

GND

1 4 53

7 8 96

2



5.4.4 SVD01 S-VIDEO INPUT TERMINAL (Mini Din 4pin) Connects with S-VHS output terminal of the VCR or DVD players.

Pin No. Signal Note (Female) Design

1 GND(Y)

2 GND(C) GND

3 Y Brightness

4 C Color

5.4.5 J8 COMPONENT1,2 (Y, Pb/Cb, Pr/Cr) INPUT TERMINAL (RCA)

Connects with component output terminal of the DVD players.

Pin No. Signal Note(Female) Design

Signal Y

GND Green Color

Signal Pb/Cb

GND Blue Color

Signal Pr/Cr

GND Red Color

5.4.6 RF2 TV ANTENNA TERMINAL (USA RF Connector)

Connects with RF or Cable TV antenna cable.

Pin No. Signal Note (Female) Design

1 Signal RF or Cable TV

2 GND GND

Signal GND

5.4.7 J3 (TOP) MONITOR (COMPOSITE) OUTPUT TERMINAL

Connects with composite output terminal of VCR or DVD players.


1 Signal

2 GND Yellow Color


Signal Audio Left GND

White Color

Signal Audio Right GND

Red Color

4 3

2 1

Y Pb/Cb

Signal GND

Pr/Cr

Signal

GND

L R Signal

GND



5.4.8 J3 (BOTTOM) COMPOSITE INPUT TERMINAL Connects with composite output terminal of VCR or DVD players.


1 Signal

2 GND Yellow Color


Signal Audio Left GND

White Color

Signal Audio Right GND

Red Color

5.4.9 SPEAKER OUTPUT TERMINAL

Connects with external speakers and match the Color(Red to Red, Black to Black) of Speaker cable.


1 Signal

2 GND Audio Right Output

3 GND

4 Signal Audio Left Output

R R GND L GND L

5.4.10 AC POWER INPUT TERMINAL

Firmly insert the accessory power cord as far as it goes into the power input Terminal. Firmly push the power cord plug as far as it goes to the power socket.

Pin No. Signal Note Design

1 E Earth

2 N Neutral

3 L Line

E L N

5.4.11 J7 DVI(DIGITAL) TERMINAL (29Pin Mini D-Sub)

Connects with the computer monitor or DTV Receiver output terminal.

Pin No. PC Signal LCD (Female) Design

1 TX2+ TX2+

2 TX2- TX2-

3 TX2/4 SHIEILD TX2/4 SHIEILD

4 TX4+ TX4+

Signal

GND

L R Signal

GND



5 TX4- TX4-

6 DDC CLK DDC CLK

7 DDC DATA DDC DATA

8 NC NC

9 TX1+ TX1+

10 TX1- TX1-


12 TX3+ TX3+

13 TX3- TX3-

14 +5V +5V

15 GND GND

16 HP DETECT HP DETECT

17 TX0+ TX0+

18 TX0- TX0-


20 TX5+ TX5+

21 TX5- TX5-

22 TXCLK SHEILID TXCLK SHEILID

23 TXCLK + TXCLK +

24 TXCLK - TXCLK -

25~29 NC NC

5.4.12. SCART1, 2 INPUT or OUTPUT TERMINAL (21Pin) Connects to the computer monitor or DTV Receiver output terminal.

Pin No. PC Signal LCD (Female) Design

1 FS_R_OUT FS_R_OUT

2 FS_R_IN FS_R_IN

3 FS_L_OUT FS_L_OUT

4,5,9,13,14 17,18,21 GND GND

6 FS_L_IN FS_L_IN

7 SCART B SCART B

8 FS ID FS ID

10,12 NC NC

11 SCART G SCART G

15 SCART R C SCART R C



16 SCART FB SCART FB

19 MONITOR OUT MONITOR OUT

20 FS_CVBS_Y FS_CVBS_Y

6. Mechanical Specification

6.1 Dimension (With Stand) With Stand and Speaker : 791.8mm(W) X 615.4mm(H) X 250mm(D) Appendix - 1

6.2 I/D label Based on Harsper Rating label Appendix - 12 6.3 Packing

Paper Composite Double Wall-5 Level, EK300 / B160/ K200 / B160 / EK300

Dimension 932mm*295mm*660mm(W * D * H)

Design of printing Based on Harsper standard

Packing Manual Appendix – 2

6.4 Weight

Weight Product: 20 kg Weight Packing: 25 kg

6.5 Accessories 6.5.1 RF Cable

1) Type : PAL (Male to Male) 2) Color : Black 3) Length: 1500 ± 30mm Appendix - 4

6.5.2 Power Code 1) Type : 3 Poles 2) Rating : 125V/7A 3) Color : Black 4) Length: 1800 ± 50mm Appendix - 5

6.6 Optional 6.6.1 External Speaker

1) Input Power : 7 Watt X 2Channel 2) Input Impedance : 8 ohm 3) Dimension : Appendix – 6/7

6.6.2 Table Stand 1) Type: United 1) Dimension: Appendix – 8/9

6.6.3 Wall Mount Bracket 1) Type : Fixed Wall Mount Bracket 2) Dimension : Appendix – 10/11



7. Environment Test

7.1 Temperature, Relative Humidity and Altitude No. Item Rating

Operational 0 to 45

Storage -15 to 75 Temperature

Temperature Slope 1.5/minute max. 1

* Maximum glass surface temperature must be kept less than 80 Operational 30 to 80 % RH (no condensation)

2 Humidity Storage 30 to 90 % RH (no condensation)

Operational 800 to 1114 hPa (Altitude : 0 to 2,000 m) 3 Pressure

Storage 600 to 1114 hPa (Altitude : 0 to 4,500 m)

7.2 Random Vibration Teat(Packaging) Appendix – Test Report

Stroke Z-Direction

Frequency 10～200Hz

Acceleration 9.8 (=1.0Grms)

Test Time 1Hr ( Z-Direction)

7.3 Drop Test(Packaging) Appendix – Test Report

Test condition 1Corner, 3Edge, 6Face

Height 31Cm

Front Face 1Corner Bottom Face

Left Face Right Face

Top FaceBack Face

1Edge

2Edge

3Edge



8. LCD Module Defect Criterion

8.1 LCD Module Cell Defect Specification 8.1.1 Definition In some cases a panel may have defective cells that cannot be controlled.

These defective cells can be categorized into three types; 1) Non-Lighting cell defect : defect in which the cell is always off 2) Non-Extinguishing cell defect : defect in which the cell is always on 3) Flickering cell defect : defect in which the cell is flickering

8.1.2 Measuring Area

8.1.3 Cell Defect specification

Specification Item

Number of Cell Defects Distance Between Cell defects

Non-lighting Cell Defect

Zone A : 2 and Less Zone B : 8 and Less

Non-Extinguishing Cell Defect

Zone A : Zero Zone B : 2 and Less

Flickering Cell Defect

Zone A : Zero Zone B : 2 and Less

Total defect Total number of cell defects In zone A and zone B is 8 And less

Regardless of A and B zone,

- Distance between NLs is 15mm - Distance between NL and NEF is 15mm - Distance between NEFs is 30mm

【 Note 】

NL : Non-lighting cell defect NEF : Non-extinguishing cell defect

and Flickering cell defect

Zone B

Zone A

W

H

W/4 W/2 W/4H

/4

H/2

H/4



9. Timing Chart

9.1 Analog R, G, B Timing NO. Proposed Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz)

1 EGA 640*350 31.468 70.09 25.17

2 EGA 640*350 37.861 85.08 31.50

3 DOS 720*400 31.469 70.08 28.32

4 DOS 720*400 37.927 85.03 35.50

5 VESA(VGA) 640*480 31.469 59.94 25.17

6 Macintosh 640*480 35.000 66.66 30.24

7 VESA(VGA) 640*480 37.861 72.80 31.50

8 VESA(VGA) 640*480 37.500 75.00 31.50

9 VESA(VGA) 640*480 43.269 85.00 36.00

10 VESA(VGA) 640*480 45.913 90.03 38.20

11 VESA(VGA) 640*480 53.011 100.04 45.80

12 VESA(VGA) 640*480 64.062 120.00 55.35

13 VESA(SVGA) 800*600 35.156 56.25 36.00

14 VESA(SVGA) 800*600 37.879 60.31 40.00

15 VESA(SVGA) 800*600 48.077 72.18 50.00

16 VESA(SVGA) 800*600 46.875 75.00 49.50

17 VESA(SVGA) 800*600 53.674 85.06 56.25

18 VESA(SVGA) 800*600 56.000 90.00 57.30

19 VESA(SVGA) 800*600 64.016 100.00 69.65

20 Macintosh 832*624 49.725 74.55 57.28

21 VESA(XGA) 1024*768 48.363 60.00 65.00

22 VESA(XGA) 1024*768 56.476 70.06 75.00

23 VESA(SXGA) 1280*1024 64.0 60.0 108.00

24 Native Mode 1280*768 47.7 60.0 80.136 9.2 DTV Timing

NO. Proposed Resolution H-freq(kHz) V-freq.(Hz)

1 SDTV 480P 720*480 31.47 59.94

2 SDTV 576P 720*576 31.25 50.00

3 HDTV 720P 1280*720 37.50 50.00

3 HDTV 720P 1280*720 45.00 60.00

4 HDTV 720P 1280*720 44.96 59.94

5 HDTV 1080I 1920*1080 33.75 60.00

3 HDTV 1080I 1920*540 31.25 50.00

6 HDTV 1080I 1920*1080 33.72 59.94



10. Firmware Download 10.1 Firmware Upgrade Instruction Guide

First, copy the download program (.exe file) in the proper folder of your operating system to the upper folder which contains this document and firmware data. ( "/Window 98" for Windows 95, 98, Me and "/Windows 2000 xp" for Windows 2000 and xp.) Firmware Upgrade Before start to upgrade read whole guide carefully A. the upgrade Program needs Microsoft Windows 2000 or XP Run File name : Birch Download Win2K.exe

10.1. 1Start Setup Menu

Set up “Com Port” : Select connected Serial Port between COM1 and COM 10 (ex : COM1 or

CCOM2)

Baud Rate is 57600. (Default is 57600)



10.1.2 Port Setup

After set up Com Port, clik “Port Setup”. And you can see below Notice.

10.1.3 Load

Choose Firmware folder and Load the file.

- Select the target file, which format is only binary file

10.1.4 Download.

After select Firmware file, click the “Run Download”.

Status bar is waiting for Download process like a “Ready Signal…”



If you fail downloading, you can find message “Fail to Communication”

You must close Downloader window and back to Step 1-1

After click “Run Download”, you are ready to Download. And connect AC-Power code.

Then it starts Download.

Caution: If AC-Power code is already connected, Pull out and re-connect 30 sec later.

Then it starts Download.

When it starts Download, existing memory in the Flash Memory will be deleted. And it will start to

copy Boot Block. Herewith LED shows Amber color for 2 sec.

You have to be very careful “Power Off” and disconnection of Serial Port at this time.

LED color process: Green On(Power On) Amber On(Erase) Red Blanking (Data Copy)

< Window shows the new program is being downloaded. into the flash IC >



10.1.5. After Download, you can see “Wait Initialize” message.

(This is not applicable to Win95/98 )

After Download, ROM will be reset. During Reset, LED shows Green and RED color alternately. It

takes about 5min to Download Firmware. If it takes over 10 min, disconnect AC-Power Code for 1

min and Upgrade again.

Initialize process will be carried out after Download. During the Initialize process,

The LED blinks Green and RED color alternately. If it is old version, LED shows

Orange color during the Initialize Process. And after Initialize process, LED shows

RED Color. DO NOT THE POWER DURING THE INITIALIZE PROCESS BUT

WAIT OVER 1MIN. If LED shows Orange color, wait about 1 minute without Turning off the power.

After Initialize the LED shows normal green color. Then you are ready to watch

PDP. If you should up grade Firmware again from the beginning. Please make

Sure below issues during the Download process.

When initialize is completed, ”Download Complete” is displayed.

Be careful below items during Download.

1. During Erase and Boot Code Copy

: Do not cut the Power and disconnect Serial Port. If it happens, Main Board must be exchanged.

2. Normal Data Copy

1). When the Serial Port is disconnected.

- LED will be changed from RED to Green for standby status. Re-connect Serial

Port again when LED is RED. It starts Download again.

2). When Power is Off

- Close the Window and start the download process from the beginning.



11. RS-232C Command List Command Table Picture (1/2)

Parameter Control Item Command

Input Response Remark

TV 00 00 SCART 1 01 01 SCART 2 02 02

S-Video /AV 03 03 Component 1 04 04 Component 2 05 05

PC 06 06

Source Select

DVI

p s s

07 07

Standard 00 Vivid 01 Mild 02

Picture mode

User

p p m 00

03

Rolling Input

Cool 2 00 00 Cool 1 01 01 Normal 02 02 Warm 1 03 03

Color Temperature

Warm 2

p c t

04 04

Direct Input

WIDE 00 Panorama 01

Zoom1 02 Zoom2 03

V.Size

4:3

p v z 00

04

Rolling Input

OFF 00 00 Video NR

ON p n r

01 01 Direct Input

00 00 Down Input Contrast p c r

01 01 Up Input 00 00 Down Input

Brightness p b r 01 01 Up Input 00 00 Down Input

Color p c o 01 01 Up Input 00 00 Down Input

Sharpness p s h 01 01 Up Input

Recall p r e 00 00 OFF 00 00

Still ON

p s t 01 01

Direct Input

OFF 00 00 Black Enhancer ON

p b e 01 01

Direct Input



Picture (2/2)



OFF 00 Small 01 Large 02 PIP Size

Twin

p p z 00

03

Rolling Input

TV 00 SCART1 01 SCART 2 02

S-Video /AV 03 Component 1 04 Component 2 05

PC 06

PIP Source

DVI

p p s 00

07

Rolling Input

Right Down 00 Right UP 01 Left UP 02

PIP Position

Left Down

p p p 00

03

Rolling Input

PIP_Swap(Cross) p p x 00 00 00 00 Down Input

Geo_H Position p g h 01 01 Up Input 00 00 Down Input

Geo_V Position p g v 01 01 Up Input 00 00 Down Input

Geo_Phase p g p 01 01 Up Input 00 00 Down Input

Geo_Auto p g a 01 01 Up Input 00 00 Down Input

Geo_Native Mode p g n 01 01 Up Input

Sound (1/2) Parameter

Control Item Command Input Response

Remark

Standard 00 Movie 01 Music 02 News 03

Sound Mode

User

s s m 00

04

Rolling Input

OFF 00 00 Spatial Effect ON

s s e 01 01

Direct Input



Sound (2/2)



OFF 00 00 AVC

ON s a v

01 01 Direct Input

OFF 00 00 Mute

ON s m u

01 01 Direct Input

Mono 00 00 Stereo 01 01

Language A 02 02 Language B 03 03

Language AB 04 04

MTS

SAP

s m t

05 05

Direct Input

Volume s v o (0~99) (0~99) Direct Input 00 00 Down Input

Balance s b a 01 01 Up Input

Miscellanaous (Setup) (1/2)



OFF 00 00 Power

ON m p o

01 01 Direct Input

OFF 00 00 Remote Lock ON

m r l 01 01

Direct Input

OFF 00 10 01 20 02 30 03 60 04 90 05 120 06 150 07

Sleep Time

180

m s t 00

08

Rolling Input

OFF 00 00 Blue Back

ON m b b

01 01 Direct Input

OFF 00 00 Front Key Lock

ON m f p

01 01 Direct Input

English 00 00 Deutsch 01 01 Francais 02 02 Espanol 03 03 Italiano 04 04

Русский 05 05

Language

Português

m l a

06 06

Direct Input



OFF 00 Text 01 TTX Mode Mix

m x m 00 02

Rolling Input

Red 00

Green 01

Yellow 02 TTX Funtion

Cyan

m x f 00

03

Rolling Input

TV (1/1)


Input Response 비고

00 00 Down Input Fine Tune t f t

01 01 Up Input PR Up t p u 00 00 Direct Input

PR Down t p d 00 00 Direct Input PR Number(0~99) t p n Dec(0~99) Dec(0~99) Direct Input

Pre. PR t p c 00 00 Direct Input PIP SUB CH Up t s u 00 00 Direct Input

PIP SUB CH Down t s d 00 00 Direct Input OFF 00 00

Digest ON

t d i 01 01

Direct Input

Belgium 00 00 Czech Rep. 01 01

Denmark 02 02 Germany 03 03 England 04 04

Spain 05 05 Finland 06 06 France 07 07

Great Britain 08 08 Greece 09 09 Hungary 0a 0a Ireland 0b 0b

Italy 0c 0c Netherlands 0d 0d

Norway 0e 0e Poland 0f 0f Sweden 10 10

Switzerland 11 11 TurKey 12 12

East Europe 13 13

Auto Scan

Others

t a s

14 14

Direct Input



12. Remote Control IR Code Value 12.1 Remote Control IR Code Value

< PAL > Function Vaule Power 00 Mute 17 Pre.CH 04 V.Size 40 Favorite 1A 1 01 2 02 3 03 4 05 5 06 6 07 7 09 8 0A 9 0B 0 18 TEXT 0D INPUT 42 Menu/Set 0F Back 1B PG+ 10 PG- 13 VOL- 12 VOL+ 11 MTS 41 PG INFO 43 PICTURE 16 STILL 19 SOUND 1C SLEEP 08 TIME 1D DIGEST 1E ERASE 1F SKIP 44 INSERT 14 REPLACE 15 MODE 45 SOURCE 46 SWAP 47 MOVE 48



12.2 Discrete Code Value Function Code Remark

POWER-ON (Only) A5 Create additional Power On button differ to current toggle style one

POWER-OFF (Only) 55 Create another button for power off.

- - - TV 81 Move to TV mode without opening Source change window

SCART 1 82 Move to SCART1 mode without opening Source Change window SCART 2 83 Move to SCART2 mode without opening Source change window

S-Video/AV 84 Move to S-Video/AV mode without opening Source change window Component1 85 Move to Component1 mode without opening Source change window Component2 86 Move to Component2 mode without opening Source change window

PC 87 Move to PC mode without opening Source change window DVI 88 Move to DVI mode without opening Source change window

13. Trouble Shooting

13-1. The LED Lighting Status of operation NO LED lighting Status 1 Stand By Mode Lighting RED 2 Normal Operating Lighting Green 3 No Input Blanking Green 4 Remote Control IR Signal Input Green Bilnking 5 During RS-232C Control Lighting Green 6 In Firmware Upgrading Green On(2sec) Amber On(8sec)

Red Bilnking(3min) -> (stand by or initializing)

7 In System Initializing Bilnking Red and Green 8 Aging Mode(In Fatory Only) Bilnking Red 9 Sensing Remocon input Blink off and green in 0.5sec

13.2 Trouble Shooting Flow Chart Go to Following routine dependent problems to trouble shooting.

1. No Power Problems 2. No Video Problems 3. Keypad or Remote Control Problems 4. Panel Problems for Performance with test PC signal 5. Back Light Problems 6. Image Quality Problems 7. Audio Problems



Turn on the TV set(not soft Power on)

Check LED lit Green and/or

Red?

Check Is LEDlit green(2 sec) and

go red

PICTURE DISPLAY(GOOD FUNCTION)

YES

NO

YES

B

A

NO

<1> No Power Problems

Go to Keypad orRemote Problems

Check LEDoff(0.5sec) andlighting Green?

YES

NO

Checkdisplay Logo

and/or sandglass in5sec to 8secafter soft on

Check Amberblinks after LED

light 5sec to 7secWhen start AC On



A

CheckAC Inletcable

Check Fuse

checkRelay on/off

Remove cable fromCN707,CN702,CN708,CN703,CN705

on power board and short #3 and #4 pinof CN703, Check the output vlotage

after gaving PS-ON signal

Chack 5V point at CN707Chack 120V point at CN702Chack 120V point at CN708check each output at CN703check each output at CN705

AC Inlet CableReconnecting

Verify normal working of TV byrestarting

Replace SMPS

ReplaceSMPS

CheckVoltagesOutput

Power BoardChange

YesNo

Confirm That Unit Is Good ByStarting Again

Solve TheProblem?

Short #3 and #4 pin at CN703after removing CN707 ,

CN702,CN708,CN703,CN705

Check the outputvoltage after CN705

connecting.


connecting


connecting다.


connecting.


connecting

YES

YES

YES

YES

Replace thePANEL

NO

Replace Mainboard

NO

NO



NoVideo

Green LED?

Check back lightlamp on or off

Display “No Input’and blinking green

LED?

LED GreenBlinking

Check input signalcable.

Replace MainBoard

Verify normalworking of TV by

restarting

Amber LED after7sec Green LED

Check the powerback light on

signal from CN706

Verify normal working ofTV by restarting

Check LVDS cable.Is it OK? Reconnect LVDS Cable

Is LED green? Is LEDblinking when you press

the R/C button?

Green LED Blink Replace the mainboard

Main board is fine

Replace the panel

Verify normalworking of TV by

restarting

YES

YES

NO

YES

NO

NO

NO

YES

YES

NO

<2> No Video Problems

** Important Notice : This LCD Panel inside of LCDTV has function of automatic lamp off if LCD signal isnot connected even if the lamp power and controlsignal is good.

You can see that screen isslightly brighter than off statuseven though there is no signalof LVDS in LCD Panel

Is there anyproblem after

changing SMPS?

Is sound OK ?

YesNO

No Change Main and/or Sub Board



K e y p a d a n d re m o ted o e s n o t re s p o n d to k e y

p re s s e s

D o e s T h eR e m o te C o n tro l

w o rk ?

O s d C a b le o k ?

C h a n g e O S D B o a rd(2 O S 9 0 0 1 4 )

In fra re d re m o te p ro b le m

U s e p ro p e r b a tte r ie sw ith g o o d c o n d it io n in

re m o te c o n tro l

D o e s th ere m o te w o rk ?

A im th e re m o te a t e a c ho f th e IR re c e iv e rs o n

th e T v

O S D c a b le o k ?

C h a n g e th e O S Dc a b le (3 H N 4 0 0 2 6 F -0 2 )

C h a n g e O S D B o a rd(2 O S 9 0 0 1 4 )

Y E S

Y E S

Y E S

Y E S

N O

D o e s th ere m o te w o rk ?

N O

< 3 > K e y p a d o r R e m o te P r o b le m s

C h e c k S ta n d B y5 V O K ? Y o u C a n C h e c k

S ta n d B y 5 V a t M a in B o a rdC N 8 P in N u m b e r # 1 0(M a rk e d a s S T B -5 V )

B

E N D

N O

Y E S

N O



START

Is screenscrollig?

ReplaceMainBoard

ReplaceCable

Is screenflickering?

ReplaceInverterBoard

ReplaceMainBoard

ReplaceLCD

Module

Is LCD linedefective?

ReplaceLCD

Module

Bad uniformityReplaceInverterBoard

ReplaceLCD

Module

Is screenwhite?

ReplaceMain Bord

ReplaceLCD

Module

Check Panel signalcable connectivity

No Trouble Found

END

YES NO

NO YES YES

NO

NO

NO

NO

YES NO NO

YES YES YES

YES

YES

YES

NO

NO NO

YESYESYES

YESYES

YES

<4>PANEL Problems Performance(with test pc signal)



No back light on

Back light ON?

Horizontally shadowscreen

Upper side is dark?

Exchange uper sideinverter and cable

Exchange lower sideinverter and cable

Change LCD Module

Check LCD signalcable status

Exchange LCDcontrol board

NO

YES

YES

YES

NO NO

NO

START

<5>Back light Problems



The image is not good or have someproblems. The lamp is lit

If the image problem seems to be caused from panel itselfgo to panel Performance process to define

Checkconnection

status of cableon port?

Check same withother input ?

Press “still”button ?

Change Main Boardand Is LCD signal

cable properlyconnected

END

Check Mainand/or sub board

including probem port?

Change cable

Go to Panel Performanceprocess

YES

NO

NO

YES

YES

NO

NO

YES

NO

<6> Image Quality Problem



S T A R T

M a k e s u re th a t s o u n d o u tp u tA u d io c a b le is p ro p e r ly

c o n n e c te d

A u d ib le

Is s o u n db ro k e n ?

C h e c k w ith o th e rin p u t p o r t

c o n n e c tio n

Is s o u n db ro k e n ?

Is v o lu m ea d ju s ta b le ?

E N D

C h a n g eS p e a k e r

C a b le

C h a n g eS u b B o a rd

C h a n g eS p e a k e r

C h a n g em a in

B o a rd

Y E S

N o T ro u b le F o u n d

Y E S

N O

N O N O

Y E S Y E S

Y E S

Y E S

Y E S

C h a n g e M a in o rS u b b o a rd h a v e

P ro b le m

< 7 > A u d io P ro b le m



14. Block Diagram



15. Exploded View

HL-32XXB EXPLODED VIEW(1) FIXER

(3) AL Frame TOP

(4) AL Frame Side L

(5) AL Frame Side R

(6) AL Frame BOTTOM

(7) LCD Module(SS, LG)

(8) BRK BOARD

(9) BRK BACK

(10) BOARD VSC

(11) BOARD TUNER

(12) BOARD POWER

(13) STAND GUIDE

(14) COVER BACK

(15) BOARD OSD

(16) BRK OSD

(20) CABLE LVDS

(21) CABLE INVERTER

(22) CABLE INVERTER

(23) CABLE POW ER INNET

(24) CABLE POW ER 11P

(25) CABLE POW ER 10P

(26) CABLE LVDS

DESCRIPTION QT'Y

4

2

1

1

1

1

1

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

4

2

27

12

8

8

(27) CABLE POW ER CONTROL

(28) CABLE OSD

(29) CABLE SPEAKER

(30) CABLE DATA

(31) SCREW , T/T-S TYPE-B BIN 3*6 NISI

(32) SCREW , T/T-S TYPE-C BIN 3*6 NISI

(30) SCREW , T/T-S TYPE-C BIN 4*8 NISI

(31) SCREW , T/T-S TYPE-C BIN 3*6 BLK

(32) SCREW , T/T-S TYPE-B BIN 4*8 NISI

(1)

(2)

(3)

(4)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

(5)

(15)

(16)

(20)

(21)

(22)

(24) (25)

(23)

(27)

(26)(24)

(25)

(29)

(28)

(30)

7

14

(33) SCREW , T/T-S TYPE-B BIN 4*8 BLK

(34) SCREW , M/S BIN 3*10 NISI

(35) SCREW , M/S SEMS 3*8 NISI

19

(12)

(10)

(11)

(17) BOARD OSD

(18) LENS

(19) KNOB

(16)(17)

(18)

(19)

1

1

4

(31)

(32)

(33)

(34)

(35)

(2) BRK INNER



16. Disassemble Process

16. 1 Back Cover Open

16.1.1 Remove pointed screws (③:T4 x 8, ④:M3x 6) screws on the back cover.

16.1.2 Open the back cover

16.1.3 Remove pointed screws (②: H3 x 5L , ①: T3 x 12) on the back bracket

16.2. Removal of Stand Guide

1 Remove stand guide B ( T4 X 8)



16.3. Removal of Back Bracket

① Remove nut on antenna cable. 2 Remove inlet shield cable from SMPS board

3 Remove inlet ground cable

4 Remove power inlet from back bracket.

5 Remove speaker cable connected sub board from back bracket

6 Remove back bracket



16.4. Removal of Cables

① Remove Power Control cable from SMPS and LCD Module ( f )

② Remove LVDS cable connected LCD Module and main board LVDS connector unit. ( e )

③ Remove Power Cable ( 11 Pin ) connected SMPS and Main Board ( d )

④ Remove Power Cable ( 10 Pin ) connected SMPS and Sub Board ( c )

⑤ Remove Inverter Cable 2 connected SMPS and Main Board ( b )

⑥ Remove Inverter Cable 1 connected LVDS board in LCD Module and Module Lamp unit.

16.5. Removal of Cables

① Remove Data Cable ( 10 Pin ) connected Main Board and Sub Board

② Remove Ground Cable on upper left side of Main Board and disconnect OSD Cable that connects OSD

Board located beneath of Extrusion Bar and OSD connector unit on Main Board

CN9 CN1 CN8 CN1



16.6. Removal of Power Supply and VSC Board

① Remove screws on Main Board and Sub Board.

② Remove SMPS Board with SMPS insulator.

① Remove screws on Main Board and Sub Board.

② Remove SMPS Board.

①

①

①

①

①

①①

① ②

②

②

②



16. 7. Removal of LCD Module

① Disassemble Extrusion Bar from LCD Module.

② Remove Board Bracket from LCD Module.(①,②)

③ Remove Inner Bracket from LCD Module.()

④

16. 8.Removal of OSD Board

① Remove OSD Connector from OSD Board



② Remove OSD Board from bracket

③ Remove OSD Board Bracket and OSD Ground Cable from Extrusion Bar.

④ Remove OSD Lens/Knob

16.9. Frame Breakdown

① Remove Aluminum Bracket Frame at 4 corners of Extrusion Bard

② Remove screws

③ Remove Frame Fixture at 4 corners.

16.10B. Replaceable Parts List

No. Part Name Part No.

1 Top Extrusion Bar Frame ( F type) 4M320B01

2 Bottom Extrusion Bar Frame ( F type) 4M320B02

3 Side Extrusion Bar Frame ( F type) 4M320B03

4 Al Frame Bracket

1 7

5

3 4

8

10

9

6

2

14

16

19

17 13

21 22 20

12 11

15

23

18

24



5 Frame Fixer 4M300A07

6 LCD Panel Bracket

7 Board Bracket 4M325B02

8 Back Bracket 4M325B02

9 Stand Guide A 4M325B05

10 OSD Bracket “I” Type 4M325B04

11 Main Board 2OTPD033

12 Sub Board 2OTPD028

13 SMPS 2OTP046

14 OSD Board 4 Key ( “I” Type) 2OS90014

15 Inverter Cable A 3HN30033

16 LVDS Cable 31Pin 3HN20047

17 Power Control Cable 3HN60053

18 Inverter Cable “ A” 3HN30033

19 OSD Cable 3HN40026F-01

20 Power Cable 10 Pin 3HN60032

21 Speaker Cable 3HN80022A-05

22 Power Cable 11Pin 3HN60031-01

23 Data Cable 3HN50027

24 Power Inlet Cable Ass’y 3HN70008



17. Disassemble LCD Module

LCD Timing Control Board

Inverter (2pcs)



1.Removal of LCD Timing Control Board

Remove Screws from the protection metal plate.

Find out FPC which is connected LCD Panel and timing control board.

Disconnect FPC by flipping

Remove Logic Board from LCD Module

FPC



2. Removal of Inverter

Remove Screws from the protection metal plate.

Disconneting inverter Cables & FPC Cable

Remove inverter Board

Inverter Cables

Inverter FPC

Cable



18. BOM

NO Part No. Item Qty Remarks

1 1LC320W01-B6K1 TFT-LCD PANEL 1 2 2OTPD033 MAIN BOARD(PAL) 1 3 2OTPD034 MAIN BOARD(NTSC) 1 4 2OTPD028 SUB BOARD(PAL) 1 5 2OTPD032 SUB BOARD(NTSC) 1 6 2OTP046 SMPS BOARD 7 2OS90014 OSD BOARD 1 8 3HN20047 LVDS CABLE 1 9 3HN30033 INVERTER CABLE 2 10 3HN60031-01 DIGITAL 11P CABLE 1 11 3HN60032 ANALOG 10P CABLE 1 12 3HN50027 DATA CABLE 4 13 3HN60053 POWER CONTROL CABLE 1 14 3HN40026F-01 OSD CABLE 1 15 3HN80022A-05 SPERARKER CABLE 1 16 3HN70008 POWER INNET CABLE 1 17 4P420P06 KNOB FUNCTION(SS) 1 18 4P420A01 LENS LED 1 19 4LPDP001 LABEL CAUTION 1 20 4OT20053 SPONGE 36 21 4OT20054 EVA SPONGE 1 22 4OT60004 WIRE SADDLE 2 23 Rubber Cap 1 24 25 4M320B01 FRAME TOP 1 26 4M320B02 FRAME BOTTOM 1 27 4M320B03 FRAME SIDE R/L 2 28 4M300A07 FIXER 4 29 4M325B01 COVER BACK,GOLD 1 30 4M325B02 BRACKET BACK (PAL) 1 31 4M325B03 BRACKET BACK (NT) 1 32 4M325B04 BRACKET OSD 1 33 4M325B05 STAND GUIDE A 2 34 4M325B06 STAND GUIDE B 2 35 4M325B07 BRACKET BOARD 1 36 4M325B08 INNER BRK 2 37 5NUTM30008 STUD,5φ *M3*7L,STAND OFF, NISI 6 38 5SM1E03082 M-S, SEME 3*8 NISI 13 39 5ST1B03062 T/T-S, TYPE-C BIN 3*6 NISI 19 40 5ST1B03064 T/T-S, TYPE-C BIN 3*6 BLK 8 41 5ST1D03084 T/T-S, TYPE-C DIS 3*8 BLK 2 42 5ST2B03062 T/T-S, TYPE-B BIN 3*6 NISI 2 43 5ST2B03104 T/T-S, TYPE-B BIN 3*10 BLK 9



44 5ST2B04062 T/T-S, TYPE-B BIN 4*6 NISI 8 45 5SM1E04062 GND SCREW (4*6) 1 46 5ST1B04082 T/T-S, TYPE-C BIN 4*8 NISI 12 47 5ST2B04084 T/T-S, TYPE-B BIN 4*8 BLK 21 48 M-S, BIN 5*10 NISI 4 49 8BATTE002 BATTERY,1.5V-AAA 2 50 4U320B01 USERS GUIDE (SS) 1 51 3CB20001 CABLE SIGNAL,IVORY 1 52 3CD40004 POWER CORD 1 53 3OT10008 REMOCON,35KEY(PAL) 1 54 4B320B02 BOX MAIN 1 55 4C400B01 CUSHION MAIN SET 1 56 4PE40016 PACKING BAG 1 57 58 4OT50107 Scart Gasket 1 59 4OT50109 Scart Gasket Tape 1 60 EMI Core 1 62 EMI Core 1



APEENDIX – 1 Dimensional Drawing

HL-3200B

APEENDIX–2 Pack Manual



APEENDIX – 3 Carton Box Drawing

APEENDIX – 4 PAL/SECAM RF CABLE



APEENDIX – 5 POWER CODE

Remark 1. Jacket : PVC 2. Color : Black 3. Cord Type : 3G * 0.75mm 4. Rated Voltage ; 1) Cord Set : 250V/10A 2) Plug Cap : 250V/10A,16A 3) Connector Body : 250V/10A

Insulation Color⊙ Light Blue⊙ Brown⊙ Green/Yellow

Annealed Copper Conductor Standard

PVC InsulationPVC Jacket

POWER CORD

APEENDIX – 6 External Speaker Drawing



APEENDIX – 7 External Speaker Packing Method

①

②

③

④ ⑤ ⑥

(1) Bracket X 4Pcs(2) Cable(5m) X 2Pcs(3) Wire Saddle X 2Pcs(4) Screw 4X10mm 8Pcs(5) Screw 4X12mm 8Pcs

B

EXTERNAL SPEAKER PACKING METHOD

Accessory PAPER COMPOSITE

1 CARTON BOX2 CUSHION "L"3 CUSHION "R"4 SPEAKER "L"5 SPEAKER "R"6 ACCESSORY

PRINT "A" COLOR : BLACKPRINT "B" COLOR : BLUE

A

9

APEENDIX – 8 Table Type Stand Drawing (B Type Stand)

DESKTOP STAND DRAWING



APEENDIX – 9 Table Type Stand Packing Method(B Type Stand)

APEENDIX – 10 Wall Mount Bracket Drawing



APEENDIX – 11 Wall Mount Bracket Packing Method

APEENDIX – 12 I/D Label

service manual hl32xxb pal v1 0

Documents

32xxb service manual

protection metal plate

qualified service personnel

verify normal working

pip size

spatial effect

mini din 4pin

extinguishing cell defect