series grm clamp accessories - phd, inclitstore.phdinc.com/pdf.asp?filename=mac04_add1_ec.pdf ·...
TRANSCRIPT
MAC04-ADD1-EC
SERIES GRM CLAMP
ACCESSORIES
Side Proximity Switch Flat Proximity Switch Switch Cover
Blade Mounting Various Tips Spherical Mounting
Wingtips 30° Tips Duckbills
2
REAR PLATE MOUNTWITH SIDE PORTS
BODY OPTIONS: CLAMP ACCESSORIES
B06
GRM2TS-6-45DCB-45DDB-LAA -B06Example Ordering Data:
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
CLAMPSIZE & MODEL
2xC, D, G, H, J, N, P, & S2xF & K
ACCESSORYB06B06
REPLACEMENT KIT NUMBERS IF ORDERED SEPARATELY
NOTE:1) ALL DIMENSIONS ARE REFERENCE UNLESS SPECIFICALLY TOLERANCED
JAW A
JAW B
76,0
101,0 JAW PIVOT
G 1/8(CLOSE PORT)
8,0
17,535,5
4X M6 x 1,0LOCKING THD10,5 DP
35,0
4X THRUHOLE FORM6 SHCS
28,5
57,0
8,017,5
48,5
G 1/8(OPEN PORT)
15,8
69,8 59,3
15,8
69,8 58,2
F & K STYLES ONLY
JAW STYLESC, D, G, H, J, N, P, & S(GRM2TS shown)
JAW STYLESF & K(GRM2TF shown)
BODY ASSEMBLY NO.65337-1265338-12
This option provides a rear mounting plate integral to the body,ports are located on the sides of the plate. The rear surface has fourM6 threads identical to the T mount and four thru holes identical tothe P mount. Overall length is 14,0 mm shorter than a standardbody with a bolt on P mounting plate. The one piece body iscompatible with R, S, W, A, & B mounts.
Available on size 2.
© Copyright 2003, by PHD, Inc. All Rights Reserved. Printed in the U.S.A.
3
B07This option provides a rear mounting plate integral to the body,
ports are located on the rear and sides of the plate. Removable portplugs are installed in the side ports, with the rear ports open.
The rear surface has four M6 threads identical to the T mountand four thru holes identical to the P mount. Overall length is14,0 mm shorter than a standard body with a bolt on P mountingplate. The one piece body is compatible with R, S, W, A, & Bmounts.
Available on size 2.
REAR PLATE MOUNTWITH REAR PORTS
BODY OPTIONS: CLAMP ACCESSORIES
GRM2TS-6-45DCB-45DDB-LAA -B07Example Ordering Data:
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
CLAMPSIZE & MODEL
2xC, D, G, H, J, N, P, & S2xF & K
ACCESSORYB07B07
REPLACEMENT KIT NUMBERS IF ORDERED SEPARATELY
BODY ASSEMBLY NO.65341-1265342-12
8,0
17,5
48,5
G 1/8(OPEN PORT) - PLUGGED
5,0
5,0
G 1/8(CLOSE PORT)
G 1/8(OPEN PORT)
4X M6 x 1,0LOCKING THD
10,5 DP
57,0
28,5
35,5 35,0
25,0 25,0
4X THRU HOLE FORM6 SHCSJAW A
JAW B
76,0
101,0 JAW PIVOT
G 1/8(CLOSE PORT) - PLUGGED
8,0
17,5
15,8
69,8
59,3
15,8
69,8 58,2
F & K STYLES ONLY
NOTE:1) ALL DIMENSIONS ARE REFERENCE UNLESS SPECIFICALLY TOLERANCED
JAW STYLESC, D, G, H, J, N, P, & S(GRM2TS shown)
JAW STYLESF & K(GRM2TF shown)
4
BODY OPTIONS: CLAMP ACCESSORIES
HIGH FORCE CLAMP “2 X 4”B08This option provides a clamp with more force (2046 N with a
S jaw style, 1601 N with a K jaw style). The cylinder portion of theclamp body houses a larger cylinder providing more clamp forcewith little added size and only a 0,2 kg weight adder over GRM2clamps.
Jaw styles S, C, D, G, H, J, N, P, K, and F are available with theB08 body. For jaw dimensions from the pivot pin forward, see theSeries GRM catalog. All GRM2 standard and accessory tips fit theB08. The larger cylinder requires the larger GRM4 mounting brackets.
Available on size 2.
GRM 2 SS-6-45DCB-45DDB-LAA -B08Example Ordering Data:
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
NOTE:1) ALL DIMENSIONS ARE REFERENCE UNLESS SPECIFICALLY TOLERANCED
CLAMP SIZE& MODEL
2xC, D, G, H, J, N, P, & S2xK2xF
WEIGHT ADDERTOTAL CLAMP FORCE
at 6 barkg
0,200,200,20
N204616012046
NOTE:1) For tips, use GRM2 weights, dimensions, and kit numbers.2) For mounting brackets, use GRM4 weights, dimensions, and kit
numbers.
SPECIFICATIONSMOUNTING STYLE
TABCPRSW
MOUNTING BRACKET KITS(use size 4 brackets)
KIT NO.none (standard)
65008-0665016-0664658-0565004-0464648-0264648-0164649-01
JAW STYLESC, D, G, H, J, N, P, & S(GRM2TS shown)
JAW STYLESF & K(GRM2TF shown)
62,0
28,0
43,0
3X M8 x 1,25LOCKING THD13,0 DP
38,0
55,3
11,5G 1/8
(CLOSE PORT)
19,5
JAW A
JAW B
88,0
118,5
11,5
12,5
G 1/8(OPEN PORT)
JAW PIVOT
59,3
58,2
F & K STYLES ONLY
5
BODY OPTIONS: CLAMP ACCESSORIES
CLAMPSIZE & MODEL
2xC, D, G, H, J, N, P, & S2xF & K
ACCESSORYB08B08
REPLACEMENT KIT NUMBERS IF ORDERED SEPARATELY
BODY ASSEMBLY NO.65344-1265345-12
OPEN PORT CLOSE PORTJAW B
JAW A
6
BODY OPTIONS: CLAMP ACCESSORIES
HIGH FORCE CLAMP “2 X 4”W/REAR PORTSB08A
This option provides a clamp with more force (see specificationtable below) and ports located in the slides and rear of the clamp.Removable port plugs are installed in the side ports, with the rearports open. The cylinder portion of the clamp body houses a largercylinder providing more clamp force with little added size and only a0,37 kg weight adder over GRM2 clamps.
Jaw styles S, C, D, G, H, J, N, P, K, and F are available withthe B08A accessory. For jaw dimensions from the pivot pin forward,see the Series GRM catalog. All GRM2 standard and accessory tipsfit the B08A. The larger cylinder requires the larger GRM4 mountingbrackets. (Mounting style A, B, and P are NOT available with thisaccessory.)
Available on size 2.
GRM 2 TS-6-45DCB-45DDB-LAA -B08AExample Ordering Data:
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
NOTE:1) ALL DIMENSIONS ARE REFERENCE UNLESS SPECIFICALLY TOLERANCED
NOTE: Mounting style A, B, & P not availablewith this accessory.
CLAMP SIZE& MODEL
2xC, D, G, H, J, N, P, & S2xK2xF
WEIGHT ADDERTOTAL CLAMP FORCE
at 6 barkg
0,370,370,37
N204616012046
NOTES:1) For tips, use GRM2 weights, dimensions, and kit numbers.2) For mounting brackets, use GRM4 weights, dimensions, and kit
numbers.
SPECIFICATIONSMOUNTING STYLE
TCRSW
MOUNTING BRACKET KITS(use size 4 brackets)
KIT NO.none (standard)
64658-0564648-0264648-0164649-01
JAW STYLESC, D, G, H, J, N, P, & S(GRM2TS shown)
JAW STYLESF & K(GRM2TF shown)
G 1/8(OPEN PORT) - PLUGGED
134,4
G 1/8(CLOSE PORT) - PLUGGED
G 1/8(OPEN PORT)G 1/8
(CLOSE PORT)
29,734,7
8,022,6
2X 7,0
7
BODY OPTIONS: CLAMP ACCESSORIES
POSITION 2 PORTSB09This option provides both ports in position 2 of clamp (jaw A
side of clamp). All jaw styles are available with the B09 body option.For jaw dimensions from the pivot pin forward, see the Series GRMcatalog.
Available on size 2.
GRM2TS-6-45DCB-45DDB-LAA -B09Example Ordering Data:
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
JAW STYLEC, D, G, H, J, N, P, & S
F, K
PORTS65368-1265371-12
BODY PART NUMBERIF ORDERED SEPARATELY
CLAMPSIZE
2
NOTES:1) ALL DIMENSIONS ARE REFERENCE UNLESS SPECIFICALLY TOLERANCED.2) NUMBERS IN CIRCLES INDICATE POSITION (POSITION 2 IS PORT SIDE OF CLAMP).
JAW A
JAW B
97,03X M6 x 1,0
SELF LOCKING THD10,7 DP
14,2
35,5
28,5
2
1
4
3
G 1/8(CLOSE PORT)
G 1/8(OPEN PORT)
2X 38,5
13,3
13,3
F & K STYLES ONLY
G 1/8(CLOSE PORT)
G 1/8(OPEN PORT)
13,3
13,32X 38,5
JAW STYLESC, D, G, H, J, N, P, & S(GRM2TS SHOWN)
JAW STYLESF & K (GRM2TF SHOWN)
8
G07
GENERAL OPTIONS: CLAMP ACCESSORIES
ALUMINUM JAW CLAMP(BOTH JAWS ROTATE)
This option provides a GRM clamp with hardcoated aluminumjaws that reduce the weight of the clamp by 0,3 kg. Both jaws acceptall Series GRM standard and accessory tips. Jaw rotations are thesame as standard GRM clamps. Consult PHD for additional accessorycompatibility. Not available with G01 and G02 options.
No-ear impact plates are standard with this option.Available on size 2.
ROTATIONLETTER
DIMB4J1S1T2
75° x 75° 45° x 45° 22° x 22°mm
114,6148,0
—97,8
mm144,9129,75,072,5
mm160,1105,35,039,1
GRM2TS-6-45-45 SHOWNGRM2T S -6- 45 DCB- 45 DDB-LAA -G07
Example Ordering Data:
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
MODEL NUMBERGRM2xS-x-75xxx-75xxxGRM2xS-x-45xxx-45xxxGRM2xS-x-22xxx-22xxxLETTER
DIMB4
F1 MAXF2 MIN
J1J7J14J16M1
mm168,543,030,087,459,543,727,0135,5
JAW PART NUMBERIF ORDERED SEPARATELY
CLAMPSIZE
2JAW
65202-01
REPLACEMENT KIT NUMBERIF ORDERED SEPARATELY
CLAMPSIZE
2KIT NUMBER
65275-03Kit includes:
1 Jaw Driver Pin1 Pivot Pin4 Slider Bushings1 O-RingO-Ring used with 0° Jaws only
SPECIFICATIONSTOTAL CLAMP FORCE
at 6 barCLAMP SIZE& MODEL
2xS
WEIGHTREDUCER
LENGTHADDER
kg0,30
mm5,0
N645
S1 HEX
T2 J1(OPEN)
B4(OPEN)
JAW PIVOT
J1
M1
B4(CLOSED)
J7
F1 (ADJUSTABLE)
J16(PARALLEL)
J14 JAW PIVOT
NOTE:1) ALL DIMENSIONS ARE REFERENCE UNLESS SPECIFICALLY TOLERENCED
GRM2TS-6-45-45 SHOWN
9
GENERAL OPTIONS: CLAMP ACCESSORIES
G07 ALUMINUM JAW CLAMP(JAW A ROTATES ONLY)
This option provides a GRM clamp with hardcoated aluminumjaws that reduce the weight of the clamp by 0,3 kg. Both jaws acceptall Series GRM standard and accessory tips. Jaw rotations are thesame as standard GRM clamps. Consult PHD for additional accessorycompatibility. Not available with G01 and G02 options.
No-ear impact plates are standard with this option.Available on size 2.
ROTATIONLETTER
DIMB4J1J6J14J15S1T2
75° x 00° 45° x 00° 22° x 00°mm
168,598,174,024,147,3—
48,8
mm168,589,064,824,138,05,036,2
mm168,576,852,724,127,65,019,6
Example Ordering Data:
MODEL NUMBERGRM2xS-x-75xxx-00xxxGRM2xS-x-45xxx-00xxxGRM2xS-x-22xxx-00xxxLETTER
DIMB4
F1 MAXF2 MIN
J1J7J14J16M1
mm168,543,030,067,859,524,127,0135,5
JAW PART NUMBERIF ORDERED SEPARATELY
CLAMPSIZE
2JAW
65241-01
REPLACEMENT KIT NUMBERIF ORDERED SEPARATELY
CLAMPSIZE
2KIT NUMBER
65275-03Kit includes:
1 Jaw Driver Pin1 Pivot Pin4 Slider Bushings1 O-RingO-Ring used with 0° Jaws only
SPECIFICATIONSTOTAL CLAMP FORCE
at 6 barCLAMP SIZE& MODEL
2xS
WEIGHTREDUCER
LENGTHADDER
kg0,30
mm5,0
N645
GRM2T S -6- 45 DCB- 00 DDB-LAA -G07
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
GRM2TS-6-45-00 SHOWN
J14
J1J16(PARALLEL)
M1
J7
B4(CLOSED)
F1(ADJUSTABLE)
JAW PIVOT
S1 HEX
GRM2TS-6-45-00 SHOWN
JAW PIVOT
J14
T2J1
(OPEN)
B4(OPEN)
J6(OPEN)
J15(OPEN)
NOTE:1) ALL DIMENSIONS ARE REFERENCE UNLESS SPECIFICALLY TOLERENCED
10
G08
GENERAL OPTIONS: CLAMP ACCESSORIES
LIFTING JAWSG09orThese options provide standard jaws with special cam slots
that increase the clamp’s ability to pick up heavier loads as the jawsbegin to close. Both jaws accept all Series GRM standard andaccessory tips. These jaws have shorter locking ramps and require adifferent tip color code versus material thickness (see chart below).New red tips replace gold tips for panel thickness of 2,5 - 3,5 mmfor this accessory only. G08 jaws (colored gold) open a maximumof 45° and have the greatest lifting ability. G09 jaws (colored silver)open a maximum of 75° with more lifting ability than the standard Sjaw style.
Available on size 2.
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
GRM2T S -6- 75 DCB- 75 DDB-LAA -G08
Example Ordering Data:
LETTER DIM.B4 (OPEN)J1 (OPEN)J6 (OPEN)
S1T2T3
G08mm
140,8122,061,05,0
65,632,8
G09mm
112,7138,369,1—
87,743,9
RECOMMENDED TIP COMBINATIONSJAW TIP OPTIONS - JAW A OR B
MATERIAL THICKNESS0 to 1,5 to 2,5 to
1,5 mm 2,5 mm 3,5 mmColor Black Silver RedNo tip Blank Blank BlankSingle Cone Point SCB SCS SCRDouble Cone Point DCB DCS DCRSingle Diamond Point SDB SDS SDRDouble Diamond Point DDB DDS DDRSingle Urethane Pad SUB SUB SUBDouble Urethane Pad DUB DUB DUB
CLAMP SIZE& OPTIONSGRM2-G08GRM2-G09
GRM2-B08-G08GRM2-B08-G09
SPECIFICATIONSLIFTING FORCE
AT 6 barN894915593
COLOREDGOLD COLORED
SILVER
GRMxxS-6-45xxx-45xxx-G08GRMxxS-6-22xxx-22xxx-G08
GRMxxS-6-75xxx-75xxx-G09GRMxxS-6-45xxx-45xxx-G09GRMxxS-6-22xxx-22xxx-G09
J6(OPEN)
T3
T2 J1(OPEN)
JAWPIVOT
B4(OPEN)
NOTE:1) ALL DIMENSIONS ARE REFERENCE UNLESS SPECIFICALLY TOLERANCED.
OPTIONG08G09
PART NUMBER65268-0265269-02
SPECIAL JAW PART NUMBERSIF ORDERED SEPARATELY
ROTATION22° x 22°, 45° x 45°
22° x 22°, 45° x 45°, 75° x 75°
B4(OPEN)
J1(OPEN)
T2
T3J6
(OPEN)
JAWPIVOT
S1 HEX
G08 SHOWN
11
H13
IMPACT PLATE OPTION: CLAMP ACCESSORIES
This option provides an impact plate mounted below the switchhousing of Pxxxx or Dxxxx options. The impact plate protrudes pastthe face of the switch housing protecting it from damage. No-earimpact plates are standard with this option.
The H13 option is not required when ordering the Kxxxx option(impact plates are standard with this option).
Available on size 2.
IMPACT PLATE OPTION FORPxxxx OR Dxxxx
CLAMPSIZE
2ACCESSORY
H13
GRM2TS-6-45DCB-45DDB-LAA -H13 -P3D00
Example Ordering Data:
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
RETRACTED POSITION
45,3 MAX
33,6
ADJUSTMENT DIRECTION
PANEL PRESENT
LEVER
POSITION
1
2
3
4
5
6
7
EXTENDED POSITION
JAW A
38,4 MIN
33,6
JAW B
SWITCH CABLEEXIT LOCATION(P3xxx AND D3xxxSHOWN)
5,6
ADJUSTMENT DIRECTION
PANEL PRESENT
LEVER
POSITION
1
2
3
4
5
6
7
59,7
29,8
3
4
1
2
37,1
72,0
REPLACEMENT KIT NUMBERIF ORDERED SEPARATELY
Kit Includes:1 Impact Plate
NOTES:1) ALL DIMENSIONS ARE REFERENCE ONLY UNLESS
SPECIFICALLY TOLERENCED2) NUMBERS IN CIRCLES INDICATE POSITION (POSITION 1
IS PORT SIDE OF CLAMP)
H13-P3Dxx SHOWN
12
JB03x
JAW OPTIONS: CLAMP ACCESSORIES
SWITCH MOUNTING JAW CLAMPFOR USE WITH GRM2xM SERIESCLAMPS ONLY
This option provides a lower flat shovel jaw with the ability tomount the S01 switch accessory. It can be ordered with or without aspecially designed double cone point tip. This tip is designed in sucha way that the S01 switch will not give a false reading when there isno panel between the jaws. Also included is a special impact plate thatprotects the switch cable as it is routed away from the switch.
Available on size 2.
GRM2TM-6-85-00-JB031-S01SHOWN
CLAMPSIZE
GRM2
KIT/PARTDESCRIPTIONJaw Kit - No tipTip Kit - BlackTip Kit - SilverTip Kit - Gold
Switch Kit - S01
KIT/PARTNUMBER73068-0373068-0473068-0573068-0665136-11
MATERIALTHICKNESS
—0-1,5 mm
1,51-3,0 mm3,01-4,0 mm
—
GRM2T M -6-85 blank -00-LAA -JB031 -S01
NOTE: JB03x accessory does not include switch.
Example Ordering Data:
ACCESSORYJB030JB031JB032JB033
SHADED CODES are required for this option.
BORDERED CODES will normally be ordered.
All non-bold codes are for example only.
For compatibility with other units, consult PHD.
DESCRIPTIONSwitch ready jaw - No tip included
Switch ready jaw - Black tip includedSwitch ready jaw - Silver tip includedSwitch ready jaw - Gold tip included
22,7 MAX8,0 MIN
1,5DISTANCE FROM SWITCH
FACE TO JAW FACE
72,2
36,1
10,0
85°
45°
22°
13
SWITCH OPTIONS: CLAMP ACCESSORIES
SWITCH INSTALLED - THREADED BARRELPROXIMITY SWITCH WITH QUICK CONNECTS03 S08to
This option mounts either an 8 mm or 12 mm AC or DCproximity switch onto any switch mounting options.
Available on sizes 2 and 4.
SWITCHOPTION
S03S04S05S06S07S08
THREADSIZE
M8 x 1,0M8 x 1,0M8 x 1,0
M12 x 1,0M12 x 1,0M12 x 1,0
REPLACEMENT KIT NUMBERS IF ORDERED SEPARATELYSWITCH
TYPE24 VDC - PNP24 VDC - NPN
AC24 VDC - PNP24 VDC - NPN
AC
BARRELLENGTH40 mm50 mm40 mm40 mm40 mm60 mm
PHD SWITCHNUMBER
65439-00165439-00265439-00365439-00465439-00565439-006
PEPPERL+FUCHSPART NUMBER
NBB2-8GM40-E2-Y906140NBB1.5-8GM50-E0-Y906141NJ1.5-8GM40-WS-Y906241NBB2-12GM40-E2-Y906251NBB2-12GM40-E0-Y906261NBB2-12GM60-WS-Y906271
Switches include 2 lock nuts
SWITCHTYPEDCAC
PHD PARTNUMBER
65440-001-0265440-002-02
PEPPERL+FUCHSPART NUMBER
V1-G-YE2M-PVCV12-G-YE2M-PVC
MATCHING CORDSETS 2 METERS LONG
(-)
1 BROWN
4 BLACK
3 BLUE
LOAD
(+)
(-)
L1
2 RED/BLACK
3 RED/WHITE
1 GREEN
N
2-Wire ACAC Normally Open
1 BROWN
4 BLACK
3 BLUE
(+)
3-Wire DCPNP Normally Open
LOAD
LOAD
MATING CORDSET
DC - M12 x 1,0 INTERNAL THREADAC - 1/2-20 INTERNAL THREAD
2 m
LED - YELLOWSIGNAL
LED - YELLOWSIGNAL
LED - REDPOWER (12 mm
PROX ONLY)
Pin 4Black
Pin 1Brown
Pin 3Blue
Pin 2Red/Black
Pin 1Green
Pin 3Red/White
M12 x 1,0 THREAD
1/2-20 THREAD
0,28 m
BARRELLENGTH
0,28 m
DC PROXIMITY SWITCH
AC PROXIMITY SWITCH
GRM2TS-6-45DCB-45DDB-LAA -S03 -SB15Example Ordering Data:
SHADED CODES are required for this option.
BORDERED CODES will normally be ordered.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.3-Wire DC
NPN Normally Open
BARRELLENGTH
14
DOUBLE SHEET DETECTORSB15
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
SB18toThis option provides a method to give a signal when the correct
number of panels are gripped in the jaws. An aluminum housing mountedon the side of the clamp body, accommodates 8 and 12 mm switches. Theswitch senses the position of a target on the drive pin when the jaws areclosed. When adjusted correctly, the switch senses the target when onepanel is gripped between the jaws. When more than one panel is gripped thetarget doesn’t retract as far, the switch gives no signal, and the press can bestopped. This product is not intended to be the primary double sheetdetector, but is a good backup or redundant double sheet detector. Theswitch cover is not available on the port side of the clamp.
Available on size 2. For use with the following customer supplied Pepperl+Fuchsproximity switches or equivalent: (shielded switches only)
8mm = NBB2-8GM40-E2-Y9064108mm = NBB1.5-8GM50-E0-Y9061418mm = NJ1.5-8GM40-WS-Y90624112mm = NBB2-12GM40-E2-Y90625112mm = NBB2-12GM40-E0-Y90626112mm = NBB2-12GM60-WS-Y906271
Kit includes:Housing and all pins and screws requiredfor installation. Switches are not included.
PATENT PENDING
NOTES:1) ALL DIMENSIONS ARE REFERENCE UNLESS SPECIFICALLY TOLERANCED2) NUMBERS IN CIRCLES INDICATE POSITION (POSITION 1 IS PORT SIDE OF CLAMP)
SB15 SHOWN
CLAMPSIZE
22
2xF or 2xK2xF or 2xK
OPTIONSB15, SB16SB17, SB18SB15, SB16SB17, SB18
KITNUMBER65438-0365438-0465438-0565438-06
SWITCHTHREAD SIZE
8 mm12 mm8 mm12 mm
REPLACEMENT KIT NUMBERS IF ORDERED SEPARATELY
GRM2TS-6-45DCB-45DDB-LAA -S03 -SB15Example Ordering Data:
ACCESSORYSB15SB16SB17SB18
SWITCHTHREAD SIZE
881212
SWITCHPOSITION
2424
SHADED CODES are required for this option.
BORDERED CODES will normally be ordered.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
RETRACTED POSITION
43,9 MAX8 mm SWITCH44,9 MIN12 mm SWITCH
33,6MIN
JAW A
JAW B3,0
EXTENDED POSITION
28,4 MIN8 mm SWITCH29,4 MIN12 mm SWITCH
1
2
3
4
27,2
54,5
SWITCH
JAM NUT
25,1 MINTHD
LENGTH
4,0
71,4
29,538,517,5 18,5
15
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
SWITCH INSTALLATION PROCEDURE:1) Thread lock nut (item 3) onto switch (item 2).
2) Loosen cover screws (item 5) and slide cover (item 4) sothat switch mounting thread is directly above the target blade(item 7).
Note: The target blade can be identified by looking into one ofthe switch mounting threads in the cover and locating a raisedblade approximately 4,3 mm wide. If the target blade cannot beseen, loosen the cover screws and slide the cover until the targetblade is centered below the switch mounting thread.
3) Tighten cover screws.
4) Thread switch into threaded hole that faces the target blade.
5) Thread switch until switch bottoms out on target blade.
6) Note orientation of switch and then back it out 1/2 turn to setgap between switch and target blade.
7) Now hold the switch and tighten lock nut against the cover.
8) Use open end wrench to tighten lock nut completely. Do notover tighten.
FIELD SET-UP PROCEDURE:(Tips must be installed on both jaws)
1) Install power supply to switch (item 2). If switch is not installed,refer to switch installation procedure before continuing.
2) Install air lines to clamp (item 1).
3) Insert the material to be clamped between the jaws and actuateclamp until the jaws are in the closed position. The materialacts as a spacer for setting up the position of the target (item 7)in relation to the switch. Keep fingers away from jaws whenactuating clamp.
4) Loosen cover screws (item 5) and slide cover (item 4) towardrear of body (away from jaws) until it stops.
5) Slide the cover toward the jaws until switch signal is on.Continue to slide cover toward jaws another 1,0 mm.
6) Hold cover so it does not slide and tighten cover screwsto 9,6 N-m.
7) Actuate clamp until the jaws are in the open position.
8) Install two pieces of material to be clamped (double sheets)between the jaws and actuate clamp until the jaws are in theclosed position.
9) Switch signal should be off.
10) If the switch signal is still on, actuate clamp until the jaws arein the open position and remove one piece of material.
11) Again, insert one piece of material to be clamped between thejaws and actuate clamp until the jaws are in the closed position.
12) Switch signal should be on.
13) Loosen cover screws and slide cover toward rear of body(away from jaws) until switch signal is off.
14) Slide the cover toward the jaws until switch signal is on.Continue to slide cover toward jaws another 0,8 mm.
15) Hold cover so it does not slide and tighten cover screwsto 9,6 N-m.
16) Repeat steps 7 through 9.
Note: The sensitivity of the switch signal may vary based onthe type of switch used, material thickness, and set-up. ConsultPHD, if you require further assistance.
CHANGING SWITCH POSITION PROCEDURE:(Converting from switch position 2 to 4 or switch position 4 to 2)
1) Remove all air lines connected to clamp (item 1).
2) Loosen lock nut (item 3).
3) Remove switch (item 2) from cover (item 4). Note switchposition.
4) Remove cover screws (item 5), washers (items 6), and cover.Note orientation of target blade (item 7) after cover is removed.
5) Rotate target from present position - 180° about jaw driver pin(item 8).
6) Install cover, washers, and cover screws. Do not tighten screws.
7) Slide cover so that switch mounting thread is directly above thetarget blade.
8) Tighten cover screws.
9) Thread switch into threaded hole that faces the target blade.
10) Thread switch until switch bottoms out on target blade.
11) Note orientation of switch and then back it out 1/2 turn to setgap between switch and target blade.
12) Now hold the switch and tighten lock nut against the cover.
13) Use open end wrench to tighten lock nut completely. Do notover tighten.
ITEM 7
TARGET BLADE
TARGET ORIENTATION SHOWNIS FOR -SB15 AND -SB17(ROTATE 180° FOR -SB16
AND -SB18)
SWITCH POSITIONSHOWN IS FOR-SB15 AND -SB17
SWITCHMOUNTINGTHREAD
SWITCH POSITION FOR-SB16 AND -SB18
SWITCH INSTALLATION AND FIELD SET-UP
1
2
3
45
8
96
7
16
Dxxxx
Kit includes:Housing and all pins and screws requiredfor installation.
D3xxx SHOWN
NOTES:1) ALL DIMENSIONS ARE REFERENCE UNLESS
SPECIFICALLY TOLERANCED2) NUMBERS IN CIRCLES INDICATE POSITION
(POSITION 1 IS PORT SIDE OF CLAMP)
ADJUSTMENT DIRECTION
DOUBLE SHEET LEVER
POSITION
TARGET - SOLD WITH KIT
ASSEMBLY NOTE: Notch intarget to face switch.
CLAMPSIZE
2
2xF or 2xK
ACCESSORYDxN00DxA00DxB00DxD00DxN00DxA00DxB00DxD00
KITNUMBER71964-0971964-1071964-1771964-1171964-1271964-1371964-1871964-14
DESCRIPTIONHousing w/o switch kitHousing w/4-pin AC/DC switch kitHousing w/3-pin AC/DC switch kitHousing w/4-pin DC switch kitHousing w/o switch kitHousing w/4-pin AC/DC switch kitHousing w/3-pin AC/DC switch kitHousing w/4-pin DC switch kit
35,6
72,0
JAW A
JAW B
SWITCH CABLE EXITLOCATION(D3xxx SHOWN)
38,4 MIN45,3 MAX
5,6
ADJUSTMENT DIRECTION
DOUBLE SHEET
LEVERPOSITION
1
2
3
4
59,7
29,8
GRM2TS-6-45DCB-45DDB-LAA -D 3 A 10Example Ordering Data:
SHADED CODES are required
for this option. All unshaded model codes
are example only.
Switch Option-Refer to page next page forspecifications.Panel Thickness Option-Housing may bepreset at the factory for panel thickness in0,1 mm increments.Material Thickness Range - 0,7 to 4,0 mm
DxA00, DxB00, and DxD00 options do notrequire factory setup. For compatibility withother units, consult PHD.
PANEL THICKNESS OPTION00 - No Panel07 - 0,7 mm10 - 1,0 mm40 - 4,0 mm
SWITCH OPTIONN - No SwitchA - 4-Pin AC/DC SwitchB - 3-Pin AC/DC SwitchD - 4-Pin DC Switch
SWITCH HOUSINGPOSITION
1 - Position 13 - Position 3
HOUSING OPTIOND - Double Sheet
ACCESSORYD3xxx
D1xxx or D3xxxD3xxx
BODY OPTIONSTD
B05, B06, B07, B08, B08A, B09B05, B06, B07, B08, B08A, B09
JAW OPTIONC, D, G, H, J, N, P, S, F, K
C, D, G, H, J, N, P, SF, K
HOUSING POSITION3
1 or 33
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
DOUBLE SHEET DETECTION
Double sheet detection is a process where signaling devices detect thepresence of multiple parts. The Series GRM Clamp accommodates this optionby affixing an adjustable housing and switch to the side of the clamp body. Theinternal switch senses the position of a target on the drive pin that travels inthe housing. The location of the target relates directly to jaw position and thethickness of material being clamped. This option is an excellent choice forbackup or redundant signaling detection and will function within a wide rangeof material thicknesses 0,7 to 4,0 mm. Steel tips are recommended. Urethanetips are not recommended for double sheet detection. Single cone point tosingle diamond tips are not recommended for panels 1,0 mm and below.Single diamond to single diamond tips are recommended for panels 1,0 mmand below.
Available on size 2.
17
FIELD SET-UP PROCEDURE:1) Using pressure, close clamp jaws with one panel between tips.
2) Loosen both screws and remove lever from locating hole.
3) Slide housing in direction of arrow (toward jaws) until switchjust turns on.
4) Snug flat washer screw. The housing should still slide back andforth.
5) Rotate lever into hole that matches present housing locationand snug screw.
6) Wiggle housing forward and backward. If switch flickers off andon, rotate the lever into the next hole with a higher number (i.e.,from 2 to 3). Wiggle housing again. Switch should stay on.
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
If not, continue to higher numbered hole until switch does notflicker.
7) Tighten both screws to 9,6 Nm. Switch is now set.
TO TEST THE SETUP:
1) Using pressure, close clamp jaws with one panel between tips.The switch should stay on.
2) Close clamp jaws with two panels between tips. The switchshould turn off.
NOTE: With no panel present, the switch will turn on and remain onas the target passes under the switch.
2
3 1
4
LOAD
L2L1
±
±
BU
BN
1LOAD
L2
L1RD/BK
RD/WH
GN
LOAD
+
-
BN
BK
BU
0,2 m 39,0
1/2-20 UNFMICROFAST CONNECTOR
3 2
1
2 3
4
0,2 m 40,0
M12 x 1EUROFAST CONNECTOR
1/2-20 UNFMICROFAST CONNECTOR
0,2 m 40,0
WARNING: NO SHORT-CIRCUITPROTECTION. ALWAYS WIRE A LOADIN SERIES WITH THE SENSOR
WARNING: NO SHORT-CIRCUITPROTECTION. ALWAYS WIRE A LOADIN SERIES WITH THE SENSOR
SHORT CIRCUIT AND OVERLOADPROTECTION
SWITCH OPTION A
SWITCH OPTION B
SWITCH OPTION D
Bi 2-Q10S-AZ31X-0.2M-SB 4T/S1597
Bi 2-Q10S-AP6X-0.2M-RS 4T
Bi 2-Q10S-AZ31X-0.2M-SB 3T
SWITCHOPTION
ABD
SWITCHTYPE
4-PIN AC/DC - N.O.3-PIN AC/DC - N.O.
4-PIN DC - N.O. - PNP
PHD SWITCHNUMBER
72121-00172121-00372121-002
TURCK PART NUMBERBi 2-Q10S-AZ31X-0.2M-SB 4T/S1597
Bi 2-Q10S-AZ31X-0.2M-SB 3TBi 2-Q10S-AP6X-0.2M-RS 4T
REPLACEMENT KIT NUMBERS IF ORDERED SEPARATELY
18
Pxxxx
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
PANEL PRESENT DETECTION
Panel present detection is a process where signaling devices detect thepresence of a part. The Series GRM Clamp accommodates this option by affixingan adjustable housing and switch to the side of the clamp body. The internal switchsenses the position of a target on the drive pin that travels in the housing. Thelocation of the target relates directly to jaw position and the thickness of materialbeing clamped. This option is an excellent choice for panel present detection andwill function within a wide range of material thicknesses 0,7 to 4,0 mm. Steel tipsare recommended. Urethane tips are not recommended for panel presentdetection. Single cone point to single diamond tips are not recommended forpanels 1,0 mm and below. Single diamond to single diamond tips arerecommended for panels 1,0 mm and below.
Available on size 2.
Kit includes:Housing and all pins and screws requiredfor installation.
P3xxx SHOWN
NOTES:1) ALL DIMENSIONS ARE REFERENCE UNLESS
SPECIFICALLY TOLERANCED2) NUMBERS IN CIRCLES INDICATE POSITION
(POSITION 1 IS PORT SIDE OF CLAMP)
GRM2TS-6-45DCB-45DDB-LAA -P 3 A 10Example Ordering Data:
SHADED CODES are required
for this option. All unshaded model codes
are example only.
Switch Option-Refer to next page forspecifications.Panel Thickness Option-Housing may bepreset at the factory for panel thickness in0,1 mm increments.Material Thickness Range -0,7 to 4,0 mm
PxA00, PxB00, and PxD00 options do notrequire factory setup. For compatibilitywith other units, consult PHD.
ADJUSTMENT DIRECTION
PANEL PRESENT LEVER
POSITION
PANEL THICKNESS OPTION00 - No Panel07 - 0,7 mm10 - 1,0 mm40 - 4,0 mm
SWITCH OPTIONN - No SwitchA - 4-Pin AC/DC SwitchB - 3-Pin AC/DC SwitchD - 4-Pin DC Switch
SWITCH HOUSINGPOSITION
1 - Position 13 - Position 3
HOUSING OPTIONP - Panel Present
ACCESSORYP3xxx
P1xxx or P3xxxP3xxx
BODY OPTIONSTD
B05, B06, B07, B08, B08A, B09B05, B06, B07, B08, B08A, B09
JAW OPTIONC, D, G, H, J, N, P, S, F, K
C, D, G, H, J, N, P, SF, K
HOUSING POSITION3
1 or 33
CLAMPSIZE
2
2xF or 2xK
ACCESSORYPxN00PxA00PxB00PxD00PxN00PxA00PxB00PxD00
KITNUMBER71964-0371964-0471964-1571964-0571964-0671964-0771964-1671964-08
DESCRIPTIONHousing w/o switch kitHousing w/4-pin AC/DC switch kitHousing w/3-pin AC/DC switch kitHousing w/4-pin DC switch kitHousing w/o switch kitHousing w/4-pin AC/DC switch kitHousing w/3-pin AC/DC switch kitHousing w/4-pin DC switch kit
1
2
3
4
59,7
29,8
JAW A
JAW B
SWITCH CABLE EXITLOCATION(P3xxx SHOWN)
38,4 MIN45,3 MAX
5,6
ADJUSTMENT DIRECTION
PANEL PRESENT
LEVERPOSITION
35,6
72,0
19
FIELD SET-UP PROCEDURE:1) Using air pressure, close clamp jaws with panel between tips.
2) Loosen both screws and remove lever from locating hole.
3) Slide housing in direction of arrow (toward cylinder) untilswitch just turns on.
4) Snug flat washer screw. Housing should still slide back andforth.
5) Rotate lever into hole that matches present housing locationand snug screw.
6) Wiggle housing forward and backward. If switch flickers off andon, rotate the lever into the next hole with a lower number (i.e.,from 5 to 4). Wiggle housing again. Switch should stay on. Ifnot, continue to lower numbered hole until switch does notflicker.
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
7) Tighten both screws to 9,6 Nm. Switch is now set.
TO TEST THE SETUP:
1) Using air pressure, close clamp jaws with panel between tips.The switch should stay on.
2) Close clamp jaws with no panel between tips. The switchshould turn off.
NOTE: With no panel present, the switch will flicker on as the targetpasses under the switch and turn off as the jaws reach full closed.
For panels 0,7 mm and below, it may be necessary to set the switchin the first hole that flickers (see note 6). Do not rotate lever into thenext hole with a lower number. Instead, leave the lever in the samehole and slide the housing in the direction of the cylinder so theswitch stays on and tighten both screws.
2
3 1
4
LOAD
L2L1
±
±
BU
BN
1LOAD
L2
L1RD/BK
RD/WH
GN
LOAD
+
-
BN
BK
BU
0,2 m 39,0
1/2-20 UNFMICROFAST CONNECTOR
3 2
1
2 3
4
0,2 m 40,0
M12 x 1EUROFAST CONNECTOR
1/2-20 UNFMICROFAST CONNECTOR
0,2 m 40,0
WARNING: NO SHORT-CIRCUITPROTECTION. ALWAYS WIRE A LOADIN SERIES WITH THE SENSOR
WARNING: NO SHORT-CIRCUITPROTECTION. ALWAYS WIRE A LOADIN SERIES WITH THE SENSOR
SHORT CIRCUIT AND OVERLOADPROTECTION
SWITCH OPTION A
SWITCH OPTION B
SWITCH OPTION D
Bi 2-Q10S-AZ31X-0.2M-SB 4T/S1597
Bi 2-Q10S-AP6X-0.2M-RS 4T
Bi 2-Q10S-AZ31X-0.2M-SB 3T
SWITCHOPTION
ABD
SWITCHTYPE
4-PIN AC/DC - N.O.3-PIN AC/DC - N.O.
4-PIN DC - N.O. - PNP
PHD SWITCHNUMBER
72121-00172121-00372121-002
TURCK PART NUMBERBi 2-Q10S-AZ31X-0.2M-SB 4T/S1597
Bi 2-Q10S-AZ31X-0.2M-SB 3TBi 2-Q10S-AP6X-0.2M-RS 4T
REPLACEMENT KIT NUMBERS IF ORDERED SEPARATELY
20
Kxxxx
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
PANEL PRESENT ANDDOUBLE SHEET DETECTION
This option provides panel present and double sheet detectionon one Series GRM clamp. This is accomplished by affixing twoadjustable housings and switches to the sides of the clamp body. Theinternal switches sense the position of the targets on the drive pinthat travels in the housings. The location of the targets relates directlyto jaw position and the thickness of the material being clamped. Thisoption is an excellent choice for panel present detection and backupor redundant signaling detection. This option will also function withina wide range of material thicknesses 0,7 to 4,0 mm. Steel tips arerecommended. Urethane tips are not recommended for panelpresent and double sheet detection. Single cone point to singlediamond tips are not recommended for panels 1,0 mm and below.Single diamond to single diamond tips are recommended forpanels 1,0 mm and below.
Available on size 2.
Specific body options are required for this option. See thechart below for available bodies.
Kit includes:Housings and all pins and screwsrequired for installation.
-B06-K3xxx SHOWN
74,2
37,1
72,0
ADJUSTMENT DIRECTION
PANEL PRESENT
LEVERPOSITION
1 64
2 75
3
JAW A
JAW B
SWITCH CABLEEXIT LOCATION
38,4 MIN
33,65,6
29,8
59,7
29,8
59,7ADJUSTMENT DIRECTION
DOUBLE SHEET
LEVERPOSITION
164
275
3
JAW A
JAW B
SWITCH CABLEEXIT LOCATION
45,3 MAX
33,6
GRM2TS-6-45DCB-45DDB-LAA-B06 -K 3 A 10Example Ordering Data:
SHADED CODES are required
for this option. All unshaded model codes
are example only.
PANEL THICKNESS OPTION00 - No Panel07 - 0,7 mm10 - 1,0 mm40 - 4,0 mm
SWITCH OPTIONN - No SwitchA - 4-Pin AC/DC SwitchB - 3-Pin AC/DC SwitchD - 4-Pin DC Switch
PANEL PRESENT SWITCHHOUSING POSITION
1 - Position 13 - Position 3
HOUSING OPTIONK - Panel Present and
Double Sheet
ACCESSORYK1Nxx or K3NxxK1xxx or K3xxx
BODY OPTIONB05, B06, B07, B08, B08A, B09B05, B06, B07, B08, B08A, B09
JAW OPTIONC, D, G, H, J, N, P, SC, D, G, H, J, N, P, S
HOUSING POSITION1 and 31 and 3
CLAMPSIZE
2
ACCESSORYKxN00KxA00KxB00KxD00
KITNUMBER71964-1971964-2071964-2271964-21
DESCRIPTIONHousings w/o switch kitHousings w/4-pin AC/DC switch kitHousings w/3-pin AC/DC switch kitHousings w/4-pin DC switch kit
Switch Option - Refer to next page forspecifications.Panel Thickness Option - Housings may bepreset at the factory for panel thickness in0,1 mm increments.Material Thickness Range - 0,7 to 4,0 mm
K1x00 and K3x00 options do not requirefactory setup. For compatibility with otherunits, consult PHD.
NOTE:1) ALL DIMENSIONS ARE REFERENCE
UNLESS SPECIFICALLY TOLERANCED
21
PANEL PRESENT DETECTION FIELDSET-UP PROCEDURE1) Using air pressure, close clamp jaws with panel between tips.2) Loosen both screws and remove lever from locating hole.3) Slide housing in direction of arrow (toward cylinder) until switch just
turns on.4) Snug flat washer screw. Housing should still slide back and forth.5) Rotate lever into hole that matches present housing location and snug screw.6) Wiggle housing forward and backward. If switch flickers off and on, rotate
the lever into the next hole with a lower number (i.e., from 5 to 4). Wigglehousing again. Switch should stay on. If not, continue to lower numberedhole until switch does not flicker.
7) Tighten both screws to 9,6 Nm. Switch is now set.TO TEST THE SETUP:1) Using air pressure, close clamp jaws with panel between tips. The switch
should stay on.2) Close clamp jaws with no panel between tips. The switch should turn off.NOTE: With no panel present, the switch will flicker on as the target passesunder the switch and turn off as the jaws reach full closed. For panels 0,7 mmand below, it may be necessary to set the switch in the first hole that flickers(see note 6). Do not rotate lever into the next hole with a lower number.Instead, leave the lever in the same hole and slide the housing in thedirection of the cylinder so the switch stays on and tighten both screws.
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
DOUBLE SHEET DETECTION FIELDSET-UP PROCEDURE1) Using pressure, close clamp jaws with one panel between tips.2) Loosen both screws and remove lever from locating hole.3) Slide housing in direction of arrow (toward jaws) until switch just turns on.4) Snug flat washer screw. The housing should still slide back and forth.5) Rotate lever into hole that matches present housing location and snug
screw.6) Wiggle housing forward and backward. If switch flickers off and on, rotate
the lever into the next hole with a higher number (i.e., from 2 to 3).Wiggle housing again. Switch should stay on. If not, continue to highernumbered hole until switch does not flicker.
7) Tighten both screws to 9,6 Nm. Switch is now set.TO TEST THE SETUP:1) Using pressure, close clamp jaws with one panel between tips. The switch
should stay on.2) Close clamp jaws with two panels between tips. The switch should turn off.NOTE: With no panel present, the switch will turn on and remain on as thetarget passes under the switch.
2
3 1
4
LOAD
L2L1
±
±
BU
BN
1LOAD
L2
L1RD/BK
RD/WH
GN
LOAD
+
-
BN
BK
BU
0,2 m 39,0
1/2-20 UNFMICROFAST CONNECTOR
3 2
1
2 3
4
0,2 m 40,0
M12 x 1EUROFAST CONNECTOR
1/2-20 UNFMICROFAST CONNECTOR
0,2 m 40,0
WARNING: NO SHORT-CIRCUITPROTECTION. ALWAYS WIRE A LOADIN SERIES WITH THE SENSOR
WARNING: NO SHORT-CIRCUITPROTECTION. ALWAYS WIRE A LOADIN SERIES WITH THE SENSOR
SHORT CIRCUIT AND OVERLOADPROTECTION
SWITCH OPTION A
SWITCH OPTION B
SWITCH OPTION D
Bi 2-Q10S-AZ31X-0.2M-SB 4T/S1597
Bi 2-Q10S-AP6X-0.2M-RS 4T
Bi 2-Q10S-AZ31X-0.2M-SB 3T
SWITCHOPTION
ABD
SWITCHTYPE
4-PIN AC/DC - N.O.3-PIN AC/DC - N.O.
4-PIN DC - N.O. - PNP
PHD SWITCHNUMBER
72121-00172121-00372121-002
TURCK PART NUMBERBi 2-Q10S-AZ31X-0.2M-SB 4T/S1597
Bi 2-Q10S-AZ31X-0.2M-SB 3TBi 2-Q10S-AP6X-0.2M-RS 4T
REPLACEMENT KIT NUMBERS IF ORDERED SEPARATELY
22
PSxxx
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
POSITIONAL SENSING DETECTION
This option provides jaw open and jaw closed sensing byaffixing an aluminum housing to the side of the clamp body. Theadjustable switches sense the position of a target on the drive pin asthe clamp opens and closes.
For use with the following PHD or customer supplied switchesor equivalent:
Ni 2-Q6.5-ADZ32-0.16-FSB 5.4X4/S304 (Turck)NBN2-F581-160S6-E8-V1 (P + F)Ni 2-Q6.5-0.16-BDS-2AP6X3-H1141/S34 (Turck)Available on size 2.
(continued on other side -Switch Option specifications)
PS3D9 SHOWN
GRM2TS-6-45DCB-45DDB-LAA -PS 3 D 9Example Ordering Data:
SHADED CODES are required
for this option. All unshaded model codes
are example only.
CONNECTOR POSITION1 - Parallel to bore9 - Perpendicular to bore
SWITCH OPTIONN - No SwitchA - 5-pin AC/DC SwitchD - 4-pin DC Switch (P+F)E - 4-pin DC Switch (Turck)
SWITCH HOUSINGPOSITION
1 - Position 13 - Position 3
HOUSING OPTIONPS - Positional Sensing
NOTES:1) ALL DIMENSIONS ARE REFERENCE UNLESS
SPECIFICALLY TOLERANCED2) NUMBERS IN CIRCLES INDICATE POSITION
(POSITION 1 IS PORT SIDE OF CLAMP)
90°
-PSxA1 = 1/2-20 UNF CABLE CONNECTION-PSxD1 = M12 x 1 CABLE CONNECTION-PSxE1 = M12 x 1 CABLE CONNECTION
39,0
39,2
7,3-PSxD9 = M12 x 1 CABLE CONNECTION-PSxE9 = M12 x 1 CABLE CONNECTION
JAW A
JAW B 4,0 HEXCLOSE SWITCH(ADJUSTABLE)
4,0 HEXOPEN SWITCH (ADJUSTABLE)
4,0 HEX
LEDGREEN = POWERRED & YELLOW = SIGNAL
5,0 HEX
39,0
5,6
29,8
59,7
2
1
4
3
Switch Option-Refer to next pagefor specifications.Connector Position--PSxA1, -PSxD1, and -PSxE1options not recommended for usewith C mounts.Connector position 1 will limitrotation about the clamp body forthe following mounts: R, S, and W.
ACCESSORYPS3NxPSxNxPS3NxPS3A1PSxA1PS3A1PS3DxPSxDxPS3DxPS3ExPSxExPS3Ex
BODY OPTIONSTD
B05, B06, B07, B08, B09B05, B06, B07, B08, B09
STDB05, B06, B07, B08, B09B05, B06, B07, B08, B09
STDB05, B06, B07, B08, B09B05, B06, B07, B08, B09
STDB05, B06, B07, B08, B09B05, B06, B07, B08, B09
JAW OPTIONC, D, G, H, J, N, P, S, F, K
C, D, G, H, J, N, P, SF, K
C, D, G, H, J, N, P, S, F, KC, D, G, H, J, N, P, S
F, KC, D, G, H, J, N, P, S, F, K
C, D, G, H, J, N, P, SF, K
C, D, G, H, J, N, P, S, F, KC, D, G, H, J, N, P, S
F, K
HOUSING POSITION3
1 or 333
1 or 333
1 or 333
1 or 33
23
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
FIELD SET-UP PROCEDURE:1) Using air pressure, close clamp jaws with panel between tips.
2) Loosen but do not remove screw adjacent to letter “C” (close)on switch cover.
3) Slide screw in direction opposite to arrow (toward cylinder)until switch turns off.
4) Slide screw in direction of arrow (toward jaws) until switchturns on.
5) Align washer under head of screw to cover slot on switch coverbefore tightening.
6) Tighten screw to 5,0 Nm. Close switch is now set.
7) Using air pressure, open clamp jaws.
8) Loosen but do not remove screw adjacent to letter “O” (open)on switch cover.
9) Slide screw in direction opposite to arrow (toward jaws) untilswitch turns off.
10) Slide screw in direction of arrow (toward cylinder) until switchturns on.
11) Align washer under head of screw to cover slot on switch coverbefore tightening.
12) Tighten screw to 5,0 Nm. Open switch is now set.
TO TEST THE SETUP:
13) Using air pressure, close clamp jaws with panel between tips.The switch should turn on.
14) Using air pressure, open clamp jaws. The switch should turn on.
Ni 2-Q6.5-ADZ32-0.16-FSB 5.4X4/S304
NBN2-F581-160S6-E8-V1
12
34
LOAD 1RD/WH RD/BK
LOAD 2RD
L1
L1
5
RD/YE
L2
L2
GN
1
2 3
4 LOAD 1
+
–
BN
BK
BU
LOAD 2WH
47,0
23,0
18,0
1/2-20 UNF
THRU HOLE FOR M5 x 0,8 SHCS4,0 HEX
23,5
SO1
SO2
LEDsGREEN: POWER
YELLOW: OUTPUT STATUS (S01)RED: OUTPUT STATUS (S02)
M12 x 1
LEDsGREEN: POWER
YELLOW: OUTPUT STATUS (S1)RED: OUTPUT STATUS (S2)
THRU HOLE FOR M5 x 0,8 SHCS4,0 HEX
23,5
47,0
18,0
18,0
CONNECTORPOSITION 9
CONNECTORPOSITION 1
90°
23,5
LEDsGREEN: POWER
YELLOW: OUTPUT STATUS (S01)RED: OUTPUT STATUS (S02)
THRU HOLE FOR M5 x 0,8 SHCS4,0 HEX
M12 x 1
47,0
18,0
18,1
CONNECTORPOSITION 9
CONNECTORPOSITION 1
90°
SWITCH OPTION A
SWITCH OPTION D
SWITCH OPTION E
PNP DUAL NORMALLY OPEN3-WIRE DC
4-WIRE AC/DC
PNP DUAL NORMALLY OPEN
3-WIRE DC (V1 TYPE)
1
2 3
4 LOAD 1
+
–
BN
BK
BU
LOAD 2WH
Ni 2-Q6.5-0.16-BDS-2AP6X3-H1141/S34
24
SWITCH MOUNTING OPTIONS: CLAMP ACCESSORIES
CLAMPSIZE ACCESSORY
PSxNxPSxA1PSxDxPSxExPSxNxPSxA1PSxDxPSxEx
KITNUMBER72914-0372914-0772914-0472914-0972914-0572914-0872914-0672914-10
DESCRIPTIONHousing w/o switch kit
Housing w/5-pin AC/DC switch kitHousing w/4-pin DC (P+F) switch kit
Housing w/4-pin DC (Turck) switch kitHousing w/o switch kit
Housing w/5-pin AC/DC switch kitHousing w/4-pin DC (P+F) switch kit
Housing w/4-pin DC (Turck) switch kit
SWITCHOPTION
ADE
SWITCHTYPE
5-PIN AC/DC-N.O.4-PIN DC - N.O. - PNP4-PIN DC-N.O. - PNP
PHD SWITCHKIT NUMBER
72914-1172914-1272914-13
SWITCH PART NUMBERNi 2-Q6.5-ADZ32-0.16-FSB 5.4X4/S304
NBN2-F581-160S6-E8-V1Ni 2-Q6.5-0.16-BDS-2AP6X3-H1141/S34
REPLACEMENT SWITCH KIT NUMBERS IF ORDERED SEPARATELY
SWITCHOPTION
ADE
PHD PARTNUMBER
73317-00-0265440-001-0265413-00-02
CORDSETPART NUMBER
KB 5T-2V1-G-YE2M-PVC
RK 4T-2
MATCHING CORDSETS 2 METERS LONG
MATING CORDSET
DC - M12 x 1,0 INTERNAL THREADAC - 1/2-20 INTERNAL THREAD
2 m
Kit includes:Housing and all pins and screws requiredfor installation.
2
2xF or 2xK
REPLACEMENT KIT NUMBERS IF ORDERED SEPARATELY
25
TIP OPTIONS: CLAMP ACCESSORIES
HARD URETHANE TIPSA ON JAW A, B ON JAW B
This option provides harder urethane tips. They are madefrom 93 Durometer Shore A colored red and 85 Durometer Shore Acolored blue for easy identification. These tips provide greaterresistance to panel slippage and more resistance to wear than ourstandard 75 Durometer black tips (DUB or SUB). All dimensions andmounting hardware are identical to the standard urethane tips. Thesetips accommodate 0 to 3,0 mm material thickness on all jaw styles,except on flange jaws. See material thickness chart below.
Tx040 to Tx041
Tx066 to Tx068
Example Ordering Data:
A tip must be specified for jaw A and jaw B.
AVAILABLE ON
GRM4
GRM4GRM2
ACCESSORYTA040 or TB040TA066 or TB066TA040 or TB040TA041 or TB041TA067 or TB067TA041 or TB041TA068 or TB068
GRM2
GRM2
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
GRM2TS-6-45 blank -45 blank -LAA -TA041 -TB041
ACCESSORYCODE
Tx040, Tx041,Tx066, Tx067,
& Tx068
GRM2xS
0 to 3,0
GRMxC
0 to 3,0
GRMxD
0 to 3,0
GRMxF
0 to 2,0
MATERIAL THICKNESS (mm)
SINGLE URETHANE PAD(HARD)
Tx040 (RED)Tx066 (BLUE)
OPTIONTx040Tx040Tx041Tx041Tx066Tx067Tx068
TIP COLORredredredredblueblueblue
KIT NO.65163-0365163-0565163-0465163-0665163-0765163-0865174-05
DOUBLE URETHANE PAD(HARD)
Tx041 (RED)Tx067 (BLUE)
Kit includes:1 Hard Urethane Tip1 Mounting Screw
KIT NUMBERS IF ORDERED SEPARATELYSTYLEsinglesingledoubledoublesingledouble
rounded
ROUNDED URETHANE PAD(HARD)
Tx068 (BLUE)
SIZE2424222
DUROMETER93 Shore A93 Shore A93 Shore A93 Shore A85 Shore A85 Shore A85 Shore A
26
TIP OPTIONS: CLAMP ACCESSORIES
SHARP DOUBLE CONE POINT TIPA ON JAW A, B ON JAW B
Sharp cone points have a tip that is very sharp (less than0,4 mm). They should be used with a double diamond tip (DDB,DDS, or DDG) mounted opposite them or a chisel or shovel jaw.
Tips should be specified (black, silver, or gold) for the materialthickness and jaw style. Sharp cones can be used on jaw A or jaw B.
Available on size 2.
Tx063 to Tx065
GRM2S S -6-45 blank -45 blank -LAA -TA063 -TB063
Example Ordering Data:
SHADED CODES are required for this option.
BORDERED CODES will normally be ordered.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
For simplicity, these tables show the sharp cone point tip on jaw A.
If sharp cones are ordered on Jaws A & B, they will be mounted as shown.
CLAMPSIZE
2063
71231-03064
71231-04065
71231-05
Kit includes:1 Tip1 Mounting Screw
CODE TA OR TB KIT NOS.
REPLACEMENT KIT NUMBERSIF ORDERED SEPARATELY
TIPCODE
TADDx
CLAMPSIZE
2
JAWAB
MATERIAL THICKNESS (mm)STANDARD JAW STYLETIP
CODETA
DDx
0 to1,50063DDB
1,51 to3,00064DDS
3,01 to4,00065DDG
JAWAB
FLANGE JAW STYLE0 to0,85063DDB
0,86 to1,2064DDB
1,21 to1,52065DDB
MATERIAL THICKNESS (mm)1,53 to
1,94064DDS
1,95 to2,29065DDS
2,30 to2,6065DDG
RECOMMENDED TIP COMBINATION
CLAMPSIZE
2
JAW A
JAW B
TA(B)063 = blackTA(B)064 = silverTA(B)065 = gold
27
Tx071
TIP OPTIONS: CLAMP ACCESSORIES
15° SINGLE OR DOUBLE DIAMOND TIPA ON JAW A, B ON JAW B
This option provides single or double diamond tips with thegripping surface on a 15° angle. The tips can be used to grip angledsurfaces while keeping the clamp parallel, decreasing the spacerequired by the clamp. These tips are a set and must be used asa pair.
Tx071 to Tx082 accessories are only available for GRM2xKand GRM2xS clamps.
Available on size 2.
Tx082to
Tx071 TO Tx076
Tx077 TO Tx082
REPLACEMENT KIT NUMBERSIF ORDERED SEPARATELY
CLAMPSIZE
222222
OPTIONTx071, Tx074Tx072, Tx075Tx073, Tx076Tx077, Tx080Tx078, Tx081Tx079, Tx082
STYLEsinglesinglesingledoubledoubledouble
TIPCOLORblacksilvergoldblacksilvergold
KITNUMBER71229-0371229-0471229-0571229-0671229-0771229-08
Kit includes:1 15° Single or Double Diamond Tip1 Mounting Screw
NOTE:1) ALL DIMENSIONS ARE REFERENCE
UNLESS SPECIFICALLY TOLERANCED.
SINGLE DIAMOND TIP
DOUBLE DIAMOND TIP
19,0
24,1
5,0 HEX
19,0
38,9
5,0 HEX
GRM 2 TS-6-45 blank -45 blank -LAA -TA071 -TB071
Example Ordering Data:
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
PART
JAW A
JAW B
15°
UPWARD MOUNTINGSINGLE DOUBLE
TA071/TB071 = black TA077/TB077 = blackTA072/TB072 = silver TA078/TB078 = silverTA073/TB073 = gold TA079/TB079 = gold
DOWNWARD MOUNTINGSINGLE DOUBLE
TA074/TB074 = black TA080/TB080 = blackTA075/TB075 = silver TA081/TB081 = silverTA076/TB076 = gold TA082/TB082 = gold
6,0
FOR K AND S JAW STYLES ONLY
TIP OPTIONTA071/TB071TA072/TB072TA073/TB073TA074/TB074TA075/TB075TA076/TB076TA077/TB077TA078/TB078TA079/TB079TA080/TB080TA081/TB081TA082/TB082
MATIERIALTHICKNESS (mm)
0-1,51,51-3,03,01-4,0
0-1,51,51-3,03,01-4,0
0-1,51,51-3,03,01-4,0
0-1,51,51-3,03,01-4,0
TIPCOLORblacksilvergoldblacksilvergoldblacksilvergoldblacksilvergold
TIPSTYLEsinglesinglesinglesinglesinglesingledoubledoubledoubledoubledoubledouble
MOUNTINGORIENTATION
upwardupwardupward
downwarddownwarddownward
upwardupwardupward
downwarddownwarddownward
PART
JAW A
JAW B
15°
28
V2
SEAL OPTIONS: CLAMP ACCESSORIES
FLUORO-ELASTOMER SEALS FORFLUID COMPATIBILITY
This option provides a Series GRM Clamp with fluoro-elastomer seals that are compatible with certain fluids. Sealcompatibility should be checked with the fluid manufacturer forproper application. This option is not for high temperatureapplications. Consult PHD Clamp Division for high temperatureapplications.
Available on size 2.
GRM 2 TS-6-45DCB-45DDB-LAA -V2Example Ordering Data:
SHADED CODES are required for this option.
All unshaded model codes are example only.
For compatibility with other units, consult PHD.
KIT NUMBER65498-03
REPLACEMENT KIT NUMBERIF ORDERED SEPARATELYCLAMP SIZE
2
Kit includes:1 Rod Seal1 Piston Seal1 Bore Plug Seal
ROD SEAL
PISTON SEAL
BORE PLUG SEAL
PHD, Inc. PHD GmbH9009 Clubridge Drive Arnold-Sommerfeld-Ring 2
P.O. Box 9070, Fort Wayne, Indiana 46899 U.S.A. D-52499 Baesweiler GERMANYPhone (260) 747-6151 • Fax (260) 747-6754 Phone 02401-805 230 • Fax 02401-805 232
[email protected] • www.phdinc.com [email protected] • www.phd-gmbh.de 1M-A4 2/03 5784