series d dual ferrule instrument tube fittings catalog.pdf · series d dual ferrule instrument tube...
TRANSCRIPT
Series D Dual FerruleInstrument Tube Fittings
®
Fluid Connectors
1865 Route 23 South • P.O. Box 768 • Butler, NJ 07405 • Tel: 973.838.6500 • Fax: 973.838.4888© 2002 Generant Company
www.generant.com
610202_covs.qxd7:802183aa covs.qxd 6/21/10 1:12 PM Page 1
®
Series D
BI-LOK to FEMALE NPT
BI-LOK to MALE NPT
DHATube Stub toMale NPT Adapter Page 11
DCTMale NPT Connector Page 8
DSLBulkheadUnion Elbow Page 20
DCTZThermocouple Connector Page 10
DSCBulkhead MaleNPT Connector Page 19
DLNMale NPT Elbow Page 14
DLFFemale NPT Elbow Page 13
DTFFemale NPT Run Tee Page 22
DTHFemale NPT Branch Tee Page 23
DTKMale NPT Run Tee Page 24
DTNMale NPT Branch Tee Page 24
DSAFemale NPTConnector Page 18-19
DSSBulkhead FemaleNPT Connector Page 21
DHCTube Stub toFemale NPT Adapter Page 12
DUAUnion Page 26
DSUBulkhead Union Page 21
DURReducing Union Page 27
DLAUnion Elbow Page 12
DTAUnion Tee Page 22
DTRReducing Union Tee Page 25
DXAUnion Cross Page 28
Fluid Connectors
BI-LOK UNION
DX
A
C
DWRENCH FLAT
C
C1C1
C
C
C1
C1
AE
UNION CROSS
PART No. C1D WrenchFlat
HexTube Nut
0.620.750.780.880.910.981.061.111.31
3/8”1/2”1/2”5/8”5/8”13/16”15/16”11/16”15/16”
1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”1”
7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”11/2”
DXA-2-*DXA-3-*DXA-4-*DXA-5-*DXA-6-*DXA-8-*DXA-10-*DXA-12-*DXA-16-*
ATube OD
0.090.120.190.250.280.410.500.620.88
EMin Orifice
0.881.011.071.171.201.401.471.521.81
C
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
0.600.630.700.730.760.860.860.861.04
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
A GLOBAL CONNECTION
BI-Lok Tube Fittings are manufac-tured in four State-of-the-art facili-ties, in two countries, and are mar-keted worldwide through a networkof authorized stocking distributorsand representatives.
In today’s business environment,success is dependant upon the truecreation of value.
For over 75 years, Generant, aleading designer and manufacturerof pressure and flow control prod-ucts, has built a reputationsynonymous with innovative andadvanced design, appl icat ionengineering expertise, quality man-ufacturing and unparalleled service.
In this tradition, BI-Lok Series DDual Ferrule Tube Fittings repre-sent a high quality, cost effective,design solution to instrument gradefluid connector applications.BI-Lok® is a registered trademark of the Ihara Science Corporation, Tokyo, Japan. 28
610202_covs.qxd7:802183aa covs.qxd 6/21/10 1:12 PM Page 2
BI-LOK to O-SEAL
BI-LOK to SAE/MS STRAIGHT THREAD
BI-LOK to AN 37° FLARE
PLUG AND CAP
BI-LOK to WELD
TUBE STUB
DUCAN 37° Flare Union Page 26
DUEBulkhead AN37° Flare Union Page 27
DANAN 37°Flare Adapter Page 5
DCBMale PipeWeld Connector Page 6
DCWTube SocketWeld Union Page 9
DLBMale PipeWeld Elbow Page 13
DLWTube SocketWeld Elbow Page 15
DPCPort Connector Page 17
DREReducer Page 17-18
DSEBulkhead Adapter Page 20
DCUSAE/MS MaleStraight ThreadConnector Page 9
DLOPositionableSAE/MS MaleStraight Thread Elbow Page 15
DBAPlug Page 5
DCACap Page 6
®
Series D
DCOO-Seal Male StraightThread Connector Page 7
DCMO-Seal MaleNPT Connector Page 7
COMPONENTS
DNANut Page 15
DOSFerrule Set Page 16
DTITube Insert Page 23
DOBBack Ferrule Page 16
DOFFront Ferrule Page 16
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 1
BI-Lok Series D Dual Ferrule Tube Fittings are composed of fourprecision machined component parts: 1) fitting body, 2) front fer-rule, 3) back ferrule, 4) nut. BI-Lok Tube Fittings are shipped fullyassembled and individually bagged. Once the tubing has beenfully inserted into the fitting, a leak tight seal is achieved throughthe simple action of tightening the nut against the fitting body. Thetightening of the nut provides the axial thrust required to engagethe captively held ferrules against the outside diameter of the tub-ing.The staged swaging action of the ferrules, with minimal torquetransfer to the tubing during make-up, provides the key to BI-Lok’shigh integrity sealing capability and exceptional service life.
BI-Lok Series D Dual Ferrule Tube Fittings are manufactured to becompletely component intermixable with the Swagelok® brand oftube fittings. Independent third party testing concluded that pieceby piece intermixing of each manufacturer’s component parts, invarious combinations, yielded no performance degradation of thefitting connection. BI-Lok Dual Ferrule Tube Fittings are fully com-patible for use with the Swagelok® brand Gap Inspection Gauges.
The BI-Lok Dual Series D Ferrule Tube Fitting consists of fourelements – nut, front ferrule, back ferrule and fitting body.However, the actual sealing function is accomplished with the addi-tion of a fifth element, the tubing itself. Therefore, the pressure rat-ing of the fitting assembly is a direct function of the tubing select-ed. Proper tube selection is critical and the ultimate responsibilityof the system designer/user. The tables listed on page 2 providethe allowable pressure ratings of a variety of commonly used tubesizes and materials.
CONSTRUCTION AND OPERATION
QUALITY CONTROL
PRESSURE RATINGS
TUBING SELECTION AND PREPARATION
INTERCHANGEABILITY AND GAGEABILITY
MATERIALS OF CONSTRUCTION
ComponentBrass
FittingBody
Bar Stock
Forged ASTM B124, CDA 377 ASTM A182
ASTM A479ASTM B16, CDA 360Front FerruleBack FerruleNut
316 Stainless Steel
Fitting Material
Stainless Steel Fitting Bodies and Nuts are Heat /Lot code traceable. Stainless steelnuts are silver plated to prevent gauling and reduce make-up torque.
Fluid Connectors
BI-Lok Tube Fittings are designed, manufactured and inspected tothe rigid quality requirements of our ISO certified production facili-ty. All Stainless Steel Fittings are Heat/Lot code traceable. BI-LokTube Fittings have been tested and certified to a variety of GlobalInternational Industry standards and regulatory agencies.
The selection of the proper tubing is essential to both the perfor-mance and safety of a tubing system. Careful consideration shouldbe applied to the following variables; system pressure, media, flow,operating temperature and environmental conditions. Tube fittingsshould always be used with similar tube materials. i.e.; StainlessSteel fittings with Stainless Steel tubing and Brass fittings with cop-per tubing. In order to achieve proper fitting make-up, the tubingmust be softer that the fitting material. For stainless steel tubing,we recommend fully annealed seamless or welded and drawn tub-ing of ASTM A269, A213 and A249. Tubing hardness should notexceed Rockwell B-90. For copper tubing, seamless or softannealed ASTM B-75, or seamless soft annealed Type K or TypeL water tubing ASTM B-88 is recommended. Care should be takenin tube handling to ensure that tubing is reasonably straight and iscut in a manner to create smooth square ends, free of burrs.Handling practices should consider that surface scratches on thetube OD may be a potential source of leaks.
*Swagelok® is a registered trade mark of the Swagelok Company
1
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 2
Temperature Stress Factor
TEMP (°F)
200
400
600
800
1000
1.00
.93
.82
.76
.69
1.00
.96
.85
.79
.76
.95
.87
.80
.50
304Stainless Steel
Stress Factor used to calculate maximum allowable working pressuresat elevated temperatures.NOTE: To find the maximum allowable working pressures for varioustube materials at elevated temperatures, simply multiply the maximumallowable working pressure for the the tube size and wall thicknessfound in these charts by the correct Stress Factor found in the tablebelow:
CARBON STEEL TUBINGTube Wall Thickness, (Inches)
0.028 0.035 0.049 0.065 0.083 0.095 0.109 0.120
STAINLESS STEEL TUBINGTube Wall Thickness (Inches)
0.010 0.012 0.014 0.016 0.020 0.028 0.035 0.049 0.065 0.083 0.095 0.109TubeOD1/16”1/8 “3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”
1”
5600 6800 8100 9400 12000
8500
5400
4000
10900
7000
5100
4000
3300
2600
10200
7500
5800
4800
3700
2900
2400
2000
10200
8000
6500
5100
4000
3300
2800
2400
6700
5200
4200
3600
3100
4900
4200
3600
5800
4800
4200
COPPER TUBINGTube Wall Thickness (Inches)
0.028 0.035 0.049 0.065 0.083 0.095 0.109 0.120TubeOD1/8 “3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”
1”
2700
1800
1300
3600
2300
1600
1300
1000
800
5100
3400
2500
1900
1600
1100
900
700
600
500
3500
2700
2200
1600
1200
1000
800
700
2100
1600
1300
1100
900
1900
1500
1300
1100
1800
1500
1300 1500
TubeOD1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”
1”
8000
5100
3700
10200
6600
4800
3700
3100
2300
1800
9600
7000
5500
4500
3200
2600
2100
1800
1500
9600
7500
6200
4500
3500
2900
2400
2100
5900
4600
3700
3200
2700
5300
4300
3700
3200
5100
4300
3700 4100
STRESS FACTORS
Working Pressure, PSIG
Working Pressure, PSIG
Carbon steel hydraulic tubing per ASTM A-179 or equivalent. Workingpressures are based on allowable stress of 15,700 psi between-70°F and 100° F (Reference: ANSI B31.3)
304 and 316 annealed seamless tubing per ASTM A-269 or equivalent working pressure are based onallowable stress of 20,000 psi between -20° F and 100° F (Reference: ANSI B31.3)
Working Pressure, PSIG
Copper tubing per ASTM B-75 or equivalent. Working pressures arebased on allowable stress of 6,000 psi between -70°F and 100° F(Reference: ANSI B31.3)
Carbon Steel Copper316Stainless Steel
PIPE END PRESSURE RATINGS
NPTPipe Size
1/8”
1/4”
3/8”
1/2”
3/4”
1”
Male
10000
8000
7800
7700
7300
5300
Female
6500
6600
5300
4900
4600
4400
Male
5000
4000
3900
3800
3600
2600
Female
3200
3300
2600
2400
2300
2200
316 Stainless andCarbon Steel
Brass
Fittings with both Tube and NPT threaded pipeend connections have different pressure ratings.When specifying these type fittings, please refer tothis chart for maximum allowable pressure ratings.A thread sealant is recommended when usingNPT connections.
2
®
Series D
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 3
Assembly Instructions
The following procedures refer to the properassembly of the BI-Lok Series D Dual FerruleTube Fittings.
1. BI-Lok Tube Fittings are supplied fullyassembled and individually bagged, allowingfor clean efficient make-up. Should compo-nent assembly be required, please note thatthe order of assembly is the front ferrule intothe cone of fitting body, back ferrule and fit-ting nut as noted in Fig. 1.2. Insert the tubing into the fitting body until
it bottoms out against the tube stop shoulderof the fitting. Please note that tubing shouldbe cut squarely and free of burrs.3. Hand tighten the nut as much as possi-
ble, bringing the fitting to what is called the“finger tight” position.4. Secure the fitting body with a wrench and
tighten the nut with another wrench an addi-tional 3/4 of a turn for tube sizes 1/16” thru3/16” or for sizes 1/4” and above 1-1/4 turns.(refer to Fig. 2a, 2b, and 2c).
Reassembly Instructions
To reassemble a BI-Lok Series D DualFerrule Tube Fitting, simply insert the tubeassembly (nut, front and back ferrule pre-swaged on the tube) into the fitting body andhand tighten the nut. Next, using a wrench,rotate the nut approximately 1/4 of a turn(back to the original make-up position) andthen tighten the nut slightly.
Tube Measuring and Fitting
When measuring and bending tubing it isimportant to be aware of two critical mea-surements. The first being the tube insertiondepth (reference dimension G) into the fittingassembly which must be considered in thedetermining the over all length of tuberequired. The other being the minimumlength of straight tubing required for a propertube bend (reference dimension H). Bothmeasurements are dependant on tube OD;please use Fig. 3 for reference purposes.
ASSEMBLY INSTRUCTIONS
Tube Size HHexTube Nut
IStraightThread
1/2”23/32”3/4”13/16”7/8”15/16”13/16”11/4”11/4”15/16”11/2”
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
10-325/16”-203/8”-207/16”-201/2”-209/16”-203/4”-207/8”-201”-2011/8”-2015/16”-20
123456810121416
ATube OD
0.270.340.370.400.440.470.470.470.470.470.56
C
0.340.500.540.600.640.660.900.960.961.021.23
G
5/16”7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”11/4”11/2”
H
TUBEOD G
CI
HEX
STRAIGHTTHREAD
Fig.1
Fig.2a Fig.2c
Fig.2b
Fitting Body Front Ferrule
Back Ferrule
NutTube
Sizes 1/16” to 3/16”3/4 turn
Sizes 1/4” to 1”1-1/4 turn
Fluid Connectors
Fig.3
0.190.250.280.310.340.370.500.560.560.630.75
Tube Step Shoulder
3
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 4
®
Series D
ORDERING INFORMATION
How To OrderBI-Lok tube fittings are ordered by part number as listed in this catalog. The part numbering system is designed so that you caneasily identify the type, configuration, size and material of the fitting. Using the example below, specify the Fitting Type, SizeDesignator, Material and any additional Options desired.
Description PageEnd
Connection 1End
Connection 2TypeDAN AN 37° Flare Union 5 Tube OD AN FlareDBA Plug 5 Tube ODDCA Cap 6 Tube ODDCB Male Pipe Weld Connector 6 Tube OD Male Weld PipeDCM O-Seal Male NPT Connector 7 Tube OD Male NPTDCO O-Seal Male Straight Thread Connector 7 Tube OD Straight ThreadDCT Male NPT Connector 8 Tube OD Male NPTDCU SAE/MS Male Straight Thread Connector 9 Tube OD Straight ThreadDCW Tube Socket Weld Union 9 Tube ODDCTZ Male NPT Connector 10 Tube OD Male NPTDHA Tube Stub to Male NPT Adapter 11 Tube Stub Male NPTDHC Tube Stub to Female NPT Adapter 12 Tube Stub Female NPTDLA Union Elbow 12 Tube ODDLB Male Pipe Weld Elbow 13 Tube OD Male Weld PipeDLF Female NPT Elbow 13 Tube OD Female NPTDLN Male NPT Elbow 14 Tube OD Male NPTDLO Positionalbe SAE/MS Male Straight Thread Elbow 15 Tube OD Straight ThreadDLW Tube Socket Weld Elbow 15 Tube ODDNA Nut 15 Tube ODDOB Back Ferrule 16 Tube ODDOF Front Ferrule 16 Tube ODDOS Ferrule Set 16 Tube ODDPC Port Connector 17 Tube OD Tube StubDRE Reducer 17-18 Tube OD Tube StubDSA Female NPT Connector 18-19 Tube OD Female NPTDSC Bulkhead Male NPT Connector 19 Tube OD Male NPTDSE Bulkhead Reducer 20 Tube OD Tube StubDSL Bulkhead Union Elbow 20 Tube ODDSS Bulkhead Female NPT Connector 21 Tube OD Female NPTDSU Bulkhead Union 21 Tube ODDTA Union Tee 22 Tube ODDTF Female NPT Run Tee 22 Tube OD Female NPTDTH Female NPT Branch Tee 23 Tube OD Female NPTDTI Tube Insert 23 Tube OD Tube IDDTK Male NPT Run Tee 24 Tube OD Male NPTDTN Male NPT Branch Tee 24 Tube OD Male NPTDTR Reducing Union Tee 25 Tube OD Tube OD Tube OD*DUA Union 26 Tube ODDUC AN 37° Flare Union 26 Tube OD AN FlareDUE Bulkhead AN 37° Flare Union 27 Tube OD AN FlareDUR Reducing Union 27 Tube OD Tube ODDXA Union Cross 28 Tube OD
SS - 316 stainless steel, ASTM A479B - Brass, ASTM B16
Tube OD orThreaded Connection
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
SizeIndicator
123456810121416
Size DesignatorFitting Type
*
N - Nylon FerrulesT - T eflon FerrulesX - Cleaned and packaged for oxygen service
Material Option
*For DTR specify end connection, 1, 2 and 3, see page 25.
4
DCT - -SS4-4-
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 5
HEX
A
L
D
A
HEX
L
DAN AN 37° FLARE ADAPTER
DBA
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are withthe nut in the finger-tight position.
Fluid Connectors
PART No. JANTube Size
LA
Tube ODHex
Tube NutHexBody
0.540.620.620.720.851.12
1/8”1/4”1/4”3/8”1/2”1”
0.770.800.880.981.251.71
1/8”1/8”1/4”3/8”1/2”1”
7/16”7/16”9/16”11/16”7/8”11/2”
3/8”9/16”9/16”11/16”7/8”11/2”
DAN-2-2-*DAN-2-4-*DAN-4-4-*DAN-6-6*DAN-8-8-*DAN-16-16-** Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
PLUG
PART No. LA
Tube ODHex
Tube Nut
0.310.470.470.500.530.560.690.690.690.690.81
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
5/16”7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”11/4”11/2”
DBA-1-*DBA-2-*DBA-3-*DBA-4-*DBA-5-*DBA-6-*DBA-8-*DBA-10-*DBA-12-*DBA-14-*DBA-16-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
J
5
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 6
®
Series D
F
A
L
HEX
H
D
37.5
A BE
L
HEX
D
F
W
DCACAP
PART No.LOALD F
ATube OD
HexTube Nut
HexBody
0.590.790.840.920.961.011.141.171.231.341.51
0.440.600.630.700.730.760.860.860.860.861.04
0.440.530.580.630.670.720.750.780.840.941.03
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
5/16”7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”11/4”11/2”
5/16”7/16”7/16”1/2”9/16”5/8”13/16”15/16”11/16”13/16”13/8”
DCBMALE PIPEWELD CONNECTOR
PARTNo.LOAL
D FATube OD
HexTube Nut
EMin Orifice
WB
1.181.231.301.491.571.571.811.721.711.922.001.931.992.282.272.45
0.440.630.700.700.760.760.760.860.860.860.860.860.860.861.041.04
0.920.971.001.201.281.281.511.311.311.511.591.531.591.871.771.97
1/8”3/16”1/4”1/4”3/8”3/8”3/8”1/2”1/2”1/2”1/2”5/8”3/4”3/4”1”1”
0.090.120.190.190.280.280.280.410.410.410.410.500.620.620.880.88
7/16”1/2”9/16”9/16”11/16”11/16”11/16”7/8”7/8”7/8”7/8”1”11/8”11/8”11/2”11/2”
PipeSize1/8”1/8”1/8”1/4”1/4”3/8”1/2”1/4”3/8”1/2”3/4”1/2”3/4”1”1/2”1”
HexBody
7/16”7/16”1/2”9/16”5/8”11/16”7/8”13/16”13/16”7/8”11/16”15/16”11/16”13/8”13/8”13/8”
0.380.380.380.560.560.560.750.560.560.750.750.750.750.940.750.94
0.4050.4050.4050.5400.5400.6750.8400.5400.6750.8401.0500.8401.0501.3150.8401.315
DCB-2-2-*DCB-3-2-*DCB-4-2-*DCB-4-4-*DCB-6-4-*DCB-6-6-*DCB-6-8-*DCB-8-4-*DCB-8-6-*DCB-8-8-*DCB-8-12-*DCB-10-8-*DCB-12-12-*DCB-12-16-*DCB-16-8-*DCB-16-16-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
DCA-1-*DCA-2-*DCA-3-*DCA-4-*DCA-5-*DCA-6-*DCA-8-*DCA-10-*DCA-12-*DCA-14-*DCA-16-*
6
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 7
3/4”3/4”15/16”3/4”15/16”15/16”
DCM
A KE
L
THEX
D
F
L1
O-SEAL MALE NPT CONNECTOR
DCO
F
A KE
L
THEX
D L1
O-SEAL MALE STRAIGHT THREAD CONNECTOR
PARTNo. LOAL
D FATube OD
EMin Orifice
HexTube Nut
L1TNPT
1.291.381.511.471.581.95
0.600.700.700.760.760.86
1.031.091.221.181.281.56
1/8”1/4”1/4”3/8”3/8”1/2”
0.090.190.190.280.280.41
7/16”9/16”9/16”11/16”11/16”7/8”
0.280.280.380.280.380.53
K
0.740.740.930.740.931.30
O-RingSize
- 111- 111- 113- 111- 113- 212
1/8”1/8”1/4”1/8”1/4”1/2”
DCM-2-2-*DCM-4-2-*DCM-4-4-*DCM-6-2-*DCM-6-4-*DCM-8-8-*
PARTNo.LOAL
D FATube OD
EMin Orifice
HexTube Nut
L1TStraight Thread
1.051.291.361.511.601.671.812.06
0.440.600.630.700.730.760.860.86
0.901.021.101.231.321.381.411.65
1/16”1/8”3/16”1/4”5/16”3/8”1/2”3/4”
0.050.090.120.190.250.280.410.62
5/16”7/16”1/2”9/16”5/8”11/16”7/8”11/8”
HexBody
9/16”9/16”5/8”3/4”7/8”15/16”11/8”11/2”
0.340.340.380.410.440.470.470.56
K
0.550.550.620.740.860.931.111.49
O-RingSize
- 011- 011- 012- 111- 112- 113- 116- 215
5/16”-245/16”-243/8”-247/16”-201/2”-209/16”-183/4”-1611/16”-12
DCO-1-2-*DCO-2-2-*DCO-3-3-*DCO-4-4-*DCO-5-5-*DCO-6-6-*DCO-8-8-*DCO-12-12-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
Fluid Connectors
HexBody
Note: To achieve proper leak-tight seal, a smooth flat surface perpendicular to the threads is necessary.
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.7
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 8
®
Series D
A E
F
LD
HEX
T
MALE NPT CONNECTOR
LOAL
D FATube OD
HexTube Nut
TNPT
HexBody
0.941.001.171.171.391.211.431.301.301.491.521.761.771.351.531.391.571.571.801.831.721.721.911.942.281.741.941.942.002.002.281.992.272.272.46
0.440.440.600.600.600.630.630.700.700.700.700.700.700.730.730.760.760.760.760.760.860.860.860.860.860.860.860.860.860.860.860.861.041.041.04
0.790.850.910.911.120.941.161.001.001.191.221.441.471.051.231.091.281.281.501.541.311.311.501.541.871.341.541.531.591.591.871.591.771.771.97
1/16”1/16”1/8”1/8”1/8”3/16”3/16”1/4”1/4”1/4”1/4”1/4”1/4”5/16”5/16”3/8”3/8”3/8”3/8”3/8”1/2”1/2”1/2”1/2”1/2”5/8”5/8”5/8”3/4”3/4”3/4”7/8”1”1”1”
EMin Orifice
0.050.050.090.090.090.120.120.190.190.190.190.190.190.250.250.280.280.280.280.280.280.410.410.410.410.410.500.500.500.620.620.720.500.720.88
5/16”5/16”7/16”7/16”7/16”1/2”1/2”9/16”9/16”9/16”9/16”9/16”9/16”5/8”5/8”11/16”11/16”11/16”11/16”11/16”7/8”7/8”7/8”7/8”7/8”1”1”1”11/8”11/8”11/8”11/4”11/2”11/2”11/2”
1/16”1/8”1/16”1/8”1/4”1/8”1/4”1/16”1/8”1/4”3/8”1/2”3/4”1/8”1/4”1/8”1/4”3/8”1/2”3/4”1/4”3/8”1/2”3/4”1”3/8”1/2”3/4”1/2”3/4”1”3/4”1/2”3/4”1”
5/16”7/16”7/16”7/16”9/16”7/16”9/16”1/2”1/2”9/16”11/16”7/8”11/16”9/16”9/16”5/8”5/8”11/16”7/8”11/16”13/16”13/16”7/8”11/16”13/8”15/16”15/16”11/16”11/16”11/16”13/8”113/16”13/8”13/8”13/8”
DCT
PARTNo.
DCT-1-1-*DCT-1-2-*DCT-2-1-*DCT-2-2-*DCT-2-4-*DCT-3-2-*DCT-3-4-*DCT-4-1-*DCT-4-2-*DCT-4-4-*DCT-4-6-*DCT-4-8-*DCT-4-12-*DCT-5-2-*DCT-5-4-*DCT-6-2-*DCT-6-4-*DCT-6-6-*DCT-6-8-*DCT-6-12-*DCT-8-4-*DCT-8-6-*DCT-8-8-*DCT-8-12-*DCT-8-16-*DCT-10-6-*DCT-10-8-*DCT-10-12-*DCT-12-8-*DCT-12-12-*DCT-12-16-*DCT-14-12-*DCT-16-8-*DCT-16-12-*DCT-16-16-** Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
8
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 9
DCU
F
A E
L1
L
D
HEX T
SAE/MS MALE STRAIGHT THREAD CONNECTOR
DCW
A A1 BE
LD
L1
HEX
F
TUBE SOCKETWELD UNION
PARTNo. D L1A
Tube ODHexTube Nut
TStraight Thread
EMin Orifice
LOAL
HexBodyF
0.600.700.700.700.760.760.760.760.860.860.860.860.860.860.860.861.041.04
5/16”-247/16”-209/16”-183/4”-167/16”-209/16”-183/4”-167/8”-149/16”-183/4”-167/8”-1411/16”-123/4”-167/8”-143/4”-1611/16”-1211/16”-1215/16”-12
0.300.360.390.440.360.390.440.500.390.440.500.590.440.500.440.590.590.59
1/8”1/4”1/4”1/4”3/8”3/8”3/8”3/8”1/2”1/2”1/2”1/2”5/8”5/8”3/4”3/4”1”1”
0.090.190.190.190.280.280.280.280.410.410.410.410.500.500.620.620.890.89
7/16”9/16”9/16”9/16”11/16”11/16”11/16”11/16”7/8”7/8”7/8”7/8”1”1”11/8”11/8”11/2”11/2”
1.191.351.411.481.411.461.551.671.551.661.791.941.661.791.701.942.132.16
7/16”9/16”11/16”7/8”5/8”11/16”7/8”1”
13/16”7/8”1”11/4”15/16”1”
11/16”11/4”13/8”11/2”
O-RingSize
-902-904-906-908-904-906-908-910-906-908-910-912-908-910-908-912-912-916
0.921.051.111.181.111.171.251.381.141.251.381.531.251.381.291.531.631.66
DCU-2-2-*DCU-4-4-*DCU-4-6-*DCU-4-8-*DCU-6-4-*DCU-6-6-*DCU-6-8-*DCU-6-10-*DCU-8-6-*DCU-8-8-*DCU-8-10-*DCU-8-12-*DCU-10-8-*DCU-10-10-*DCU-12-8-*DCU-12-12-*DCU-16-12-*DCU-16-16-*
DCW A1Tube ODD F
ATube OD
EMin Orifice
HexTube Nut L1 B
1/8”1/4”3/8”1/2”3/4”1”
0.600.700.760.860.861.04
0.881.031.191.221.311.59
1/8”1/4”3/8”1/2”3/4”1”
0.090.190.280.410.620.89
5/16”9/16”11/16”7/8”11/8”11/2”
0.250.310.380.500.560.75
LOAL
1.141.321.481.621.712.07
HexBody
7/16”1/2”5/8”13/16”11/6”13/8”
0.310.440.620.751.051.31
DCW-2-*DCW-4-*DCW-6-*DCW-8-*DCW-12-*DCW-16-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
Fluid Connectors
9
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 10
DCTZ
A
LT
HEX
D
F
THERMOCOUPLE CONNECTOR
PART No.LOALD F
ATube OD
HexTube Nut
HexBody
0.941.001.221.171.171.401.411.651.221.431.291.491.511.751.521.761.571.571.811.711.921.941.931.941.992.272.45
0.440.440.440.600.600.600.600.600.630.630.700.700.700.700.730.730.760.760.760.860.860.860.860.860.860.861.04
0.780.851.070.910.921.131.151.390.961.171.001.201.221.441.231.471.281.281.501.311.501.541.531.541.591.851.97
1/16”1/16”1/16”1/8”1/8”1/8”1/8”1/8”3/16”3/16”1/4”1/4”1/4”1/4”5/16”5/16”3/8”3/8”3/8”1/2”1/2”1/2”5/8”5/8”3/4”7/8”1”
5/16”5/16”5/16”7/16”7/16”7/16”7/16”7/16”1/2”1/2”9/16”9/16”9/16”9/16”5/8”5/8”11/16”11/16”11/16”7/8”7/8”7/8”1”1”11/8”11/4”11/2”
TNPT
1/16”1/8”1/4”1/16”1/8”1/4”3/8”1/2”1/8”1/4”1/8”1/4”3/8”1/2”1/4”1/2”1/4”3/8”1/2”3/8”1/2”3/4”1/2”3/4”3/4”1”1”
5/16”7/16”9/16”7/16”7/16”9/16”11/16”7/8”7/16”9/16”1/2”9/16”11/16”7/8”9/16”7/8”5/8”11/16”7/8”13/16”7/8”11/16”15/16”11/16”11/16”13/8”13/8”
DCTZ-1-1-*DCTZ-1-2-*DCTZ-1-4-*DCTZ-2-1-*DCTZ-2-2-*DCTZ-2-4-*DCTZ-2-6-*DCTZ-2-8-*DCTZ-3-2-*DCTZ-3-4-*DCTZ-4-2-*DCTZ-4-4-*DCTZ-4-6-*DCTZ-4-8-*DCTZ-5-4-*DCTZ-5-8-*DCTZ-6-4-*DCTZ-6-6-*DCTZ-6-8-*DCTZ-8-6-*DCTZ-8-8-*DCTZ-8-12-*DCTZ-10-8-*DCTZ-10-12-*DCTZ-12-12-*DCTZ-14-16-*DCTZ-16-16-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
Tube OD
Up to 1/2”
Above 1/2” to 3/4”
Above 3/4”
Factor
.75
.50
.25
For use with thermocouples or other types ofprobes. Bored through fittings carry a reducedpressure rating. Please apply the following factorto the allowable working pressure of the tubing asstated on page 2.
10
®
Series D
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 11
Fluid Connectors
DHA
F
A
L1HEX
T
E
TUBE STUB TO MALE NPT ADAPTER
PART No.TNPT
LOAL
ATube OD
L1HexBody
1/8”1/4”1/8”1/4”1/8”1/4”3/8”1/2”1/8”1/4”1/8”1/4”3/8”1/2”1/4”3/8”1/2”1/2”1/2”3/4”1”3/4”
1.121.321.151.341.221.401.441.651.251.461.311.501.501.711.711.751.932.002.002.032.282.28
1/8”1/8”3/16”3/16”1/4”1/4”1/4”1/4”5/16”5/16”3/8”3/8”3/8”3/8”1/2”1/2”1/2”5/8”3/4”3/4”3/4”1”
0.550.550.580.580.650.650.650.650.680.680.710.710.710.710.930.930.930.990.990.990.991.28
EMin Orifice
0.080.080.120.120.190.190.190.190.250.250.280.280.280.280.390.390.390.500.590.590.590.60
7/16”9/16”7/16”9/16”7/16”9/16”11/16”7/8”7/16”9/16”7/16”9/16”11/16”7/8”9/16”11/16”7/8”7/8”7/8”11/16”13/8”11/16”
DHA-2-2-*DHA-2-4-*DHA-3-2-*DHA-3-4-*DHA-4-2-*DHA-4-4-*DHA-4-6-*DHA-4-8-*DHA-5-2-*DHA-5-4-*DHA-6-2-*DHA-6-4-*DHA-6-6-*DHA-6-8-*DHA-8-4-*DHA-8-6-*DHA-8-8-*DHA-10-8-*DHA-12-8-*DHA-12-12-*DHA-12-16-*DHA-16-12-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
L
11
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 12
DHC
F
A E
HEX
L1 T
TUBE STUB TO FEMALE NPT ADAPTER
DLA
D CC1
C
A
C1 WRENCH FLAT
B
E
UNION ELBOW
PART No. C1D WrenchFlat
HexTube Nut
0.550.620.740.770.840.910.991.071.121.291.30
3/8”3/8”1/2”1/2”5/8”5/8”13/16”15/16”11/16”11/4”15/16”
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
5/16”7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”11/4”11/2”
DLA-1-*DLA-2-*DLA-3-*DLA-4-*DLA-5-*DLA-6-*DLA-8-*DLA-10-*DLA-12-*DLA-14-*DLA-16-*
PART No. L1 LOAL
ATube OD
TNPT
EMin Orifice
HexBody
1.221.341.261.371.321.441.781.351.461.391.501.611.831.711.852.071.902.132.18
0.550.550.580.580.650.650.650.680.680.710.710.710.710.930.930.930.990.990.99
0.080.080.130.130.190.190.190.250.250.280.280.280.280.390.390.390.500.590.59
1/8”1/8”3/16”3/16”1/4”1/4”1/4”5/16”5/16”3/8”3/8”3/8”3/8”1/2”1/2”1/2”5/8”3/4”3/4”
1/8”1/4”1/8”1/4”1/8”1/4”1/2”1/8”1/4”1/8”1/4”3/8”1/2”1/4”3/8”1/2”3/8”1/2”3/4”
DHC-2-2-*DHC-2-4-*DHC-3-2-*DHC-3-4-*DHC-4-2-*DHC-4-4-*DHC-4-8-*DHC-5-2-*DHC-5-4-*DHC-6-2-*DHC-6-4-*DHC-6-6-*DHC-6-8-*DHC-8-4-*DHC-8-6-*DHC-8-8-*DHC-10-6-*DHC-12-8-*DHC-12-12-*
ATube OD
0.050.090.120.190.250.280.410.500.620.720.88
EMin Orifice
0.710.881.001.061.131.201.401.481.531.691.81
C
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
9/16”3/4”9/16”3/4”9/16”3/4”11/16”9/16”3/4”9/16”3/4”7/8”11/16”3/4”7/8”11/16”7/8”11/16”11/4”
0.440.600.630.700.730.760.860.860.860.861.04
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
L
12
®
Series D
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 13
DLB
B
D C2
W
C
A E
WRENCH FLATC1
MALE PIPEWELD ELBOW
DLF
WRENCH FLAT
C
D C2
CC1
T
A E
FEMALE NPT ELBOW
PARTNo. PipeSizeD CA
Tube ODE
Min OrificeHex
Tube Nut B W
1/8”1/4”1/4”3/8”1/2”1”
0.700.700.760.760.861.04
1.061.061.061.241.431.81
1/4”1/4”3/8”3/8”1/2”1”
0.190.190.190.280.410.89
9/16”9/16”11/16”11/16”7/8”11/2”
0.4050.5400.5400.6750.8401.315
C1
0.780.780.780.941.031.31
C2
0.740.931.001.121.301.84
1/2”1/2”5/8”11/16”15/16”15/16”
0.380.560.560.560.751.05
DLB-4-2-*DLB-4-4-*DLB-6-4-*DLB-6-6-*DLB-8-8-*DLB-16-16*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
WrenchFlat
PARTNo. D CATube OD
EMin Orifice
TNPT
HexTube Nut
1/8”1/4”1/8”1/4”3/8”1/2”1/8”1/4”1/8”1/4”3/8”1/2”1/4”3/8”1/2”3/4”3/8”1/2”1/2”3/4”3/4”3/4”1”
0.600.600.700.700.700.700.730.730.760.760.760.760.860.860.860.860.860.860.860.860.861.041.04
0.961.081.051.171.261.401.181.201.201.231.321.421.401.431.531.671.471.531.521.661.681.812.07
1/8”1/8”1/4”1/4”1/4”1/4”5/16”5/16”3/8”3/8”3/8”3/8”1/2”1/2”1/2”1/2”5/8”5/8”3/4”3/4”7/8”1”1”
0.090.090.190.190.190.190.250.250.280.280.280.280.410.410.410.410.500.500.620.620.720.880.88
7/16”7/16”9/16”9/16”9/16”9/16”5/8”5/8”11/16”11/16”11/16”11/16”7/8”7/8”7/8”7/8”1”1”11/8”11/8”11/4”11/2”11/2”
C1
0.690.810.750.890.971.110.890.910.910.941.031.110.981.031.111.251.061.111.111.251.281.311.67
C2
0.750.890.750.890.891.120.750.890.750.890.891.120.890.891.121.250.891.121.121.251.251.251.50
5/8”13/16”5/8”13/16”15/16”11/16”5/8”13/16”5/8”13/16”15/16”11/16”13/16”15/16”11/16”15/16”15/16”11/16”11/16”15/16”15/16”15/16”13/4”
DLF-2-2-*DLF-2-4-*DLF-4-2-*DLF-4-4-*DLF-4-6-*DLF-4-8-*DLF-5-2-*DLF-5-4-*DLF-6-2-*DLF-6-4-*DLF-6-6-*DLF-6-8-*DLF-8-4-*DLF-8-6-*DLF-8-8-*DLF-8-12-*DLF-10-6-*DLF-10-8-*DLF-12-8-*DLF-12-12-*DLF-14-12-*DLF-16-12-*DLF-16-16-*
WrenchFlat
Fluid Connectors
13
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 14
DLN
WRENCH FLAT
W
CC1
C2
A
E
D
T
MALE NPT ELBOW
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
PARTNo. D CATube OD
EMin Orifice
TNPT
HexTube Nut
1/16”1/8”1/16”1/8”1/4”1/8”1/4”1/16”1/8”1/4”3/8”1/2”1/8”1/4”3/8”1/8”1/4”3/8”1/2”3/4”1/4”3/8”1/2”3/4”3/8”1/2”3/4”1/2”3/4”3/4”3/4”1”
0.440.440.600.600.600.630.630.700.700.700.700.700.730.730.730.760.760.760.760.760.860.860.860.860.860.860.860.860.860.861.041.04
0.720.720.930.930.971.001.001.001.061.061.171.251.181.181.241.201.201.231.311.411.391.391.441.521.471.471.521.521.521.681.811.81
1/16”1/16”1/8”1/8”1/8”3/16”3/16”1/4”1/4”1/4”1/4”1/4”5/16”5/16”5/16”3/8”3/8”3/8”3/8”3/8”1/2”1/2”1/2”1/2”5/8”5/8”5/8”3/4”3/4”7/8”1”1”
0.050.050.090.090.090.120.120.190.190.190.190.190.250.250.250.280.280.280.280.280.410.410.410.410.500.500.500.620.620.720.880.88
5/16”5/16”7/16”7/16”7/16”1/2”1/2”9/16”9/16”9/16”9/16”9/16”5/8”5/8”5/8”11/16”11/16”11/16”11/16”11/16”7/8”7/8”7/8”7/8”1”1”1”11/8”11/8”11/4”11/2”11/2”
C1
0.560.560.670.670.710.740.740.780.780.780.880.960.880.880.940.910.910.941.021.110.980.981.031.111.061.061.111.111.111.281.311.31
C2
0.730.730.730.730.930.740.830.740.740.921.121.300.811.001.120.821.001.121.261.401.081.081.321.401.161.341.401.391.391.651.651.84
7/16”7/16”7/16”7/16”1/2”1/2”1/2”1/2”1/2”1/2”11/16”13/16”5/8”5/8”11/16”5/8”5/8”11/16”13/16”11/16”13/16”13/16”13/16”11/16”15/16”15/16”11/16”11/16”11/16”11/4”15/16”15/16”
DLN-1-1-*DLN-1-2-*DLN-2-1-*DLN-2-2-*DLN-2-4-*DLN-3-2-*DLN-3-4-*DLN-4-1-*DLN-4-2-*DLN-4-4-*DLN-4-6-*DLN-4-8-*DLN-5-2-*DLN-5-4-*DLN-5-6-*DLN-6-2-*DLN-6-4-*DLN-6-6-*DLN-6-8-*DLN-6-12-*DLN-8-4-*DLN-8-6-*DLN-8-8-*DLN-8-12-*DLN-10-6-*DLN-10-8-*DLN-10-12-*DLN-12-8-*DLN-12-12-*DLN-14-12-*DLN-16-12-*DLN-16-16-*
WrenchFlat
14
®
Series D
610202_text.qxd7:802183aa text.qxd 6/21/10 2:16 PM Page 15
DLW
B
D C2
W
C
A
A1
E
WRENCH FLAT
W
C1
TUBE SOCKETWELD ELBOW
Fluid Connectors
PARTNo. A1Tube OD
D CATube OD
EMin Orifice
HexTube Nut BW
1/8”1/4”3/8”1/2”1”
0.600.700.760.861.04
0.891.061.201.401.81
1/8”1/4”3/8”1/2”1”
0.090.190.280.410.88
5/16”9/16”11/16”7/8”11/2”
0.440.570.700.841.40
C1
0.620.770.910.981.31
C2
0.891.071.201.391.81
3/8”1/2”5/8”13/16”15/16”
0.250.310.380.500.75
DLW-2-*DLW-4-*DLW-6-*DLW-8-*DLW-16-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
WrenchFlat
DLO
D
HEX 1
T
C2
C
A E
WRENCH FLATC1
POSITIONABLE SAE/MS MALE STRAIGHT THREAD ELBOW
PARTNo. TStraight Thread
DATube OD
EMin Orifice
HexTube Nut
7/16”-209/16”-181/2”-209/16”-183/4”-163/4”-16
0.700.700.730.760.760.86
1/4”1/4”5/16”3/8”3/8”1/2”
0.190.190.230.280.280.41
HexLock Nut
9/16”11/16”5/8”11/16”7/8”7/8”
9/16”9/16”5/8”11/16”11/16”7/8”
C1
0.830.910.900.971.081.08
C2
1.121.271.161.271.491.49
5/8”5/8”5/8”5/8”13/16”13/16”
DLO-4-4-*DLO-4-6-*DLO-5-5-*DLO-6-6-*DLO-6-8-*DLO-8-8-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
WrenchFlat
-904-906-905-906-908-908
O-RingSize
DNA
A
HEX
L
NUT
PARTNo. LOAL
ATube OD
HexTube Nut
0.310.470.470.500.530.560.690.690.690.690.81
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
5/16”7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”11/4”11/2”
DNA-1-*DNA-2-*DNA-3-*DNA-4-*DNA-5-*DNA-6-*DNA-8-*DNA-10-*DNA-12-*DNA-14-*DNA-16-*
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
C
1.121.201.191.261.371.48
15
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 16
DOFFRONT FERRULE
A
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
PARTNo. ATube OD
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
DOF-1-*DOF-2-*DOF-3-*DOF-4-*DOF-5-*DOF-6-*DOF-8-*DOF-10-*DOF-12-*DOF-14-*DOF-16-*
PARTNo. ATube OD
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
DOS-1-*DOS-2-*DOS-3-*DOS-4-*DOS-5-*DOS-6-*DOS-8-*DOS-10-*DOS-12-*DOS-14-*DOS-16-*
DOS
A
FERRULE SET
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
DOB
A
PARTNo. ATube OD
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
DOB-1-*DOB-2-*DOB-3-*DOB-4-*DOB-5-*DOB-6-*DOB-8-*DOB-10-*DOB-12-*DOB-14-*DOB-16-*
BACK FERRULE
16
®
Series D
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 17
PORT CONNECTOR
PART No.L
OALA1
Tube ODF
ATube OD
EMin Orifice
0.830.970.881.131.091.241.581.671.802.28
1/16”1/8”
1/16”1/8”1/4”1/4”3/8”1/2”3/4”1”
0.390.620.420.620.740.740.801.021.091.42
1/8”1/8”1/4”1/4”1/4”3/8”1/2”1/2”3/4”1”
0.030.090.030.090.190.190.280.390.590.80
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
DPC-2-1-*DPC-2-*DPC-4-1-*DPC-4-2-*DPC-4-*DPC-6-4-*DPC-8-6-*DPC-8-*DPC-12-*DPC-16-*
Note: SPECIAL INSTALLATIONINSTRUCTIONS FOR MACHINEDFERRULE END OF DPC.From the finger-tight position,tighten nut 1/4 turn only.Subsequent connections aremade by tightening slightly witha wrench after snugging nut byhand.
L
A1 AE
FDP
C
REDUCER
DR
EFluid Connectors
PARTNo. A1Tube ODD FA
Tube ODE
Min OrificeHex
Tube Nut
1/8”1/8”
3/16”1/4”3/8”1/2”1/4”1/2”1/8”
3/16”1/4”
5/16”3/8”1/2”5/8”3/4”3/8”1/2”
0.440.600.600.600.600.600.630.630.700.700.700.700.700.700.700.700.730.73
1.001.061.091.161.221.481.201.501.161.191.251.281.311.541.531.691.361.58
1/16”1/8”1/8”1/8”1/8”1/8”3/16”3/16”1/4”1/4”1/4”1/4”1/4”1/4”1/4”1/4”5/16”5/16”
0.050.080.090.090.090.090.080.120.080.120.190.190.190.190.190.190.250.25
5/16”7/16”7/16”7/16”7/16”7/16”1/2”1/2”9/16”9/16”9/16”9/16”9/16”9/16”9/16”9/16”5/8”5/8”
LOAL
1.151.321.361.421.481.741.461.841.451.481.541.571.601.821.891.891.651.87
HexBody
5/16”7/16”7/16”7/16”7/16”9/16”7/16”9/16”1/2”1/2”1/2”1/2”1/2”
9/16”11/16”7/8”
9/16”9/16”
DRE-1-2-*DRE-2-2-*DRE-2-3-*DRE-2-4-*DRE-2-6-*DRE-2-8-*DRE-3-4-*DRE-3-8-*DRE-4-2-*DRE-4-3-*DRE-4-4-*DRE-4-5-*DRE-4-6-*DRE-4-8-*DRE-4-10-*DRE-4-12-*DRE-5-6-*DRE-5-8-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass. (CONTINUED ON NEXT PAGE)
A A1E
LD
HEX
F
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.17
610202_text.qxd7:802183aa text.qxd 6/23/10 11:03 AM Page 18
DREREDUCER CONTINUED
DSAFEMALE NPT CONNECTOR
PARTNo. A1Tube OD
D FATube OD
EMin Orifice
HexTube Nut
1/8”1/4”5/16”3/8”1/2”5/8”3/4”1/4”3/8”1/2”5/8”3/4”1”3/4”7/8”1”3/8”1/2”7/8”1”3/8”3/4”1/2”7/8”
0.760.760.760.760.760.760.760.860.860.860.860.860.860.860.860.860.860.860.860.860.860.861.041.04
1.241.271.341.411.621.691.691.391.451.661.721.721.971.751.812.021.551.791.852.071.631.902.032.09
3/8”3/8”3/8”3/8”3/8”3/8”3/8”1/2”1/2”1/2”1/2”1/2”1/2”5/8”5/8”5/8”3/4”3/4”3/4”3/4”7/8”7/8”1”1”
0.080.190.190.280.280.280.280.190.280.390.410.410.410.500.500.500.620.390.620.620.720.720.880.88
11/16”11/16”11/16”11/16”11/16”11/16”11/16”7/8”7/8”7/8”7/8”7/8”7/8”1”1”1”11/8”11/8”11/8”11/8”11/4”11/4”11/2”11/2”
LOAL
1.541.571.631.701.911.981.981.791.852.072.122.122.372.152.212.421.962.192.262.462.042.302.522.59
HexBody
5/8”5/8”5/8”5/8”5/8”11/16”13/16”13/16”13/16”13/16”13/16”13/16”11/16”15/16”15/16”11/16”11/16”11/16”11/16”11/16”13/16”13/16”13/8”13/8”
DRE-6-2-*DRE-6-4-*DRE-6-5-*DRE-6-6-*DRE-6-8-*DRE-6-10-*DRE-6-12-*DRE-8-4-*DRE-8-6-*DRE-8-8-*DRE-8-10-*DRE-8-12-*DRE-8-16-*DRE-10-12-*DRE-10-14-*DRE-10-16-*DRE-12-6-*DRE-12-8-*DRE-12-14-*DRE-12-16-*DRE-14-6-*DRE-14-12-*DRE-16-8-*DRE-16-14-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
A E
L
T
HEX
D
F
PARTNo. TNPTD FA
Tube ODE
Min OrificeHex
Tube Nut
1/8”1/4”1/2”1/8”1/16”1/8”1/4”3/8”1/2”
0.600.600.600.630.700.700.700.700.70
0.801.061.340.910.940.941.121.191.40
1/8”1/8”1/8”3/16”1/4”1/4”1/4”1/4”1/4”
0.090.090.090.120.190.190.190.190.19
7/16”7/16”7/16”1/2”9/16”9/16”9/16”9/16”9/16”
LOAL
1.141.321.801.171.231.231.411.481.70
HexBody
9/16”3/4”11/16”9/16”1/2”9/16”3/4”7/8”11/16”
DSA-2-2-*DSA-2-4-*DSA-2-8-*DSA-3-2-*DSA-4-1-*DSA-4-2-*DSA-4-4-*DSA-4-6-*DSA-4-8-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass. (CONTINUED ON NEXT PAGE)
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
A A1E
LD
HEX
F
18
®
Series D
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 19
DSA
A E
L
T
HEX
D
F
FEMALE NPT CONNECTOR CONTINUED
DSC
A E
LT
HEX
D
L1
F
BULKHEAD MALE NPT CONNECTOR
PARTNo. TNPT
D FATube OD
EMin Orifice
HexTube Nut
1/8”1/4”1/8”1/4”3/8”1/2”3/4”1”1/8”1/4”3/8”1/2”3/4”1”3/8”1/2”3/4”3/8”1/2”3/4”3/4”3/4”1”
0.730.730.760.760.760.760.760.760.860.860.860.860.860.860.860.860.860.860.860.860.861.041.04
0.971.161.001.191.251.441.551.871.001.251.251.441.501.871.251.441.501.341.441.501.561.621.97
5/16”5/16”3/8”3/8”3/8”3/8”3/8”3/8”1/2”1/2”1/2”1/2”1/2”1/2”5/8”5/8”5/8”3/4”3/4”3/4”7/8”1”1”
0.250.250.280.280.280.280.280.280.410.410.410.410.410.410.500.500.500.620.620.620.720.880.88
5/8”5/8”11/16”11/16”11/16”11/16”11/16”11/16”7/8”7/8”7/8”7/8”7/8”7/8”1”1”1”11/8”11/8”11/8”11/4”11/2”11/2”
LOAL
1.261.451.291.481.541.731.842.171.411.641.641.831.892.251.641.831.901.741.831.891.952.102.45
HexBody
9/16”3/4”5/8”3/4”7/8”11/16”15/16”15/8”11/16”13/16”7/8”11/16”15/16”15/8”15/16”11/16”15/16”11/16”11/16”15/16”15/16”13/8”15/8”
DSA-5-2-*DSA-5-4-*DSA-6-2-*DSA-6-4-*DSA-6-6-*DSA-6-8-*DSA-6-12-*DSA-6-16-*DSA-8-2-*DSA-8-4-*DSA-8-6-*DSA-8-8-*DSA-8-12-*DSA-8-16-*DSA-10-6-*DSA-10-8-*DSA-10-12-*DSA-12-6-*DSA-12-8-*DSA-12-12-*DSA-14-12-*DSA-16-12-*DSA-16-16-*
Fluid Connectors
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
PARTNo. TNPTD F
ATube OD
EMin Orifice
HexTube Nut
1/8”1/8”1/4”1/4”3/8”1/2”3/8”1/2”3/4”1”
1.241.321.321.451.451.451.631.631.852.28
1.571.661.841.971.972.302.092.902.603.19
1/8”1/4”1/4”3/8”3/8”3/8”1/2”1/2”3/4”1”
0.090.190.190.280.280.280.410.410.620.88
5/16”9/16”9/16”11/16”11/16”11/16”7/8”7/8”11/8”11/2”
LOAL
1.831.952.112.262.262.602.492.663.003.67
L1Panel HoleDrill Size
Max PanelThickness
0.971.031.031.161.161.161.251.251.471.78
21/64”29/64”29/64”37/64”37/64”37/64”49/64”49/64”11/64”121/64”
0.500.400.400.440.440.440.500.500.660.75
HexBody
1/2”5/8”5/8”3/4”3/4”7/8”15/16”15/16”13/16”15/8”
DSC-2-2-*DSC-4-2-*DSC-4-4-*DSC-6-4-*DSC-6-6-*DSC-6-8-*DSC-8-6-*DSC-8-8-*DSC-12-12-*DSC-16-16-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.19
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 20
G
DSE
F
A E
L
HEX
D F1
L1
BULKHEAD ADAPTER
PARTNo. EMin OrificeD F1A
Tube OD FHex
Tube Nut
0.090.190.280.39
1.231.321.451.64
0.550.650.710.93
1/8”1/4”3/8”1/2”
1.691.912.122.47
5/16”9/16”11/16”7/8”
LOAL
1.952.202.412.87
L1 Panel HoleDrill Size
Max PanelThickness
0.971.031.161.26
21/64”29/64”37/64”49/64”
0.500.400.440.50
HexBody
1/2”5/8”3/4”15/16”
DSE-2-*DSE-4-*DSE-6-*DSE-8-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
DSL
G' G1'
C
C1
A
HEXWRENCH FLAT
E
PANEL THICKNESSD
BULKHEAD UNION ELBOW
PARTNo. EMin Orifice
DATube OD
CHexTube Nut
0.090.120.190.250.280.410.500.62
0.600.630.700.730.760.860.860.86
1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”
1.932.032.102.302.362.672.823.08
7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”
G1
0.620.750.790.890.910.941.061.11
Panel HoleDrill Size
Max PanelThickness
21/64”25/64”29/64”33/64”37/64”49/64”57/64”13/16”
0.600.610.610.740.740.740.500.66
WrenchFlat
3/8”1/2”1/2”5/8”5/8”13/16”15/16”11/16”
HexPanel Nut
1/2”9/16”5/8”11/16”3/4”15/16”11/16”13/16”
DSL-2-*DSL-3-*DSL-4-*DSL-5-*DSL-6-*DSL-8-*DSL-10-*DSL-12-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
C1
1.671.771.812.012.072.272.422.68
0.881.011.071.171.201.381.461.51
20
®
Series D
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 21
Fluid Connectors
DSS BULKHEAD FEMALE NPT CONNECTOR
PARTNo. TNPT
DATube OD
L1HexTube Nut
1/8”1/8”1/4”1/4”3/8”1/2”3/8”1/2”
EMin Orifice
0.090.190.190.280.280.280.410.41
1.231.321.321.451.451.451.651.65
1/8”1/4”1/4”3/8”3/8”3/8”1/2”1/2”
0.971.031.031.161.161.161.251.25
7/16”9/16”9/16”11/16”11/16”11/16”7/8”7/8”
LOAL
1.761.852.042.172.222.432.432.62
F Panel HoleDrill Size
Max PanelThickness
1.501.561.751.881.932.132.032.22
21/64”29/64”29/64”37/64”37/64”37/64”49/64”49/64”
0.500.400.400.440.440.440.500.50
HexBody
9/16”5/8”3/4”3/4”7/8”11/16”15/16”11/16”
HexPanel Nut
1/2”5/8”5/8”3/4”3/4”3/4”15/16”15/16”
DSS-2-2-*DSS-4-2-*DSS-4-4-*DSS-6-4-*DSS-6-6-*DSS-6-8-*DSS-8-6-*DSS-8-8-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
DSU
F
A E
L
HEX
D1
L1
D
BULKHEAD UNION
PARTNo. DD1ATube OD L1
HexTube Nut
0.600.630.700.730.760.860.860.861.04
EMin Orifice
0.090.120.190.250.280.410.500.630.80
1.231.271.321421.461.671.691.872.28
1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”1”
0.971.001.031.121.161.251.281.471.78
7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”11/4”
LOAL
2.022.112.272.392.462.802.873.113.79
F Panel HoleDrill Size
Max PanelThickness
1.501.591.691.811.882.002.072.312.81
21/64”25/64”29/64”33/64”37/64”49/64”57/64”11/64”121/64”
0.500.500.400.430.440.500.500.660.75
HexBody
1/2”9/16”5/8”11/16”3/4”15/16”11/16”13/16”15/8”
DSU-2-*DSU-3-*DSU-4-*DSU-5-*DSU-6-*DSU-8-*DSU-10-*DSU-12-*DSU-16-*
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
A E
LTD
FL1
HEXHEX1A
21
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 22
DTA
C
D
WRENCH FLAT
CC1 C1
CC1
AE
UNION TEE
PART No. C1D WrenchFlat
HexTube Nut
0.550.620.750.770.880.910.991.061.111.281.31
3/8”3/8”1/2”1/2”5/8”5/8”13/16”15/16”11/16”11/4”15/16”
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
5/16”7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”11/4”11/2”
DTA-1-*DTA-2-*DTA-3-*DTA-4-*DTA-5-*DTA-6-*DTA-8-*DTA-10-*DTA-12-*DTA-14-*DTA-16-*
ATube OD
0.050.090.120.190.250.280.410.500.620.720.88
EMin Orifice
0.710.881.011.071.171.201.401.471.521.681.81
C
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
0.440.600.630.700.730.760.860.860.860.861.04
DTF
A E
C
D T
WRENCH FLAT
C2
C1
FEMALE NPT RUN TEE
PART No. C1D WrenchFlat
HexTube Nut
0.700.760.880.941.031.021.111.25
C2
0.750.750.880.880.890.881.121.25
5/8”5/8”13/16”13/16”15/16”15/16”11/16”15/16”
1/8”1/4”1/4”3/8”3/8”1/2”1/2”3/4”
7/16”9/16”9/16”11/16”11/16”7/8”7/8”11/8”
DTF-2-2-*DTF-4-2-*DTF-4-4-*DTF-6-4-*DTF-6-6-*DTF-8-6-*DTF-8-8-*DTF-12-12-*
ATube OD
1/8”1/8”1/4”1/4“3/8”3/8”1/2”3/4”
TNPT
0.090.190.190.280.280.410.410.62
EMin Orifice
0.961.051.171.231.331.431.531.66
C
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
0.600.700.700.760.760.860.860.86
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position. 22
®
Series D
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 23
Fluid Connectors
DTH
WRENCH FLAT
A
C1 C1
D
C C
C2
T
E
FEMALE NPT BRANCH TEE
PART No. C1D WrenchFlat
HexTube Nut
0.700.760.880.941.020.991.021.121.251.121.251.28
C2
0.750.750.880.880.880.880.881.121.251.121.251.25
5/8”5/8”13/16”13/16”15/16”13/16”15/16”11/16”15/16”11/16”15/16”15/16”
1/8”1/4”1/4”3/8”3/8”1/2”1/2”1/2”1/2”5/8”3/4”7/8”
7/16”9/16”9/16”11/16”11/16”7/8”7/8”7/8”7/8”1”11/8”11/4”
DTH-2-2-*DTH-4-2-*DTH-4-4-*DTH-6-4-*DTH-6-6-*DTH-8-4-*DTH-8-6-*DTH-8-8-*DTH-8-12-*DTH-10-8-*DTH-12-12-*DTH-14-12-*
ATube OD
1/8”1/8”1/4”1/4“3/8”1/4“3/8”1/2”3/4”1/2”3/4”3/4”
TNPT
0.090.190.190.280.280.410.410.410.410.500.620.72
EMin Orifice
0.961.051.171.231.321.401.431.531.661.521.661.68
C
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
0.600.700.700.760.760.860.860.860.860.860.860.86
DTI
L
EA1 A
TUBE INSERT
PART No.A1
Tube ID
3/16”1/4”1/4”5/16”3/8”3/8”1/2”5/8”1”
1/8”1/8”3/16”1/4”3/16”1/4”3/8”1/2”3/4”
DTI-3-2-*DTI-4-2-*DTI-4-3-*DTI-5-4-*DTI-6-3-*DTI-6-4-*DTI-8-6-*DTI-10-8-*DTI-16-12-*
ATube OD
0.090.090.140.120.120.190.310.440.69
EMin Orifice
0.470.470.470.560.560.560.750.860.94
LOAL
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.23
Used with soft polymer tubing
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 24
DTK
DTN
A E
C1C1
D
T
C C
C2
WRENCH FLAT
W
MALE NPT RUN TEE
PART No. CD WrenchFlat
HexTube Nut
0.930.971.011.071.071.181.171.181.201.241.401.431.481.521.68
C1
0.670.710.750.780.780.890.880.880.910.940.981.201.061.111.28
C2
0.720.980.740.740.931.120.821.001.001.111.091.311.351.411.65
7/16”1/2”1/2”1/2”1/2”5/8”5/8”5/8”5/8”11/16”13/16”13/16”15/16”11/4”15/16”
1/8”1/8”3/16”1/4”1/4”1/4”5/16”5/16”3/8”3/8”1/2”1/2”5/8”3/4”7/8”
7/16”7/16”1/2”9/16”9/16”9/16”5/8”5/8”11/16”11/16”7/8”7/8”1”11/8”11/4”
DTK-2-2-*DTK-2-4-*DTK-3-2-*DTK-4-2-*DTK-4-4-*DTK-4-6-*DTK-5-2-*DTK-5-4-*DTK-6-4-*DTK-6-6-*DTK-8-6-*DTK-8-8*DTK-10-8-*DTK-12-12-*DTK-14-12-*
ATube OD
0.090.090.120.190.190.190.250.250.280.280.410.410.500.620.72
EMin Orifice
1/8”1/4”1/8”1/8”1/4”3/8”1/8”1/4”1/4”3/8”3/8”1/2”1/2”3/4”3/4”
TNPT
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
0.600.600.630.700.700.700.730.730.760.760.860.860.860.860.86
MALE NPT BRANCH TEE
PART No. C1D WrenchFlat
HexTube Nut
0.670.710.750.780.780.960.880.880.910.940.981.021.111.061.111.28
C2
0.720.930.750.750.931.320.821.001.001.111.091.311.401.341.401.65
7/16”1/2”1/2”1/2”1/2”13/16”5/8”5/8”5/8”11/16”13/16”13/16”11/16”15/16”11/16”11/4”
1/8”1/8”3/16”1/4”1/4”1/4”5/16”5/163/8”3/8”1/2”1/2”1/2”5/8”3/4”7/8”
7/16”7/16”1/2”9/16”9/16”9/16”5/8”5/8”11/16”11/16”7/8”7/8”7/8”1”11/8”11/4”
DTN-2-2-*DTN-2-4-*DTN-3-2-*DTN-4-2-*DTN-4-4-*DTN-4-8-*DTN-5-2-*DTN-5-4-*DTN-6-4-*DTN-6-6-*DTN-8-6-*DTN-8-8-*DTN-8-12-*DTN-10-8-*DTN-12-12-*DTN-14-12-*
ATube OD
1/8”1/4”1/8”1/8”1/4“1/2”1/8”1/4”1/4”3/8”3/8”1/2”3/4”1/2”3/4”3/4”
TNPT
0.090.090.120.190.190.190.190.250.280.280.410.410.410.500.620.72
EMin Orifice
0.930.971.001.071.071.261.171.181.201.201.401.431.521.471.521.68
C
0.600.600.630.700.700.700.730.730.760.760.860.860.860.860.860.86
WRENCH FLAT
D
A E
C
D T
C2
C1
CC1
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position. 24
®
Series D
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 25
Fluid Connectors
DTR
D
A
C
D1
WRENCH FLAT
CC1 C1
C2C1
EA1
REDUCING UNION TEE
PART No. C2D1D WrenchFlat
HexTube Nut
1.201.281.281.361.411.521.611.721.72
5/8”13/16”13/16”15/16”11/16”11/16”15/16”15/16”15/16”
3/8”1/2”1/2”5/8”3/4”3/4”1”1”1”
1/4”1/4”3/8”3/8”3/8”1/2”3/8”1/2”3/4”
11/16”7/8”7/8”1”11/8”11/8”11/2”11/2”11/2”
9/16”9/16”11/16”11/16”11/16”7/8”11/16”7/8”11/8”
DTR-6-6-4-*DTR-8-8-4-*DTR-8-8-6-*DTR-10-10-6-*DTR-12-12-6-*DTR-12-12-8-*DTR-16-16-6-*DTR-16-16-8-*DTR-16-16-12-*
ATube OD
A1Tube OD
Hex 1Tube Nut
0.190.190.280.280.280.410.280.410.62
EMin Orifice
0.910.980.981.061.111.111.311.311.31
C1
1.201.391.391.471.521.521.811.811.81
C
0.760.860.860.860.860.861.041.041.04
0.700.700.760.760.760.860.760.860.86
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
TYPE 1
PART No. C2D1DWrenchFlat
HexTube Nut
1.471.411.52
15/16”11/8”11/8”
5/8”3/4”3/4”
1/2”3/8”5/8”
1”11/8”11/8”
7/8”11/16”1”
DTR-10-8-8-*DTR-12-6-6-*DTR-12-10-10-*
ATube OD
A1Tube OD
Hex 1Tube Nut
0.410.280.50
EMin Orifice
1.061.111.11
C1
1.471.521.52
C
0.860.860.86
0.860.760.86
PART No. C2D1DWrenchFlat
HexTube Nut
1.281.72
11/8”15/16”
1/2”1”
3/8”3/4”
7/8”11/8”
11/16”11/8”
DTR-8-6-8-*DTR-16-12-16-*
ATube OD
A1Tube OD
Hex 1Tube Nut
0.280.62
EMin Orifice
0.981.31
C1
1.391.81
C
0.861.04
0.760.86
PART No. C3D1DWrenchFlat
HexTube Nut
1.471.521.72
15/16”11/16”15/16”
5/8”3/4”1”
1/2”1/2”3/4”
1”11/8”11/2”
7/18”7/8”11/8”
DTR-10-8-6-*DTR-12-8-6-*DTR-16-12-6-*
ATube OD
A1Tube OD
3/8”3/8”3/8”
A2Tube OD
Hex 1Tube Nut
11/16”
11/16”
Hex 2Tube Nut
0.280.280.28
EMin
1.111.061.11
C2
1.061.111.31
C1
1.471.521.81
C
0.760.760.76
D2
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
0.860.861.04
0.860.860.86
D
A1A
C
D1
WRENCH FLAT
C2C1 C1
C2C1
E
D D1
A1E
C
WRENCH FLAT
C2C1 C1
CC1
A
A1
A2
A
C
D2
D1D
WRENCH FLAT
C2C1 C1
C3C1
E
Type 1
(Type 2 Shown)
Type 2
Type 3 Type 4
TYPE 2
TYPE 3
TYPE 4
25
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 26
DUA
LD D
HEXF
A E
UNION
PART No.LOAL
D HexBody
HexTube Nut
0.991.401.471.611.691.782.022.052.112.172.58
5/16”7/16”7/16”1/2”9/16”5/8”13/16”15/16”11/16”13/16”13/16”
1/16”1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”7/8”1”
5/16”7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”11/4”11/2”
DUA-1-*DUA-2-*DUA-3-*DUA-4-*DUA-5-*DUA-6-*DUA-8-*DUA-10-*DUA-12-*DUA-14-*DUA-16-*
ATube OD
0.050.090.120.190.250.280.410.500.620.720.88
EMin Orifice
0.690.880.951.031.111.191.221.251.311.371.59
F
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
0.440.600.630.700.730.760.860.860.860.861.04
DUCAN 37° FLARE UNION
PART No. FD HexBody
HexTube Nut
0.991.121.191.221.271.271.401.441.541.741.94
LOAL
1.241.381.481.521.561.561.811.841.952.142.43
7/16”1/2”1/2”9/16”5/8”5/8”13/16”15/16”15/16”11/8”13/16”
1/8”1/8”1/4”5/16”3/8”3/8”1/2”5/8”5/8”3/4”1”
7/16”7/16”9/16”5/8”11/16”11/16”7/8”1”1”11/8”11/2”
DUC-2-2-*DUC-2-4-*DUC-4-4-*DUC-5-5-*DUC-6-4-*DUC-6-6-*DUC-8-8-*DUC-10-8-*DUC-10-10-*DUC-12-12*DUC-16-16-*
ATube OD
1/8”1/4”1/4”5/16“1/4”3/8”1/2”1/2”5/8”3/4”1”
ANTube Size
5/16”-247/16”-207/16”-201/2”-207/16”-209/16”-183/4”-163/4”-167/8”-1411/16”-1215/16”-12
TStraight Thread
0.090.090.180.230.280.280.400.500.480.610.89
EMin Orifice
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
0.600.600.700.730.760.760.860.860.860.861.04
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
A
37.5
L
F
D
HEX
T
E
26
®
Series D
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 27
37.5
F
A
L
T
HEX
D
L1
E
BULKHEAD AN 37° FLARE UNION
A1
F
LD D1
HEX
A E
REDUCING UNION
PART No.E
Min OrificeD Hex
BodyHex
Tube Nut
0.050.050.090.050.090.120.190.090.190.250.090.190.280.280.410.190.280.410.500.620.410.62
F
0.810.860.920.910.971.001.081.061.121.161.131.161.221.251.251.251.311.311.311.381.541.50
LOAL
1.221.271.441.351.521.551.661.611.701.741.781.851.911.942.051.932.002.112.112.142.402.39
7/16”7/16”7/16”1/2”1/2”1/2”9/16”5/8”5/8”5/8”13/16”13/16”13/16”15/16”15/16”11/16”11/16”11/16”11/16”13/16”13/8”13/8”
1/8”3/16”3/16”1/4”1/4”1/4”5/16”3/8”3/8”3/8”1/2”1/2”1/2”5/8”5/8”3/4”3/4”3/4”3/4”7/8”1”1”
7/16”1/2”1/2”9/16”9/16”9/16”5/8”11/16”11/16”11/16”7/8”7/8”7/8”1”1”11/8”11/8”11/8”11/8”11/4”11/2”11/2”
DUR-2-1-*DUR-3-1-*DUR-3-2-*DUR-4-1-*DUR-4-2-*DUR-4-3-*DUR-5-4-*DUR-6-2-*DUR-6-4-*DUR-6-5-*DUR-8-2-*DUR-8-4-*DUR-8-6-*DUR-10-6-*DUR-10-8-*DUR-12-4-*DUR-12-6-*DUR-12-8-*DUR-12-10-*DUR-14-12-*DUR-16-8-*DUR-16-12-*
ATube OD
1/16”1/16”1/8”1/16”1/8”3/16”1/4”1/8”1/4“5/16”1/8”1/4“3/8”3/8”1/2”1/4”3/8”1/2”5/8”3/4”1/2”3/4”
A1Tube OD
5/16”5/16”7/16”5/16”7/16”1/2”9/16”7/16”9/16”5/8”7/16”9/16”11/16”11/16”7/8”9/16”11/16”7/8”1”11/8”7/8”11/4”
HexTube Nut
0.440.440.600.440.600.630.700.600.700.730.600.700.760.760.860.700.760.860.860.860.860.86
D1
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
0.600.630.630.700.700.700.730.760.760.760.860.860.860.860.860.860.860.860.860.861.041.04
Fluid Connectors
DUE
DUR
PART No.Panel HoleDrill Size
FANTube Size
Max PanelThickness
D
29/64”37/64”37/64”49/64”11/16”121/64”
0.400.440.440.500.660.75
17.4219.2319.2321.5421.625.4
0.180.280.280.400.610.88
1/4”3/8”3/8”1/2”3/4”1’
0.700.760.760.860.861.04
1.831.961.962.192.713.16
DUE-4-4-*DUE-6-4-*DUE-6-6-*DUE-8-8-*DUE-12-12-*DUE-16-16-*
HexTube Nut
EMinOrifice
HexBody
LOAL
7/16”-207/16”-209/16”-183/4”-1611/16”-1215/16”-12
TStraightThread
5/8”3/4”3/4”15/16”13/16”15/8”
1.031.161.161.261.471.78
L1
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
1/4”1/4”3/8”1/2”3/4”1”
2.122.262.252.593.113.64
ATube OD
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.27
610202_text.qxd7:802183aa text.qxd 6/21/10 2:17 PM Page 28
®
Series D
BI-LOK to FEMALE NPT
BI-LOK to MALE NPT
DHATube Stub toMale NPT Adapter Page 11
DCTMale NPT Connector Page 8
DSLBulkheadUnion Elbow Page 20
DCTZThermocouple Connector Page 10
DSCBulkhead MaleNPT Connector Page 19
DLNMale NPT Elbow Page 14
DLFFemale NPT Elbow Page 13
DTFFemale NPT Run Tee Page 22
DTHFemale NPT Branch Tee Page 23
DTKMale NPT Run Tee Page 24
DTNMale NPT Branch Tee Page 24
DSAFemale NPTConnector Page 18-19
DSSBulkhead FemaleNPT Connector Page 21
DHCTube Stub toFemale NPT Adapter Page 12
DUAUnion Page 26
DSUBulkhead Union Page 21
DURReducing Union Page 27
DLAUnion Elbow Page 12
DTAUnion Tee Page 22
DTRReducing Union Tee Page 25
DXAUnion Cross Page 28
Fluid Connectors
BI-LOK UNION
DX
A
C
DWRENCH FLAT
C
C1C1
C
C
C1
C1
AE
UNION CROSS
PART No. C1D WrenchFlat
HexTube Nut
0.620.750.780.880.910.981.061.111.31
3/8”1/2”1/2”5/8”5/8”13/16”15/16”11/16”15/16”
1/8”3/16”1/4”5/16”3/8”1/2”5/8”3/4”1”
7/16”1/2”9/16”5/8”11/16”7/8”1”11/8”11/2”
DXA-2-*DXA-3-*DXA-4-*DXA-5-*DXA-6-*DXA-8-*DXA-10-*DXA-12-*DXA-16-*
ATube OD
0.090.120.190.250.280.410.500.620.88
EMin Orifice
0.881.011.071.171.201.401.471.521.81
C
* Add Suffix “SS” for 316 Stainless Steel or “B” for Brass.
0.600.630.700.730.760.860.860.861.04
Dimensions are provided in inches and are for reference only, subject to change. Dimensions shown are with the nut in thefinger-tight position.
A GLOBAL CONNECTION
BI-Lok Tube Fittings are manufac-tured in four State-of-the-art facili-ties, in two countries, and are mar-keted worldwide through a networkof authorized stocking distributorsand representatives.
In today’s business environment,success is dependant upon the truecreation of value.
For over 75 years, Generant, aleading designer and manufacturerof pressure and flow control prod-ucts, has built a reputationsynonymous with innovative andadvanced design, appl icat ionengineering expertise, quality man-ufacturing and unparalleled service.
In this tradition, BI-Lok Series DDual Ferrule Tube Fittings repre-sent a high quality, cost effective,design solution to instrument gradefluid connector applications.BI-Lok® is a registered trademark of the Ihara Science Corporation, Tokyo, Japan. 28
610202_covs.qxd7:802183aa covs.qxd 6/21/10 1:12 PM Page 2
Series D Dual FerruleInstrument Tube Fittings
®
Fluid Connectors
1865 Route 23 South • P.O. Box 768 • Butler, NJ 07405 • Tel: 973.838.6500 • Fax: 973.838.4888© 2002 Generant Company
www.generant.com
610202_covs.qxd7:802183aa covs.qxd 6/21/10 1:12 PM Page 1