sensorkit x ì - amazon s3...ky- ì ï heartbeat sensor module if a finger is palced between the...

11
Sensorkit X40 You can find code-examples and soſtware on our website www.joy-it.net/sensorkit/

Upload: others

Post on 12-May-2020

0 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

Sensorkit X40

You can find code-examples and software on our website

www.joy-it.net/sensorkit/

Page 2: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

Pin-Assignment

The pin-assignment is also shown in the description of the sensors.

Please find the used numbering on the left side.

It is marked that the contact-pins are pointing away, to the right, from

the board.

We recommend to use Dupontcables to connect the sensors to a bread-

board or directly to the experimental board.

Dear customer,

thank you for purchasing our product.

Please find our instructions below:

Page 3: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

KY-001 Temperature Sensor Module

Chipset: DS18B20 | Communicationprotocoll: 1-Wire

9- 12Bit exact temperature measurement in measurement-range from –55°C to +125°C

① - Signal

② - +V

③ - GND

KY-002 Shock-Switch Module

The contact between the two input pins is connected when a shock is detected

① - Signal

② - +V

③ - GND

KY-003 Hall Magnetic-Field-Sensor Module Chipset A3141 Sensortype: Hall Effect Transistor/Switch The transistor connects when the module is near by a mag-netic field. This can be measured as an analog value at the signal output.

① - Signal

② - +V

③ - GND

KY-004 Button-Module While pressing the button, two signal outputs are connected

① - GND

② - +V

③ - Signal

KY-005 Infrared Transmitter Module A diode which emits infrared light

Depending on the input voltage, a resistor is necessary

① - GND

② - [N.C.]

③ - Signal

Page 4: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

KY-006 Passive Piezo-Buzzer Module Controlled with PWM-signals in different frequencies, different sounds can be produced.

① - GND

② - +V

③ - Signal

KY-009 RGB LED SMD Module LED-Module which contains a red, blue and green LED. These are connected with a common cold cathode.

Depending on the input voltage, a resistor is necessary

① - GND

② - LED Green

③ - LED Red

④ - LED Blue

KY-010 Light-barrier-Module The connection between to input pins is interrupted if the light-barrier is interrupted.

① - Signal

② - +V

③ - GND

KY-011 2-color [Red+Green] 5mm LED Module LED-Module which contains a red and a green LED. These are connected with a common cathode. Depending on the input voltage, a resistor is necessary

① - LED Green

② - LED Red

③ - GND

KY-012 Active Piezo-Buzzer Module Tonfrequenz: 2,5kHz voltage-powered, this active buzzer creates a sound with a frequency of 2,5 kHz

① - GND

② - +V

③ - Signal

Page 5: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

KY-013 Temperature-Sensor Module Temperature measuring range: -55°C / +125°C

This module contains a NTC Thermistor—this has a declining resistor-value when the temperature is rising.

① - +V

② - GND

③ - Signal

KY-015 Combination-Sensor Temperature+Humidity Chipset: DHT11 | Communicationprotocoll: 1-Wire Measuring range humidity: 20-90%RH Measuring range temperature: 0-50°C

① - GND

② - +V

③ - Signal

KY-016 RGB 5mm LED Module LED-Module which contains a red, blue and green LED which are connected with a common cathode. Depending on the input voltage, a resistor can be necessary

① - GND

② - LED Red

③ - LED Green

④ - LED Blue

KY-017 Tilt Switch Module

Depending on the tilt, a switch connects the input pins.

① - Signal

② - +V

③ - GND

KY-018 Photoresistor Module Conains a LDR-resistor—ist resistor-value is declining if the environment is getting brighter.

① - GND

② - +V

③ - Signal

Page 6: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

KY-019 5V Relais Module Voltage range: 240VAC / 10A | 28VDC / 10A A relais to toggle higher voltages with a 5V output. Security information: VDC =< 30V Higher voltages can result in extremely dangerous injuries.

① - [ - ]

② - [ + ]

③ - Signal

KY-020 Tilt-Switch-Module Depending on the tilt, a switch connects the input pins.

① - GND

② - +V

③ - Signal

KY-021 Mini Magnet Reed Module If a magnetic field is detected, both input pins are connected

① - GND

② - +V

③ - Signal

KY-022 Infrared Receiver Module Carrier frequency: 38kHz Can receive infared signals and writes them to the signal output as an digital sequence.

① - Signal

② - +V

③ - GND

KY-023 Joystick Module (XY-Axes) X and Y position of the joystick are transferred as analog voltage to the output pins.

① - Button

② - Y-Position

③ - X-Position

④ - +V

⑤- GND

Page 7: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

KY-024 Linear magnetic Hall Sensor Chipset: A3141 | OP-Amplifier: LM393 The magnetic field is measured by the sensor and transferred as an analog voltage. The sensitivity of the sensor can be adjusted with the potentiometer.Das Magnetfeld wird vom Sensor gemessen und als analoger Spannungswert ausgegeben. Die Empfindlichkeit des Sensors kann mittels des Potentiometers geregelt werden. Digitaler Ausgang: Wird eine Flame erkannt, wird hier ein Signal ausgegeben Analoger Ausgang: Direkter Messwert der Sensoreinheit

① - digital signal

② - +V

③ - GND

④ - analog signal

KY-025 Reed Module If a magnetic field is detected, its given out to the digital output.

① - digital signal

② - +V

③ - GND

④ - analog signal

KY-026 Flame-Sensor Module The mounted photodiode is sensitive to the spectral range of light which are created by flames. Digitaler Ausgang: A signal is given out if a flame is detected Analoger Ausgang: Direct measurement value of the sensor

① - digital signal

② - +V

③ - GND

④ - analog signal

KY-027 Magic Light Cup Module The LED is turned on or off by concussion. The signal, when the led is on, is given out to a signal output. Je nach Eingangsspannung, werden Vorwiderstände benötigt

① - LED

② - Signal

③ - +V

④ - GND

KY-028 Temperature Sensor Module (Thermistor) Temperature measurement range: -55°C / +125°C This module contains a NTC Thermistor—it has a declining resistor value on a raising temperature. Analog output: direct measurement of the temperature sensor Digital otuput: If the temperature is rising above a limit, its given out here. The luimit can be controlled with the potentiometer.

① - digital signal

② - +V

③ - GND

④ - analog signal

Page 8: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

KY-029 2-color [Red+Green] 3mm LED Module LED-Module which contains a red and a green LED. These are connected with a common cathode. Depending on the input voltage, a resistor can be necessary

① - LED Gren

② - LED Red

③ - GND

KY-031 Knock-Sensor Module If the sensor is exposed to a knock/shock, both output pins are connected.

① - GND

② - +V

③ - Signal

KY-032 Obstacle Detection Module If the emitted infared light hits an obstacle, the light is being reflected and detected by the photodiode. The detection rage can be controlled with the two controllers.

① - [EN]

② - digital signal

③ - +V

④ - GND

KY-033 Tracking Sensor Module The sensor-module recognizes if a light-reflecting or light-absorbing surface is in front of the sensor. The digital output is giving out the result. This e.g. can be used to follow a line. The sensitivity of the sensor can be controlled with the con-troller.

① - Signal

② - +V

③ - GND

KY-034 7 color LED Flash-Module If this module is powered, a sequence of color-changes is emitted by the LED. This contains 7 different colors. Depending on the input voltage, a resistor can be necessary

① - GND

② - [N.C.]

③ - Signal

Page 9: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

KY-035 Bihor Magnet Sensor Module Chipset: AH49E The sensor gives an analog voltage to ist output which shows the inten-sitiy of a magnetic field.

① - Signal

② - +V

③ - GND

KY-036 Metal-Touchsensor Module Gives out a signal if the front metal tip is touched. The sensitivity can be controlled with the controller. Digital output: If a touch is detected, its given out here Analog output: direct measurement value of the sensor

① - digital signal

② - +V

③ - GND

④ - analog signal

KY-037 Microphone Sensor Module [high sensitivity] Analog output: direct microphone-signal as voltage level Digital output: A limit can be set with the potentiometer. The digital output toggles if the limit is reached.

① - digital signal

② - +V

③ - GND

④ - analog signal

KY-038 Microphone Sound Sensor Module Analog output: direct microphone-signal as voltage level Digital output: A limit can be set with the potentiometer. The digital output toggles if the limit is reached.

① - digital signal

② - +V

③ - GND

④ - analog Signal

KY-039 Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput.

① - Signal

② - +V

③ - GND

Page 10: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

KY-040 Rotary Encoder The current position of the rotary switch is given out coded on the output.

① - [CLK]

② - [DT]

③ - Button

④ - +V

⑤ - GND

KY-050 Ultrasonic-Distancesensor If a signal (falling peak) is given to the trigger-input, a distance measurement is executed and given out as a PWM-TTL signal to the echo-output. Measureable distance: 2cm—300cm Measurement-resolution: 3mm

① - GND

② - Echo

③ - Trigger

④ - +V

KY-051 Voltage Translator / Level Shifter This level-shifter transfers digital signals from a voltage into another. 4 channels are available which can be used.

PIN-assignment is printed to the

module-board

KY-052 Pressuresensor / Temperaturesensor [BMP180] This pressuresensor measures the air pressure and gives out the result coded to the I2C-Bus.

A software is necessary to use this sensor

① - +5V

② - GND

③ - [SCL]

④ - [SDA]

⑤ - +3V3

KY-053 Analog Digital Converter With appropriate commands to the I2C-Bus, up to 4 analog inputs can be measured to an accuracy of up to 16 Bit. The result is given out coded to the I2C-Bus. A software is necessary to use this sensor

PIN-assignment is printed to the

module-board

Page 11: Sensorkit X ì - Amazon S3...KY- ì ï Heartbeat Sensor Module If a finger is palced between the diode and the phototransistor, the pulse can be measured at the signaloutput. ① -

Software und Codexamples

On our website

www.joy-it.net/sensorkit/

we offer a collection of code-examples for e.g. the Arduino and the Raspberry Pi.

For some modules (e.g. the analog-digital-converter) you need an additional software to

read the measurement results.

You can find these also on our website.

Voltage Level

Depending on the experimentalboard/microconrollersystem you use, different voltagelevels

can occur.

Please note the voltage supply and also the compatibility of the input voltage of the used

systems.

For example, older Arduino-Systems tolerate 5V input voltages, but to the Raspberry Pi,

signals above 3.3V must not be applied.

You can find further informations in your systems manual/datasheet.

To avoid the mentioned problem, you can find the KY-051 Voltage Translator / Level Shifter in

the set. This allows you a safe operation on structures with different voltage levels.

You can find an accurate listing of which sensor can be used with which voltage on our website

www.joy-it.net/sensorkit/