self-learning toyota/lexus key programmer with key emulation · 2018-02-10 · tkp-2 v.1.3 1...
TRANSCRIPT
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
Self-learning TOYOTA/LEXUS key
programmer
with key emulation
Supported models:
All of Toyota/Lexus models equipped with KEYLESS-GO system, from 2008 m.y. till 2018
Working principle:
Device receives digital data signal from SMART module and then emulates ignition key(card) to
check whether immobilizer system is working properly. The following types of keys are supported:
94/D4/98/88/A8/A9
Also you can add new key if you need it.
Appearance:
After device connected to OBD, the following menu will appear.
Picture 1
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
If connection to SMART module was successful and necessary data received, the following menu
will appear:
Picture 2
In case if current SMART module is not supported –“LEARNING...” message will appear. Please wait
approx. 1- 2 minutes to let the device to analyze received data. Next time when device will be
connected to the same type of SMART module, it will work immediately. It means device already
learned and stored new type of SMART module.
CHECK (Disarming )
Needed for CAMRY, PRADO and AVENSIS models
1. Connect main cable to the device
2. Connect device to OBD socket (located in the left of driver’s legroom)
3. Press once START/STOP button or press brake pedal to “wakeup” the car
4. Select CHECK item in the device’s menu
5. Doors unlocks and OK !!! message will appear on display
6. Then press CONNECT
CONNECT (Engine start)
1. Connect main cable to the device
2. Connect device to OBD socket (located in the left of driver’s legroom)
3. Press once START/STOP button or press brake pedal to “wakeup” the car
4. Select CONNECT item in the device’s menu
5. If “LEARNING...” message appeared, please wait till learning finishes (approx. 1-2 minutes)
6. When “BRING TO BUTTON” message appeared – press and keep brake pedal, touch
START/STOP button by the device’s backside, as pictured(Pic.2). ANTENNA icon (( Y ))
should blink.
7. Press START/STOP to start a car
8. Press EXIT in menu and disconnect device from OBD socket
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
ADD (Add new key)
1. Connect main cable to the device
2. Connect device to OBD socket (located in the left of driver’s legroom)
3. Press once START/STOP button or press brake pedal to “wakeup” the car
4. Select ADD item in the device’s menu
5. If “LEARNING...” message appeared, please wait till learning finishes (approx. 1-2 minutes)
6. When “BRING TO BUTTON” message appeared – press and keep brake pedal, touch
START/STOP button by the device’s backside, as pictured (Pic.2). ANTENNA icon (( Y ))
should blink.
7. After sound signal, take device out of START/STOP button, and touch button with the key
you need to program, after a while you will hear programming confirmation sound.
8. Press EXIT in menu and disconnect device from OBD socket
To start the car with A9 RX keys (from 09.2015), LC200 (from 2016), LC570 (from 2016),
Prius (from 2016), C-HR etc.) In some of these models, when car is locked the Central
Gateway blocks Diagnostic bus (OBD-2 socket) access. To unlock the car, there are
alternative places to connect to the SMART-BOX ECU:
Connecting location for Land Cruiser 200 from 2016 m.y.
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
Connecting location for Lexus RX from 09.2015 m.y.
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
Number 10 (Certification ECU)
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
pin 14- CAN high (Purple)
pin 15- CAN low (White)
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
Connecting location for Toyota C-HR
Number 8 (Certification ECU)
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
Pin 1- CAN High (Red)
Pin 2- CAN Low (SkyBlue)
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
Connecting location for Corolla/Auris
Number 6 (Certification ECU)
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
pin 14- CAN high (Purple)
pin 15- CAN low (White)
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
Connecting location for RAV4 from 2016 m.y.
Number 5 (Certification ECU)
TKP-2 v.1.3
1 июня, 2015
Посетите наш сайт www.autokeydevices.com, ознакомьтесь с новыми продуктами!
pin 14- CAN-H high (RED)
pin 15- CAN-L low (White)
Troubleshooting
• If you get (ERROR) message please check OBD connector, check if the car is not in “sleep”
mode and try once again.
• In case of errors during execution of CONNECT command – please check if the original
working key is not present in the car, take it out or remove battery from this key.
• If you cannot program a key with ADD command, it means key is not blank or does not fit to
the exact car.