seegull mx 2.6.3.0 release notes rev x
TRANSCRIPT
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 1 of 47
SeeGull® MX Product Release Notes
Release 2.6.3.0
Document Number: 14RN55-00M Revision X
March 5, 2013
Restrictions: This document contains proprietary information that is protected by copyright; it is intended for use by PCTEL and its customers only. It is not to be disclosed to a third party. All rights reserved. No part of this document may be photocopied or reproduced in any way without the prior written permission of PCTEL RF Solutions. The information contained in this document is subject to change without notice. PCTEL RF Solutions makes no warranty of any kind with regard to this document. PCTEL RF Solutions shall not be liable for errors or omissions contained herein or for incidental or consequential damages in connection with the use of this document.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 2 of 47
COMMENT ON KNOWN DEFECTS AND OTHER ERRATA This document lists problems known to be associated with the current release. PCTEL RF Solutions is committed to releasing defect free products, and appreciates any reports of issues or assistance in the identification of issues. Problems are prioritized and queued for remedy.
PCTEL RF Solutions is always interested in your feedback concerning our products, and the features or additions that would make them better. Please feel free to contact PCTEL RF Solutions using the support information below with any suggestions for improvements.
Trademarks © 2013 PCTEL, Inc. All rights reserved. PCTEL, SeeGull®, SeeHawk®, InSite®, CLARIFY®, the CLARIFY® logo and the PCTEL logo are registered trademarks of PCTEL, Inc. All other trademarks are property of their respective owners.
Notices and Warranty Information The information in this document is subject to change without notice and should not be construed as commitment by PCTEL. PCTEL assumes no responsibility or makes no warranties for any errors that may appear in this document and disclaims any implied warranty of merchantability or fitness for a particular purpose.
Copyright Information No part of this document may be used or copied in any form or any means without prior written consent of PCTEL.
All Rights Reserved
Copyright 1997-2013
PCTEL, Inc. RF Solutions 20410 Observation Drive, Suite 200 Germantown, MD 20876 USA Phone: +1 301 515 0036 Fax: +1 301 515 0037
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 3 of 47
Table of Contents 1.0 Current Release Notes ............................................................................... 4 2.0 Previous Release Notes ............................................................................. 8 2.1 Release 2.6.2.0 (November 30, 2012) .............................................................. 8 2.2 Release 2.6.1.0 (October 24, 2012) ................................................................ 12 2.3 Release 2.4.0.0 (June 8, 2012) ........................................................................ 16 2.4 Release 2.1.0.1 (July 25, 2011) ....................................................................... 20 2.5 Release 2.1.0.0 (June 28, 2011) ..................................................................... 23 2.6 Release 2.0.0.2 (June 17, 2011) ..................................................................... 26 2.7 Release 2.0.0.1 (June 10, 2011) ..................................................................... 28 2.8 Release 1.1.1.1 (May 16, 2011) ...................................................................... 32 2.9 Release 1.1.1.0 (May 02, 2011) ...................................................................... 34 2.10 Release 1.3 (April 11, 2011) ............................................................................. 36 2.11 Release 1.2 (February 8, 2011) ....................................................................... 39 2.12 Release 1.1 (January 21, 2011) ...................................................................... 42 2.13 Release 1.0 (January 14, 2011) ...................................................................... 45
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 4 of 47
1.0 Current Release Notes
The release consists of the following components:
Component Name Filename Version
SW Release 2.6.3.0
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.10
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev M
SeeGull Master API SeeGullMaster.dll 1.4.0.1
SeeGull API Reference SeeGull API Reference.chm 1.4
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
TD-LTE 0001 000Bh TD-LTE Support 0005 000Bh TD-LTE MIB/SIB Decoding 000B 000Bh TD-LTE Blind Scanning 000C 000Bh 002C 000Bh
TD-LTE Enhanced Signal Scanning TD-LTE Enhance Signal 2Rx Scanning
000D 000Bh
TD-LTE Power Analyzer
LTE 0001 000Ah FD-LTE Support 0005 000Ah 000B 000Ah
FD-LTE MIB/SIB Decoding FD-LTE Blind Scanning
000C 000Ah 002C 000Ah
FD-LTE Enhanced Signal Scanning FD-LTE Enhanced LTE Signal 2Rx Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h 0005 0001h
GSM C/I Scanning GSM Normal BCCH
000B 0001h 000D 0001h
GSM Blind Scanning GSM Clarify Scanning
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 5 of 47
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 0005 0004h
3GPP WCDMA Pilot Scanning 3GPP WCDMA BCH Decoding
0008 0004h 3GPP WCDMA Extended Dynamic Range 000B 0004h 000D 0004h
3GPP WCDMA Blind Scanning 3GPP WCDMA Clarify Pilot Scanning
CDMA
0001 0003h IS-95 Support 0003 0003h IS-95 Pilot Scanning 0008 0003h 000B 0003h
IS-95 Extended Dynamic Range IS-95 Blind Scanning
0001 0005h IS-2000 Support 0003 0005h IS-2000 Pilot Scanning 0008 0005h 000B 0005h
IS-2000 Extended Dynamic Range IS-2000 Blind Scanning
EVDO
0001 0006h IS-856 Support 0003 0006h IS-856 Pilot Scanning 0008 0006h 000B 0006h
IS-856 Extended Dynamic Range IS-856 Blind Scanning
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
NEW FEATURES
None
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 6 of 47
Messages Supported
Scanning Messages o Enhanced Power Scan
o RSSI Scan
o GSM Color Code Scan including BCCH
o GSM Clarify Scan
o LTE Enhanced Top N Signal Scan
o CDMA Top N Pilot Scan
o EVDO Top N Pilot Scan
o WCDMA Top N Pilot Scan including BCH
o WCDMA Clarify Pilot Scan
o TD-LTE Power Analyzer Scan
o LTE/WCDMA/GSM/CDMA/EVDO Blind Scan
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o GPS Information
o Inquiry
o Operation Mode
o Product Information
o Reset Device
o Stop Scan
NOTES The GPS LED turns purple if the GPS module is not trained. The GPS may retrain itself
after software upgrades from very early software versions on the MX. Training requires 20 minutes.
The bootup time for the MX scanner is approximately 90 sec.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 7 of 47
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
For TD-LTE, the SIB message may only contain the first 20 to 40 msec of the message if the window length is >= 40 msec. [#3519.]
RF board enumeration may fail on rare occasion. This is indicated by the amber color of the Power LED. This is corrected by recycling power. [#3271]
Scanner RF firmware may get corrupted during the firmware download. This problem corrects itself upon retry. [#3315].
Scanner Power/Timing firmware info may return all zeros in Extended Inquiry after firmware download. This problem corrects itself upon retry. [#3385].
PROBLEMS RESOLVED IN THIS RELEASE
Scanner stops responding in the presence of a large bursty interferer when running GSM Color Code scans. [#3613]
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 8 of 47
2.0 Previous Release Notes
2.1 Release 2.6.2.0 (November 30, 2012)
The release consists of the following components:
Component Name Filename Version
SW Release 2.6.2.0
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.10
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev K
SeeGull Master API SeeGullMaster.dll 1.4.0.1
SeeGull API Reference SeeGull API Reference.chm 1.4
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
TD-LTE 0001 000Bh TD-LTE Support 0005 000Bh TD-LTE MIB/SIB Decoding 000B 000Bh TD-LTE Blind Scanning 000C 000Bh 002C 000Bh
TD-LTE Enhanced Signal Scanning TD-LTE Enhance Signal 2Rx Scanning
000D 000Bh
TD-LTE Power Analyzer
LTE 0001 000Ah FD-LTE Support 0005 000Ah 000B 000Ah
FD-LTE MIB/SIB Decoding FD-LTE Blind Scanning
000C 000Ah 002C 000Ah
FD-LTE Enhanced Signal Scanning FD-LTE Enhanced LTE Signal 2Rx Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h 0005 0001h
GSM C/I Scanning GSM Normal BCCH
000B 0001h 000D 0001h
GSM Blind Scanning GSM Clarify Scanning
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 9 of 47
WCDMA
0001 0004h 3GPP WCDMA 0003 0004h 0005 0004h
3GPP WCDMA Pilot Scanning 3GPP WCDMA BCH Decoding
0008 0004h 3GPP WCDMA Extended Dynamic Range 000B 0004h 000D 0004h
3GPP WCDMA Blind Scanning 3GPP WCDMA Clarify Pilot Scanning
CDMA
0001 0003h IS-95 Support 0003 0003h IS-95 Pilot Scanning 0008 0003h 000B 0003h
IS-95 Extended Dynamic Range IS-95 Blind Scanning
0001 0005h IS-2000 Support 0003 0005h IS-2000 Pilot Scanning 0008 0005h 000B 0005h
IS-2000 Extended Dynamic Range IS-2000 Blind Scanning
EVDO
0001 0006h IS-856 Support 0003 0006h IS-856 Pilot Scanning 0008 0006h 000B 0006h
IS-856 Extended Dynamic Range IS-856 Blind Scanning
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
NEW FEATURES
None
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 10 of 47
Messages Supported
Scanning Messages o Enhanced Power Scan
o RSSI Scan
o GSM Color Code Scan including BCCH
o GSM Clarify Scan
o LTE Enhanced Top N Signal Scan
o CDMA Top N Pilot Scan
o EVDO Top N Pilot Scan
o WCDMA Top N Pilot Scan including BCH
o WCDMA Clarify Pilot Scan
o TD-LTE Power Analyzer Scan
o LTE/WCDMA/GSM/CDMA/EVDO Blind Scan
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o GPS Information
o Inquiry
o Operation Mode
o Product Information
o Reset Device
o Stop Scan
NOTES The GPS LED turns purple if the GPS module is not trained. The GPS may retrain itself
after software upgrades from very early software versions on the MX. Training requires 20 minutes.
The bootup time for the MX scanner is approximately 90 sec.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 11 of 47
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
For TD-LTE, the SIB message may only contain the first 20 to 40 msec of the message if the window length is >= 40 msec. [#3519.]
RF board enumeration may fail on rare occasion. This is indicated by the amber color of the Power LED. This is corrected by recycling power. [#3271]
Scanner RF firmware may get corrupted during the firmware download. This problem corrects itself upon retry. [#3315].
Scanner Power/Timing firmware info may return all zeros in Extended Inquiry after firmware download. This problem corrects itself upon retry. [#3385].
PROBLEMS RESOLVED IN THIS RELEASE
MX scanner reports Ec/Io = 0 dB in Top N WCDMA measurement. [#3599]
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 12 of 47
2.2 Release 2.6.1.0 (October 24, 2012)
The release consists of the following components:
Component Name Filename Version
SW Release 2.6.1.0
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.10
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev K
SeeGull Master API SeeGullMaster.dll 1.4.0.1
SeeGull API Reference SeeGull API Reference.chm 1.4
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
TD-LTE 0001 000Bh TD-LTE Support 0005 000Bh TD-LTE MIB/SIB Decoding 000B 000Bh TD-LTE Blind Scanning 000C 000Bh 002C 000Bh
TD-LTE Enhanced Signal Scanning TD-LTE Enhance Signal 2Rx Scanning
000D 000Bh
TD-LTE Power Analyzer
LTE 0001 000Ah FD-LTE Support 0005 000Ah 000B 000Ah
FD-LTE MIB/SIB Decoding FD-LTE Blind Scanning
000C 000Ah 002C 000Ah
FD-LTE Enhanced Signal Scanning FD-LTE Enhanced LTE Signal 2Rx Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h 0005 0001h
GSM C/I Scanning GSM Normal BCCH
000B 0001h 000D 0001h
GSM Blind Scanning GSM Clarify Scanning
WCDMA
0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 13 of 47
0005 0004h 3GPP WCDMA BCH Decoding 0008 0004h 3GPP WCDMA Extended Dynamic Range 000B 0004h 000D 0004h
3GPP WCDMA Blind Scanning 3GPP WCDMA Clarify Pilot Scanning
CDMA
0001 0003h IS-95 Support 0003 0003h IS-95 Pilot Scanning 0008 0003h 000B 0003h
IS-95 Extended Dynamic Range IS-95 Blind Scanning
0001 0005h IS-2000 Support 0003 0005h IS-2000 Pilot Scanning 0008 0005h 000B 0005h
IS-2000 Extended Dynamic Range IS-2000 Blind Scanning
EVDO
0001 0006h IS-856 Support 0003 0006h IS-856 Pilot Scanning 0008 0006h 000B 0006h
IS-856 Extended Dynamic Range IS-856 Blind Scanning
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
NEW FEATURES
LTE FDD 2x2 MIMO measurements.
TD-LTE 2x2 MIMO measurements.
Clarify GSM measurements on up to 150 Channels
Increased Clarify WCDMA Pilot measurements to 24 pilots
Increased the number of channels scanned to 24 for Top N type measurement for WCDMA, CDMA and EV-DO.
WCDMA Top N L3 scanning includes Eps/Io, Ess/Io, Ec and aggregate Ec/Io data modes
Blind scan measurement for CDMA and EVDO Technology.
FD-LTE L3 measurement reporting MIB/SIBs.
RF-path and sub-band measurement data modes for TD/FD LTE L3.
Support for the upper part of E-UTRA band 41 2.5-2.6 TDD (2574-2690MHz) and E-UTRA Band 26 UL Upper Ext 850 (814-849MHz)
Support for WCDMA VI, IX, XIX, XXI and 1500 (PDC) Band Channelization
Supports WCDMA channelization for Extended PCS band
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 14 of 47
Messages Supported
Scanning Messages o Enhanced Power Scan
o RSSI Scan
o GSM Color Code Scan including BCCH
o GSM Clarify Scan
o LTE Enhanced Top N Signal Scan
o CDMA Top N Pilot Scan
o EVDO Top N Pilot Scan
o WCDMA Top N Pilot Scan including BCH
o WCDMA Clarify Pilot Scan
o TD-LTE Power Analyzer Scan
o LTE/WCDMA/GSM/CDMA/EVDO Blind Scan
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o GPS Information
o Inquiry
o Operation Mode
o Product Information
o Reset Device
o Stop Scan
NOTES The GPS LED turns purple if the GPS module is not trained. The GPS may retrain itself
after software upgrades from very early software versions on the MX. Training requires 20 minutes.
The bootup time for the MX scanner is approximately 90 sec.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 15 of 47
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
For TD-LTE, the SIB message may only contain the first 20 to 40 msec of the message if the window length is >= 40 msec. [#3519.]
RF board enumeration may fail on rare occasion. This is indicated by the amber color of the Power LED. This is corrected by recycling power. [#3271]
Scanner RF firmware may get corrupted during the firmware download. This problem corrects itself upon retry. [#3315].
Scanner Power/Timing firmware info may return all zeros in Extended Inquiry after firmware download. This problem corrects itself upon retry. [#3385].
PROBLEMS RESOLVED IN THIS RELEASE
For TD-LTE the DWPTS and UL/DL Configuration measurement result is zero. [#3581] When Blind scan runs with See Hawk with multiple bands and multiple technologies, the
scanner indicates DEVICE ERROR. [#3590] LTE blind scan fails to decode the LTE channels [#3555, #3558] MX TD-LTE detects fewer pilots than EX TD-LTE during drive test. [#3547]. WCDMA Top N Pilot scan may report incorrect PSCH and SSCH Ec/Io in the first several
responses after the scan start. [#3351].
LTE eTopN Signal Scan Reference Signal levels may fluctuate up to 8dB during drive testing. [#3363].
Randomly Reference Signal CINR of 40dB may be reported in LTE eTopN Signal Scan. [#3371].
Blind scan for WCDMA may rarely crash. [#3473].
MX CDMA TopN scan crashes in the case of scan with 18 channels and WCDMA Blind scan. [#3485]
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 16 of 47
2.3 Release 2.4.0.0 (June 8, 2012)
Component Name Filename Version
SW Release 2.4.0. 0
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.7
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev K
SeeGull Master API SeeGullMaster.dll 1.3.0.0
SeeGull API Reference SeeGull API Reference.chm 1.3
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
6T Configuration
Option Code in Hex Description
TD-LTE 0001 000Bh TD-LTE Support 0005 000Bh TD-LTE MIB/SIB Decoding 000B 000Bh TD-LTE Blind Scanning 000C 000Bh TD-LTE Enhanced Signal Scanning 000D 000Bh TD-LTE Power Analyzer LTE
0001 000Ah LTE Support 000B 000Ah LTE Blind Scanning 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h 0005 0001h
GSM C/I Scanning GSM Normal BCCH
000B 0001h GSM Blind Scanning WCDMA
0001 0004h 3GPP WCDMA 0003 0004h 0005 0004h
3GPP WCDMA Pilot Scanning 3GPP WCDMA BCH Decoding
0008 0004h 3GPP WCDMA Extended Dynamic Range 000B 0004h 3GPP WCDMA Blind Scanning
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 17 of 47
CDMA
0001 0003h IS-95 Support 0003 0003h IS-95 Pilot Scanning 0008 0003h IS-95 Extended Dynamic Range 0001 0005h IS-2000 Support 0003 0005h IS-2000 Pilot Scanning 0008 0005h IS-2000 Extended Dynamic Range
EVDO 0001 0006h IS-856 Support 0003 0006h IS-856 Pilot Scanning 0008 0006h IS-856 Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
NEW FEATURES
The MX now supports measurement on six wireless technologies simultaneously including FD-LTE, TD-LTE, WCDMA, GSM, CDMA and EVDO.
TD-LTE support of E-UTRA bands 38, 39, 40 and the lower half of band 41. FD-LTE support of E-UTRA band 9 DL (1700 Japan), E-UTRA band 25 DL/UL (extended PCS aka 1990), E-UTRA band 26 DL (Upper Ext 850) and E-UTRA band 27 DL/UL (Lower Ext 850). CDMA/EVDO Band Class 10 A/B/C/D and Band Class 14 (Lower Ext 850 and Ext PCS respectively)
eTOP N scanning support for TD-LTE technology up to 20 MHz channel bandwidth.
Detection for MIB, and SIB1 through SIB13
Supports up to 16 cell IDs in MIB/SIB mode.
Power Analysis scanning support of TD-LTE technology up to 20 MHz channel bandwidth.
Measurements supported: Resource Blocks, Time Slot, Sub Frame and Frame Analysis.
Blind Scan support of FD-LTE, TD-LTE, WCDMA and GSM protocols.
There is one band per request for each protocol. Channel number or frequencies are reported.
LTE (FD or TD): Supports up to 16 Cell IDs reported per channel with Reference Signal Wideband being the default datamode. The channel bandwidth is selectable by the user.
WCDMA: Supports up to 32 Pilots reported per channel with up to three datamodes: Ec/Io (default), SIR or Time Offset.
GSM: Supports 1 Cell ID (color code) reported per channel with user option for C/I datamode.
Support for MIMO capable ports in hardware.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 18 of 47
GSM Layer 3 BCCH decoding support with a selectable dwelling time.
WCDMA Layer 3 BCH decoding support with a selectable dwelling time.
Immediate Scanning support of EPS, RSSI, GSM Color Code, LTE Enhanced Top N Signal and CDMA/EVDO/WCDMA Top N Pilot.
Messages Supported
Scanning Messages o Enhanced Power Scan
o RSSI Scan
o GSM Color Code Scan (including BCCH)
o LTE Enhanced Top N Signal Scan
o CDMA Top N Pilot Scan
o EVDO Top N Pilot Scan
o WCDMA Top N Pilot Scan (including BCH Layer 3)
o TD-LTE Power Analyzer Scan
o LTE/WCDMA/GSM Blind Scan
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o GPS Information
o Inquiry
o Operation Mode
o Product Information
o Reset Device
o Stop Scan
NOTICE
The GPS LED turns purple if the GPS module is not trained. The GPS may retrain itself after software upgrades from very early software versions on the MX. Training requires 20 minutes.
The bootup time for the MX scanner is approximately 90 sec.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 19 of 47
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
For TD-LTE Layer 3, MBSRN subframes for SIBs 3 -13 are not supported. This is only applicable to extended CP frames. [#3520.]
For TD-LTE, the SIB message may only contain the first 20 to 40 msec of the message if the window length is >= 40 msec. [#3519.]
RF board enumeration may fail on rare occasion. This is indicated by the amber color of the Power LED. This is corrected by recycling power. [#3271, #3327].
Scanner RF firmware may get corrupted during the firmware download. This problem corrects itself upon retry. [#3315].
WCDMA Top N Pilot scan may report incorrect PSCH and SSCH Ec/Io in the first several responses after the scan start. [#3351].
LTE eTopN Signal Scan Reference Signal levels may fluctuate up to 8dB during drive testing. [#3363].
Randomly Reference Signal CINR of 40dB may be reported in LTE eTopN Signal Scan. [#3371].
Scanner Power/Timing firmware info may return all zeros in Extended Inquiry after firmware download. [#3385]. This problem corrects itself upon retry.
Blind scan for WCDMA may rarely crash. [#3473].
MX CDMA TopN scan crashes in the case of scan with 18 channels and WCDMA Blind scan. [#3485]
A high frequency of starting and stopping of multiple scans may cause loss of USB communication. This problem corrects itself by recycling power. [#3395].
LTE eTopN Signal Scan Reference Signal levels may fluctuate up to 8dB during drive testing. [#3363].
Randomly Reference Signal CINR of 40dB may be reported in LTE eTopN Signal Scan. [#3371].
PROBLEMS RESOLVED IN THIS RELEASE
The acquisition of signal transmitted on antenna port 1 is not supported creating an antenna imbalance situation. [#3503].
WCDMA Top N Pilot scan may report incorrect PSCH and SSCH Ec/Io in the first several responses after the scan start. [#3351].
When running multi-technology/multi-band scans the ones that run on the same band may stop responding. [#3381].
The number of FD-LTE antennas is not reported correctly. [#3541]
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 20 of 47
2.4 Release 2.1.0.1 (July 25, 2011)
The release consists of the following components:
Component Name Filename Version
SW Release 2.1.0.1
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.3
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev G
SeeGull Master API SeeGullMaster.dll 1.1.1.0 SeeGull API Reference SeeGull API Reference.chm 1.1
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h GSM C/I Scanning
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning 0008 0004h 3GPP WCDMA Extended Dynamic Range
CDMA 0001 0003h IS-95 Support 0003 0003h IS-95 Pilot Scanning 0008 0003h IS-95 Extended Dynamic Range 0001 0005h IS-2000 Support 0003 0005h IS-2000 Pilot Scanning 0008 0005h IS-2000 Extended Dynamic Range
EVDO 0001 0006h IS-856 Support 0003 0006h IS-856 Pilot Scanning 0008 0006h IS-856 Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 21 of 47
0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
The release details and history are provided in the following sections.
NEW FEATURES
The SeeGull MX can now perform LTE eTop N scans based on frequency instead of only channel number.
Messages Supported
Scanning Messages o Enhanced Power Scan
o RSSI Scan
o GSM Color Code Scan
o LTE Enhanced Top N Signal Scan
o CDMA Top N Pilot Scan
o EVDO Top N Pilot Scan
o WCDMA Top N Pilot Scan
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o GPS Information
o Inquiry
o Operation Mode
o Product Information
o Reset Device
o Stop Scan
NOTICE
The GPS LED turns purple if the GPS module is not trained. The GPS may retrain itself after software upgrades from very early software versions on the MX. Training can take up to 20 minutes
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 22 of 47
RF board enumeration may fail on rare occasion. This is indicated by the amber color of the Power LED. This is corrected by recycling power. [#3271].
Scanner RF firmware may get corrupted during the firmware download. This problem corrects itself upon retry. [#3315].
WCDMA Top N Pilot scan may report incorrect PSCH and SSCH Ec/Io in the first several responses after the scan start. [#3351].
LTE eTopN Signal Scan Reference Signal levels may fluctuate up to 8dB during drive testing. [#3363].
Randomly Reference Signal CINR of 40dB may be reported in LTE eTopN Signal Scan. [#3371].
PROBLEMS RESOLVED IN THIS RELEASE
Running multi-technology scans on the same band may cause that band to stop responding. [#3381].
Power scans (RSSI, EPS or Spectrum Analysis) may stop responding after frequent restarting of all scan types. [#3393]
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 23 of 47
2.5 Release 2.1.0.0 (June 28, 2011)
The release consists of the following components:
Component Name Filename Version
SW Release 2.1.0.0
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.3
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev G
SeeGull Master API SeeGullMaster.dll 1.1.1.0 SeeGull API Reference SeeGull API Reference.chm 1.1
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h GSM C/I Scanning
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning 0008 0004h 3GPP WCDMA Extended Dynamic Range
CDMA 0001 0003h IS-95 Support 0003 0003h IS-95 Pilot Scanning 0008 0003h IS-95 Extended Dynamic Range 0001 0005h IS-2000 Support 0003 0005h IS-2000 Pilot Scanning 0008 0005h IS-2000 Extended Dynamic Range
EVDO 0001 0006h IS-856 Support 0003 0006h IS-856 Pilot Scanning 0008 0006h IS-856 Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 24 of 47
0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
The release details and history are provided in the following sections.
NEW FEATURES
Five technologies LTE, WCDMA, GSM, CDMA and EVDO operate simultaneously.
Boot up time has been decreased from 120 seconds to 90 seconds.
Reset Request resets the unit instead of shutting down the unit.
The inquiry status indicates “Fail” if there is an error during scanner boot-up.
Fan speed is controlled for indoor mode.
Messages Supported
Scanning Messages o Enhanced Power Scan
o RSSI Scan
o GSM Color Code Scan
o LTE Enhanced Top N Signal Scan
o CDMA Top N Pilot Scan
o EVDO Top N Pilot Scan
o WCDMA Top N Pilot Scan
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o GPS Information
o Inquiry
o Operation Mode
o Product Information
o Reset Device
o Stop Scan
NOTICE
The GPS LED turns purple if the GPS module is not trained. The GPS may retrain itself after software upgrades from very early software versions on the MX.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 25 of 47
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
Running multi-technology scans on the same band may cause that band to stop responding. [#3381].
RF board enumeration may fail on rare occasion. This is indicated by the amber color of the Power LED. This is corrected by recycling power. [#3271].
Scanner RF firmware may get corrupted during the firmware download. This problem corrects itself upon retry. [#3315].
WCDMA Top N Pilot scan may report incorrect PSCH and SSCH Ec/Io in the first several responses after the scan start. [#3351].
LTE eTopN Signal Scan Reference Signal levels may fluctuate up to 8dB during drive testing. [#3363].
Randomly Reference Signal CINR of 40dB may be reported in LTE eTopN Signal Scan. [#3371].
PROBLEMS RESOLVED IN THIS RELEASE
When running all five technologies there could be conflict in measurements between LTE/WCDM/GSM and LTE/CDMA/EVDO. [#3316, #3317].
WCDMA and GSM scans may freeze on very rare occasions during multi-technology measurements. [#3318]
CDMA or EVDO Top N Pilot scan Pilot Delay negative values are reported as very large positive numbers. [#3358].
Stop scan may fail occasionally for TopN Pilot scan. [#3376]
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 26 of 47
2.6 Release 2.0.0.2 (June 17, 2011)
The release consists of the following components:
Component Name Filename Version
SW Release 2.0.0.2
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.2
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev F
SeeGull Master API SeeGullMaster.dll 1.1.0.3 SeeGull API Reference SeeGull API Reference.chm 1.1
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Configuration 1
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h GSM C/I Scanning
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning 0008 0004h 3GPP WCDMA Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 27 of 47
Configuration 2
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
CDMA 0001 0003h IS-95 Support 0003 0003h IS-95 Pilot Scanning 0008 0003h IS-95 Extended Dynamic Range 0001 0005h IS-2000 Support 0003 0005h IS-2000 Pilot Scanning 0008 0005h IS-2000 Extended Dynamic Range
EVDO 0001 0006h IS-856 Support 0003 0006h IS-856 Pilot Scanning 0008 0006h IS-856 Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
The release details and history are provided in the following sections.
NEW FEATURES None
Messages Supported
Scanning Messages o Enhanced Power Scan
o RSSI Scan
o GSM Color Code Scan
o LTE Enhanced Top N Signal Scan
o CDMA Top N Pilot Scan
o EVDO Top N Pilot Scan
o WCDMA Top N Pilot Scan
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o GPS Information
o Inquiry
o Operation Mode
o Product Information
o Reset Device
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 28 of 47
o Stop Scan
NOTICE
When running all five technologies there could be conflict in measurements between LTE/WCDM/GSM and LTE/CDMA/EVDO [#3316, #3317].
CDMA Code Domain Scan is not supported [#3353]
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
Scanner RF firmware may get corrupted during the firmware download. This problem corrects itself upon retry. [#3315]
WCDMA and GSM scans may freeze on very rare occasions during multi-technology measurements. [#3318]
WCDMA Top N Pilot scan may report incorrect PSCH and SSCH Ec/Io in the first several responses after the scan start [#3351]
CDMA or EVDO Top N Pilot scan Pilot Delay negative values are reported as very large positive numbers [#3358]
PROBLEMS RESOLVED IN THIS RELEASE
LTE US 700 C UL (EUTRA-13) Band tuning coefficients are incorrect [#3367]
2.7 Release 2.0.0.1 (June 10, 2011)
The release consists of the following components:
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 29 of 47
Component Name Filename Version
SW Release 2.0.0.1
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.2
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev F
SeeGull Master API SeeGullMaster.dll 1.1.0.3 SeeGull API Reference SeeGull API Reference.chm 1.1
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Configuration 1
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h GSM C/I Scanning
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning 0008 0004h 3GPP WCDMA Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 30 of 47
Configuration 2
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
CDMA 0001 0003h IS-95 Support 0003 0003h IS-95 Pilot Scanning 0008 0003h IS-95 Extended Dynamic Range 0001 0005h IS-2000 Support 0003 0005h IS-2000 Pilot Scanning 0008 0005h IS-2000 Extended Dynamic Range
EVDO 0001 0006h IS-856 Support 0003 0006h IS-856 Pilot Scanning 0008 0006h IS-856 Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
The release details and history are provided in the following sections.
NEW FEATURES
Indoor Test Mode
CDMA/EVDO Top N Pilot and RSSI Scanning
Messages Supported
Scanning Messages o Enhanced Power Scan
o RSSI Scan
o GSM Color Code Scan
o LTE Enhanced Top N Signal Scan
o CDMA Top N Pilot Scan
o EVDO Top N Pilot Scan
o WCDMA Top N Pilot Scan
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o GPS Information
o Inquiry
o Operation Mode
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 31 of 47
o Product Information
o Reset Device
o Stop Scan
NOTICE
When running all five technologies there could be conflict in measurements between LTE/WCDM/GSM and LTE/CDMA/EVDO [#3316, #3317].
CDMA Code Domain Scan is not supported in this release [#3353]
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
Scanner RF firmware may get corrupted during the firmware download. This problem corrects itself upon retry. [#3315]
WCDMA and GSM scans may freeze on very rare occasions during multi-technology measurements. [#3318]
WCDMA Top N Pilot scan may report incorrect PSCH and SSCH Ec/Io in the first several responses after the scan start [#3351]
CDMA or EVDO Top N Pilot scan Pilot Delay negative values are reported as very large positive numbers [#3358]
PROBLEMS RESOLVED IN THIS RELEASE
LTE European 800 UL/DL (EUTRA-20) Band Measurement Bandwidth Codes in Channelization Table are incorrect[#3372]
USB LED does not illuminate [#3186]
Correct CDMA or EVDO pilot number is not reported if lock to GPS signal is not available from the power up. [#3328]
EVDO Top N Pilot scanning detection rate may drop when running concurrently with CDMA Top N Pilot [#3345]
When running multiple channels Incorrect overall Message Status “NoPilotAvailable” is reported in WCDMA TopN Pilot if pilots are not detected on the first channel in the channel list [#3346]
EVDO Top N Pilot Ec/Io level may periodically drop up to 4dB at approximately ten minute intervals.[#3347]
GPS Information Message may report nonzero velocity even when the scanner is static [#3349]
EVDO Top N Pilot scan speed drops when more than 16 RF channels requested.
Lowered EVDO TopN Pilot Ec/Io sensitivity to carrier frequency offset [#3355]
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 32 of 47
2.8 Release 1.1.1.1 (May 16, 2011)
The release consists of the following components:
Component Name Filename Version
SW Release 1.1.1.1
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.1
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev F
SeeGull Master API SeeGullMaster.dll 1.1.0.3 SeeGull API Reference SeeGull API Reference.chm 1.1
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h GSM C/I Scanning
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning 0008 0004h 3GPP WCDMA Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
The release details and history are provided in the following sections.
NEW FEATURES
LTE Bands: E-UTRA UL/DL 11, 18-21, 24 and UL 13
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 33 of 47
Messages Supported
Scanning Messages
o Enhanced Power Scan
o RSSI Scan
o GSM Color Code Scan
o LTE Enhanced Top N Signal Scan
o WCDMA Top N Pilot Scan
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o GPS Information
o Inquiry
o Operation Mode
o Product Information
o Reset Device
o Stop Scan
NOTICE The power switch must remain in the Drive Test position at all times. The Indoor Test
Mode is not available at this time.
USB LED does not illuminate [#3186].
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
Scanner RF firmware may get corrupted during the firmware download. This problem corrects itself upon retry. [#3315]
WCDMA and/or GSM scans may freeze on very rare occasions during multi-technology measurements. [#3318]
PROBLEMS RESOLVED IN THIS RELEASE
None
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 34 of 47
2.9 Release 1.1.1.0 (May 02, 2011)
The release consists of the following components:
Component Name Filename Version
SW Release 1.1.1.0
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.1
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev F
SeeGull Master API SeeGullMaster.dll 1.1.0.3 SeeGull API Reference SeeGull API Reference.chm 1.1
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h GSM C/I Scanning
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning 0008 0004h 3GPP WCDMA Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
The release details and history are provided in the following sections.
NEW FEATURES
International LTE Bands
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 35 of 47
Scan Sampling for RSSI, Enhanced Power Scan, Color Code, Top N Pilot and Enhanced Top N Signal Scan
o Average, Standard Deviation, Min and Max
Enhanced Power Scan
o Spectrum Analyzer operational mode with sweeping: 1, 2, 4, 8 or 16 times
LTE Enhanced Top N Signal Scan
o Channel Style: 5 or 6
Messages Supported
Scanning Messages o Enhanced Power Scan
o RSSI Scan
o GSM Color Code Scan
o LTE Enhanced Top N Signal Scan
o WCDMA Top N Pilot Scan
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o GPS Information
o Inquiry
o Operation Mode
o Product Information
o Reset Device
o Stop Scan
NOTICE The power switch must remain in the Drive Test position at all times. The Indoor Test
Mode is not available at this time.
USB LED does not illuminate [#3186].
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
Scanner RF firmware may get corrupted during the firmware download. This problem corrects itself upon retry. [#3315]
WCDMA and/or GSM scans may freeze on very rare occasions during multi-technology measurements. [#3318]
PROBLEMS RESOLVED IN THIS RELEASE
Top N Pilot High Speed Mode is rejected with Response Message Status Parameter “Out of Range”.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 36 of 47
2.10 Release 1.3 (April 11, 2011)
The release consists of the following components:
Component Name Filename Version
SW Release 1.0.1.5
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.1
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev F
SeeGull Master API SeeGullMaster.dll 1.1.0.1 SeeGull API Reference SeeGull API Reference.chm 1.0
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h GSM C/I Scanning
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning 0008 0004h 3GPP WCDMA Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
The release details and history are provided in the following sections.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 37 of 47
NEW FEATURES
International LTE Bands
Scan Sampling for RSSI, Enhanced Power Scan, Color Code, Top N Pilot and Enhanced Top N Signal Scan
o Average, Standard Deviation, Min and Max
Enhanced Power Scan
o Spectrum Analyzer operational mode with sweeping: 1, 2, 4, 8 or 16 times
LTE Enhanced Top N Signal Scan
o Channel Style: 5 or 6
FEATURES
International LTE Bands
GPS Message
Scan Sampling for RSSI, Enhanced Power Scan, Color Code, Top N Pilot and Enhanced Top N Signal Scan
o Average, Standard Deviation, Min and Max
Enhanced Power Scan
o Scan mode: 0-Auto
o Supported with Frequency List, frequency must be within valid frequency range for requested band
o Spectrum Analyzer operational mode with sweeping: 1, 2, 4, 8 or 16 times
o Message Time Stamp
RSSI Scan
o Scan mode: 0-Auto
o Same Channel Style with contiguous Channel List, channel must be within valid channel range for requested band
o Message Time Stamp
GSM Color Code Scan
o Scan mode: 0-Auto
o Message Time Stamp
LTE Enhanced Top N Signal Scan
o Scan mode: 0-Auto
o Channel Style: 0, 2, 3, 4, 5 or 6
o Sync Signal Measurement Mode:
o Reference Signal Measurement Mode:
WCDMA Top N Pilot Scan
o Scan Mode: 0-Auto
o Pilot Mode: High Dynamic
o Message Time Stamp
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 38 of 47
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o Product Information
o Operation Mode
o Reset Device
WARNING
Fan speed has been increased to support operation over the full ambient temperature range.
Boot up in progress is indicated by an orange status LED. Successful boot up is indicated by a green status LED.
The power switch must remain in the Drive Test position at all times. The Indoor Test Mode is not available at this time.
USB LED does not illuminate [#3186].
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
None
PROBLEMS RESOLVED IN THIS RELEASE
Unit may (rarely) not successfully boot up and the system LED remains orange. If this event occurs, power cycle the unit. [#2994]
USB communication from scanner to host freezes when multi-scans with multi-protocol are requested. [#3223]
GPS timestamp is random number, different from one band to another, and jumping around if unit is not connected to GPS at power up and remains GPS un-locked. [#3247]
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 39 of 47
2.11 Release 1.2 (February 8, 2011)
The release consists of the following components:
Component Name Filename Version
SW Release 1.0.0.2
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.0
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev E
SeeGull Master API SeeGullMaster.dll 1.0.1.3 SeeGull API Reference SeeGull API Reference.chm 1.0
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h GSM C/I Scanning
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning 0008 0004h 3GPP WCDMA Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
The release details and history are provided in the following sections.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 40 of 47
FEATURES
GPS Message
Enhanced Power Scan
o Scan mode: 0-Auto
o Supported with Frequency List, frequency must be within valid frequency range for requested band
o Spectrum Analyzer operational mode
o Message Time Stamp
RSSI Scan
o Scan mode: 0-Auto
o Same Channel Style with contiguous Channel List, channel must be within valid channel range for requested band
o Message Time Stamp
GSM Color Code Scan
o Scan mode: 0-Auto
o Message Time Stamp
LTE Enhanced Top N Signal Scan
o Scan mode: 0-Auto
o Channel Style: 0, 2, 3 or 4
o Sync Signal Measurement Mode:
o Reference Signal Measurement Mode:
WCDMA Top N Pilot Scan
o Scan Mode: 0-Auto
o Pilot Mode: High Dynamic
o Message Time Stamp
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o Product Information
o Operation Mode
o Reset Device
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 41 of 47
WARNING
Fan speed has been increased to support operation over the full ambient temperature range.
Boot up in progress is indicated by an orange status LED. Successful boot up is indicated by a green status LED.
Unit may (rarely) not successfully boot up and the orange LED remains orange. If this event occurs, power cycle the unit [#2994].
The power switch must remain in the Drive Test position at all times. The Indoor Test Mode is not available at this time.
USB LED does not illuminate [#3186].
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
None
PROBLEMS RESOLVED IN THIS RELEASE
Color Code scan may report invalid measurement on adjacent channel[#3184]
Color Code measurements of extremely high or low power signals of > -30 dBm or < -95 dBm may be inaccurate. [#3161]
Some instabilities may occur under multiple scanning scenarios[#3205], [#3198],
OTHER CHANGES IN THIS RELEASE
Scanner boot up success rate improved [#2994]
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 42 of 47
2.12 Release 1.1 (January 21, 2011)
The release consists of the following components:
Component Name Filename Version
SW Release 1.0.0.1
SeeGull MX Product Reference SeeGull MX Product Reference.chm 1.0.0.0
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev E
SeeGull Master API SeeGullMaster.dll 1.0.1.3 SeeGull API Reference SeeGull API Reference.chm 1.0
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h GSM C/I Scanning
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning 0008 0004h 3GPP WCDMA Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
The release details and history are provided in the following sections.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 43 of 47
FEATURES
GPS Message
Enhanced Power Scan
o Scan mode: 0-Auto
o Supported with Frequency List, frequency must be within valid frequency range for requested band
o Spectrum Analyzer operational mode
o Message Time Stamp
RSSI Scan
o Scan mode: 0-Auto
o Same Channel Style with contiguous Channel List, channel must be within valid channel range for requested band
o Message Time Stamp
GSM Color Code Scan
o Scan mode: 0-Auto
o Message Time Stamp
LTE Enhanced Top N Signal Scan
o Scan mode: 0-Auto
o Channel Style: 0, 2, 3 or 4
o Sync Signal Measurement Mode:
o Reference Signal Measurement Mode:
WCDMA Top N Pilot Scan
o Scan Mode: 0-Auto
o Pilot Mode: High Dynamic
o Message Time Stamp
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o Product Information
o Operation Mode
o Reset Device
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 44 of 47
WARNING The power draw of the MX unit is expected to be 6A @ 12V.
Boot up in progress is indicated by an orange status LED. Successful boot up is indicated by a green status LED.
Unit may (rarely) not successfully boot up and the orange LED remains orange. If this event occurs, power cycle the unit.
The power switch must remain in the Drive Test position at all times. The Indoor Test Mode is not available at this time.
USB LED does not illuminate [#3186].
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
Color Code scan may report invalid measurement on adjacent channel[#3184[
Color Code measurements of extremely high or low power signals of > -30 dBm or < -95 dBm may be inaccurate. [#3161]
Some instabilities may occur under multiple scanning scenarios[#3205], [#3198],
PROBLEMS RESOLVED IN THIS RELEASE
Conducting concurrent measurements of multiple technologies may result in rare, sporadic variations in Top N and eTop N data, as well as in Color Code power measurements on some channels in a lab environment. [#3175], [#3162], [#3158]
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 45 of 47
2.13 Release 1.0 (January 14, 2011)
The release consists of the following components:
Component Name Filename Version
SW Release 1.0.0.0
SeeGull MX Product Reference SeeGull MX Product Reference.chm 0.0.1.0
SeeGull Master API Release Notes SeeGull Master API Release Notes.pdf 14RN57-00M Rev E
SeeGull Master API SeeGullMaster.dll 1.0.1.2 SeeGull API Reference SeeGull API Reference.chm 1.0
SeeGull MX Driver Release Notes SeeGull MX Driver Release Notes Rev B.pdf
14RN59-00M Rev B
SeeGull MX Driver MX WinUSB Drive Package 1.0
SeeGull MX Driver Installation Procedure
SeeGull MX Driver Installation Procedure.pdf
100059-00 Rev B
SUPPORTED OPTIONS
Option Code in Hex Description
LTE 0001 000Ah LTE Support 000C 000Ah LTE Enhanced Signal Scanning
GSM 0001 0001h GSM Support 0002 0001h GSM BSIC (Color Code) Decoding 0004 0001h GSM C/I Scanning
WCDMA 0001 0004h 3GPP WCDMA 0003 0004h 3GPP WCDMA Pilot Scanning 0008 0004h 3GPP WCDMA Extended Dynamic Range
Misc. 0001 0000h GPS Navigation 0003 0000h Spectrum Analyzer 0005 0000h Absolute Time Stamp 0006 0000h Enhanced Power Scanning
The release details and history are provided in the following sections.
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 46 of 47
FEATURES
GPS Message
Enhanced Power Scan
o Scan mode: 0-Auto
o Supported with Frequency List, frequency must be within valid frequency range for requested band
o Spectrum Analyzer operational mode
o Message Time Stamp
RSSI Scan
o Scan mode: 0-Auto
o Same Channel Style with contiguous Channel List, channel must be within valid channel range for requested band
o Message Time Stamp
GSM Color Code Scan
o Scan mode: 0-Auto
o Message Time Stamp
LTE Enhanced Top N Signal Scan
o Scan mode: 0-Auto
o Channel Style: 0, 2, 3 or 4
o Sync Signal Measurement Mode:
o Reference Signal Measurement Mode:
WCDMA Top N Pilot Scan
o Scan Mode: 0-Auto
o Pilot Mode: High Dynamic
o Message Time Stamp
General Purpose Messages
o Channel to Frequency Conversion
o Diagnostic Information
o Product Information
o Operation Mode
SeeGull® MX Product Release Notes
Rev. X PCTEL, INC. PROPRIETARY INFORMATION Page 47 of 47
WARNING The power draw of the MX unit is expected to be 6A @ 12V.
Boot up in progress is indicated by an orange status LED. Successful boot up is indicated by a green status LED.
Unit may (rarely) not successfully boot up and the orange LED remains orange. If this event occurs, power cycle the unit.
The power switch must remain in the Drive Test position at all times. The Indoor Test Mode is not available at this time.
USB LED does not illuminate.
KNOWN PROBLEMS IDENTIFIED IN THIS RELEASE
Conducting concurrent measurements of multiple technologies may result in rare, sporadic variations in Top N and eTop N data, as well as in Color Code power measurements on some channels in a lab environment. [#3175], [#3162], [#3158]
Color Code measurements of extremely high or low power signals of > -30 dBm or < -95 dBm may be inaccurate. [#3161]
PROBLEMS RESOLVED IN THIS RELEASE
Top N Pilot scan speed is limited to 20ms per channel at this time [#2971]
New scan requests may not run after some use of the Stop Scan message. If this event occurred power cycle the unit [#2984]
Concurrent scanning requests may periodically have sequential responses [#3022]
Color Code scan is slower at high input RF power levels [#3052]
With concurrent scanning of RSSI, Enhanced Top N Signal, Top N Pilot and Color Code on four different bands, Color Code sometimes may not respond.[#3056]
All LTE technology specific scans such as Enhanced Top N Signal, RSSI, Spectrum Analyzer, Enhanced Power Scan may report power level drop if running with Spectrum Analyzer on another band.[#3065]
GPS Responses are not returned in case GPS is not locked.[#3089]
MX will not be scanning after issuing an “Already In Use” message. If this event occurs, power cycle the unit. [#3049]
Per Operation Mode Message request device responds with Error Status 8- “Unsupported request”[#2980]