seed rate charts - great plains · great plains mfg., inc. 2 401-347b 08/02/2010 setting planting...

© Copyright 2010 Printed 08/02/2010 401-347B

Manufacturing, Inc.www.greatplainsmfg.com

Seed Rate Charts for theYP1225 or YP1625 PlantersFor Yield-Pro® 1225 s/n A1056K to A1110KFor Yield-Pro® 1625 s/n A1104B to A1189BThe following pages are to assist in the proper setting of seeding and fertil-izer rates for the YP1225 or YP1625 30 and 40ft Yield-Pro®Planters.To assure the most accurate seeding rates it is recommended that theplanter and meters be calibrated for the desired seed at the time of planting.

http://www.greatplainsmfg.com

Great Plains Mfg., Inc.

401-347B 08/02/2010

Table of Contents

© Copyright 2006, 2007, 2008, 2009, 2010. All rights Reserved

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the prepa-ration of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use ofthe information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes the state of thisproduct at the time of its publication, and may not reflect the product in the future.

Great Plains Manufacturing, Incorporated TrademarksThe following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Introduction ................................................................ 1Models Covered....................................................... 1

Covered YP1225 Models ..................................... 1Covered YP1625 Models ..................................... 1

Document Family ..................................................... 1Setting Planting Rate ............................................... 2Setting Fertilizer Rate .............................................. 2

Setting Planting Rate................................................. 3Hydraulic Drive Meter Rate...................................... 3Ground Drive Meter Rate......................................... 3

System Check ...................................................... 3Drive Speed Range Sprockets............................. 3Transmission Sprockets....................................... 4

Checking Planting Rate ........................................... 5Seed Rate Check Sample Size ........................ 5

Checking Singulated Rate.................................... 5Seed Rate Check Examples ............................ 5

Hydraulic Drive Calibration....................................... 6Speed Calibration............................................... 11Veris Calibration for Finger Meters .................... 13Veris Calibration for Singulating Meters............. 14

Singulating Meter Planting...................................... 16Reading a Singulated Rate Chart .......................... 16

Ground Drive...................................................... 16Cotton, 30in, 120 Cell ............................................ 17Cotton, 36in, 120 Cell ............................................ 18Milo, Low, 102 Cell ............................................... 19Milo, 102 Cell ........................................................ 20Milo, Low, 135 Cell ................................................ 21Milo, 135 Cell ........................................................ 22Milo, 270 Cell ........................................................ 23Soybeans, 100 Cell (1 of 2) .................................. 24Soybeans, 110 Cell (1 of 2) ................................... 26

Finger Meter Planting .............................................. 29Reading a Finger Meter Rate Chart ....................... 29

Hydraulic or Ground Drive.................................. 29Ground Drive...................................................... 29

Finger Meter Adjustments...................................... 30

Finger Meter Brush Adjustment ......................... 30Finger Meter Inserts ....................................... 31

20in Rows, 6 Finger ............................................... 3220in Rows, 12 Finger ............................................. 33Twin Row,30in, 6 Finger, Low Range.................... 34Twin Row 30in, 6 Finger, High Range ................... 35Twin Row 30in, 12 Finger, High Range ................. 3630in Rows, 6 Finger, Low Range........................... 3730in Rows, 12 Finger, Low Range......................... 3830in Rows, 12 Finger, High Range........................ 39Twin Row, 36in, 6 Finger ....................................... 40Twin Row, 36in, 12 Finger ..................................... 4136in Rows, 6 Finger ............................................... 4236in Rows, 12 Finger ............................................. 43

Sprocket Indexing (Stagger)................................... 44Sprocket Indexing Charts....................................... 45

30in Twin Row Sprocket Indexing...................... 4536in Twin Row Sprocket Indexing...................... 46

Indexing Fine Adjustment ...................................... 476-Finger Meter Stagger Adjustment................... 4712-Finger Meter Stagger Adjustment................. 48

Fertilizer Rate ........................................................... 49Orifice Plate Selection............................................ 49Ground Drive Fertilizer Rate .................................. 50

Fertilizer Rate: YP1225-1230, -1820, -24TR ..... 51Fertilizer Rate: YP1225-2315............................. 52Fertilizer Rate: YP1225-16TR36........................ 53Fert. Rate: YP1625-1630, -1670, -2420, 32TR.. 54Fertilizer Rate: YP1625-3115............................. 55Fertilizer Rate: YP1625-1236, -24TR36............. 56

Shaft Drive Fertilizer Rate...................................... 57Shaft Drive Type 1 ................................................. 57Shaft Drive Type 2 ................................................. 58

Setting Relief Valve............................................ 59Strainer .............................................................. 59

Appendix .................................................................. 60Seed Lubricants ..................................................... 60

Great Plains Mfg., Inc.1

Introduction

This manual covers the following tasks for the 30 and 40ftYield-Pro Planter:

• setting and checking seed rate for singulated crops

• setting and checking seed rate for volumetric (“granular”)crops, and;

Models CoveredCovered YP1225 ModelsThis manual applies to YP1225 planters with serial numberA1056K to A1110K.

Covered YP1625 ModelsThis manual applies to YP1625 planters with serial numberA1104B to A1189B.

Document Family

This manual is your guide to planter adjustments forachieving specific seed population targets. It alsoincludes information you may need to properly setupand adjust a separately provisioned fertilizer tank andpump system.

Although some setup/adjustment material herein isrepeated from the Operator’s Manual, you need to bethoroughly familiar with planter operations and adjust-ments before applying this Seed Rate manual and itstable data.

YP1225-1230 30-Foot, 12-Row, 30-Inch

YP1225-16TR36 30-Foot, 16-Row (8 Twin), 36-Inch

YP1225-1820 30-Foot, 18-Row, 20-Inch

YP1225-2315 30-Foot, 23-Row, 15-Inch

YP1225-1230 30-Foot, 12-Row, 30-Inch


YP1225-1820 30-Foot, 18-Row, 20-Inch

YP1225-2315 30-Foot, 23-Row, 15-Inch

YP1225-24TR 30-Foot, 24-Row, (12 Twin) 30-Inch

YP1625-1236 40-Foot, 12-Row, 36-Inch

YP1625-1630 40-Foot, 16-Row, 30-Inch

YP1625-2420 40-Foot, 24-Row, 20-Inch


YP1625-3115 40-Foot, 31-Row, 15-Inch

YP1625-32TR 40-Foot, 32-Row (16 Twin), 30-Inch

401-226M Owner’s Manual

401-347B Seed Rate Charts (this manual)

401-226P Parts Manual

11001-1359 Seed Manager SE Manual

Figure 1YP40 Planter

29162

08/02/2010 401-347B


Setting Planting Rate

There are four to six steps to obtaining the desired num-ber of seeds per acre, some of which apply only toground-drive planters, certain meter types, and particularrow unit configurations:

1. Know the characteristics of the seedConsult your seed supplier’s reference documents.

2. Install the correct seed meters and wheelsConsult your Great Plains dealer and see “SeedMeter Setup and Adjustment” in the Operator’sManual.

3. Adjust Finger Pickup meters for the seedThis only applies to finger pickup meters.See “Finger Meter Adjustments” on page 30.

4. Sprocket index for staggered twin-rowOn twin-row planters, with certain crops, get maxi-mum benefit with precise seed spacing betweenadjacent rows. See “Indexing Fine Adjustment” onpage 47.

5. Set meter rateFor hydraulic meter drive, this is done via the seedmonitor. Once data about your planter is entered,you select the seed rate directly. Consult the manualfor the seed monitor.

For ground drive meters, two sprocket sets are con-figured at each contact wheel:a. rangeb. transmission

See “Ground Drive Meter Rate” on page 3.

6. Check planting rateSee “Checking Planting Rate” on page 5.

Setting Fertilizer Rate

Planters equipped fertilizer systems have one of twotypes of fertilizer pump. Each has its own rate configura-tion.

If you have pumps with their own ground-drive wheels,see “Ground Drive Fertilizer Rate” on page 50.

If you have pumps driven by the meter transfer shafts,see “Shaft Drive Fertilizer Rate” on page 57.

Rates are primarily controlled by the tank pump, but canonly be consistently obtained when using the correct sizeorifices in the manifolds. See “Fertilizer Rate” onpage 49 for orifice information.

Refer to the planter Operator’s manual for details onpump operations.

401-347B 08/02/2010


Setting Planting Rate

Hydraulic Drive Meter RateHydraulic drive meter rate is set directly on the seedmonitor in the tractor. Consult the monitor manual fordetailed instructions, which may vary over time withfirmware updates to the monitor system.

You will need to enter/update your planter configuration(width/row-count, single-row/twin, meter type, wheelcell count, etc.). Once entered, you can specify thedesired population directly in seeds per acre.

Although the sprocket information in the Seed RateCharts of this manual does not apply to hydraulic drive,the recommended planting speed (in mph) does apply.

Note: For most consistent results, and least wear on themeters, check the seed rate chart for the crop ormeter type/seed wheel, and do not exceed therecommended ground speed.

Ground Drive Meter RateSystem CheckBefore setting the planting rate, rotate the contactwheel. Check that seed meters, seed tubes, and drivesare working properly and free from foreign material.

Check that tire pressure is set according to the “Specifi-cations and Capacities” in your Operator’s manual.

Drive Speed Range SprocketsSelect the correct drive speed range sprockets for yourseed from the “Seed Rate Charts,” starting on page 29.

Refer to Figure 2

Loosen idler and remove chain . Remove retainingpins from Driving and Driven shafts and installspeed range sprockets as necessary.

Note: Make sure the correct sprockets have been in-stalled in the DRIVING and DRIVEN locations asshown.

Reroute chain over sprockets and idlers as shown.Move idler into chain so chain has 1⁄4in slack in its long-est span. Tighten idler and install lynch pins.

Figure 2Drive Speed Range

Sprockets Adjustment

21974

1

4

32

DRIVING

DRIVEN

1 2

3 4

08/02/2010 401-347B


Transmission SprocketsRefer to Figure 3

Loosen idlers and remove drive chain . Removelynch pins from Driving and Driven shafts and rear-range driving and driven sprockets as necessary.

Reroute drive chain over sprockets and idlers as shown.Move idlers into chain so chain has 1⁄4in slack in itslongest span. Tighten idlers and install lynch pins.

Figure 3Transmission

Sprockets Adjustment

21974

4

DRIVEN

DRIVING

1

23

1 2

3 4

1

401-347B 08/02/2010


Checking Planting RateAlthough your seed monitor will report useful full passresults, cautious practice includes manually checking theseed rate early in the first pass.

The seed charts are based on cleaned and sized seed.Extreme seed variations, foreign material and tire pres-sure can materially affect planting rate.

Checking the rate also provides a double-check on yourpopulation calculations and drive configuration.

The procedure is different for singulated and volumetricseeding.

Checking Singulated Rate1. Using the table at right, determine the length and

number of rows to check. For twin-row operation, apair of row units counts as one row.

2. Adjust the planting depth to shallow on that numberof rows units. Using center and wing-end row unitsfor measurement provides a more accurate assess-ment of overall planter performance. Pick centerunits outside wheel tracks.

3. Use bungees or wire to tie-up the press wheelassembly on the tested row units, so that the seed isnot covered. Tie up both in a pair for twin-row.

4. Operate the planter for the distance in the table, plusa few feet for the press wheels to clear the end of thesample distance.

5. Count the number of seeds in the test rows.

6. Multiply the total number of seeds counted by 200 ifmeasuring for 1⁄200 acre, or by 1000 if measuring for1⁄1000 acre. This is the plant population in seeds peracre.

7. If the populated is substantially different thanexpected, check tire inflation, and on a ground-driveplanter, double-check the sprocket configuration.See “Troubleshooting” in Operator’s Manual.

Seed Rate Check Examples

Example 1: Single Row

If you have a 10in row spacing planter, according to thechart, three rows must be counted. Measure 17ft 5in andcount the number of seeds in three rows. If the numberis, for example, 180, multiply 180 by 1,000.

180 X 1,000 = 180,000 seeds per acre.

Example 2: Twin Row

If you have a Twin Row 30in spacing planter, accordingto the chart, both rows of the twin row must be counted.Measure 87ft 1in and count the number of seeds in theparallel row. If the number is, for example, 170, multiplyby 200.

170 x 200 = 34,000 seeds per acre

NOTE: Count Twin Row as one row.

Seed Rate Check Sample Size

Note: Use 1/200 acre for populations less than 100,000seeds/acre. Use 1/1,000 acre for populationsabove 100,000 seeds/acre.

Rows to Sample Length of Row toCount for

Spacing Number1⁄1000thAcre

1⁄200thAcre

71⁄2in4 17ft 5in Use 1⁄1000th

Acre

91⁄2in3 18ft 4in Use 1⁄1000th

Acre

10in3 17ft 5in Use 1⁄1000th

Acre

15in 2 17ft 5in 87ft 1in



30in or30in Twin Row

1*

* Twin rows count as one row.

17ft 5in 87ft 1in


1* 14ft 6in 72ft 7in





15in Skip Row 2 15ft 3in 76ft 3in

08/02/2010 401-347B


Hydraulic Drive CalibrationThis section applies only if the planter has hydraulicmeter drive.

Refer to Figure 4

1. Turn on Controller Console by pressing On/VR key.Green light above On/VR key will illuminate whenpower is on. Adjust desired planting rate by using theUp/Down arrow keys to change the Set rate.

2. Set the desired Rate by using the Up/Down arrowkeys.

Refer to Figure 5

3. Press Function key until Calibration Number windowappears.

4. Select drive calibration number based on row spac-ing and metering wheel, from chart. See “Veris Cali-bration for Finger Meters” on page 13 or See“Veris Calibration for Singulating Meters” onpage 14.

5. Use Up/Down arrow keys to set Calibration number.

Refer to Figure 6

6. Press Function key until the Calibration windowappears as shown.

7. Press up arrow key to enter calibration mode.

Refer to Figure 7

8. This is the first window that appears in Calibrationmode. Press Function key to accept, or Up key tochange to metric settings.

Figure 4Initiate Calibration

22715

Figure 5Calibration Number Prompt

22778

Figure 6Press Up Key to Calibrate

22717

Figure 7Measurement Mode

22718

401-347B 08/02/2010


Refer to Figure 8

9. Enter drill width here using Up/Down arrow keys.Press Function key to advance to next window.

Refer to Figure 9

10. Enter number of rows here using Up/Down arrowkeys. Press Function key to advance to next window.

Refer to Figure 10

11. Enter your planned planting speed using Up/Downarrow keys. Calibration mode will not accept a speedhigher than 10 mph. Press Function key to advanceto next window.

Refer to Figure 11

12. Enter the amount of seed you want to measure. Forvolumetric metering, this should be at least 1⁄4 of apound. For singulated metering, at least 100 seedsshould be selected. Press Function key to advanceto next window.

Figure 8Cal. Mode Drill Width

22779

Figure 9Cal. Mode Row Count

22720

Figure 10Cal. Mode Speed

22721

Figure 11Cal. Mode Seed Target

22780

08/02/2010 401-347B


Refer to Figure 12

13. The cab console informs you of the length of timethat the drive will be operating, in order to meter theamount of seed you have requested, at the calibra-tion number, drill width, and number of rows youhave selected. Press Function key to advance tonext window.

Refer to Figure 13

14. If the screen reads TIME TOO LOW, or TIME TOOHIGH, you will need to change the amount of seedthat you will count or measure. For calibration accu-racy, the Controller firmware will not allow you to cal-ibrate at settings that would result in the driverotating for less than 4 seconds, or more that 255seconds. Press Function key to advance to next win-dow.

Refer to Figure 14

15. The drive is about to operate, meaning there is adanger of entanglement if anyone is in the drivearea.

Be sure to verify that no one is near the drive area beforeadvancing to the next step.

Refer to Figure 15

16. Only after you have verified the drive area is clear,press the up arrow key to initiate calibration mode. Ifdrive area isn’t clear, press Down arrow key to exitcalibration mode.

Figure 12Cal. Mode Time Window

22781

Figure 13Cal. Mode Time Limit Error

22782

Figure 14Cal. Mode Clear Area

22724

Figure 15Cal. Mode Area Clear

22725

401-347B 08/02/2010


Refer to Figure 16

17. Continuing to verify that the drive area is clear, pressthe Engage key to start drive rotation. PressingFunction key will exit calibration mode.

Refer to Figure 17

18. While the drive is rotating, the display window showsthe time remaining and the “Out” rate.

CONTINUE TO MONITOR DRIVE AREA DURING DRIVEROTATION. PRESS THE ENGAGE KEY (OR OFF KEY) TOSTOP DRIVE DURING CALIBRATION

Refer to Figure 18

19. After Calibration meter rotation has ended, thisscreen will appear.

Refer to Figure 19

20. Enter the actual amount metered using the Up/Downarrow keys. Press Function key to advance to nextwindow.

Figure 16Cal. Mode Initiate Motion

22726

Figure 17Cal. Mode Prompt In Motion

22783

Figure 18Cal. Mode Normal Completion

22784

Figure 19Cal. Mode Enter Seed Count

22785

08/02/2010 401-347B


Refer to Figure 20

21. A New calibration number is suggested, along withthe old calibration number.

Refer to Figure 21

22. Press Function key to advance to window shown.

23. If you wish to keep the old number, perhaps to re-runthe calibration procedure, press the Down arrow key.If you want to accept the New calibration number,press the Up arrow key.

Refer to Figure 22

24. Console window now displays the calibration numberyou have selected.

Refer to Figure 23

25. This returns you back to the beginning of Calibrationmode as shown. To re-run the Calibration procedure,follow the steps outlined above. It is suggested thatyou perform the calibration mode at least twice, andadditional replications may be needed if Target andActual amounts vary significantly.

Figure 20Calibration Number

22786

Figure 21Calibration Number

22731

Figure 22Calibration Number Accepted

22787

Figure 23Cal. Mode Recycle

22733

401-347B 08/02/2010


Speed CalibrationIn order to fine-tune the default speed calculation or toconvert to radar speed signal, the controller may be cali-brated as follows:

1. Set two flags 400ft apart (100 meters if in metricmode).

Refer to Figure 24

2. To calibrate the Controller for speed, press the Func-tion key until the screen appears, as shown.

Refer to Figure 25

3. Press up to initiate new speed calibration routine;press down to restore factory default settings.

Refer to Figure 26

4. Begin driving at a normal field speed; when the trac-tor passes the first flag, press ENGAGE.

Refer to Figure 27

5. While between flags, the display shows the distancetraveled.

Figure 24Speed Cal. Mode

22788

Figure 25Initiate Speed Calibration

22789

Figure 26At First Flag

22790

Figure 27Between Flags

22791

08/02/2010 401-347B


Refer to Figure 28

6. When the tractor passes the second flag, pressengage again.

Refer to Figure 29

7. The display will show the error or difference betweenthe traveled distance and the distance calculated bythe Controller.

Refer to Figure 30

8. If this is the first time the unit has been calibrated,this error can be large. Accept the new speed cali-bration and re-run the course. Re-calibrate until theerror is within 5%. The cab console will give you theoption each time you calibrate of accepting the newsettings, or keeping the previous settings.

Figure 28At Second Flag

22792

Figure 29Distance Variance

22793

Figure 30Save/Ignore Result

22794

401-347B 08/02/2010


Veris Calibration for Finger Meters

Note: Refer to seed rate charts for optimal plantingspeed for your desired rate. If using pre-set rates,operate planter at the optimal speed for yourmedian rate.

Note: Cal Numbers should be accurate, but Great Plainsstrongly suggests that you use the CalibrationRoutine to fine tune your actual planting rate atyour desired field speed.

Planting calibration for 12 and 16 Row Yield-Pro®

Crop Meter Type Row Spacing Min Plant Rate Max Plant Rate CAL Number

Corn 20in 6 finger meter

Corn 20in 12 finger meter 23,100 54,100 1386*

* Refer to the seed rate charts for maximum planting speed for your desired rate. If using pre-set rates, make sure thatyou don’t exceed maximum planting speed while in high rate.

Corn Twin Row 30in 6 finger meter 15,400 54,100 924*

Corn Twin Row 30in 12 finger meter 30,200 54,100 1848*

Corn 30in 6 finger meter 13,300 28,800 462*

Corn 30in 12finger meter 15,400 54,100 924*

Corn Twin Row 36in 6 finger meter 18,500 50,000 770†

† Extremely high rates on wide row spacing may require lower ground speed - refer to seed charts for mph limitations.

Corn Twin Row 36in 12 finger meter

Corn 36in 6 finger meter

Corn 36in 12 finger meter 18,500 50,000 770†

08/02/2010 401-347B


Veris Calibration for Singulating Meters


Crop Meter Type Row Spacing Min Plant Rate Max Plant Rate CAL Number

Corn Twin Row 30in 28 cell meter 15,500 42,100 4313*

Corn Twin Row 36in 28 cell meter 15,500 42,100 3594†

Cotton Twin Row 30in 120 cell meter 66,500 180,500 18485*

Cotton 30in 120 cell meter 33,200 90,200 9242†

Cotton Twin Row 36in 120 cell meter 55,400 150,400 15404†

Cotton 36in 120 cell meter 28,300 76,700 7702†

Milo 15in 51 cell meter 28,300 76,700 7855*

Milo Twin Row 30in 51 cell meter 28,300 76,700 7856*


Milo 30in 51 cell meter 28,300 76,700 3928†

Milo Twin Row 36in 51 cell meter 28,300 76,700 6547†

















401-347B 08/02/2010


Note: Refer to seed rate charts for optimal plantingspeed for your desired rate. If using pre-set rates,operate planter at the optimal speed for yourmedian rate.

Note: Cal Numbers should be accurate, but Great Plainsstrongly suggests that you use the CalibrationRoutine to fine tune your actual planting rate atyour desired field speed.




Soybeans

15in 100 cell meter 110,900 300,800 15402*

Soybeans

Twin Row 30in 100 cell meter 110,900 300,800 15404*

Soybeans

20in 100 cell meter 110,900 300,800 11553*

Soybeans

30in 100 cell meter 110,900 300,800 7702†

Soybeans

Twin Row 36in 100 cell meter 110,900 300,800 12837†

Soybeans

36in 100 cell meter 110,900 300,800 6418†

Soybeans

15in 110 cell meter 121,900 330,900 16942*

Soybeans

Twin Row 30in 110 cell meter 121,900 330,900 16944*

Soybeans

20in 110 cell meter 121,900 330,900 12708*

Soybeans

30in 110 cell meter 121,900 330,900 8472†

Soybeans

Twin Row 36in 110 cell meter 121,900 330,900 14120†

Soybeans

36in 110 cell meter 121,900 330,900 7060†

* Refer to the seed rate charts for maximum planting speed for your desired rate. If using pre-set rates, make sure thatyou don’t exceed maximum planting speed while in high rate.

† Extremely high rates on wide row spacing may require lower ground speed - refer to seed charts for mph limitations.


08/02/2010 401-347B


Singulating Meter Planting

Singulating meter planting rate is determined by:

• crop and seed variant

• meter wheel selection, and

• meter drive configuration

There are no other adjustments.

Reading a Singulated Rate Chart1. Consult the chart for your:

crop,meter wheel/cell count, androw spacing.

See “Seed Lubricants” on page 60 for seed lubricant infor-mation.

2. Find the columns for your row spacing.

3. Find the desired seed population range (or seedspacing).

4. Note the maximum ground speed for that popula-tion.

With hydraulic meter drive, enter the population andwheel cell count in the seed monitor. With ground drive,configure the sprockets.

Ground Drive5. The Range sprockets are at the top of the columns

for the row spacing.

6. The Transmission sprockets are in the table rows,found to the left of the Population.

p

YP 1225 - 1625 SOYBEAN100 Cell Wheel Precision Meter403-122D - 1700-2200 seeds/lb

Twin Row 30in Twin Row 36in 20in Rows 315in Rows

Range Sprockets: Range Sprockets: Range Sprockets: Ran

Driving =15 Driving = 18 Driving =20 Drivi

Driven = 60 Driven = 60 Driven =60 Driv

Ezee Glide Plus Required

Precision Meter 0 seeds/lb

Twin Row 30in Twin Row 36in 20in Rows 30in Rows 36i 15in Rows

Range Sprockets: Range Sprockets: Range Sprockets: Range Sprockets: Range

Driving =15 Driving = 18 Driving =20 Driving =30 Driving

Driven = 60 Driven = 60 Driven =60 Driven =60 Driven Maximum Maximum Maximum Maximum

Seed Seed Planting Seed Planting Seed Planting Seed Planting SeedPopulation Spacing Speed Spacing Speed Spacing Speed Spacing Speed Spacin(seeds/acre) (inches) (mph) (inches) (mph) (inches) (mph) (inches) (mph) (inches

55 983 7.5 8 6.2 8 5.6 8 3.7 8 3.158 056 7.2 8 6.0 8 5.4 8 3.6 8 3.060 289 6.9 8 5.8 8 5.2 8 3.5 8 2.962 569 6 7 8 5 6 8 5 0 8 3 3 8 2 8


Maximum Maximum Maximum

Transmission Seed Seed Planting Seed Planting Seed Planting SeeCombinations Population Spacing Speed Spacing Speed Spacing Speed Spac

Driver Driven (seeds/acre) (inches) (mph) (inches) (mph) (inches) (mph) (inch17 28 61 581 6.8 8 5.7 8 5.1 8 3.417 27 63 862 6.5 8 5.5 8 4.9 8 3.317 26 66 318 6.3 8 5.3 8 4.7 8 3.219 28 68 826 6.1 8 5.1 8 4.6 8 3.017 25 68 971 6.1 8 5.1 8 4.5 8 3.019 27 71 375 5.9 8 4.9 8 4.4 8 2.917 24 71 845 5.8 8 4.9 8 4.4 8 2.919 26 74 120 5.6 8 4.7 8 4.2 8 2.817 23 74 968 5.6 8 4.6 8 4.2 8 2.819 25 77 085 5.4 8 4.5 8 4.1 8 2.719 24 80 297 5.2 8 4.3 8 3.9 8 2.623 28 83 315 5.0 8 4.2 8 3.8 8 2.519 23 83 788 5.0 8 4.2 8 3.7 8 2.5

403-125D 3100-3800 seeds/lb Twin Row 30in Twin Row 36in 20in 403-126D 3600-4000 seeds/lb 15in Rows

Range Sprockets: Range Sprockets: Range S

Driving =15 Driving = 18 Driving

Driven = 60 Driven = 60 Driven Maximum Maximum

Transmission Seed Seed Planting Seed Planting SeedCombinations Population Spacing Speed Spacing Speed Spacing

Driver Driven (seeds/acre) (inches) (mph) (inches) (mph) (inches)17 28 61 581 6.8 8 5.7 8 5.117 27 63 862 6.5 8 5.5 8 4.917 26 66 318 6.3 8 5.3 8 4.719 28 68 826 6.1 8 5.1 8 4.617 25 68 971 6.1 8 5.1 8 4.519 27 71 375 5.9 8 4.9 8 4.417 24 71 845 5.8 8 4.9 8 4.419 26 74 120 5.6 8 4.7 8 4.217 23 74 968 5.6 8 4.6 8 4.219 25 77 085 5 4 8 4 5 8 4 1

401-347B 08/02/2010


YP 1225 - 1625 COTTON120 Cell Wheel403-133D - 4000-4600 seeds/lb Precision Meter403-134D - 4600-5200 seeds/lb403-135D - 5200-6000 seeds/lb

Twin Row 30in 30in RowsRange Sprockets: Range Sprockets:

Driving = 15 Driving = 15Driven = 60 Driven = 60

Transmission Seed Seed Planting Seed Seed Planting

Combinations Population Spacing Speed Population Spacing SpeedDriving Driven (seeds/acre) (inches) (mph) (seeds/acre) (inches) (mph)

17 28 67 179 6.2 8 33 590 6.2 8

17 27 69 667 6.0 8 34 834 6.0 8

17 26 72 347 5.8 8 36 173 5.8 8

19 28 75 083 5.6 8 37 541 5.6 8

17 25 75 241 5.6 8 37 620 5.6 8

19 27 77 864 5.4 8 38 932 5.4 8

17 24 78 376 5.3 8 39 188 5.3 8

19 26 80 858 5.2 8 40 429 5.2 8

17 23 81 783 5.1 8 40 892 5.1 8

19 25 84 093 5.0 8 42 046 5.0 8

19 24 87 597 4.8 8 43 798 4.8 8

23 28 90 890 4.6 8 45 445 4.6 8

19 23 91 405 4.6 8 45 703 4.6 8

23 27 94 256 4.4 8 47 128 4.4 8

24 28 94 841 4.4 8 47 421 4.4 8

23 26 97 881 4.3 8 48 941 4.3 8

24 27 98 354 4.3 8 49 177 4.3 8

25 28 98 793 4.2 8 49 397 4.2 8

17 19 99 001 4.2 8 49 501 4.2 8

23 25 101 796 4.1 8 50 898 4.1 8

24 26 102 137 4.1 8 51 068 4.1 8

25 27 102 452 4.1 8 51 226 4.1 8

26 28 102 745 4.1 8 51 372 4.1 8

23 24 106 038 3.9 8 53 019 3.9 8

24 25 106 222 3.9 8 53 111 3.9 8

25 26 106 393 3.9 8 53 196 3.9 8

26 27 106 550 3.9 8 53 275 3.9 8

27 28 106 697 3.9 8 53 348 3.9 8

23 23 110 648 3.8 8 55 324 3.8 8

28 27 114 746 3.6 8 57 373 3.6 8

27 26 114 904 3.6 8 57 452 3.6 8

26 25 115 074 3.6 8 57 537 3.6 8

25 24 115 259 3.6 8 57 629 3.6 8

24 23 115 459 3.6 8 57 730 3.6 8

28 26 119 160 3.5 8 59 580 3.5 8

27 25 119 500 3.5 8 59 750 3.5 8

26 24 119 869 3.5 8 59 934 3.5 8

25 23 120 270 3.5 8 60 135 3.5 8

19 17 123 666 3.4 8 61 833 3.4 8

28 25 123 926 3.4 8 61 963 3.4 8

27 24 124 479 3.4 8 62 240 3.4 8

26 23 125 081 3.3 8 62 540 3.3 8

28 24 129 090 3.2 8 64 545 3.2 8

27 23 129 891 3.2 8 64 946 3.2 8

23 19 133 943 3.1 7 66 971 3.1 7

28 23 134 702 3.1 7 67 351 3.1 7

24 19 139 766 3.0 7 69 883 3.0 7

25 19 145 590 2.9 7 72 795 2.9 7

23 17 149 701 2.8 6 74 850 2.8 6

26 19 151 413 2.8 6 75 707 2.8 6

24 17 156 209 2.7 6 78 105 2.7 6

27 19 157 237 2.7 6 78 618 2.7 6

25 17 162 718 2.6 6 81 359 2.6 6

28 19 163 061 2.6 6 81 530 2.6 6

26 17 169 227 2.5 6 84 613 2.5 6

27 17 175 735 2.4 5 87 868 2.4 5

28 17 182 244 2.3 5 91 122 2.3 531213

TwinRow 30in & 30in Rows


08/02/2010 401-347B


YP 1225 - 1625 COTTON120 Cell Wheel403-133D - 4000-4600 seeds/lb Precision Meter403-134D - 4600-5200 seeds/lb403-135D - 5200-6000 seeds/lb

Twin Row 36in 36in RowsRange Sprockets: Range Sprockets:


Transmission Seed Seed Planting Seed Seed Planting

Combinations Population Spacing Speed Population Spacing SpeedDriving Driven (seeds/acre) (inches) (mph) (seeds/acre) (inches) (mph)

17 28 55 983 6.2 8 27 991 6.2 8

17 27 58 056 6.0 8 29 028 6.0 8

17 26 60 289 5.8 8 30 145 5.8 8

19 28 62 569 5.6 8 31 284 5.6 8

17 25 62 701 5.6 8 31 350 5.6 8

19 27 64 886 5.4 8 32 443 5.4 8

17 24 65 313 5.3 8 32 657 5.3 8

19 26 67 382 5.2 8 33 691 5.2 8

17 23 68 153 5.1 8 34 076 5.1 8

19 25 70 077 5.0 8 35 039 5.0 8

19 24 72 997 4.8 8 36 499 4.8 8

23 28 75 741 4.6 8 37 871 4.6 8

19 23 76 171 4.6 8 38 085 4.6 8

23 27 78 547 4.4 8 39 273 4.4 8

24 28 79 034 4.4 8 39 517 4.4 8

23 26 81 568 4.3 8 40 784 4.3 8

24 27 81 962 4.3 8 40 981 4.3 8

25 28 82 328 4.2 8 41 164 4.2 8

17 19 82 501 4.2 8 41 250 4.2 8

23 25 84 830 4.1 8 42 415 4.1 8

24 26 85 114 4.1 8 42 557 4.1 8

25 27 85 377 4.1 8 42 688 4.1 8

26 28 85 621 4.1 8 42 810 4.1 8

23 24 88 365 3.9 8 44 182 3.9 8

24 25 88 519 3.9 8 44 259 3.9 8

25 26 88 660 3.9 8 44 330 3.9 8

26 27 88 792 3.9 8 44 396 3.9 8

27 28 88 914 3.9 8 44 457 3.9 8

23 23 92 207 3.8 8 46 103 3.8 8

28 27 95 622 3.6 8 47 811 3.6 8

27 26 95 753 3.6 8 47 877 3.6 8

26 25 95 895 3.6 8 47 948 3.6 8

25 24 96 049 3.6 8 48 024 3.6 8

24 23 96 216 3.6 8 48 108 3.6 8

28 26 99 300 3.5 8 49 650 3.5 8

27 25 99 583 3.5 8 49 792 3.5 8

26 24 99 891 3.5 8 49 945 3.5 8

25 23 100 225 3.5 8 50 112 3.5 8

19 17 103 055 3.4 8 51 527 3.4 8

28 25 103 272 3.4 8 51 636 3.4 8

27 24 103 733 3.4 8 51 866 3.4 8

26 23 104 234 3.3 8 52 117 3.3 8

28 24 107 575 3.2 8 53 787 3.2 8

27 23 108 243 3.2 8 54 121 3.2 8

23 19 111 619 3.1 7 55 809 3.1 7

28 23 112 252 3.1 7 56 126 3.1 7

24 19 116 472 3.0 7 58 236 3.0 7

25 19 121 325 2.9 7 60 662 2.9 7

23 17 124 750 2.8 6 62 375 2.8 6

26 19 126 178 2.8 6 63 089 2.8 6

24 17 130 174 2.7 6 65 087 2.7 6

27 19 131 031 2.7 6 65 515 2.7 6

25 17 135 598 2.6 6 67 799 2.6 6

28 19 135 884 2.6 6 67 942 2.6 6

26 17 141 022 2.5 6 70 511 2.5 6

27 17 146 446 2.4 5 73 223 2.4 5

28 17 151 870 2.3 5 75 935 2.3 531214

TwinRow 36in & 36in Rows


401-347B 08/02/2010


YP 1225 - 1625 MILO Low Rate102 Cell Wheel Precision Meter403-137D - 10500-18000 seeds/lb

30in Rows 36in RowsRange Sprockets: Range Sprockets:


Maximum Maximum

Transmission Seed Seed Planting Seed Planting

Combinations Population Spacing Speed Spacing SpeedDriving Driven (seeds/acre) (inches) (mph) (inches) (mph)

17 28 28 551 7.3 8 6.1 8

17 27 29 609 7.1 8 5.9 8

17 26 30 747 6.8 8 5.7 8

19 28 31 910 6.6 8 5.5 8

17 25 31 977 6.5 8 5.4 8

19 27 33 092 6.3 8 5.3 8

17 24 33 310 6.3 8 5.2 8

19 26 34 365 6.1 8 5.1 8

17 23 34 758 6.0 8 5.0 8

19 25 35 739 5.9 8 4.9 8

19 24 37 229 5.6 8 4.7 8

23 28 38 628 5.4 8 4.5 8

19 23 38 847 5.4 8 4.5 8

23 27 40 059 5.2 8 4.3 8

24 28 40 308 5.2 8 4.3 8

23 26 41 599 5.0 8 4.2 8

24 27 41 800 5.0 8 4.2 8

25 28 41 987 5.0 8 4.1 8

17 19 42 075 5.0 8 4.1 7

23 25 43 263 4.8 8 4.0 7

24 26 43 408 4.8 8 4.0 7

25 27 43 542 4.8 8 4.0 7

26 28 43 667 4.8 8 4.0 7

23 24 45 066 4.6 8 3.9 7

24 25 45 144 4.6 8 3.9 7

25 26 45 217 4.6 8 3.9 7

26 27 45 284 4.6 8 3.8 7

27 28 45 346 4.6 8 3.8 7

23 23 47 026 4.4 8 3.7 7

28 27 48 767 4.3 8 3.6 6

27 26 48 834 4.3 8 3.6 6

26 25 48 907 4.3 8 3.6 6

25 24 48 985 4.3 8 3.6 6

24 23 49 070 4.3 8 3.6 6

28 26 50 643 4.1 7 3.4 6

27 25 50 788 4.1 7 3.4 6

26 24 50 944 4.1 7 3.4 6

25 23 51 115 4.1 7 3.4 6

19 17 52 558 4.0 7 3.3 6

28 25 52 669 4.0 7 3.3 6

27 24 52 904 4.0 7 3.3 6

26 23 53 159 3.9 7 3.3 6

28 24 54 863 3.8 7 3.2 6

27 23 55 204 3.8 7 3.2 6

23 19 56 926 3.7 7 3.1 5

28 23 57 248 3.7 7 3.0 5

24 19 59 401 3.5 6 2.9 5

25 19 61 876 3.4 6 2.8 5

23 17 63 623 3.3 6 2.7 5

26 19 64 351 3.2 6 2.7 5

24 17 66 389 3.1 6 2.6 5

27 19 66 826 3.1 6 2.6 5

25 17 69 155 3.0 5 2.5 4

28 19 69 301 3.0 5 2.5 4

26 17 71 921 2.9 5 2.4 4

27 17 74 688 2.8 5 2.3 4

28 17 77 454 2.7 5 2.2 431215


08/02/2010 401-347B


YP 1225 - 1625 MILO102 Cell Wheel Precision Meter403-137D - 10500-18000 seeds/lb

Twin Row 30in Twin Row 36in 20in Rows 30in Rows 36in Rows15in Rows

Range Sprockets: Range Sprockets: Range Sprockets: Range Sprockets: Range Sprockets:

Driving = 15 Driving = 18 Driving = 20 Driving = 15 Driving = 18Driven = 60 Driven = 60 Driven = 60 Driven = 30 Driven = 30

Maximum Maximum Maximum Maximum Maximum

Transmission Seed Seed Planting Seed Planting Seed Planting Seed Planting Seed Planting

Combinations Population Spacing Speed Spacing Speed Spacing Speed Spacing Speed Spacing SpeedDriving Driven (seeds/acre) (inches) (mph) (inches) (mph) (inches) (mph) (inches) (mph) (inches) (mph)

17 28 57 102 7.3 8 6.1 8 5.5 8 3.7 7 3.1 5

17 27 59 217 7.1 8 5.9 8 5.3 8 3.5 6 2.9 5

17 26 61 495 6.8 8 5.7 8 5.1 8 3.4 6 2.8 5

19 28 63 820 6.6 8 5.5 8 4.9 8 3.3 6 2.7 5

17 25 63 955 6.5 8 5.4 8 4.9 8 3.3 6 2.7 5

19 27 66 184 6.3 8 5.3 8 4.7 8 3.2 6 2.6 5

17 24 66 619 6.3 8 5.2 8 4.7 8 3.1 6 2.6 5

19 26 68 730 6.1 8 5.1 8 4.6 8 3.0 5 2.5 4

17 23 69 516 6.0 8 5.0 8 4.5 8 3.0 5 2.5 4

19 25 71 479 5.9 8 4.9 8 4.4 8 2.9 5 2.4 4

19 24 74 457 5.6 8 4.7 8 4.2 8 2.8 5 2.3 4

23 28 77 256 5.4 8 4.5 8 4.1 7 2.7 5 2.3 4

19 23 77 694 5.4 8 4.5 8 4.0 7 2.7 5 2.2 4

23 27 80 118 5.2 8 4.3 8 3.9 7 2.6 5 2.2 4

24 28 80 615 5.2 8 4.3 8 3.9 7 2.6 5 2.2 4

23 26 83 199 5.0 8 4.2 8 3.8 7 2.5 4 2.1 4

24 27 83 601 5.0 8 4.2 8 3.8 7 2.5 4 2.1 4

25 28 83 974 5.0 8 4.1 8 3.7 7 2.5 4 2.1 4

17 19 84 151 5.0 8 4.1 7 3.7 7 2.5 4 2.1 3

23 25 86 527 4.8 8 4.0 7 3.6 7 2.4 4 2.0 3

24 26 86 816 4.8 8 4.0 7 3.6 6 2.4 4 2.0 3

25 27 87 084 4.8 8 4.0 7 3.6 6 2.4 4 2.0 3

26 28 87 333 4.8 8 4.0 7 3.6 6 2.4 4 2.0 3

23 24 90 132 4.6 8 3.9 7 3.5 6 2.3 4 1.9 3

24 25 90 289 4.6 8 3.9 7 3.5 6 2.3 4 1.9 3

25 26 90 434 4.6 8 3.9 7 3.5 6 2.3 4 1.9 3

26 27 90 568 4.6 8 3.8 7 3.5 6 2.3 4 1.9 3

27 28 90 692 4.6 8 3.8 7 3.5 6 2.3 4 1.9 3

23 23 94 051 4.4 8 3.7 7 3.3 6 2.2 4 1.9 3

28 27 97 534 4.3 8 3.6 6 3.2 6 2.1 4 1.8 3

27 26 97 668 4.3 8 3.6 6 3.2 6 2.1 4 1.8 3

26 25 97 813 4.3 8 3.6 6 3.2 6 2.1 4 1.8 3

25 24 97 970 4.3 8 3.6 6 3.2 6 2.1 4 1.8 3

24 23 98 140 4.3 8 3.6 6 3.2 6 2.1 4 1.8 3

28 26 101 286 4.1 7 3.4 6 3.1 5 2.1 3 1.7 3

27 25 101 575 4.1 7 3.4 6 3.1 5 2.1 3 1.7 3

26 24 101 889 4.1 7 3.4 6 3.1 5 2.1 3 1.7 3

25 23 102 229 4.1 7 3.4 6 3.1 5 2.0 3 1.7 3

19 17 105 116 4.0 7 3.3 6 3.0 5 2.0 3 1.7 3

28 25 105 337 4.0 7 3.3 6 3.0 5 2.0 3 1.7 3

27 24 105 807 4.0 7 3.3 6 3.0 5 2.0 3 1.6 3

26 23 106 319 3.9 7 3.3 6 2.9 5 2.0 3 1.6 3

28 24 109 726 3.8 7 3.2 6 2.9 5 1.9 3 1.6 3

27 23 110 408 3.8 7 3.2 6 2.8 5 1.9 3 1.6 3

23 19 113 851 3.7 7 3.1 5 2.8 5 1.8 3 1.5 2

28 23 114 497 3.7 7 3.0 5 2.7 5 1.8 3 1.5 2

24 19 118 801 3.5 6 2.9 5 2.6 5 1.8 3 1.5 2

25 19 123 751 3.4 6 2.8 5 2.5 4 1.7 3 1.4 2

23 17 127 245 3.3 6 2.7 5 2.5 4 1.6 3 1.4 2

26 19 128 701 3.2 6 2.7 5 2.4 4 1.6 3 1.4 2

24 17 132 778 3.1 6 2.6 5 2.4 4 1.6 3 1.3 2

27 19 133 651 3.1 6 2.6 5 2.3 4 1.6 3 1.3 2

25 17 138 310 3.0 5 2.5 4 2.3 4 1.5 2 1.3 2

28 19 138 601 3.0 5 2.5 4 2.3 4 1.5 2 1.3 2

26 17 143 843 2.9 5 2.4 4 2.2 4 1.5 2 1.2 2

27 17 149 375 2.8 5 2.3 4 2.1 4 1.4 2 1.2 2

28 17 154 908 2.7 5 2.2 4 2.0 3 1.3 2 1.1 231216


401-347B 08/02/2010


YP 1225 - 1625 MILO Low Rate135 Cell Wheel Precision Meter403-140D - 12000-18000 seeds/lb403-138D - 10500-14000 seeds/lb

30in Rows 36in RowsRange Sprockets: Range Sprockets:


Maximum Maximum

Transmission Seed Seed Planting Seed Planting

Combinations Population Spacing Speed Spacing SpeedDriving Driven (seeds/acre) (inches) (mph) (inches) (mph)

17 28 37 788 5.5 8 4.6 8

17 27 39 188 5.3 8 4.4 8

17 26 40 695 5.1 8 4.3 8

19 28 42 234 5.0 8 4.1 8

17 25 42 323 4.9 8 4.1 8

19 27 43 798 4.8 8 4.0 8

17 24 44 086 4.7 8 4.0 8

19 26 45 483 4.6 8 3.8 8

17 23 46 003 4.5 8 3.8 8

19 25 47 302 4.4 8 3.7 8

19 24 49 273 4.2 8 3.5 8

23 28 51 125 4.1 8 3.4 8

19 23 51 415 4.1 8 3.4 8

23 27 53 019 3.9 8 3.3 8

24 28 53 348 3.9 8 3.3 8

23 26 55 058 3.8 8 3.2 8

24 27 55 324 3.8 8 3.1 8

25 28 55 571 3.8 8 3.1 8

17 19 55 688 3.8 8 3.1 7

23 25 57 260 3.7 8 3.0 7

24 26 57 452 3.6 8 3.0 7

25 27 57 629 3.6 8 3.0 7

26 28 57 794 3.6 8 3.0 7

23 24 59 646 3.5 8 2.9 7

24 25 59 750 3.5 8 2.9 7

25 26 59 846 3.5 8 2.9 7

26 27 59 934 3.5 8 2.9 7

27 28 60 017 3.5 8 2.9 7

23 23 62 240 3.4 8 2.8 7

28 27 64 545 3.2 8 2.7 6

27 26 64 633 3.2 8 2.7 6

26 25 64 729 3.2 8 2.7 6

25 24 64 833 3.2 8 2.7 6

24 23 64 946 3.2 8 2.7 6

28 26 67 027 3.1 7 2.6 6

27 25 67 219 3.1 7 2.6 6

26 24 67 426 3.1 7 2.6 6

25 23 67 652 3.1 7 2.6 6

19 17 69 562 3.0 7 2.5 6

28 25 69 708 3.0 7 2.5 6

27 24 70 020 3.0 7 2.5 6

26 23 70 358 3.0 7 2.5 6

28 24 72 613 2.9 7 2.4 6

27 23 73 064 2.9 7 2.4 6

23 19 75 343 2.8 7 2.3 5

28 23 75 770 2.8 7 2.3 5

24 19 78 618 2.7 6 2.2 5

25 19 81 894 2.6 6 2.1 5

23 17 84 207 2.5 6 2.1 5

26 19 85 170 2.5 6 2.0 5

24 17 87 868 2.4 6 2.0 5

27 19 88 446 2.4 6 2.0 5

25 17 91 529 2.3 5 1.9 4

28 19 91 722 2.3 5 1.9 4

26 17 95 190 2.2 5 1.8 4

27 17 98 851 2.1 5 1.8 4

28 17 102 512 2.0 5 1.7 431217


08/02/2010 401-347B


YP 1225 - 1625 MILO135 Cell Wheel Precision Meter403-140D - 12000-18000 seeds/lb403-138D - 10500-14000 seeds/lb







17 28 75 577 5.5 8 4.6 8 4.1 8 2.8 7 2.3 5

17 27 78 376 5.3 8 4.4 8 4.0 8 2.7 6 2.2 5

17 26 81 390 5.1 8 4.3 8 3.9 8 2.6 6 2.1 5

19 28 84 468 5.0 8 4.1 8 3.7 8 2.5 6 2.1 5

17 25 84 646 4.9 8 4.1 8 3.7 8 2.5 6 2.1 5

19 27 87 597 4.8 8 4.0 8 3.6 8 2.4 6 2.0 5

17 24 88 173 4.7 8 4.0 8 3.6 8 2.4 6 2.0 5

19 26 90 966 4.6 8 3.8 8 3.4 8 2.3 5 1.9 4

17 23 92 006 4.5 8 3.8 8 3.4 8 2.3 5 1.9 4

19 25 94 604 4.4 8 3.7 8 3.3 8 2.2 5 1.8 4

19 24 98 546 4.2 8 3.5 8 3.2 8 2.1 5 1.8 4

23 28 102 251 4.1 8 3.4 8 3.1 7 2.0 5 1.7 4

19 23 102 831 4.1 8 3.4 8 3.0 7 2.0 5 1.7 4

23 27 106 038 3.9 8 3.3 8 3.0 7 2.0 5 1.6 4

24 28 106 697 3.9 8 3.3 8 2.9 7 2.0 5 1.6 4

23 26 110 116 3.8 8 3.2 8 2.8 7 1.9 4 1.6 4

24 27 110 648 3.8 8 3.1 8 2.8 7 1.9 4 1.6 4

25 28 111 142 3.8 8 3.1 8 2.8 7 1.9 4 1.6 4

17 19 111 376 3.8 8 3.1 7 2.8 7 1.9 4 1.6 3

23 25 114 521 3.7 8 3.0 7 2.7 7 1.8 4 1.5 3

24 26 114 904 3.6 8 3.0 7 2.7 6 1.8 4 1.5 3

25 27 115 259 3.6 8 3.0 7 2.7 6 1.8 4 1.5 3

26 28 115 588 3.6 8 3.0 7 2.7 6 1.8 4 1.5 3

23 24 119 293 3.5 8 2.9 7 2.6 6 1.8 4 1.5 3

24 25 119 500 3.5 8 2.9 7 2.6 6 1.7 4 1.5 3

25 26 119 692 3.5 8 2.9 7 2.6 6 1.7 4 1.5 3

26 27 119 869 3.5 8 2.9 7 2.6 6 1.7 4 1.5 3

27 28 120 034 3.5 8 2.9 7 2.6 6 1.7 4 1.5 3

23 23 124 479 3.4 8 2.8 7 2.5 6 1.7 4 1.4 3

28 27 129 090 3.2 8 2.7 6 2.4 6 1.6 4 1.3 3

27 26 129 267 3.2 8 2.7 6 2.4 6 1.6 4 1.3 3

26 25 129 458 3.2 8 2.7 6 2.4 6 1.6 4 1.3 3

25 24 129 666 3.2 8 2.7 6 2.4 6 1.6 4 1.3 3

24 23 129 891 3.2 8 2.7 6 2.4 6 1.6 4 1.3 3

28 26 134 055 3.1 7 2.6 6 2.3 5 1.6 3 1.3 3

27 25 134 438 3.1 7 2.6 6 2.3 5 1.6 3 1.3 3

26 24 134 853 3.1 7 2.6 6 2.3 5 1.6 3 1.3 3

25 23 135 304 3.1 7 2.6 6 2.3 5 1.5 3 1.3 3

19 17 139 124 3.0 7 2.5 6 2.3 5 1.5 3 1.3 3

28 25 139 417 3.0 7 2.5 6 2.2 5 1.5 3 1.2 3

27 24 140 039 3.0 7 2.5 6 2.2 5 1.5 3 1.2 3

26 23 140 716 3.0 7 2.5 6 2.2 5 1.5 3 1.2 3

28 24 145 226 2.9 7 2.4 6 2.2 5 1.4 3 1.2 3

27 23 146 128 2.9 7 2.4 6 2.1 5 1.4 3 1.2 3

23 19 150 685 2.8 7 2.3 5 2.1 5 1.4 3 1.2 2

28 23 151 540 2.8 7 2.3 5 2.1 5 1.4 3 1.1 2

24 19 157 237 2.7 6 2.2 5 2.0 5 1.3 3 1.1 2

25 19 163 789 2.6 6 2.1 5 1.9 4 1.3 3 1.1 2

23 17 168 413 2.5 6 2.1 5 1.9 4 1.2 3 1.0 2

26 19 170 340 2.5 6 2.0 5 1.8 4 1.2 3 1.0 2

24 17 175 735 2.4 6 2.0 5 1.8 4 1.2 3 1.0 2

27 19 176 892 2.4 6 2.0 5 1.8 4 1.2 3 1.0 2

25 17 183 058 2.3 5 1.9 4 1.7 4 1.1 2 1.0 2

28 19 183 443 2.3 5 1.9 4 1.7 4 1.1 2 0.9 2

26 17 190 380 2.2 5 1.8 4 1.6 4 1.1 2 0.9 2

27 17 197 702 2.1 5 1.8 4 1.6 4 1.1 2 0.9 2

28 17 205 025 2.0 5 1.7 4 1.5 3 1.0 2 0.8 231218


401-347B 08/02/2010


YP 1225 - 1625 MILO270 Cell Wheel Precision Meter403-141D - 12000-18000 seeds/lb403-139D - 10500-14000 seeds/lb







17 28 151 153 2.8 8 2.3 8 2.1 8 1.4 7 1.2 5

17 27 156 752 2.7 8 2.2 8 2.0 8 1.3 6 1.1 5

17 26 162 781 2.6 8 2.1 8 1.9 8 1.3 6 1.1 5

19 28 168 936 2.5 8 2.1 8 1.9 8 1.2 6 1.0 5

17 25 169 292 2.5 8 2.1 8 1.9 8 1.2 6 1.0 5

19 27 175 193 2.4 8 2.0 8 1.8 8 1.2 6 1.0 5

17 24 176 346 2.4 8 2.0 8 1.8 8 1.2 6 1.0 5

19 26 181 931 2.3 8 1.9 8 1.7 8 1.1 5 1.0 4

17 23 184 013 2.3 8 1.9 8 1.7 8 1.1 5 0.9 4

19 25 189 208 2.2 8 1.8 8 1.7 8 1.1 5 0.9 4

19 24 197 092 2.1 8 1.8 8 1.6 8 1.1 5 0.9 4

23 28 204 502 2.0 8 1.7 8 1.5 7 1.0 5 0.9 4

19 23 205 661 2.0 8 1.7 8 1.5 7 1.0 5 0.8 4

23 27 212 076 2.0 8 1.6 8 1.5 7 1.0 5 0.8 4

24 28 213 393 2.0 8 1.6 8 1.5 7 1.0 5 0.8 4

23 26 220 233 1.9 8 1.6 8 1.4 7 0.9 4 0.8 4

24 27 221 296 1.9 8 1.6 8 1.4 7 0.9 4 0.8 4

25 28 222 284 1.9 8 1.6 8 1.4 7 0.9 4 0.8 4

17 19 222 752 1.9 8 1.6 7 1.4 7 0.9 4 0.8 3

23 25 229 042 1.8 8 1.5 7 1.4 7 0.9 4 0.8 3

24 26 229 808 1.8 8 1.5 7 1.4 6 0.9 4 0.8 3

25 27 230 517 1.8 8 1.5 7 1.4 6 0.9 4 0.8 3

26 28 231 176 1.8 8 1.5 7 1.4 6 0.9 4 0.8 3

23 24 238 585 1.8 8 1.5 7 1.3 6 0.9 4 0.7 3

24 25 239 000 1.7 8 1.5 7 1.3 6 0.9 4 0.7 3

25 26 239 383 1.7 8 1.5 7 1.3 6 0.9 4 0.7 3

26 27 239 738 1.7 8 1.5 7 1.3 6 0.9 4 0.7 3

27 28 240 067 1.7 8 1.5 7 1.3 6 0.9 4 0.7 3

23 23 248 959 1.7 8 1.4 7 1.3 6 0.8 4 0.7 3

28 27 258 179 1.6 8 1.3 6 1.2 6 0.8 4 0.7 3

27 26 258 534 1.6 8 1.3 6 1.2 6 0.8 4 0.7 3

26 25 258 917 1.6 8 1.3 6 1.2 6 0.8 4 0.7 3

25 24 259 332 1.6 8 1.3 6 1.2 6 0.8 4 0.7 3

24 23 259 783 1.6 8 1.3 6 1.2 6 0.8 4 0.7 3

28 26 268 109 1.6 7 1.3 6 1.2 5 0.8 3 0.6 3

27 25 268 875 1.6 7 1.3 6 1.2 5 0.8 3 0.6 3

26 24 269 705 1.6 7 1.3 6 1.2 5 0.8 3 0.6 3

25 23 270 607 1.5 7 1.3 6 1.2 5 0.8 3 0.6 3

19 17 278 248 1.5 7 1.3 6 1.1 5 0.8 3 0.6 3

28 25 278 834 1.5 7 1.2 6 1.1 5 0.7 3 0.6 3

27 24 280 078 1.5 7 1.2 6 1.1 5 0.7 3 0.6 3

26 23 281 431 1.5 7 1.2 6 1.1 5 0.7 3 0.6 3

28 24 290 452 1.4 7 1.2 6 1.1 5 0.7 3 0.6 3

27 23 292 256 1.4 7 1.2 6 1.1 5 0.7 3 0.6 3

23 19 301 371 1.4 7 1.2 5 1.0 5 0.7 3 0.6 2

28 23 303 080 1.4 7 1.1 5 1.0 5 0.7 3 0.6 2

24 19 314 474 1.3 6 1.1 5 1.0 5 0.7 3 0.6 2

25 19 327 577 1.3 6 1.1 5 1.0 4 0.6 3 0.5 2

23 17 336 826 1.2 6 1.0 5 0.9 4 0.6 3 0.5 2

26 19 340 680 1.2 6 1.0 5 0.9 4 0.6 3 0.5 2

24 17 351 471 1.2 6 1.0 5 0.9 4 0.6 3 0.5 2

27 19 353 783 1.2 6 1.0 5 0.9 4 0.6 3 0.5 2

25 17 366 116 1.1 5 1.0 4 0.9 4 0.6 2 0.5 2

28 19 366 886 1.1 5 0.9 4 0.9 4 0.6 2 0.5 2

26 17 380 760 1.1 5 0.9 4 0.8 4 0.5 2 0.5 2

27 17 395 405 1.1 5 0.9 4 0.8 4 0.5 2 0.4 2

28 17 410 049 1.0 5 0.8 4 0.8 3 0.5 2 0.4 231219


08/02/2010 401-347B


YP 1225 - 1625 SOYBEAN Page 1 of 2 100 Cell Wheel Precision Meter403-122D - 1700-2200 seeds/lb







17 28 55 983 7.5 8 6.2 8 5.6 8 3.7 8 3.1 8

17 27 58 056 7.2 8 6.0 8 5.4 8 3.6 8 3.0 8

17 26 60 289 6.9 8 5.8 8 5.2 8 3.5 8 2.9 8

19 28 62 569 6.7 8 5.6 8 5.0 8 3.3 8 2.8 8

17 25 62 701 6.7 8 5.6 8 5.0 8 3.3 8 2.8 8

19 27 64 886 6.4 8 5.4 8 4.8 8 3.2 8 2.7 8

17 24 65 313 6.4 8 5.3 8 4.8 8 3.2 8 2.7 8

19 26 67 382 6.2 8 5.2 8 4.7 8 3.1 8 2.6 8

17 23 68 153 6.1 8 5.1 8 4.6 8 3.1 8 2.6 7

19 25 70 077 6.0 8 5.0 8 4.5 8 3.0 8 2.5 7

19 24 72 997 5.7 8 4.8 8 4.3 8 2.9 8 2.4 7

23 28 75 741 5.5 8 4.6 8 4.1 8 2.8 8 2.3 7

19 23 76 171 5.5 8 4.6 8 4.1 8 2.7 8 2.3 7

23 27 78 547 5.3 8 4.4 8 4.0 8 2.7 8 2.2 6

24 28 79 034 5.3 8 4.4 8 4.0 8 2.6 8 2.2 6

23 26 81 568 5.1 8 4.3 8 3.8 8 2.6 7 2.1 6

24 27 81 962 5.1 8 4.3 8 3.8 8 2.6 7 2.1 6

25 28 82 328 5.1 8 4.2 8 3.8 8 2.5 7 2.1 6

17 19 82 501 5.1 8 4.2 8 3.8 8 2.5 7 2.1 6

23 25 84 830 4.9 8 4.1 8 3.7 8 2.5 7 2.1 6

24 26 85 114 4.9 8 4.1 8 3.7 8 2.5 7 2.0 6

25 27 85 377 4.9 8 4.1 8 3.7 8 2.4 7 2.0 6

26 28 85 621 4.9 8 4.1 8 3.7 8 2.4 7 2.0 6

23 24 88 365 4.7 8 3.9 8 3.5 8 2.4 7 2.0 6

24 25 88 519 4.7 8 3.9 8 3.5 8 2.4 7 2.0 6

25 26 88 660 4.7 8 3.9 8 3.5 8 2.4 7 2.0 6

26 27 88 792 4.7 8 3.9 8 3.5 8 2.4 7 2.0 6

27 28 88 914 4.7 8 3.9 8 3.5 8 2.4 7 2.0 6

23 23 92 207 4.5 8 3.8 8 3.4 8 2.3 7 1.9 5

28 27 95 622 4.4 8 3.6 8 3.3 8 2.2 6 1.8 5

27 26 95 753 4.4 8 3.6 8 3.3 8 2.2 6 1.8 5

26 25 95 895 4.4 8 3.6 8 3.3 8 2.2 6 1.8 5

25 24 96 049 4.4 8 3.6 8 3.3 8 2.2 6 1.8 5

24 23 96 216 4.3 8 3.6 8 3.3 8 2.2 6 1.8 5

28 26 99 300 4.2 8 3.5 8 3.2 8 2.1 6 1.8 5

27 25 99 583 4.2 8 3.5 8 3.1 8 2.1 6 1.7 5

26 24 99 891 4.2 8 3.5 8 3.1 8 2.1 6 1.7 5

25 23 100 225 4.2 8 3.5 8 3.1 8 2.1 6 1.7 5

19 17 103 055 4.1 8 3.4 8 3.0 8 2.0 6 1.7 5

28 25 103 272 4.0 8 3.4 8 3.0 8 2.0 6 1.7 5

27 24 103 733 4.0 8 3.4 8 3.0 8 2.0 6 1.7 5

26 23 104 234 4.0 8 3.3 8 3.0 8 2.0 6 1.7 5

28 24 107 575 3.9 8 3.2 8 2.9 8 1.9 6 1.6 5

27 23 108 243 3.9 8 3.2 8 2.9 8 1.9 6 1.6 5

23 19 111 619 3.7 8 3.1 8 2.8 8 1.9 5 1.6 4

28 23 112 252 3.7 8 3.1 8 2.8 8 1.9 5 1.6 4

24 19 116 472 3.6 8 3.0 8 2.7 8 1.8 5 1.5 4

25 19 121 325 3.4 8 2.9 8 2.6 8 1.7 5 1.4 4

23 17 124 750 3.4 8 2.8 8 2.5 7 1.7 5 1.4 4

26 19 126 178 3.3 8 2.8 8 2.5 7 1.7 5 1.4 4

24 17 130 174 3.2 8 2.7 8 2.4 7 1.6 4 1.3 4

27 19 131 031 3.2 8 2.7 8 2.4 7 1.6 4 1.3 4

25 17 135 598 3.1 8 2.6 7 2.3 7 1.5 4 1.3 3

28 19 135 884 3.1 8 2.6 7 2.3 7 1.5 4 1.3 3

26 17 141 022 3.0 8 2.5 7 2.2 6 1.5 4 1.2 3

27 17 146 446 2.9 8 2.4 7 2.1 6 1.4 4 1.2 3

28 17 151 870 2.8 8 2.3 7 2.1 6 1.4 4 1.1 331220


401-347B 08/02/2010


YP 1225 - 1625 SOYBEAN Page 2 of 2 100 Cell Wheel Precision Meter403-122D - 1700-2200 seeds/lb







17 28 111 965 3.7 8 3.1 8 2.8 8 1.9 5 1.6 4

17 27 116 112 3.6 8 3.0 8 2.7 8 1.8 5 1.5 4

17 26 120 578 3.5 8 2.9 8 2.6 8 1.7 5 1.4 4

19 28 125 138 3.3 8 2.8 8 2.5 7 1.7 5 1.4 4

17 25 125 401 3.3 8 2.8 8 2.5 7 1.7 5 1.4 4

19 27 129 773 3.2 8 2.7 8 2.4 7 1.6 5 1.3 4

17 24 130 626 3.2 8 2.7 8 2.4 7 1.6 4 1.3 4

19 26 134 764 3.1 8 2.6 8 2.3 7 1.6 4 1.3 4

17 23 136 306 3.1 8 2.6 7 2.3 7 1.5 4 1.3 3

19 25 140 154 3.0 8 2.5 7 2.2 6 1.5 4 1.2 3

19 24 145 994 2.9 8 2.4 7 2.1 6 1.4 4 1.2 3

23 28 151 483 2.8 8 2.3 7 2.1 6 1.4 4 1.2 3

19 23 152 342 2.7 8 2.3 7 2.1 6 1.4 4 1.1 3

23 27 157 093 2.7 8 2.2 6 2.0 6 1.3 4 1.1 3

24 28 158 069 2.6 8 2.2 6 2.0 6 1.3 4 1.1 3

23 26 163 135 2.6 7 2.1 6 1.9 5 1.3 3 1.1 3

24 27 163 923 2.6 7 2.1 6 1.9 5 1.3 3 1.1 3

25 28 164 655 2.5 7 2.1 6 1.9 5 1.3 3 1.1 3

17 19 165 002 2.5 7 2.1 6 1.9 5 1.3 3 1.1 3

23 25 169 661 2.5 7 2.1 6 1.8 5 1.2 3 1.0 3

24 26 170 228 2.5 7 2.0 6 1.8 5 1.2 3 1.0 3

25 27 170 753 2.4 7 2.0 6 1.8 5 1.2 3 1.0 3

26 28 171 241 2.4 7 2.0 6 1.8 5 1.2 3 1.0 3

23 24 176 730 2.4 7 2.0 6 1.8 5 1.2 3 1.0 3

24 25 177 037 2.4 7 2.0 6 1.8 5 1.2 3 1.0 3

25 26 177 321 2.4 7 2.0 6 1.8 5 1.2 3 1.0 3

26 27 177 584 2.4 7 2.0 6 1.8 5 1.2 3 1.0 3

27 28 177 828 2.4 7 2.0 6 1.8 5 1.2 3 1.0 3

23 23 184 414 2.3 7 1.9 5 1.7 5 1.1 3 0.9 2

28 27 191 244 2.2 6 1.8 5 1.6 5 1.1 3 0.9 2

27 26 191 507 2.2 6 1.8 5 1.6 5 1.1 3 0.9 2

26 25 191 790 2.2 6 1.8 5 1.6 5 1.1 3 0.9 2

25 24 192 098 2.2 6 1.8 5 1.6 5 1.1 3 0.9 2

24 23 192 432 2.2 6 1.8 5 1.6 5 1.1 3 0.9 2

28 26 198 599 2.1 6 1.8 5 1.6 4 1.1 3 0.9 2

27 25 199 167 2.1 6 1.7 5 1.6 4 1.0 3 0.9 2

26 24 199 782 2.1 6 1.7 5 1.6 4 1.0 3 0.9 2

25 23 200 450 2.1 6 1.7 5 1.6 4 1.0 3 0.9 2

19 17 206 109 2.0 6 1.7 5 1.5 4 1.0 3 0.8 2

28 25 206 543 2.0 6 1.7 5 1.5 4 1.0 3 0.8 2

27 24 207 465 2.0 6 1.7 5 1.5 4 1.0 3 0.8 2

26 23 208 468 2.0 6 1.7 5 1.5 4 1.0 3 0.8 2

28 24 215 149 1.9 6 1.6 5 1.5 4 1.0 3 0.8 2

27 23 216 486 1.9 6 1.6 5 1.4 4 1.0 3 0.8 2

23 19 223 238 1.9 5 1.6 4 1.4 4 0.9 2 0.8 2

28 23 224 504 1.9 5 1.6 4 1.4 4 0.9 2 0.8 2

24 19 232 944 1.8 5 1.5 4 1.3 4 0.9 2 0.7 2

25 19 242 650 1.7 5 1.4 4 1.3 4 0.9 2 0.7 2

23 17 249 501 1.7 5 1.4 4 1.3 3 0.8 2 0.7 2

26 19 252 356 1.7 5 1.4 4 1.2 3 0.8 2 0.7 2

24 17 260 349 1.6 4 1.3 4 1.2 3 0.8 2 0.7 2

27 19 262 062 1.6 4 1.3 4 1.2 3 0.8 2 0.7 2

25 17 271 197 1.5 4 1.3 3 1.2 3 0.8 2 0.6 1

28 19 271 768 1.5 4 1.3 3 1.2 3 0.8 2 0.6 1

26 17 282 045 1.5 4 1.2 3 1.1 3 0.7 2 0.6 1

27 17 292 892 1.4 4 1.2 3 1.1 3 0.7 2 0.6 1

28 17 303 740 1.4 4 1.1 3 1.0 3 0.7 2 0.6 131221


08/02/2010 401-347B


YP 1225 - 1625 SOYBEAN Page 1 of 2 110 Cell Wheel Precision Meter403-123D 2200-2700 seeds/lb403-124D 2700-3200 seeds/lb403-125D 3100-3800 seeds/lb Twin Row 30in Twin Row 36in 20in Rows 30in Rows 36in Rows403-126D 3600-4000 seeds/lb 15in Rows






17 28 61 581 6.8 8 5.7 8 5.1 8 3.4 8 2.8 8

17 27 63 862 6.5 8 5.5 8 4.9 8 3.3 8 2.7 8

17 26 66 318 6.3 8 5.3 8 4.7 8 3.2 8 2.6 8

19 28 68 826 6.1 8 5.1 8 4.6 8 3.0 8 2.5 8

17 25 68 971 6.1 8 5.1 8 4.5 8 3.0 8 2.5 8

19 27 71 375 5.9 8 4.9 8 4.4 8 2.9 8 2.4 8

17 24 71 845 5.8 8 4.9 8 4.4 8 2.9 8 2.4 8

19 26 74 120 5.6 8 4.7 8 4.2 8 2.8 8 2.4 8

17 23 74 968 5.6 8 4.6 8 4.2 8 2.8 8 2.3 8

19 25 77 085 5.4 8 4.5 8 4.1 8 2.7 8 2.3 8

19 24 80 297 5.2 8 4.3 8 3.9 8 2.6 8 2.2 8

23 28 83 315 5.0 8 4.2 8 3.8 8 2.5 8 2.1 8

19 23 83 788 5.0 8 4.2 8 3.7 8 2.5 8 2.1 7

23 27 86 401 4.8 8 4.0 8 3.6 8 2.4 8 2.0 7

24 28 86 938 4.8 8 4.0 8 3.6 8 2.4 8 2.0 7

23 26 89 724 4.7 8 3.9 8 3.5 8 2.3 8 1.9 7

24 27 90 158 4.6 8 3.9 8 3.5 8 2.3 8 1.9 7

25 28 90 560 4.6 8 3.8 8 3.5 8 2.3 8 1.9 7

17 19 90 751 4.6 8 3.8 8 3.5 8 2.3 8 1.9 7

23 25 93 313 4.5 8 3.7 8 3.4 8 2.2 8 1.9 7

24 26 93 625 4.5 8 3.7 8 3.3 8 2.2 8 1.9 7

25 27 93 914 4.5 8 3.7 8 3.3 8 2.2 8 1.9 7

26 28 94 183 4.4 8 3.7 8 3.3 8 2.2 8 1.9 7

23 24 97 201 4.3 8 3.6 8 3.2 8 2.2 8 1.8 6

24 25 97 370 4.3 8 3.6 8 3.2 8 2.1 8 1.8 6

25 26 97 526 4.3 8 3.6 8 3.2 8 2.1 8 1.8 6

26 27 97 671 4.3 8 3.6 8 3.2 8 2.1 8 1.8 6

27 28 97 805 4.3 8 3.6 8 3.2 8 2.1 8 1.8 6

23 23 101 428 4.1 8 3.4 8 3.1 8 2.1 7 1.7 6

28 27 105 184 4.0 8 3.3 8 3.0 8 2.0 7 1.7 6

27 26 105 329 4.0 8 3.3 8 3.0 8 2.0 7 1.7 6

26 25 105 485 4.0 8 3.3 8 3.0 8 2.0 7 1.7 6

25 24 105 654 4.0 8 3.3 8 3.0 8 2.0 7 1.6 6

24 23 105 837 4.0 8 3.3 8 3.0 8 2.0 7 1.6 6

28 26 109 230 3.8 8 3.2 8 2.9 8 1.9 7 1.6 6

27 25 109 542 3.8 8 3.2 8 2.9 8 1.9 7 1.6 6

26 24 109 880 3.8 8 3.2 8 2.9 8 1.9 7 1.6 6

25 23 110 247 3.8 8 3.2 8 2.8 8 1.9 7 1.6 6

19 17 113 360 3.7 8 3.1 8 2.8 8 1.8 7 1.5 5

28 25 113 599 3.7 8 3.1 8 2.8 8 1.8 7 1.5 5

27 24 114 106 3.7 8 3.1 8 2.7 8 1.8 7 1.5 5

26 23 114 657 3.6 8 3.0 8 2.7 8 1.8 6 1.5 5

28 24 118 332 3.5 8 2.9 8 2.7 8 1.8 6 1.5 5

27 23 119 067 3.5 8 2.9 8 2.6 8 1.8 6 1.5 5

23 19 122 781 3.4 8 2.8 8 2.6 8 1.7 6 1.4 5

28 23 123 477 3.4 8 2.8 8 2.5 8 1.7 6 1.4 5

24 19 128 119 3.3 8 2.7 8 2.4 8 1.6 6 1.4 5

25 19 133 457 3.1 8 2.6 8 2.4 8 1.6 5 1.3 4

23 17 137 226 3.0 8 2.5 8 2.3 8 1.5 5 1.3 4

26 19 138 796 3.0 8 2.5 8 2.3 8 1.5 5 1.3 4

24 17 143 192 2.9 8 2.4 8 2.2 8 1.5 5 1.2 4

27 19 144 134 2.9 8 2.4 8 2.2 8 1.5 5 1.2 4

25 17 149 158 2.8 8 2.3 8 2.1 8 1.4 5 1.2 4

28 19 149 472 2.8 8 2.3 8 2.1 8 1.4 5 1.2 4

26 17 155 124 2.7 8 2.2 8 2.0 7 1.3 5 1.1 4

27 17 161 091 2.6 8 2.2 8 1.9 7 1.3 4 1.1 4

28 17 167 057 2.5 8 2.1 7 1.9 7 1.3 4 1.0 331222


401-347B 08/02/2010


YIELD PRO 1225 - 1625 SOYBEAN Page 2 of 2 110 Cell Wheel Precision Meter403-123D 2200-2700 seeds/lb403-124D 2700-3200 seeds/lb403-125D 3100-3800 seeds/lb Twin Row 30in Twin Row 36in 20in Rows 30in Rows 36in Rows403-126D 3600-4000 seeds/lb 15in Rows






17 28 123 162 3.4 8 2.8 8 2.5 8 1.7 6 1.4 5

17 27 127 724 3.3 8 2.7 8 2.5 8 1.6 6 1.4 5

17 26 132 636 3.2 8 2.6 8 2.4 8 1.6 6 1.3 5

19 28 137 652 3.0 8 2.5 8 2.3 8 1.5 5 1.3 4

17 25 137 941 3.0 8 2.5 8 2.3 8 1.5 5 1.3 4

19 27 142 750 2.9 8 2.4 8 2.2 8 1.5 5 1.2 4

17 24 143 689 2.9 8 2.4 8 2.2 8 1.5 5 1.2 4

19 26 148 240 2.8 8 2.4 8 2.1 8 1.4 5 1.2 4

17 23 149 936 2.8 8 2.3 8 2.1 8 1.4 5 1.2 4

19 25 154 170 2.7 8 2.3 8 2.0 7 1.4 5 1.1 4

19 24 160 594 2.6 8 2.2 8 2.0 7 1.3 4 1.1 4

23 28 166 631 2.5 8 2.1 8 1.9 7 1.3 4 1.0 4

19 23 167 576 2.5 8 2.1 7 1.9 7 1.2 4 1.0 3

23 27 172 803 2.4 8 2.0 7 1.8 6 1.2 4 1.0 3

24 28 173 876 2.4 8 2.0 7 1.8 6 1.2 4 1.0 3

23 26 179 449 2.3 8 1.9 7 1.7 6 1.2 4 1.0 3

24 27 180 316 2.3 8 1.9 7 1.7 6 1.2 4 1.0 3

25 28 181 121 2.3 8 1.9 7 1.7 6 1.2 4 1.0 3

17 19 181 502 2.3 8 1.9 7 1.7 6 1.2 4 1.0 3

23 25 186 627 2.2 8 1.9 7 1.7 6 1.1 4 0.9 3

24 26 187 251 2.2 8 1.9 7 1.7 6 1.1 4 0.9 3

25 27 187 829 2.2 8 1.9 7 1.7 6 1.1 4 0.9 3

26 28 188 365 2.2 8 1.9 7 1.7 6 1.1 4 0.9 3

23 24 194 403 2.2 8 1.8 6 1.6 6 1.1 4 0.9 3

24 25 194 741 2.1 8 1.8 6 1.6 6 1.1 4 0.9 3

25 26 195 053 2.1 8 1.8 6 1.6 6 1.1 4 0.9 3

26 27 195 342 2.1 8 1.8 6 1.6 6 1.1 4 0.9 3

27 28 195 610 2.1 8 1.8 6 1.6 6 1.1 4 0.9 3

23 23 202 855 2.1 7 1.7 6 1.5 5 1.0 3 0.9 3

28 27 210 368 2.0 7 1.7 6 1.5 5 1.0 3 0.8 3

27 26 210 657 2.0 7 1.7 6 1.5 5 1.0 3 0.8 3

26 25 210 969 2.0 7 1.7 6 1.5 5 1.0 3 0.8 3

25 24 211 307 2.0 7 1.6 6 1.5 5 1.0 3 0.8 3

24 23 211 675 2.0 7 1.6 6 1.5 5 1.0 3 0.8 3

28 26 218 459 1.9 7 1.6 6 1.4 5 1.0 3 0.8 3

27 25 219 084 1.9 7 1.6 6 1.4 5 1.0 3 0.8 3

26 24 219 760 1.9 7 1.6 6 1.4 5 1.0 3 0.8 3

25 23 220 495 1.9 7 1.6 6 1.4 5 0.9 3 0.8 3

19 17 226 720 1.8 7 1.5 5 1.4 5 0.9 3 0.8 2

28 25 227 198 1.8 7 1.5 5 1.4 5 0.9 3 0.8 2

27 24 228 212 1.8 7 1.5 5 1.4 5 0.9 3 0.8 2

26 23 229 314 1.8 6 1.5 5 1.4 5 0.9 3 0.8 2

28 24 236 664 1.8 6 1.5 5 1.3 5 0.9 3 0.7 2

27 23 238 134 1.8 6 1.5 5 1.3 5 0.9 3 0.7 2

23 19 245 561 1.7 6 1.4 5 1.3 4 0.9 3 0.7 2

28 23 246 954 1.7 6 1.4 5 1.3 4 0.8 3 0.7 2

24 19 256 238 1.6 6 1.4 5 1.2 4 0.8 3 0.7 2

25 19 266 915 1.6 5 1.3 4 1.2 4 0.8 2 0.7 2

23 17 274 451 1.5 5 1.3 4 1.1 4 0.8 2 0.6 2

26 19 277 591 1.5 5 1.3 4 1.1 4 0.8 2 0.6 2

24 17 286 384 1.5 5 1.2 4 1.1 4 0.7 2 0.6 2

27 19 288 268 1.5 5 1.2 4 1.1 4 0.7 2 0.6 2

25 17 298 316 1.4 5 1.2 4 1.1 4 0.7 2 0.6 2

28 19 298 944 1.4 5 1.2 4 1.0 4 0.7 2 0.6 2

26 17 310 249 1.3 5 1.1 4 1.0 3 0.7 2 0.6 2

27 17 322 182 1.3 4 1.1 4 1.0 3 0.6 2 0.5 2

28 17 334 114 1.3 4 1.0 3 0.9 3 0.6 2 0.5 131223


08/02/2010 401-347B


401-347B 08/02/2010


Finger Meter Planting

The basic seed rate for finger meters is determined bythe meter finger count (6 or 12), and the drive setup.

Finger meters have two additional adjustments for opti-mum results:

1. Meter brush (see page 30)

2. Twin row indexing (see page 44)

Recommended speed is 41⁄2 to 5 miles per hour.

Excess speeds are known to deteriorate seed spacingcontrol and depth control.

Reading a Finger Meter Rate ChartHydraulic or Ground Drive1. Consult the chart for your:

row spacing,meter type (finger count).

Some charts have two Ranges (low and high).

2. Find the desired seed population or seed spacing.

3. Note the range of meter rpms suitable for that popu-lation.

The shaded rpms are the recommended rpms for most consis-tent results with flat kernel corn.

For round kernel corn, use either shaded or unshaded values.

Blank table cells represent rates/speeds that are not recom-mended regardless of seed type.

With hydraulic meter drive, enter the population in theseed monitor.

With ground drive, configure the sprockets.

Ground Drive4. Each chart page shows the Range sprockets at the

upper left.

5. The Transmission sprockets are in the table, foundto the left of the Population.

6. Use the recommended driving speed if possible.

YP 1225 - 1625 30in Rows6 Finger Meter

ATTENTION ! ! ! (For all seed corn types)

ets Driven = 15 Ground Speedssion Seed Seed 7 mph 6.5 mph 6 mph 5.5 mph 5 mph tions Population Spacing Meter Meter Meter Meter Meter

Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm)28 13 436 15.6 74 68 62 5727 13 933 15.0 70 65 5926 14 469 14.5 73 67 6128 15 017 13.9 70 6325 15 048 13.9 70 6327 15 573 13.4 72 6624 15 675 13.3 73 6626 16 172 12.9 75 6823 16 357 12.8 6925 16 819 12.4 7124 17 519 11.9 7428 18 178 11.5

23 18 281 11.4

27 18 851 11.1

28 18 968 11.0

26 19 576 10.7

27 19 671 10.6

28 19 759 10.6

19 19 800 10.6

Range Driving = 30Sprockets Driven = 15 Ground

Transmission Seed Seed 7 mph 6.5 mph 6 mph 5 5 mCombinations Population Spacing Meter Meter Meter Me

Driving Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rp17 28 13 436 15.6 74 68 617 27 13 933 15.0 70 617 26 14 469 14.5 73 619 28 15 017 13.9 717 25 15 048 13.9 719 27 15 573 13.4 717 24 15 675 13.3 719 26 16 172 12.9 717 23 16 357 12.8

19 25 16 819 12.4

19 24 17 519 11.9

23 28 18 178 11.5

19 23 18 281 11.4

23 27 18 851 11.1

24 28 18 968 11.0

23 26 19 576 10.7

24 27 19 671 10.6

25 28 19 759 10 6

08/02/2010 401-347B


Finger Meter Adjustments

Finger Meter Brush AdjustmentThe finger pick up meter has an adjustable brush.

The brush reduces or eliminates “doubles” (deliveringtwo seeds per finger), but if set too aggressively cancause “skips” (delivering no seed on some fingers). Asneeded, adjust for minimal doubles and skips.

Note: These instructions describe the current finger pick-up meter shipped with new Great Plains planters,which has an integrated adjustment lever for thebrush. If you have added pre-existing finger metersafter purchase, there is some chance that you mayhave previous model meters, adjusted by screw-driver rather than lever. If so, rely on counting de-tents to determine the setting. Not all have 9detents.

Refer to Figure 31

The adjustable brush provides additional flexibility toaccommodate a wide range of seed sizes. Use leverto gently rotate the brush into position.

The settings range from 1 to 5 with detents at each halfstep, for a total of 9 detents. The factory default setting is21⁄2. Although the numbers are molded into the meterhousing, only “1” and “5” may be visible. To ensure con-sistency, rotate the lever fully counter-clockwise (1),and count detents as you advance it to the desired set-ting.

Use the general guidelines in the table below to adjustthe brush position to your seed size and shape. Thenumbers listed correspond to the numbers printed on theouter housing of your meter.

If there is a decal on your meter, its units are in poundsper 80,000 seed bag. The table below includes seedsper pound.

Figure 31Finger Meter Brush Lever

25276

5

1

43

2

L

L

LBag Weight

(80,000 seeds)Seeds Per

PoundBrushSetting

Rounds

65 lbs 1230 or less 1

65 to 55 lbs 1230 to 1450 2

55 to 45 lbs 1450 to 1780 3

45 to 35 lbs 1780 to 2300 4

35 lbs 2300 or more 5

Flats

45 lbs 1780 or less 1

45 to 35 lbs 1780 to 2300 2

35 lbs 2300 or more 3

401-347B 08/02/2010


Finger Meter InsertsRefer to Figure 32

The backing plate is equipped with an “A” insert . Intests, this insert provides the best performance in mostseed sizes. However, there are two alternative insertsthat can be used. Before changing to a different insert,please consult with a Great Plains service representa-tive for a recommendation.

The identification of the insert type is molded into theback of the insert.

Be cautious in using seed treatments, additives, and otherchemicals when possible. They can cause meter performanceproblems and premature wear to meter parts. See “SeedLubricants” on page 60.

Always store meters in a dry, secure place, with brush inbetween two meter fingers. Moisture, temperature, nest-build-ing insects and rodents can create problems.

Always pay attention to your seed monitor and operatingmanual. Monitor the amount of seed you are planting com-pared to your expectations. Always investigate abnormalities!

Figure 32Finger Meter Insert

22908

1

08/02/2010 401-347B




Great Plains always recommends test stand calibration of the finger meter to the population and ground speed desired .

For Round Corn optimum meter speed is 45 to 75 RPM For Flat Corn optimum meter speed is 60 to 75 RPM( Shaded & Non-shaded areas ) (Shaded area)

Range Driving = 30Sprockets Driven = 20 Ground Speed

Transmission Seed Seed 7 mph 6.5 mph 6 mph 5.5 mph 5 mph 4.5 mph 4 mph 3.5 mphCombinations Population Spacing Meter Meter Meter Meter Meter Meter Meter Meter

Driving Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm)17 28 15 115 20.7 59 55 51 4717 27 15 675 20.0 62 57 53 4817 26 16 278 19.3 64 59 55 50 46 Not Recommended19 28 16 894 18.6 66 62 57 52 4717 25 16 929 18.5 67 62 57 52 4819 27 17 519 17.9 69 64 59 54 4917 24 17 635 17.8 69 64 59 54 49 4519 26 18 193 17.2 71 66 61 56 51 4617 23 18 401 17.0 72 67 62 57 52 4619 25 18 921 16.6 74 69 64 58 53 4819 24 19 709 15.9 72 66 61 55 5023 28 20 450 15.3 75 69 63 57 52 4619 23 20 566 15.2 75 69 63 58 52 4623 27 21 208 14.8 71 65 60 54 4824 28 21 339 14.7 72 66 60 54 4823 26 22 023 14.2 74 68 62 56 4924 27 22 130 14.2 75 68 62 56 5025 28 22 228 14.1 75 69 62 56 5017 19 22 275 14.1 75 69 63 56 5023 25 22 904 13.7 71 64 58 51 4524 26 22 981 13.6 71 64 58 52 4525 27 23 052 13.6 71 65 58 52 4526 28 23 118 13.6 71 65 58 52 4523 24 23 859 13.1 74 67 60 54 4724 25 23 900 13.1 74 67 60 54 4725 26 23 938 13.1 74 67 60 54 4726 27 23 974 13.1 74 67 61 54 4727 28 24 007 13.1 74 67 61 54 4723 23 24 896 12.6 70 63 56 4928 27 25 818 12.1 72 65 58 5127 26 25 853 12.1 73 65 58 5126 25 25 892 12.1 73 65 58 5125 24 25 933 12.1 73 65 58 5124 23 25 978 12.1 73 66 58 5128 26 26 811 11.7 75 68 60 5327 25 26 888 11.7 75 68 60 5326 24 26 971 11.6 68 61 5325 23 27 061 11.6 68 61 5319 17 27 825 11.3 70 62 5528 25 27 883 11.2 70 63 5527 24 28 008 11.2 Not Recommended 71 63 5526 23 28 143 11.1 71 63 5528 24 29 045 10.8 73 65 5727 23 29 226 10.7 74 66 5723 19 30 137 10.4 68 5928 23 30 308 10.3 68 6024 19 31 447 10.0 71 6225 19 32 758 9.6 74 6423 17 33 683 9.3 6626 19 34 068 9.2 6724 17 35 147 8.9 6927 19 35 378 8.9 6925 17 36 612 8.6 7228 19 36 689 8.5 7226 17 38 076 8.2 7527 17 39 540 7.928 17 41 005 7.6

31201

401-347B 08/02/2010








Driving Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm)17 28 20 154 15.617 27 20 900 15.017 26 21 704 14.519 28 22 525 13.917 25 22 572 13.919 27 23 359 13.4 4617 24 23 513 13.3 4619 26 24 257 12.9 4817 23 24 535 12.8 48 4519 25 25 228 12.4 50 4619 24 26 279 11.9 52 4823 28 27 267 11.5 54 50 46 Not Recommended19 23 27 422 11.4 54 50 4623 27 28 277 11.1 56 52 4824 28 28 452 11.0 56 52 4823 26 29 364 10.7 58 54 49 4524 27 29 506 10.6 58 54 50 4625 28 29 638 10.6 58 54 50 4617 19 29 700 10.6 58 54 50 4623 25 30 539 10.3 60 56 51 4724 26 30 641 10.2 60 56 52 4725 27 30 736 10.2 60 56 52 4726 28 30 823 10.2 61 56 52 4823 24 31 811 9.9 62 58 54 49 4524 25 31 867 9.8 63 58 54 49 4525 26 31 918 9.8 63 58 54 49 4526 27 31 965 9.8 63 58 54 49 4527 28 32 009 9.8 63 58 54 49 4523 23 33 194 9.4 65 61 56 51 4728 27 34 424 9.1 68 63 58 53 4827 26 34 471 9.1 68 63 58 53 4826 25 34 522 9.1 68 63 58 53 4825 24 34 578 9.1 68 63 58 53 4924 23 34 638 9.1 68 63 58 53 4928 26 35 748 8.8 70 65 60 55 50 4527 25 35 850 8.7 70 65 60 55 50 4526 24 35 961 8.7 71 66 61 55 50 4525 23 36 081 8.7 71 66 61 56 51 4619 17 37 100 8.5 73 68 62 57 52 4728 25 37 178 8.4 73 68 63 57 52 4727 24 37 344 8.4 73 68 63 58 52 4726 23 37 524 8.4 74 68 63 58 53 4728 24 38 727 8.1 71 65 60 54 4927 23 38 967 8.0 71 66 60 55 4923 19 40 183 7.8 73 68 62 56 51 4528 23 40 411 7.8 74 68 62 57 51 4524 19 41 930 7.5 71 65 59 53 4725 19 43 677 7.2 74 67 61 55 4923 17 44 910 7.0 69 63 57 5026 19 45 424 6.9 70 64 57 51 4524 17 46 863 6.7 72 66 59 53 4627 19 47 171 6.6 73 66 60 53 4625 17 48 815 6.4 75 68 62 55 4828 19 48 918 6.4 Not Recommended 75 69 62 55 4826 17 50 768 6.2 71 64 57 5027 17 52 721 5.9 74 67 59 5228 17 54 673 5.7 69 61 54

31202

08/02/2010 401-347B


YP 1225 - 1625 Twin Row 30in Low Range

6 Finger MeterATTENTION ! ! ! (For all seed corn types)





Driving Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm)17 28 13 436 31.1

17 27 13 933 30.0

17 26 14 469 28.9

19 28 15 017 27.8

17 25 15 048 27.8

19 27 15 573 26.9 4617 24 15 675 26.7 4619 26 16 172 25.9 4817 23 16 357 25.6 48 4519 25 16 819 24.9 50 4619 24 17 519 23.9 52 4823 28 18 178 23.0 54 50 46 Not Recommended19 23 18 281 22.9 54 50 4623 27 18 851 22.2 56 52 4824 28 18 968 22.0 56 52 4823 26 19 576 21.4 58 54 49 4524 27 19 671 21.3 58 54 50 4625 28 19 759 21.2 58 54 50 4617 19 19 800 21.1 58 54 50 4623 25 20 359 20.5 60 56 51 4724 26 20 427 20.5 60 56 52 4725 27 20 490 20.4 60 56 52 4726 28 20 549 20.4 61 56 52 4823 24 21 208 19.7 62 58 54 49 4524 25 21 244 19.7 63 58 54 49 4525 26 21 279 19.7 63 58 54 49 4526 27 21 310 19.6 63 58 54 49 4527 28 21 339 19.6 63 58 54 49 4523 23 22 130 18.9 65 61 56 51 4728 27 22 949 18.2 68 63 58 53 4827 26 22 981 18.2 68 63 58 53 4826 25 23 015 18.2 68 63 58 53 4825 24 23 052 18.1 68 63 58 53 4924 23 23 092 18.1 68 63 58 53 4928 26 23 832 17.5 70 65 60 55 50 4527 25 23 900 17.5 70 65 60 55 50 4526 24 23 974 17.4 71 66 61 55 50 4525 23 24 054 17.4 71 66 61 56 51 4619 17 24 733 16.9 73 68 62 57 52 4728 25 24 785 16.9 73 68 63 57 52 4727 24 24 896 16.8 73 68 63 58 52 4726 23 25 016 16.7 74 68 63 58 53 4728 24 25 818 16.2 76 71 65 60 54 4927 23 25 978 16.1 77 71 66 60 55 4923 19 26 789 15.6 79 73 68 62 56 51 4528 23 26 940 15.5 79 74 68 62 57 51 4524 19 27 953 15.0 82 76 71 65 59 53 4725 19 29 118 14.4 80 74 67 61 55 4923 17 29 940 14.0 82 76 69 63 57 5026 19 30 283 13.8 83 76 70 64 57 51 4524 17 31 242 13.4 85 79 72 66 59 53 4627 19 31 447 13.3 79 73 66 60 53 4625 17 32 544 12.8 82 75 68 62 55 4828 19 32 612 12.8 82 75 69 62 55 4826 17 33 845 12.4 85 78 71 64 57 5027 17 35 147 11.9 Not Recommended 81 74 67 59 5228 17 36 449 11.5 84 77 69 61 54

31203

401-347B 08/02/2010


YP 1225 - 1625 Twin Row 30in High Range






Driving Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm)17 28 20 154 20.7 59 55 51 4717 27 20 900 20.0 62 57 53 4817 26 21 704 19.3 64 59 55 50 4619 28 22 525 18.6 66 62 57 52 47 Not Recommended17 25 22 572 18.5 67 62 57 52 4819 27 23 359 17.9 69 64 59 54 4917 24 23 513 17.8 69 64 59 54 49 4519 26 24 257 17.2 71 66 61 56 51 4617 23 24 535 17.0 72 67 62 57 52 4619 25 25 228 16.6 74 69 64 58 53 4819 24 26 279 15.9 77 72 66 61 55 5023 28 27 267 15.3 80 75 69 63 57 52 4619 23 27 422 15.2 81 75 69 63 58 52 4623 27 28 277 14.8 83 77 71 65 60 54 4824 28 28 452 14.7 84 78 72 66 60 54 4823 26 29 364 14.2 80 74 68 62 56 4924 27 29 506 14.2 81 75 68 62 56 5025 28 29 638 14.1 81 75 69 62 56 5017 19 29 700 14.1 81 75 69 63 56 5023 25 30 539 13.7 84 77 71 64 58 51 4524 26 30 641 13.6 84 77 71 64 58 52 4525 27 30 736 13.6 84 78 71 65 58 52 4526 28 30 823 13.6 84 78 71 65 58 52 4523 24 31 811 13.1 80 74 67 60 54 4724 25 31 867 13.1 80 74 67 60 54 4725 26 31 918 13.1 81 74 67 60 54 4726 27 31 965 13.1 81 74 67 61 54 4727 28 32 009 13.1 81 74 67 61 54 4723 23 33 194 12.6 84 77 70 63 56 4928 27 34 424 12.1 80 72 65 58 5127 26 34 471 12.1 80 73 65 58 5126 25 34 522 12.1 80 73 65 58 5125 24 34 578 12.1 80 73 65 58 5124 23 34 638 12.1 80 73 66 58 5128 26 35 748 11.7 83 75 68 60 5327 25 35 850 11.7 83 75 68 60 5326 24 35 961 11.6 83 76 68 61 5325 23 36 081 11.6 84 76 68 61 5319 17 37 100 11.3 78 70 62 5528 25 37 178 11.2 78 70 63 5527 24 37 344 11.2 79 71 63 5526 23 37 524 11.1 79 71 63 5528 24 38 727 10.8 81 73 65 5727 23 38 967 10.7 82 74 66 5723 19 40 183 10.4 85 76 68 5928 23 40 411 10.3 85 77 68 6024 19 41 930 10.0 79 71 6225 19 43 677 9.6 83 74 6423 17 44 910 9.3 Not Recommended 85 76 6626 19 45 424 9.2 76 6724 17 46 863 8.9 79 6927 19 47 171 8.9 79 6925 17 48 815 8.6 82 7228 19 48 918 8.5 82 7226 17 50 768 8.2 85 7527 17 52 721 7.9 7828 17 54 673 7.6 81

31204

08/02/2010 401-347B


YP 1225 - 1625 Twin Row 30in High Range







17 27 20 900 20.0

17 26 21 704 19.3

19 28 22 525 18.6

17 25 22 572 18.5

19 27 23 359 17.9

17 24 23 513 17.8

19 26 24 257 17.2

17 23 24 535 17.0

19 25 25 228 16.6

19 24 26 279 15.9

23 28 27 267 15.3

19 23 27 422 15.2

23 27 28 277 14.8

24 28 28 452 14.7

23 26 29 364 14.2

24 27 29 506 14.2

25 28 29 638 14.1

17 19 29 700 14.1

23 25 30 539 13.7 45 Not Recommended24 26 30 641 13.6 4525 27 30 736 13.6 4526 28 30 823 13.6 4523 24 31 811 13.1 4724 25 31 867 13.1 4725 26 31 918 13.1 4726 27 31 965 13.1 4727 28 32 009 13.1 4723 23 33 194 12.6 49 4528 27 34 424 12.1 51 4727 26 34 471 12.1 51 4726 25 34 522 12.1 51 4725 24 34 578 12.1 51 4724 23 34 638 12.1 51 4728 26 35 748 11.7 53 49 4527 25 35 850 11.7 53 49 4526 24 35 961 11.6 53 49 4525 23 36 081 11.6 53 49 4619 17 37 100 11.3 55 51 4728 25 37 178 11.2 55 51 4727 24 37 344 11.2 55 51 4726 23 37 524 11.1 55 51 4728 24 38 727 10.8 57 53 49 4527 23 38 967 10.7 57 53 49 4523 19 40 183 10.4 59 55 51 4728 23 40 411 10.3 60 55 51 4724 19 41 930 10.0 62 57 53 4925 19 43 677 9.6 64 60 55 51 4623 17 44 910 9.3 66 61 57 52 4726 19 45 424 9.2 67 62 57 53 4824 17 46 863 8.9 69 64 59 54 4927 19 47 171 8.9 69 65 60 55 50 4525 17 48 815 8.6 72 67 62 56 51 4628 19 48 918 8.5 72 67 62 57 51 4626 17 50 768 8.2 75 69 64 59 53 4827 17 52 721 7.9 72 67 61 55 5028 17 54 673 7.6 75 69 63 58 52 46

31205

401-347B 08/02/2010


YP 1225 - 1625 30in Rows Low Range






Driving Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm)17 28 13 436 15.6 74 68 62 57 51 4517 27 13 933 15.0 70 65 59 53 4717 26 14 469 14.5 73 67 61 55 4919 28 15 017 13.9 70 63 57 5117 25 15 048 13.9 70 63 57 5119 27 15 573 13.4 72 66 59 52 4617 24 15 675 13.3 73 66 59 53 4619 26 16 172 12.9 75 68 61 54 4817 23 16 357 12.8 69 62 55 4819 25 16 819 12.4 71 64 57 5019 24 17 519 11.9 74 66 59 5223 28 18 178 11.5 69 61 5419 23 18 281 11.4 69 62 5423 27 18 851 11.1 71 63 5624 28 18 968 11.0 72 64 5623 26 19 576 10.7 74 66 5824 27 19 671 10.6 75 66 5825 28 19 759 10.6 75 67 5817 19 19 800 10.6 75 67 5823 25 20 359 10.3 69 6024 26 20 427 10.2 69 6025 27 20 490 10.2 69 6026 28 20 549 10.2 69 6123 24 21 208 9.9 71 6224 25 21 244 9.8 72 6325 26 21 279 9.8 72 6326 27 21 310 9.8 72 6327 28 21 339 9.8 72 6323 23 22 130 9.4 75 6528 27 22 949 9.1 6827 26 22 981 9.1 6826 25 23 015 9.1 6825 24 23 052 9.1 6824 23 23 092 9.1 Not Recommended 6828 26 23 832 8.8 7027 25 23 900 8.7 7026 24 23 974 8.7 7125 23 24 054 8.7 7119 17 24 733 8.5 7328 25 24 785 8.4 7327 24 24 896 8.4 7326 23 25 016 8.4 7428 24 25 818 8.1

27 23 25 978 8.0

23 19 26 789 7.8

28 23 26 940 7.8

24 19 27 953 7.5

25 19 29 118 7.2

23 17 29 940 7.0

26 19 30 283 6.9

24 17 31 242 6.7

27 19 31 447 6.6

25 17 32 544 6.4

28 19 32 612 6.4

26 17 33 845 6.2

27 17 35 147 5.9

28 17 36 449 5.7 31206

08/02/2010 401-347B


YP 1225 - 1625 30in Rows Low Range







17 27 13 933 15.0

17 26 14 469 14.5

19 28 15 017 13.9

17 25 15 048 13.9

19 27 15 573 13.4 4617 24 15 675 13.3 4619 26 16 172 12.9 4817 23 16 357 12.8 48 45 Not Recommended19 25 16 819 12.4 50 4619 24 17 519 11.9 52 4823 28 18 178 11.5 54 50 4619 23 18 281 11.4 54 50 4623 27 18 851 11.1 56 52 4824 28 18 968 11.0 56 52 4823 26 19 576 10.7 58 54 49 4524 27 19 671 10.6 58 54 50 4625 28 19 759 10.6 58 54 50 4617 19 19 800 10.6 58 54 50 4623 25 20 359 10.3 60 56 51 4724 26 20 427 10.2 60 56 52 4725 27 20 490 10.2 60 56 52 4726 28 20 549 10.2 61 56 52 4823 24 21 208 9.9 62 58 54 49 4524 25 21 244 9.8 63 58 54 49 4525 26 21 279 9.8 63 58 54 49 4526 27 21 310 9.8 63 58 54 49 4527 28 21 339 9.8 63 58 54 49 4523 23 22 130 9.4 65 61 56 51 4728 27 22 949 9.1 68 63 58 53 4827 26 22 981 9.1 68 63 58 53 4826 25 23 015 9.1 68 63 58 53 4825 24 23 052 9.1 68 63 58 53 4924 23 23 092 9.1 68 63 58 53 4928 26 23 832 8.8 70 65 60 55 50 4527 25 23 900 8.7 70 65 60 55 50 4526 24 23 974 8.7 71 66 61 55 50 4525 23 24 054 8.7 71 66 61 56 51 4619 17 24 733 8.5 73 68 62 57 52 4728 25 24 785 8.4 73 68 63 57 52 4727 24 24 896 8.4 73 68 63 58 52 4726 23 25 016 8.4 74 68 63 58 53 4728 24 25 818 8.1 71 65 60 54 4927 23 25 978 8.0 71 66 60 55 4923 19 26 789 7.8 73 68 62 56 51 4528 23 26 940 7.8 74 68 62 57 51 4524 19 27 953 7.5 71 65 59 53 4725 19 29 118 7.2 74 67 61 55 4923 17 29 940 7.0 69 63 57 5026 19 30 283 6.9 70 64 57 51 4524 17 31 242 6.7 72 66 59 53 4627 19 31 447 6.6 73 66 60 53 4625 17 32 544 6.4 75 68 62 55 4828 19 32 612 6.4 75 69 62 55 4826 17 33 845 6.2 Not Recommended 71 64 57 5027 17 35 147 5.9 74 67 59 5228 17 36 449 5.7 69 61 54

31207

401-347B 08/02/2010


YP 1225 - 1625 30in Rows High Range






Driving Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm)17 28 20 154 10.4 59 55 51 4717 27 20 900 10.0 62 57 53 4817 26 21 704 9.6 64 59 55 50 4619 28 22 525 9.3 66 62 57 52 47 Not Recommended17 25 22 572 9.3 67 62 57 52 4819 27 23 359 9.0 69 64 59 54 4917 24 23 513 8.9 69 64 59 54 49 4519 26 24 257 8.6 71 66 61 56 51 4617 23 24 535 8.5 72 67 62 57 52 4619 25 25 228 8.3 74 69 64 58 53 4819 24 26 279 8.0 72 66 61 55 5023 28 27 267 7.7 75 69 63 57 52 4619 23 27 422 7.6 75 69 63 58 52 4623 27 28 277 7.4 71 65 60 54 4824 28 28 452 7.3 72 66 60 54 4823 26 29 364 7.1 74 68 62 56 4924 27 29 506 7.1 75 68 62 56 5025 28 29 638 7.1 75 69 62 56 5017 19 29 700 7.0 75 69 63 56 5023 25 30 539 6.8 71 64 58 51 4524 26 30 641 6.8 71 64 58 52 4525 27 30 736 6.8 71 65 58 52 4526 28 30 823 6.8 71 65 58 52 4523 24 31 811 6.6 74 67 60 54 4724 25 31 867 6.6 74 67 60 54 4725 26 31 918 6.6 74 67 60 54 4726 27 31 965 6.5 74 67 61 54 4727 28 32 009 6.5 74 67 61 54 4723 23 33 194 6.3 70 63 56 4928 27 34 424 6.1 72 65 58 5127 26 34 471 6.1 73 65 58 5126 25 34 522 6.1 73 65 58 5125 24 34 578 6.0 73 65 58 5124 23 34 638 6.0 73 66 58 5128 26 35 748 5.8 75 68 60 5327 25 35 850 5.8 75 68 60 5326 24 35 961 5.8 68 61 5325 23 36 081 5.8 68 61 5319 17 37 100 5.6 70 62 5528 25 37 178 5.6 70 63 5527 24 37 344 5.6 71 63 5526 23 37 524 5.6 71 63 5528 24 38 727 5.4 73 65 5727 23 38 967 5.4 74 66 5723 19 40 183 5.2 68 5928 23 40 411 5.2 68 6024 19 41 930 5.0 Not Recommended 71 6225 19 43 677 4.8 74 6423 17 44 910 4.7 6626 19 45 424 4.6 6724 17 46 863 4.5 6927 19 47 171 4.4 6925 17 48 815 4.3 7228 19 48 918 4.3 7226 17 50 768 4.1 7527 17 52 721 4.0

28 17 54 673 3.8 31208

08/02/2010 401-347B


YP 1225 - 1625 Twin Row 36in6 Finger Meter






Driving Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm)17 28 18 661 18.7 66 61 57 52 4717 27 19 352 18.0 68 64 59 54 4917 26 20 096 17.3 71 66 61 56 51 4619 28 20 856 16.7 74 68 63 58 53 4717 25 20 900 16.7 74 69 63 58 53 4819 27 21 629 16.1 76 71 66 60 55 4917 24 21 771 16.0 77 71 66 60 55 4919 26 22 461 15.5 79 74 68 62 57 51 4517 23 22 718 15.3 80 75 69 63 57 52 4619 25 23 359 14.9 83 77 71 65 59 53 4719 24 24 332 14.3 80 74 68 61 55 4923 28 25 247 13.8 83 77 70 64 57 51 4519 23 25 390 13.7 83 77 71 64 58 51 4523 27 26 182 13.3 79 73 66 60 53 4624 28 26 345 13.2 80 73 67 60 53 4723 26 27 189 12.8 82 76 69 62 55 4824 27 27 321 12.8 83 76 69 62 55 4825 28 27 443 12.7 83 76 69 62 55 4917 19 27 500 12.7 83 76 69 63 56 4923 25 28 277 12.3 79 71 64 57 5024 26 28 371 12.3 79 72 64 57 5025 27 28 459 12.2 79 72 65 57 5026 28 28 540 12.2 79 72 65 58 5023 24 29 455 11.8 82 74 67 60 5224 25 29 506 11.8 82 75 67 60 5225 26 29 553 11.8 82 75 67 60 5226 27 29 597 11.8 82 75 67 60 5227 28 29 638 11.8 82 75 67 60 5223 23 30 736 11.3 85 78 70 62 5428 27 31 874 10.9 80 72 64 5627 26 31 918 10.9 81 73 64 5626 25 31 965 10.9 81 73 65 5725 24 32 016 10.9 81 73 65 5724 23 32 072 10.9 81 73 65 5728 26 33 100 10.5 84 75 67 5927 25 33 194 10.5 84 75 67 5926 24 33 297 10.5 84 76 67 5925 23 33 408 10.4 84 76 67 5919 17 34 352 10.1 78 69 6128 25 34 424 10.1 78 70 6127 24 34 578 10.1 79 70 6126 23 34 745 10.0 79 70 6128 24 35 858 9.7 81 72 6327 23 36 081 9.7 82 73 6423 19 37 206 9.4 85 75 6628 23 37 417 9.3 85 76 6624 19 38 824 9.0 Not Recommended 78 6925 19 40 442 8.6 82 7123 17 41 583 8.4 84 7426 19 42 059 8.3 85 7424 17 43 391 8.0 7727 19 43 677 8.0 7725 17 45 199 7.7 8028 19 45 295 7.7 8026 17 47 007 7.4 8327 17 48 815 7.1

28 17 50 623 6.9 31209

401-347B 08/02/2010


YP 1225 - 1625 Twin Row 36in12 Finger Meter







17 27 25 803 13.5 4617 26 26 795 13.0 4719 28 27 808 12.5 49 4617 25 27 867 12.5 49 4619 27 28 838 12.1 51 4717 24 29 028 12.0 51 4819 26 29 948 11.6 53 49 45 Not Recommended17 23 30 290 11.5 54 50 4619 25 31 145 11.2 55 51 4719 24 32 443 10.7 57 53 49 4523 28 33 663 10.4 60 55 51 4719 23 33 854 10.3 60 56 51 4723 27 34 910 10.0 62 57 53 4824 28 35 126 9.9 62 58 53 4923 26 36 252 9.6 64 60 55 50 4624 27 36 427 9.6 64 60 55 51 4625 28 36 590 9.5 65 60 55 51 4617 19 36 667 9.5 65 60 56 51 4623 25 37 702 9.2 67 62 57 52 4824 26 37 828 9.2 67 62 57 53 4825 27 37 945 9.2 67 62 57 53 4826 28 38 054 9.2 67 62 58 53 4823 24 39 273 8.9 69 64 60 55 50 4524 25 39 342 8.9 70 65 60 55 50 4525 26 39 405 8.8 70 65 60 55 50 4526 27 39 463 8.8 70 65 60 55 50 4527 28 39 517 8.8 70 65 60 55 50 4523 23 40 981 8.5 72 67 62 57 52 4728 27 42 499 8.2 75 70 64 59 54 4827 26 42 557 8.2 75 70 64 59 54 4826 25 42 620 8.2 75 70 65 59 54 4825 24 42 688 8.2 75 70 65 59 54 4924 23 42 763 8.1 70 65 59 54 4928 26 44 133 7.9 72 67 61 56 50 4527 25 44 259 7.9 73 67 61 56 50 4526 24 44 396 7.8 73 67 62 56 50 4525 23 44 544 7.8 73 67 62 56 51 4519 17 45 802 7.6 75 69 64 58 52 4628 25 45 899 7.6 75 70 64 58 52 4627 24 46 103 7.6 70 64 58 52 4726 23 46 326 7.5 70 64 58 53 4728 24 47 811 7.3 72 66 60 54 4827 23 48 108 7.2 73 67 61 55 4923 19 49 608 7.0 75 69 63 56 5028 23 49 890 7.0 69 63 57 5024 19 51 765 6.7 72 65 59 52 4625 19 53 922 6.5 75 68 61 54 4823 17 55 445 6.3 70 63 56 4926 19 56 079 6.2 71 64 57 5024 17 57 855 6.0 73 66 58 5127 19 58 236 6.0 74 66 59 5125 17 60 266 5.8 Not Recommended 68 61 5328 19 60 393 5.8 69 61 5326 17 62 677 5.6 71 63 5527 17 65 087 5.4 74 66 5828 17 67 498 5.2 68 60

31210

08/02/2010 401-347B








Driving Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm)17 28 9 330 18.7 66 61 57 52 4717 27 9 676 18.0 68 64 59 54 4917 26 10 048 17.3 71 66 61 56 51 4619 28 10 428 16.7 74 68 63 58 53 4717 25 10 450 16.7 74 69 63 58 53 4819 27 10 814 16.1 71 66 60 55 4917 24 10 886 16.0 71 66 60 55 4919 26 11 230 15.5 74 68 62 57 51 4517 23 11 359 15.3 75 69 63 57 52 4619 25 11 680 14.9 71 65 59 53 4719 24 12 166 14.3 74 68 61 55 4923 28 12 624 13.8 70 64 57 51 4519 23 12 695 13.7 71 64 58 51 4523 27 13 091 13.3 73 66 60 53 4624 28 13 172 13.2 73 67 60 53 4723 26 13 595 12.8 69 62 55 4824 27 13 660 12.8 69 62 55 4825 28 13 721 12.7 69 62 55 4917 19 13 750 12.7 69 63 56 4923 25 14 138 12.3 71 64 57 5024 26 14 186 12.3 72 64 57 5025 27 14 229 12.2 72 65 57 5026 28 14 270 12.2 72 65 58 5023 24 14 727 11.8 74 67 60 5224 25 14 753 11.8 75 67 60 5225 26 14 777 11.8 75 67 60 5226 27 14 799 11.8 75 67 60 5227 28 14 819 11.8 75 67 60 5223 23 15 368 11.3 70 62 5428 27 15 937 10.9 72 64 5627 26 15 959 10.9 73 64 5626 25 15 983 10.9 73 65 5725 24 16 008 10.9 73 65 5724 23 16 036 10.9 73 65 5728 26 16 550 10.5 75 67 5927 25 16 597 10.5 75 67 5926 24 16 648 10.5 67 5925 23 16 704 10.4 67 5919 17 17 176 10.1 69 6128 25 17 212 10.1 70 6127 24 17 289 10.1 70 6126 23 17 372 10.0 70 6128 24 17 929 9.7 72 6327 23 18 040 9.7 73 6423 19 18 603 9.4 75 6628 23 18 709 9.3 6624 19 19 412 9.0 Not Recommended 6925 19 20 221 8.6 7123 17 20 792 8.4 7426 19 21 030 8.3 7424 17 21 696 8.0

27 19 21 838 8.0

25 17 22 600 7.7

28 19 22 647 7.7

26 17 23 504 7.4

27 17 24 408 7.1

28 17 25 312 6.9 31211

401-347B 08/02/2010








Driving Driven (seeds/acre) (inches) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm) (rpm)17 28 18 661 9.3 66 61 57 52 4717 27 19 352 9.0 68 64 59 54 4917 26 20 096 8.7 71 66 61 56 51 4619 28 20 856 8.4 74 68 63 58 53 4717 25 20 900 8.3 74 69 63 58 53 4819 27 21 629 8.1 71 66 60 55 4917 24 21 771 8.0 71 66 60 55 4919 26 22 461 7.8 74 68 62 57 51 4517 23 22 718 7.7 75 69 63 57 52 4619 25 23 359 7.5 71 65 59 53 4719 24 24 332 7.2 74 68 61 55 4923 28 25 247 6.9 70 64 57 51 4519 23 25 390 6.9 71 64 58 51 4523 27 26 182 6.7 73 66 60 53 4624 28 26 345 6.6 73 67 60 53 4723 26 27 189 6.4 69 62 55 4824 27 27 321 6.4 69 62 55 4825 28 27 443 6.3 69 62 55 4917 19 27 500 6.3 69 63 56 4923 25 28 277 6.2 71 64 57 5024 26 28 371 6.1 72 64 57 5025 27 28 459 6.1 72 65 57 5026 28 28 540 6.1 72 65 58 5023 24 29 455 5.9 74 67 60 5224 25 29 506 5.9 75 67 60 5225 26 29 553 5.9 75 67 60 5226 27 29 597 5.9 75 67 60 5227 28 29 638 5.9 75 67 60 5223 23 30 736 5.7 70 62 5428 27 31 874 5.5 72 64 5627 26 31 918 5.5 73 64 5626 25 31 965 5.5 73 65 5725 24 32 016 5.4 73 65 5724 23 32 072 5.4 73 65 5728 26 33 100 5.3 75 67 5927 25 33 194 5.2 75 67 5926 24 33 297 5.2 67 5925 23 33 408 5.2 67 5919 17 34 352 5.1 69 6128 25 34 424 5.1 70 6127 24 34 578 5.0 70 6126 23 34 745 5.0 70 6128 24 35 858 4.9 72 6327 23 36 081 4.8 73 6423 19 37 206 4.7 75 6628 23 37 417 4.7 6624 19 38 824 4.5 Not Recommended 6925 19 40 442 4.3 7123 17 41 583 4.2 7426 19 42 059 4.1 7424 17 43 391 4.0

27 19 43 677 4.0

25 17 45 199 3.9

28 19 45 295 3.8

26 17 47 007 3.7

27 17 48 815 3.6

28 17 50 623 3.4 31212

08/02/2010 401-347B


Sprocket Indexing (Stagger)

This chapter applies to both ground and hydraulic drive,but only with finger meters.

If you are planting:• finger-metered,• twin-row crops,• at seed interval spacings above 61⁄2 inches,you can synchronize each pair of adjacent meters in atwin row so that you achieve the maximum seed-to-seed spacing between the units of the pair.

If you are planting any of:- single-row,- or with singulating meters,- or a volumetric crop,- or twin row with seed spacings below 61⁄2in,this section of the manual, and the sprocket indexingcharts, do not apply to your operations.

If the initial indexing does not provide equal spacing,see “Indexing Fine Adjustment” on page 47.

Refer to Figure 33

1. Find the Indexing Chart for your row spacing, meterfinger count and desired seed population. Note the“Rear Meter Sprocket Tooth #” value in the farright column.

2. Remove both meters of a row unit pair. Note thattooth 1 and many of the other teeth on the drivensprockets , are stamped with a tooth number.

On front row unit:

3. Relax idlers on front meter drive by lifting thespring off the rear post .

4. Lift chain off driven sprocket , and rotate sprocketso that tooth 1 is as close as possible to straight up(top dead center).

5. Re-engage chain and idlers, making sure chain istaut at top, and that sprocket tooth 1 has not shiftedoff TDC.

On rear row unit:

6. Relax idlers on rear meter drive by lifting thespring off the rear post .

7. Lift chain off driven sprocket , and rotate sprocketso that the tooth number called for in the chart is atTDC (or is the same as the front row sprocket).

8. Re-engage chain and idlers, making sure chain istaut at top, and that the designated sprocket toothhas not shifted off TDC.

9. Re-install meters. No particular wheel orientation isrequired during meter installation. The meterengagement is symmetrical, and the results identi-cal no matter how the coupler captures the metershaft.

• •

• • •

• • •

• • •

Indexed - deliberate pair spacing provides maximum plant separation

Non-Indexed - arbitrary pair spacing

Figure 33Sprocket Indexing

25417

12 3

5

46

1 2

3

4

1

5

6

2

401-347B 08/02/2010


Sprocket Indexing Charts1. For: your 6- or 12-finger meter, and

your twin row spacing (30in on this page)find your seed rate in the Population column, or yourseed spacing in the Seed Spacing column. Seedspacing is seed-to-seed within a single row of a twinrow pair.

2. At the front/forward row unit of a pair, set the driven(final) sprocket of the meter drive so that toothstamped #1 is straight up (TDC, 12:00 position).

3. At the rear/trailing row unit of the pair, set the drivensprocket so that the tooth number at “Rear Meter” isin the straight up 12:00 position.

These are NOT seed rate or seed spacing charts. These arecharts for staggering seed spacing between the rows of a twinrow.

Note: For adjusting spacing between rows of the pair,see “Indexing Fine Adjustment” on page 47.

Verify the 12:00 sprocket tooth position with the top length ofchain taut.

30in Twin Row Sprocket Indexing

6 Finger Meter Twin Row Sprocket Indexing30in Twin Row

Population Single RowSeeds per Seed Front Rear

Acre Spacing (in) Meter Meter

15,700 to 17,300 24.2 to 26.6 1 417,300 to 18,800 22.2 to 24.2 1 718,800 to 20,400 20.5 to 22.2 1 1020,400 to 22,000 19.0 to 20.5 1 1322,000 to 23,600 17.7 to 19.0 1 1623,600 to 25,000 16.7 to 17.7 1 1925,000 to 26,600 15.7 to 16.7 1 326,600 to 28,300 14.8 to 15.7 1 628,300 to 29,900 14.0 to 14.8 1 929,900 to 31,500 13.3 to 14.0 1 1231,500 to 33,000 12.7 to 13.3 1 1533,000 to 34,700 12.1 to 12.7 1 1834,700 to 36,200 11.6 to 12.1 1 236,200 to 37,800 11.1 to 11.6 1 537,800 to 39,300 10.6 to 11.1 1 839,300 to 40,800 10.3 to 10.6 1 1140,800 to 42,500 9.8 to 10.3 1 1442,500 to 44,000 9.5 to 9.8 1 1744,000 to 45,400 9.2 to 9.5 1 145,400 to 47,000 8.9 to 9.2 1 447,000 to 48,600 8.6 to 8.9 1 748,600 to 50,400 8.3 to 8.6 1 1050,400 to 51,800 8.1 to 8.3 1 1351,800 to 53,300 7.8 to 8.1 1 16

Set Sprocket to Tooth Number on ..






08/02/2010 401-347B


36in Twin Row Sprocket Indexing

These are NOT seed rate or seed spacing charts. These arecharts for staggering seed spacing between the rows of a twinrow.

Note: For adjusting spacing between rows of the pair,see “Indexing Fine Adjustment” on page 47.

Verify the 12:00 sprocket tooth position with the top length ofchain taut.











401-347B 08/02/2010


Indexing Fine AdjustmentIf, after indexing, twin-row side-to-side seed stagger issubstantially imbalanced, it is possible to make smalladjustments that may correct it.

The procedure is different for 6- and 12-finger meters.

If an adjustment is made, test it on one row pair beforeadjusting the entire planter.

Before making any Indexing Adjustments:

• Check actual planted seed spacing. Seed Spacing isfound by measuring the distance between 25 correctlyplanted seeds in one row and dividing by 24. (A visibleskip or double is counted as one seed.)

• Make sure current rear sprocket index numbermatches the number in the indexing chart for actualseed spacing being planted.

6-Finger Meter Stagger Adjustment(any tire)

Find your current indexing value row in the charts.

In the Indexing Chart, each (sprocket tooth) numberdirectly above or below the current rear meter sprocketsetting, in the right most column, represents a smallmovement of the rear row seed relative to the front rowseed.

Changing rear your sprocket to the next number up inthe chart retards, moving each rear row seed back asmall amount.

Changing rear sprocket to the next number down in thechart advances, moving each rear row seed ahead asmall amount.

Example 1: The 6 Finger (Twin Row 30in) planting popu-lation is 29900 or 14in seed spacing. The chart settingfor the rear sprocket is (15). Each rear row seed shouldfall 7in behind the front row seed.

If each rear row seed measures only 6in behind the frontrow seed, reset the rear meter sprocket to the next num-ber up in the chart (12). This will move the rear seedsback to make the stagger closer to 7in.

Example 2: The 6 Finger (Twin Row 30in) planting popu-lation is 29900 or 14in seed spacing. The chart settingfor the rear sprocket is (15). Each rear row seed shouldfall 7in behind front row seed.

If each rear row seed measures 8in behind the front rowseed, reset the rear meter sprocket to the next numberdown in the chart (18). This will move the rear seedsahead to make the stagger closer to 7in.

••

•••

•••Desired seed stagger

Rear unit needs to be retarded

•

••••

•

•

•••

••••Rear unit needs to be advanced

Direction of Travel ☞

Seeds per Seed ront Rear


,700 to 17,300 24.2 to 26.6 1 4,300 to 18,800 22.2 to 24.2 1 7,800 to 20,400 20.5 to 22.2 1 10,400 to 22,000 19.0 to 20.5 1 13,000 to 23,600 17.7 to 19.0 1 16,600 to 25,000 16.7 to 17.7 1 19,000 to 26,600 15.7 to 16.7 1 3,600 to 28,300 14.8 to 15.7 1 6,300 to 29,900 14.0 to 14.8 1 9,900 to 31,500 13 3 to 14 0 1 12,500 to 33,000 12.7 to 13.3 1 15,000 to 34,700 12.1 to 12.7 1 18,700 to 36,200 11.6 to 12.1 1 2200 to 37 800 11 1 to 11 6 1 5

Advance

RetardCurrent

Figure 34: Portion ofSprocket Indexing Chart

08/02/2010 401-347B


12-Finger Meter Stagger Adjustment(any tire)

Before making any Indexing Adjustments, check actualplanted seed spacing. Seed Spacing is found by mea-suring the distance between 25 correctly planted seedsin one row and dividing by 24. (A visible skip or doubleshould be counted as one seed.) Make sure current rearsprocket index number matches the number in theindexing chart for actual seed spacing being planted.

Find your current indexing value row in the charts.

In the Indexing Charts, each (sprocket tooth) numberdirectly above or below the current rear meter sprocketsetting, in the right most column, represents a smallmovement of the rear row seed relative to the front rowseed.

Changing rear your sprocket to the next number down inthe chart retards, moving each rear row seed back asmall amount.

Changing rear sprocket to the next number up in thechart advances, moving each rear row seed ahead asmall amount.

Example 1: The 12 Finger (Twin Row 30in) planting pop-ulation is 34800 or 12in seed spacing. The chart settingfor the rear sprocket is (3). Each rear row seed should fall6in behind the front row seed.

If each rear row seed measures 7in behind the front rowseed, reset the rear meter sprocket to the next numberup in the chart (11). This will move the rear seeds aheadand make the stagger closer to 6in.

Example 2: The 12 Finger (Twin Row 30in) planting pop-ulation is 34800 or 12in seed spacing. The chart settingfor the rear sprocket is (3). Each rear row seed should fall6in behind the front row seed.

If each rear row seed measures 5in behind the front rowseed, reset the rear meter sprocket to the next numberdown in the chart (14). This will move the rear seedsback to make the stagger closer to 6in.

••

•••

•••Desired seed stagger

Rear unit needs to be retarded

•

••••

•

•

•••

••••Rear unit needs to be advanced

Direction of Travel ☞




26,600 to 28,300 14.8 to 15.7 1 1328,300 to 29,900 14.0 to 14.8 1 529,900 to 31,500 13.3 to 14.0 1 1631,500 to 33,000 12.7 to 13.3 1 833,000 to 34,700 12.1 to 12.7 1 1934,700 to 36,200 11.6 to 12.1 1 1136,200 to 37,800 11.1 to 11.6 1 337,800 to 39,300 10.6 to 11.1 1 1439,300 to 40,800 10.3 to 10.6 1 640,800 to 42,500 9.8 to 10.3 1 1742 500 to 44 000 9 5 to 9 8 1 9


Advance

RetardCurrent

Figure 35: Portion ofSprocket Indexing Chart

401-347B 08/02/2010


Fertilizer Rate

The YP1225 or YP1625 planter offers a fertilizer mani-fold, and may include a pair of ground-driven pumps ora single pump driven by the meter transfer shaft. Tanksare located on the seed cart.

Fertilizer rate is independent of seed rate. Basic fertil-izer rates are set by the pump systems. Detailed pumpoperations are described in the planter Operator’sManual.

The system includes orifice plates at each row unitdrop line. The system also includes a pressure reliefvalve and strainer, which can affect flow rate, and needto be considered when setting rates.

Adjust the relief valve(s) per the Operator’s Manual.

Orifice Plate SelectionRefer to Figure 36

Orifice plates at each drop line nozzle provide back-pressure that balances flow in the manifold, assuringthat each row obtains the same flow rate. Plates areprovided with the system in three sizes. Additionalsizes are available.

Plates are initially selected and installed based on theproposed flow rates. Due to various factors, includingmaterial viscosity and ambient temperature, actualfield flow rate may vary from the charts. It is importantto monitor actual material consumption rates, and itmay be necessary to change orifice size, and adjustpump settings, to obtain the desired field rate.

In general, the orifice needs to be small enough tocreate a minimum pressure in the manifold but largeenough to prevent the manifold pressure from exceed-ing the maximum:15psi min., 15-40 optimal, 65 psi max.

Wear protective gloves when changing orifice plates.

To reduce orifice plugging and pump wear, use thelargest orifice practical for your fertilizer applicationrate.

Orifice size is only used to create 15-65 PSI back pressure toprovide even flow between rows. Set application rate in gal-lons per acre using pump drive chart.

Figure 36Fertilizer Orifice Plate

29984

1

Suggested Orifice Size

15in,30in Twin

20inSingle

30inSingle

Gal

lon

s p

er A

cre

at 5

MP

H

2 20 20 28

3 20 28 34

4 28 28 34

5 28 28 48

6 34 34 48

7 34 34 48

8 34 48 59

9 34 48 59

10 48 48 59

11 48 48 59

12 48 48 59

1

1

Orifice Part Port PortSize Number Diameter Area20 832-052C 0.020 in 0.20 mm²28* 832-056C 0.028 in 0.40 mm²34* 832-053C 0.034 in 0.59 mm²48* 832-054C 0.048 in 1.17 mm²59 832-057C 0.059 in 1.76 mm²80 832-055C 0.080 in 3.24 mm²98 832-059C 0.098 in 4.87 mm²

29993* Sizes standard in many fertilizer bundles. Check your accessories before ordering.

08/02/2010 401-347B


Ground Drive Fertilizer RateOn new and upgraded planters, the pump is drivenby a ground contact wheel , and fertilizer rate is inde-pendent of seed rate. Fertilizer rate is set by sprocketson the ground drive assembly.

Refer to Figure 37

1. Check plumbing setup. See “Setting Relief Valve”on page 59.

2. Determine sprocket pair required from tables on fol-lowing pages. If this pair is already installed on driv-ing/driven shafts, no further adjustments arerequired. Otherwise, to change sprockets, continuewith step 3.

3. Remove knob and guard . Loosen idler , andremove chain from Upper (driven) pump shaftand Lower (driving) shaft .

4. Select the new driven sprocket from the storageshafts , . Remove the linch pin at shaft , andexchange sprockets. Store the previous sprocketon a storage shaft.

5. Select the new driving sprocket from the storageshafts , . Remove the linch pin at shaft , andexchange sprockets. Store the previous sprocket ona storage shaft.

6. Remount the chain , making sure open end of clipat removable link faces away from direction ofchain travel. Re-engage idler , tightening so thatthe longest span of the chain has 1⁄4in of slack.

Figure 37Ground Rate Adjustment

25319

1

4

3L

U

7

2

5

6

8

9

DRIVING

DRIVEN

1

2

3 4 5

6 U

L

7 8 U

7 8 L6

9

5

401-347B 08/02/2010


Fertilizer Rate: YP1225-1230, -1820, -24TR

08/02/2010 401-347B


Fertilizer Rate: YP1225-2315

401-347B 08/02/2010


Fertilizer Rate: YP1225-16TR36

08/02/2010 401-347B


Fert. Rate: YP1625-1630, -1670, -2420, 32TR

401-347B 08/02/2010


Fertilizer Rate: YP1625-3115

08/02/2010 401-347B


Fertilizer Rate: YP1625-1236, -24TR36

401-347B 08/02/2010


Shaft Drive Fertilizer RateApplies only to:YP1125 s/n A1064K- and YP1625 s/n A1032B-

On older planters, the pump is driven by the same wingdrive shaft as the seed meters, and fertilizer rate isaffected by seed rate sprocket changes. When fertilizerrate needs changing, or seed rate has changed, sprock-ets at the pump need to be changed to set or compen-sate.

Shaft Drive Type 1Refer to Figure 38

Note: Drive Type 1 uses one 17 or 23 tooth sprocket atthe pump and changes sprockets on the driving(clutch) shaft to adjust rate.

Figure 38Fertilizer Drive Type 1

23130

08/02/2010 401-347B


Shaft Drive Type 2Applies only to:YP1125 s/n A1064K- and YP1625 s/n A1032B-

Refer to Figure 39

Note: Drive type 2 uses one 23 or 30 tooth sprocket onthe driving (clutch) shaft and changes pumpsprockets to adjust rate.

Figure 39Fertilizer Drive Type 2

23131

401-347B 08/02/2010


Setting Relief ValveRefer to Figure 40

A relief valve is mounted directly above the pump to pro-tect the manifold and pump from excessive pressure.Any product that dumps over the relief valve will dis-charge from the dump line .

To set relief valve:

1. Unlock plastic jam nut from relief valve knob .

2. Unscrew knob clockwise until it loses contact withinternal spring.

3. Screw knob counterclockwise two turns. Start at thissetting.

4. Observe manifold gauge . Watch for relief valvedischarge while operating in the field.

5. If valve is dumping product and gauge reads under65 psi, stop tractor and, looking down, turn knobclockwise 1⁄4 turn. Continue operating at normal fieldspeed. Repeat this step as needed until no productis discharged from relief valve.

6. If pressure gauge reads above 65 psi, change to alarger orifice. Go to step 2. Repeat steps.

StrainerRefer to Figure 41

A Banjo brand strainer is supplied with the ground drivefertilizer pump. It is plumbed before the Hypro pump.The standard 80 mesh screen should be suitable formost applications. Other screen sizes are available fromBanjo Corporation.

Wear protective gloves when changing screens.

If changing screen sizes, keep in mind the following.

• A smaller mesh (100) will keep very small manifoldorifice plates from plugging so often. However, thescreen will have to be cleaned more often.

• A larger mesh (50) or (30) will pass more material butshould only be considered when using large manifoldorifice plates.

• A plugged or partially plugged screen will starve thepump resulting in a reduced application rate.

• Mesh sizes: (Smallest) 100, 80, 50, 30 (Largest)

Figure 40Pressure Relief Valve

22502

3

1

2

4

4

1 2

3

4

Figure 41Strainer

18418

11

08/02/2010 401-347B


Appendix

Seed Lubricants

Singulator Plus Meters (all seeds)

Ezee Glide Plus Talc-Graphite Mix

821-069C bucket, 5 gallon (19 liter)

Ezee Glide Plus LubricantTo maximize performance of Great Plains metering sys-tems, it is imperative to use only “Ezee Glide Plus” lubri-cant. “Ezee Glide Plus” Talc-Graphite lubricant ismandatory for all seeds, especially treated or inoculatedseed. Thorough mixing of seed and added lubricantis required.

Recommended usage:

For clean seeds other than milo and cotton sprinkleone cup of Ezee Glide Plus Talc per 4 bushels or units(170 ml per 100 liters) of seed.

For milo and cotton double the application toone cup (or more) per 2 bu or units (335 ml per 100liters) of seed.

Adjust this rate as necessary so all seeds becomecoated while avoiding an accumulation of lubricant inthe bottom of the hopper.

For seed with excessive treatment, or for humid plantingenvironments, increase the rate as needed for smoothmeter operation.

Irritation and Chronic Exposure Hazard:Wear gloves. DO NOT use hands or any part of your body tomix seed lubricant. Wear a respirator when transferring andmixing. Avoid breathing lubricant dust. Not an acute hazard.May cause mechanical eye or skin irritation in high concen-trations. As with all mineral spills, minimize dusting duringclean-up. Prolonged inhalation may cause lung injury. Prod-uct can become slippery when wet.

Finger Pickup Meters

EZ-Slide Graphite Powder

821-042C bottle, 1 pound (450 grams)821-060C jug, 5 pound (2.3 kg)

For Finger Pick Up Meters OnlyUse only approved Graphite Powder available fromGreat Plains Mfg. Inc. or Precision Planting to ensureproper lubrication of finger pickup corn seed meters.

Recommended usage:

For finger pickup meters, add one tablespoon (15 ml) ofgraphite for each unit of seed corn (80,000 kernels).

In high humidity conditions, or seeds with heavy seedtreatments, increase the application to two tbsp (30ml).

If delivery of seed from the hopper to the finger meter isan issue, add “Ezee Glide Plus” talc and graphite blendat a rate of one cup (237ml) per 4 units of seed. Adjustuntil issue is resolved.

Irritation and Chronic Exposure Hazard:Wear gloves. DO NOT use hands or any part of your body tomix seed lubricant. Wear a respirator when transferring andmixing. Avoid breathing lubricant dust. Not an acute hazard.May cause mechanical eye or skin irritation in high concen-trations. As with all mineral spills, minimize dusting duringclean-up. Prolonged inhalation may cause lung injury.

29248 25477

401-347B 08/02/2010


08/02/2010 401-347B


Great Plains Manufacturing, Inc.

Corporate Office: PO Box 5060Salina, KS 67402-5060 USA

401-347B 08/02/2010

seed rate charts - great plains · great plains mfg., inc. 2 401-347b 08/02/2010 setting planting...

Documents