seating module wire routing - motion concepts rev a...- joystick buss - m-series power buss -...

12
SEATING MODULE WIRE ROUTING for M-Series Electronics on Invacare Power Bases Seating Modules: Tilt Recline Tilt/Elevate Elevate-Only Base Electronics: MK6 Controller System Operation : Thru Joystick TECHNICAL MANUAL IMPORTANT! This manual contains electronics wire routing information for use only by trained/qualified technical personnel . Wire routing will be completed at the time of installation and prior to delivery. This manual is not to be given to the end user. TRD0391 REV A

Upload: others

Post on 14-Jul-2020

0 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

SEATING MODULE WIRE ROUTINGfor M-Series Electronics

on Invacare Power Bases

Seating Modules: TiltReclineTilt/ElevateElevate-Only

Base Electronics: MK6 Controller

System Operation: Thru Joystick

TECHNICAL MANUALIMPORTANT! This manual contains electronics wire routing information for use only bytrained/qualified technical personnel. Wire routing will be completed at the time ofinstallation and prior to delivery. This manual is not to be given to the end user.

TRD0391 REV A

Page 2: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

This manual may not be reproduced or reprinted either partly or completely without previous written consent fromMotion Concepts or its statutory representatives.

This manual is compiled from the latest product information available at the time of publication. We reserve theright to make any necessary as they become necessary. Any changes made to our products may cause slightvariations between the illustrations and explanations in this manual and the product you have purchased. If you haveany questions or concerns regarding the information provided in this manual, please contact our Customer ServiceDepartment for assistance.

Motion Concepts LP Copyright © 2015

Page 3: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

If you have any questions or concerns regarding the wire routing instructions contained in this manual, please

contact our Technical Service Department for assistance.

USA 888-433-6818

CAN 800-680-4191

SAFETY INFORMATION

READ ALL SAFETY INFORMATION THOROUGHLY BEFORE OPERATION!

WARNING! Danger of fire or breaking down due to electric devices being connected!

• Do not connect any electric devices to your mobility device that are not expressly certified Motion Conceptsfor this purpose. Have all electrical installations performed by an authorised Motion Concepts Dealer.

OEM Wiring Harnesses and Electronics

The cables and harnesses on your Motion Concepts power positioning system are designed and tested to meet

all necessary safety standards.

WARNING! The wiring harnesses/cables are not to be modified in any way following the installation

of the Motion Concepts power positioning system.

• If installed on previously used product, the existing OEM harnesses on the wheelchair should be examinedfor damage/ wear and replaced if necessary. Please consult the wheelchair base manufacturer if you are unsureas to the status or condition of the existing wiring harness before interfacing with our Motion Conceptsseating system.

IMPORTANT! Please be certain to also read and follow the safety warnings provided in the Power Base

Owners Manual (provided separately).

IMPORTANT! The instructions provided in this manual are intended solely to illustrate the proper Routing

of the various cables and harnesses on the Motion Concepts Power Positioning System. Please be cetain

to read and follow all safety warnings (including the Safety Lockout and Limit Switch Set-Up Warnings)

provided in the Motion Concepts Ultra-Low Maxx Owners Manual (TRD0384).

Page 4: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

IMPORTANT! Due to large variances from one seating system to the next (i.e. seat and back size, power

positioning options), the required fastening hardware can vary considerably.

1.0 Seating Module - Wire Routing Instruction for Invacare Power Bases

The instructions provided include illustrated wire routing diagrams for the following Motion Concepts

Seating Modules on an Invacare Power Base, with a MK6 Controller: Tilt Module (50T), Tilt/Elevate

Module (45T12) and 12” Elevate/Lift-Only Module (L12)

1.1 General Instructions:

1.1.1. The following fasteners are provided to ensure that all wiring cables/ harnesses are properly secured and

protected from damage during normal operation of the completed power positioning system. Please contact Motion

Concepts should require any additional fasteners to complete the installation.

• TRM0766 3/4” Clip • TRM0999 Flexo-Wrap 1-1/4”

• TRM0767 3/8” Clip • TRM0312 2” Velcro Loop

• TRM0768 1/2” Clip • Plastic Cables ties

• TRM0998 Flexo-Wrap 3/4”

1.1.2 During installation, the aforementioned fasteners should be used as needed to ensure that all wiring cables/

harnesses are properly secured and protected from damage (pinching, pulling, crushing) during normal operation

of the installed power positioning system.

1.1.5 Upon completion, verify the routing and security of all cables, and ensure there is no pulling, crushing or

pinching over the complete range of tilt, recline and elevate.

1.1.3 When routing the cables from the Invacare powerbase to the upper seating system, it may be necessary to

modify the wheelchair base shroud to allow a clear path for the cables and prevent any potential interference with

existing base components. Please refer to the Invacare power base Installation Instructions (provided separately)

for specific instructions regarding any base shroud modifications.

NOTE: The location of the shroud modification may vary depending on whichever side the Joystick is mounted

(routed).

1.1.4. The following section provides wire routing diagrams for Invacare Power Bases equipped with a MK6 Controller.

Refer to Table 1.0 below, to determine the applicable wiring configuration for your specific seating system module.

Table 1.0 – Seating Module Wiring Reference Chart- MK6 Electronics

Page 5: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

M270

Shear

R-Leg

L-Leg

Elev

Tilt

Recl

Tipsy

Lim Sw

Switch

PWR

Right

Legrest

Left

LegrestCentermount

Legrest

Sw

itch

(L

/H m

ount

)Seating Module Wire Routing for Invacare Power Bases

A SEAT PAN (TOP) VIEW (w/ M-Series Seat Control)

REAR

- Joystick Buss

- M-Series Power Buss

- M270

- Recline

- Tilt

- Elevate

- Limit Sw. (Elev DLO)

- Tipsy (Recline)

- Tipsy (Tilt-Only)

- L/H Switch (optional)

- R/H Switch (optional)

- Left Legrest (optional)

- Right/CM Legrest (optional)

8a

3

1

2

4

9a9b10a10b

3

4

10a

To Tilt Module,

Lift/Tilt Module,

or Lift-Only Module (as applicable)

1

7

1

Sw

itch

(R

/H m

ount

)

2

2

B1

B2

C

Recline Module

Tilt Backs

8b

7

5

6

*note: all options shown

5

6

9a

9a

9b

9b

9b

8b

8a

7

7

10a

10a

10b

10b

10b

BJo

ysti

ck

to Armrest

to Armrest

M-Series Control Box

TOP VIEW

Page 6: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

Tip

sy

- Joystick Buss

- M-Series Power Buss

- M270

- Recline

- Tipsy (Recline)

- L/H Switch (optional)

- R/H Switch (optional)

- MK6 Controller Buss

M-Series Control Box

Jo

ysti

ck

to Armrest

(L/H m

ount)

Optional S

witc

h

B UPPER VIEW- RECLINE BACK (w/ M-Series Seat Control)

to Armrest

PW

R B

uss

JO

Y B

uss

(R/H

mou

nt)

Opt

iona

l Sw

itch

M270

1

2

3

4

4

3

1

2

8a

9a

2

B1: Recline Module

9b9a

9b

8a

9a

9b

3

1

Seating Module Wire Routing for Invacare Power Bases

Contr

olle

r B

uss

11

11

Power Buss

(from MK6 Controller)

11

Page 7: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

(R/H

mou

nt)

Opt

iona

l Sw

itch

Jo

ysti

ck

(L/H m

ount)

Optional S

witc

h

to Armrest

to Armrest

Tip

sy

B2: TILT BACK

JO

Y B

uss

PW

R B

uss

M270

B UPPER VIEW- TILT BACK (w/ M-Series Seat Control)

Crossbrace

1

1

2

2

3

3

9b

9b

9a

9a

8b M-Series Control Box

5

- Joystick Buss

- M-Series Power Buss

- M270

- Tipsy (Tilt-Only)

- L/H Switch (optional)

- R/H Switch (optional)

- MK6 Controller Buss

3

1

2

8b

9b9a

11

11

Contr

olle

r B

uss

Power Buss

(from MK6 Controller)11

Seating Module Wire Routing for Invacare Power Bases

to Tilt Actuator

Page 8: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

C TILT, TILT/LIFT and LIFT-ONLY MODULES (w/ M-Series Seat Control)

C1: Tilt Module

M-Series Control Box4

Joystick Buss

Power Buss

(from MK6 Controller)

- Joystick Buss

- M-Series Power Buss

- Tilt

- MK6 Controller Buss

4

2

1 B

11

2

11

1

to Tilt Actuator

M-Series Control Box

- Joystick Buss

- M-Series Power Buss

- Tilt

- Elevate

- Limit Sw. (Elevate DLO)

- MK6 Controller Buss

C2: Tilt/Lift Module

Flexible Cable Track

5

6

4

Note: module shown in elevated position.

TILT, TILT/LIFT and LIFT-ONLY MODULES (w/ M-Series Seat Control)C

6

6

54

5

2

1

B

Joystick Buss

11Power Buss

(from MK6 Controller)

11

1

62

to Tilt Actuator

Seating Module Wire Routing for Invacare Power Bases

Page 9: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

Seating Module Wire Routing for Invacare TDX-SP/-SI/-SR

C3: Lift-Only Module

TILT, TILT/LIFT and LIFT-ONLY MODULES (M-Series Electronics)C

M-Series Control Box

- Joystick Buss

- M-Series Power Buss

- Elevate

- Limit Sw. (Elevate DLO)

- MK6 Controller Buss

Flexible Cable Track

5

6

Note: module shown in elevated position.

6

6

5

5

2

1

B

Joystick Buss

11Power Buss

(from MK6 Controller)

11

1

62

If you have any questions or concerns regarding the instructions contained in this manual, please contact

our Technical Service Department for assistance.

USA 888-433-6818

CAN 800-680-4191

Page 10: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

NOTES:

Page 11: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:
Page 12: SEATING MODULE WIRE ROUTING - Motion Concepts Rev A...- Joystick Buss - M-Series Power Buss - Elevate - Limit Sw. (Elevate DLO) - MK6 Controller Buss Flexible Cable Track 5 6 Note:

CANADAMotion Concepts LP Tel (local): 905-695-0134

84 Citation Drive, Unit 1-7 Tel (toll free): 866-748-7943

Concord, Ontario Fax: 905 695 0138

L4K 3C1 Tech Service: 800-680-4191

@ [email protected]

www. www.motionconcepts.com

USAMotion Concepts

700 Ensminger Rd, Suite 112 Tel.: 716-447-0050

Tonawanda, New York Tel (toll free): 866-433-6818

14150 Fax: 888-433-6834

Tech Service: 888-433-6818