sdr 11
TRANSCRIPT
Examples
1
Flow Charts for Polyethylene Pipe
TABLE OF CONTENTS
INTRODUCTION 2
Design Basis
Design Basis 3
Flow Variations 5
PE100 225mm to 1200mm PN6.3 – PN10 5
Gravity Main 6
Pumped Main
Part Full Flow 8
PE100 225mm to 1200mm 8
9
Pressure Rating (PN) 11
11PE Pipe - SDR33
12PE Pipe - SDR26
13
PE Pipe - SDR17 16
PE Pipe - SDR11 16
PE Pipe - SDR9 17
PE Pipe - SDR7.4 18
EXAMPLES 6
RESISTANCE 9
7
Above Ground Unprotected STD Black
Resistance Coefficients
FLOW CHARTS 10
Small Bore Polyethylene Pipe
PE Pipe - SDR21
PE Pipe - SDR13.6
POLYETHYLENE PIPE DIMENSIONS 19
15
10
HYDRAULIC DESIGN 3
Limitation of Liability
This product catalogue has been compiled by Vinidex Pty Limited (“the Company”) to promote better understanding of the technical aspects of the Company’s products to assist users in obtaining from them the best possible performance. The product catalogue is supplied subject to acknowledgement of the following conditions:
1 The product catalogue is protected by copyright and may not be copied or reproduced in any form or by any means in whole or in part without prior consent in writing by the Company. . 2 Product specifications, usage data and advisory information may change from time to time with advances in research and field experience. The Company reserves the right to make such changes at any time without further notice. 3 Correct usage of the Company’s products involves engineering judgements, which can not be properly made without full knowledge of all the conditions pertaining to each specific installation. The Company expressly disclaims all and any liability to any person whether supplied with this publication or not in respect of anything and all of the consequences of anything done or omitted to be done by any such person in reliance whether whole or part of the contents of this publication. 4 No offer to trade, nor any conditions of trading, are expressed or implied by the issue of content of this product catalogue. Nothing herein shall override the Company’s Condition of Sale, which may be obtained from the Registered Office or any Sales Office of the Company. 5 This product catalogue is and shall remain the property of the Company, and shall be surrendered on demand to the Company. 6 Information supplied in this product catalogue does not override a job specification, where such conflict arises; consult the authority supervising the job. © Copyright Vinidex Pty Limited.
VIN039 PE Flow Charts.indd 1 4/06/2009 9:30:08 AM
Examples
2
Flow Charts for Polyethylene Pipe
Introduction
The flow chaarts for VinidexPolyethylene (PE) pipes are suitable forpipes made to Australian Standard,AS/NZS 4130, Polyethylene (PE)pipes for pressure applications. ThisStandard includes several materialdesignations based on design stress.Because of this, pipes with the samedimensions but made from differentmaterials will have different pressureratings.
For simplicity, the large bore flowcharts are presented in terms of theStandard Dimension Ratio (SDR). TheSDR can be related to the materialdesignation and the pressure rating byreference to Table 1. The small borechart relates only to PE 80 materials andtherefore is presented in terms ofmominal size (DN) and nominalpressure class (PN).
Note: SDR Nominal ratio of outside diameter to wall thickness.PE classification Long term rupture stress at 20ºC (MPa multiplied by 10)
to which the minimum safety factor of 1.25 is applied in order to obtain the 20ºC design hoop stress.
PN Pressure rating at 20ºC (MPa multiplied by 10).
Table 1. Comparison of SDR & pressure rating for PE80 & PE100 materials
SDR 41 SDR 33 SDR 26 SDR 21 SDR 17 SDR 13.6 SDR 11 SDR 9 SDR 7.4
PE80 PN 3.2 PN 4 - PN 6.3 PN 8 PN 10 PN 12.5 PN 16 PN20
PE100 PN 4 - PN 6.3 PN8 PN 10 PN 12.5 PN 16 PN 2 PN 25
Pipe dimensions for polyethylene pipeare presented in Table 3 on page 2.
NoteAdvisory information concerning usage of the company’sproducts is published to assist users to obtain bestperformance, and represents the best informationavailable at the time of publication. No warranty isexpressed or implied, nor will any liability be accepted bythe Company for consequences resulting directly orindirectly from the use of such information.Product data and advisory information are subject tochange at any time without notice.
charts
19.
VIN039 PE Flow Charts.indd 2 4/06/2009 9:30:08 AM
Examples
3
Flow Charts for Polyethylene Pipe
Hydraulic DesignDesign Basis
Vinidex Polyethylene (PE) pipes offeradvantages to the designer due to thesmooth internal bores which aremaintained over the working lifetimeof the pipelines. The surface energycharacteristics of PE inhibit the build upof deposits on the internal pipesurfaces thereby retaining themaximum bore dimensions and flowcapacities.
The flow charts presented in thissection relate the combinations of pipediameters, flow velocities and headloss with discharge of water in PEpipelines. These charts have beendeveloped for the flow of waterthrough the pipes
Whee fluids other than water arebeing considered, the charts may notbe applicable due to the flowproperties of these different fluids. Inthese cases the advice of Vinidexengineers should be obtained.
There are a number of flow formulaein common use which have either atheoretical or empirical background.
However, only the Hazen-Williams andColebrook-White formulae areconsidered in this section.
Where fluids other than water arebeing considered, the charts may notbe applicable due to the flowproperties of these different fluids. Inthese cases the advice of Vinidexengineers should be obtained.
There are a number of flow formulaein common use which have either atheoretical or empirical background.
However, only the Hazen-Williams andColebrook-White formulae areconsidered in this section.
VIN039 PE Flow Charts.indd 3 4/06/2009 9:30:10 AM
Examples
4
Flow Charts for Polyethylene Pipe
Hazen – Williams
The original Hazen-Williams formulawas published in 1920 in the form:
Where
C1 = Hazen-Williams roughness coefficient
r = hydraulic radius (ft)
s = hydraulic gradient
The variations inherent with diameterchanges are accounted for by theintroduction of the coefficient C² sothat
Adoption of a Hazen-Williamsroughness coefficient of 155 results inthe following relationship for dischargein Vinidex PE pipes
Where
Q = discharge (litres/second)
D = internal diameter (mm)
H = head loss (metres/100 metres length of pipe)
Flow charts for pipe systems using theHazen – Williams formula have been inoperation in Australia for over 30years. The charts calculate thevolumes of water transmitted throughpipelines of various materials, and havebeen proven in practical installations.
10
× −
Colebrook – White
The development from first principlesof the Darcy – Weisbach formularesults in the expression
Where
And
f = Darcy friction factor
H = head loss due to friction(m)
D = pipe internal diameter (m)
L = pipe length (metres)
v = flow velocity (m/s)
g = gravitational acceleration(9.81 m/s2)
R = Reynolds Number
This is valid for the laminar flow region(R 2000), however, as most pipeapplications are likely to operate in thetransition zone between smooth andfull turbulence, the transition functiondeveloped by Colebrook-White isnecessary to establish the relationshipbetween f and R.
Where
k = Colebrook-White roughness coefficient (m)
The appropriate value for PE pipes is:
k = 0.007 x 10 -³ m
= 0.007 mm
This value provides for the range ofpipe diameters, and water flowvelocities encountered in normalpipeline installations.
/ 1 /+
VIN039 PE Flow Charts.indd 4 4/06/2009 9:30:10 AM
Examples
5
Flow Charts for Polyethylene Pipe
Head Loss in Fittings
Wherever a change to pipe crosssection, or a change in the direction offlow occurs in a pipeline, energy is lostand this must be accounted for in thehydraulic design.
Under normal circumstances involvinglong pipelines these head losses aresmall in relation to the head losses dueto pipe wall friction.
However, geometry and inlet/exitcondition head losses may besignificant in short pipe runs or incomplex installations where a largenumber of fittings are included in thedesign.
The general relationship for headlosses in fittings may be expressed as:
Where
H = head loss (m)
V = velocity of flow (m/s)
K = head loss coefficient
G = gravitational acceleration(9.81 m/s2)
The value of the head loss coefficientK is dependent on the particulargeometry of each fitting, and valuesfor specific cases are listed in Table 2.
The total head loss in the pipelinenetwork is the obtained by addingtogether the calculations performed foreach fitting in the system, the headloss in the pipes, and any other designhead losses.
Flow Variations
The flow charts presented for PE pipes are based on a number ofassumptions, and variations tothese standard conditions may require evaluation as to the effect on discharge.
Water Temperature
The charts are based on a watertemperature of 20C. A water
increase above this valueresults in a decrease in viscosity of thewater, with a corresponding increase indischarge (or reduced head loss)through the pipeline.
An allowance of approximately 1%increase in the water discharge mustbe made for each 3oC increase intemperature above 20oC. Similarly, adecrease of approximately 1% indischarge occurs for each 3oC stepbelow 20oC water temperature.
Pipe Dimensions
The flow charts presented in thissection are based on mean pipedimensions of Series 1 pipes made toAS/NZS 4130 PE pipes for Pressureapplications.
Surface Roughness
The roughness coefficients adopted forVinidex PE pipes result fromexperimental programs performed inEurope and the USA, and follow therecommendations laid down inAustralian Standard AS2200 – DesignCharts for Water Supply andSewerage.
temperature
“
“
Worked Example
What is the head loss occurring in a250mm equal tee with the flow in themain pipeline at a flow velocity of 2m/s?
Where
K = 0.35 (Table 2)
V = 2 m/s
G = 9.81 m/s
If the total system contains 15 teesunder the same conditions, then thetotal head loss in the fittings is 15 x0.07 = 1.05 metres.
2××
0.07-
VIN039 PE Flow Charts.indd 5 4/06/2009 9:30:10 AM
Examples
6
Flow Charts for Polyethylene Pipe
Figure 1. Gravity Flow Example
Example 1: Gravity Main (refer Figure 1)
A flow of water of 32 litres/second isrequired to flow from a storge tanklocated on a hill 50 metres above anoutlet. The tank is located 4.5 kmaway from the outlet.
Hence the information available is:
Head available = 50 metres
Length of pipeline = 4500 metresMinimum PN rating of pipe availableto withstand the 50 m static head isPN6.3. Head loss per 100 m length ofpipe is :
Use Table 1 to select the SDR rating ofPN6.3 class pipes in both PE80, andPE100 materials.
PE80 Material Option
PE80 PN6.3 pipe is SDR 21.
Use the SDR 21 flow chart, readintersection of discharge line at 32 l/sand head loss line at 1.11m/100m ofpipe. Select the next largest pipe size.This rsults in a DN200 mm pipediameter.
PE100 Material Option
Pe100 PN6.3 pipe is SDR 26.
Use the SDR26 flow chart, read theintersection of discharge line at 32 l/sand head loss line at 1.11m/100m ofpipe. Select the next largest pipe size.This results in a DN180mm pipediameter.
Hence for this application, there aretwo options available, either:
1. DN200 PE80 PN6.3 or
2. Dn 180 PE100 PN6.3
×
Flow Chart Worked Examples
(refer Figure 1)PE80 Material Option
PE80 PN6.3 pipe is SDR 21.
Use the SDR 21 flow chart, readintersection of discharge line at 32 l/sand head loss line at 1.11m/100m ofpipe. Select the next largest pipe size.This results in a DN200 mm pipediameter.
PE100 Material Option
PE100 PN6.3 pipe is SDR 26.
Use the SDR26 flow chart, read theintersection of discharge line at 32 l/sand head loss line at 1.11m/100m ofpipe. Select the next largest pipe size.This results in a DN180mm pipediameter.
Hence for this application, there aretwo options available, either:
1. DN200 PE80 PN6.3 or
2. DN 180 PE100 PN6.3
VIN039 PE Flow Charts.indd 6 4/06/2009 9:30:11 AM
Examples
7
Flow Charts for Polyethylene Pipe
Example 2: Pumped Main
(refer Figure 2)
A line is required to provide 20 litres/second of water from a dam to a highlevel storage tank located 5000 metresaway. The tank has maximum waterelevation of 100m and the minumumwater elevation in the dam is 70m.
The maximum flow velicity is requiredto be limited to 1.0 metres/second tominimise water hammer effects.
The maximum head required at thepump = static head + pipe frictionhead + fittings form loss
1. Static Head
= 100 – 70 = 30 m
2. Pipe Friction Head
Considering the data available, startwith a PN6.3 class pipe.
PE80 Material Option
From Table 1, PE80 PN6.3 pipe isSDR21. Use the SDR 21 flow chart,find the intersection of the dischargeline at 20 l/s and the velocity line at 1m/s. Select the corresponding or nextlargest size of the pipe. Where thedischarge line intersects the selectedpipe size, trace across to find the headloss per 100m length of pipe.
This gives a value of 0.5m/100m.
Calculate the total friction head loss inthe pipe:
Then from the flow chart, estimate thevelocity of flow This gives 1 m/s.
3. Fittings Head Losses
From Figure 2, identify the type and number ofdifferent fittings used in the pipeline. Select theappropriate form factor value K for each fittingtype from Table 2. Then:
×
2
=
=×
Fitting Form Head loss m
factor K
Foot Valve 15.0 15 x 0.05 = 0.75
Gate Valve 0.2 2 x 0.2 x 0.05 = 0.02
Reflux Valve 2.5 2.5 x 0.05 = 0.125
Elbow 0.35 2 x 0.35 x 0.05 = 0.035
Elbow 1.10 4 x 1.1x 0.05 = 0.220= 0
Total fittings head loss = 1.2
4. Total Pumping Head
= 30 + 25 + 1.2 = 56.2m
allow 57m
Note: The example does not make any provision forsurge allowance in pressure class selection.
Figure 2. Pumped Flow Example
Square Outlet 1.0 1.0 x 0.05 = 0.050
VIN039 PE Flow Charts.indd 7 4/06/2009 9:30:12 AM
Examples
8
Flow Charts for Polyethylene Pipe
From Part Full Flow graph (Figure 3)for a proportional depth of 0.44, theproportional velocity if 0.95.Refer to the Vinidex PE pipe flow chartfor the SDR 21 pipe.For a gradient of 1 in 100 full flow is39 l/s and the velocity is 1.6 m/s.
Then, for part full flow
Discharge = 0.4 x 39= 15.6 l/s
Velocity = 0.95 x 1.6= 1.52 m/s
Figure 3. Part Full Flow
Example 3: Determine flow velocityand discharge under part full flowconditions.
Given gravity conditions:
Pipe: DN 200 PE80 PN6.3
Mean pipe ID: 180mm (Refer Table 3
– PE Pipe Dimensions,
or AS/NZS 4130)
Gradient: 1 in 100
Depth of flow: 80mm
Problem: Find flow and velocity
Solution:
Part Full Flow
Non pressure pipes are designed to runfull under anticipated peak flowconditions. However, for aconsiderable period the pipes run atless than full flow conditions and in these circumstances they act asopen channels with a free fluid to airsurface.
In these instances consideration mustbe given to maintaining a minimumtransport velocity to prevent depositionof solids and blockage of the pipeline.
For pipes flowing part full, the mostusual self cleansing velocity adoptedfor sewers is 0.6 metres/second.
KepyT gnittiFGradual Enlargements
lacipyt 01 = q D/d oitaR0.9 0.020.7 0.130.5 0.290.3 0.42
Gradual Contractionslacipyt º01 = θD/d oitaR
0.9 0.030.7 0.080.5 0.120.3 0.14
Valves02.0)nepo ylluf( evlaV etaG
Reflux Valve 2.50
00.01evlaV ebolG
02.0)nepo ylluf( evlaV ylfrettuB
00.5evlaV elgnA
Foot Valve with strainer 15.00
orezsevlaV riA
01.0evlaV llaB
Pipe Exit Losses00.1teltuO erauqS
Rounded Outlet 1.00
Table 2. Resistance CoefficientsValves, Fittings and Changes in Pipe Cross-section
KepyT gnittiF
Pipe Entry Losses
05.0telnI erauqS
08.0telnI tnartne-eR
52.0telnI dednuoR ylthgilS
50.0telnI htuomlleB
Pipe Intermediate LossesElbows R/D <0.6 45o 0.35
90o 1.10
Long Radius Bends (R/D>2) 11 1/4o 0.05
22 1/2o
0.1045o 0.2090o 0.50
Tees(a) Flow in line 0.35
(b) Line to branch flow 1.00
Sudden EnlargementsRatio d/D
0.9 0.040.8 0.130.7 0.260.6 0.410.5 0.560.4 0.710.3 0.830.2 0.92<0.2 1.00
Sudden ContractionsRatio d/D
0.9 0.100.8 0.180.7 0.260.6 0.320.5 0.380.4 0.420.3 0.460.2 0.48<0.2 0.50
VIN039 PE Flow Charts.indd 8 4/06/2009 9:30:15 AM
Examples
9
Flow Charts for Polyethylene Pipe
KepyT gnittiFGradual Enlargements
lacipyt 01 = q D/d oitaR0.9 0.020.7 0.130.5 0.290.3 0.42
Gradual Contractionslacipyt º01 = θD/d oitaR
0.9 0.030.7 0.080.5 0.120.3 0.14
Valves02.0)nepo ylluf( evlaV etaG
Reflux Valve 2.50
00.01evlaV ebolG
02.0)nepo ylluf( evlaV ylfrettuB
00.5evlaV elgnA
Foot Valve with strainer 15.00
orezsevlaV riA
01.0evlaV llaB
Pipe Exit Losses00.1teltuO erauqS
Rounded Outlet 1.00
Table 2. Resistance CoefficientsValves, Fittings and Changes in Pipe Cross-section
KepyT gnittiF
Pipe Entry Losses
05.0telnI erauqS
08.0telnI tnartne-eR
52.0telnI dednuoR ylthgilS
50.0telnI htuomlleB
Pipe Intermediate LossesElbows R/D <0.6 45o 0.35
90o 1.10
Long Radius Bends (R/D>2) 11 1/4o 0.05
22 1/2o
0.1045o 0.2090o 0.50
Tees(a) Flow in line 0.35
(b) Line to branch flow 1.00
Sudden EnlargementsRatio d/D
0.9 0.040.8 0.130.7 0.260.6 0.410.5 0.560.4 0.710.3 0.830.2 0.92<0.2 1.00
Sudden ContractionsRatio d/D
0.9 0.100.8 0.180.7 0.260.6 0.320.5 0.380.4 0.420.3 0.460.2 0.48<0.2 0.50
VIN039 PE Flow Charts.indd 9 4/06/2009 9:30:15 AM
Examples
10
Flow Charts for Polyethylene Pipe
Flow Chart for Small Bore Polyethylene Pipe
VIN039 PE Flow Charts.indd 10 4/06/2009 9:30:16 AM
Examples
11
Flow Charts for Polyethylene Pipe
Flow Chart for Polyethylene Pipe - SDR 41
VIN039 PE Flow Charts.indd 11 4/06/2009 9:30:16 AM
Examples
12
Flow Charts for Polyethylene Pipe
Flow Chart for Polyethylene Pipe - SDR 33
VIN039 PE Flow Charts.indd 12 4/06/2009 9:30:17 AM
Examples
13
Flow Charts for Polyethylene Pipe
Flow Chart for Polyethylene Pipe - SDR 26
VIN039 PE Flow Charts.indd 13 4/06/2009 9:30:18 AM
Examples
14
Flow Charts for Polyethylene Pipe
Flow Chart for Polyethylene Pipe - SDR 21
VIN039 PE Flow Charts.indd 14 4/06/2009 9:30:18 AM
Examples
15
Flow Charts for Polyethylene Pipe
Flow Chart for Polyethylene Pipe - SDR 17
VIN039 PE Flow Charts.indd 15 4/06/2009 9:30:19 AM
Examples
16
Flow Charts for Polyethylene Pipe
Flow Chart for Polyethylene Pipe - SDR 13.6
VIN039 PE Flow Charts.indd 16 4/06/2009 9:30:19 AM
Examples
17
Flow Charts for Polyethylene Pipe
Flow Chart for Polyethylene Pipe - SDR 11
VIN039 PE Flow Charts.indd 17 4/06/2009 9:30:20 AM
Examples
18
Flow Charts for Polyethylene Pipe
Flow Chart for Polyethylene Pipe - SDR 9
Min
ing
& I
nd
ust
rial
Man
ual
48
flo
w c
ha
rt
fo
r p
oly
et
hy
len
e p
Ipe –
sd
r 9
sec
tIo
n 5
flo
w c
ha
rt
s fo
r p
e
Head Loss – Metres Head of Water per 100 meters of Pipe
Dis
char
ge
– Li
tres
per
Sec
ond (L/
s)
VIN039 PE Flow Charts.indd 18 4/06/2009 9:30:20 AM
Examples
19
Flow Charts for Polyethylene Pipe
Flow Chart for Polyethylene Pipe - SDR 7.4
VIN039 PE Flow Charts.indd 19 4/06/2009 9:30:31 AM
Examples
20
Flow Charts for Polyethylene Pipe
Table 3. PE Pipe Dimensions
Nom
.Si
zeD
N
16 20 25 32 40 50 63 75 90 110
125
140
160
180
200
225
250
280
315
355
400
450
500
560
630
710
800
900
1000
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.9
2.2
2.7
3.1
3.5
4.0
4.4
4.9
5.5
6.2
6.9
7.7
8.7
9.8
11.0
12.3
13.7
15.4
17.4
19.6
22.0
24.5
Min
Wal
l
Thi
ckne
ss
(mm
)
Mea
n
I.D.
(mm
)
SDR
41
Min
Wal
l
Thi
ckne
ss
(mm
)
Mea
n
I.D.
(mm
)
SDR
33
Min
Wal
l
Thi
ckne
ss
(mm
)
Mea
n
I.D.
(mm
)
SDR
26
Min
Wal
l
Thi
ckne
ss
(mm
)
Mea
n
I.D.
(mm
)
SDR
21
Min
Wal
l
Thi
ckne
ss
(mm
)
Mea
n
I.D.
(mm
)
SDR
17
Min
Wal
l
Thi
ckne
ss
(mm
)
Mea
n
I.D.
(mm
)
SDR
13.
6M
in W
all
Thi
ckne
ss
(mm
)
Mea
n
I.D.
(mm
)
SDR
11
Min
Wal
l
Thi
ckne
ss
(mm
)
Mea
n
I.D.
(mm
)
SDR
9M
in W
all
Thi
ckne
ss
(mm
)
Mea
n
I.D.
(mm
)
SDR
7.4
13 17 22 29 37 47 60 71 86 105
119
133
152
171
190
215
238
267
300
338
380
429
476
534
600
676
762
858
953
1.6
1.6
1.6
1.6
1.6
1.6
2.0
2.3
2.8
3.4
3.9
4.3
4.9
5.5
6.2
6.9
7.7
8.6
9.7
10.9
12.3
13.8
15.3
17.2
19.3
21.8
24.5
27.6
30.6
13
17
22
29
37
47
59
70
84
103
117
131
150
169
188
211
235
263
296
333
376
422
470
526
592
667
752
846
940
1.6
1.6
1.6
1.6
1.6
2.0
2.4
2.9
3.5
4.3
4.8
5.4
6.2
6.9
7.7
8.6
9.6
10.7
12.1
13.6
15.3
17.2
19.1
21.4
24.1
27.2
30.6
34.4
38.2
13
17
22
29
37
46
58
69
83
101
115
129
148
166
184
207
230
258
290
328
370
415
462
518
582
656
739
831
924
1.6
1.6
1.6
1.6
1.9
2.4
3.0
3.6
4.3
5.3
6.0
6.7
7.7
8.6
9.6
10.8
11.9
13.4
15.0
16.9
19.1
21.5
23.9
26.7
30.0
33.9
38.1
42.9
47.7
13
17
22
29
36
45
57
67
81
99
113
126
144
163
180
203
225
253
285
320
362
406
452
506
570
641
723
814
904
1.6
1.6
1.6
1.9
2.4
3 3.8
4.5
5.4
6.6
7.4
8.3
9.5
10.7
11.9
13.4
14.8
16.4
18.7
21.1
23.7
26.7
29.6
33.2
37.3
42.1
47.4
53.5
59.3
13
17
22
28
35
44
55
66
78
96
110
123
140
158
175
198
219
246
278
311
351
395
440
494
554
624
704
791
880
1.6
1.6
1.9
2.4
3.0
3.7
4.7
5.5
6.6
8.1
9.2
10.3
11.8
13.3
14.7
16.6
18.4
20.6
23.2
26.1
29.4
33.1
36.8
41.2
46.3
52.2
58.8
- -
13
17
21
27
34
42
53
63
76
93
106
118
136
153
170
191
212
238
268
301
340
382
424
475
535
603
679
- -
1.6
1.9
2.3
2.9
3.7
4.6
5.8
6.8
8.2
10.0
11.4
12.7
14.6
16.4
18.2
20.5
22.7
25.4
28.6
32.2
36.3
40.9
45.4
50.8
57.2
- - - -
13
16
20
26
32
40
51
61
73
89
101
114
130
145
162
183
203
228
256
289
326
366
407
455
512
- - - -
1.8
2.3
2.8
3.6
4.5
5.6
7.1
8.4
10.1
12.3
14.0
15.7
17.9
20.1
22.4
25.1
27.9
31.3
35.2
39.6
44.7
50.2
55.8
- - - - - -
12
15
19
24
31
38
48
58
69
84
96
108
123
138
154
173
192
215
242
273
307
347
348
- - - - - -
2.2
2.8
3.5
4.4
5.5
6.9
8.6
10.3
12.3
15.1
17.1
19.2
21.9
24.6
27.3
30.8
34.2
38.3
43.0
48.5
54.6
61.5
- - - - - - -
11
14
18
23
28
35
45
53
65
78
89
99
114
128
143
161
179
200
226
225
287
322
- - - - - - -
POLY
ETH
YLE
NE
PIPE
DIM
ENSI
ON
S (B
ased
on
AS/
NZS
413
0:20
03, P
olye
thyl
ene
pipe
s fo
r pr
essu
re a
pplic
atio
ns).
SDR
- N
omin
al R
atio
of
outs
ide
diam
eter
to
wal
l thi
ckne
ss.
I.D. -
Inte
rnal
Dia
met
er
VIN039 PE Flow Charts.indd 20 4/06/2009 9:30:31 AM