sdm102e
TRANSCRIPT
-
TESTO ITC KORINNA 28mm Allargato
MONOBLOCKDIRECTIONAL CONTROL VALVE
-
SDM102
2 DAT011E
Features
Simple, compact and heavy duty designed 2 sections monoblock valve are used in Front Loader application with open centre andclosed centre hydraulic systems.H Parallel circuit.H Fitted with a main pressure relief valve and a load check valve on every working section.H Available with manual and remote with flexible cables spool control kits.H Diameter 16 mm -- 0.63 in interchangeable spools.H Available with service valve prearrangement.H Optional carry--over port.
WARNING!All specifications of this catalogue refers to the standard product at thisdate. Walvoil, oriented to a continuous improvement, reserves the right to
discontinue, modify or revise the specifications, without notice.
WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN
INCORRECT USE OF THE PRODUCT.3rd edition January 2000:This edition supercedes all prior documents.
Additional informationThis catalogue shows the product in the most usual configurations.Please contact Customer Service Dpt. for more detailled information orspecial request.
-
SDM102
3DAT011E
Contents
ContentsWorking conditions 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dimensional data 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hydraulic circuit 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Performance data 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ordering codes 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Inlet relief options 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Spool options 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A side spool positioners 14. . . . . . . . . . . . . . . . . . . . . . . . . . .B side options 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Port relief options 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Outlet conversion port options 20. . . . . . . . . . . . . . . . . . . . . . .Installation and maintenance 21. . . . . . . . . . . . . . . . . . . . . . . .
-
SDM102
4 DAT011E
This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm2/s -- 46 cSt viscosity at 40C tempera-ture.
Nominal flow rating 45 l/min
Operating pressure (maximum) 250 bar 3600 psi
Max. back pressure on outlet port T 25 bar 360 psi
Internal leakage A(B)T Dp=100 bar -- 1450 psifluid and valve at 40C -- 104F
3 cm3/min 0.18 in3/min
Fluid Mineral oil
Fluid temperature with NBR (BUNA--N) seals from --20 to 80C
with FPM (VITON) seals from --20 to 100C
Viscosity operating range from 15 to 75 mm2/s from 15 to 75 cSt
min. 12 mm2/s 12 cSt
max. 400 mm2/s 400 cSt
Max level of contamination 19/16 -- ISO 4406
Ambient temperature from --40 to 60C
NOTE -- For different conditions please contact Customer Service.
Working conditions
-
Dimensional data
WALVOIL
P9900001
102020003
MADE IN ITALYValve code
Production batch :P99 = production year (1999)00001 = progressive number
39 1.54
75.5
2.97
39 1.54
75.5
2.97
80.5
3.17
35.51.40
361.42
35.51.40
1003.94
11.50.45
9.50.37
P1 T1
SDM102/2P
P B1 A1 A2 B2 T
311.22
883.46
190.75
371.46
381.50
40.16
1505.911596.26
21 0.83
70 2.76
72 2.85
120
4.72
235
9.25
50.20
30 1.18
391.54
99.53.92
26 1.02
56.5
2.22
44.51.75
391.54
25.5
1.00
20.50.81
6 0.24
12 0.47 22 0.87
M8
100.39
WALVOIL102020003P9900001
MADE IN ITALY
Carry--over
SDM102
5DAT011E
Standard threads
PORTS BSP(ISO228/1)
SAE UN--UNF METRIC(ISO 262)
Inlet P and carry--over C SAE 8 (3/4--16 UNF)A and B ports G 3/8 SAE 6 (9/16--18 UNF) M18x1.5Outlet T SAE 8 (3/4--16 UNF)
-
Hydraulic circuit
A1 B1 A2 B2
P
P1
T
T1
Ex.:SDM102/2--P(TG3--175)/513RSLP/18MCSLP/AET--PSC--
Standard configuration
1752500
A1 B1 A2 B2PP1 T
T1
1752500
Ex.:SDM102/2--P(TG3--175)/513RSLP/18MCSLP/AET--PSL--
Side inlet and outlet ports configuration
Pressure relief valve
P T
T1P1
Tank linePressure line
A port line
B port line
Spool
A2
Load check valveAllen wrench 6 -- 24 Nm / 17.7 lbft
Allen wrench 624 Nm / 17.7 lbft
Allen wrench 624 Nm / 17.7 lbft
SDM102
6 DAT011E
-
Work port to outlet
Inlet to work port
Open centre
Performance data (pressure drop vs. flow)
A1A2
B1B2
PT
0
5
10
15
20
0 10 20 30 40 50 60Flow
Pre
ssur
edr
op
270
180
90
(l/min)
(bar)(psi)
A2(B2)T
A1(B1)T
0
5
10
15
20
0 10 20 30 40 50 60Flow
Pre
ssur
edr
op
270
180
90
(l/min)
(bar)(psi)
0
5
10
15
20
0 10 20 30 40 50 60Flow
Pre
ssur
edr
op
270
180
90
(l/min)
(bar)(psi)
NOTE -- Measured with spools type 1 and 5 (standard configuration)
PA2(B2)
PA1(B1)
A1A2
B1B2
PT
From cap side inlet to outlet (PSC configuration).
From cap side inlet to A port (spool in position 1) or B port (spool in position 2).
From A port (spool in position 2) or B port (spool in position 1) to outlet
A1A2
B1B2
PT
SDM102
7DAT011E
-
SDM102
8 DAT011E
5. B side options page 15
1. Body kit *
4. A side spool positioners page 14
3. Spool options page 11
2. Inlet relief options page 10
Ordering codes
Example:
1.
SDM102 / 2--P (TG3 -- 175) / 5 13R SLP . U175UT / 18MCSLP . UTUT / AET -- PSC -- *
TYPE CODE DESCRIPTION2--P 5KC1853000 2 section, without valve prearrangement2--P 5KC1853001 2 section, with valve prearrangement on
each section
TYPE CODE DESCRIPTIONVMD080 direct pressure relief valve type T(TG2--80) X162121080 Range 63 to 125 bar / 900 to 1800 psi
standard setting 80 bar / 1150 psi(TG3--175) X162121175 Range 100 to 200 bar / 1450 to 2900 psi
standard setting 175 bar / 2500 psi(TG4--250) X162121250 Range 160 to 250 bar / 2300 to 3600 psi
standard setting 250 bar / 3600 psiStandard setting is referred to 10 l/min flow.
SV XTAP524340 Relief valve blanking plug
TYPE CODE CIRCUIT DESCRIPTION1 3CU5210100 Double acting, 3 positions, with A and B
closed in neutral position5 3CU5242100 Double acting, 4 positions, with A and B
to tank in 4th position (float)8 3CU5262100 Double acting, 4 positions, with regenerative
in 4th position
2. 3. 4. 5.
Include body, seals, rings and load check valve.
6.
1st section 2nd section
TYPE CODE DESCRIPTION8MC 5V08205000 With spring return in neutral position13R 5V13306010 With detent in position 3, spring return in
neutral position13F 5V13505100 With spring return in neutral position and
reduced stroke
4.
8MC
13R
1.
13F
6.U C UT
7. Black painted
TYPE CODE DESCRIPTIONSLP 5COP107000 Without lever, with dust--proof plateLG 5LEV107805 Cast iron lever boxTQ 5TEL107100 Prearranged for cable remote controlLCB 5CLO202000 Mechanical joystick
8.
8.
8.
Pressure relief valve setting in bar
NOTE (*) -- Items are referred to BSP thread.
F
J
F
J
F
J
-
SDM102
9DAT011E
8. Inlet and outlet plugs *
7. Outlet conversion port options * page 20
6. Port relief options page 18
Ordering codes
I Optional handlevers
TYPE CODE DESCRIPTIONAET 3XTAP822150 Open centre (nr.1 SAE 8 plug required)AE XGIU524551 G 3/8 carry--over sleeveAEK 5GIU527580 Closed centre kit
2.
T
SV
3.
5.
SLP
LG
I
TQ
LCB
7.
AET
AE
AEK
TYPE CODE DESCRIPTIONAnti--shock and anti--cavitation valvesU025 5KIT326025 Setting to 25 bar / 360 psiU040 5KIT326040 Setting to 40 bar / 580 psiU060 5KIT326060 Setting to 60 bar / 870 psiU070 5KIT326070 Setting to 70 bar / 1000 psiU080 5KIT326080 Setting to 80 bar / 1150 psiU090 5KIT326090 Setting to 90 bar / 1300 psiU100 5KIT326100 Setting to 100 bar / 1450 psiU125 5KIT326125 Setting to 125 bar / 1800 psiU140 5KIT326140 Setting to 140 bar / 2030 psiU160 5KIT326160 Setting to 160 bar / 2300 psiU175 5KIT326175 Setting to 175 bar / 2500 psiU190 5KIT326190 Setting to 190 bar / 2750 psiU210 5KIT326210 Setting to 210 bar / 3050 psiU230 5KIT326230 Setting to 230 bar / 3300 psiU250 5KIT326250 Setting to 250 bar / 3600 psiU260 5KIT326260 Setting to 260 bar / 3750 psiU280 5KIT326280 Setting to 280 bar / 4000 psiStandard setting is referred to 10 l/min flow.
C 5KIT426270 Anti--cavitation valveUT XTAP221340 A and B port valve blanking plug
TYPE CODE DESCRIPTIONAL01/M10x150 170012015 For LG lever box
L = 150 mm / 5.91 inAL08/M12x200 170013120 For LCB joystick L = 200 mm / 7.87 in
TYPE CODE DESCRIPTIONPSC 3XTAP722160 Cap side inlet and outlet (G 3/8 nr.2 plugs
required)PSL 3XTAP722160 Side inlet and outlet (G 3/8 nr.2 plugs
required)
1
5
8
I
NOTEJ F -- Spools and positioners with the same symbol must be assembled together: for more informations see relevant pages.
F
J
-
SV: relief valve blanking plug
Pressure relief valve
Inlet relief options
0
100
200
300
0 20 40 60
VMD080 ( T G 3 -- 175)
Pressure setting in bar (standard 175 bar -- 2540 psi).
Adjustable spring type (2, 3, 4).Adjustment type (G, Z).
Performance data
Adjustemt type
44 max.
Wrench 24 -- 42 Nm / 31 lbft
Allen wrench 5
Wrench 19 -- 24 Nm / 17.7 lbft
0
100
200
300
0 20 40 60
4
Allen wrench 642 Nm / 31 lbft
1.80
Flow
Pre
ssur
e
(l/min)
(psi)(bar)
0.16
G: with screw Z: with tamper proof cap
Spring nr. 3
0
100
200
300
0 20 40 60Flow
Pre
ssur
e
(l/min)
(psi)(bar)
3000
2000
1000
Spring nr. 2
Flow
Pre
ssur
e
(l/min)
(psi)(bar)
Spring nr. 4
0.26RESPONSE TIME
10%
175
bar
2500
psi90%
95%
105%
Pre
ssur
e
Time ()
(% DP)
Response time
4000
3000
2000
1000
4000
3000
2000
1000
4000
Cap code: 3COP124180
471.85
SDM102
10 DAT011E
-
FJ
YP(on ports) = 63bar/900psiP(on ports) = 100bar/1450psiP(on ports) = 250bar/3600psi
Qin = 45 l/min
0
10
20
30
40
50
0.0 1.0 2.0 3.0 4.0 5.0
Spool metering A(B)T
Flow
Stroke (mm)
(l/min )
(in)0.1 0.2
5.50
10
20
30
40
50
0.0 1.0 2.0 3.0 4.0 5.0
Spool metering PA(B)
Flow
Stroke (mm)
(l/min )
(in)0.1 0.2
5.5
Performance data
F JY
FJ Y
Type 1
Spools
A
"
stroke =
P A B T
A BT TLC
P B A T
TP
P--A--B--T closed, with flow through line open
3010
39
169
201A B
P T
A B
P T
201
201A B
P T
0.39
6.65
-- 5.5 mm-- 0.22 in
stroke =+ 5.5 mm+ 0.22 in
1.18
1.54
A BT TLCTP
A BT TLCTP
Must be used only on 2nd section valve with positioner kit type 8MC .
SDM102
11DAT011E
-
FJ
YP(on ports) = 63bar/900psiP(on ports) = 100bar/1450psiP(on ports) = 250bar/3600psi
Qin = 45 l/min
0
10
20
30
40
50
0.0 1.0 2.0 3.0 4.0 5.0
Spool metering A(B)T
Flow
Stroke (mm)
(l/min )
(in)0.1 0.2
5.50
10
20
30
40
50
0.0 1.0 2.0 3.0 4.0 5.0
Spool metering PA(B)
Flow
Stroke (mm)
(l/min )
(in)0.1 0.2
5.5
Performance data
FJ Y
F JY
Type 5
Spools
A
"
stroke =
P A B T
A BT TLC
P B A T
TP
P--A--B--T closed, with flow through line open
-- 5.5 mm-- 0.22 in
stroke =+ 5.5 mm+ 0.22 in
A BT TLCTP
A BT TLCTP
A BT TLCTP
A(B) T (float)Float only with 13R positioner kit
A stroke =-- 10 mm-- 0.39 inA
201A B
P T
3
201A B
P T
3
201A B
P T
3
201A B
P T
3
Must be used only on 1st section valve with positioner kit type 8MC or 13R.
NOTE -- AA Only for positioner kit type 13R.
SDM102
12 DAT011E
-
FJ
YP(on ports) = 63bar/900psiP(on ports) = 100bar/1450psiP(on ports) = 250bar/3600psi
Qin = 45 l/min
0
10
20
30
40
50
0.0 1.0 2.0 3.0 4.0 5.0
Spool metering PA(B)
Flow
Stroke (mm)
(l/min )
(in)0.1 0.2
5.5
Performance data
F JY
Type 8
Spools
0
5
10
15
20
0 15 30 45
Spool pressure drop AB(in position 3)
Pre
ssur
edr
op
Flow (l/min)
(bar)(psi)
100
200
A
"
stroke =
P AB T
A BT TLC
P BA T
TP
P--A--B--T closed, with flow through line open
-- 4.5 mm-- 0.18 in
stroke =+ 4.5 mm+ 0.18 in
A BT TLCTP
A BT TLCTP
A BT TLCTP
P A--B (regenerative)
A stroke =-- 7.5 mm-- 0.30 inA
201A B
P T
3
201A B
P T
3
201A B
P T
3
201A B
P T
3
Must be used only in 2nd section valve with positioner kit type 13F.
SDM102
13DAT011E
-
--400
--200
0
200
400
--10.0 --8.0 --6.0 --4.0 --2.0 0.0 2.0 4.0(mm)
Forc
e
Force--stroke diagram
Stroke
(N) (lbf)
0 (in)0.20.1
5.5
80
40
--80
--40
0
--0.2 --0.1--0.3
From position 0 to 1
From position 0 to 2
From position 2 to 3
Locking--unlocking areaLocking force: 320 N / 71.9 lbf 10%Unlocking force: 315 N / 70.8 lbf 10%
--400
--200
0
200
400
--7.5 --6.0 --4.5 --3.0 --1.5 0.0 1.5 3.0 4.5(mm)
Forc
e
Force--stroke diagram
Stroke
(N)
(in)
80
40(lbf)
0--0.05--0.1--0.15--0.2--0.25 0.05 0.1 0.15
--80
--40
0From position 0 to 1From position 0 to 2
From position 2 to 3
(mm)
--200
--100
0
100
200
--5.5 --4.5 --3.5 --2.5 --1.5 --0.5 0.5 1.5 2.5 3.5 4.5 5.5
Forc
e
DCB
Force--stroke diagram
Stroke
(N)0.1 0.2 (in)
20
10(lbf)
--0.1--0.2 0
--20
--10
0
0
DCB
With detent on 4th position float circuit
With spring return -- 4th position regenerative circuit
With spring return
A side spool positioners
201
8MC kit
Supplied with standard spring type C (see force--stroke diagram); available with lighter spring type B (8MB code: 5V08505000) orheavier type D (8 code: 5V08105000).
Allen wrench 46.6 Nm / 4.9 lbft
Allen wrench 59.8 Nm / 7.2 lbft
36.51.44
833.27
722.85
201 3
13F kit
13R kit
201 3
Must be used with spool type 8 (page 13).
Must be used with spool type 5 (page 12).
Allen wrench 46.6 Nm / 4.9 lbft
Allen wrench 59.8 Nm / 7.2 lbft
Allen wrench 46.6 Nm / 4.9 lbft
Wrench 69.8 Nm / 7.2 lbft
SDM102
14 DAT011E
-
LG cast iron lever box
SLP dust proof plate
B side options
201With protection boot lever pivot box; it can be rotated 180 (LG180 configuration).Also available alluminium lever box: L configuration, code 5LEV107900
NOTE -- The handlever must be ordered separately (see page 9).
Mechanical control with dust proof plate201
100.39
301.18
391.54
150.
59
40.16
1.5 x 45
220.8721
0.839H80.35 +.0009
80.
31
160.
63
0.06
30
81.5
3.21
65.5
2.58
20 0.79
44.5
1.75
301.18
572.24
C
21 03
A B
Vertical handleverassembly
Horizontal handleverassembly
M 10
Spool dimension
136.
55.
37
21 0.83
37 1.46
LG180 configuration
Spool typeLever angle
15 15 13
1 5 8
A
15 15 13B
/ 27 21C
Allen wrench 46.6 Nm / 4.9 lbft
Allen wrench 46.6 Nm / 4.9 lbft
SDM102
15DAT011E
-
TQ cable remote control
B side options
201Waterproof cap prearranged for remote control with flexible cable.
913.58
CD flexible cable to be ordered separately
Wrench 24
NOTE -- For more information concerning remote cable control require appropriate documentation.
Allen wrench 46.6 Nm / 4.9 lbft
Wrench 10
Example of cable control
P1
T1
PB1A1A2B2T
SCF030 remote control
CD flexible cables
SDM102 directional controlvalve with TQ cable control kit
SDM102
16 DAT011E
-
Mechanical joystick LCB
B side options32 1.2644
.51.
7510
.50.
41
110
4.33
381.50
10.50.41
M12
201
201
Dimensions and movement scheme
B1
A2
A1
B2
A2--B1 B1--B2
A2--A1 B2--A1
Execution LCB1pivot placed down on the left
873.43
1st section spool
2nd section spool
Execution LCB2pivot placed down on the right
B2
B1
A2
A1
B1--B2 B2--A1
B1--A2 A1--A2
381.50
10.50.41
spool axis
2st section axis1st section axis
44.5
1.755
72.
24
381.50
10.50.41
A1
A2
B1
B2
A2--A1 A1--B2
A2--B1 B1--B2
Execution LCB3pivot placed above on the left
381.50
10.50.41
A2
B1
B2
A1
A2--B1 A2--A1
B1--B2 A1--B2
Execution LCB4pivot placed above on the right
873.43
Pivot
Wrench 1342 Nm / 31 lbft
Allen wrench 39.8 Nm / 7.2 lbft
Allen wrench 624 Nm / 17.7 lbft
Wrench 13 Wrench 14
NOTE -- The handlever must be ordered separately (see page 9).
SDM102
17DAT011E
-
Anti--shock and anti--cavitation valve
Port relief options
0
10
20
30
0 20 40 60Flow
Pre
ssur
e 300
200
100
(l/min)
(bar)(psi)400
0
100
200
300
400
0 20 40 60Flow
Pre
ssur
e
(l/min)
(bar) (psi)
U175 UT
A B
T
U 175
A B
T
A B
T
UT U175 U175 U175
6 0.24
Wrench 524 Nm / 17.7 lbft
Performance data
Range setting A(B)T Pressure drop TA(B)
Pressure setting in bar
0.17RESPONSE TIME
10%
160
bar
2300
psi90%
95%
105%
Pre
ssur
e
Time ()
(% DP)
Time response
4500
3000
1500
Available on prearranged body.
SDM102
18 DAT011E
-
Port relief valve blanking plug
Anti--cavitation valve
Port relief options
Performance data
C
UT
C UT
A B
T
A B
T
A B
T
UT C C C
3 0.12
Wrench 524 Nm / 17.7 lbft
A B
T
UT UT
5.5
0.22
Wrench 624 Nm / 17.7 lbft
0
10
20
30
0 20 40 60Flow
Pre
ssur
e 300
200
100
(l/min)
(bar)(psi)400
Pressure drop TA(B)
Available on prearranged body.
SDM102
19DAT011E
-
KAE: with full system pressure carry--over
AEK: with closed centre
AE: with carry--over
Outlet conversion port options
A1 B1 A2 B2P
P1
T
T1
Ex.: SDM102/2--P(TG3--175)/513RSLP/18MCSLP/AE--PSC--
1752500
C
A1 B1 A2 B2P
P1
T
T1
1752500
A1 B1 A2 B2P
P1
T
T1
1752500
C
Ex.: SDM102/2--P(TG3--175)/513RSLP/18MCSLP/AEK--PSC--
Ex.: SDM102/2--P(TG3--175)/513RSLP/18MCSLP/KAE--PSC--
20.50.81
26.51.04
Wrench 2442 Nm / 31 lbft
Allen wrench 624 Nm / 17.7 lbft
T
T1
C
T
T1Wrench 2442 Nm / 31 lbft
Allen wrench 624 Nm / 17.7 lbft
Allen wrench 624 Nm / 17.7 lbft
T
T1
C
M12x1.5 DIN906 plugCode: 4TAP312010Allen wrench 6 -- 24 Nm / 17.7 lbft
This option requires special valve body kit; contact Customer Service for more information.
SAE8--G3/8 male--female jointCode: XGIU524552Wrench 24 -- 42 Nm / 31 lbft
20.50.81
SDM102
20 DAT011E
-
Installation and maintenance
The SDM102 valve is assembled and tested as per the technical specification of this catalogue.Before the final installation on your equipment, follow the below recommendations:-- the valve can be assembled in any position; in order to prevent body deformation and spool sticking mount the product on a flat
surface;-- in order to prevent the possibility of water entering the spool control kit, do not use high pressure wash down directly on the valve;-- prior to painting, ensure plastic port plugs are tightly in place.
Carry--over configuration
P
T
C
A1A2
B2
B1
NOTE -- These torque are recommended. Assembly tightening torque depends on many factors, including lubrication, coating andsurface finish. The manufacturer shall be consulted.
SDM102
21DAT011E
Fittings tightening torques -- Nm / lbft
THREAD TYPE P and C ports A and B ports T port
BSP (ISO 228/1) G 3/8 G 3/8 G 3/8With O--Ring seal 35 / 25.8 35 / 25.8 35 / 25.8With copper washer 40 / 29.5 40 / 29.5 40 / 29.5With steel and rubber washer 30 / 22.1 30 / 22.1 30 / 22.1
SAE SAE 8 (3/4--16 UNF) SAE 6 (9/16--18 UNF) SAE 8 (3/4--16 UNF)With o--ring seal 50 / 36.9 30 / 22.1 50 / 36.9
METRIC (ISO 262) M18 x 1.5 M18 x 1.5 M18 x 1.5With O--Ring seal 35 / 25.8 35 / 25.8 35 / 25.8With copper washer 40 / 29.5 40 / 29.5 40 / 29.5With steel and rubber washer 40 / 29.5 40 / 29.5 40 / 29.5
-
SDM102
22 DAT011E
MALFUNCTION CAUSE REMEDY
External leakage control kit or oppositeside.
Worn spool seal due to mechanicalactuation or high back pressure.
Locate the leakage and replace the seal.Check back pressure level.
Excessive internal leakage on A and Bports.
Increase clearance between spools andbody due to high wear
Replace the directional control valve andcheck the oil contamination level.
Dropping load during transition whileraising High leakage on the load check valve.
Remove the load check valve and cleanthe seat.
Inability to build pressure on A and B
Main pressure relief valve blocked open. Remove and clean or replace the mainrelief valve.Inability to build pressure on A and Bports. Port relief valve open.
Remove and clean or replace the portrelief valve.
Low pump pressure and flow. Check the pump and circuit.
Installation and maintenance
Pressure relief valve Spool
Positioner kit
Body
Normally the spools are inter-changeable. Verify the smooth-ness during the assembly
O--Ring seals 15.88x2.62code: 4GUA115926
Chamfer
Load check valvesSealingedge
NOTE -- All articulated parts inside cap, lever box and mechanical joystick are lubricated with synthetic base grease grade NLGI2
Holding O--Ringbushing
-
Master Distributors and Resellers
MALAYSIA POWER FLUIDTRONICS AND SDN BHD.No 12 and 14Seksyen 31, Kota Kemuning40460 Shah Alam Selangortel. 0060 3 5220188fax. 0060 3 5220133
AUSTRALIA SOUTHCOTT PTY.LTDHalifax street G.P.O.B. 10635000 Adelaide S.A.tel. 0061 8 2282411fax. 0061 8 2233413
AUSTRIA RACHER MASCHINEN HYDRAULIKRedlham 1004800 Attnang Puchheimtel. 0043 7674606fax. 0043 7674 606 22
BELGIUM HAGOMATGuldensporenstraat 701800 Vilvoordetel. 0032 2 2521373fax. 0032 2 2512263
DENMARK DANFOSS HYDRAULIK A/SToppevadvej 44--46 GanloesePostboks 429 Stenloese 3660tel. 0045 42 184055fax. 0045 42 184603
FINLAND BERENDSEN PMC OY ABPL 3233901 Tamperetel. 00358 3 31410300fax. 00358 3 2123748
FRANCE FLUIDES TECH. APPLICATIONS6 avenue H. Beaudelet Z.A. de la Gare77330 Ozoir la Ferrieretel. 0033 1 64400029fax. 0033 1 64403288
GERMANY BALSTER HYDRAULIK G.m.b.H.Postfach 11014144057 Dortmundtel. 0049 231 590021fax. 0049 231 592645
NOLD HYDRAULIK+PNEUMATIK G.m.b.H.Enzisreute88339 Bad Waldseetel. 0049 7524 97200fax. 0049 7524 972070
RAUH HYDRAULIK G.m.b.H.Hallstadter strasse 6396052 Bambergtel. 0049 951 966360fax. 0049 951 9663699
TH. NIEHUES G.m.b.H.Bahnhofstrasse 8148308 Senden, Bosenselltel. 0049 2536 99001fax. 0049 2536 99019
GREECE C. PARIS & CO. O.E.53 Marathonomachon str.akad10441 Platonos, Athenstel. 0030 1 5135701fax. 0030 1 5144579
CANADA CANIMEX INC.285 St. Georges J2C 4H3Drummondville Quebectel. 001 819 477 1335fax. 001 819 477 2908
HOLLAND ABS HYDRAULICS B.V.Lloydsweg 8P.O.B. 69641 KK Veendamtel. 0031 598 6 22544fax. 0031 598 6 20875
KAVEE HYDRAULICSAaltenseweg 62Postbus 1497050 AC Varsseveldtel. 0031 315 254111fax. 0031 315 244401
TECHNISCH CENTRUM GROOT B.V.Winkelerzand 3P.O.B. 11731 LZ Winkeltel. 0031 224 544444fax. 0031 224 544433
ICELAND LANDVELAR EHFSmiojuvegur 66P.O. box 20200 Kopavogurtel. 00354 557 6600fax. 00354 557 8500
ITALY CONSUL FLUID S.A.Sdi Plicchi Fabio & C.via Luciano Romagnoli 2740069 Zola Predosa, Bolognatel. 0039 051 6167474fax. 0039 051 6167411
FER HYDRAULIK S.R.Lvia Lambrakis 16--16/A42100 Reggio Emiliatel. 0039 0522 332177fax. 0039 0522 553891
OLEODINAMICA GAMBINI S.R.L.Strade Cattane 836100 Vicenzatel. 0039 0444 962030fax. 0039 0444 961993
OLEODINAMICA GIANNINI S.R.L.via Arno 1350019 Osmannoro, Firenzetel. 0039 055 374691fax. 0039 055 300290
OLEOMEC S.R.L.via Divisione Acqui61027 Villa Fastiggi, Pesarotel. 0039 0721 281861fax. 0039 0721 281825
OLEO MECCANICA INDUSTRIALECOMPONENTI S.R.L.via Nenni 220060 Bussero, Milanotel. 0039 02 95330080fax. 0039 02 95330090
PARMAFLUID S.R.L.via Azzoni 9/A43100 Parmatel. 0039 0521 480711fax. 0039 0521 480750
RVS DI CAVIASSO A. & C. S.A.S.via Macedonia 2410097 Collegno, Torinotel. 0039 011 4031333fax. 0039 011 4031479
ISRAEL L.Y.A. CO. LTD105 Hahashmonaim st.67011 Tel Avivtel. 00972 3 5611712fax. 00972 3 5613250
KOREA TOKIMEC KOREA HYDRAULICS CO. LTDLG Bldg 5F152 055 Guro--Dong, Guro--Gu, Seoultel. 0082 2 630 5850fax. 0082 2 630 5859
NORWAY LAUTOM ASHauger Skolevei 181351 Rudtel. 0047 67 178300fax. 0047 67 178305
PORTUGAL GUSTAVO CUDELL LDAR.Eng.Ferreira Dias 9544100 Oportotel. 00351 2 6102004fax. 00351 2 6158010
MOVICONTROL LDARua Prof.Henrique de Barros 5AP2685 Prior velhotel. 00351 1 9429900fax. 00351 1 9413500
SINGAPORE FLO--LINE HYDRAULICS PTE LTD47 Joo koon circleSingapore 629067tel. 0065 8632 022fax. 0065 8631 825
SOUTH AFRICAHYFLOSouthern Africa ltdP.O. box 240 Paarden eiland 7420tel. 0027 21 511 7021fax. 0027 21 5114456
LOWE ERNEST6 Skew road1460 Boksburg Northtel. 0027 11 8944281fax. 0027 11 8946108
SWEDEN HYDRAC ABGetaengsvaegen 2250263 Borastel. 0046 33 127470fax. 0046 33 125879
SPAIN INTERSEAL S.A.Autovia de Castelldefels Km 508820 El prat de Llobregat Barcelonatel. 0034 93 3706711fax. 0034 93 3701807
SWITZERLANDBT HYDRAULIK AGFischermattelistrasse 63000 Berna 5tel. 0041 31 3798141fax. 0041 31 3823980
TAIWAN LIMIT TEIN INDUSTRIAL CO. LTD2F. NO. 8--1 lane 42 sec.3TZU Ching rd. Sanchung cityTaipei Hsientel. 00886 2 9995022fax. 00886 2 9995055
THAILAND SRITONG ENGINEERING CO. LTD8/233--236 Moo 4 Rama 210150 Bangmod chomthong, Bangkoktel. 00662 428 4171fax. 00662 428 4180
TURKEY HIDRO KONTROL MAK. SANAYI VE TIBuyuk Sanayi 1 Cadde Arpacio 2Ishani n. 95/11 Iskitler6060 Ankaratel. 0090 312 3842895fax. 0090 312 3414476
HIDROTAS DIS TICARET A.S.Halit Ziya bulv n.33Zuhal is han--Izmirtel. 0090 232 4842253fax. 0090 232 4837463
UNITED KINGDOMBYPY HYDRAULICS &TRANSMISSIONS LTDNO. 8 Lingen road sheet R.I.E.Ludlow salop sy8 1xdtel. 0044 1 584 873012/3/4fax. 0044 1 584 876647
USA MC ELROY FLUID POWER826 North Fulton74158 Tulsa Oklahomatel. 001 918 8369055fax. 001 918 8319300
CHINA DRENNAN COMPANY LTD.2111 Wing on House71 Des Voeux Road CentralHong Kongtel. 00852 2817 3523fax. 00852 2817 3735
INDIA METTERS PRIVATE LT.144 St. Johns Church Rd.Bangalore 560 005tel. 0091 080 554 2949fax. 0091 080 555 5064
IRELAND NELSON HYDRAULICS LTDUnit 54, Cookstow Ind. EstateTallaght Dublin 24 jtel. 00353 1 4510 622fax. 00353 1 4510 893
MOROCCO MECOMAR S.A.7 Rue Abdelwahed el MarrakchiOukacha, Casablancatel. 00212 2 661550--1--2fax. 00212 2 661555
NEW ZELAND VICKERS SYSTEMS LTD77--79 Ben Lomond CrescentP.O.Box 51 076 PakurangaAouklandtel. 0064 9 576 9089fax. 0064 9 576 5865
POLAND IOW POLSKAU.L. Brukselska 103973 Warszawatel. 0048 22 6161313fax. 0048 22 6178485
TUNISIA AFRICA INDUSTRIEN.Z.I Ben ArousTunistel. 0021 61 1 384510fax. 0021 61 1 384476
-
WALVOIL S.P.A.
42100 REGGIO EMILIA ITALY VIA ADIGE, 13/DTEL. +39.0522.932411 FAX +39.0522.300984
E--MAIL: [email protected] HTTP: //WWW.WALVOIL.COM
CUSTOMER SERVICE
TEL. +39.0522.932555 FAX +39.0522.932455
D1409808IDAT011E