CONGRATULATIONS ON YOUR PURCHASE OF OUR PATENTEDUS Patent No. 7437794

REALLY EZ MAGNETIC DUCT SCRAPERTM

The time and money you SAVE using it will astound you!

INSTRUCTION GUIDE ATTACHED

PLEASE READ AND FOLLOW ALL INSTRUCTIONS BEFOREAND WHILE USING.

• Do not use scraper unless all instructions are understood thoroughly.

• Do not use for other than intended use.• Before every use, make sure that machined bolts and screws are secured tightly on Jiffyloc pole and on scraper.Use scraper with Jiffyloc extension poles only - safetychain and safety clip must be attached.

CAUTION: VERY STRONG MAGNETS IN BOTTOMOF SCRAPER WILL ATTRACT ALL MAGNETICMETAL – USE WITH CARE!

We suggest you purchase a toolbox to store your scrapers, blades, andprotective pans in for convenience, as well as for safety.

Limited Warranty

Guardian Power Cleaning Corp. warrants to the original consumer purchaser, and solely for the benefit of such originalconsumer purchaser (hereinafter referred to as the “consumer”), that the patented (US Patent No. 7437794) Really EZMagnetic Duct ScraperTM, is free of defects in materials and workmanship for a period of ninety (90) days from the dateof purchase, as long as such consumer only properly uses the Really EZ Magnetic Duct ScraperTM.Guardian Power Cleaning Corp. (GPCC) will correct defects in the Really EZ Magnetic Duct ScraperTM by repair or replace-ment, at its option. A return authorization is required prior to shipping the Really EZ Magnetic Duct ScraperTM to GPCCat 800-735-5002. Only after an analysis and review by GPCC’s Quality Control dept. and the Really EZ Magnetic DuctScraperTM is deemed covered under the Limited Warranty, as outlined above, will a repair or replacement be issued.

Failure to comply with instructions could result in personal injury and/or property damage. GPCC assumes no liabilityfor any incidental or consequential damages from misuse or translation interpretation of these instructions.

Please be sure to visit us on the web @ www.ductscraper.com

Figure 1

Figure 2

REMOVING SCRAPER FROM PAN:-Place scraper with pan on floor (note position of let-tering on scraper) with straight edge of pan towardyou and 45 degree angle of pan away from you-Place workboot on foot pad as shown, to keep panfrom moving-Push handle of scraper forward and away fom youwhile lifting scraper out of pan

REPLACING SCRAPER INTO PAN:-Place pan on floor and hold handle as shown in arigid position and guide scraper into the angle areaof the pan-Magnet will pull scraper down, into the pan

CAUTION:VERY SHARP RAZOR BLADES

VERY STRONG MAGNETS

SCRAPER IS ALUMINUM–DO NOT SOAK IN

CORROSIVE CHEMICAL!!!

IMPORTANT NOTETo remove scraper from the duct, twist the handle to the left or right. DO NOT pull the scraper off the duct,

TWIST IT OFF!

Figure 3

Figure 4

Aluminum bar removed onlyto show final placement of

the razor blade

TO INSTALL/REMOVE RAZOR BLADES:Place scraper on a flat, non-magnetic surface, and extendscraper past the end of flat surfaceso the blade can be held as shown.Use thumbscrews to loosen forremoval or tighten to install blades.No need to remove aluminum barsholding razor blades in place.Loosen thumb screws just enoughto slip the razor blade in place asshown.

MAKE SURE THUMB SCREWS ARETIGHTENED DOWN ALL THE WAYAND BLADES ARE SECURE,USING PLIERS IF NECESSARY.

ATTACHING SAFETY CHAIN TO THE JIFFYLOC POLE:

The handle is designed to work EXCLUSIVELY with the

“Jiffyloc” extension pole, which uses a positive quick

connect/disconnect system, making use of the

“Really EZ Magnetic Duct Scraper” a

SNAP!We have specifically designed a chain from the “Jiffyloc”

pole to the “Really EZ Magnetic Duct Scraper” which will

perform a dual function – first for safety and second for

retrieval if pole separates from scraper

Figure 5

-Loosen the (2) phillips-head screws from the female threaded top portion of the pole andunscrew it-Attach chain onto split ring and slip ring over male thread section pf pole as shown-Replace the female threaded top portion of the pole onto the male threaded portion, screw itdown to the base by hand, and tighten the (2) phillips-head screws-See Figure 6, next page, for connecting opposite ends of chain to the scraper

lVery

Important

SAFETY CHAIN AND SAFETY CLIP MUST BE ATTACHEDWHEN USING JIFFYLOC EXTENSION POLE!

Before every use, make sure that all of the machined bolts and screws are secured tightly on the Jiffyloc pole and on the Really EZ Magnetic Duct Scraper

IMPORTANT NOTES• DO NOT soak scraper or

Jiffyloc poles in corrosive chemical.• When using scraper from above,

make certain there is nobody below the duct.

Figure 6

-Attach the opposite end of the chain tothe split ring on the scraper

lVery

Important

Safety Clip

Figure 7

Figure 8

-Place scraper on interior wallof vertical or horizontal greaseduct and scrape away

-Be aware of any screws and irregularitiesin the ductwork as you scrape

Able to scrape long ducts to bare metal in a fraction of the time compared

to traditional methods!

EZ, Quick cleanup!

And they said there wasn’t anything new under the sun!!!

See it on our website:

www.ductscraper.com