sanitary elbow (1 and # of ##) rev ##04 · the sanitary elbow thermowell can be manufactured with...
TRANSCRIPT
Contents Illustrations
FORM 080036808/06
Sanitary Elbowwith Built-In Thermowell
Installation Manual
For Sanitary Elbow Themowells Ordering Information please reference Burns Engineering Series ‘S’ Catalog, Type SWE Elbow Thermowells
While this information is presented in good faith and is believed to be accurate, Burns Engineering cannot guarantee satisfactory results from reliance upon this information.
Sanitary Elbow with Built-In Thermowell Installation Manual
Top View
Front View
0
180
90 270
Side View
Line Slope
Concentric StyleSanitary Elbow Thermowells
0
180
90 270
Front View
Top View
Side View
Line Slope
0
180
270 90
Front View
Top View
Side View
Line Slope
Front View
Top View
270
90
0
Side View
180
Line Slope
Front View
Top View
90
270
0 180
Side View
Eccentric StyleSanitary Elbow Thermowells
(270° Reducer Orientation (D))
Line Slope
2
Concentric Elbow (fig. a) 20° Orientation Elbow (fig. b) 290° Orientation Elbow (fig. c) 2180° Orientation Elbow (fig. d) 2270° Orientation Elbow (fig. e) 2
Introduction 1Installation 1
Figure a. Concentric Elbow Figure b. 0° Orientation Elbow
Figure c. 90° Orientation Elbow Figure d. 180° Orientation Elbow
Figure e. 270° Orientation Elbow
Introduction The sanitary elbow thermowell is designed to provide a way to make temperature measurements in small diameter lines without impeding the process flow or inducing errors due to stem conduction. For lines less than 1” in diameter, the thermowell tubing diameter is increased around the well to accommodate flow with minimal restriction. The parallel orientation of the well allows for greater sensor immersion which minimizes stem conduction effects.
Installation Identify the inlet and outlet of the sanitary elbow thermowell and align to the process flow direction.
For lines less than 1” in diameter, the inlet orientation needs to be considered. The orientation should be such that no fluid is trapped when the line is drained. Choose the appropriate orientation from
Eccentric StyleSanitary Elbow Thermowells(90° Reducer Orientation (B))
Eccentric StyleSanitary Elbow Thermowells(0° Reducer Orientation (A))
Eccentric StyleSanitary Elbow Thermowells
(180° Reducer Orientation (C))
Burns Engineering Inc. 10201 Bren Road East Minnetonka, Minnesota 55343 For assistance call 800-328-3871 952-935-4400
Notes:
Burns Engineering Inc. www.burnsengineering.com
Fig. a-e according to the line placement and line slope.
The sanitary elbow thermowell can be manufactured with weld ends to be butt welded in place or with tri-clover ends to be clamped in place. If ordered with weld ends, use an orbital welder to connect thermowell to the existing lines. If ordered with tri-clover ends, connect to the existing lines with the appropriate gaskets and clamps.
The sanitary elbow thermowell can be manufactured with a threaded or tri-clover instrument connection. If ordered with a threaded instrument connection, install spring-loaded element into well using the wrench flats for leverage (do not over tighten). If ordered with a tri-clover instrument connection, install spring-loaded element using the appropriate gasket and clamp.
Inlet
Out
let
Inlet
Out
let
Inlet
Out
let
Inlet
Out
let
Inlet
Out
let
Contents Illustrations
FORM 080036808/06
Sanitary Elbowwith Built-In Thermowell
Installation Manual
For Sanitary Elbow Themowells Ordering Information please reference Burns Engineering Series ‘S’ Catalog, Type SWE Elbow Thermowells
While this information is presented in good faith and is believed to be accurate, Burns Engineering cannot guarantee satisfactory results from reliance upon this information.
Sanitary Elbow with Built-In Thermowell Installation Manual
Top View
Front View
0
180
90 270
Side View
Line Slope
Concentric StyleSanitary Elbow Thermowells
0
180
90 270
Front View
Top View
Side View
Line Slope
0
180
270 90
Front View
Top View
Side View
Line Slope
Front View
Top View
270
90
0
Side View
180
Line Slope
Front View
Top View
90
270
0 180
Side View
Eccentric StyleSanitary Elbow Thermowells
(270° Reducer Orientation (D))
Line Slope
2
Concentric Elbow (fig. a) 20° Orientation Elbow (fig. b) 290° Orientation Elbow (fig. c) 2180° Orientation Elbow (fig. d) 2270° Orientation Elbow (fig. e) 2
Introduction 1Installation 1
Figure a. Concentric Elbow Figure b. 0° Orientation Elbow
Figure c. 90° Orientation Elbow Figure d. 180° Orientation Elbow
Figure e. 270° Orientation Elbow
Introduction The sanitary elbow thermowell is designed to provide a way to make temperature measurements in small diameter lines without impeding the process flow or inducing errors due to stem conduction. For lines less than 1” in diameter, the thermowell tubing diameter is increased around the well to accommodate flow with minimal restriction. The parallel orientation of the well allows for greater sensor immersion which minimizes stem conduction effects.
Installation Identify the inlet and outlet of the sanitary elbow thermowell and align to the process flow direction.
For lines less than 1” in diameter, the inlet orientation needs to be considered. The orientation should be such that no fluid is trapped when the line is drained. Choose the appropriate orientation from
Eccentric StyleSanitary Elbow Thermowells(90° Reducer Orientation (B))
Eccentric StyleSanitary Elbow Thermowells(0° Reducer Orientation (A))
Eccentric StyleSanitary Elbow Thermowells
(180° Reducer Orientation (C))
Burns Engineering Inc. 10201 Bren Road East Minnetonka, Minnesota 55343 For assistance call 800-328-3871 952-935-4400
Notes:
Burns Engineering Inc. www.burnsengineering.com
Fig. a-e according to the line placement and line slope.
The sanitary elbow thermowell can be manufactured with weld ends to be butt welded in place or with tri-clover ends to be clamped in place. If ordered with weld ends, use an orbital welder to connect thermowell to the existing lines. If ordered with tri-clover ends, connect to the existing lines with the appropriate gaskets and clamps.
The sanitary elbow thermowell can be manufactured with a threaded or tri-clover instrument connection. If ordered with a threaded instrument connection, install spring-loaded element into well using the wrench flats for leverage (do not over tighten). If ordered with a tri-clover instrument connection, install spring-loaded element using the appropriate gasket and clamp.
Inlet
Out
let
Inlet
Out
let
Inlet
Out
let
Inlet
Out
let
Inlet
Out
let