sandvik de140 compact core drill - causa.com.mx · 76 1323 m (4340 ft) 1323 m (4340 ft) h not...
TRANSCRIPT
Sandvik DE140 compact core drill
Technical specificaTion
The DE140 is a compact and powerful drill rig that has
been design to meet requirements for deeper and larger
holes without compromising the size. DE140 features a pull
and push capacity of 10 tones. DE140 has a MaxTorque
control and direct feed and is well suited for surface and
underground exploration drilling, geotechnical drilling and
medium diameter raise boring. DE140 for underground
use is powered by either a 55 kW or 90 kW Power Unit.
For surface use 92 kW or 147 kW Diesel Power Packs. The
MaxTorque control enables optimal balance of torque and
rotation speed.
Main specification - DE140Type Fully hydraulic core drill
Rotation unit Drill head with chuck
Feed force 92,2 kN 20 730 lbf
Pull force 92,2 kN 20 730 lbf
Lift capacity, max* 1592 m (B) 5223 ft (B)
Feed length** 1 700 mm 5’7’’
Weight(including feed boom, drill
head 77 mm, rod holder
and mounting bracket)
695 kg*695 kg**
1 530 lb*1 530 lb**
DE140 TS 002ENG/2011
*Lift capacity is based on feedback from field operatives and can be reasonably expected with
vertical, water filled holes, by a well-trained drilling crew using high quality drilling tools. Sandvik
cannot guarantee that these results will be achieved in all drilling conditions.
**Underground version
***Surface version
Vertical downDrill rod “N”-head “H”-head
46 2473 m (8114 ft) Not suitable
A 2000 m (6562 ft) Not suitable
56 1918 m (6293 ft) 1918 m (6293 ft)
B 1592 m (5223 ft) 1592 m (5223 ft)
66 1843 m (6047 ft) 1843 m (6047 ft)
N 1220 m (4003 ft) 1220 m (4003 ft)
76 1323 m (4340 ft) 1323 m (4340 ft)
H Not suitable 830 m (2723 ft)
103 Not suitable 895 m (2936 ft)
lifT capaciTy
Lift capacity is based on feedback from field operatives and
can be reasonably expected with vertical, water filled holes,
by a well-trained drilling crew using high quality drilling
tools. Sandvik cannot guarantee that these results will be
achieved in all drilling conditions.
Practical up-drilling capacity is about 50% of capacity in
holes vertical down.
Drill uniT
feed boom
Standard version is made of very stiff and torsion resistant
steel profile. The feed boom is mounted on a frame with
hydraulic tilt cylinder and mechanical supports.
The new type of hydraulic feed cylinder from Sandvik gives
the drill a very high push and pull capacity in relation to its
size.
The mounting frame for the underground version is spe-
cially designed for easy setting-up when fan drilling and has
a full range adjustment from vertical down to vertical up.
Positioning is simplified by a mechanical feed boom posi-
tioner allowing a telescoping of 1 - 2 m (3 - 6’) depending
on feed boom length.
Feed boomBasic facts - feed boomFeed length* 1 700 mm (5’7’’)
Total length* 3 018 mm (10’)
Feed force 92,2 kN (20 730 bf)
Pull force 92,2 kN (20 730 lbf)
Feed speed, rod running, max 0,6 m/s (24’’/s)
*Underground version
rod holder
The Rod holder closes automatically by the gas accumulator
and opens hydraulically. Rod holder and Chuck work with
inverted action which means that the Rod holder opens
when the Chuck closes and vice versa (except for “Big
Jaw”). Exchangeable rod guides and jaws for standard drill
rods, casing and core barrels.
Standard Compact ”Big Jaw”Function Closes by means of
accumulator, opens hydraulically
Closes by means of cup springs, opens hydrauli-cally
Closes and opens hydraulically
Number of jaws 2 2 2
Gripping range 30-106 mm(1 3/16’’-4 1/8’’)
37-80 mm(1 15/32’’-3 5/32’’)
36-150 mm(1 27/64’’-5 29/32’’)53-300 mm(2 3/32’’-11 13/16’’)
Gripping range / set of jaws
20 mm(3/4’’)
18 mm(23/32’’)
87 mm(3 7/16’’)
Max opening without jaws
136 mm(5 5/16’’)
89 mm(3 1/2’’)
150 mm / 300(5 29/32’’ / 11 13/16’’)
rotation unit
N-head 77 mm spindle (3”)
H-head 103 mm spindle(4 1/16”)
Hydraulic motor 60 cc motor 60 cc motor 80 cc motorTorqueHigh gear 236 Nm at 1600 rpm (137 lbf ft)
552 Nm at 776 rpm (427 lbf ft)343/709* Nm at 1100 rpm937 Nm at 460 rpm
343/709* Nm at 1100 rpm 1249 Nm at 345/625* rpm
Low gear 342 Nm at 1100 rpm (200 lbf ft)801 Nm at 535 rpm (619 lbf ft)
Rotation speed 0-2 000 rpm 0-1250 rpm 0-1250 rpm
No. of jaws 8 12 12
Gripping range 30-76 mm (1 3/16’’-3’’) 38-102 mm (1 31/64’’-4 1/64’’)
38-102 mm(1 31/64’’-4 1/64’’)
Gripping range / set of jaws
10 mm (3/8’’) 15 mm (19/32’’) 15 mm (19/32’’)
Speed is infinitely variable between zero – max rpm.
Chuck is closed by spring action and opened hydraulically.
Exchangeable rod guides and jaws for standard drill rods
and casing.
A high torque assembly is available for the N-head for cases
where extra high torques are required. The rpm can be
varied between 0 and 280 rpm and gives a maximum torque
of 1900 Nm.
* Requires MaxTorque panel and 90 kW (123 hp) electric or 147 kW (200 hp) diesel Power pack.
Rod holder Standard
Rotation unit
control panel
Central control of all drilling operations, incl flush pump,
wireline hoist and boom tilt. The hydraulic panel is avail-
able in two versions:
• Standard for 55 kW electric (75 hp) 92 kW diesel (125 hp)
• MaxTorquefor90kWelectric(123hp)
147 kW diesel (200 hp)
Gauges for
• hydraulic system pressure
• feeding force
• water pressure
• water flow
”rod runner” – rod running panel
The panel weighs 3 kg (6,6 lb), is mounted on a tripod and
can easily be moved to a suitable position in the vicinity of
the drill. From the “ROD RUNNER” the operator controls
the rod running up and down the hole as well as make up of
the rods. Especially suited for one-man operations.
Control Panel Max Torque Control Panel Standard
“ROD RUNNER”
opTions
Wireline hoist
There are four wireline hoist options. All hoists work
hydraulically and are operated from the control panel.
Wireline mast
With rod support and sheave wheel for wireline rope.
Available in Standard and Heavy Duty versions where the HD
version consists of a sheave wheel in combination with
1 meter modules to desired length. Standard mast in picture.
Drum- capacity
800 m x 5 mm wire(2 625’x13/64’’)600 m x 6 mm wire (1972’x15/64’’)
1 200 m x 5 mm wire(3 945’x13/64’’)800 m x 6 mm wire2625’x15/64’’)
1 200 m x 5 mm wire(3 945’x13/64’’)
800 m x 6 mm wire2 625’x15/64’’)
Cable leveller
No No Yes Yes
Pulling force Empty drum 12 kN (2 700 lbf)
Empty drum 12 kN (2 700 lbf)
Empty drum 12 kN (2 700 lbf)
Empty drum 12 kN (2 700 lbf)
Speed full drum 2,7 m/s (9’/s) 2,7 m/s (9’/s) 2,7 m/s (9’/s) 2,7 m/s (9’/s)
Sheave wheel Compl. mast (UG) Compl. mast (S)
Standard 640 mm (26’’) 1 000 mm (40’’) 2 000 mm (80’’)
Heavy Duty 700 mm (28’’) 1 000 mm modules (40’’) 1 000 mm modules (40’’)
WL Mast
WL Hoist
flush pumps
Triplex Flush pumps are suitable for water and light
polymer mud only. Alternative power sources: Hydraulic,
electric or diesel. Hydraulic option enables operation from
control panel.
power unit
Apart from the standard power units below, we can meet
most requirements from the customers.
capacity Up to 150 l/min (40 gpm)
pressure, max Up to 100 bar (1450 psi)
Underground Surface
Motor55 kW (75 hp) electric, Class F, IP56-IEC144, Overheat protection
90 kW (120 hp) electric, Class F, IP56-IEC144, Overheat protection
92 kW (123 hp) diesel Six cylinder turbo diesel motor
147 kW (200 hp) diesel Six cylinder turbo diesel motor
Power data
55 kW, 50 Hz, 1470 rpm, 380 V62 kW, 60 Hz, 1760 rpm, 440 V
90 kW ,50 Hz, 1450 rpm, 380 V108 kW, 60 Hz, 1760 rpm, 440 V
92 kW at 1800 rpm 147 kW at 1500 rpm
Max working pressure 250 bar (3625 psi) 250 bar (3625 psi) 250 bar (3625 psi) 250 bar (3625 psi)
Max oil flow 145 l/min (38 gpm) 270 l/min (71 gpm) 230 l/min (61 gpm) 275 l/min (74 gpm)
Tank volyme 80 liter (21 usg) 200 liter (53 usg) 80 liter (21 usg) 200 liter (53 usg)
Cooler Water Water Water Water
Other info.
Y/D connector, Oil level indicator, Filter indicator, Thermometer, Hand pump for oil fill, Pressure and return filter
Y/D connector, Oil level indicator, Filter indicator, Thermometer, Hand pump for oil fill, Pressure and return filter, Sound isolation
Oil level indicator, Filter indicator, Thermometer, Hand pump for oil fill, Pressure and return filter
Oil level indicator, Filter indicator, Thermometer, Hand pump for oil fill, Pressure and return filter
Control Panel Standard panel MaxTorque-panel Standard panel MaxTorque-panel
Dimensions anD WeighTs
Dimensions
Drill unit mm inch Mounting frame mm inch
Feed length 1710 67
A 4465 176 F 1 240 49
B 3390 133 G 880 35
C 3250 128
D 1140 45
E 650 26
Power unit
55 kW (75 hp) 90 kW (120 hp)mm inch mm inch
I 1600 63 3160 124
K 1430 56 1850 73
L 860 34 1225 48
M 1040 41 1600 63
N 840 33 1175 46
Control panel, standard Control panel, MaxTorque
mm inch mm inch
O 1 165 46 O 1165 46
P 480 19 P 480 19
R 525 21 R 600 24
Weights
Underground Surface
kg lb kg lb
Drill unit; incl feed boom, rotation unit 77 mm, rod holder and mounting bracket
695 1530 695 1530
D:o with 103 mm rotation unit 847 1867 847 1867
Mounting frame with tilt cylinder and support legs 200 440 225 495
Power unit 55 kW 640 1411
Power unit diesel 92 kW 920 2028
Power unit electrical 90 kW 1050 2315
Power unit diesel 147 kW 1380 3042
Hydraulic hoses 80 176 80 176
Control panel 110 242 110 242
Control panel MaxTorque 122 269 122 269
Wireline hoist 1200 m excl. rope 107 236 107 236
Wireline mast 1000 mm 40 88
Wireline mast 2000 mm 50 110
feed boom positioning
Working area, min/max
This equipment is constantly liable to review and improvement and no responsibility can be accepted for subsequent modifications making
all or part of these specifications obsolete. Sandvik reserves the right to change these specifications without prior notice.
Measurement range* mm inch
A 4250 167
B 3500 138
C 1900 75
D 2100 83
E 3750 148
*Working range for DE140 with feed boom.
Note: The picture shows the working range of the core drilling rig without the wireline mast mounted. With the mast and sheave wheel mounted, the mea-surements at A and B should be adjusted.
SANDVIK MINING AND CONSTRUCTION • www.sandvik.com ® S
AN
DV
IK is
a r
egis
tere
d tr
adem
ark
owne
d by
San
dvik
Com
pani
es in
Sw
eden
and
oth
er c
ount
ries
. © 2
011
SAN
DV
IK
Sandvik is a high-technology engineering group with
world-leading positions in selected areas – tools for metal
working, advanced materials technology, and mining and
construction. We are represented in 130 countries.
Sandvik Mining and Construction represents one third of
the overall Sandvik Group and serves a broad range of
customers in construction, mineral exploration, mining
and bulk materials handling. Our construction expertise
covers quarrying, tunneling, demolition and recycling, and
other civil engineering applications. Our mining products
and services support customers on the surface and under
ground, in all mineral, coal and metal mining applications
from exploration to ore transportation.