sample - total training supporttotaltrainingsupport.com/samples/17.1 fundamentals (landscape... ·...

Module 17 Propeller

Module 17A and 17B Licence Category A, B1 and B3

Propeller

17.1 Fundamentals

Copyright 2014 © Total Training Support Ltd Module 17.1 Fundamentals

Sample

Module 17 Propeller Copyright Notice © Copyright. All worldwide rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form by any other means whatsoever: i.e. photocopy, electronic, mechanical recording or otherwise without the prior written permission of Total Training Support Ltd. Knowledge Levels — Category A, B1, B2, B3 and C Aircraft Maintenance Licence Basic knowledge for categories A, B1, B2 and B3 are indicated by the allocation of knowledge levels indicators (1, 2 or 3) against each applicable subject. Category C applicants must meet either the category B1 or the category B2 basic knowledge levels. The knowledge level indicators are defined as follows: LEVEL 1

• A familiarization with the principal elements of the subject.

Objectives: • The applicant should be familiar with the basic elements of the

subject. • The applicant should be able to give a simple description of the

whole subject, using common words and examples. • The applicant should be able to use typical terms.

LEVEL 2

• A general knowledge of the theoretical and practical aspects of the subject.

• An ability to apply that knowledge.

Objectives: • The applicant should be able to understand the theoretical

fundamentals of the subject.

• The applicant should be able to give a general description of the subject using, as appropriate, typical examples.

• The applicant should be able to use mathematical formulae in conjunction with physical laws describing the subject.

• The applicant should be able to read and understand sketches, drawings and schematics describing the subject.

• The applicant should be able to apply his knowledge in a practical manner using detailed procedures.

LEVEL 3

• A detailed knowledge of the theoretical and practical aspects of the subject.

• A capacity to combine and apply the separate elements of knowledge in a logical and comprehensive manner.

• Objectives:

• The applicant should know the theory of the subject and interrelationships with other subjects.

• The applicant should be able to give a detailed description of the subject using theoretical fundamentals and specific examples.

• The applicant should understand and be able to use mathematical formulae related to the subject.

• The applicant should be able to read, understand and prepare sketches, simple drawings and schematics describing the subject.

• The applicant should be able to apply his knowledge in a practical manner using manufacturer's instructions.

• The applicant should be able to interpret results from various sources and measurements and apply corrective action where appropriate.


Sample

Module 17 Propeller Module 17.1 Enabling Objectives and Certification Statement Certification Statement These Study Notes comply with the syllabus of EASA Regulation (EC) No.2042/2003 Annex III (Part-66) Appendix I, as amended by Regulation (EC) No.1149/2011, and the associated Knowledge Levels as specified below:

Objective Part-66 Reference

Licence Category A B1 B3

Fundamentals 17.1 1 2 2 Blade element theory; High/low blade angle, reverse angle, angle of attack, rotational speed;

Propeller slip; Aerodynamic, centrifugal, and thrust forces;

Torque; Relative airflow on blade angle of attack;

Vibration and resonance.


Sample

Module 17 Propeller Table of Contents Chapter 17.1 Fundamentals ____________________________ 6

Introduction _______________________________________ 6

Propulsive Force ___________________________________ 6

Propeller Terms ____________________________________ 8

Effective Pitch, Geometric Pitch and Slip ______________ 10

Angle of Attack ____________________________________ 12

Propeller Configuration _____________________________ 11 Pusher _______________________________________________14 Tractor _______________________________________________14 Contra-Rotating ________________________________________16 Counter-Rotating _______________________________________16

Propeller Solidity __________________________________ 16

Propeller Clearances _______________________________ 18

Right and Left Handed Propellers ____________________ 20

The Blade Element _________________________________ 20

Blade Angle and Blade Pitch ________________________ 22

Blade Twist _______________________________________ 22

Forces on a Blade Element __________________________ 24

Variation of Propeller Efficiency with Speed ____________ 26

Windmilling _______________________________________ 26

Feathering ________________________________________ 28

Reverse Thrust ____________________________________ 28

Forces Acting on the Propeller _______________________ 28 Centrifugal Force _______________________________________28

Thrust Bending Force ___________________________________ 30 Torque Bending Force___________________________________ 30 Aerodynamic Twisting Moment (ATM) ______________________ 32 Centrifugal Twisting Moment (CTM) ________________________ 32 Turning Moments in the Windmill Condition __________________ 32

Pitch Range ______________________________________ 34

Handling Effects - Single Engine Aircraft ______________ 36 Asymmetric Effect (P-Factor) _____________________________ 36 Slipstream Effect _______________________________________ 36 Torque Reaction _______________________________________ 36 Gyroscopic Effect ______________________________________ 38

Thrust and Power Development ______________________ 40 Power Development in Piston Engines ______________________ 40 Power Development in Turboprop Engines __________________ 40

Turboprop Configurations __________________________ 43

Vibrational Forces and Resonance _____________________ 44

Glossary _________________________________________ 47


Sample

Module 17 Propeller

Intentionally Blank


Sample

Module 17 Propeller

Chapter 17.1 Fundamentals Introduction Throughout the development of controlled flight as we know it, every aircraft required some kind of device to convert engine power to some form of thrust. Nearly all of the early practical aircraft designs used propellers to create this thrust. As the science of aeronautics progressed, propeller designs improved from flat boards, which merely pushed the air backwards, to aerofoil shapes. These aerofoils produced lift to pull the aircraft forward through aerodynamic action. As aircraft designs improved, propellers were developed which used thinner aerofoil sections and had greater strength. Because of its structural strength, these improvements brought the aluminium alloy propeller into wide usage. The advantage of being able to change the propeller blade angle in flight led to wide acceptance of the two-position propeller and, later, the constant speed propeller system. Today, propeller designs continue to be improved by the use of new composite materials, new aerofoil shapes and multi blade configurations. Propulsive Force A propeller is a means of converting engine power into propulsive force. A rotating propeller imparts rearward motion to a mass of air and the reaction to this is a forward force on the propeller blades.

A propeller moves a large mass of air rearward, at a relatively slow speed, as opposed to a gas turbine engine, which moves a small mass of air rearward at a high speed.

Thrust = Mass(Vo – VI)


Sample

Module 17 Propeller

Figure 1.1: Thrust from a propeller

Figure 1.2: Blade Terms


Sample

Module 17 Propeller Propeller Terms Before starting any discussion about propellers, it is necessary to define some basic terms to avoid confusion and misunderstanding. A propeller is a rotating aerofoil that consists of two or more blades attached to a central hub which is mounted on the engine crankshaft. The function of the propeller is to convert engine power to useful thrust. Propeller blades have a leading edge, trailing edge, a tip, a shank, a face, and a back. Blade angle is the angle between the propeller’s plane of rotation, and the chord line of the propeller aerofoil. Blade station is a reference position on a blade that is a specified distance from the centre of the hub. Pitch is the distance (in inches or millimetres) that a propeller section will move forward in one revolution. Pitch distribution is the gradual twist in the propeller blade from shank to tip.


Sample

Module 17 Propeller

Figure 1.3: Blade Terms


Sample

Module 17 Propeller Effective Pitch, Geometric Pitch and Slip Since the angle of a propeller blade varies along its length, a particular blade station must be chosen to specify the pitch of a blade. Rather than using blade angles at a reference station, some propeller manufacturers express pitch in inches at 75% of the radius. This is the geometric pitch, or the distance this particular element would move forward in one revolution along a helix, or spiral, determined by its blade angle. The effective pitch is the actual distance a propeller advances through the air in one revolution. This cannot be determined by the pitch angle alone because it is affected by the forward velocity of the aeroplane and air density. The difference between geometric and effective pitch is called propeller slip. If a propeller has a pitch of 50 inches, in theory it should move forward 50 inches in one revolution. But if the aircraft actually moves forward only 35 inches in one revolution the effective pitch is 35 inches and the propeller efficiency is 70%.


Sample

Module 17 Propeller

Figure 1.4: Effective pitch, Geometric pitch and Slip (measured at Master Station)


Sample

Module 17 Propeller Angle of Attack Thrust produced by a propeller, in the same way as lift produced by a wing, is determined by the blade’s angle of attack. It is the acute angle between the chord line of a propeller blade and the relative wind. Angle of attack relates to the blade pitch angle, but it is not a fixed angle. It varies with the forward speed of the aeroplane and the RPM of the propeller. As an example, when there is no forward speed, angle of attack (α) and blade pitch angle are the same, 20°. When the aeroplane is moving forward at 60 knots, angle of attack becomes much less than the blade pitch angle (see figure 1.5).


Sample

Module 17 Propeller

Figure 1.5: Angle of Attack at different forward speeds


Sample

Module 17 Propeller Propeller Configuration There are four main propeller configurations:

• Pusher • Tractor • Contra-Rotating • Counter-Rotating

All the above types can be between two and five bladed propellers, but usually small two blade propellers are used on small piston engines and three, four or five bladed propellers are used for high powered piston or gas turbine engines.

Pusher A little confusing, as it is sometimes known as the ‘Propeller’. This type, as the name implies, pushes the airframe through the air and is usually fitted behind the mainplane.

Tractor This type pulls the airframe through the air and is usually fitted forward of the mainplane.


Sample

Module 17 Propeller

Figure 1.6: Pusher propellers on the Piaggio P.180 Avanti

Figure 1.7: The Cessna 337 Skymaster has a pusher AND a tractor

propeller


Sample

Module 17 Propeller

Contra-Rotating This configuration is where there are two propeller units on one shaft, driven by the same engine, but rotating in opposite directions. This gives the advantage of reducing the disc area, but maintaining the thrust to enable lower undercarriage configurations to be used or higher RPM’s from the engine due to reduced tip speed. When a propeller has more than six blades, it becomes inefficient, a contra-rotating propeller is also a method of overcoming this problem. The rear propeller is usually of a smaller diameter than the front propeller, so the blade tips will not be affected by air vortices from the front propeller tips.

Counter-Rotating With a large rotating mass such as a propeller, it will produce a significant turning moment or torque on the airframe. To overcome this problem on multi-engined aircraft, counter rotating propellers are often used. In this system you would have, for example, the port engine propeller rotating clockwise and the starboard engine propeller rotating anti-clockwise, thus balancing the torque effects. Propeller Solidity Solidity is the term used to describe the ability of the propeller to absorb power from the engine. For example a C130 propeller will require high solidity, whilst a Cessna 150 will be somewhat less. Solidity is defined as ‘The surface area of the propeller divided by the surface area of the propeller disc’

Solidity may be increased by:

• Increasing number of blades (limited by hub strength so contra-rotating is an option)

• Increasing the chord of the blades (C130 uses ‘paddle’ type blades)

• Increasing the length of the blades (Limited by tips going sonic and ground clearance).


Sample

Module 17 Propeller

Figure 1.8: The Contra-rotating propeller of the P51 Unlimited

Racer

Figure 1.9: Counter-rotating propellers

Figure 1.10: Solidity


Sample

Module 17 Propeller Propeller Clearances Ground Clearance The clearance that exists between the propeller tip and the ground when the aircraft is in the normal flying attitude is termed ground clearance. On an aircraft with a tail wheel configuration, it would have to be in the takeoff position to measure the ground clearance. Fuselage Clearance With a multi-engined aircraft, this is the clearance between the side of fuselage and the propeller tip.


Sample

Module 17 Propeller

Ref EASA CS 25.925 Figure 1.11: Propeller clearances


Sample

Module 17 Propeller Right and Left Handed Propellers A right handed propeller is one which rotates in a clockwise direction when viewed from aft - looking forward. A left handed propeller is one which rotates in an anti-clockwise direction when viewed from aft - looking forward. The Blade Element The aerodynamics of the propeller can most easily be understood by considering the motion of an element, or section of the propeller blade. Because the blade section of a propeller is an aerofoil section its aerodynamics can be studied in the same way, using the same terms. Rotational Velocity When the aircraft is stationary the motion of the element is purely rotational. At a given RPM the velocity of the blade element increases as it moves towards the blade tip. Shock wave effects as the tip speed approaches Mach 1 limit the length of blade. In addition there is the obvious limitation of tip to ground clearance. Forward Velocity When the propeller is stationary the forward velocity is entirely the due to the forward speed of the aircraft (TAS). However when the propeller is rotating and therefore drawing air through the blade disc then there is an additional induced airflow.


Sample

Module 17 Propeller

Figure 1.12: Aerofoil Terms

Figure 1.13: Airflow Components


Sample

Module 17 Propeller Blade Angle and Blade Pitch In order to develop the required aerodynamic force on the blade element it must be set at a small positive angle of attack to the resultant relative airflow. The Helix Angle plus the angle of attack equals the blade angle, which is more usually known as blade pitch. A blade element advances through space as though it was prescribing a helix. If it were 100% efficient then the distance it moves in 1-revolution is called the Geometric Pitch. However all blades have tip losses that cause Slip, resulting in a forward distance moved per revolution called Effective Pitch. Blade Twist Earlier it was stated that the rotational velocity increases with distance towards the blade tip. It is necessary therefore to reduce the blade angle towards the tip in order to maintain an efficient angle of attack (4o- 6o is the norm). This is the reason for the twist on a blade as shown in figure 1.15.


Sample

Module 17 Propeller

Figure 1.14: Blade Angle pitch relationships

Figure 1.15: Blade Twist


Sample

Module 17 Propeller Forces on a Blade Element The aerodynamic force produced by setting the blade element at a small positive angle of attack – i.e. the total reaction - may be resolved with respect to the direction of motion of the aircraft. The component thus obtained which is parallel to the flight path is the thrust force, and that which remains is the propeller torque force. Notice that the propeller torque force is the resistance to motion in the plane of rotation.


Sample

Module 17 Propeller

Figure 1.16: Blade Twist

Figure 1.17: Effect of speed on a fixed pitch propeller


Sample

Module 17 Propeller Variation of Propeller Efficiency with Speed

Figure 1.17 illustrates a fixed pitch propeller traveling at different speeds at a constant RPM. If the blade angle is fixed, the angle of attack will change with variations of forward speed. In particular, as speed increases, the angle of attack decreases and with it the thrust. The effect on propeller efficiency is as follows: a At some high forward speed the angle of attack of the blade

will be close to the zero lift incidence and thrust will reduce to zero.

b There will only be one speed at which the blade is operating

at its most efficient angle of attack (4o-6o) and where the propeller efficiency will be a maximum.

c At low speeds, the thrust will increase as the angle of attack

is increased . Provided that the blade is not stalled, the thrust is very large, but the speed is low and the propeller efficiency is low. Therefore at zero forward speed no useful work is being done and efficiency is zero.

These limitations to efficiency of a fixed pitch propeller led to the development of the two pitch propeller and later to the variable pitch propeller that enables the optimum angle of attack to be maintained throughout the flight range.

Windmilling Variable pitch propellers are prone to a condition known as windmilling. If the propeller suffers a loss of positive torque, the pitch will fine off in an attempt to maintain the governed RPM selected at the time. The relative airflow will impinge on the front surface of the blade section and cause drag and negative torque that will drive the engine rather than resist rotation. Figure 1.20 shows that in the windmilling condition there is a small negative angle of attack, causing the total reaction to act as shown. Resolving the Total Reaction into the two forces of thrust and torque results in the thrust acting in the reverse direction (however the magnitude is not very great) and the torque is acting with, and is assisting, rotation. It is this force that causes the propeller to speed up and cause a potentially damaging over speed of the powerplant. In addition the reverse thrust and extra form drag caused by the flat face of the propeller causes large drag forces to occur and hence cause considerable asymmetric forces on a twin or multiple engine aircraft. The aerodynamics are exactly the same as that which drives a ground based windmill, hence the name of this condition. Note that the windmill position is defined as having a small positive blade angle. However this will also mean it has a small negative angle of attack.


Sample

Module 17 Propeller

Figure 1.18: Efficiency Curves

Figure 1.20: Feathered Blade Section

Figure 1.19: Windmilling Propeller


Sample

Module 17 Propeller Feathering Following engine failure the windmilling propeller would cause drag and possibly cause engine damage due to over speeding leading to seizure or possibly engine fire. By turning the blades so that the aggregate effect of the blade section produces zero torque, the propeller is stopped and drag reduces to a minimum. The feathered position is therefore at approximately 90o to the plane of rotation. Reverse Thrust If the propeller is turned through the fine pitch stop to around minus 20o and power applied, reverse thrust is obtained. The blade section is working inefficiently, with the total reaction being produced in the reverse direction to normal. Mechanical devices are used to prevent application of power as the propeller passes through the windmill position, until safely in the braking range. This blade position is used on some enabled propellers to provide rapid braking after landing, and sometimes to reverse the aeroplane out from its parked position. A mechanical lock is often incorporated to prevent the pilot selecting reverse pitch whilst airborne. Forces Acting on the Propeller When a propeller rotates, many forces interact and cause tension, twisting, and bending stresses within the propeller. These forces are:

• Centrifugal Force • Bending Force • Torque Bending Force • Aerodynamic Twisting Moment (ATM) • Centrifugal Twisting Moment (CTM)

Centrifugal Force Centrifugal force puts the greatest stress on a propeller as it tries to pull the blades out of the hub. It is not uncommon for the centrifugal force to be several thousand times the weight of the blade. For example, a 10 kg propeller blade turning at 2,700 RPM may exert a force of 50 tons on the blade root.


Sample

Module 17 Propeller

Figure 1.21: Reverse Thrust

Figure 1.22: Propeller Centrifugal Force


Sample

Module 17 Propeller

Thrust Bending Force Thrust bending force attempts to bend the propeller blades forward at the tips, because the lift toward the tip of the blade flexes the thin blade sections forward. Thrust bending force opposes centrifugal force to some degree.

Torque Bending Force Torque bending forces try to bend the propeller blade back in the direction opposite the direction of rotation.


Sample

Module 17 Propeller

Figure 1.23: Thrust Bending Force

Figure 1.24: Propeller Torque Bending Force


Sample

Module 17 Propeller

Aerodynamic Twisting Moment (ATM) Aerodynamic twisting (or turning) moment tries to twist a blade to a higher angle. This force is produced because the axis of rotation of the blade is at the midpoint of the chord line, while the centre of the lift of the blade is forward of this axis. This force tries to increase the blade angle. Aerodynamic twisting moment is used in some designs to help feather the propeller. Figure 1.25 illustrates how ATM is produced. If the pitch change mechanism is behind the centre of pressure (the normal situation) the Total Reaction will tend to try to turn the blade towards a coarse pitch. It should be noted that in the normal forward thrust situation the CTM and ATM oppose each other, but be aware that CTM is a much greater force than ATM and hence CTM will always prevail and try to turn the propeller towards the windmill condition.

Centrifugal Twisting Moment (CTM) Centrifugal twisting (or turning) moment tries to decrease the blade angle, and opposes aerodynamic twisting moment. This tendency to decrease the blade angle is produced since all the parts of a rotating propeller try to move in the same plane of rotation as the blade centerline. This force is greater than the aerodynamic twisting moment at operational RPM and is used in some designs to decrease the blade angle. Figure 1.27 illustrates how the centrifugal force on the blade produces tensile stress at the blade root and a torque about the pitch change axis. The CTM tends to ‘fine’ the pitch and therefore the effort required by the pitch change mechanism to increase the blade angle towards ‘coarse pitch’ is increased.

CTM is greater at higher RPM, and with lower aspect ratio blades

Turning Moments in the Windmill Condition When the propeller is windmilling the total reaction works in the opposite direction. As a result ATM will also work in the opposite direction and add to the CTM force. Thus, when the power is lost to the propeller, the tendency of the blade to turn to low pitch (windmill position) is very large indeed.


Sample

Module 17 Propeller

Figure 1.25: Propeller Aerodynamic Twisting Moment

Figure 1.26: Propeller Centrifugal Twisting Moment

Figure 1.27: Centrifugal Twisting Moment


Sample

Module 17 Propeller Pitch Range The total pitch range extends from feathered to reverse Summary of typical blade angle settings indicating the large pitch range required to meet all requirements of a high performance engine Note: Pitch stops are fitted at each of the limits to prevent inadvertent operation outside of desired range.


Sample

Module 17 Propeller

Figure 1.28: Pitch Range for Variable Pitch propellers with Reverse

Thrust capability

Figure 1.29: Pitch positions Copyright 2014 © Total Training Support Ltd Module 17.1 Fundamentals

Sample

Module 17 Propeller Handling Effects - Single Engine Aircraft There are various handling effects on single engine aircraft in particular due to the rotating propeller.

• Asymmetric Effect (P-Factor) • Slipstream Effect • Torque Reaction • Gyroscopic Effect

Asymmetric Effect (P-Factor) In general, the axis of the propeller will be inclined upwards to the direction of flight due to the angle of attack of the aircraft. This causes the downward moving blade to have a greater effective angle of attack than the upward moving blade and therefore to develop a greater thrust The difference in thrust on the two sides of the propeller disc causes a yawing moment. For a right-handed propeller in a nose-up attitude, the yaw will be to the left.

Slipstream Effect In passing through the propeller, the air is accelerated and given velocity. The parts of the aircraft that are in the propeller slipstream will therefore have higher speed air passing over them than the parts outside the slipstream. The drag of the parts will therefore be higher and the effectiveness of any control surface in the slipstream will be greater. The rotation given to the slipstream will cause it to meet the fin at an angle and so cause a yawing moment.

This effect may be corrected by offsetting the fin or trimming the rudder. The amount of rotation given to the air will depend on the torque of the propeller and so the yawing moment will depend on the power setting.

Torque Reaction In rotating the propeller against the resistance of the air, reaction is produced which tries to rotate the aircraft in the opposite direction. For example, with a right hand propeller, the aircraft will tend to roll to the left. This is described by Newton’s Third Law of Motion: “For every action there is an equal and opposite reaction”. This tendency may be corrected by ‘wash in’ on the down going wing and ‘wash out’ on the up going wing. This method is not used on modern high performance aircraft.


Sample

Module 17 Propeller

Figure 1.30: P-Factor

Figure 1.32: Torque Reaction causing the aircraft to roll to the left

Figure 1.31: Slipstream Effect


Sample

Module 17 Propeller Gyroscopic Effect A rotating propeller has the properties of a gyro. If the plane of rotation is changed, a moment will be produced at right angles to the applied moment. For example, if an aircraft with a right handed propeller is yawed to the right it will experience a nose down pitching moment due to the gyroscopic effect of the propeller. Similarly, if the aircraft is pitched nose up, it will experience a yaw to the right. On most aircraft, the gyroscopic effects are small and easily controlled. The property of a gyroscope that is discussed above is known as precession. See figure 1.33. If a torque is applied as shown then precession will occur as shown. Direction of precession can be determined by taking the force causing the torque and rotating it through 90o in the direction of rotation. A ‘tail dragger’ single engine aircraft with a right-handed propeller will experience a yaw to the left as the tail lifts on its takeoff run.


Sample

Module 17 Propeller

Figure 1.33: Gyroscopic Effect


Sample

Module 17 Propeller

Figure 1.34: A tail-wheeled aeroplane experiences a yaw to left when the tail lifts off the ground

Thrust and Power Development

Power Development in Piston Engines The power output of a piston engine depends on the density of the combustible mixture of fuel and air introduced into its cylinders at that part of the operating cycle known as the induction stroke. On this stroke, the piston moves down the cylinder, an inlet valve opens, and the fuel/air mixture, or charge prepared by the carburetor, enters the cylinder as a result of a pressure difference acting across it during the stroke. If for example an engine is running in atmospheric conditions corresponding to the standard sea level pressure of 14.7 lbf/in2, and the cylinder pressure is reduced to, say 2lbf/in2, then the pressure difference is 12.7 lbf/in2, and it is this pressure difference that pushes the charge into the cylinder. An engine in which the charge is induced in this manner is said to be normally aspirated. Its outstanding characteristic is that the power it develops steadily falls off with decrease in atmospheric pressure. Supercharging The limitation on the high altitude performance of a normally aspirated engine can be overcome by artificially increasing the available pressure so as to maintain as far as possible a sea-level value in the induction system. The process of increasing pressure and charge density is known as supercharging or boosting, and the device employed is, in effect, a centrifugal compressor fitted between the carburetor and cylinders and driven from the engine crankshaft through step-up gearing. Power may be measured in inches of mercury or lbf/in2 and is known as manifold pressure.

An alternative higher power supercharging system uses a turbine driven centrifugal compressor powered by exhaust waste gases. This later form is often known as a turbo-charger or ground boosting turbo-charger and is capable of increasing boost pressure above atmospheric for take off purposes. This system is fitted at the inlet to the induction system and uses a fuel injection system at the induction valve inlet to mix the fuel and air. Power is normally measured in lbf/in2 and is often called boost pressure.

Power Development in Turboprop Engines A turboprop engine is a gas turbine engine configured to transmit the majority of the jet exhaust to power a free or power turbine assembly connected directly to a reduction gear that drives a propeller. The propeller always runs slower than the engine and must be large enough to absorb the power developed by the engine. To increase power in a gas turbine engine whether turboprop or pure jet one must increase fuel flow, thus increasing the energy available to drive the compressor and to turn the propeller/reduction gear assembly or to produce thrust. Fuel flow is increased by opening a throttle valve in a Fuel Flow Governor. These vary in complexity but the principle of more fuel for more power is always true. Power output in a turbo shaft engine is measured either by Shaft or Brake Horsepower. For a turboprop engine power is measured in terms of Torque. Torque is a function of the resistance to rotation. Therefore for a greater torque, greater power is required to turn the propeller. Resistance to motion can be varied by using a variable pitch

Intentionally Blank


Sample

Module 17 Propeller propeller. In a coarse pitch setting the propeller is gathering more air and thus is harder to turn. Torque meters can be in the form of a mechanical system utilizing oil pressure, or digital strain gauge systems. Total loss of torque will indicate engine failure and can be used to initiate an auto feather sequence. The fuel control lever in a turboprop engine is often known as the Power Lever. In a pure jet engine it is usually called the Throttle Lever, however both levers do exactly the same thing, they regulate the fuel supply to the combustion chambers. Whereas in a piston engine there are two levers to control power - Throttle lever and Propeller Condition Lever - it is more normal in a turboprop engine to have a combined power lever, that through a cam arrangement presets the variable pitch system to the power required.


Sample

Module 17 Propeller

Figure 1.35: Turboprop engine power development


Sample

Module 17 Propeller Turboprop Configurations Note all the below configurations all incorporate a reduction gear prior to connecting to the propeller shaft. This is because whilst the turboprop engine is required to rotate at speeds up to 100,000 RPM to maintain its efficiency, the propeller must rotate at just a fraction of that speed, in order to prevent its tips exceeding sonic speed.


Sample

Module 17 Propeller

Figure 1.36: Turboprop engines configurations


Sample

Module 17 Propeller Vibrational Forces and Resonance When a propeller is producing thrust, aerodynamic and mechanical forces are present which cause the blades of the propeller to vibrate (see figure 1.37). A person designing a propeller must take this into consideration. If this is not done, these vibrations may cause excessive flexing, hardening of the metal and could result in sections of the propeller breaking off during operation. Aerodynamic forces have a great vibration effect at the tip of the blade where the effects of transonic speeds cause buffeting and vibrations. Mechanical vibrations are caused by power pulses in a piston engine and are more destructive then aerodynamic vibrations. The most critical location when looking for the stresses is about 6 inches from the propeller tip. Most airframe-engine-propeller combinations have no problem in eliminating the effects of vibrational stresses. However some combinations are sensitive to certain RPM ranges and they have a critical range indicated on the tachometer by a red arc. The engine should not be operated in this range. If it is operated in the critical range over a period of time, there is a strong possibility that the propeller will suffer from structural failure due to the vibrational stresses.


Sample

Module 17 Propeller

Figure 1.37: Propeller Vibration


Sample

Module 17 Propeller Glossary Accumulator - A device to aid in unfeathering a propeller. Aerodynamic twisting moment - An operational force on a propeller which tends to increase the propeller blade angle. Angle of attack - The angle between the chord line of a propeller blade section and the relative wind. Anti-icing system - A system which prevents the formation of ice on propeller blades. Automatic propeller - A propeller which changes blade angles in response to operational forces and is not controlled from the cockpit. Trade name: Aeromatic®. Back - The curved side of a propeller airfoil section that can be seen while standing in front of the aeroplane. Blade - One arm of a propeller from the hub to the tip. Blade angle - The angle between the blade section chord line and the plane of rotation of the propeller. Blade index number - The maximum blade angle on a Hamilton-Standard counterweight propeller. Blade paddle.- A tool used to turn the blades in the hub. Blade root - The portion of a blade which is nearest the hub.

Blade station - A distance from the centre of the propeller hub measured in inches. Boots - Ice elimination components which are attached to the leading edge of propeller blades. Boss - The centre portion of a fixed-pitch propeller. Brush block - The component of a de-icing and/or reversing system which is mounted on the engine nose case and holds the brushes which transfer electrical power to the slip ring. Centrifugal force - The force on a propeller which tends to throw the blades out from the propeller centre. Centrifugal twisting moment - The force on a propeller which tends to decrease the propeller blade angle. Chord line - The imaginary line which extends from the leading edge to the trailing edge of a blade airfoil section. Comparison unit - The unit in a synchronization or synchrophasing system which compares the signals of the master engine and the slave engine and sends a signal to correct the slave engine RPM or blade phase angle. Cone - The component used in a splined-shaft installation which centers the propeller on the crankshaft. Constant-speed system - A system which uses a governor to adjust the propeller blade angle to maintain a selected RPM. Controllable-pitch propeller - A propeller whose pitch can be changed in flight by the pilot's control lever or switch.


Sample

Module 17 Propeller Critical range - The RPM range at which destructive harmonic vibrations exist. De-icing system - An ice elimination system which allows ice to form and then breaks it loose in cycles. Dome assembly - The pitch-changing mechanism of a Hydromatic® propeller. Effective pitch - The distance forward that an aircraft actually moves in one revolution of the propeller. Face - The flat or thrust side of a propeller blade. Feather - The rotation of the propeller blades to an angle of about 90 degrees which will eliminate the drag of a windmilling propeller. Fixed-pitch propeller - A propeller, used on light aircraft, whose blade angles cannot be changed. Flanged shaft - A crankshaft whose propeller mounting surface forms a flat plate 90 degrees to the shaft centerline. Frequency generator - The engine RPM signal generator for some synchronization systems. Geometric pitch - The theoretical distance that an aircraft will move forward in one revolution of the propeller. Governor - The propeller control device in a constant- speed system

Go no-go gauge - A gauge used to measure wear between the splines of a splined crankshaft. Ground-adjustable propeller - A propeller which can be adjusted on the ground to change the blade angles. Hub - The central portion of a propeller which is fitted to the engine crankshaft and carries the blades. Hydromatic® - A trade name for one type of Hamilton-Standard hydraulically operated propellers. Integral oil control assembly - A self-contained propeller control unit used on some transport aircraft. Leading edge - The forward edge of a propeller blade. Overhaul facility - An FAA approved facility for major overhauls and repairs. Pitch - The same as geometric pitch. Often used interchangeably with blade angle. Pitch distribution - The twist in a propeller blade along its length. Pitch lock - A mechanism used on some transports to prevent excessive overspeeding of the propeller if the governor fails. Plane of rotation - The plane in which the propeller rotates, 90 degrees to the crankshaft centerline. Propeller - A device for converting engine horsepower into usable thrust.


Sample

Module 17 Propeller Propeller disc - The disc-shaped area in which the propeller rotates. Propeller repair station - See overhaul facility. Propeller track - The arc described by a propeller blade as the propeller rotates. Pulse generator - The unit which generates an RPM and blade position signal in a synchrophasing system. Radial clearance - The distance from the edge of the propeller disc to an object near the edge of the disc, perpendicular to the crankshaft centerline. Reversing - Rotation of the propeller blades to a negative angle to produce a braking or reversing thrust. Safetying - The installation of a safety device such as safety wire or a cotter pin. Selector valve - Propeller control unit in a two-position propeller system. Shank - The thickened portion of the blade near the centre of the propeller. Shoe - See boot. Shoulder - The flanged area on the butt of a propeller blade which is used to retain the propeller blades in the hub. Slinger ring - The fluid distribution unit on the rear of a propeller hub using an anti-icing system.

Slip - The difference between geometric pitch and effective pitch. Snap ring - A component of a splined or tapered shaft installation which is used to aid in removal of the propeller. Spider - The central component on many controllable- pitch propellers which mounts on the crankshaft and has arms on which the blades are installed. Splined shaft - A cylindrical-shaped crankshaft extension which has splines on its surface to prevent propeller rotation on the shaft. Static RPM - The maximum RPM that can be obtained at full throttle on the ground in a no-wind condition. Synchronization system A system which keeps all engines at the same RPM. Synchrophasing system - A refined synchronization system which allows the pilot to adjust the blade relative position as they rotate. Tachometer-generator - The RPM-sensing unit of some synchronization systems. Tapered shaft - A crankshaft design whose propeller- mounting surface tapers to a smaller diameter and acts like a cone seating surface. Thrust bending force - An operational force which tends to bend the propeller blades forward. Tip - The portion of the blade farthest from the hub.


Sample

Module 17 Propeller Torque bending force - An operational force which tends to bend the propeller blades in the direction opposite to the direction of rotation. Two-position propeller - A propeller which can be changed between two blade angles in flight.


Sample

sample - total training supporttotaltrainingsupport.com/samples/17.1 fundamentals (landscape... ·...

Documents