s universal billiard n accessory drawer o · 2018-05-24 · 1 universal billiard accessory drawer...
TRANSCRIPT
1
U N I V E R S A L B I L L I A R D A C C E S S O R Y D R A W E R
P0900-00
2014 Escalade Sports
MODEL NO.
P0900
AS
SE
MB
LY
IN
ST
RU
CT
ION
S
Escalade® Sports products may be manufactured and/or licensed under the following patents.6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
2
Contact Escalade® Sports customer service department at:
Phone: 1-800-467-1245 Toll – Free !
Fax: 1-866-873-3533 Toll – Free !
E-mail: [email protected]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering
parts.
3. To make assembly easier, use the Hardware Identifier on page 3 to identify and sort all fasteners. Check all cartons for kits. All
hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and parts
may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Tools required for assembly: Tape Measure, Carpenter’s Square, Sharpie Marker, one 5/16” Wrench or 8 mm Wrench, 7/64” Drill Bit and
Cordless Drill. Note: Ratchet and Socket can be substituted for open end wrenches. A portable light or lamp is also helpful to see under table.
6. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for
replacement parts.
Please Do Not Return This Product To The Store!
Please visit our Website at:www.escaladesports.comON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE®
SPORTS PRODUCT INFORMATION
P R E - A S S E M B L Y T I P S
2014 Escalade Sports
AS
SE
MB
LY
T
IPS
3
Drawer, Billiard AccessoryHangerConnectorMounting RailMounting FrameDrawer Decal Sheet#10 X 1" Long, Hex Washer Head Sheet Metal Screw#8-32 Serrated Flange Hex NutInstruction Manual
P0900-P1P0900-P2P0900-P3P0900-P4P0900-P5P0900-P6P0900-H1P0900-H2P0900-M1
P1P2P3P4P5P6H1H2M1
Key# Description
Replacement Parts List for Model Number P0900
Part # Qty.
144211 4201
Part H2Qty. 20
HARDWARE IDENTIFIER:
P5
P4
P6
H1H2
P3
P2
P1
Part H1Qty. 4
4
PLEASE LOOK AT YOUR TABLE AND DETERMINE THE POSITIONING OF YOUR BEAMS.
INSTALLATION WILL DEPEND ON THE TYPE OF BEAM SUPPORTS YOU HAVE ON YOUR
POOL TABLE. IF THE BEAMS RUN THE WIDTH OF THE TABLE SEE PICTURE A. IF THE
BEAMS RUN THE LENGTH OF YOUR TABLE SEE PICTURE B.
B
IF THE BEAMS RUN THE LENGTH OF
THE TABLE LIKE IN PICTURE B SKIP TO
PAGE 16 AND FOLLOW THOSE
DIRECTIONS TO INSTALL YOUR
ACCESSORY DRAWER.
A
IF BEAMS RUN THE WIDTH OF THE TABLE LIKE
IN PICTURE A GO TO THE NEXT PAGE AND
FOLLOW THOSE DIRECTIONS.
5
OVERVIEW OF INSTALLATION PROCEDURE:
BOTTOM EDGE
FRONT OF DRAWER
4”
20”
location of the first row of mounting holes
location of the Secondrow of mounting holes
BEAMSUPPORT
DETERMINE IF YOU WANT YOUR DRAWER TO BE FLUSH TO
THE SIDE APRON OR RECESSED.
SIDE VIEWOF TABLE
BOTTOM VIEWOF TABLE
Beam Supporton your table
Beam Supporton your table
THE FRONT OF DRAWER WILL GO ON THIS SIDE
OF THE TABLE
Please look at the pictures below and familiarize yourself with your pool table
and which side of the table you want to attach your accessory drawer to. When
fully assembled the Drawer should be flush to the bottom edge of the Side
Apron of your table (unless you want the Drawer recessed), this is why its
important to measure accurately before pre-drilling your holes. Continue to the
next page to start assembly, you will need a cordless drill, a 7/64” drill bit a
tape measure and a fine tip marker such as a Sharpie.
NOTE:
OF SIDE APRON
6
BOTTOM VIEWOF TABLE
OF SIDE APRON
BEAMSUPPORTS
16”
1. Determine which side of your pool table you want to attach your Accessory Drawer
and how far in (recessed) from the bottom edge of Side Apron.
1Figure
2. Measure 4” from the outside of the front face of the Drawer to the center of the
Beams on your table. Mark the location of where you will drill the pilot holes,
making sure hole marks are parallel to each other. See Figure 1.
3. Measure 20” from the outside of the Front of the Drawer (or 16” from the first set
of holes) to the center of the Beams. Mark the location of where you will drill the
pilot holes, making sure hole marks are parallel to each other. See Figure 1.
4. Double check the makings for the pilot holes before drilling. Hole markings must
be centered and square to other hole markings for proper drawer alignment.
Using a 7/64” bit, drill pilot holes about 1” deep into the Beam supports, keep
Drill straight when drilling so pilot hole is as straight as possible.
BOTTOM EDGE
FRONT OF DRAWER
4”
20”
location of the first row of mounting holes
location of the Secondrow of mounting holes
BEAMSUPPORT
SIDE VIEWOF TABLE
OF SIDE APRON
FRONT OF DRAWER
DETERMINE IF YOU WANT YOUR DRAWER TO BE FLUSH TO
THE SIDE APRON OR RECESSED.
NOTE:
4”
20”
BOTTOM EDGE
7
(MOUNTING RAIL)P4
2Figure
THREADED STUDS
THREADED STUDS
(MOUNTING SLOTS)
5. Become familiar with Mounting Rail P4. Different mounting
slots will be used depending on the distance between your
Beam supports. You will attach screws H1 through the
mounting slots and into the pre-drilled holes you made in the
previous step. The threaded studs will be facing toward the
back when attached to the pool table Beams in the next step.
See Figure 2.
(MOUNTING SLOTS)
Note: H1 Screws will attachfrom the bottom in the
next step.
6. You will need two P4 Rails and four H1 Screws for the next
step.
8
Threaded studs on P4 Rail must be facing toward the
back as shown.
SIDE VIEWOF TABLE
3Figure
BEAMSUPPORTS
THE FRONT OF DRAWER WILL
GO ON THIS SIDE
BOTTOM VIEWOF TABLE
THE FRONT OF DRAWER WILL
GO ON THIS SIDE
DETAIL A
Threaded studs on P4 Rail must be facing toward the back.
Threaded studs on P4 Rail must be facing toward the
back as shown.
Threaded studs on P4 Rail must be facing toward the back.
P4
7. Attach Mounting Rails P4, to the support Beams with four H1 screws. Attach
screws H1 through the mounting slots and into the pre-drilled holes you made,
check to make sure Mounting Rails square, straight and centered on beams
before tightening, DO NOT over-tighten screws. The threaded studs should
be facing toward the back. See Figure 3, Detail A & Side View.
BEAMSUPPORTS
CAUTION:DO NOT OVER TIGHTEN SCREWS! BECAUSE YOU COULD STRIP SCREWS IN THE WOOD BEAMS DOING IRREPARABLE DAMAGE TO THE TABLE.
H1H1
9
TOP VIEW
NOTE: MAKE SURE THIS EDGE IS FACING UP
4Figure
PARTS NEEDED:
1 - (P5) Mounting Frame
8. Fold Mounting Frame P5 so that the noted threaded studs face out as
shown in Figure 4 & the Top View.
P5
Threaded studs
Threaded studs
Threaded studs
Threaded studs
Threaded studs
Threaded studs
Threaded studs
Threaded studs
P5
10
NOTE: P3 Connector can extend on slider along the slot on P2.
5Figure
P2
P3
H2
DETAIL B
P3
P2
P3
P2
9. Attach P2 hanger to P3 Connector with H2 Hex nut as shown in Figure 5. Leave nut
H2 loose enough for P3 to slide freely on P2. See Detail B. Repeat step for the
remaining P2 & P3 parts.
PARTS NEEDED:
4 - (P2) Hanger
4 - (P3) Connector
4 - (H2) Hex Nut
Stud
Threaded
11
6Figure
Threaded Studs on P4 Rail that you assembled in Step 7 will go in these holes in the next step.
10. Attach Hanger assemblies to the threaded studs on Mounting Frame P5 with
Hex Nuts H2 as shown in Figure 6.
PARTS NEEDED:
1 - (P5) Mounting Frame
4 - Hanger assemblies
8 - (H2) Hex Nuts
Hanger Assembly
H2
H2
Hanger Assembly
H2
Hanger Assembly
Hanger Assembly
H2P5
12
7Figure
Mounting Frame Assembly from previous page.
11. Attach Mounting Frame Assembly from Step 10 to the threaded studs on P4
Rails that were installed in Step 7. Use Hex Nuts H2 to secure assembly as
shown in Figure 7 and Detail C.
PARTS NEEDED:
1 - Mounting Frame Assembly
4 - (H2) Hex Nuts
DETAIL C
P4 Rails
P4 Rails
H2H2
THE FRONT OF DRAWER WILL GO ON THIS SIDE
OF THE TABLE
THE FRONT OF DRAWER WILL GO ON THIS SIDE
OF THE TABLE
13
8Figure
PARTS NEEDED:
1 - (P1) Drawer Assembly
2 - (H2) Hex Nuts
11. Attach Drawer Assembly by the threaded studs to the side hanger
assemblies with two H2 Hex Nuts. See Figure 8 & Detail D.
H2
Hanger Assembly
P1
H2
Hanger Assembly
P1
DETAIL D
THE FRONT OF DRAWER WILL GO ON THIS SIDE
OF THE TABLE
14
9Figure
PARTS NEEDED:
1 - (P1) Drawer Assembly
2 - (H2) Hex Nuts
12. Attach Drawer Assembly by the threaded studs to both end hanger
assemblies with two H2 Hex Nuts. See Figure 9.
THE FRONT OF DRAWER WILL GO ON THIS SIDE
OF THE TABLEHanger
Assembly
H2
NOTE: Hanger Assembly can extend
DETAIL E
Congratulations your assembly is complete!
13. Adjust height of your drawer to the desired height with the four Hanger
assemblies, making sure that drawer is level and that there is enough clearance
to open and close drawer. Once drawer is at the desired height tighten the
height adjustment nuts on the Slider Assemblies to hold drawer at that height.
Do a final check of all fasteners to ensure all are tight. See Detail E.
Height Adjustment
nut
15
PLEASE LOOK AT YOUR TABLE AND DETERMINE THE POSITIONING OF YOUR BEAMS.
INSTALLATION WILL DEPEND ON THE TYPE OF BEAM SUPPORTS YOU HAVE ON YOUR
POOL TABLE. IF THE BEAMS RUN THE WIDTH OF THE TABLE SEE PICTURE A. IF THE
BEAMS RUN THE LENGTH OF YOUR TABLE SEE PICTURE B.
B
IF THE BEAMS RUN THE LENGTH OF THE TABLE
LIKE IN PICTURE B CONTINUE TO THE NEXT
PAGE AND FOLLOW THOSE DIRECTIONS TO
INSTALL YOUR ACCESSORY DRAWER.
A
IF BEAMS RUN THE WIDTH OF THE TABLE LIKE
IN PICTURE A GO BACK TO PAGE 5 AND
FOLLOW THOSE DIRECTIONS.
16
TOP VIEW
NOTE: MAKE SURE THIS EDGE IS FACING UP
1Figure
PARTS NEEDED:
1 - (P5) Mounting Frame
1. Fold Mounting Frame P5 with the noted threaded studs facing out as
shown in Figure 1 & the Top View.
P5
Threaded studs
Threaded studs
Threaded studs
Threaded studs
Threaded studs
Threaded studs
Threaded studs
Threaded studs
17
NOTE: P3 Connector can extend on slider along the slot on P2.
2Figure
P2
P3
H2
DETAIL A
P3
P2
P3
P2
2. Attach P2 hanger to P3 Connector with H2 Hex nut as shown in Figure 2. Leave nut
H2 loose enough for P3 to slide freely on P2. See Detail A. Repeat step for the
remaining P2 & P3 parts.
PARTS NEEDED:
4 - (P2) Hanger
4 - (P3) Connector
4 - (H2) Hex Nut
Stud
Threaded
18
3Figure
3. Attach Hanger assemblies from Step 2 to the threaded studs on Mounting
Frame P5 with Hex Nuts H2 as shown in Figure 3.
PARTS NEEDED:
1 - (P5) Mounting Frame
4 - Hanger assemblies
8 - (H2) Hex Nuts
Hanger Assembly
H2
H2
H2
Hanger Assembly
Hanger Assembly
H2
P5
NOTE: MAKE SURE THIS EDGE IS FACING UP
Hanger Assembly
19
Mounting Screws will go in these holes when mounting the frame to the Beams on the table.
NOTE: SIDE WITH SLOTTED HOLES
FACES UP
Threaded studs.
Threaded studs.
H2
P4
P4
NOTE: SIDE WITH SLOTTED HOLES
FACES UP
4Figure
H2
PARTS NEEDED:
1 - Mounting Frame Assembly
2 - (P4) Mounting Rail
4 - (H2) Hex Nuts
4. Attach P4 Mounting Rails to Mounting Frame assembly from Step 3. Insert
Threaded Studs in the P4 Rails through the Mounting assembly and secure
with Hex Nuts H2 as shown in Figure 4.
20
BOTTOM VIEWOF TABLE
SIDE APRON
BEAMSUPPORTS
5. Determine which side of your pool table you want to attach your
Accessory Drawer.
5Figure
6. Determine where the middle of the table is and mark a centerline on the
inside of the first Beam Support. Measure 17.5” to either side from
the centerline and 3/8” in from inner face of Support Beam and mark
first hole location. Measure 35” from the first hole location and mark
the second hole location as shown in Figure 5.
7. Mark the third hole location to the center of the Second Support Beam
exactly straight across from the first hole Mark. Repeat for fourth hole
location but with Second hole mark. See Figure 5.
8. Using your Mounting Frame double check that the makings for the pilot
holes line up before drilling. Hole markings must be centered and
square to other hole markings for proper drawer alignment. Using a
7/64” bit, drill pilot holes about 1” deep into the Beam supports, keep
Drill straight when drilling so pilot hole is as straight as possible.
Mountingframe
assembly
Match these holes up with the hole mark on the Support Beams
before drilling any holes.
This face should be flush against the inner part of the first Support Beam.
35” Center line
Mark the Center line on the inside of the first Beam
Mark second hole location
Mark first hole location
3/8”
first hole location mark should line up with this hole
Second hole location mark should line up with this hole
Mark third hole location
Mark fourth hole location
Third hole location should line up with any
of these slots
Fourth hole location should line up with any
of these slots
Second BeamCenter line
21
6Figure
9. Attach Mounting Frame Assembly from Step 4 to the Support Beams. Use the pre-
drilled holes and H1 Screws to secure assembly as shown in Figure 6 and Detail B.
PARTS NEEDED:
1 - Mounting Frame Assembly
4 - (H1) Screws
DETAIL B
THE FRONT OF DRAWER WILL GO ON THIS SIDE
OF THE TABLE
FIRST BEAMSUPPORT
H1 H1
SECOND BEAMSUPPORT
CAUTION: DO NOT OVER TIGHTEN SCREWS! BECAUSE YOU COULD STRIP SCREWS IN THE WOOD BEAMS DOING IRREPARABLE DAMAGE TO THE TABLE.
SIDE VIEWOF TABLE
22
7Figure
PARTS NEEDED:
1 - (P1) Drawer Assembly
2 - (H2) Hex Nuts
10. Attach Drawer Assembly by the threaded studs to the side hanger
assemblies with two H2 Hex Nuts. See Figure 7 & Detail C.
H2
Hanger Assembly
P1
H2
Hanger Assembly
P1
DETAIL C
THE FRONT OF DRAWER WILL GO ON THIS SIDE
OF THE TABLE
23
8Figure
PARTS NEEDED:
1 - (P1) Drawer Assembly
2 - (H2) Hex Nuts
11. Attach Drawer Assembly by the threaded studs to both end hanger
assemblies with two H2 Hex Nuts. See Figure 8.
THE FRONT OF DRAWER WILL GO ON THIS SIDE
OF THE TABLEHanger
Assembly
H2
NOTE: Hanger Assembly can extend
DETAIL D
Congratulations your assembly is complete!
Height Adjustment
nut
12. Adjust height of your drawer to the desired height with the four Hanger
assemblies, making sure that drawer is level and that there is enough clearance
to open and close drawer. Once drawer is at the desired height tighten the
height adjustment nuts on the Slider Assemblies to hold drawer at that height.
Do a final check of all fasteners to ensure all are tight. See Detail D.
24
90 DAY LIMITED WARRANTY
®This consumer warranty extends to the original consumer purchase of any ESCALADE SPORTS Product
(hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of ninety (90) days from the original purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from defects in material and
workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED BY ACCIDENT,
UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT
OF DEFECTS IN MATERIAL AND WORKMANSHIP.
WARRANTY PERFORMANCE: During the above ninety (90) day warranty period, ESCALADE SPORTS shall repair or replace with a comparable model, and Product,
or component thereof, which may prove defective under normal use and proper care, and which our examination shall disclose to our satisfaction to be thus defective,
please contact our Warranty Dept.
1-866-873-3528 / Warranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty Products. ESCALADE® SPORTS strongly recommends that the
Product is insured for value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE ABOVE NINETY (90) DAY WARRANTY PERIOD.
ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR
DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above limitations or exclusions may not apply to
you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.