S C A N B O O K

Training

Training

INSTALLING SCAN BOOK

Installation: I Scan Book • Insert the installation CD into your Cd-Rom drive.• Click Start then Run. • Type D: setup and press <ENTER>• Follow the step by step installation procedure.

It is recommended that SCANBOOK is installed into your local directory (C local)

C:\Scan Book: this will create a program group called Scan book in your start menu.

End of Installation I

Installation:II ScanBook Directory Creation

In the Scan Book application 2 folders will need to be created, the first folder will contain all scanned and processed data. The second folder will contain job/form definitions.

• Select Start • Select Programs• Select Scan Book • Select File

• Select New: folder create a folder with the name:Scan Data, press enter. This folder will contain all scanned and processed data.

• Select New: folder: create a folder with the folder name: Scan JobsThis folder will contain all form/job definitions.

Installation II continued…

After you have completed 2 of the 3 installations close your scan book folder, by selecting the X in the upper right hand corner.

The last installation will be to configure your scanner. For this installation you will use Scan Book software.

Installation III Starting Scan Book

– Select Start

– Select Programs

– Select: Scan book for windows

Scan Book opens with the Process Log window by default.The Process log window shows the results of a scanning job as they are sent to Scan Book.

CONFIGURING YOUR SCANNER

CONFIGURING YOUR SCANNERVerifying your scanner communicates with the Scan Book software.

•Select the “Tools” pull-down menu

Select Scanner Properties. Your scanner settings for this tab should read as the following:

If you are unsure of the port,

start with COM 1.

SELECT The SCANNER TAB: Make sure your ES 2260 scanner is powered on at this point.

• Select the “Detect” button.

If the scanner did not detect, return to the COM port tab and change to another Port ….COM 2

If the scanner is communicating, the model number and channels will automatically change to your scanner’s settings

Before you begin scanning you need to instruct Scan Book to interact with your scanner to retrieve data. You do this by setting up a Job that defines the following settings:

A list of Forms to be scanned.

The name of the file to store results of the scanning session.

(If you do not specify a file name, the data will not be not saved)

Your OMR configuration.

Creating a Job Definition

Creating a Job Definition:

• Select File

• Select New:

Creating a Job Definition continued

• Select Job Definition

Process Tab

Output File:It is recommended to save the outputData file (along with saving the FORM Definitions) to the local hard drive. OrYou may save information to a floppy or network drive location.

C:\ScanBook\Scan data\Subject\Teacher. CSV

You will need to create a folder in your Scan Book application using

the following directory

•Select here

Enter the name of the fileThe extension must be “.csv”)

Select Save

Forms Tab• Select the Forms Tab• Double Click Form 19632.SH

You have now selected the available form.•Select okay

IF YOU RECEIVE AN ERROR MESSAGE STATING FORM NOT AVAILABLE

• From the Forms Tab• Form folder• Select the ellipses • You will need to verify if your forms definition folder has been

created.

• Verify that you have a Scan Jobs folder created.• Select okay

Initial ValuesOptional Settings:

Initial Values Tab:The setting of the Job Properties contains the settings returned from, or printed by your scanner.The 2260 model has the ability to print messages on Forms as they are scanned. (Please remember this is optional)If you enter Batch: ^^^Booklets: | | |Number: ~ ~ ~ ~Will print on your scanned formsBatch: 001Booklet: 001 Number: 00001(Please remember this is optional)

The Starting Serial, Booklet or batch number.Any messages you want printed on the form as they are scanned (Requires the printer option on your scanners)Special Characters used to represent errors and other contingencies

Global Values Global Values Tab:This option controls the specific characters that are entered in the output record when particular situations arise. It is recommended that these settings should not be changed. The settings shown here should look identical to the settings on your 2260 scanner.

Creating a Job Definition continued…

•Select okay from the Job Properties Box.

Job Properties.

•Select the Process-Pull down Menu

Select a setting to use. This will tell the scanner to stop when scanning a

form, if the situation occurs.

Make sure you have a “ ,” placed in this field.

STARTING THE SCAN JOB

Select the Process-Pull down Menu

Select Scan Job

The Form Definition will download to the scanner.

Pre-Scanning Checklist It is recommended to organize and scan your forms by subject and teacher.

In case you need to re-visit the hard copy forms again you will be able to locate a particular form .

Remove any stray marks from the form.

Observe the timing marks on the left-hand side of your form.

Verify the demographic data in the form: Student Id and Tested: (If the demographic information was hand-bubbled)

If your form is torn or contains extra marks the scanner will NOT read the form.

Remove any paperclips.

Do not Staple Forms together.

Pre-Scanning Checklist continued..

Pre-Scanning Checklist continued..

Remove any blank forms as they do not need to be scanned.

Students should use PENCIL only to select their answers.

NO PENS or MARKERS are ALLOWED.

Before scanning•select the process log•Select the window pull-down menu

Process LogOnce the forms you wish to scan are defined and scanning jobs created within Scan Book, you are now ready to begin scanning form data.During processing, Scan Book receives the data form the ES 2260 scanner and displays it in the Process Log window as it writes the data to the file. Each line in the Process Log window represents a single form.

OPERATING THE ES 2260

Operating the ES2260USING THE CONTROL PANEL

A. LCD Display E. Key 1B. Power Lamp F. Key 2C. Receive Lamp G. Select KeyD. Transmit Lamp H. End Key

Press Key 1 to perform the function that is displayed on the LCD.The END Key is used to end a process mode or scan job.The SEL (select) Key is used to select an option or process and to enter a mode of operation.

Operating Messages from your E2260

End of Batch: The end key (located on the control panel) was pressed.

Feed Form: The scanner received a valid read command from

your computer and is ready to read a form.

Feeding Form: The scanner is feeding a form under the redhead.

Rejecting: The scanner detects form and/marking error(s) on the current form and directs the form to the output hopper.

Feeding Forms Place the scanner in a slanted position so forms will stack properly

in the output hopper (I). Orient the form so that the timing track is facing you. Place the Form into the input hopper (C) with the edge close to the

timing track at the bottom of the input hopper.

Feeding Forms Continued…

Make sure that the form rest on the bottom of the input hopper. Gently press the input hopper tray (A) to lower it into position for

loading forms.

Feeding Forms Continued…

Adjust the input hopper form guide (D) so that it rests near the top

edge of the forms.

Feeding Forms Continued…

Place the paperweight on top of the forms.

To attach the paperweight: Lower the input hopper tray and load the forms. Insert the paperweight insertion slot (A) along the bottom of the input hopper until the retaining tab (B) is secured on the edge (C) of the input hopper. The paperweight should rest on the stack of forms inside the input hopper.Raise the input hopper tray.

Feeding Forms Continued…

Do not insert the leading edge (D) of the form underneath the input rollers until the LCD (E) displays “feed the form”.

You can use the input hopper extension if need be.

Verify that the LCD displays feed the form.

Feed the form until the input rollers begin pulling the form. (Do not push the form into the scanners)

If the form lodges in the paper path, remove the form from the paper path press KEY 2 (G) to continue scanning, and scan the dislodged form again.

When you are finished scanning forms, Press the End key (H) on the scanner.

Feeding Forms Continued…

If the scanner is correctly connected to the host computer, the following actions occur while feeding forms:

The Receiver Lamp blinks as the scanner receives a command from the computer.

The LCD displays Feed Form when the scanner receives a command to read a form and continues to display until you feed a form.

The LCD displays Transmitting and the transmit lamp blinks when the scanner transmits data.

Operating the ES 2260

As you feed forms into the scanner, the ES 2260 either accepts or rejects the forms.

Accepted Forms:The ES2260 accepts a form if the scanner detects no marking errors

(bad erasures, multiple marks, missing marks, etc) or form errors (wrong number of timing lines, wrong side of forms, etc)

Accepted forms travel through the ES 2260 and eject into the output hopper (I). The data read from the form transmits to your computer,

and the scanner then is ready to receive another form.

Operating the ES 2260

Rejected FormsThe ES 2260 rejects a form if the scanner detects one (or more) of the

following form and/or marking errors.

Double sheets feeding into the scanner.

Missing marks where at least one mark must exist.

Rejected Forms Continued…

Multiple marks where only one mark is allowed.

Wrong number of timing lines.

Wrong identification marks or wrong form.

Wrong side of the correct.

Rejected forms will travel through the scanner and eject into the output hopper, according to the option specified in your form definition:

If the stop-on-error option of the READ command is enabled, the scanner will stop and require operator intervention.

If the stop-on-error option is not enabled, the scanner will transmit a signal to the application that an error occurred, and the application program determines what to do with the form.

Avoiding Common ProblemsMinor preparation can help you to avoid the most common problems associated with collecting data from scannable forms. Here are a few trouble shooting ideas.

Form jams: Straighten pinched or dog-eared forms. Remove all staples, tap or paper clips. Flatten creases in folded forms.

Rejected forms: Orient the forms properly while feeding Ensure that the forms are undamaged and intact (no tears). Check critical form sections for correct information. Make sure you fed the form properly

(For example, timing track at the bottom of the input hopper.)

Scanner Service

If you need to schedule service: schedule service before the district exam administration. Each school is responsible to schedule service, outside of the December yearly scheduled service.

Call Scantron Service Group @1-800-824- 2023 provide the Model No. and Serial No. and any additional information required.

Q U E S T I ON S ?