rt 42px20 chassis rf 043b service manual
TRANSCRIPT
PLASMA TVSERVICE MANUAL
CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : RF-043B
MODEL : RT-42PX20
website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html
- 2 -
CONTENTS
SAFETY PRECAUTIONS ...................................................................................3
DESCRIPTION OF CONTROLS ........................................................................ 4
SPECIFICATIONS ............................................................................................ 13
ADJUSTMENT INSTRUCTIONS ......................................................................15
TROUBLE SHOOTING GUIDE..........................................................................18
BLOCK DIAGRAM.............................................................................................29
EXPLODED VIEW..............................................................................................32
EXPLODED VIEW PARTS LIST ........................................................................33
REPLACEMENT PARTS LIST...........................................................................34
SCHEMATIC DIAGRAM ........................................................................................
PRINTED CIRCUIT BOARD ..................................................................................
- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.
It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.
When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.
Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
To Instrument'sexposed METALLIC PARTS
Good Earth Groundsuch as WATER PIPE,CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF
- 4 -
DESCRIPTION OF CONTROLS
- When using the remote control aim it at the remote control sensor of the set.- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.
POWERMUTE
TV/AV MULTIMEDIA
LIST ARC MENU
PR
PR
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM PIP/DW SLEEP
REVEAL TEXT/PIP PR+
WIN. SIZE MIXPIP PR-
POSITION TIMESWAP
HOLD INDEXPIP INPUT
?
i
I/II
MULTIMEDIASelects the Component, RGB or DVI
modes.
PIP/DWSwitches the sub picture on or off.
Selects PIP or DW modes.PIP PR + /-
Selects a programme for the sub picture.SWAP
Alternates between main and sub pic-ture.
PIP INPUTSelects the input mode for the sub pic-
ture.WIN.SIZE
Adjusts the sub picture size.POSITION
Moves the sub picture to DD / EE or FF / GGdirection.
POWERswitches the set on from standby oroff to standby.
ARC Changes the picture format.
MENUDisplays on screen menus one byone.Exits the current menu.Memorizes menu changes.
SWAPReturns to the previously viewedprogramme.Note : This function works onlywhen Favorite programme is set to Off.Otherwise each press of this buttonwill select a stored favorite pro-gramme.
SSMTo select the sound appropriate toyour viewing programme character.
NUMBER buttons
SLEEPSets the sleep timer.
I/IISelects the language during dual lan-guage broadcast.Selects the sound output.
TEXTThese buttons are used for teletext.For further details, see the ÔTeletextÕsection.Note : In teletext mode, the PIP PR+/-, SWAP and PIP INPUT buttons areused for teletext function.
LISTDisplays the program table.
TV/AVSelects the TV, AV, Component, RGB
or DVI modes.
MUTESwitches the sound on or off.
DD / EE (Programme Up/Down)selects a programme or a menu item.
switches the set on from standby.FF / GG (Volume Up/Down)
adjusts the volume.adjusts menu settings.
OKaccepts your selection or displays the
current mode.
PSMAdjusts the factory preset picture
according to the room.
SPLIT ZOOMEnlarge the screen with regular
ration.
- 5 -
<Front Panel Controls>
ON/OFF
TV/AV MENU VOL PR
TV/AV MENU VOL PR
- Shown is a simplified representation of the set.- Here shown may be somewhat different from your set.
Main Power Button
Remote Control Sensor
TV/AV ButtonSelects the TV, AV, Component,RGB or DVI modes. If OSD is dis-played, selects menu item.
MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.
DD / EE (Programme Up/Down)selects a programme or a menu item.
switches the set on from standby.FF / GG (Volume Up/Down)
adjusts the volume.adjusts menu settings.
Power Standby IndicatorIlluminates red in standbymode, Illuminates greenwhen the set is turned on
or
- 6 -
<Back Panel>
RS-232C INPUT(CONTROL/SERVICE)
REMOTECONTROL
DVI INPUT
S-VIDEO
AUDIO VIDEO
MONITOROUTPUT
A/VINPUT1
AUDIO
R L
AntennaAC INPUT
VIDEO
INPUT 2COMPONENT
INPUT 1COMPONENT
AUDIO INPUT RGB INPUT
R L/MOND
S-V
IDE
OV
IDE
OA
UD
IO
AV2
RL/
MO
NO
1. CONTROL LOCK / REMOTE CONTROL
2. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.
3. DVI INPUT / AUDIO INPUT / RGB INPUTConnect the monitor output socket of the PERSONAL COM-PUTER to this socket.
4. COMPONENT INPUTConnect DVD video outputs to Y, PB, PR of COMPONENTINPUT and audio outputs to Audio sockets of AUDIO INPUT.
5. AUDIO/VIDEO IN SOCKETS (AV1)Connect the audio/video out sockets of external equipment tothese sockets.S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEOsocket. Connect the audio out sockets of the VCR to the audio sock-ets as in AV1.
6. ANTENNA INPUT
7. POWER CORD SOCKETThis Monitor operates on an AC power. The voltage is indi-cated on the Specifications page. Never attempt to operatethe Monitor on DC power.
8. AUDIO/VIDEO IN SOCKETS (AV2)S-VIDEO/AUDIO IN SOCKETS
3 4 5 76
8
1 2
- 7 -
- Be careful for the bronze wire not to be bended in connecting to antenna input port.
Antenna Connection
INPUT
S-VIDEO
AUDIO VIDEO
MONITOROUTPUT
A/VINPUT1
AUDIO
R LAntenna
AC INPUT
VIDEO
INPUT 2COMPONENT
INPUT 1COMPONENT
AUDIO INPUT RGB INPUT
R L/MOND
Watching VCR- When connecting the Monitor to external equipment, match the colours of connecting ports (Video - yellow, Audio (L) - white,
Audio (R) -red).- Connect the VIDEO INPUT socket (yellow) to the VIDEO INPUT on the set.- If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the set. - If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR
to the Video input. - Use the orbiter function to Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still pic-
ture from a VCR. (Refer to p. 25)If a 4:3 picture format is used; the fixed image may remain visible on the screen.
- To avoid picture noise (interference), leave an adequate distance between the VCR and set.
Watching TV programmes- Turn the set on and select the programme you
want.
Watching VCR1. Use the TV/AV button on the remote control to
select AV1 or AV2.- If both S-VIDEO and VIDEO sockets have been
connected to the S-VHS VCR simultaneously, onlythe S-VIDEO can be received.
2. Insert a video tape into the VCR and press thePLAY button on the VCR.(See VCR ownerÕs manual)
S-VIDEO
AUDIO VIDEO
MONITOROUTPUT
A/VINPUT1
AUDIO
R L
AntennaAC IN
VIDEO
INPUT 2COMPONENT
INPUT 1COMPONENT
RGB INPUT
R L/MOND
Apartments(connecting to wall antenna socket)
Private house(connecting to wall outdoor antenna)
outdoor antenna
wall antenna socket
VHF antenna
UHF antenna
RF coaxial wire (75 ohms)< Back panel of the set >
< Back panel of the set >
< VCR >
- 8 -
Watching Cable TV- After subscribing for a local cable TV station and installing a converter you can watch cable TV.- For further information of cable TV, contact the local cable TV station.
To watch cable TV
1. Use the TV/AV button on the remote control toselect AV1 or AV2.
2. Tune to cable service provided channels usingthe cable box.
Watching external AV source- When connecting the set to an external source, match the colours of AUDIO/VIDEO input jacks on the set with the output jacks
on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red.
How to use1. Use the TV/AV button on the remote control to
select AV1 or AV2.2. Operate the corresponding external equipment.
See external equipment operating guide.
S-VIDEO
AUDIO VIDEO
MONITOROUTPUT
A/VINPUT1
AUDIO
R L
An
VIDEO
INPUT 2COMPONENT
INPUT 1COMPONENT
AUDIO INPUT RGB INPUT
R L/MOND
R LAUDIO VIDEO
S-VIDEO
AUDIO VIDEO
MONITOROUTPUT
A/VINPUT1
AUDIO
R L
AntennaAC INP
VIDEO
INPUT 2COMPONENT
INPUT 1COMPONENT
RGB INPUT
R L/MOND
< Back panel of the set >
< Cable box >
< Back panel of the set >
Camcorder
Video game set
- 9 -
Watching DVD
How to connectConnect DVD video outputs to Y, PB, PR of COMPO-NENT INPUT and audio outputs to Audio sockets ofAUDIO INPUT.
How to use1. Turn on the DVD player, and insert a DVD.2. Use TV/AV or MULTIMEDIA button on the remote
control to select Component 1 or Component 2. Refer tothe DVD player's manual for operating instructions.
¥ Component Input portsYou can get better picture quality if you connectDVD player with component input ports as below.
Component ports of theset
Y PB PR
Video output ports of DVD player
YYYY
PbB-YCbPB
PrR-YCrPR
S-VIDEO
AUDIO VIDEO
MONITOROUTPUT
A/VINPUT1
AUDIO
R L
AntennaAC INPU
VIDEO
INPUT 2COMPONENT
INPUT 1COMPONENT
UT RGB INPUT
R L/MOND
R
R R
R
< Back panel of the set >
< DVD player >
Watching DTV (option)- To watch digitally broadcast programs, purchase and connect a digital set-top box.
How to connect1. Use the monitorÕs COMPONENT (Y, PB, PR) INPUT, RGB or DVI
jack for video connections, depending on your set-top box con-nector. Then, make the corresponding audio connections.
How to use1. Turn on the digital set-top box. (Refer to the ownerÕs manual for
the digital set-top box.) 2. Use TV/AV or MULTIMEDIA on the remote control to select
Component 1, Component 2 or RGB.
RS-232C INPUT(CONTROL/SERVICE)
DVI INPUT
S-VIDEO
AUDIO VIDEO
MONITOROUTPUT
A/VINPUT1
AUDIO
R L
VIDEO
INPUT 2COMPONENT
INPUT 1COMPONENT
AUDIO INPUT RGB INPUT
R L/MOND
(R) AUDIO (L) Y PB RP(R) AUDIO (L) DTV OUTPUT
R
R R
RR
¥ DTV Input signal
576p(50Hz)
1080i(50Hz)
1152i(50Hz)
ModeTerminal Component
o
o
o
RGB (DTV)
o
o
o
< Back panel of the set >
< Digital Set-top box >
- 10 -
Connecting PC- To enjoy vivid picture and sound, connect a PC to the set.- Avoid keeping a fixed image on the setÕs screen for a long period of time. The fixed image may become permanently imprinted on
the screen; use a screen saver when possible.- Connect PC to the RGB INPUT(PC INPUT) or DVI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output of
PC accordingly.- There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC
mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until thepicture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to themanufacturer of the PC graphic card.
- The synchronization input form for Horizontal and Vertical frequencies is separate.
Setup Instructions to Connect a PC to your set- We recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality.- If the resolution of PC is over UXGA, there will be no picture on the set.- Connect the signal cable from the set output port of the PC to the RGB INPUT port of the set or the signal cable from the DVI out-
put port of the PC to the DVI INPUT port on the set.- Connect the audio cable from the PC to the Audio input on the set. (Audio cables are not included with the set).- If using a sound card, adjust PC sound as required.- This set apply a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC adjusts
automatically to use this set.- DDC protocol is preset for RGB (Analog RGB), DVI (Digital RGB) mode.- If required, adjust the set settings for Plug and Play functionally.- If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI
INPUT to display the PC on the set.If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or DVI; (the other modeis set to Plug and Play automatically by the set.)
- DOS mode may not work depending on video card if using a DVI-I cable.
232C INPUTTROL/SERVICE)
DVI INPUT
AU
AUDIO
R L
VIDEO
INPUT 2COMPONENT
INPUT 1COMPONENT
AUDIO INPUT RGB INPUT
R
PC Setup1. Turn on the PC and apply power to the set.2. Turn on the display by pressing the POWER button on
the setÕs remote control.3. Use the TV/AV or MULTIMEDIA button on the remote
control to select the RGB or DVI input source.4. Set the resolution output of the PC to SXGA or under
(1280 x 1024, 60Hz). (Refer to p. 13)
< Back panel of the set >
- 11 -
RGB / DVI mode
Resolution
640x350
720x400
640x480
848x480
800x600
HorizontalFrequency(KHz)
VerticalFrequency(Hz)
852x480
832x624
1024x768
1152x864
1152x870
1280x960
1280x1024
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
31.500
37.799
39.375
31.500
37.799
39.375
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.677
54.348
63.995
67.500
77.487
68.681
60.023
63.981
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
60.00
70.00
75.00
60.00
70.00
75.00
56.25
60.31
72.18
75.00
85.06
74.55
60.00
70.06
75.02
85.00
60.05
70.01
75.00
85.00
75.06
60.02
60.02
- 12 -
D-sub 15 pin cable
AS mark
LG TV
OwnerÕs Manual
1.5V1.5V
Alkaline batteries
Power Cord
POWERMUTE
TV/AV MULTIMEDIA
LIST ARC MENU
PR
PR
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM PIP/DW SLEEP
REVEAL TEXT/PIP PR+
WIN. SIZE MIXPIP PR-
POSITION TIMESWAP
HOLD INDEXPIP INPUT
?
i
I/II
Remote Control handset
DVI-D Cable
- Optional extras can be changed or modified for quality improvement without any notification new optional extras can beadded.
- Contract your dealer for buying these items.
Optional Extras
Tilt wall mounting bracket
404250 40 42 50
Video cables Audio cablesCeiling mounting bracket
40
4250
42
40
- Secure the TV assembly by attaching it to a wall for additional support.
Attaching the TV assembly to the wall
¥ Install the TV brackets on the TV as shown.Insert the 2 bolts and tighten securely, in the upper holes on the bracket. Install the wall brackets on the wall with 4 bolts*, (not supplied with the prod-uct), as shown.Match the height of the TV brackets and the wall brackets. Check to be sure the brackets are tightened securely.
¥ Secure the TV assembly to the wall with strong strings or wound wire cables,(not supplied with the product), as shown.
2-TV brackets2-Wall brackets
2-TV bracket bolts
- 13 -
SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.
V Application RangeThis spec is applied to the 42ÓPDP TV used RF-043B Chassis.
V Specification
Each part is tested as below without special appointment.1) Temperature : 25¡ 5¡C (77¡ 9¡F)2) Relative Humidity: 65¡ 10%3) Power Voltage: Standard Input voltage (100V~240V@ 50/60Hz)
* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in
accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.
V Test and Inspection Method1) Performance : LGE TV test method followed.2) Demanded other specification
Safety: CE, IEC specificationEMC : CE, IEC
V General Specification
1. General Specification
Appliance
TEST
TEST
Remark
Safety : IEC/EN60095
EMI : EN55013
EMS : EN55020
Safety : IEC60065
EMI : CISPR13
Model Name
RT-42PX10
RZ-42PX10
Market
EU
Non-EU
Remark
PDP
Maker : NBK / Mitsui / LG Chemical
LGE SPEC
Maker : SONY / Murata / Sanken
Specification
42 inch wide Color Display Module
16:9
PDP42V6xxxx,RGB Closed Type
45% Total light transmittance (E- Mesh)
1) Temp : 0~40 deg
2) Humidity : 0~85%
1) Temp : -20~60 deg
2) Humidity : 0~85%
AC100 ~ 240V, 50/60Hz
No
1
2
3
4
5
6
7
Item
Display Screen Device
Aspect Ratio
PDP Module
Screen Filter
Operating Environment
Storage Environment
Input Voltage
2. Model Specification
(1) RZ-42PX10
(2) RT-42PX10
Item
Market
Broadcasting
Receiving system
Scart Jack ( 3EA )
Video Input(2EA)
S-Video Input(2EA)
Component Input(1EA)
RGB Input(1EA)
DVI Input(1EA)
Audio Input(4EA)
Wired Control
Specification
EU
PAL B/G/I/D/K, SECAM L/L
Upper Heterodyne
PAL, SECAM
PAL, SECAM, NTSC
PAL, SECAM, NTSC
Y/Cb/Cr, Y/Pb/Pr
RGB-PC
DVI-PC
PC Audio, Component,AV(2EA)
Discrete IR
Remark
4 System :
PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60
4 System :
PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60
DVI-D
L/R Input
- 14 -
No
8
9
10
11
12
13
14
15
16
17
18
Remark
4 System :
PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60
4 System :
PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60
4 System :
PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60
DVI-D
L/R Input
Specification
Non-EU
PAL B/G/I/D/K, NTSC
Upper Heterodyne
PAL, SECAM, NTSC
PAL, SECAM, NTSC
PAL, SECAM, NTSC
Y/Cb/Cr, Y/Pb/Pr
RGB-PC
RGB-DTV(for Australian)
DVI-PC
PC Audio, Component,AV(2EA),
AV(2EA)
Discrete IR
No
19
20
21
22
23
24
25
26
27
28
29
Item
Market
Broadcasting
Receiving system
Video Input(2EA)
Video Output(1EA)
S-Video Input(2EA)
Component Input(2EA)
RGB Input
DVI Input
Audio Input(5EA)
Wired Control
- 15 -
1. Application RangeThe spec sheet is applied all of the 42ÓPDP TV, RF-043Bchassis by manufacturing LG TV Plant or sort plants.
2. Specification(1) Because this is not a hot chassis, it is not necessary to
use an isolation transformer. However, the use of isolationtransformer will help protect test instrument.
(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of
25±5¡C of temperature and 65±10% of relative humidity ifthere is no specific designation.
(4) The input voltage of the receiver must keep 100~220V,50/60Hz.
(5) The receiver must be operated for about 15 minutes priorto the adjustment.
O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.
O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full WHITE
PATTERN.
[ Set is activated HEAT-RUN without signal generator inthis mode.
[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.
Caution) If you turn on a still screen more than 20 minutes(Especially digital pattern, cross hatch pattern), a afterimage may be occur in the black level part of thescreen.
3. PCB assembly adjustment method
3-1. Channel memory
(1) Setting up the G-prove1) Install the GProve. (GProve4.4.0.2.exe)2) After installing the Gprobe, [Option -> Connection
Setup] or click the icon indicated in the picture and thensetup as below the picture.(In case of the port (second one), set to the serial port of the connected PCThe other only have to be set as below the picture.)
3) After finishing inputs, click the button [OK] to completethe connection setup.
(2) Confirming the G-prove1) Connect Rs232 cable and then turn on the power.
if communication is correct, the message is showed like in the left output terminal.
2) If the message is not showed, push the [INSTART]button of the adjust remocon twice, and change theright selection of the [System Control -> RS-232 Host]from GProbe to PC.** If it is impossible to check the OSD, push the [TILT]
button of the adjust remocon.Then, the message which is ÒStarting Gprove...Ó comes up. From this time, communication is operated correctly.However, you have to push the [TILT] button again in case of turning on Main Power.
** If you want to check again whether communication ison or not, input ÒtestÓ and push the Enter key on theright input terminal. If communication is on, themessage of ÒTest passed.Ó will come up
(3) Channel memory method1) Click [Command -> Batch].2) When the window of [Batch] is showed, enter the text file
(Ch_Memory-RZ_PX10.txt) in the right blank of the File.3) Click the button [OK] to write CH information in the
EEPROM.4) It means the completion of the CH memory download that
the message of right output terminal is showed as below.
ADJUSTMENT INSTRUCTIONS
fig1
fig2
fig3
3-2. HDCP download
(1) Setting up & Confirming the G-prove: refer to 3-1-(1) and 3-1-(2)
(2) HDCP download method1) Click [Command -> NVRAM Write]2) When the window of [NVRAM Write] is showed, select
ÒLGEKEY1.binÓ to insert fill up in the File.3) LGEKEY1 : first KEY value4) Address : insert Ô0Õ5) After finishing inputs, click the button [OK] to write
HDCP key in the EEPROM.6) It means the end of the HDCP key download that the
message of Output terminal is showed as below.
4. SET assembly adjustment method
4-1. POWER PCB Assy Voltage Adjustments(Va, Vs Voltage Adjustments)
(1) Test Equipment : D.M.M 1EA
(2) Connection Diagram for Measuring : refer to fig5
(3) Adjustment Method1) Adjustment method of P/No 3501V00180A B/D
1. Va Adjustmenta. After receiving 100% Full White Pattern, HEAT RUN.b. Connect + terminal of D.M.M to Va pin of P805,
connect - terminal to GND pin of P805.c. After turning RV 501, voltage of D.M.M adjustment
as same as Va voltage which on label of panelright/top (Deviation; ±0.5V)
2. Vs Adjustmenta. Connect + terminal of D.M.M to Vs pin of P805,
connect Ð terminal to GND pin of P805.b. After turning RV 401, voltage of D.M.M adjustment
as same as Va voltage which on label of panelright/top. (Deviation; ±0.5V)
2) Adjustment method of P/No 3501V00182A B/D1. Va Adjustment
a. After receiving 100% Full White Pattern, HEAT RUN.b. Connect + terminal of D.M.M to Va pin of P805,
connect - terminal to GND pin of P805.c. After turning RV 601, voltage of D.M.M adjustment
as same as Va voltage which on label of panelright/top (Deviation; ±0.5V)
2. Vs Adjustmenta. Connect + terminal of D.M.M to Vs pin of P805,
connect Ð terminal to GND pin of P805.b. After turning RV 401, voltage of D.M.M adjustment
as same as Va voltage which on label of panelright/top. (Deviation; ±0.5V)
4-2. Adjustment of White Balance
(1) Required EquipmentColor Analyzer (CA-100 or same product)
(2) Connection Diagram of Equipment for Measuring
(3) Adjustment of White BalanceO Operate the Zero-calibration of the CA-100, then stick
sensor to PDP module surface when you adjust.O For manual adjustment, it is also possible by the
following sequence.
- 16 -
fig4
< 3501V00180A >
< 3501V00182A >
fig5.connection Diagram of power adjustment for measuring
Each PCB Assy must be checked by the Check JIG Set beforewhole assembly. (Be careful the POWER PCB Assy not todamage to PDP Module)
Window
MSPG-2100 orMSTG-5200
AV Signal Input
Full Size pattern
216 gray Level
RS-232C Serial Communication
RZ/RT 50Hz
fig6 White Balance Adjustment
1) Select white pattern of heat-run mode by pressing poweron key on remote control for adjustment then operateheat run more than 15 minute.
2) Supply 2 Gray Pattern (216 Level Full Size Pattern)signal to VIDEO input.(RZ-42PX10 : AV4 INPUT 50Hz,RT-42PX10 : AV2 INPUT 50Hz)(refer to Fig6)
3) To adjust, stick sensor to 216 Gray Level Pattern, pressADJ key twice(White Balance) on remote control.For adjustment and D , E on remote control foradjustment mode to select Red Gain and Blue Gain,press VOL +, - Key and adjust it until color coordinationbecomes as below.
X ; 0.283 ± 0.003, Y; 0.297 ± 0.003,Color Temperature; 9,300¡K ± 500¡K
4) Exit adjustment mode using A Key.
4-3. Auto RGB Color Balance
(1) Pattern Equipment : PC Pattern Generator (VG828, VG854, 801GF, MSP3240A)(16 Gray Scale Pattern output(RGB output Level: 0.7Vp-p)
(2) Method of Auto RGB Color Balance 1) Input RGB Source : 16 Gray Scale Pattern output
(RGB output Level : 0.7Vp-p)2) Press ADJ KEY on R/C for adjustment. 3) Press Vol. + KEY and operate To set.4) Auto-RGB OK means completed adjustment.
4-4. Auto Component Color Balance
(1) Pattern Equipment : MSP3240A or same product(16 Gray Scale Pattern output(Component outputLevel: 0.7Vp-p)
(2) Method of Auto RGB Color Balance 1) Input RGB Source : Component 480p/576p 16 Gray
Scale Pattern outputAt this time, except Pb and Pr signal, only Y signal insert.2) Press ADJ KEY on R/C for adjustment. 3) Press Vol. + KEY and operate To set.4) Auto-RGB OK means completed adjustment
4-5. Auto Adjustment Map(RS-232C)
4-6. DDC Data Input(1) Required Test Equipment
1) A jig for adjusting PC, DDC (PC serial to D-subConnection equipment)
2) S/W for writing DDC (EDID Data Write & Read)3) D-sub 15P Cable, D-Sub to DVI Connector (Connect to DVI Jack)
(2) Setting of Device
(3) Preparation for Adjustment1) Set devices as above and turn the PC, jig on.2) Put S/W for writing DDC (EDID data Write & Read) into
operation. (operated in DOS mode.)
(4) Sequence of Adjustment1) DDC Data Input for Analog-RGB
1. Put the set on the table and turn the power on.2. Connect PC Serial to D-sub 15P Cable of jig for DDC
adjustment to RGB terminal (D-Sub 15Pin).3. Operate S/W for DDC record and select DDC data for
Analog RGB in Model Menu.4. Operate EDID Write command.5. Operate EDID Read command and check whether
Check Sum is 53.6. If Check Sum is not 53, repeat 3 ~ 4.7. If Check Sum is 53, DDC data for Analog-RGB input
is completed.
2) DDC Data input for Digital-RGB(DVI)1. Connect PC Serial to DVI Cable of jig for DDC
adjustment to DVI terminal (DVI Jack).2. Operate S/W for DDC record and select DDC Data
for digital RGB in Model Menu.3. Operate EDID Write command. 4. Operate EDID Read command and check whether
Check Sum is D2(1page), BF(2page).5. If Check Sum is not D2(1page), BF(2page), repeat 3 ~ 4.6. If Check Sum is D2(1page), BF(2page), DDC data for
Analog-RGB input is completed.
- 17 -
fig7 Auto RGB/Component Color Balance Test Pattern
Type
Baud Rate
115200
Index
R Gain
G Gain
B Gain
R Offset
G Offset
B Offset
Data bit
8
Cmd1 Cmd2
j a
j b
j c
j d
j e
j f
Stop bit
1
Parity
NONE
ProtocolSetting
Data Min Value
00(00)
00(00)
00(00)
00(00)
00(00)
00(00)
Max Value
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
RF-043B_PDP42
PCPC
JIGJIG
PDPPDP
SETSET
- 18 -
TROUBLE SHOOTING GUIDE
1. Power Board
1-1. The whole flowchart which it follows in voltage output state
Start check
Manufacture enterprisemeaning of a passage
1. Check the Power Offcondition.
Doesn't the screen whole come
out?
It is identical with Power Off
condition?
Yes
Yes
No
No
No
No
No
2. Check the Interfacesignal condition.
Is the Interface signal operated?
Yes
3. Check the St-by 5Vsignal circuit.
Doesn't the low pressure output
come out?
Doesn't the St-by 5V signal
come out?
Yes
Yes
No
4. Check the 5V Monitorsignal circuit.
Doesn't the 5V Monitor signal
come out?
Yes
7. Check the VSC Vs-ONsignal
Doesn't the high tension output
come out?
Doesn't the VSC signal Vs-ON
come out?
Yes
Yes
High tension output voltage Drop
it occurs?
When remove the
Y B/D Module Input Connector, output
voltage Drop it occurs?
When remove the Y, Z B/D Module
Input Connector, Power Board high tension output
voltage Drop it occurs?
Yes No No
9. Check the PowerBoard Output high
tension circuit
Yes
10. Check the Z B/DModule Coutput circuit
Yes
When remove the
Z B/D Module Input Connector, output
voltage Drop it occurs?
11. Check the Y B/DModule Coutput circuit
Yes
No
8. Check the Vs, Vavoltage output circuit.
Doesn't the Vs, Va voltage output
come out?
Yes
No
No
5. Check the VSC RL-ONsignal.
Doesn't the VSC signal RL-ON
come out?
Yes
6. Check the VSC lowpressure output
Doesn't the VSC low pressureoutput come out?
Yes
- 19 -
1-2. Sony Power Board Structure
T502: Vs Trans
T702: Va Trans
T101: St-by Trans
T103: Low Voltage Trans
1 2 3
- 20 -
1-3. Sanken Power Board Structure
T221: Vs Trans
T271: Va Trans
T121: St-by Trans
T201: Low Voltage Trans
1 2 3
- 21 -
2. No Power
(1) Symptom¯ DoesÕt minute discharge at module. ¯ Non does not come in into the front LED.
(2) Check follow
Is plug in power cord? Plug in power cord.
Yes
No
Is connect the Line Filter and PowerSwitch Cable?
Connect Cable.
Yes
No
Is connect the Power Switch andPower Board Cable?
Connect Cable.
Yes
No
Is normal the Fuse(F101) on PowerBoard?
Replace Fuse.
Yes
No
Is connect the Power Board and 7Pof VSC Board Cable?
Connect Cable.
Yes
No
Is connect the Power Switch andPower Board Cable?
After remove the cable connect toPower Board(except the CN101
connection cable), authorizes theAC voltage marking on manual.
When ST-BY 5V does not operate,replace Power Board.
Connect Cable.
Yes
No
- 22 -
3. Protect Mode
(1) Symptom¯ After once shining, it does not discharge minutely
from module¯ The Rely falls(The sound is audible ÒclickÓ) ¯ It is converted with the color where the front LED
is red from green.
(2) Check follow
Is normal the PowerBoard?
Replace PowerBoard.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is normal the eachconnector?
Replaceconnector.
Replace Y-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is normal the Ctrl Board?
Replace X-Board.
Is normal the output voltage afterremove P1, 2, 101, 300, 701, 702
connector of Ctrl-B/D?
Yes
No Yes
Is normal the Y- Board?
Is normal the outputvoltage after removeP5, P6 connector of
Y-B/D?
Is normal the Fuse(F52) on Y-B/D?(In case of open is replace)
Yes
No Yes Yes
Replace Z-Board.
Is normal the Z- Board?
Is normal the outputvoltage after remove
P1 connector of Z-B/D?
Is normal the Fuse(FS1, FS2) on Z-B/D? (In case of open is replace)
Yes
No Yes
Is normal the X- Board?
Is normal the output voltage afterremove P1, 2, 3, 4, 6, 7 connector of
X-B/D?
After remove P1, P2, P3, P4 output voltagenormality: Replace Right X-B/DAfter remove P6, P7 output voltagenormality: Replace Left X-B/D
Yes
No Yes
Is normal the VSC Board?
Is normal the output voltage afterremove P1000, P1200?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1000 normal operation:Replace Analog BoardAfter remove P1200 normal operation:Replace Digital Board
Yes
No
Is normal the COF of X, Y, Z?
No
Yes
Yes
- 23 -
4. No Raster
(1) Symptom¯ DoesÕt minute discharge at module. ¯ It maintains the condition where the front LED is green.
(2) Check follow
Is normal the PowerBoard?
Replace PowerBoard.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is normal the eachconnector?
Replaceconnector.
Replace Y-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is normal the Ctrl Board?
Replace X-Board.
Is normal the output voltage afterremove P1, 2, 101, 300, 701, 702
connector of Ctrl-B/D?
Yes
No Yes
Is normal the Y- Board?
Is normal the outputvoltage after removeP5, P6 connector of
Y-B/D?
Is normal the Fuse(F52) on Y-B/D?(In case of open is replace)
Yes
No Yes Yes
Replace Z-Board.
Is normal the Z- Board?
Is normal the outputvoltage after remove
P1 connector of Z-B/D?
Is normal the Fuse(FS1, FS2) on Z-B/D? (In case of open is replace)
Yes
No Yes
Is normal the X- Board?
Is normal the output voltage afterremove P1, 2, 3, 4, 6, 7 connector of
X-B/D?
After remove P1, P2, P3, P4 output voltagenormality: Replace Right X-B/DAfter remove P6, P7 output voltagenormality: Replace Left X-B/D
Yes
No Yes
Is normal the VSC Board?
Is normal the output voltage afterremove P1000, P1200?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1000 normal operation:Replace Analog BoardAfter remove P1200 normal operation:Replace Digital Board
Yes
No
Is normal the COF of X, Y, Z?
No
Yes
Yes
- 24 -
5. In case of occur strange screen into specific mode
5-1. In case of doesÕt display the OSD
(1) Symptom¯ LED is green¯ The minute discharge continuously becomes
accomplished from module
(2) Check follow
Is normal the LVDScable?
Is normal the VSCDigital Board?
Is the LVDS cableconnected well?
Cable inserts well.Yes
No
No
Yes
Operates the ThineIC(IC1100)?
Replace ThineIC(IC1100).
No
Is normal the CtrlBoard of Module?
Replace Ctrl B/D.No
No
Operates theIEP(IC500)?
ReplaceIEP(IC500).
Yes
No
Operates theScaler(IC700)?
ReplaceScaler(IC700).
Yes
Replace cable.Yes
- 25 -
5-2. In case of doesÕt display the screen into specific mode
(1) Symptom¯ The screen does not become the display from specific input mode
(RF, AV, Component, RGB, DVI).
(2) Check follow¯ Check the all input mode should become normality display.¯ Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become
normality display from the PIP mode or DW mode. (Re-Check it Swap)
(3) In case of becomes unusual display from RF mode
(4) In the case of becomes unusual display from RF, AV mode
Is normal the Tuner?
Is normal theCXA2069Q?
Is the Tuner Cableconnected well?
Cable inserts well.
Yes
No
No
Yes
Is normal theVPC3230?
Replace Tuner
No
Is normal the Input voltage, IICCommunication and CVBS output?
Yes
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal theCXA2069Q?
Yes
Is normal theVPC3230?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
- 26 -
(5) In the case of becomes unusual display from RF, AV, Component 480i mode
(6) In the case of becomes unusual display from Component DTV mode
Is normal theVPC3230?
Yes
Is normal the S2300?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the74LS123?
Yes
Is normal theCXA2101?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal theM52758?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
- 27 -
(7) In the case of becomes unusual display from RGB DTV mode
(8) In the case of becomes unusual display from RGB PC mode
(8) In the case of becomes unusual display from DVI mode
Is normal theCXA2101?
Yes
Is normal theM52758?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal theM52758?
Yes
Is normal the Scaler?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
- 28 -
6. In case of no sound
(1) Symptom¯ LED is green¯ Screen display but sound is not output
(2) Check follow
Is normal the SPKcable?
Is the SPK cableconnected well?
Cable inserts well.
No
No
Cable inserts well.
No
Replace IC800
No
Replace IC801
No
Replace SPK cableYes
Yes
Is normal theRGB/DVI sound?
Is the Flat cableconnected well?
No
No
Operates the IC800?Yes
Operates the IC801?
Replace IC802
No
Operates the IC802?Replace
VSC Analog B/D
Yes
Yes
Yes
Is normal theRF/AV/Component
sound?
- 29 -
BLOCK DIAGRAM
RG
B( P
C/D
TV)
DV
I( P
C/D
TV)
RS
23
2
IR
74A
CT
253
RX
0/1
,TX
0/1
IRTX
SC
L/S
DA
RG
B H
/V
SC
L/S
DA
RX
/TX
0/1
/2,
RX
/TX
C
ST
32
32
C
24L
C2
1
74
HC
T0
8
24
LC
21
CX
A2
10
1
Sca
rt1
Sca
rt2
Sca
rt3
RF
CV
BS
S-V
HS
CX
A2
06
9Q
SW
ITC
HT
un
er (
M)
Tu
ne
r(S
)
Vin
1 ( C
VB
S)
VP
C3
23
0 ( M
)V
ide
o D
eco
der
VP
C3
23
0 ( S
)V
ide
o D
ecod
er
1H R
GB
Vin
2 ( C
VB
S)
MN
T O
UT
TV
OU
T
Vin
3 ( C
VB
S) T
U_M
ain
TU
_Su
b
Vin
4
YC
in4
Ma
in_V
Ma
in_Y
C
Ma
in_V
Ma
in_Y
C S
DA
60
01
Text
Pro
cess
or
Te
xt_V
HY
V6
41
62
0S
RA
M
AM
29
LV
16
0F
-RO
M
74L
S1
23
Co
mp
_48
0i
M5
27
58
FS
wit
ch
S2
30
0D
eIn
terl
ac
er
YC
bC
r/ 8
HY
57
V6
43
22
SD
RA
M (
8M
B)
RG
B P
C/D
TV
RG
B P
C
RG
B D
TV
gm
16
01
Sc
ale
r (M
ali
bu
)C
omp
DT
V
CX
A_R
GB
RG
B_D
ata
Ma
in_V
ide
o / 24
Su
b_V
ide
o/ 8
DV
I_D
ata
TX
_Ou
t
RS
23
2_R
X/T
X
Co
mp
/RG
B_S
WF
rom
Ma
lib
u
Dig
ita
l
An
alo
g
Sid
e-A
V
CV
BS
S-V
HS
Vin
5Y
Cin
5C
om
p_Y
Co
mp
_48
0I/
PT
o M
ali
bu
Vid
eo
fo
r T
ext
Te
xtT
X0
/1/2
/3/C
Dis
p_E
nS
DA
TA
SC
LK
, S
LE
HY
5D
U2
83
22
2A
SD
RA
M (
12
8M
B)
AM
29
LV
F-R
OM
(1
MB
)
Co
mp
/RG
B_S
W
Co
mp
_48
0I/
P
Po
st-p
roc
es
sin
g B
loc
k is
om
itte
d.
so-
ca
lle
d J
EP
ICO
, in
th
is c
as
eT
MD
S T
X i
s a
lso
re
qu
ire
d.
So
un
d P
roc
es
sin
g B
loc
k D
iag
ram
is s
ep
ara
ted
..R
CA-
typ
e B
loc
k D
iag
ram
is
als
o
se
pa
rate
d..
DV
I R
Xw
/HD
CP
AD
Cw
/PL
L
IEP
24
24
24
24 1
0
WIR
E
ZH
INE
Co
mp
1( D
D/ D
TV
)V
BO
AR
D
BO
AR
D
BO
AR
D
BLOCK DIAGRAM
- 30 -
RG
B(P
C/D
TV
)
DV
I(P
C/D
TV
)
RS
23
2
IR
ST
32
32
C
74A
CT
25
3
74H
CT
08
Tx
gm
15
01
H2
4LC
21
24L
C2
1
RG
B P
C
IIS IIS
IIS
CX
A2
10
1C
XA
21
01
RG
B D
TV
HV
M5
27
58
FP
IC2
02
(MU
X)
M5
27
58
FP
IC2
02
(MU
X)
M5
27
58
FP
IC2
04
M5
27
58
FP
IC2
04
RG
B_D
TV
FL
I23
00
FL
I23
00
HY
57
V6
43
22
SD
RA
M (
8M
B)
HY
57
V6
43
22
SD
RA
M (
8M
B)
DA
C_R
GB
Co
mp
1( D
VD
/DT
V)
RF
CV
BS
IN
Sid
e
S-V
HS
An
alo
g
CV
BS
OU
T
Sid
e-C
VB
S
Co
mp
2( D
VD
/DT
V)
TQ
FP
12
8K
DD
R M
em
ory
TQ
FP
12
8K
DD
R M
em
ory
Fla
sh
RO
M5
12
K/1
MF
las
h R
OM
51
2K
/1M M
62
32
0F
P(I
2C
Exp
en
de
r)
M6
23
20
FP
(I2
C E
xpe
nd
er)
CX
A2
06
9Q
UP
D6
40
83
UP
D6
40
83
VP
C3
23
0 (M
AIN
)V
PC
32
30
(MA
IN)
VP
C3
23
0 (S
UB
)V
PC
32
30
(SU
B)
DV
D_S
UB
DT
V_C
om
p
M5
27
58
FP
IC4
00
(MU
X)
M5
27
58
FP
IC4
00
(MU
X)
DV
D_M
AIN
DV
D2
_MA
IN
DV
D2
_SU
B
DT
V2
_Co
mp
S-V
HS
Tu
ne
r (M
)
Tu
ne
r (S
)
VIN
1
Y/C
IN1
Co
mp
Co
mp
2
MN
T_O
UT
VIN
2
Y/C
IN2
MA
IN_V
OU
T
SU
B_C
OU
T
SU
B_Y
OU
T
CA
B_V
IN
MA
IN_Y
OU
T
MA
IN_C
OU
T
LA
71
51
MS
W C
VB
S/Y
CO
MB
_YO
UT
CO
MB
_CO
UT
AL
T_Y
_48
0I_
MA
IN
AL
T_Y
_48
0I_
SU
B
AL
T_Y
2_4
80
I_M
AIN
AL
T_Y
2_4
80
I_S
UB
S/D
VD
_Co
mp
M3
71
36
(OT
P)
M3
71
36
(OT
P)
CA
B_C
om
b
MA
IN_Y
OU
T
M6
56
8 B
it
S6
56
8 B
it
Sid
e A
/V
TM
DS
Tra
ns
fer
/Th
ine
LV
DS
31
PIN
RG
B_2
4B
it
An
alo
g
RG
B
DV
I
VP
OR
T(2
4b
it)
SV
PO
RT
(16
bit
)
IEP
ZH
INE
WIR
E
Dig
talB
OA
RD
BO
AR
D
MEMO
- 31 -
- 32 -
EXPLODED VIEW
300
301
304
302
202206
203
204
201
205
580
400
401#
410
402
520
560
530
531
570
121
601600
120
490
207
200
303
305
- 33 -
120 6401VD0013B SPEAKER ASSEMBLY, FULL RANGE(L) . RZ-42PX10 L
121 6401VD0013A SPEAKER ASSEMBLY, FULL RANGE(R) . RZ-42PX10 R
200 6348Q-E050C PDP, 42Ó 16:9 852*480 PDP42V60000.AKLGG
201 6871QCH034A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42V6 NEW MCM(1222) LVDS
202 6871QDH066A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V6 YDRV TOP HAND INSERT ASSY
203 6871QDH067A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V6 YDRV BTM HAND INSERT ASSY
204 6871QLH034A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42V6_XL(4LAYER)
205 6871QRH037A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42V6_XR(4LAYER)
206 6871QYH029A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42V6
207 6871QZH033A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42V6
300 3091V00645A CABINET ASSEMBLY, RZ-42PY20
301 4980V01067A SUPPORTER, ASSY AL FILTER TOP RZ-42PZ10
302 4980V01068A SUPPORTER, ASSY AL FILTER BOTTOM RZ-42PX10
303 4980V01069A SUPPORTER, ASSY AL FILTER RIGHT RZ-42PX10
304 4980V01070A SUPPORTER, ASSY AL FILTER LEFT RZ-42PX10
305 3790V00281G FILTER(MECH), RZ-42PX10 NBK 1142G03EK-M6 AR/NIR MESH GLASS 3 LAYER
400 3809V00444A BACK COVER ASSEMBLY RZ-42PY20
401 3301V00025D PLATE ASSEMBLY, ASSY COVER VSC TUNER RU-42PX10 PRESS
402 3301V00023D PLATE ASSEMBLY, ASSY AV VSC TUNER RU-42PX10
410 4980V01071A SUPPORTER, ASSY AL MODULE. RZ-42PX10
490 4980V01057A SUPPORTER, PCB EGI POWER SW. RZ-42PY20
520 6871VMMS17A PWB(PCB) ASSEMBLY,MAIN RF043B MALIBU RT MAIN DIGITAL MANUAL
530 6871VSME92A PWB(PCB) ASSEMBLY,SUB PSW RF043A MAILBU
531 5020V00915A BUTTON, POWER RZ-42PY20 ABS 1KEY .
560 6871VSMS05A PWB(PCB) ASSEMBLY,SUB TUNER RF043B MALIBU RT SUB ANALOG MANUAL
570 6871VSMZ91A PWB(PCB) ASSEMBLY,SUB CONT RF043A NEW HOLDER LOCAL KEY KODENSI
580 3501V00180A BOARD ASSEMBLY, POWER RZ-42PX10 RF043A 1H201W1 SANKEN PSU
600 6871VSME91A PWB(PCB) ASSEMBLY,SUB A/V RF043A MALIBU SIDE AV
601 4811V00118B BRACKET ASSEMBLY, DECO RU-42PX10 RF043A SIDE AV
EXPLODED VIEW PARTS LIST
No. Part No. Description
M62320FP,I/O EXPANDER 16P SOP TP
AT24C02N-10SI-2.7 ATMEL 8P SOIC
KA7809R, FAIRCHILD 2P D-PAK
MIC39100 MICREL 3P SOT223
PQ05DZ1U SHARP 5, SMD TYPE
TK11840L 8P SOT23L
PQ05DZ1U SHARP 5, SMD TYPE
AT24C02N-10SI-2.7 ATMEL 8P SOIC
SN74HCT08D TEXAS INSTRUMENT 16P
SN74LVTH541PWR 20P TSSOPUT
SN74LVTH541PWR 20P TSSOPUT
THC63LVD103 64P TQFP
SC1565IST-1.8 SEMTECH 3P SOT223 TP
MIC39100 MICREL 3P SOT223
KA7809R, FAIRCHILD 2P D-PAK
BA033FP-E2 ROHM 3P-SOP,TO252-3
PQ05DZ1U SHARP 5, SMD TYPE
PQ05DZ1U SHARP 5, SMD TYPE
BA033FP-E2 ROHM 3P-SOP,TO252-3
SC1565IST-1.8 SEMTECH 3P SOT223 TP
BA033FP-E2 ROHM 3P-SOP,TO252-3
MIC39100 3P SOT223 R/TP LDO TYPE 2.5V
74ACT253SC FAIRCHILD 16P SOIC
ST3232CDR SGS-THOMSON SOP16
M52758FP MITSUBISHI 36PIN
DM74LS123MX 16SOP TP
DM74LS123MX 16SOP TP
CXA2069Q QFP64 BK I2C BUS AV S/W
CXA2101AQ 80P,QFP BK
SN74HCT08D 16P R/TP QUADRUPLE
LGDT4410 LG IC 176P TQFP
SDA6001 QH B12 128P MQFP
HY57V641620HGT-H HYNIX 54P TSOPII
MX29LV160ATTC-70 MACRONIX 48P TSOP
AT24C16AN-10SI-2.7 ATMEL 8P SOIC
KIA7027AF 3, SOT-89 TP RESET IC 2.7V
FLI2300BD GENESIS 208P PQFP
M52758FP MITSUBISHI 36PIN, R/TP PLL IC
VPC3230D C5 80P QFP
HY57V643220C(L)T-6 HYNIX 86P TSOP
VPC3230D C5 80P QFP
GM1501HBD GENESIS 416P PBGA
AT24C32AN-10SI-2.7 8PIN SOP TP 32K 3.3V
KIA7042AF SOT-89 TP 4.2V
MSP4410G-QA-C13-101
HY5DU283222AQ-5 HYNIX 100P LQFP
NSP-6241B NEOFIDELITY 64P TQFP
MX29LV800TTC-70 48PIN,TSOP
TAS5122DCAR 56P/TSSOP
KIA7042AF SOT-89 TP 4.2V
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION
Q001
Q002
Q100
Q100
Q1000
Q101
Q101
Q102
Q102
Q103
Q103
Q104
Q105
Q106
Q107
Q108
Q110
Q111
Q1200
Q1201
Q1202
Q207
Q208
Q209
Q210
Q211
Q214
Q215
Q216
Q217
Q218
Q219
Q300
Q301
Q302
Q303
Q304
Q305
Q306
Q307
Q308
Q309
Q310
Q311
Q312
Q313
Q314
Q315
Q316
Q317
Q318
0TR387500AA
0TR387500AA
0TR150400BA
0TR830009BA
0TRKE80038A
0TR387500AA
0TR830009BA
0TR387500AA
0TR830009BA
0TR150400BA
0TR830009BA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR830009BA
0TR830009BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR104009AF
0TR387500AA
0TR150400BA
0TR104009AF
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
BSS83 TP PHILIPS N-CHANNEL S/W TR
KTC3552T-RTK KEC R/TP SOT-23F 50V 3A
CHIP 2SC3875S(ALY) KEC
BSS83 TP PHILIPS N-CHANNEL S/W TR
CHIP 2SC3875S(ALY) KEC
BSS83 TP PHILIPS N-CHANNEL S/W TR
CHIP 2SA1504S(ASY) KEC
BSS83 TP PHILIPS N-CHANNEL S/W TR
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP KRC104S SOT-23 TP KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP KRC104S SOT-23 TP KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
LOCA. NO PART NO DESCRIPTION
IC100
IC100
IC1000
IC1001
IC1002
IC1003
IC1004
IC101
IC102
IC103
IC104
IC1100
IC1200
IC1201
IC1202
IC1300
IC1301
IC1302
IC1303
IC1304
IC1305
IC1306
IC200
IC201
IC202
IC203
IC204
IC400
IC401
IC402
IC500
IC500
IC501
IC502
IC503
IC504
IC600
IC600
IC601
IC601
IC700
IC700
IC701
IC702
IC800
IC800
IC801
IC801
IC802
IC805
0IMI623200B
0IMMRAL014B
0IMCRFA010A
0IPRPML001A
0IMCRSH001A
0ITK118100B
0IMCRSH001A
0IMMRAL014B
0IMCRTI003A
0IMCRTI021A
0IMCRTI021A
0IMCRTH002A
0IMCRSJ001A
0IPRPML001A
0IMCRFA010A
0IMCRRH001A
0IMCRSH001A
0IMCRSH001A
0IMCRRH001A
0IMCRSJ001A
0IMCRRH001A
0IPRPML001A
0IFA742530B
0IMCRSG010A
0IMCRMI006A
0IFA741230A
0IFA741230A
0ISO206900A
0ISO210100B
0IMCRTI003A
0ICTMLG018A
0IMCRMN023A
0IMMRHY001F
0IMMRMR006B
0IMCRAL006A
0IKE702700D
0IMCRGN002C
0IMCRMI006A
0IIT323000E
0IMMRHY033A
0IIT323000E
0IPRPGN012A
0IMMRAL025A
0IKE704200J
0IMCRMN028A
0IMMRHY020B
0IMCRNL001A
0IMMRMR023A
0IMCRTI028C
0IKE704200J
IC TRANSISTOR
- 34 -
- 35 -
LOCA. NO PART NO DESCRIPTION
Q319
Q320
Q321
Q400
Q400
Q401
Q401
Q402
Q402
Q403
Q404
Q405
Q406
Q600
Q800
Q801
Q802
D100
D100
D1000
D1001
D1002
D1003
D1004
D101
D101
D102
D103
D104
D105
D116
D117
D118
D119
D120
D1200
D1201
D1206
D121
D122
D123
D124
D125
D126
D127
D128
D129
D130
D1300
D1301
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD184009AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD184009AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
KDS184S CHIP 85V 300MA KEC TP
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
KDS184S CHIP 85V 300MA KEC TP
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
LOCA. NO PART NO DESCRIPTION
D1302
D1303
D1304
D1305
D1306
D131
D200
D201
D202
D203
D204
D205
D500
D501
D502
D503
LD001
LD1000
LD1001
LD1002
LD1003
LD1203
LD1204
LD1206
LD1207
ZD100
ZD101
ZD102
ZD103
ZD104
ZD105
ZD400
ZD401
ZD800
C002
C1001
C1002
C1003
C1004
C1006
C1016
C1017
C1018
C102
C1020
C1022
C1025
C1027
C1031
C1037
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DL200000CA
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DZ820009AH
0CE4763F618
0CE107SF6DC
0CE227VF6DC
0CE107SF6DC
0CE475SK6DC
0CE477SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE475SK6DC
0CE107SF6DC
0CE477SF6DC
0CE475SK6DC
0CE107SF6DC
0CE477SF6DC
0CE477SF6DC
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
LED,SAM5670(DL-2LRG) BK Y-GREEN -
LED,SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
LED,SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
LED,SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
LED,SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
LED,SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
LED,SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
LED,SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
LED,SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
MTZJ8.2B TP ROHM-K DO34 - 8.2V 5UA -
47UF SRE 16V M FL TP5
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
4.7UF MVG 50V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
4.7UF MVG 50V 20% SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
4.7UF MVG 50V 20% SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
DIODE
CAPACITOR
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
- 36 -
LOCA. NO PART NO DESCRIPTION
C104
C1041
C1042
C1045
C1046
C105
C1052
C1058
C1059
C106
C1060
C1061
C1063
C1066
C1066
C1067
C107
C1072
C1074
C1077
C1079
C108
C1082
C110
C111
C112
C113
C114
C120
C1202
C1205
C1206
C121
C121
C1211
C1212
C1215
C1216
C1218
C1220
C1229
C1233
C124
C1249
C1250
C1251
C1254
C1256
C1257
C1259
C127
C1273
0CE476DF618
0CE107SF6DC
0CE477SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476DF618
0CE107SF6DC
0CE107SF6DC
0CE477DJ618
0CE227VF6DC
0CE227VF6DC
0CE107SF6DC
0CE227VF6DC
0CE107SF6DC
0CE476SF6DC
0CE477DJ618
0CE477SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477SF6DC
0CE107SF6DC
0CE227VF6DC
0CE475SK6DC
0CE477SF6DC
0CE106SF6DC
0CE475SK6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE477SF6DC
0CE476SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE227VF6DC
0CE477SF6DC
0CE227VF6DC
0CE227VF6DC
0CE477SF6DC
0CE107SF6DC
0CE227VF6DC
0CE227VF6DC
0CE477SF6DC
0CE227VF6DC
0CE227VF6DC
0CE227VF6DC
0CE227VF6DC
0CE475SK6DC
0CE476SF6DC
47UF STD 16V M FL TP5
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF STD 16V M FL TP5
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
470UF STD 35V 20% FL TP 5
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF STD 35V 20% FL TP 5
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
4.7UF MVG 50V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
4.7UF MVG 50V 20% SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
4.7UF MVG 50V 20% SMD R/TP
47UF MVG 16V M SMD R/TP
LOCA. NO PART NO DESCRIPTION
C1274
C1275
C1279
C1305
C1314
C1315
C1317
C1331
C1333
C1353
C1355
C1362
C1366
C1368
C1373
C1374
C1384
C1388
C1391
C1400
C1402
C1404
C1410
C1415
C1425
C208
C209
C210
C222
C222
C223
C223
C224
C224
C230
C251
C254
C258
C261
C263
C272
C274
C276
C288
C289
C300
C301
C303
C315
C316
C317
C322
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE107SF6DC
0CE227VF6DC
0CE227VF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE107SF6DC
0CE106SF6DC
0CE477SF6DC
0CE106SF6DC
0CE476SF6DC
0CE476XFKDC
0CE476SF6DC
0CE476XFKDC
0CE476SF6DC
0CE476XFKDC
0CE107SF6DC
0CE106SF6DC
0CN105EJ56A
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE106SF6DC
0CN105EJ56A
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
47UF MVK-BP,CN 16V 20%,-20%
47UF MVG 16V M SMD R/TP
47UF MVK-BP,CN 16V 20%,-20%
47UF MVG 16V M SMD R/TP
47UF MVK-BP,CN 16V 20%,-20%
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
1.0UF 3216 35V 10% R/TP X7R
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
1.0UF 3216 35V 10% R/TP X7R
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
- 37 -
LOCA. NO PART NO DESCRIPTION
C324
C334
C335
C400
C401
C402
C404
C406
C410
C423
C429
C435
C440
C442
C502
C505
C506
C507
C508
C509
C517
C520
C522
C523
C525
C527
C529
C534
C601
C605
C607
C608
C611
C612
C614
C626
C627
C632
C634
C637
C651
C702
C703
C710
C713
C720
C723
C727
C737
C744
C752
C757
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE227VF6DC
0CE476SF6DC
0CE107SF6DC
0CE227VF6DC
0CE476SF6DC
0CE107SF6DC
0CE105SK6DC
0CE107SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE105SK6DC
0CE106SF6DC
0CE476SF6DC
0CE106SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CE226SF6DC
0CE106SF6DC
0CE106SF6DC
0CE226SF6DC
0CE226SF6DC
0CE106SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
1UF MVG 50V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
1UF MVG 50V M SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
22UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
LOCA. NO PART NO DESCRIPTION
C762
C769
C777
C778
C785
C800
C801
C802
C803
C812
C817
C822
C825
C827
C828
C829
C834
C834
C837
C840
C841
C847
C851
C852
C862
C863
C872
C873
C874
L1004
L1005
L1006
L1007
L1200
L1203
L1209
L1213
L803
L804
L805
L806
AR500
AR503
AR507
AR508
AR509
AR512
AR513
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE335SK6DC
0CE226SF6DC
0CE226SF6DC
0CE476SF6DC
0CE226VF6DC
0CE226VF6DC
0CE226SF6DC
0CE107SF6DC
0CE335SK6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CN105EJ56A
0CE108DH618
0CE108DH618
0CF4741L438
0CF4741L438
0CE335SK6DC
0CN105EJ56A
0CE108DH618
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0022A
6140VB0022A
6140VB0022A
6140VB0022A
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
3.3UF MVG 50V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
47UF MVG 16V M SMD R/TP
22UF MV 16V 20% R/TP(SMD) SMD
22UF MV 16V 20% R/TP(SMD) SMD
22UF MVG 16V 20% SMD R/TP
100UF MVG 16V M SMD R/TP
3.3UF MVG 50V 20% SMD R/TP
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
1.0UF 3216 35V 10% R/TP X7R
1000UF STD 25V M FL TP5
1000UF STD 25V M FL TP5
0.47UF D 63V 5% TP 5 M/PE NI
0.47UF D 63V 5% TP 5 M/PE NI
3.3UF MVG 50V 20% SMD R/TP
1.0UF 3216 35V 10% R/TP X7R
1000UF STD 25V M FL TP5
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
CPS-0810 GET 22UH 21.5TURNS
CPS-0810 GET 22UH 21.5TURNS
CPS-0810 GET 22UH 21.5TURNS
CPS-0810 GET 22UH 21.5TURNS
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
COIL
RESISTOR
- 38 -
LOCA. NO PART NO DESCRIPTION
AR522
AR600
AR600
AR601
AR601
AR602
AR602
AR603
AR603
AR604
AR605
AR606
AR607
AR608
AR609
AR610
AR611
AR612
AR613
AR614
AR615
AR616
AR617
AR618
AR700
AR701
AR701
AR702
AR703
AR707
AR708
AR709
AR710
AR711
AR712
AR713
AR714
AR715
AR717
AR718
AR719
R801
R802
SW001
SW002
SW003
SW004
SW005
SW006
SW700
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RKZVTA001L
0RKZVTA001L
140-315A
140-315A
140-315A
140-315A
140-315A
140-315A
140-313B
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
1.0M OHM 1/2 W 5% TA52
1.0M OHM 1/2 W 5% TA52
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT 2LEAD 160G(TA) LG C&D
LOCA. NO PART NO DESCRIPTION
SW800
L100
L100
L1000
L1001
L1002
L1008
L1009
L101
L101
L1010
L1011
L1012
L1013
L1014
L1015
L1016
L1017
L1018
L1019
L102
L102
L103
L103
L104
L105
L105
L106
L107
L108
L1206
L1207
L1210
L1211
L1216
L1217
L1300
L1302
L1307
L1310
L1311
L1312
L1313
L1314
L1315
L1316
L1317
L1318
L1321
L1322
6600VM2006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6200JB8010L
6200JB8010L
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
SDDF3PATP011 250V 4A HORIZONTAL .G
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
SWITCH
FILTER & CRYSTAL
- 39 -
LOCA. NO PART NO DESCRIPTION
L1325
L1326
L1327
L1328
L1329
L1330
L1331
L1332
L1333
L200
L201
L202
L203
L204
L204
L205
L205
L206
L206
L207
L207
L208
L208
L209
L210
L211
L212
L213
L214
L214
L215
L215
L216
L216
L217
L300
L301
L302
L303
L304
L305
L400
L400
L401
L401
L402
L403
L404
L405
L406
L407
L500
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6200JB8013L
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0005A
6210VC0006A
6210VC0005A
6210VC0006A
6210VC0005A
6210VC0006A
6210VC0005A
6210VC0006A
6210VC0005A
6210VC0006A
6210VC0005A
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0005A
6210VC0005A
6210VC0005A
6210VC0006A
6210VC0006A
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
BEAD FEELUX R/TP 60 OHM TB201209U060
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
FBMH3216 HM501NT 3.2X1.6X1.6MM
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
LOCA. NO PART NO DESCRIPTION
L501
L502
L503
L504
L505
L506
L507
L609
L700
L800
L807
L808
R102
R103
R106
R107
R108
X500
X600
X600
X700
X700
X800
JK103
JK200
JK201
JK202
P101
P102
P200
P201
A1
A2
A3
A4
A5
A6
A7
A8
A9
F801
PA001
TU100
TU101
P100
P200
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6202VDT002K
6202VDB007B
6202VDT002J
6202VDB007B
6202VDT002B
156-A02M
6613V00026A
6612VJH020B
6612VJH020C
6612VJH019B
380-068E
6612BBBHN6A
380-363G
380-068E
3828VA0468D
6710V00126R
6410VEH003C
6850VA0004J
6851V00022C
3550V00338A
6850J00003A
6850J00004A
6866VA9001B
0FS1002B53K
6712000002B
6700MF0010A
6700MF0010B
6630VGA001C
6630VGA004B
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
RESONATOR,SX-1 6MHZ +/- 30 PPM 16PF TP .
RESONATOR,HC49U 20.250MHZ 30PPM 13PF BK
RESONATOR,SX-1 13.500000MHZ +/- 50 PPM 14PF
RESONATOR,HC49U 20.250MHZ 30PPM 13PF BK
RESONATOR,SX-1 SC14.3MHZ +/- 30 PPM
RESONATOR,HC49U 18.432MHZ 30PPM 10PF BK
UJB-03-28A UGCOM 6613V00004S
PPJ122B PARK ELEC. A/V 6P
PPJ122C PARK ELEC. A/V 6P
PPJ121B PARK ELEC. A/V 4P
UEJ-CV-018 UGCOM D3.5 E/P
440062-1 AMP DVI INTERACED
6046B-01S PARKELEC H=8.0
UEJ-CV-018 UGCOM D3.5 E/P
MANUAL,OWNERS RF043B 126R TX 026H 7YRS
REMOTE CONTROLLER,RF043A PIP RZ-42PY20
POWER CORD,M2511A-001 VDE/SEMKO 2800MM
CABLE,COAXIAL UL1365#26 150MM UCA-EX-069
CABLE,COAXIAL(150MM),UL1365#26 VW-1
COVER,TX 6710V00091 ABS SPRAY #76
CABLE,DVI-D TO DVI-D UL20276 AWG28 3000MM
CABLE,LVDS UL20276 AWG30 500MM
CONNECTOR, 2990-9C UL 1161 AWG 26 TWI
FUSE,10000MA 250 V 5.2X20
REMOTE CONTROLLER RECEIVER,KSM-603SM12E-1
TUNER,TAUM-W501P 4 SYSTEM MAIN
TUNER,TAFM-W502P 4SYSTEM SUB
CONNECTOR,68114-1521 15PIN 2.29MM
CONNECTOR,69107-0921 9P 2.77MM
JACK
ACCESSORIES
MISCELLANEOUS
UNER(BOTTOM)
SIDE A/V(TOP)SIDE A/V(BOTTOM)
CONTROL(TOP)
CONTROL(BOTTOM)
Jun., 2004Printed in KoreaP/NO : 3828VD0161E