riface installation guide - riedel communications · 1.1550290 riface g2 mtm800e duplex remove the...

2
Riedel Communications GmbH & Co. KG | Uellendahler Str. 353 | 42109 Wuppertal | Germany www.riedel.net 21.01.2013 | Rev 0.2 Slide the radio in the rack and plug 7. the audio cables (left cable faces left, right cable faces right). Turn the top plate to the back side 2. and unplug the grounding connector from the grounding terminal on the top plate. Unplug carefully both audio cables 3. from the PCB connector. Remove both screws of the 4. connector PCB. Slide the locking PCB in the notch of 5. the radio connector. Plug the connector PCB on the radio 6. connector and fix it on the locking PCB. Remove the 13 screws on the top. 1. This guide describes the steps to install the radios in the RiFace rack. A T10 Torx driver and a 4mm hexagon driver are required for the assembly. All different radio types are mounted in the same way. Only the connectors can vary in type. Following table shows the different RiFace versions with the compatible radios. RiFace Radios 1550200 RiFace G2 GM360 Simplex 1550210 RiFace G2 GM360 Duplex Motorola GM360/GM340/CM360/Pro5100/CDM1550 1550220 RiFace G2 CM300 Simplex 1550230 RiFace G2 CM300 Duplex Motorola CM300/CM340/CM360 1550240 RiFace G2 DM3400 Simplex 1550250 RiFace G2 DM3400 Duplex Motorola DM3400/DM3600/XPR4550 1550260 RiFace G2 MTM700 Simplex 1550270 RiFace G2 MTM700 Duplex Motorola MTM700/MTM800 1550280 RiFace G2 MTM800e Simplex 1550290 RiFace G2 MTM800e Duplex Motorola MTM800e RiFace Installation Guide

Upload: others

Post on 26-Oct-2020

6 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: RiFace Installation Guide - Riedel Communications · 1.1550290 RiFace G2 MTM800e Duplex Remove the 13 screws on the top. This guide describes the steps to install the radios in the

Riedel Communications GmbH & Co. KG | Uellendahler Str. 353 | 42109 Wuppertal | Germany www.riedel.net

21.0

1.20

13 |

Rev

0.2

Slide the radio in the rack and plug 7. the audio cables (left cable faces left, right cable faces right).

Turn the top plate to the back side 2. and unplug the grounding connector from the grounding terminal on the top plate.

Unplug carefully both audio cables 3. from the PCB connector.

Remove both screws of the 4. connector PCB.

Slide the locking PCB in the notch of 5. the radio connector.

Plug the connector PCB on the radio 6. connector and fix it on the locking PCB.

Remove the 13 screws on the top.1.

This guide describes the steps to install the radios in the RiFace rack.

A T10 Torx driver and a 4mm hexagon driver are required for the assembly.

All different radio types are mounted in the same way. Only the connectors can vary in type. Following table shows the different RiFace versions with the compatible radios.

RiFace Radios1550200 RiFace G2 GM360 Simplex1550210 RiFace G2 GM360 Duplex

Motorola GM360/GM340/CM360/Pro5100/CDM1550

1550220 RiFace G2 CM300 Simplex1550230 RiFace G2 CM300 Duplex

Motorola CM300/CM340/CM360

1550240 RiFace G2 DM3400 Simplex1550250 RiFace G2 DM3400 Duplex

Motorola DM3400/DM3600/XPR4550

1550260 RiFace G2 MTM700 Simplex1550270 RiFace G2 MTM700 Duplex

Motorola MTM700/MTM800

1550280 RiFace G2 MTM800e Simplex1550290 RiFace G2 MTM800e Duplex

Motorola MTM800e

RiFace Installation Guide

Page 2: RiFace Installation Guide - Riedel Communications · 1.1550290 RiFace G2 MTM800e Duplex Remove the 13 screws on the top. This guide describes the steps to install the radios in the

Riedel Communications GmbH & Co. KG | Uellendahler Str. 353 | 42109 Wuppertal | Germany www.riedel.net

21.0

1.20

13 |

Rev

0.2

Plug the grounding connector on 14. grounding terminal on the top plate.

Fix the top plate with the 13 screws.15.

Check the TXext Jumper 13. (closer informations can be found in the RiFace manual)

... that the radios are placed at the 11. back end.

Fix both antenna cables with a 12. cable tie.

Fix the radios with screws on the 10. right and left side in the middle, upper notch in that way, ...

Plug the antenna cable in the radio 9. (upper cable to left, lower cable to right).

Plug the power cable in the radio 8. (rear cable to left, front cable to right).

RiFace Installation Guide