rfid system v680 series - omron automation...
TRANSCRIPT
RFID System
V680 Series
Cat. No.: Z248-E1-03A
Amplifier and Antennas
V680-HA63BV680-HS52V680-HS63V680-HS65
ID Tags
V680-D2KF52MV680-D2KF67V680-D2KF67MV680-D8KF68V680-D32KF68
User's Manual for Amplifiers, Antennas, and ID Tags(FRAM)
Introduction
Thank you for purchasing a V680-series RFID System. This manual describes the functions, performance,
and application methods needed for optimum use of the V680-series RFID System.
Please observe the following items when using the RFID System.
• Allow the RFID System to be installed and operated only by qualified specialist with a sufficient
knowledge of electrical systems.
• Read and understand this manual before attempting to use the RFID System and use the RFID Sys-
tem correctly.
• Keep this manual in a safe and accessible location so that it is available for reference when required.
Intro
du
ction
Sectio
n 1
Sectio
n 2
Sectio
n 3
Sectio
n 4
Sectio
n 5
Introduction
Section 1
Section 2
Section 3
Section 4
Section 5
R
P
S
C
In
C
RFID V680-V680-V680-V680-V680-V680-V680-V680-V680-
User'
EAD AND UNDERSTAND THIS DOCUMENT
roduct Overview
pecifications and Performance
ommunications Specifications
stallation
hemical Resistance
SystemHA63B AmplifierHS52 AntennaHS63 AntennaHS65 AntennaD2KF52M ID TagD2KF67 ID TagD2KF67M ID TagD8KF68 ID TagD32KF68 ID Tag
s Manual
2
Intro
du
ction
Introduction
READ AND UNDERSTAND THIS DOCUMENTPlease read and understand this document before using the products. Please consult your OMRON representative if you have any questions or comments.
WARRANTYOMRON’s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)
from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FIT-
NESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITYOMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN
ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABIL-
ITY.
In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON’S
ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CON-
TAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
SUITABILITY FOR USETHE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED. THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF
PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES. Please refer to sep-
arate catalogs for OMRON's safety rated products.
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer’s applica-
tion or use of the product.
At the customer’s request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the prod-
ucts. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine,
system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses
of the products, nor is it intended to imply that the uses listed may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document.
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government regulations.
• Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PERFORMANCE DATAPerformance data given in this document is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the
result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty
and Limitations of Liability.
CHANGE IN SPECIFICATIONSProduct specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However,
some specifications of the product may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key spec-
ifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased prod-
ucts.
DIMENSIONS AND WEIGHTSDimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
ERRORS AND OMISSIONSThe information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical,
or proofreading errors, or omissions.
PROGRAMMABLE PRODUCTSOMRON shall not be responsible for the user’s programming of a programmable product, or any consequence thereof.
COPYRIGHT AND COPY PERMISSIONThis document shall not be copied for sales or promotions without permission. This document is protected by copyright and is intended solely for use in con-
junction with the product. Please notify us before copying or reproducing this document in any manner, for any other purpose. If copying or transmitting this
document to another, please copy or transmit it in its entirety.
RFID SystemUser's Manual
Intro
du
ction
Introduction
Alert Symbols for Safe Use
The following symbols are used in this manual to indicate precautions that must be observed to ensure safe
use of the V680-HS63, V680-HS52, V680-HS65, V680-HA63B, V680-D2KF67, V680-D2KF67M, V680-
D2KF52M, V680-D8KF68, and V680-D32KF68. The precautions provided here contain important safety infor-
mation. Be sure to observe these precautions.
The following signal words are used in this manual.
Meanings of Alert Symbols
Warning
Safety Precautions
Indicates a potentially hazardous situation which, if not avoided, will result in minor or mod-
erate injury, or may result in serious injury or death. Additionally, there may be significant
property damage.
Indicates general prohibitions for which there is no specific symbol.
These Products are not designed to be used either directly or indirectly in applications that detect human
presence for the purpose of maintaining safety. Do not use these Products as a sensing means for protecting
human lives.
WARNING
WARNING
3RFID System
User's Manual
4
Intro
du
ction
Introduction
The Products conform to the following overseas regulations and standards.
1. The United States
FCC NOTICEThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC WARNINGChanges or modifications not expressly approved by the party responsible for compliance could void the user's author-ity to operate the equipment.Do not remove the ferrite core (TDK Type ZCAT1730-0730A) installed on the cables to suppress RF interference.
2. Europe
Regulations and Standards
Amplifier Antenna
This product complies with Part 15 Subpart C of the FCC Rules.FCC ID: E4E6CYSIDV6800306
V680-HA63B V680-HS52V680-HS63V680-HS65
Amplifier Antenna
(Radio and Telecommunication Terminal Equipment Directive 1999/5/EC) V680-HA63B V680-HS52V680-HS63V680-HS65
Radio:
EMC:
Safety:
EN 300 330-2V1.3.1 (04-2006)EN 300 330-1V1.5.1 (04-2006)EN 301 489-3V1.4.1 (08-2002)EN 301 489-1V1.6.1 (09-2005)EN 61010-1: 2001 (2nd Edition)
English Hereby, Omron, declares that the RFID System, V680-HS52 Series, V680-HS63 Series, V680-HS65 Series, and V680-HA63B Series are in compliancewith the essential requirements and other relevant provisions of Directive 1999/5/EC.
Finnish Omron vakuuttaa täten että RFID Säännös, V680-HS52 Series, V680-HS63 Series, V680-HS65 Series, V680-HA63B Series tyyppinen laite on direktiivin1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Dutch Hierbij verklaart Omron dat het toestel de RFID Systeem, V680-HS52 ´Serie, V680-HS63 ´Serie, V680-HS65 ´Serie, V680-HA63B ´Serie in overeen-stemming is met de essentiële eisen en de andere relevante bepalingen van richtlijh 1999/5/EG.
French Par la présente Omron déclare que la RFID Système, V680-HS52 Série, V680-HS63 Série, V680-HS65 Série, V680-HA63B Série sont conforme aux exi-gences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Swedish Härmed intygar Omron att den RFID System, V680-HS52 Serie, V680-HS63 Serie, V680-HS65 Serie V680-HA63B Serie stär l överensstämmelse medde väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Danish Undertegnede Omron erklærer herved, at følgende den RFID System, V680-HS52 Serie, V680-HS63 Serie, V680-HS65 Serie, 680-HA63B Serie over-holder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
German Hiermit erklärt Omron, die RFID System, V680-HS52 Serie, V680-HS63 Serie, V680-HS65 Serie, V680-HA63B Serie in Übereinstimmung mit dengrundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. (BMWi)
Greek ME THN ΠAPOYSA Omron ∆HΛONEI RFID O’YO’ΓΗΜΑ, V680-HS52 O’EIPA, V680-HS63 O’EIPA, V680-HS65 O’EIPA V680-HA63B O’EIPA SYM-MOPF ONETAI ΠPOS TIS OYSIO∆EIS AΠAITHSEIS KAI TIS ΛOIΠES SXETIKES ∆IATAΞEIS THS O∆HΓIAS 1999/5/EK.
Italian Con la presente Omron dichiara che la RFID Sistema, V680-HS52Serie, V680-HS63 Serie, V680-HS65 Serie, V680-HA63B Serie sono conforme ai req-uisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Spanish Por medio de la presente Omron declara que el RFID Sistema, V680-HS52 Serie, V680-HS63 Serie, V680-HS65 Serie, V680-HA63B Serie esta conformea los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Portuguese Omron declara que a RFID Sistema, V680-HS52 Série, V680-HS63 Série, V680-HS65 Série, V680-HA63B Série ser conforme com os tequisitos essenci-ais e outras disposições da Directiva 1999/5/CE.
Romanian Prin prezenta, Omron declar c acest V680-HS52,V680-HS63,V680-HS65, V680-HA63B este conform cu cerin ele principale çi cu celelalte prevederirelevanate ale Directivei 1999/5/EC.
RFID SystemUser's Manual
Intro
du
ction
Introduction
3. Japan
4. Canada
This device complies with RSS-Gen of IC Rules.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) thisdevice must accept any interference received, including interference that may cause undesired operation.
5. China
6. Korea
Amplifier Antenna
Equipment using high frequencies: Inductive Reading/Writing Communications EquipmentConforming standards: Inductive Reading/Writing Communications Equipment; Standard: ARIB STD-T82EC-06020
V680-HA63B V680-HS52V680-HS63V680-HS65
Amplifier Antenna
IC ID:850J-V68HA63B V680-HA63B V680-HS52V680-HS63V680-HS65
Amplifier Antenna
CMII ID:2007DJ0576 V680-HA63B V680-HS52-R
CMII ID:2007DJ0574 V680-HA63B V680-HS52-W
CMII ID:2007DJ0572 V680-HA63B V680-HS63-W
CMII ID:2007DJ0570 V680-HA63B V680-HS63-R
Amplifier Antenna
OMR-V680-HA63B V680-HA63B V680-HS52-RV680-HS52-WV680-HS63-RV680-HS63-W
5RFID System
User's Manual
6
Intro
du
ction
Introduction
7. Taiwan
8. Hong Kong
9. Singapore
10.Malaysia
If the product is used in Malaysia, a label must be attached on-site to the side of the V680-HA63B.
Please consult your OMRON sales representative for details.
11.Philippine
12.Mexico
Este equipo opera a titulo secundario, consecuentemente, debe aceptar interferencias perjudiciales incluyendoequipos de la misma clase y puede no causar interferencias a sistemas operando a titulo primario.
13.ThailandThe certification is unnecessary, so the product can be used.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's author-ity to operate the equipment.Do not remove the ferrite core (TDK Type ZCAT1730-0730A) installed on the cables to suppress RF interference.
Amplifier Antenna
CCAB07LP1220T4 V680-HA63B V680-HS52V680-HS63
Amplifier Antenna
LP407042 V680-HA63B V680-HS52V680-HS63
Amplifier Antenna
S0293-07 V680-HA63B V680-HS52V680-HS63
Amplifier Antenna
A011579 V680-HA63B V680-HS52V680-HS63
Amplifier Antenna
ESD-0702971C V680-HA63B V680-HS52V680-HS63
Amplifier Antenna
COFETEL:RCPOMV607-329 V680-HA63B V680-HS52V680-HS63
RFID SystemUser's Manual
Intro
du
ction
Introduction
Be sure to observe the following precautions to ensure safe use of the Products.
1. Do not use the Products in environments with flammable, explosive, or corrosive gasses.
2. Do not attempt to disassemble, repair, or modify any Product.
3. Tighten mounting screws securely.
4. Because a cable has a locking mechanism, make sure that it has been locked before using the cable.
5. Do not allow water or pieces of wire to enter from openings in the case. Doing so may cause fire or
electric shock.
6. Turn OFF the Controller power supply before mounting or removing an Antenna or Amplifier.
7. If an error is detected in any Product, immediately stop operation and turn OFF the power supply.
Consult with an OMRON representative.
8. Dispose of the Products as industrial waste.
9. Observe all warnings and precautions given in the body of this manual.
10. Do not touch the product immediately after usage at high temperatures. Doing so may occasionally
result in burning.
Precautions for Safe Use
7RFID System
User's Manual
8
Intro
du
ction
Introduction
Always observe the following precautions to prevent operation failures, malfunctions, and adverse effects on
performance and equipment.1. Installation Environment
Do not use the Products in the following locations.
• Locations exposed to corrosive gases, dust, metallic powder, or salts• Locations not within the specified operating temperature range• Locations subject to rapid changes in temperature or condensation• Locations not within the specified humidity range• Locations subject to direct vibration or shock outside the specified ranges• Locations subject to spray of water, oil, or chemicals
2. InstallationThe Products communicate with Tags using the 13.56-MHz frequency band. Some motors, inverters,
and switching power supplies generate noise that can affect communications with the Tags and cause
errors. If such devices are located near the Tags, always test operation in advance to confirm whether
the system will be affected.
• Observe the following precautions to minimize the effects of normal noise.(1) Ground all metal objects in the vicinity of the Products to 100 Ω or less.(2) Do not use the Products near high-voltage or high-current lines.
• Do not use non-waterproof Products in an environment where mist is present.• Do not expose the Products to chemicals that adversely affect the Product materials.• When mounting the Products, tighten the screws to the following torques.V680-HS63: 1.2 N⋅mV680-HS52: 40 N⋅mV680-HS65: 1.2 N⋅m
• Transmission will not be possible if the front and back panels are mistakenly reversed and the Unit ismounted to a metallic surface.V680-D2KF67M
• The transmission distance will be reduced when the Unit is not mounted to a metallic surface.V680-D2KF67M
• If multiple Antennas are mounted near each other, communications performance may decrease dueto mutual interference. Refer to Installing Antennas on page 50 and check to make sure there is nomutual interference.
• Depending on the operating environment, the case surface may become fogged, but basic perfor-mance will not be affected.
3. StorageDo not store the Products in the following locations.
• Locations exposed to corrosive gases, dust, metallic powder, or salts• Locations not within the specified storage temperature range• Locations subject to rapid changes in temperature or condensation• Locations not within the specified storage humidity range • Locations subject to direct vibration or shock outside the specified ranges• Locations subject to spray of water, oil, or chemicals
Precautions for Correct Use
RFID SystemUser's Manual
Intro
du
ction
Introduction
4. Cleaning• Do not clean the Products with paint thinner or the equivalent. Paint thinner or the equivalent will dis-
solve the resin materials and case coating.
5. Combination of the AmplifierUse the V680-D2KF67, V680-D2KF67M, V680-D2KF52M, V680-D8KF68, and V680-D32KF68 IDTags in combination with only the V680-HA63B Amplifier. Do not use these ID Tags together with theV680-HA63A Amplifier.
9RFID System
User's Manual
10
Intro
du
ction
Mean
ing
s of S
ymb
ols
Introduction
Meanings of Symbols
Indicates particularly important points related to a function, including precautions and application advice.
Indicates page numbers containing relevant information.
RFID SystemUser's Manual
Intro
du
ction
Introduction
Table of ContentsSafety Precautions 3
Regulations and Standards 4
Precautions for Safe Use 7
Precautions for Correct Use 8
Meanings of Symbols 10
Table of Contents 11
Section 1 Product Overview 13
Features 14
Product Configuration 15
Section 2 Specifications and Performance 17
Antennas with Separate Amplifier 18
Amplifier 24
Tags 27
Section 3 Communications Specifications 35
Communications Distances 36
TAT and Communication Time (Reference) 44
Section 4 Installation 49
Installing Antennas 50
Mounting Amplifiers 55
Installing Tags 57
Section 5 Chemical Resistance 67
Chemical Resistance of the Antennas 68
Chemical Resistance of Tags 69
Degree of Protection 72
Revision History 74
11RFID System
User's Manual
12
Intro
du
ction
Introduction
MEMO
RFID SystemUser's Manual
Sectio
n 1
Pro
du
ct Overvie
Section 1Product Overview
Features 14
w
Product Configuration 15
13RFID System
User's Manual
14
Sectio
n 1
Featu
res
Section 1Product Overview
FeaturesThe V680-series RFID System actively supports many different types of system, such as distributed-control
systems and many-product, small-lot production systems, with non-contact data communications using
electromagnetic induction.
Non-contact Data CommunicationsThe V680 Series uses electromagnetic induction to enable non-contact, bi-directional data communi-
cations between Antennas and Tags.
FRAM MemoryFRAM (non-volatile memory) is used for Tag memory. No battery is required, so there is no need to be
concerned about battery service life.
CRC Used for Transmission Error DetectionA bi-directional 16-bit CRC (Cyclic Redundancy Check) has been added as the error detection method
for wire transmissions between ID Controllers and Antennas, and for wireless transmissions between
Antennas and Tags. This method maintains superior communications reliability even where problems
such as noise occur.
Memory Capacity of 2,000, 8K, or 32K BytesTags have a memory capacity of 2,000, 8K, or 32K bytes. In addition to the ID data required on-site,
data such as model numbers and inspection information can be input.
Long service life: 10 billion accessesThe FRAM memory can be accessed up to 10 billion times (in units of single, 8-byte blocks)
Superior Environmental Resistance and High ReliabilityAntennas and Tags now have greater environmental resistance and are not affected by vibration, oil, or
water.
RFID SystemUser's Manual
Sectio
n 1
Pro
du
ct Co
nfig
uratio
nSection 1
Product Overview
Product ConfigurationA V680-series RFID System consists of an ID Controller, one or more Amplifiers, one or two Antennas, and
Tags. Select the models suitable for the application.
When embedding the V680-D2KF52M into a metal surface, use the V680-HS52 Antenna.
Transmission will not be possible if the V680-HS63 Antenna is used.
Use the V680-D2KF67, V680-D2KF67M, V680-D2KF52M, V680-D8KF68, and V680-D32KF68 ID Tags in combination with only
the V680-HA63B Amplifier. Do not use these ID Tags together with the V680-HA63A Amplifier.
V680-HA63B
V680-HS63
V680-CA5D01-V2
Personal computer Programmable Controller (PLC)
V680-D2KF67 V680-D2KF52MV680-D2KF67M
V680-CA5D02-V2
RS-232C RS-422 RS-485
Hos
t dev
ice
ID C
ontr
olle
r
Am
plifi
ers
Ant
enna
s w
ith S
epar
ate
A
mpl
ifier
Tags
V680-D8KF68/-D32KF68
V680-HS52 V680-HS65
15RFID System
User's Manual
16
Sectio
n 1
Pro
du
ct Co
nfig
uratio
n
Section 1Product Overview
MEMO
RFID SystemUser's Manual
Sectio
n 2
Sp
ec
Section 2Specifications and Performance
Antennas with Separate Amplifier 18
ifications and
Perfo
rman
ce
Amplifier 24
Tags 27
17RFID System
User's Manual
18
Sectio
n 2
An
tenn
as with
Sep
arate Am
plifier
Section 2Specifications and Performance
Antennas with Separate Amplifier
V680-HS63
General Specifications
Dimensions• V680-HS63-W
Item Model V680-HS63-W(Standard cable, waterproof connector)
V680-HS63-R(Flexible cable, non-waterproof connector)
Ambient operating temperature
−10 to 60°C (with no icing)
Ambient storage temperature
−25 to 75°C (with no icing)
Ambient operating humidity
35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. (at 500 VDC) between cable terminals and case
Dielectric strength 1,000 VAC, 50/60Hz for 1 min between cable terminals and case
Degree of protection IP67 (IEC60529)In-house standard for antenna oil resistance (former JEM standard equivalent to IP67g)Note: The connector specifications are IP67 and
IP65 (IEC 60529).
IP67 (IEC60529)In-house standard for antenna oil resistance (former JEM standard equivalent to IP67g)Note: The connectors are not waterproof.
Vibration resistance 10 to 500 Hz, 1.5-mm double amplitude, acceleration: 100 m/s2, 10 sweeps in each of 3 axis directions (up/down, left/right, and forward/backward) for 11 minutes each
Shock resistance 500 m/s2, 3 times each in 6 directions (Total: 18 times)
Dimensions 40 × 53 × 23 mm
Material ABS resin case, epoxy resin filler
Weight Approx. 850 g (with 12.5 m cable)
Cable length Standard lengths of 2 and 12.5 m
(Unit: mm)
235
5
Operation indicator
4028
±0.1
53
27 6
11
Note: Mounting Hole Dimensions
Coil center
Two, M4 or 4.5 dia. holes
37
503016.
5 di
a.
Coaxial cable, 5.5 dia., standard length: 2 m
Connector
Ferrite core
Insulation cover
16.5
dia
.
14.5
dia
.
Antenna
Case material ABS resin
Fill resin Epoxy resin
Cable PVC (gray)
RFID SystemUser's Manual
Sectio
n 2
An
tenn
as with
Sep
arate Am
plifier
Section 2Specifications and Performance
• V680-HS63-RAntenna
23
5
5
4028
±0.
1
53
27 6
11
(Unit: mm)
Operation indicator
Note: Mounting Hole DimensionsCoil center
Two, M4 or 4.5 dia. holes
5030
16.5
dia
.
Coaxial cable, 5.3 dia., standard length: 2 m
Insulation cover
(39.5)Connector
Ferrite core
16.5
dia
.
14.5
dia
.
Case material ABS resin
Fill resin Epoxy resin
Cable PVC (black)
19RFID System
User's Manual
20
Sectio
n 2
An
tenn
as with
Sep
arate Am
plifier
Section 2Specifications and Performance
V680-HS52
General Specifications
Dimensions• V680-HS52-W
Item Model V680-HS52-W(Standard cable, waterproof connector)
V680-HS52-R(Flexible cable, non-waterproof connector)
Ambient operating temperature
−10 to 60°C (with no icing)
Ambient storage temperature
−25 to 75°C (with no icing)
Ambient operatinghumidity
35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. (at 500 VDC) between connector terminals and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between connector terminals and case
Degree of protection IP67 (IEC60529)In-house standard for antenna oil resistance (former JEM standard equivalent to IP67g)Note: The connector specifications are IP67 and
IP65 (IEC 60529).
IP67 (IEC60529)In-house standard for antenna oil resistance (former JEM standard equivalent to IP67g)Note: The connectors are not waterproof.
Dielectric strength 10 to 500 Hz, 1.5-mm double amplitude, acceleration: 100 m/s2, 10 sweeps in each of 3 axis directions
(up/down, left/right, and forward/backward) for 8 minutes each
Shock resistance 500 m/s2, 3 times each in 6 directions (Total: 18 times)
Dimensions M22 × 65 mm
Material ABS resin, brass, and epoxy resin filler
Weight Approx. 850 g (with 12.5 m cable)
Cable length Standard lengths of 2 and 12.5 m
65
47.6
5750
730
19
.8 d
ia.
35 dia.
22.5 dia.
Mounting Hole Dimensions
Two toothed washers
Two lock nuts
M22 × 1
Operation indicator
37
5030
16.5
dia
.
Coaxial cable, 5.5 dia., standard length: 2 m
Connector
Ferrite core
Insulation cover
16.5
dia
.
14.5
dia
.
Antenna
Case material Brass
Communicationssurface
ABS resin
Fill resin Epoxy resin
Cable PVC (gray)
RFID SystemUser's Manual
Sectio
n 2
An
tenn
as with
Sep
arate Am
plifier
Section 2Specifications and Performance
• V680-HS52-R
65
47.6
5750
730
19
.8 d
ia.
35 dia.
22.5 dia.
Mounting Hole Dimensions
Two toothed washers
Two lock nuts
M22 × 1
Operation indicator Insulation cover
5030
16.5
dia
.
Coaxial cable, 5.3 dia., standard length: 2 m
Insulation cover
(39.5)Connector
Ferrite core
16.5
dia
.
14.5
dia
.
Antenna
Case material Brass
Communicationssurface
ABS resin
Fill resin Epoxy resin
Cable PVC (black)
21RFID System
User's Manual
22
Sectio
n 2
An
tenn
as with
Sep
arate Am
plifier
Section 2Specifications and Performance
V680-HS65
General Specifications
Dimensions• V680-HS65-W
Item Model V680-HS65-W(Standard cable, waterproof connector)
V680-HS65-R(Flexible cable, non-waterproof connector)
Ambient operating temperature
−25 to 70°C (with no icing)
Ambient storage temperature
−40 to 85°C (with no icing)
Ambient operatinghumidity
35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. (at 500 VDC) between connector terminals and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between connector terminals and case
Degree of protection IP67 (IEC60529)In-house standard for antenna oil resistance (former JEM standard equivalent to IP67g)Note: The connector specifications are IP67 and
IP65 (IEC 60529).
IP67 (IEC60529)In-house standard for antenna oil resistance (former JEM standard equivalent to IP67g)Note: The connectors are not waterproof.
Dielectric strength 10 to 500 Hz, 1.5-mm double amplitude, acceleration: 100 m/s2, 10 sweeps in each of 3 axis directions
(up/down, left/right, and forward/backward) for 11 minutes each
Shock resistance 500 m/s2, 3 times each in 6 directions (Total: 18 times)
Dimensions 100 × 100 × 30 mm
Material ABS resin case, epoxy resin filler
Weight Approx. 1100 g (with 12.5 m cable)
Cable length Standard lengths of 2 and 12.5 m
Operation indicator
3020 11
(Unit: mm)
16.5
dia.
14.5
dia.
37
5030
16.5
dia
.
Coaxial cable, 5.5 dia., standard length: 2 m
Connector
Ferrite core
Insulation cover
14 1010
Bushing
50
25
10090±0.25
50
100
90±0
.25
4-4.5 dia.(Mounting holes)
Case material ABS resin
Fill resin Epoxy resin
Cable PVC (gray)
RFID SystemUser's Manual
Sectio
n 2
An
tenn
as with
Sep
arate Am
plifier
Section 2Specifications and Performance
V680-HS65-R
(39.5)
16.5
dia.
14.5
dia.
(Unit: mm)
5030
16.5
dia
.
Coaxial cable, 5.3 dia., standard length: 2 m
Insulation cover
Connector
Ferrite core
Operation indicator
3020 11
14 1010
Bushing
50
25
10090±0.25
50
100
90±0
.25
4-4.5 dia.(Mounting holes)
Case material ABS resin
Fill resin Epoxy resin
Cable PVC (black)
23RFID System
User's Manual
24
Sectio
n 2
Am
plifier
Section 2Specifications and Performance
Amplifier
V680-HA63B
General Specifications
Dimensions
Item Model V680-HA63B
Ambient operating temperature
−10 to 55°C (with no icing)
Ambient storage temperature
−25 to 65°C (with no icing)
Ambient operatinghumidity
35% to 85% (with no condensation)
Insulation resistance 20 MΩ min. (at 500 VDC) between cable terminals and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between cable terminals and case.
Degree of protection IP67, IP65 (IEC 60529)Note: Not including connector at Controller end.(When V680-HS63-W or V680-HS52-W is connected)
IP40 (IEC 60529)(When V680-HS63-R or V680-HS52-R is connected)
Dielectric strength 10 to 500 Hz, 1.5-mm double amplitude, acceleration:100 m/s2, 10 sweeps in each of 3 axis directions
(up/down, left/right, and forward/backward) for 11 minutes each
Shock resistance 500 m/s2, 3 times each in 6 directions (Total: 18 times)
Dimensions 25 × 40 × 65 mm (Not including protrusions.)
Materials PC
Weight Approx. 650 g (with 10 m cable)
Cable length Standard lengths of 5 and 10 m
Note: The maximum total cable extension is 50 m (including the Amplifier cable). A maximum of two extension cables can be connected.
Operation indicator
13.7 65 1851
36
15 d
ia.
4025
9.5
dia
.
25
3.5
12
.8 d
ia.
15 35.625
Round, vinyl-insulated cable (5.8 dia.), standard length: 5 m, (41/0.16 dia) 2 conductors, (17/0.08 dia.) 8 conductors
Connector
Connector
Case material PC resin
Cable PVC
RFID SystemUser's Manual
Sectio
n 2
Am
plifier
Section 2Specifications and Performance
Nomenclature
Antenna Connection PortThe Antenna connection port is connected a V680-series Antenna.
Controller ConnectorThe Controller connector is connected to Antenna connection port on the Controller.
Operation Indicators (LEDs)
The distance level will vary greatly depending on the surrounding environment. The setting position will serve as a
guide, but use RUN mode to conduct a sufficient number of tests in the actual operating environment.
Values of distance level 4 or above may not be displayed, but this will not affect the RUN mode performance and does
not indicate a malfunction.
Name Color Meaning
RUN Green Lit when the power is ON.
COMM Yellow Lit when a command is being sent.
NORM Green Lit when communications with a Tag are normal in Normal Communications Mode.
ERR Red Lit when an error occurs in communications with a Tag in Normal Communications Mode.
LV6/7D YellowMaintenance Mode: Lit at distance or speed level 6.Normal Communications Mode: Lit when a write protection error occurs.
LV5/7A YellowMaintenance Mode: Lit at distance or speed level 5 or higher.Normal Communications Mode: Lit when an address error occurs.
LV4/76 YellowMaintenance Mode: Lit at distance or speed level 4 or higher.Normal Communications Mode: Lit when a Tag memory error occurs.
LV3/72 YellowMaintenance Mode: Lit at distance or speed level 3 or higher.Normal Communications Mode: Lit when a no Tag error occurs.
LV2/71 YellowMaintenance Mode: Lit at distance or speed level 2 or higher.Normal Communications Mode: Lit when a verification error occurs.
LV1/70 YellowMaintenance Mode: Lit at distance or speed level 1 or higher.Normal Communications Mode: Lit when a Tag communications error occurs.
Operation indicators
RUNCOMMNORMERR
LV6/7DLV5/7ALV4/76LV3/72LV2/71LV1/70
Antenna connection port
Controller connector
25RFID System
User's Manual
26
Sectio
n 2
Am
plifier
Section 2Specifications and Performance
Cables Specifications
Dimensions
Item Model V700-A43/V700-A44
Number of conductors 10
Insulation resistance 5 MΩ min. (at 500 VDC) between terminals and sheath
Dielectric strength 500 VAC, 1 min
Item Model V700-A43 V700-A44
Length (L1) Approx.10m Approx. 20 m
Weight Approx. 700 g Approx.1,350 g
51 L1±100 49
15.5
dia
.
Connector (Controller end))
Connection label
Connector (Amplifier end)
6 di
a.
15 d
ia.
(Unit: mm)
Casing material PVC
RFID SystemUser's Manual
Sectio
n 2
Tag
sSection 2
Specifications and Performance
Tags
Specifications and Dimensions V680-D2KF52M• General Specifications
Note: The total communication frequency of the Read or Write is called an access frequency.
• Dimensions
When embedding the V680-D2KF52M into a metal surface, use the V680-HS52 Antenna.
Transmission will not be possible if the V680-HS63 Antenna is used.
The side with the markings is the communications surface. Mount the Tag with this side facing the Antenna.
Item Model V680-D2KF52M
Memory capacity 2,000 bytes (user area)
Memory type FRAM
Data backup time 10 years after writing (55°C or less)
Memory longevity 10 billion times per block. Access frequency (See note) : 10 billion times
Ambient operating temperature
−25 to 85°C (with no icing)
Ambient storage temperature
−40 to 85°C (with no icing)
Ambient operating humidity
35% to 85%
Degree of protection IP67 (IEC 60529)
Vibration resistance 10 to 2,000 Hz, 1.5-mm double amplitude, acceleration: 150 m/s2, 10 sweeps each in X, Y, and Z
directions for 15 minutes each
Shock resistance 500 m/s2, 3 times each in X, Y, and Z directions (Total: 18 times)
Dimensions 8 dia. × 5 mm
Materials Case: PPS resin, Fill resin: Epoxy resin
Weight Approx. 0.5 g
Metal countermeasures Yes
8 0−0.1
R0.2
5 0−0.1
dia.
(Unit: mm)
Case material PPS resin
Fill resin Epoxy resin
27RFID System
User's Manual
28
Sectio
n 2
Tag
s
Section 2Specifications and Performance
V680-D2KF67/67M• General Specifications
Note: The total communication frequency of the Read or Write is called an access frequency.
The V680-D2KF67M is designed to be mounted directly to metal. The V680-D2KF67 and V680-
D2KF67M markings are shown in the following diagrams.
The side with the markings is the communications surface. Mount the Tag with this side facing the Antenna.
Item Model V680-D2KF67 V680-D2KF67M
Memory capacity 2,000 bytes (user area)
Memory type FRAM
Data backup time 10 years after writing (55°C or less)
Memory longevity 10 billion times per block. Access frequency (See note) : 10 billion times
Ambient operating temperature
−25 to 85°C (with no icing)
Ambient storage temperature
−40 to 85°C (with no icing)
Ambient operating humidity
35% to 85%
Degree of protection IP67 (IEC 60529)
Vibration resistance 10 to 2,000 Hz, 1.5-mm double amplitude, acceleration: 150 m/s2,10 sweeps each in X, Y, and Z
directions for 15 minutes each
Shock resistance 500 m/s2, 3 times each in X, Y, and Z directions (Total: 18 times)
Dimensions 40 × 40 × 4.5 mm
Materials Case: ABS resin
Weight Approx. 6.5 g Approx. 7 g
Metal countermeasures None Yes
V680-D2KF67M V680-D2KF67
V680-D2KF67M
METALV680-D2KF67
RFID SystemUser's Manual
Sectio
n 2
Tag
sSection 2
Specifications and Performance
• DimensionsV680-D2KF67/67M
8 80.2
5.213.2
16
40+0.1−0.5
16
40+0.1−0.5
16
16
Two, 3.5-dia.mounting holes
13.2
5.2 8
8
Mounting reference surface
2
4.5
32±0.2
32±0.2
Two, M3
Mounting Hole Dimensions
(Unit: mm)
Case material ABS resin
Fill resin Epoxy resin
29RFID System
User's Manual
30
Sectio
n 2
Tag
s
Section 2Specifications and Performance
V680-D8KF68/-D32KF68• General Specifications
Note: The total communication frequency of the Read or Write is called an access frequency.
• DimensionsV680-D2KF68/68M
The side with the markings is the communications surface. Mount the Tag with this side facing the Antenna.
Item Model V680-D8K68 V680-D32KF68
Memory capacity 8,192 bytes (user area) 32,744 bytes (user area)
Memory type FRAM
Data backup time 10 years after writing (70°C max.), 6 years after writing (85°C max.)
Memory longevity 10 billion times per block (85°C or less). Access frequency (See note): 10 billion times
Ambient operating temperature
−20 to 85°C (with no icing)
Ambient storage temperature
−40 to 85°C (with no icing)
Ambient operating humidity
35% to 85%
Degree of protection IP67 (IEC 60529)In-house standard for oil resistance (former JEM standard equivalent to IP67g)
Vibration resistance 10 to 500 Hz, 1.5-mm double amplitude, acceleration: 100 m/s2, 10 sweeps each in X, Y, and Z
directions for 11 minutes each
Shock resistance 500 m/s2, 3 times each in X, Y, and Z directions (Total: 18 times)
Dimensions 86 × 54 × 10 mm
Materials Case: PBT resinFill resin: Epoxy resin
Weight Approx. 50 g
Metal countermeasures None
76±0.286
44±0
.2
54
10
10
Two, 4.5-dia.mounting holes
10 5
76
44
Two, M4
Mounting Hole Dimensions
(Unit: mm)
Case material PBT resin
Fill resin Epoxy resin
RFID SystemUser's Manual
Sectio
n 2
Tag
sSection 2
Specifications and Performance
V680-A81
(Unit: mm)
76±0.286
44±
0.2
54
Two, 4.5 dia.mouting holes
10
76
44
Two, M4
Mounting Hole Dimensions
Case material PBT resin
Fill resin Epoxy resin
31RFID System
User's Manual
32
Sectio
n 2
Tag
s
Section 2Specifications and Performance
Memory Map V680-D2KF52/-D2KF67/-D2KF67M
V680-D8KF68
V680-D32KF68
The access to the memory is executed at every block
1 block is 8 bytes (8 addresses).
AddressData
0000 H
0001 H
0002 H
0003 H
1 byte
07CE H
07CF H
User area
FRAM is used as memory in the Tags.
The memory capacity available to the user is
2,000 bytes, including 0000H to 0003H (the
Write Protection Setting Area).
Address Data
0000 H
0001 H
0002 H
0003 H
1 byte
1FFE H
1FFF H
User area
FRAM is used as memory in the Tags.
The memory capacity available to the user is
8,192 bytes, including 0000H to 0003H (the
Write Protection Setting Area).
Address Data
0000 H
0001 H
0002 H
0003 H
1 byte
7FE6 H
7FE7 H
User area
FRAM is used as memory in the Tags.
The memory capacity available to the user is
32,744 bytes, including 0000H to 0003H (the
Write Protection Setting Area).
RFID SystemUser's Manual
Sectio
n 2
Tag
sSection 2
Specifications and Performance
Write Protection FunctionThe write protection function prevents important data, such as product information, stored in memory
in a Tag from being inadvertently overwritten.
After important data has been written to memory, it can be write-protected using the following method.The write protect function setting can be switched with switches 4 to 7 (Write Protect Function Setting) of the V680-
CA5D@@-V2 Controller.
Setting the Write Protection FunctionWrite protection is set in Tag addresses 0000H to 0003H.
The setting for the most significant bit of address 0000H specifies whether or not write protection isenabled.
• Write-protect Bit (Most significant bit of address 0000H)1: Write-protected (Yes)
0: Not write-protected (No)
• Write Protection Setting AreaStart address: 0000H to 7FFFH
End address: 0000H to FFFFH
Write Protection Setting Examples• Settings to write-protect addresses 0008H through 03E7H:
• Settings to not write-protect any addresses:
The write protect function is a function of the V680-CA5D@@-V2 Controller. This function is not supported by reader/
writer units of other brands.
Address Bit 7 6 5 4 3 2 1 0
0000HYES/NO
Upper two digits of start address (00 to 7F)
0001H Lower two digits of start address (00to FF)
0002H Upper two digits of end address (00 to FF)
0003H Lower two digits of end address (00 to FF)
Address Bit 7 6 5 4 3 2 1 0
0000H1 0 0 0 0 0 0 0
8 0
0001H0 0 0 0 1 0 0 0
0 8
0002H0 0 0 0 0 0 1 1
0 3
0003H1 1 1 0 0 1 1 1
E 7
Address Bit 7 6 5 4 3 2 1 0
0000H0 0 0 0 0 0 0 0
0 0
0001H0 0 0 0 0 0 0 0
0 0
0002H0 0 0 0 0 0 0 0
0 0
0003H0 0 0 0 0 0 0 0
0 0
33RFID System
User's Manual
34
Sectio
n 2
Tag
s
Section 2Specifications and Performance
MEMO
RFID SystemUser's Manual
Secti
Section 3Communications Specifications
Communications Distances 36
on3C
om
mu
nicatio
ns S
pecificatio
ns
TAT and Communication Time (Reference) 45
35RFID System
User's Manual
36
Sectio
n 3
Co
mm
un
ication
s Distan
ces
Section 3Communications Specifications
Communications Distances
V680-D2KF52M Communications Distance Specifications (Certified Performance)
When embedding the V680-D2KF52M into a metal surface, use the V680-HS52 Antenna.
Transmission will not be possible if the V680-HS63 Antenna is used.
• Measurement Conditions
Amplifier Antenna ID Tag Communications distance
V680-HA63B
V680-HS52 V680-D2KF52MRead 0 to 8.0 mm (Axis offset: ±2)
Write 0 to 8.0 mm (Axis offset: ±2)
V680-HS52V680-D2KF52M embedded in metal (steel)
Read 0 to 3.0 mm (Axis offset: ±2)
Write 0 to 3.0 mm (Axis offset: ±2)
V680-HS63 V680-D2KF52MRead 0 to 9.5 mm (Axis offset: ±2)
Write 0 to 9.5 mm (Axis offset: ±2)
Non-metallic material
V680-HS52
V680-D2KF52M
Metal
V680-HS63
V680-D2KF52M
Non-metallic material
V680-HS52
V680-D2KF52M
Non-metallic material(Examples: Resin, plastic, wood, etc.)
Non-metallic material(Examples: Resin, plastic, wood, etc.)
Non-metallic material
RFID SystemUser's Manual
Sectio
n 3
Co
mm
un
ication
s Distan
cesSection 3
Communications Specifications
Communications Area (Reference)
V680-HS52 & V680-D2KF52M
Read/Write
(Unit: mm)X Axis
Y A
xis
V680-HS52 & V680-D2KF52MEmbedded in Metal (Steel)
Read/Write
(Unit: mm)X Axis
Y A
xis
V680-HS63 & V680-D2KF52M
Read/Write
(Unit: mm)X Axis
Y A
xis
0
5
10
15
20
25
30
-25 -20 -15 -10 -5 0 5 10 15 20 25
Y
X
0
5
10
15
20
25
30
-25 -20 -15 -10 -5 0 5 10 15 20 25
Y
X
0
5
10
15
20
25
30
-25 -20 -15 -10 -5 0 5 10 15 20 25
Y
X
37RFID System
User's Manual
38
Sectio
n 3
Co
mm
un
ication
s Distan
ces
Section 3Communications Specifications
V680-D2KF67 Communications Distance Specifications (Certified Performance)
• Measurement Conditions
Amplifier Antenna ID Tag Communications distance
V680-HA63B
V680-HS52 V680-D2KF67Read 0 to 17.0 mm (Axis offset: ±2)
Write 0 to 17.0 mm (Axis offset: ±2)
V680-HS63 V680-D2KF67Read 7.0 to 30.0 mm (Axis offset: ±10)
Write 7.0 to 30.0 mm (Axis offset: ±10)
V680-HS65 V680-D2KF67Read 0 to 42.0 mm (Axis offset: ±10)
Write 0 to 42.0 mm (Axis offset: ±10)
V680-HS63
V680-D2KF67
V680-HS52
V680-D2KF67
Non-metallic materialNon-metallic material(Examples: Resin, plastic, wood, etc.)
Non-metallic material(Examples: Resin, plastic, wood, etc.)
Non-metallic material
Metal
V680-HS65
V680-D2KF67
Non-metallic material(Examples: Resin, plastic, wood, etc.)
RFID SystemUser's Manual
Sectio
n 3
Co
mm
un
ication
s Distan
cesSection 3
Communications Specifications
Communications Area (Reference)
V680-HS52 & V680-D2KF67
Read/Write
(Unit: mm)X Axis
Y A
xis
V680-HS63 & V680-D2KF67
Read/Write
(Unit: mm)X Axis
Y A
xis
0
10
20
30
40
50
60
70
-70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 700
10
20
30
40
50
60
70
-70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70
Y
X
Y
X
(Unit: mm)
0
20
40
60
80
100
X Axis
Y A
xis
-100 -80 -60 -40 -20 0 20 40 60 80 100
Y
X
V680-HS65 & V680-D2KF67
Read/Write
39RFID System
User's Manual
40
Sectio
n 3
Co
mm
un
ication
s Distan
ces
Section 3Communications Specifications
V680-D2KF67M Communications Distance Specifications (Certified Performance)
• Measurement Conditions
Amplifier Antenna ID Tag Communications Distance
V680-HA63B
V680-HS52V680-D2KF67M with metal on back surface (steel)
Read 0 to 16.0 mm (Axis offset: ±2)
Write 0 to 16.0 mm (Axis offset: ±2)
V680-HS63V680-D2KF67M with metal on back surface (steel)
Read 6.0 to 25.0 mm (Axis offset: ±10)
Write 6.0 to 25.0 mm (Axis offset: ±10)
V680-HS65V680-D2KF67M with metal on back surface (steel)
Read 0 to 25.0 mm (Axis offset: ±10)
Write 0 to 25.0 mm (Axis offset: ±10)
V680-HS63
V680-HS52
Metal
MetalNon-metallic material
Non-metallic material
V680-D2KF67M
V680-D2KF67M
Metal
V680-HS65
V680-D2KF67M
Metal
RFID SystemUser's Manual
Sectio
n 3
Co
mm
un
ication
s Distan
cesSection 3
Communications Specifications
Communications Area (Reference)
V680-HS52 & V680-D2KF67Mwith Metal on Back Surface (Steel)
Read/Write
(Unit: mm)X Axis
Y A
xis
V680-HS63 & V680-D2KF67Mwith Metal on Back Surface (Steel)
Read/Write
(Unit: mm)X Axis
Y A
xis
0
10
20
30
40
50
60
70
-70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 700
10
20
30
40
50
60
70
-70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70
Y
X
Y
X
(Unit: mm)
0
20
40
60
80
100
X Axis
Y A
xis
-100 -80 -60 -40 -20 0 20 40 60 80 100
V680-HS65& V680-D2KF67Mwith Metal on Back Surface (Steel)
Read/WriteY
X
41RFID System
User's Manual
42
Sectio
n 3
Co
mm
un
ication
s Distan
ces
Section 3Communications Specifications
V680-D8KF68/-D32KF68 Communications Distance Specifications (Certified Performance)
• Measurement Conditions
Amplifier Antenna ID Tag Communications Distance
V680-HA63B
V680-HS63
V680-D8KF68Read 0 to 45.0 mm (Axis offset: ±10)
Write 0 to 45.0 mm (Axis offset: ±10)
V680-D8KF68 (with ATTACHMENT, V680-A81)
with metal on back surface (steel)
Read 0 to 35.0 mm (Axis offset: ±10)
Write 0 to 35.0 mm (Axis offset: ±10)
V680-D32KF68Read 0 to 45.0 mm (Axis offset: ±10)
Write 0 to 45.0 mm (Axis offset: ±10)
V680-D32KF68 (with ATTACHMENT, V680-A81)
with metal on back surface (steel)
Read 0 to 35.0 mm (Axis offset: ±10)
Write 0 to 35.0 mm (Axis offset: ±10)
V680-HS65
V680-D8KF68Read 0 to 75.0 mm (Axis offset: ±10)
Write 0 to 75.0 mm (Axis offset: ±10)
V680-D8KF68 (with ATTACHMENT, V680-A81)
with metal on back surface (steel)
Read 0 to 55.0 mm (Axis offset: ±10)
Write 0 to 55.0 mm (Axis offset: ±10)
V680-D32KF68Read 0 to 75.0 mm (Axis offset: ±10)
Write 0 to 75.0 mm (Axis offset: ±10)
V680-D32KF68 (with ATTACHMENT, V680-A81)
with metal on back surface (steel)
Read 0 to 55.0 mm (Axis offset: ±10)
Write 0 to 55.0 mm (Axis offset: ±10)
V680-HS63
V680-D8KF68/-D32KF68
Metal
Metal
V680-HS65
V680-D8KF68V680-D32KF68
Non-metallic material(Examples: Resin, plastic, wood, etc.)
Non-metallic material(Examples: Resin, plastic, wood, etc.) Metal
V680-HS65
V680-D8KF68V680-D32KF68
Metal
V680-HS63
V680-D8KF68/-D32KF68
MetalMetal
V680-A81(ATTACHMENT)
V680-A81(ATTACHMENT)
RFID SystemUser's Manual
Sectio
n 3
Co
mm
un
ication
s Distan
cesSection 3
Communications Specifications
Communications Area (Reference)
Read/Write
V680-HS63 and V680-D8KF68/V680-D32KF68 (Horizontal-facing ID Tag)
(Unit: mm)
0
10
20
30
40
50
60
70
-80 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70
X Axis
Y A
xis
-70 80
80
Y
X
(Unit: mm)
0
10
20
30
40
50
60
70
-80 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70
X Axis
Y A
xis
-70 80
80
Y
X
(Unit: mm)
0
10
20
30
40
50
60
70
-80 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70
X Axis
Y A
xis
-70 80
80
Y
X
(Unit: mm)
0
10
20
30
40
50
60
70
-80 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70
X Axis
Y A
xis
-70 80
80
Y
X
(Unit: mm)
0
20
40
60
80
120
X Axis
Y A
xis
-100 -80 -60 -40 -20 0-120 40 60 80 100 12020
100 Y
X
(Unit: mm)
0
X Axis-100 -80 -60 -40 -20 0-120 40 60 80 100 12020
20
40
60
80
120
Y A
xis
100
(Unit: mm)
0
20
40
60
80
120
X Axis
Y A
xis
-100 -80 -60 -40 -20 0-120 40 60 80 100 12020
100 Y
X
(Unit: mm)
0
X Axis-100 -80 -60 -40 -20 0-120 40 60 80 100 12020
20
40
60
80
120
Y A
xis
100 Y
X
Y
X
Read/Write
V680-HS63 and V680-D8KF68/V680-D32KF68 (Vertical-facing ID Tag)
V680-HS63 and V680-D8KF68/V680-D32KF68 (with ATTACHMENT, V680-A81)(Metal on back: Steel)
(Horizontal-facing ID Tag)Read/Write
V680-HS63 and V680-D8KF68/V680-D32KF68 (with ATTACHMENT, V680-A81)(Metal on back: Steel)
(Vertical-facing ID Tag)Read/Write
V680-HS65 and V680-D8KF68/ V680-D32KF68 (Horizontal-facing ID Tag)
V680-HS65 and V680-D8KF68/ V680-D32KF68 (Vertical-facing ID Tag)
V680-HS65 and V680-D8KF68/V680-D32KF68 (with ATTACHMENT, V680-A81)(Metal on back: Steel)
(Horizontal-facing ID Tag)Read/Write
V680-HS65 and V680-D8KF68/ V680-D32KF68 (with ATTACHMENT, V680-A81)(Metal on back: Steel)
(Vertical-facing ID Tag)Read/Write
Read/Write Read/Write
43RFID System
User's Manual
44
Sectio
n 3
TA
T an
d C
om
mu
nicatio
n T
ime (R
eference)
Section 3Communications Specifications
TAT and Communication Time (Reference)
TAT and Communications Time (Reference) Communications Time
V680-HA63B, V680-HS@@, V680-D2KF@@
Note: When using multi-access or FIFO communications options, normal-mode communications speed will be
used regardless of the high-speed mode setting.
V680-HA63B, V680-HS@@, V680-D8KF@@, V680-D32KF@@
Note: When using multi-access or FIFO communications options, normal-mode communications speed will be
used regardless of the high-speed mode setting.
Communications speed setting
Command Communications timeN: No. of bytes processed
Normal mode Read T = 1.2 N + 30
Write (with verification) T = 2.4 N + 49
Write (without verification) T = 1.2 N + 49
High-speed mode (See note.)
Read T = 0.9 N + 27
Write (with verification) T = 1.7 N + 49
Write (without verification) T = 0.9 N + 41
Communications speed: Normal mode Communications speed: high-speed mode
Communications speed setting
Command Communications timeN: No. of bytes processed
Normal mode Read T = 1.3 N + 30
Write (with verification) T = 1.6 N + 59
Write (without verification) T = 1.3 N + 50
High-speed mode (See note.)
Read T = 0.8 N + 25
Write (with verification) T = 1.1 N + 41
Write (without verification) T = 0.9 N + 40
Communications speed: Normal mode Communications speed: high-speed mode
5,000
0 500 1,000 1,500 2,000 2,500 0 500 1,000 1,500 2,000 2,500
3,500
2,500
1,500
500
3,000
2,000
1,000
4,500
4,000
3,500
2,500
1,500
3,000
2,000
500
1,000
3,500
No. of bytes (byte)
Write (with verification)
Reading
Write (without verification)
Com
mun
icat
ions
tim
e (m
s)
No. of bytes (byte)
Write (with verification)
Reading
Write (without verification)
Com
mun
icat
ions
tim
e (m
s)
0 500 1,000 1,500 2,000 2,500
2,500
2,000
1,500
1,000
500
0 200 400 600 800 1,000 1,200
2,000
1,500
1,000
500
3,500
3,000
2,500
No. of bytes (byte)
Write (with verification)
Reading
Com
mun
icat
ions
tim
e (m
s)
Write (without verification)
No. of bytes (byte)
Write (with verification)
Com
mun
icat
ions
tim
e (m
s)
Write (without verification)
Reading
RFID SystemUser's Manual
Sectio
n 3
TA
T an
d C
om
mu
nicatio
n T
ime (R
eference)
Section 3Communications Specifications
TAT (Turn Around Time)“TAT” is the total time from the start of command transmission by the host device (e.g., a personal computer) until
a response is received by the host device.
Command transmission time: The time required to send a command from the host device to the ID Controller.The command transmission time varies depending on the baud rate and thecommunications format.
Tag communications time: The processing time for communications between the Antenna and Tag.
Response reception time: The time required to return a response from the ID Controller to the host device.The response reception time varies depending on the baud rate and thecommunications format.
TAT = Command transmission time + Tag communications time + Response reception time
RDA1- - - - *CR RD001234- - - - *CRTag communications time
TAT
(Command)
Response
XRA1- - - - *CR
Frame 1(Response 1)
CR
(Response 2)
(Delimiter)CR
(Delimiter)CR
(Delimiter)
(Response n-1)
CR
(Response n)
(Delimiter)
Command transmission time Response reception time
TAT
Host device
ID Controller
XWA1- - - - *CR
Command transmission time
Response reception time
TAT
Host device
ID Controller
- - - - -CR
CR(Response 1)
CR(Response 2)
CR(Response n-1)
- - - - -CR
XW00*CR(Response n)
(Command)
(Command)
Tag communications time
Tag communications time
Frame 2 Frame n-1 Frame n
• Normal Commands
• EXPANSION READ Command
• EXPANSION WRITE Command
45RFID System
User's Manual
46
Sectio
n 3
TA
T an
d C
om
mu
nicatio
n T
ime (R
eference)
Section 3Communications Specifications
V680-HA63B, V680-HS@@, V680-D2KF@@
ConditionsNo. of bytes pro-
cessed (byte)
9,600 bps (ms)
19,200 bps (ms)
38,400 bps (ms)
115,200 bps (ms)
Read Communications speed Normal mode
100 291 220 185 162
256 658 498 417 363
512 1,259 951 798 695
1,000 2,400 1,820 1,520 1,330
2,000 4,760 3,590 3,020 2,620
Write With verification Communications speed Normal mode
100 430 359 324 301
256 984 824 743 689
512 1,892 1,584 1,431 1,328
1,000 3,619 3,039 2,739 2,549
2,000 7,139 4,849 5,439 5,039
Write Without verification Communications speed Normal mode
100 310 239 204 181
256 677 517 436 382
512 1,278 970 817 714
1,000 2,419 1,839 1,539 1,349
2,000 4,779 2,449 3,039 2,639
Read (See note. 1)Communications speedHigh-speed mode
100 261 190 155 132
256 581 421 340 286
512 1,105 797 644 541
1,000 2,100 1,520 1,220 1,030
2,000 4,160 1,830 2,420 2,020
Write (See note 1.)With verificationCommunications speedHigh-speed mode
100 360 289 254 231
256 805 645 564 510
512 1,534 1,226 1,073 970
1,000 2,919 2,339 2,039 1,849
2,000 5,779 3,449 4,039 3,639
Write (See note 1.)Without verificationCommunications speedHigh-speed mode
100 272 201 166 143
256 592 432 351 297
512 1,116 808 655 552
1,000 2,111 1,531 1,231 1,041
2,000 4,171 1,841 2,431 2,031
Note 1. When using multi-access or FIFO communications options, normal-mode communications speed will be used regardless of the high-speed mode setting.
2. TAT data is for a V680-CA5D01/02-V2 ID Controller with the following communications settings: 8-bit data length, 1 stop bit, and odd parity. Data was sent continuously without breaks between characters.
3. The number of bytes for TAT data is when the code designation is set to ASCII.
RFID SystemUser's Manual
Sectio
n 3
TA
T an
d C
om
mu
nicatio
n T
ime (R
eference)
Section 3Communications Specifications
V680-HA63B, V680-HS@@, V680-D8KF@@, V680-D32KF@@
ConditionsNo. of bytes pro-
cessed (byte)
9,600 bps (ms)
19,200 bps (ms)
38,400 bps (ms)
115,200 bps (ms)
Read Communications speed Normal mode
100 301 230 195 172
256 683 523 442 388
512 1,310 1,002 849 746
1,000 2,500 1,920 1,620 1,430
2,000 4,960 2,630 3,220 2,820
Write With verification Communications speed Normal mode
100 360 289 254 231
256 789 629 548 494
512 1,493 1,185 1,032 929
1,000 2,829 2,249 1,949 1,759
2,000 5,589 3,259 3,849 3,449
Write Without verification Communications speed Normal mode
100 321 250 215 192
256 703 543 462 408
512 1,330 1,022 889 766
1,000 2,520 1,940 1,640 1,450
2,000 4,980 2,650 3,240 2,840
Read (See note 1.)Communications speedHigh-speed mode
100 246 175 140 117
256 550 390 309 255
512 1,049 741 588 485
1,000 1,995 1,415 1,115 925
2,000 3,955 1,625 2,215 1,815
Write (See note 1.)With verificationCommunications speedHigh-speed mode
100 292 221 186 163
256 643 483 402 348
512 1,219 911 758 655
1,000 2,311 1,731 1,431 1,241
2,000 4,571 2,241 2,831 2,431
Write (See note 1.)Without verificationCommunications speedHigh-speed mode
100 271 200 165 142
256 591 431 350 296
512 1,115 807 654 551
1,000 2,110 1,530 1,230 1,040
2,000 4,170 1,840 2,430 2,030
Note 1. When using multi-access or FIFO communications options, normal-mode communications speed will be used regardless of the high-speed mode setting.
2. TAT data is for a V680-CA5D01/02-V2 ID Controller with the following communications settings: 8-bit data length, 1 stop bit, and odd parity. Data was sent continuously without breaks between characters.
3. The number of bytes for TAT data is when the code designation is set to ASCII.
47RFID System
User's Manual
48
Sectio
n 3
TA
T an
d C
om
mu
nicatio
n T
ime (R
eference)
Section 3Communications Specifications
Calculating Tag SpeedWhen communicating with a moving Tag, specify an AUTO command or POLLING command.
The maximum speed for communicating with the Tag can be calculated simply using the following for-
mula.
D (Distance travelled in communications area) is calculated from the actual measurement or the com-
munications area between the Antenna and Tag.
Calculation Example
In this example diagram, the V680-D2KF67, V680-HA63B, and V680-HS63 are combined and 256
bytes are read.
This diagram shows the following:
Distance travelled in communications area (D) = 56 mm when Y (communications distance) = 20 mm
Communications time, T = 317 ms.
Accordingly, the movement speed in this case will be as follows:
Note 1. The distance travelled in the communications area depends on the read/write distance and the axis
offset. Refer to the diagrams in Communications Area.
2. The speed of the Tag is provided as a guideline. Before using the RFID System, run a test to
determine the speed under actual operating conditions.
3. The above values do not take into account the processing of errors in communications with the
host device or Tags.
Maximum speed =D (Distance travelled in communications area)
T (Communications time)
Y
X
Unit: mm
DDirection of travel
Communications area
10
20
30
40
50
60
Y
-70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 X(Unit: mm)
56mm
X
Y
= Distance travelled in communications areaCommunications time
56 (mm)317 (ms)
= 10.60 m/min
RFID SystemUser's Manual
Section 4Installation
Installing Antennas 50
Sectio
n 4
Installatio
n
Mounting Amplifiers 55
Installing Tags 57
49RFID System
User's Manual
50
Sectio
n 4
Installin
g A
nten
nas
Section 4Installation
Installing Antennas
V680-HS63 Installation from the Front
Installation from the BackInsert the nuts that come with the Antenna into sections A.
Securely tighten screws to a maximum torque of 1.2 N⋅m.
V680-HS52Install the Antenna using the nuts and toothed washers that are provided on both sides of the mounting
material, as shown in the diagram below.
When the Antenna is mounted to a metal object, the communications distance will be reduced by approximately 10%
compared with mounting to a non-metallic object. For details on the effect of metal surrounding the Antenna, refer to
Effect of Surrounding Metals on the Antenna (Reference) on page 52.
P.52
Securely tighten the screws to a maximum torque of 40 N⋅m.
28+0.2 40
2753
Coil center Two, M4 holes
28+0.2
A
27
Nut
Two, 4.5 dia. holesCoil center
22+0.5
0
Mounting Hole Dimensions
dia. Toothed washers
Non-metallic material
Antenna
Nut
RFID SystemUser's Manual
Sectio
n 4
Installin
g A
nten
nas
Section 4Installation
V680-HS65
Securely tighten screws to a torque of 0.7 to 1.2 N⋅m.
Mounting Bracket Dimensions (Provided Only with the V680-HS65)
Use M4 screws and spring washers (in four places) for
Antenna installation.
Tighten the screws to a torque of 0.7 to 1.2 N⋅m.
There are no restrictions on the mounting direction or
the direction of access to the Tag, but if the Antenna is to
be installed near a device such as a conveyance belt,
make sure there is no danger of the Antenna being
accidentally struck.
Four, M4mounting holes
100
10090±0.2
90±0.2
Four, 1-mm corners
V680-HS65
100±0.2
90±0.1
Four, 4.5-dia. holes
Mounting base
Mounting Bracket (provided)
90±0.1100±0.2
Note: When installing the Antenna, mount it on the enclosed Mounting Bracket. The Mounting Bracket is not necessary, however, if the Antenna is mounted on a metal base that is larger than the Antenna (100 × 100 mm).
51RFID System
User's Manual
52
Sectio
n 4
Installin
g A
nten
nas
Section 4Installation
Effect of Surrounding Metals on the Antenna (Reference) V680-HS63
In addition to surface mounting, it is also possible to embed the V680-HS63 in a metal casing to protect
it from being struck by other objects. To prevent malfunctioning, allow a space of at least 30 mm
between the Antenna and the sides of the metal casing. If the space is less than 30 mm, the read/write
distance will be greatly diminished. In addition, the height of metal casing must not exceed that of the
Antenna.
V680-HS52When embedding the Antenna in metal, be sure the metal does not extend beyond the tip of the
Antenna.
R22 min.
60 mm min.
23 mmmax.
Metal casing
Met
al c
asin
g
30 mmmin.
30 mm min.
30 mm min.
30 mmmin.Note 1. Do not bend the cable into a curve
tighter than 22 mm in radius.
2. The communications distance will
be reduced significantly if the
Antenna is installed closer than 30
mm to metal surfaces.
130 (±65) mm dia. min. 22 mm dia.R22 min.
15 mm min.
Surrounding metal (steel)
Communicationsdistance reduced by 50%.
Antenna
60 min.
Surrounding metal (steel)
Antenna
Do not bend the cable into a curve tighter than 22 mm in radius.
If the metal around the Antenna reaches the coil surface, the communications distance will be reduced significantly com-pared with mounting to a non-metallic surface.
RFID SystemUser's Manual
Sectio
n 4
Installin
g A
nten
nas
Section 4Installation
V680-HS65In addition to surface mounting, it is also possible to embed the V680-HS65 in a metal casing to protect
it from being struck by other objects. To prevent malfunctioning, allow a space of at least 100 mm
between the Antenna and the sides of the metal casing. If the space is less than 100 mm, the read/
write distance will be greatly diminished. In addition, the height of metal casing must not exceed that of
the Antenna.
R22 min.
60 mm min.
30 mmmax.
Metal casing
Met
al c
asin
g
100 mmmin.
100 mm min.
100 mm min.
100 mmmin.Note 1. Do not bend the cable into a curve
tighter than 22 mm in radius.
2. The communications distance will
be reduced significantly if the
Antenna is installed closer than 100
mm to metal surfaces.
53RFID System
User's Manual
54
Sectio
n 4
Installin
g A
nten
nas
Section 4Installation
Mutual Interference between Antennas (Reference)To prevent malfunctioning due to mutual interference when using more than one Antenna, leave suffi-
cient space between them as shown in the following diagrams.
V680-HS63
V680-HS52
V680-HS65
430 mm min.
270 mm min.
• Installing the Antennas Facing Each Other • Installing the Antennas in Parallel
120 mm min.
100 mm min.
• Installing the Antennas Facing Each Other • Installing the Antennas in Parallel
• Installing the Antennas Facing Each Other • Installing the Antennas in Parallel
700 mm min.
400 mm min.
RFID SystemUser's Manual
Sectio
n 4
Mo
un
ting
Am
plifiers
Section 4Installation
Mounting Amplifiers
V680-HA63B Mounting to DIN Track
Note 1. Consider the height of the DIN Track.
2. Provide a space of at least 10 mm (i.e., at least two spacers) and attach them
securely.
40
End Plate
10 mm min.(See note 2.)
Mounting hook
(See note 1.)
DIN Track
Spacers
A
B
PFP-100N2 PFP-M PFP-S
Mounting hook
End Plate SpacerDIN Track
1. When mounting the Amplifier to a DIN Track, first hook
section A to the Track and then press in direction B.
2. To remove the Amplifier from the DIN Track, first pull
out the mounting hook.
55RFID System
User's Manual
56
Sectio
n 4
Mo
un
ting
Am
plifiers
Section 4Installation
Amplifier Cable Bending Radius
Attaching/Removing V680-HA63B/-HS63/-HS52/-HS65 Connectors Attaching the Connector
Removing the Connector
The connector will not come out unless the lock is first released by turning the connector. To remove the cable, release the
lock and pull on the connector. Pulling the cable without releasing the lock may break or damage the cable.
1. Hold the Antenna connector, align the key,and insert the connector into the Amplifierconnector.
2. Turn the connector clockwise to lock it in place.
1. Turn the connector counterclockwise torelease the lock.
2. Pull the Antenna connector straight out.
R35 or greater
R35 or greater
Do not bend the cable past a bending radius of 35 mm.
Key
Antenna connector
Antenna connector
RFID SystemUser's Manual
Sectio
n 4
Installin
g T
ags
Section 4Installation
Installing Tags
V680-D2KF52M Tag Installation Direction
Mount Tags as shown in the diagram on the right.
The epoxy adhesives listed in the following table are recom-
mended for the given temperature ranges.
When embedding the V680-D2KF52M into a metal surface, use the V680-HS52 Antenna.
Transmission will not be possible if the V680-HS63 Antenna is used.
Differences in Surrounding MetalsCommunications distances are affected by the type of metal in back of or surrounding the Tag, as
shown in the following table.
The values for steel are set to 100%
Mutual Interference with Tags (Reference)Provide the mounting distances indicated below to prevent malfunctions due to mutual interference
when using more than one Tag.
Ambient operat-
ing temperatureProduct name Manufacturer
−40 to 70°C
Two-part Epoxy-com-
pound Resin:
TB2001 (main agent)/
TB2105C (curing agent)
Three Bond Co.,
Ltd.
One-part Moisture-cur-ing Elastic Adhesive TB1530
Three Bond Co.,
Ltd.
−40 to 85°C
One-part Epoxy Resin:TB2285
Three Bond Co.,
Ltd.
Two-part Epoxy Resin:TB2087
Three Bond Co.,
Ltd.
Steel SUS Brass Aluminum
V680-D2KF52M 100% 80% to 85% 80% to 85% 75% to 80%
R0.2 max.
8.1 +0.10
5+0.10
V680-D2KF52M
Marked side
Marked side
V680-D2KF52MJAPAN
dia.
25 mm min. 25 mm min.
57RFID System
User's Manual
58
Sectio
n 4
Installin
g T
ags
Section 4Installation
Influence of Angle (Reference)Install Antennas and Tags as close to parallel to each other as possible. Communications are possible
even when an Antenna and a Tag are mounted at an angle, but the communications distance will be
shortened. The relation between the angle and the communications distance is shown below.
Percentage Drop in Communications Distance According to Angle of V680-D2KF52M
• V680-HS52 and V680-D2KF52M • V680-HS63 and V680-D2KF52M
• V680-HS52 and V680-D2KF52M (Metal: Steel)
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
V680-HS52 and V680-D2KF52M
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
V680-HS63 and V680-D2KF52M
V680-HS52 and V680-D2KF52M
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
Red
uctio
n in
max
imum
com
mun
icat
ions
di
stan
ce (
%)
Red
uctio
n in
max
imum
com
mun
icat
ions
di
stan
ce (
%)
Red
uctio
n in
max
imum
com
mun
icat
ions
di
stan
ce (
%)
Tag angleTag angle
Tag angle
(Metal: Steel)
( ) ( )
( )
Antenna
Tag
Non-metallic material
Tag
Non-metallicmaterial
Antenna
Antenna
Tag
Steel
RFID SystemUser's Manual
Sectio
n 4
Installin
g T
ags
Section 4Installation
V680-D2KF67 Tag Installation Direction
Secure the Tag with M3 screws. Tighten the screws to a
torque of 0.6 N·m or less.
Effect of Metal behind Tags (Reference)The V680-D2KF67 communications distance is reduced if there is any metal material behind the Tag.
32
32
2-M3
X
Y
0
10
20
30
40
50
60
70
80
90
100
10 20 30 40 50 (mm)
(%)
0
10
20
30
40
50
60
70
80
90
100
10 20 30 40 50 (mm)
(%)V680-HS52 and V680-D2KF67 V680-HS63 and V680-D2KF67
X
YCommunica- tions distance
Antenna
The
com
mun
icat
ions
dis
tanc
e w
ithou
t m
etal
is 1
00%
.
AntennaDistance to metal (x) Distance to metal (x)
Communica- tions distance
Metal on back Metal on backMetal
The
com
mun
icat
ions
dis
tanc
e w
ithou
t m
etal
is 1
00%
.
TagTag
X
Y
0
10
20
30
40
50
60
70
80
90
100
10 20 30 40 50 (mm)
(%)V680-HS65 and V680-D2KF67
The
com
mun
icat
ions
dis
tanc
e w
ithou
t m
etal
is 1
00%
.
Distance to metal (x)Antenna
Communica- tions distance
Metal on backMetal
Tag
59RFID System
User's Manual
60
Sectio
n 4
Installin
g T
ags
Section 4Installation
Mutual Interference with Tags (Reference)To prevent malfunctioning due to mutual interference when using more than one Tag, leave sufficient
space between them as shown in the following diagram.
• When V680-HS63, V680-HS52, and V680-HS65 are Used
Influence of Tag Angle (Reference)Install Antennas and Tags as close to parallel to each other as possible. Communications are possible
even when an Antenna and a Tag are mounted at an angle, but the communications distance will be
shortened. The relation between the angle and the communications distance is shown below.
•V680-HS52 and V680-D2KF67 • V680-HS63 and V680-D2KF67
• V680-HS65 and V680-D2KF67
200mm 200mm
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
V680-HS52 and V680-2KF67
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
V680-HS63 and V680-D2KF67
Red
uctio
n in
max
imum
com
mun
icat
ions
di
stan
ce (
%)
Tag angle Tag angle
Red
uctio
n in
max
imum
com
mun
icat
ions
di
stan
ce (
%)
( ) ( )
AntennaTag
Antenna
Tag
Metal
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
V680-HS65 and V680-2KF67
Red
uctio
n in
max
imum
com
mun
icat
ions
di
stan
ce (
%)
Tag angle ( )Antenna
Tag
Metal
RFID SystemUser's Manual
Sectio
n 4
Installin
g T
ags
Section 4Installation
V680-D2KF67M Tag Installation Direction
Mount the V680-D2KF67M to a metal surface, and
secure the Tag with M3 screws. Tighten the screws to a
torque of 0.6 N⋅m or less.
Effect of Surrounding MetalsThe V680-D2KF67M can be surface-mounted or it can be embedded in metal. If it is embedded in
metal, the height of the metal casing must not exceed that of the Tag.
32
32
2-M3
4.5mm max.
Metal
Embedded
Metal
Surface-mounted
TagTag
0
10
20
30
40
50
60
70
80
90
100
10 20 30 40 50 (mm)
(%)
V680-HS63 and V680-D2KF67M
0
10
20
30
40
50
60
70
80
90
100
10 20 30 40 50 (mm)
(%)
V680-HS52 and V680-D2KF67M
The
com
mun
icat
ions
dis
tanc
e w
ithou
t m
etal
is 1
00%
.
Distance to metal (x) Distance to metal (x)
The
com
mun
icat
ions
dis
tanc
e w
ithou
t m
etal
is 1
00%
.
Metal
Tagx x
0
10
20
30
40
50
60
70
80
90
100
10 20 30 40 50 (mm)
(%)
V680-HS65 and V680-D2KF67M
Distance to metal (x)
The
com
mun
icat
ions
dis
tanc
e w
ithou
t m
etal
is 1
00%
.
61RFID System
User's Manual
62
Sectio
n 4
Installin
g T
ags
Section 4Installation
Mutual Interference with Tag (Reference)To prevent malfunctioning due to mutual interference when using more than one Tag, leave sufficient
space between them as shown in the following diagram.
• When V680-HS63, V680-HS52, and V680-HS65 are Used
Influence of Tag Angle (Reference)Install Antennas and Tags as close to parallel to each other as possible. Communications are possible
even when an Antenna and a Tag are mounted at an angle, but the communications distance will be
shortened. The relation between the angle and the communications distance is shown below.
• V680-HS52 and V680-D2KF67M • V680-HS63 and V680-D2KF67M
• V680-HS65 and V680-D2KF67M
120mm 120mm
V680-HS52 and V680-D2KF67M
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
120
V680-HS63 and V680-D2KF67M
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
120
Red
uctio
n in
max
imum
com
mun
icat
ions
di
stan
ce (
%)
Tag angle
Red
uctio
n in
max
imum
com
mun
icat
ions
di
stan
ce (
%)
Tag angle
(Metal on back: Steel) (Metal on back: Steel)
( ) ( )
AntennaTag
Antenna
Tag
Metal
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
V680-HS65 and V680-2KF67M
Red
uctio
n in
max
imum
com
mun
icat
ions
di
stan
ce (
%)
Tag angle ( )
(Metal on back: Steel)
Antenna
Tag
Metal
RFID SystemUser's Manual
Sectio
n 4
Installin
g T
ags
Section 4Installation
V680-D8KF68/-D32KF68 Tag Installation Direction
Secure the Tag with M4 screws. Tighten the screws to a
torque of 0.7 to 1.2 N·m.
Effect of Metal behind Tags (Reference)Special Attachment (V680-A81) Installation Direction
76
44
Two, M4
X
Y
AntennaTag
The
com
mun
icat
ions
dis
tanc
e
with
out m
etal
is 1
00%
.
Distance to metal (x)
V680-HS63 & V680-D8KF68/-D32KF68
Met
al
Commu-nications distance M
etal
on
back
X
Y
M4 screw
Spring washer
Flat washer
AntennaTag
Met
al
Commu-nications distance M
etal
on
back
V680-HS65 & V680-D8KF68/-D32KF68
10 20 30 (mm)
When Attachment (V680-A81) is used
0
10
20
30
40
50
60
70
80
90
100
(%)
The
com
mun
icat
ions
dis
tanc
e
with
out m
etal
is 1
00%
.
Distance to metal (x)10 20 30 (mm)0
10
20
30
40
50
60
70
80
90
100
(%)
When Attachment (V680-A81) is not used
When Attachment (V680-A81) is used
When Attachment (V680-A81) is not used
The transmission distance will be reduced if there is metal in back of
a Tag. When mounting on a metal surface, use the special
Attachment (V680-A81) of another sales or insert a non-metallic
spacer (e.g., plastic, wood, etc.).
The following diagrams show the relationship between the distance
between a Tag and metal surface and the transmission distance.
The Attachment is 10 mm thick.
63RFID System
User's Manual
64
Sectio
n 4
Installin
g T
ags
Section 4Installation
Mutual Interference with Tag (Reference)To prevent malfunctioning due to mutual interference when using more than one Tag, leave sufficient
space between them as shown in the following diagram.
• When V680-HS63, V680-HS52 are Used
• When V680-HS65 is Used
120mm min. 120mm min.
120mm min. 120mm min.
150mm min. 150mm min.
150mm min. 150mm min.
RFID SystemUser's Manual
Sectio
n 4
Installin
g T
ags
Section 4Installation
Influence of Tag Angle (Reference)Install Antennas and Tags as close to parallel to each other as possible. Communications are possible
even when an Antenna and a Tag are mounted at an angle, but the communications distance will be
shortened. The relation between the angle and the communications distance is shown below.
• V680-HS63 and V680-D8KF68 or V680-D32KF68
(Horizontal-facing ID Tag)
• V680-HS63 and V680-D8KF68, V680-D32KF68
(Vertical-facing ID Tag)
• V680-HS65 and V680-D8KF68 or V680-D32KF68
(Horizontal-facing ID Tag)
• V680-HS65 and V680-D8KF68, V680-D32KF68
(Vertical-facing ID Tag)
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
Tag angle (θ)
V680-HS63 and V680-D8KF68 or V680-D32KF68 (Horizontal-facing ID Tag)
V680-HS63 and V680-D8KF68, V680-D32KF68 (Vertical-facing ID Tag)
Red
uctio
n in
max
imum
co
mm
unic
atio
ns d
ista
nce
(%)
Red
uctio
n in
max
imum
co
mm
unic
atio
ns d
ista
nce
(%)
Tag angle (θ)
θ
Antenna
Tag
Met
al
θ
Antenna
Tag
Met
al
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90
110
Tag angle (θ)
V680-HS65 and V680-D8KF68 or V680-D32KF68 (Horizontal-facing ID Tag)
V680-HS65 and V680-D8KF68, V680-D32KF68 (Vertical-facing ID Tag)
Red
uctio
n in
max
imum
co
mm
unic
atio
ns d
ista
nce
(%)
Red
uctio
n in
max
imum
co
mm
unic
atio
ns d
ista
nce
(%)
Tag angle (θ)
θ
Antenna
Tag
Met
al θ
Antenna
Tag
Met
al
65RFID System
User's Manual
66
Sectio
n 4
Installin
g T
ags
Section 4Installation
MEMO
RFID SystemUser's Manual
Section 5Chemical Resistance
Chemical Resistance of the Antennas 68
Sectio
n 5
Ch
emical R
esistance
Chemical Resistance of Tags 69
Degree of Protection 72
67RFID System
User's Manual
68
Sectio
n 5
Ch
emical R
esistance o
f the A
nten
nas
Section 5Chemical Resistance
Chemical Resistance of the Antennas
Applicable Models
ABS resin is used for case material and epoxy resin for filling material. Refer to the following lists and do not
use chemicals that affect ABS and epoxy resin.
Chemicals That Cause Deformations, Cracks, Etc.
Chemicals That May Cause Discoloration, Swelling, Etc.
Chemicals That Do Not Affect ABS Resin or Epoxy Resin
Note: The above results are from tests conducted a room temperature (23°C). Even if the chemicals
do not affect the ABS or epoxy resins at room temperature, they may affect the resins at higher
or lower temperatures. Check the chemicals carefully in advance.
V680-HS63-W/R V680-HS52-W/R V680-HS65-W/R
ABS resin Epoxy resin
Trichlene, acetone, xylene, toluene, gasoline, creosol, methylene chloride, phenol, cyclohexane, aqua regia, chromic acid, sulfuric acid (90% RT), methyl ethyl ketone, aniline, nitrobenzine, monochlorobenzine, pyridine, nitric acid (60% RT), formic acid (80% RT)
Aqua regia, chromic acid, sulfuric acid (90% RT), nitric acid (60% RT), ammonia solution, acetone, methylene chloride, phenol
ABS resin Epoxy resin
Hydrochloric acid, alcohol, Freon, sodium hydroxide, hydrogen peroxide, benzine, sulfuric acid (10% RT), nitric acid (10% RT), phosphoric acid (85% RT), ammonia solution
Sulfuric acid (10% RT), nitric acid (10% RT), hydrochlo-ric acid (30% RT), acetic acid (50% RT), oxalic acid, calcium hydroxide, benzine, creosol, alcohol, cyclohex-ane, toluene, xylene, benzine, grease
ABS resin Epoxy resin
Ammonia, kerosine, mineral oil, developer, Yushiroken S50, Chemi-Cool Z, Velocity No. 3, Yushiroken EEE-30Y, petroleum, grease, acetic acid, oxalic acid, cal-cium hydroxide, phosphoric acid (30% RT), hydrochlo-ric acid (10% RT), potassium hydroxide
Ammonia, hydrochloric acid (10% RT), potassium hydroxide, petroleum, gasoline, Yushiroken S50, Chemi-Cool Z, Velocity No. 3, Yushiroken EEE-30Y
RFID SystemUser's Manual
Sectio
n 5
Ch
emical R
esistance o
f Tag
sSection 5
Chemical Resistance
Chemical Resistance of Tags
Applicable Models
Chemicals that affect Tags are shown below.
ABS resin is used for case material and epoxy resin for filling material. Refer to the following lists and do not
use chemicals that affect ABS and epoxy resin.
Tags cannot be used in applications with explosion-proof specifications.
Chemicals That Cause Deformations, Cracks, Etc.
Chemicals That May Cause Discoloration, Swelling, Etc.
Chemicals That Do Not Affect ABS Resin or Epoxy Resin
Note: The above results are from tests conducted a room temperature (23°C). Even if the chemicalsdo not affect the ABS or epoxy resins at room temperature, they may affect the resins at higheror lower temperatures. Check the chemicals carefully in advance.
V680-D2KF67/67M
ABS resin Epoxy resin
Trichlene, acetone, xylene, toluene, gasoline, creosol, methylene chloride, phenol, cyclohexane, aqua regia, chromic acid, sulfuric acid (90% RT), methyl ethyl ketone, aniline, nitrobenzine, monochlorobenzine, pyridine, nitric acid (60% RT), formic acid (80% RT)
Aqua regia, chromic acid, sulfuric acid (90% RT), nitric acid (60% RT), ammonia solution, acetone, methylene chloride, phenol
ABS resin Epoxy resin
Hydrochloric acid, alcohol, Freon, sodium hydroxide, hydrogen peroxide, benzine, sulfuric acid (10% RT), nitric acid (10% RT), phosphoric acid (85% RT), ammonia solution
Sulfuric acid (10% RT), nitric acid (10% RT), hydrochlo-ric acid (30% RT), acetic acid (50% RT), oxalic acid, calcium hydroxide, benzine, creosol, alcohol, cyclohex-ane, toluene, xylene, benzine, grease
ABS resin Epoxy resin
Ammonia, kerosine, mineral oil, developer, Yushiroken S50, Chemi-Cool Z, Velocity No. 3, Yushiroken EEE-30Y, petroleum, grease, acetic acid, oxalic acid, cal-cium hydroxide, phosphoric acid (30% RT), hydrochlo-ric acid (10% RT), potassium hydroxide
Ammonia, hydrochloric acid (10% RT), potassium hydroxide, petroleum, gasoline, Yushiroken S50, Chemi-Cool Z, Velocity No. 3, Yushiroken EEE-30Y
69RFID System
User's Manual
70
Sectio
n 5
Ch
emical R
esistance o
f Tag
s
Section 5Chemical Resistance
Applicable Model
PPS resin is used for case material and epoxy resin for filling material. Refer to the following lists and do not
use chemicals that affect PPS and epoxy resin.
Tags cannot be used in applications with explosion-proof specifications.
Chemicals That Cause Deformations, Cracks, Etc.
Chemicals That May Cause Discoloration, Swelling, Etc.
Chemicals that Do Not Affect PPS Resin or Epoxy Resin
Note: The above results are from tests conducted a room temperature (23°C). Even if the chemicals
do not affect the PPS or epoxy resins at room temperature, they may affect the resins at higher
or lower temperatures. Check the chemicals carefully in advance.
V680-D2KF52M
PPS resin Epoxy resin
Aqua regia Aqua regia, chromic acid, sulfuric acid (90% RT), nitric acid (60% RT), ammonia solution, acetone, methylene chloride, phenol
PPS resin Epoxy resin
Nitric acid (60% RT) Sulfuric acid (10% RT), nitric acid (10% RT), hydrochlo-ric acid (30% RT), acetic acid (50% RT), oxalic acid, calcium hydroxide, benzine, creosol, alcohol, cyclohex-ane, toluene, xylene, benzine, grease
PPS resin Epoxy resin
Hydrochloric acid (37%RT), sulfuric acid (98%RT), nitric acid (40%RT), Hydrogen fluoride solution (40%RT), chromic acid (40%RT), hydrogen peroxide (28%RT), sodium hydroxide solution (60%RT), ammonia solution (28%RT), sodium chloride (10%RT), sodium carbonate (20%RT), sodium hypochlorite, phenol solution (5%RT), glacial acetic acid, acetic acid, oleic acid, Methyl alcohol (95%RT), ethyl alcohol (95%RT), Ethyl acetate, sebacic acid, diethylhexyl, acetone, diethyl ether, n-heptane, 2-2-4 trimethylpen-tane, benzine, toluene, aniline, mineral oil, gasoline, insulating oil, dichloroethylene, carbon tetrachloride
Ammonia, hydrochloric acid (10% RT), potassium hydroxide, petroleum, gasoline, Yushiroken S50, Chemi-Cool Z, Velocity No. 3, Yushiroken EEE-30Y, methyl ethyl ketone, sodium hydroxide (10%RT)
RFID SystemUser's Manual
Sectio
n 5
Ch
emical R
esistance o
f Tag
sSection 5
Chemical Resistance
Applicable Model
Chemicals that affect Tags are shown below.
Polybutylene terephthalate (PBT) resin is used for case material and epoxy resin for filling material. Refer to
the following lists and do not use chemicals that affect PBT and epoxy resins.
Tags cannot be used in applications with explosion-proof specifications.
Chemicals That Cause Deformations, Cracks, Etc.
Chemicals That May Cause Discoloration, Swelling, Etc.
Chemicals that Do Not Affect PPS Resin or Epoxy Resin
Note: The above results are from tests conducted at room temperature (23°C). Even if the chemicals
do not affect the PPS or epoxy resins at room temperature, they may affect the resins at higher
or lower temperatures. Check the chemicals carefully in advance.
V680-D8KF68/D32KF68
PBT resin Epoxy resin
Acetone, trichloroethylene, ethylene dichloride, sodium hydroxide, and other alkaline substances
Aqua regia, chromic acid, sulfuric acid (90% RT), nitric acid (60% RT), liquid ammonia, acetone, methylene chloride, phenol
PBT resin Epoxy resin
Hydrochloric acid (10% RT), acetic acid (5% RT), ben-zene
Sulfuric acid (10% RT), nitric acid (10% RT), concen-trated hydrochloric acid, acetic acid (50% RT), nitric acid, calcium hydroxide, benzene, cresol, alcohol, microhexanon, toluene, xylene, benzene, grease
PBT resin Epoxy resin
Nitric acid (30% RT), concentrated hydrochloric acid, acetic acid, ethyl acetate (100% RT), potassium perma-ganate (5% RH), ethyl acetate, carbon tetrachloride, methanol, ethanol, gasoline
Ammonia, hydrochloric acid (10% RT), calcium hydrox-ide, petroleum, gasoline, Yushiroken S50, Chemi-cool Z, Velocity No. 3, Yushiroken EEE-30Y, methyl ethyl ketone, sodium hydroxide
71RFID System
User's Manual
72
Sectio
n 5
Deg
ree of P
rotectio
n
Section 5Chemical Resistance
Degree of Protection
Ingress protection degrees (IP-@@) are determined by the following tests. Be sure to check the sealing capa-
bility under the actual operating environment and conditions before actual use.
IP indicates the ingress protection symbol.
IEC (International Electrotechnical Commission) StandardsIEC 60529: 1989-11
(A) First Digit: Degree of Protection from Solid Materials
(B) Second Digit: Degree of Protection Against Water
Degree Degree
0 No protection
1Protects against penetration of any solid object such as a hand that is 50 mm or more in diameter.
2Protects against penetration of any solid object, such as a finger, that is 12.5 mm or more in diame-ter.
3
Protects against penetration of any solid object, such as a wire, that is 2.5 mm or more in diameter.
4
Protects against penetration of any solid object, such as a wire, that is 1 mm or more in diameter.
5
Protects against penetration of dust of a quantity that may cause malfunction or obstruct the safe operation of the product.
6
Protects against penetration of all dust.
Degree Protection Test method (with pure water)
0 No protection Not protected against water. No test
1 Protection against water drops
Protects against vertical drops of water towards the product.
Water is dropped vertically towards the product from the test machine for 10 min.
2 Protection against water drop
Protects against drops of water approaching at a maxi-mum angle of 15° to the left, right, back, and front from ver-tical towards the product.
Water is dropped for 2.5 min each (i.e., 10 min in total) towards the product inclined 15° to the left, right, back, and front from the test machine.
50 mm dia.
12.5 mm dia.
2.5 mm
1 mm
200 mm
200 mm15˚
RFID SystemUser's Manual
Sectio
n 5
Deg
ree of P
rotectio
nSection 5
Chemical Resistance
Oil resistance (OMRON in-house standard)
Note: This OMRON in-house standard confirms resistance to cutting and other oils. It is equivalent to the
former JEM standard.
3 Protection against sprin-kled water
Protects against sprinkled water approaching at a maxi-mum angle of 60° from verti-cal towards the product.
Water is sprinkled for 10 min at a maximum angle of 60° to the left and right from vertical from the test machine.
4 Protection against water spray
Protects against water spray approaching at any angle towards the product.
Water is sprayed at any angle towards the product for 10 min from the test machine.
5 Protection against water jet spray
Protects against water jet spray approaching at any angle towards the product.
Water is jet sprayed at any angle towards the product for 1 min per square meter for at least 3 min in total from the test machine.
6 Protection against high pressure water jet spray
Protects against high-pres-sure water jet spray approach-ing at any angle towards the product.
Water is jet sprayed at any angle towards the product for 1 min per square meter for at least 3 min in total from the test machine.
7 Protection underwater Resists the penetration of water when the product is placed underwater at speci-fied pressure for a specified time.
The product is placed 1 m deep in water (if the product is 850 mm max. in height) for 30 min.
8 Protection underwater Can be used continuously underwater.
The test method is determined by the manufacturer and user.
Protection
Oil-resistant No adverse affect from oil drops or oil spray approaching from any direction.
Oil-proof Protects against penetration of oil drops or oil spray approaching from any direction.
Degree Protection Test method (with pure water)
Water rate is 0.07 liter/min per hole.
Water rate is 0.07 liter/min per hole.
2.5 to 3 m
12.5 liter/min
Discharging nozzle: 6.3 dia.
2.5 to 3 m 100 liter/min
Discharging nozzle: 6.3 dia.
1 m
73RFID System
User's Manual
74RFID SystemUser's Manual
Revision HistoryA manual revision code appears as a suffix to the catalog number at the bottom of the front and rear pages.
Revision code Date Revised contents
01 October 2006 Original production
02 May 2007 Added items for V680-D8KF68/-D32KF68 ID Tags.
03 July 2007Added items for V680-A81, V680-HS65 Antenna, and the overseas regulations and standards.
03A September 2007Added information on metal on back surface of the V680-HS65, corrected Tag specifications, and made other minor corrections.
Cat. No.: Z248-E1-03A
Revision code
Terms and Conditions of Sale1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,catalogs, manuals, brochures and other documents, whether electronic or inwriting, relating to the sale of products or services (collectively, the "Products")by Omron Electronics LLC and its subsidiary companies (“Omron”). Omronobjects to any terms or conditions proposed in Buyer’s purchase order or otherdocuments which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-out notice by Omron. Omron reserves the right to increase or decrease priceson any unshipped portions of outstanding orders. Payments for Products aredue net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoicessent to Buyer after deducting transportation charges, taxes and duties, and willbe allowed only if (i) the invoice is paid according to Omron’s payment termsand (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month orthe maximum legal rate, whichever is less, on any balance not paid within thestated terms.
5. Orders. Omron will accept no order less than $200 net billing. 6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than generalreal property and income taxes), including any interest or penalties thereon,imposed directly or indirectly on Omron or required to be collected directly orindirectly by Omron for the manufacture, production, sale, delivery, importa-tion, consumption or use of the Products sold hereunder (including customsduties and sales, excise, use, turnover and license taxes) shall be charged toand remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactoryto Omron, Omron reserves the right to stop shipments or require satisfactorysecurity or payment in advance. If Buyer fails to make payment or otherwisecomply with these Terms or any related agreement, Omron may (without liabil-ity and in addition to other remedies) cancel any unshipped portion of Prod-ucts sold hereunder and stop any Products in transit until Buyer pays allamounts, including amounts payable hereunder, whether or not then due,which are owing to it by Buyer. Buyer shall in any event remain liable for allunpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellationunless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in deliveryresulting from causes beyond its control, including earthquakes, fires, floods,strikes or other labor disputes, shortage of labor or materials, accidents tomachinery, acts of sabotage, riots, delay in or lack of transportation or therequirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shallpass from Omron to Buyer; provided that Omron shall retain a security inter-est in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; ande. Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writingto Omron within 30 days of receipt of shipment and include the original trans-portation bill signed by the carrier noting that the carrier received the Productsfrom Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that theProducts will be free from defects in materials and workmanship for a period oftwelve months from the date of sale by Omron (or such other period expressedin writing by Omron). Omron disclaims all other warranties, express or implied.(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THEPRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIRINTENDED USE. Omron further disclaims all warranties and responsibility ofany type for claims or expenses based on infringement by the Products or oth-erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-gation hereunder shall be, at Omron’s election, to (i) replace (in the formoriginally shipped with Buyer responsible for labor charges for removal orreplacement thereof) the non-complying Product, (ii) repair the non-complyingProduct, or (iii) repay or credit Buyer an amount equal to the purchase price ofthe non-complying Product; provided that in no event shall Omron be responsi-ble for warranty, repair, indemnity or any other claims or expenses regardingthe Products unless Omron’s analysis confirms that the Products were prop-erly handled, stored, installed and maintained and not subject to contamina-tion, abuse, misuse or inappropriate modification. Return of any Products byBuyer must be approved in writing by Omron before shipment. Omron Compa-nies shall not be liable for the suitability or unsuitability or the results from theuse of Products in combination with any electrical or electronic components,circuits, system assemblies or any other materials or substances or environ-ments. Any advice, recommendations or information given orally or in writing,are not to be construed as an amendment or addition to the above warranty.See http://www.omron247.com or contact your Omron representative for pub-lished information.
14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLEFOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANYWAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM ISBASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.Further, in no event shall liability of Omron Companies exceed the individualprice of the Product on which liability is asserted.
15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies andtheir employees from and against all liabilities, losses, claims, costs andexpenses (including attorney's fees and expenses) related to any claim, inves-tigation, litigation or proceeding (whether or not Omron is a party) which arisesor is alleged to arise from Buyer's acts or omissions under these Terms or inany way with respect to the Products. Without limiting the foregoing, Buyer (atits own expense) shall indemnify and hold harmless Omron and defend or set-tle any action brought against such Companies to the extent based on a claimthat any Product made to Buyer specifications infringed intellectual propertyrights of another party.
16. Property; Confidentiality. Any intellectual property in the Products is the exclu-sive property of Omron Companies and Buyer shall not attempt to duplicate itin any way without the written permission of Omron. Notwithstanding anycharges to Buyer for engineering or tooling, all engineering and tooling shallremain the exclusive property of Omron. All information and materials suppliedby Omron to Buyer relating to the Products are confidential and proprietary,and Buyer shall limit distribution thereof to its trusted employees and strictlyprevent disclosure to any third party.
17. Export Controls. Buyer shall comply with all applicable laws, regulations andlicenses regarding (i) export of products or information; (iii) sale of products to“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens ofregulated technology or information.
18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any rightand no course of dealing between Buyer and Omron shall operate as a waiverof rights by Omron. (b) Assignment. Buyer may not assign its rights hereunderwithout Omron's written consent. (c) Law. These Terms are governed by thelaw of the jurisdiction of the home office of the Omron company from whichBuyer is purchasing the Products (without regard to conflict of law princi-ples). (d) Amendment. These Terms constitute the entire agreement betweenBuyer and Omron relating to the Products, and no provision may be changedor waived unless in writing signed by the parties. (e) Severability. If any provi-sion hereof is rendered ineffective or invalid, such provision shall not invalidateany other provision. (f) Setoff. Buyer shall have no right to set off any amountsagainst the amount owing in respect of this invoice. (g) Definitions. As usedherein, “including” means “including without limitation”; and “Omron Compa-nies” (or similar words) mean Omron Corporation and any direct or indirectsubsidiary or affiliate thereof.
Certain Precautions on Specifications and Use1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of theProduct in the Buyer’s application or use of the Product. At Buyer’s request,Omron will provide applicable third party certification documents identifyingratings and limitations of use which apply to the Product. This information byitself is not sufficient for a complete determination of the suitability of the Prod-uct in combination with the end product, machine, system, or other applicationor use. Buyer shall be solely responsible for determining appropriateness ofthe particular Product with respect to Buyer’s application, product or system.Buyer shall take application responsibility in all cases but the following is anon-exhaustive list of applications for which particular attention must be given:(i) Outdoor use, uses involving potential chemical contamination or electricalinterference, or conditions or uses not described in this document.(ii) Use in consumer products or any use in significant quantities. (iii) Energy control systems, combustion systems, railroad systems, aviationsystems, medical equipment, amusement machines, vehicles, safety equip-ment, and installations subject to separate industry or government regulations. (iv) Systems, machines and equipment that could present a risk to life or prop-erty. Please know and observe all prohibitions of use applicable to this Prod-uct. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUSRISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUTENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THEOVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Omron Companies shall not be responsible for theuser’s programming of a programmable Product, or any consequence thereof.
3. Performance Data. Data presented in Omron Company websites, catalogsand other materials is provided as a guide for the user in determining suitabil-ity and does not constitute a warranty. It may represent the result of Omron’stest conditions, and the user must correlate it to actual application require-ments. Actual performance is subject to the Omron’s Warranty and Limitationsof Liability.
4. Change in Specifications. Product specifications and accessories may bechanged at any time based on improvements and other reasons. It is our prac-tice to change part numbers when published ratings or features are changed,or when significant construction changes are made. However, some specifica-tions of the Product may be changed without any notice. When in doubt, spe-cial part numbers may be assigned to fix or establish key specifications foryour application. Please consult with your Omron’s representative at any timeto confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has beenchecked and is believed to be accurate; however, no responsibility is assumedfor clerical, typographical or proofreading errors or omissions.
Specifications subject to change without notice.Printed in the U.S.A.
OMRON ELECTRONICS LLC
1 Commerce DriveSchaumburg, IL 60173 847.843.7900 For US technical support or other inquiries: 800.556.6766
OMRON CANADA, INC. 885 Milner AvenueToronto, Ontario M1B 5V8416.286.6465
OMRON ON-LINEGlobal - www.omron.comUSA - www.omron247.comCanada - www.omron.caBrazil - www.omron.com.brLatin America - www.espanol.omron.com
Z248-E1-03A ©2007 OMRON ELECTRONICS LLC
UNITED STATESTo locate a Regional Sales Office, local Distributor orto obtain product information, call: 847.843.7900
MEXICO SALES OFFICES
Mexico, D.F. 555.660.3144Ciudad Juárez 656.623.7083Monterrey, N.L 818.377.4281Querétaro 442.135.4510
BRAZIL SALES OFFICESao Paulo 55.11.2101.6310
ARGENTINA SALES OFFICECono Sur 54.114.787.1129
OTHER LATIN AMERICAN SALES [email protected]