09-2010, Rev. 0910

www.tycoelectronics.com© 2010 Tyco Electronics Ltd.

Datasheets and product specification ac-cording to IEC 61810-1 and to be used only together with the ‘Definitions’ section.

Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.tycoelectronics.com/definitions

Datasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.

1

Axicom

n Y-Designn Frequency range DC to 6GHzn Impedance 50Ωn Small dimensions (16x7.6x10mm)n 1 form C contact (1 changeover contact)n Immersion cleanablen Low power consumption (≤140mW)

Typical applications Measurement and test equipment ATE, wireless base stations and antennas, wireless infrastructure, RF power amplifier

Contact Data Contact arrangement 1 form C, 1 CO Max. switching voltage 220VDC, 250VACRated current 2A Limiting continuous current 2ASwitching power 60W, 62.5VA, 50W (2.5GHz)Max. continuos RF-power at 20°C. 50W (2.5GHz)Contact material Ag, Au covered Minimum switching voltage 100µV Initial contact resistance <100mΩ at 10mA/20mVOperate time typ. 3ms, max. 5ms Release time without diode in parallel typ. 2ms, max. 5ms with diode in parallel typ. 4ms, max. 6ms Bounce time max. typ. 1ms, max. 3msMechanical endurance 107 operations

Coil Data Coil voltage range 3 to 24VDC

Coil versions, 50Ω version, monostable Coil Rated Operate Limiting Release Coil Rated coil code voltage voltage voltage voltage resistance power VDC VDC VDC VDC Ω±10% mW 51 3 2.25 6.50 0.30 64 140 52 4.5 3.38 9.80 0.45 145 140 53 5 3.75 10.90 0.50 178 140 54 6 4.50 13.00 0.60 257 140 55 9 6.75 19.60 0.90 574 140 56 12 9.00 26.10 1.20 1028 140 57 24 18.00 52.30 2.40 4114 140All figures are given for coil without pre-energization, at ambient temperature +23°C.

Contact Data (continued)

Coil versions, bistable Coil Rated Set Limiting Reset Coil Rated coil code voltage voltage voltage voltage resistance power VDC VDC VDC VDC Ω±10% mW50Ω version, Bistable, 1 coil 71 3 2.25 9.20 -2.25 128 70 72 4.5 3.38 13.85 -3.38 289 70 73 5 3.75 15.30 -3.75 357 70 74 6 4.50 18.50 -4.50 514 70 75 9 6.75 27.70 -6.75 1157 70 76 12 9.00 37.00 -9.00 2057 70 77 24 18.00 74.00 -18.00 8228 7050Ω version, bistable, 2 coils 91 3 2.25 6.50 2.25 64 140 92 4.5 3.38 9.80 3.38 145 140 93 5 3.75 10.90 3.75 178 140 94 6 4.50 13.00 4.50 257 140 95 9 6.75 19.60 6.75 574 140 96 12 9.00 26.10 9.00 1028 140 97 24 18.00 52.30 18.00 4114 140All figures are given for coil without pre-energization, at ambient temperature +23°C.

HF6 Relay

RF Signal Relays

Sep. 07, Rev. B

All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 12

Telecom-, Signal and RF Relays

HF6 Relay

Umax. at 0 A

Uop. min.

Urel. min.

140 mW

Coil V

olta

ge [U

/Uno

m]

Ambient Temperature [°C]

Terminal assignment

Relay top view

Non-latching type,

not energized condition

Latching type, 2 coils

reset condition

Latching type, 1 coil

rest condition

Coil Operating Range

0

0.5

1

1.5

2

2.5

3

3.5

-55 -45 -35 -25 -15 -5 5 15 25 35 45 55 65 75 85 95 105 115 125 135

U nom. nominal coil voltage

Umax. at 0 A

Uop. min.

70 mW

Coil V

olta

ge [U

/Uno

m]

Ambient Temperature [°C]

U nom. nominal coil voltage

Unom = Nominal coil voltageUmax. = Upper limit of the operative range of the coil voltage (limiting voltage)Uop. min. = Lower limit of the operative range of the coil voltage (reliable operate voltage) For latching relays Uset min. resp. Ureset min.Urel. min. = Lower limit of the operative range of the coil voltage (reliable release voltage)

140 mW 70 mW

Sep. 07, Rev. B

All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 12

Telecom-, Signal and RF Relays

HF6 Relay

Umax. at 0 A

Uop. min.

Urel. min.

140 mW

Coil V

olta

ge [U

/Uno

m]

Ambient Temperature [°C]

Terminal assignment

Relay top view

Non-latching type,

not energized condition

Latching type, 2 coils

reset condition

Latching type, 1 coil

rest condition

Coil Operating Range

0

0.5

1

1.5

2

2.5

3

3.5

-55 -45 -35 -25 -15 -5 5 15 25 35 45 55 65 75 85 95 105 115 125 135

U nom. nominal coil voltage

Umax. at 0 A

Uop. min.

70 mW

Coil V

olta

ge [U

/Uno

m]

Ambient Temperature [°C]

U nom. nominal coil voltage

Unom = Nominal coil voltageUmax. = Upper limit of the operative range of the coil voltage (limiting voltage)Uop. min. = Lower limit of the operative range of the coil voltage (reliable operate voltage) For latching relays Uset min. resp. Ureset min.Urel. min. = Lower limit of the operative range of the coil voltage (reliable release voltage)

140 mW 70 mW

09-2010, Rev. 0910

www.tycoelectronics.com© 2010 Tyco Electronics Ltd.

Datasheets and product specification ac-cording to IEC 61810-1 and to be used only together with the ‘Definitions’ section.

Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.tycoelectronics.com/definitions

Datasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.

2

AxicomRF Signal Relays

HF6 Relay (Continued)

Other Data Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content refer to the Product Compliance Support Center at www.tycoelectronics.com/customersupport/rohssupportcenterAmbient temperature -55°C to +85°C Thermal resistance <165K/W Category of environmental protection IEC 61810 RT III - wash tight Degree of protection, IEC 60529 IP 67, immersion cleanable Vibration resistance (functional) 35g, 10 to 1000Hz Shock resistance (functional), half sinus 11ms 50g Shock resistance (destructive), half sinus 0.5ms 150gTerminal type SMT Weight max. 3gResistance to soldering heat SMT IEC 60068-2-58 265°C/10s Moisture sensitive level, JEDEC J-Std-020D MSL3 Ultrasonic cleaning not recommendedPackaging/unit, SMT reel/250 pcs., box/250 pcs.

Insulation Data Initial dielectric strength between open contacts 600Vrms between contact and coil 1000VrmsInitial surge withstand voltage between open contacts 1000V between contact and coil 1500V

RF DataIsolation at 900MHz/3GHz/6GHz -80dB/-60dB/-30dB Insertion loss at 900MHz/3GHz/6GHz -0.05dB/-0.15dB/-0.80dB Voltage standing wave ratio (VSWR) at 900MHz/3GHz/6GHz 1.05/1.10/1.40Typical RF performance, 50Ω version

108-98022 Rev. D

8 of 12

Telecom-, Signal and RF Relays

HF6 Relay

AXICOM

Frequency [GHz] 0.9 3 6

Insertion-loss [dB] -0.05 -0.15 -0.80

Isolation [dB] -80 -60 -30

VSWR 1.05 1.1 1.4

High Frequency Data

1 Values given at frequency of 2.5 GHz

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

0

0 1 2 3 4 5

Frequencycc [GHz]

Isol

atio

n[d

B]

-0.8

-0.7

-0.6

-0.5

-0.4

-0.3

-0.2

-0.1

0

0 1 2 3 4 5

Inse

rtio

n-lo

ss[d

B]

1.00

1.10

1.20

1.30

1.40

1.50

1.60

0 1 2 3 4 5

VS

WR

108-98022 Rev. D

8 of 12

Telecom-, Signal and RF Relays

HF6 Relay

AXICOM

Frequency [GHz] 0.9 3 6

Insertion-loss [dB] -0.05 -0.15 -0.80

Isolation [dB] -80 -60 -30

VSWR 1.05 1.1 1.4

High Frequency Data

1 Values given at frequency of 2.5 GHz

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

0

0 1 2 3 4 5

Frequencycc [GHz]

Isol

atio

n[d

B]

-0.8

-0.7

-0.6

-0.5

-0.4

-0.3

-0.2

-0.1

0

0 1 2 3 4 5

Inse

rtio

n-lo

ss[d

B]

1.00

1.10

1.20

1.30

1.40

1.50

1.60

0 1 2 3 4 5

VS

WR

108-98022 Rev. D

8 of 12

Telecom-, Signal and RF Relays

HF6 Relay

AXICOM

Frequency [GHz] 0.9 3 6

Insertion-loss [dB] -0.05 -0.15 -0.80

Isolation [dB] -80 -60 -30

VSWR 1.05 1.1 1.4

High Frequency Data

1 Values given at frequency of 2.5 GHz

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

0

0 1 2 3 4 5

Frequencycc [GHz]

Isol

atio

n[d

B]

-0.8

-0.7

-0.6

-0.5

-0.4

-0.3

-0.2

-0.1

0

0 1 2 3 4 5

Inse

rtio

n-lo

ss[d

B]

1.00

1.10

1.20

1.30

1.40

1.50

1.60

0 1 2 3 4 5

VS

WR

Terminal assignmentTOP view on component side of PCBMonostable Bistable, 1 coil

Contacts are shown in reset condition. Contact position might change during transportation and must be reset before use.

Bistable, 2 coils

PCB layout TOP view on component side of PCB

09-2010, Rev. 0910

www.tycoelectronics.com© 2010 Tyco Electronics Ltd.

Datasheets and product specification ac-cording to IEC 61810-1 and to be used only together with the ‘Definitions’ section.

Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.tycoelectronics.com/definitions

Datasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.

3

AxicomRF Signal Relays

HF6 Relay (Continued)

Dimensions Processing

full line: typicaldotted line: process limits

external preheating

240°C

180°C

130°C

100°C

forced cooling

20 to 40s

Time [s]

Tem

pera

ture

[°C

]

Vapour phase solderingtemperature/time profile(lead and housing peak temp.)

Recommended soldering conditionsVapour phase soldering

Time [s]

Tem

pera

ture

[°C

]Recommended reflow soldering profile

Infrared solderingtemperature/time profile(lead and housing peak temp.)

Time [s]

Tem

pera

ture

[°C

]

Resistance to soldering heat

Infrared solderingtemperature/time profile(lead and housing peak temp.)

Packing

Tape and reel for SMT

Reel dimensions

09-2010, Rev. 0910

www.tycoelectronics.com© 2010 Tyco Electronics Ltd.

Datasheets and product specification ac-cording to IEC 61810-1 and to be used only together with the ‘Definitions’ section.

Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.tycoelectronics.com/definitions

Datasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.

4

AxicomRF Signal Relays

HF6 Relay (Continued)

Product code structure Typical product code HF6 53

Type HF6 High Frequency Relays HF6 Series 1 form C, 1 COCoil Coil code: please refer to coil versions table Performance type 5x 50 Ohm version, monostable 1coil 7x 50 Ohm version, bistable 1coil 9x 50 Ohm version, bistable 2coils

Product code Arrangement Version Coil Coil type Part number HF6 51 1 form C (1 CO) 50Ω 3VDC Monostable 1462052-1 HF6 52 1 form C (1 CO) 50Ω 4.5VDC Monostable 1462052-2 HF6 53 1 form C (1 CO) 50Ω 5VDC Monostable 1462052-3 HF6 54 1 form C (1 CO) 50Ω 6VDC Monostable 1462052-4 HF6 55 1 form C (1 CO) 50Ω 9VDC Monostable 1462052-5 HF6 56 1 form C (1 CO) 50Ω 12VDC Monostable 1462052-6 HF6 57 1 form C (1 CO) 50Ω 24VDC Monostable 1462052-7 HF6 71 1 form C (1 CO) 50Ω 3VDC Bistable 1 coil 1462052-8 HF6 72 1 form C (1 CO) 50Ω 4.5VDC Bistable 1 coil 1462052-9 HF6 73 1 form C (1 CO) 50Ω 5VDC Bistable 1 coil 1-1462052-0 HF6 74 1 form C (1 CO) 50Ω 6VDC Bistable 1 coil 1-1462052-1 HF6 75 1 form C (1 CO) 50Ω 9VDC Bistable 1 coil 1-1462052-2 HF6 76 1 form C (1 CO) 50Ω 12VDC Bistable 1 coil 1-1462052-3 HF6 77 1 form C (1 CO) 50Ω 24VDC Bistable 1 coil 1-1462052-4 HF6 91 1 form C (1 CO) 50Ω 3VDC Bistable 2 coils 1-1462052-5 HF6 92 1 form C (1 CO) 50Ω 4.5VDC Bistable 2 coils 1-1462052-6 HF6 93 1 form C (1 CO) 50Ω 5VDC Bistable 2 coils 1-1462052-7 HF6 94 1 form C (1 CO) 50Ω 6VDC Bistable 2 coils 1-1462052-8 HF6 95 1 form C (1 CO) 50Ω 9VDC Bistable 2 coils 1-1462052-9 HF6 96 1 form C (1 CO) 50Ω 12VDC Bistable 2 coils 2-1462052-0 HF6 97 1 form C (1 CO) 50Ω 24VDC Bistable 2 coils 2-1462052-1