revisionlecture1: nodal analysis
TRANSCRIPT
![Page 1: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/1.jpg)
Revision Lecture 1: NodalAnalysis
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 1 / 13
![Page 2: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/2.jpg)
Exam
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 2 / 13
Exam Format
Question 1 (40%): eight short parts covering the whole syllabus.
Questions 2 and 3: single topic questions (answer both)
Syllabus
Does include: Everything in the notes.
Does not include: Two-port parameters (2008:1j), Gaussian elimination(2007:2c), Application areas (2008:3d), Nullators and Norators (2008:4c),Small-signal component models (2008:4e), Gain-bandwidth product(2006:4c), Zener Diodes (2008/9 syllabus), Non-ideal models of L, C andtransformer (2011/12 syllabus), Transmission lines VSWR and crankdiagram (2011/12 syllabus).
![Page 3: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/3.jpg)
Basic Concepts
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 3 / 13
• All the points in a circuit joined together with zero-resistance wiresmake up a single node. The voltage is the same at any point in anode.
![Page 4: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/4.jpg)
Basic Concepts
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 3 / 13
• All the points in a circuit joined together with zero-resistance wiresmake up a single node. The voltage is the same at any point in anode.
• Choose one node in a circuit to be the reference node. Measure allnode voltages relative to this one.
![Page 5: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/5.jpg)
Basic Concepts
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 3 / 13
• All the points in a circuit joined together with zero-resistance wiresmake up a single node. The voltage is the same at any point in anode.
• Choose one node in a circuit to be the reference node. Measure allnode voltages relative to this one.
• Voltage across a component is the difference between the voltagesat the two ends. VAB = VA − VB .
![Page 6: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/6.jpg)
Basic Concepts
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 3 / 13
• All the points in a circuit joined together with zero-resistance wiresmake up a single node. The voltage is the same at any point in anode.
• Choose one node in a circuit to be the reference node. Measure allnode voltages relative to this one.
• Voltage across a component is the difference between the voltagesat the two ends. VAB = VA − VB .
• Passive sign convention: Current and voltage arrows for a 2-terminalcomponent are in opposite directions.
![Page 7: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/7.jpg)
Basic Concepts
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 3 / 13
• All the points in a circuit joined together with zero-resistance wiresmake up a single node. The voltage is the same at any point in anode.
• Choose one node in a circuit to be the reference node. Measure allnode voltages relative to this one.
• Voltage across a component is the difference between the voltagesat the two ends. VAB = VA − VB .
• Passive sign convention: Current and voltage arrows for a 2-terminalcomponent are in opposite directions.
• Components are in parallel if they are joined together at both ends.Components in parallel have the same voltage across them.
![Page 8: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/8.jpg)
Basic Concepts
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 3 / 13
• All the points in a circuit joined together with zero-resistance wiresmake up a single node. The voltage is the same at any point in anode.
• Choose one node in a circuit to be the reference node. Measure allnode voltages relative to this one.
• Voltage across a component is the difference between the voltagesat the two ends. VAB = VA − VB .
• Passive sign convention: Current and voltage arrows for a 2-terminalcomponent are in opposite directions.
• Components are in parallel if they are joined together at both ends.Components in parallel have the same voltage across them.
• Components are in series if the same current is forced to flowthrough each one.
![Page 9: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/9.jpg)
Basic Concepts
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 3 / 13
• All the points in a circuit joined together with zero-resistance wiresmake up a single node. The voltage is the same at any point in anode.
• Choose one node in a circuit to be the reference node. Measure allnode voltages relative to this one.
• Voltage across a component is the difference between the voltagesat the two ends. VAB = VA − VB .
• Passive sign convention: Current and voltage arrows for a 2-terminalcomponent are in opposite directions.
• Components are in parallel if they are joined together at both ends.Components in parallel have the same voltage across them.
• Components are in series if the same current is forced to flowthrough each one.
• KCL (Kirchoff’s Current Law): The total current going out of a node(or any collection of nodes) sums to zero.
![Page 10: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/10.jpg)
Ohm’s Law
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 4 / 13
Ohm’s law relates the voltage drop acrossa resistor to the current flowing in it:
V = IZ
![Page 11: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/11.jpg)
Ohm’s Law
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 4 / 13
Ohm’s law relates the voltage drop acrossa resistor to the current flowing in it:
V = IZ
Passive Sign Convention: V and I arrows must point in opposite directions(otherwise you need a − sign in Ohm’s law)
![Page 12: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/12.jpg)
Ohm’s Law
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 4 / 13
Ohm’s law relates the voltage drop acrossa resistor to the current flowing in it:
V = IZ
Passive Sign Convention: V and I arrows must point in opposite directions(otherwise you need a − sign in Ohm’s law)
Voltage arrow means V = V tip − Vbase = VAB (subscript order oppositefrom vectors)
![Page 13: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/13.jpg)
Ohm’s Law
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 4 / 13
Ohm’s law relates the voltage drop acrossa resistor to the current flowing in it:
V = IZ
Passive Sign Convention: V and I arrows must point in opposite directions(otherwise you need a − sign in Ohm’s law)
Voltage arrow means V = V tip − Vbase = VAB (subscript order oppositefrom vectors)
Ohm’s law still true if all currents are in mA and all impedances in kΩ.
![Page 14: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/14.jpg)
Ohm’s Law
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 4 / 13
Ohm’s law relates the voltage drop acrossa resistor to the current flowing in it:
V = IZ
Passive Sign Convention: V and I arrows must point in opposite directions(otherwise you need a − sign in Ohm’s law)
Voltage arrow means V = V tip − Vbase = VAB (subscript order oppositefrom vectors)
Ohm’s law still true if all currents are in mA and all impedances in kΩ.
Ohm’s law still true if all currents and all voltages are RMS values:V = IZ where V = V√
2for a voltage phasor V .
![Page 15: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/15.jpg)
Nodal Analysis
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 5 / 13
(1) Pick any node as the voltage reference. Label its voltage as 0 V.Label any dependent sources with VS , IS , . . ..
(2) If any voltage sources are connected to a labelled node, label theirother ends by adding the value of the source onto the voltage of thelabelled end.
(3) Pick an unlabelled node and label it with X, Y, . . ., then loop back tostep (2) until all nodes are labelled.
(4) For each dependent source , write down an equation that expressesits value in terms of other node voltages.
(5) Write down a KCL equation for each “normal” node (i.e. one that is notconnected to a floating voltage source).
(6) Write down a KCL equation for each “super-node”. A super-nodeconsists of a set of nodes that are joined by floating voltage sourcesand includes any other components linking these nodes.
(7) Solve the set of simultaneous equations that you have written down.
![Page 16: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/16.jpg)
Nodal Analysis
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 5 / 13
(1) Pick any node as the voltage reference. Label its voltage as 0 V.Label any dependent sources with VS , IS , . . ..
(2) If any voltage sources are connected to a labelled node, label theirother ends by adding the value of the source onto the voltage of thelabelled end.
(3) Pick an unlabelled node and label it with X, Y, . . ., then loop back tostep (2) until all nodes are labelled.
(4) For each dependent source , write down an equation that expressesits value in terms of other node voltages.
(5) Write down a KCL equation for each “normal” node (i.e. one that is notconnected to a floating voltage source).
(6) Write down a KCL equation for each “super-node”. A super-nodeconsists of a set of nodes that are joined by floating voltage sourcesand includes any other components linking these nodes.
(7) Solve the set of simultaneous equations that you have written down.
![Page 17: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/17.jpg)
Nodal Analysis
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 5 / 13
(1) Pick any node as the voltage reference. Label its voltage as 0 V.Label any dependent sources with VS , IS , . . ..
(2) If any voltage sources are connected to a labelled node, label theirother ends by adding the value of the source onto the voltage of thelabelled end.
(3) Pick an unlabelled node and label it with X, Y, . . ., then loop back tostep (2) until all nodes are labelled.
(4) For each dependent source , write down an equation that expressesits value in terms of other node voltages.
(5) Write down a KCL equation for each “normal” node (i.e. one that is notconnected to a floating voltage source).
(6) Write down a KCL equation for each “super-node”. A super-nodeconsists of a set of nodes that are joined by floating voltage sourcesand includes any other components linking these nodes.
(7) Solve the set of simultaneous equations that you have written down.
![Page 18: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/18.jpg)
Nodal Analysis
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 5 / 13
(1) Pick any node as the voltage reference. Label its voltage as 0 V.Label any dependent sources with VS , IS , . . ..
(2) If any voltage sources are connected to a labelled node, label theirother ends by adding the value of the source onto the voltage of thelabelled end.
(3) Pick an unlabelled node and label it with X, Y, . . ., then loop back tostep (2) until all nodes are labelled.
(4) For each dependent source , write down an equation that expressesits value in terms of other node voltages.
(5) Write down a KCL equation for each “normal” node (i.e. one that is notconnected to a floating voltage source).
(6) Write down a KCL equation for each “super-node”. A super-nodeconsists of a set of nodes that are joined by floating voltage sourcesand includes any other components linking these nodes.
(7) Solve the set of simultaneous equations that you have written down.
![Page 19: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/19.jpg)
Nodal Analysis
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 5 / 13
(1) Pick any node as the voltage reference. Label its voltage as 0 V.Label any dependent sources with VS , IS , . . ..
(2) If any voltage sources are connected to a labelled node, label theirother ends by adding the value of the source onto the voltage of thelabelled end.
(3) Pick an unlabelled node and label it with X, Y, . . ., then loop back tostep (2) until all nodes are labelled.
(4) For each dependent source , write down an equation that expressesits value in terms of other node voltages.
(5) Write down a KCL equation for each “normal” node (i.e. one that is notconnected to a floating voltage source).
(6) Write down a KCL equation for each “super-node”. A super-nodeconsists of a set of nodes that are joined by floating voltage sourcesand includes any other components linking these nodes.
(7) Solve the set of simultaneous equations that you have written down.
![Page 20: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/20.jpg)
Nodal Analysis
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 5 / 13
(1) Pick any node as the voltage reference. Label its voltage as 0 V.Label any dependent sources with VS , IS , . . ..
(2) If any voltage sources are connected to a labelled node, label theirother ends by adding the value of the source onto the voltage of thelabelled end.
(3) Pick an unlabelled node and label it with X, Y, . . ., then loop back tostep (2) until all nodes are labelled.
(4) For each dependent source , write down an equation that expressesits value in terms of other node voltages.
(5) Write down a KCL equation for each “normal” node (i.e. one that is notconnected to a floating voltage source).
(6) Write down a KCL equation for each “super-node”. A super-nodeconsists of a set of nodes that are joined by floating voltage sourcesand includes any other components linking these nodes.
(7) Solve the set of simultaneous equations that you have written down.
![Page 21: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/21.jpg)
Nodal Analysis
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 5 / 13
(1) Pick any node as the voltage reference. Label its voltage as 0 V.Label any dependent sources with VS , IS , . . ..
(2) If any voltage sources are connected to a labelled node, label theirother ends by adding the value of the source onto the voltage of thelabelled end.
(3) Pick an unlabelled node and label it with X, Y, . . ., then loop back tostep (2) until all nodes are labelled.
(4) For each dependent source , write down an equation that expressesits value in terms of other node voltages.
(5) Write down a KCL equation for each “normal” node (i.e. one that is notconnected to a floating voltage source).
(6) Write down a KCL equation for each “super-node”. A super-nodeconsists of a set of nodes that are joined by floating voltage sourcesand includes any other components linking these nodes.
(7) Solve the set of simultaneous equations that you have written down.
![Page 22: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/22.jpg)
Nodal Analysis Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 6 / 13
8V
1k
2k3k
0
2V
![Page 23: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/23.jpg)
Nodal Analysis Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 6 / 13
(1) Pick reference node.
8V
1k
2k3k
0
2V
![Page 24: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/24.jpg)
Nodal Analysis Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 6 / 13
(1) Pick reference node.
(2) Label nodes: 88V
1k
2k3k
0
2V
8
![Page 25: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/25.jpg)
Nodal Analysis Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 6 / 13
(1) Pick reference node.
(2) Label nodes: 8, X8V
1k
2k3k
0
2V
8 X
![Page 26: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/26.jpg)
Nodal Analysis Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 6 / 13
(1) Pick reference node.
(2) Label nodes: 8, X and X + 2 sinceit is joined to X via a voltage source. 8V
1k
2k3k
0
2V
8 X
X+2
![Page 27: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/27.jpg)
Nodal Analysis Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 6 / 13
(1) Pick reference node.
(2) Label nodes: 8, X and X + 2 sinceit is joined to X via a voltage source.
(3) Write KCL equations but count all thenodes connected via floating voltagesources as a single “super-node” givingone equation
X−81 + X
2 + (X+2)−03 = 0
8V
1k
2k3k
0
2V
8 X
X+2
![Page 28: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/28.jpg)
Nodal Analysis Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 6 / 13
(1) Pick reference node.
(2) Label nodes: 8, X and X + 2 sinceit is joined to X via a voltage source.
(3) Write KCL equations but count all thenodes connected via floating voltagesources as a single “super-node” givingone equation
X−81 + X
2 + (X+2)−03 = 0
Ohm’s law always involves the differencebetween the voltages at either end of aresistor. (Obvious but easily forgotten)
8V
1k
2k3k
0
2V
8 X
X+2
![Page 29: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/29.jpg)
Nodal Analysis Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 6 / 13
(1) Pick reference node.
(2) Label nodes: 8, X and X + 2 sinceit is joined to X via a voltage source.
(3) Write KCL equations but count all thenodes connected via floating voltagesources as a single “super-node” givingone equation
X−81 + X
2 + (X+2)−03 = 0
Ohm’s law always involves the differencebetween the voltages at either end of aresistor. (Obvious but easily forgotten)
(4) Solve the equations: X = 4
8V
1k
2k3k
0
2V
8 X
X+2
![Page 30: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/30.jpg)
Voltage and Current Dividers
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 7 / 13
Components in series form a voltagedivider: Voltages ∝ R.
Vk
VTotal
= Rk
RTotal
![Page 31: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/31.jpg)
Voltage and Current Dividers
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 7 / 13
Components in series form a voltagedivider: Voltages ∝ R.
Vk
VTotal
= Rk
RTotal
Components in parallel form acurrent divider: Currents ∝ G.
IkITotal
= Gk
GTotal
![Page 32: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/32.jpg)
Voltage and Current Dividers
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 7 / 13
Components in series form a voltagedivider: Voltages ∝ R.
Vk
VTotal
= Rk
RTotal
Components in parallel form acurrent divider: Currents ∝ G.
IkITotal
= Gk
GTotal
Summing Junction: X is a weightedaverage with weights ∝ G.
X = G1V1+G2V2+G3V3
GTotal
![Page 33: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/33.jpg)
Voltage and Current Dividers
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 7 / 13
Components in series form a voltagedivider: Voltages ∝ R.
Vk
VTotal
= Rk
RTotal
Components in parallel form acurrent divider: Currents ∝ G.
IkITotal
= Gk
GTotal
Summing Junction: X is a weightedaverage with weights ∝ G.
X = G1V1+G2V2+G3V3
GTotal
Also works if Vk is zero (lessobvious).
![Page 34: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/34.jpg)
Superposition
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 8 / 13
Any voltage or current in a circuit is the sum of the effects of the sourcestaken one at a time.
![Page 35: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/35.jpg)
Superposition
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 8 / 13
Any voltage or current in a circuit is the sum of the effects of the sourcestaken one at a time.
To use superposition:
![Page 36: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/36.jpg)
Superposition
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 8 / 13
Any voltage or current in a circuit is the sum of the effects of the sourcestaken one at a time.
To use superposition:
• Set all the sources to zero except for the first one and find thevoltage at each node
A zero-valued voltage source is a short circuit
A zero-valued current source is an open circuit
![Page 37: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/37.jpg)
Superposition
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 8 / 13
Any voltage or current in a circuit is the sum of the effects of the sourcestaken one at a time.
To use superposition:
• Set all the sources to zero except for the first one and find thevoltage at each node
A zero-valued voltage source is a short circuit
A zero-valued current source is an open circuit
• Repeat for each of the sources and add up the results to get aformula for the voltage at each node.
![Page 38: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/38.jpg)
Superposition
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 8 / 13
Any voltage or current in a circuit is the sum of the effects of the sourcestaken one at a time.
To use superposition:
• Set all the sources to zero except for the first one and find thevoltage at each node
A zero-valued voltage source is a short circuit
A zero-valued current source is an open circuit
• Repeat for each of the sources and add up the results to get aformula for the voltage at each node.
• Express all dependent source values in terms of node voltages andeliminate them from the formulae. A source is dependent if its valueis determined by the voltages/currents elsewhere in the circuit.
![Page 39: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/39.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
![Page 40: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/40.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
• If we set U2 = 0 then the currentsource becomes an open circuit
![Page 41: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/41.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
• If we set U2 = 0 then the currentsource becomes an open circuit
![Page 42: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/42.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
• If we set U2 = 0 then the currentsource becomes an open circuit andnow the 3 k plays no part in the circuit.
![Page 43: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/43.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
• If we set U2 = 0 then the currentsource becomes an open circuit andnow the 3 k plays no part in the circuit.
![Page 44: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/44.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
• If we set U2 = 0 then the currentsource becomes an open circuit andnow the 3 k plays no part in the circuit.
2 k and 1 k form a potential divider andso X = 1 k
2 k+1 k = 13U1.
![Page 45: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/45.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
• If we set U2 = 0 then the currentsource becomes an open circuit andnow the 3 k plays no part in the circuit.
2 k and 1 k form a potential divider andso X = 1 k
2 k+1 k = 13U1.
• If we set U1 = 0 then thevoltage source becomes ashort circuit
![Page 46: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/46.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
• If we set U2 = 0 then the currentsource becomes an open circuit andnow the 3 k plays no part in the circuit.
2 k and 1 k form a potential divider andso X = 1 k
2 k+1 k = 13U1.
• If we set U1 = 0 then thevoltage source becomes ashort circuit
![Page 47: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/47.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
• If we set U2 = 0 then the currentsource becomes an open circuit andnow the 3 k plays no part in the circuit.
2 k and 1 k form a potential divider andso X = 1 k
2 k+1 k = 13U1.
• If we set U1 = 0 then thevoltage source becomes ashort circuit and the 2 kand 1 k are in parallel.
2 k||1 k = 2 k×1 k2 k+1 k = 2
3 k.
![Page 48: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/48.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
• If we set U2 = 0 then the currentsource becomes an open circuit andnow the 3 k plays no part in the circuit.
2 k and 1 k form a potential divider andso X = 1 k
2 k+1 k = 13U1.
• If we set U1 = 0 then thevoltage source becomes ashort circuit and the 2 kand 1 k are in parallel.
2 k||1 k = 2 k×1 k2 k+1 k = 2
3 k.
Now X = 23U2 .
![Page 49: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/49.jpg)
Superposition Example
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 9 / 13
Problem: Find X in terms of U1 and U2.
• If we set U2 = 0 then the currentsource becomes an open circuit andnow the 3 k plays no part in the circuit.
2 k and 1 k form a potential divider andso X = 1 k
2 k+1 k = 13U1.
• If we set U1 = 0 then thevoltage source becomes ashort circuit and the 2 kand 1 k are in parallel.
2 k||1 k = 2 k×1 k2 k+1 k = 2
3 k.
Now X = 23U2 .
• Combining these two gives X = 13U1 +
23U2.
![Page 50: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/50.jpg)
Thévenin and Norton
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 10 / 13
Any complicated linear circuit with two terminals is exactly equivalent toeither of two simpler circuits with only two components. Any measurementwill give the same result on any of the three circuits.
Original
![Page 51: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/51.jpg)
Thévenin and Norton
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 10 / 13
Any complicated linear circuit with two terminals is exactly equivalent toeither of two simpler circuits with only two components. Any measurementwill give the same result on any of the three circuits.
Original Thévenin
![Page 52: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/52.jpg)
Thévenin and Norton
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 10 / 13
Any complicated linear circuit with two terminals is exactly equivalent toeither of two simpler circuits with only two components. Any measurementwill give the same result on any of the three circuits.
Original Thévenin Norton
![Page 53: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/53.jpg)
Thévenin and Norton
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 10 / 13
Any complicated linear circuit with two terminals is exactly equivalent toeither of two simpler circuits with only two components. Any measurementwill give the same result on any of the three circuits.
Original Thévenin Norton
Common measurements are:
![Page 54: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/54.jpg)
Thévenin and Norton
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 10 / 13
Any complicated linear circuit with two terminals is exactly equivalent toeither of two simpler circuits with only two components. Any measurementwill give the same result on any of the three circuits.
Original Thévenin Norton
Common measurements are:
• Thévenin Resistance, RTh: Resistance between the terminals whenall sources are set to zero (same for Thévenin and Norton).
![Page 55: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/55.jpg)
Thévenin and Norton
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 10 / 13
Any complicated linear circuit with two terminals is exactly equivalent toeither of two simpler circuits with only two components. Any measurementwill give the same result on any of the three circuits.
Original Thévenin Norton
Common measurements are:
• Thévenin Resistance, RTh: Resistance between the terminals whenall sources are set to zero (same for Thévenin and Norton).
• Open circuit voltage (= voltage when drawing zero current from theterminals): = VTh = INoRTh.
![Page 56: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/56.jpg)
Thévenin and Norton
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 10 / 13
Any complicated linear circuit with two terminals is exactly equivalent toeither of two simpler circuits with only two components. Any measurementwill give the same result on any of the three circuits.
Original Thévenin Norton
Common measurements are:
• Thévenin Resistance, RTh: Resistance between the terminals whenall sources are set to zero (same for Thévenin and Norton).
• Open circuit voltage (= voltage when drawing zero current from theterminals): = VTh = INoRTh.
• Short circuit current: = INo = VTh
RTh
.
![Page 57: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/57.jpg)
Op Amps
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 11 / 13
• Ideal Op Amp: (a) Zero input current, (b) Infinite gain(b) ⇒ V+ = V− provided the circuit has negative feedback.
• Negative Feedback: An increase in Vout causes(V+ − V−) to decrease.
![Page 58: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/58.jpg)
Op Amps
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 11 / 13
• Ideal Op Amp: (a) Zero input current, (b) Infinite gain(b) ⇒ V+ = V− provided the circuit has negative feedback.
• Negative Feedback: An increase in Vout causes(V+ − V−) to decrease.
Non-inverting amplifier
Y =(1 + 3
1
)X
![Page 59: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/59.jpg)
Op Amps
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 11 / 13
• Ideal Op Amp: (a) Zero input current, (b) Infinite gain(b) ⇒ V+ = V− provided the circuit has negative feedback.
• Negative Feedback: An increase in Vout causes(V+ − V−) to decrease.
Non-inverting amplifier
Y =(1 + 3
1
)X
Inverting amplifier
Y = −81 X1 +
−82 X2 +
−82 X3
![Page 60: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/60.jpg)
Block Diagrams
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 12 / 13
Blocks are labelled with their gains and connected using adder/subtractorsshown as circles. Adder inputs are marked + for add or − for subtract.
![Page 61: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/61.jpg)
Block Diagrams
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 12 / 13
Blocks are labelled with their gains and connected using adder/subtractorsshown as circles. Adder inputs are marked + for add or − for subtract.
To analyse:
1. Label the inputs, the outputs and the output of each adder.
![Page 62: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/62.jpg)
Block Diagrams
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 12 / 13
Blocks are labelled with their gains and connected using adder/subtractorsshown as circles. Adder inputs are marked + for add or − for subtract.
To analyse:
1. Label the inputs, the outputs and the output of each adder.
2. Write down an equation for each variable:
• U = X − FGU
• Follow signals back though the blocks until you meet a labelled node.
![Page 63: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/63.jpg)
Block Diagrams
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 12 / 13
Blocks are labelled with their gains and connected using adder/subtractorsshown as circles. Adder inputs are marked + for add or − for subtract.
To analyse:
1. Label the inputs, the outputs and the output of each adder.
2. Write down an equation for each variable:
• U = X − FGU , Y = FU + FGHU
• Follow signals back though the blocks until you meet a labelled node.
![Page 64: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/64.jpg)
Block Diagrams
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 12 / 13
Blocks are labelled with their gains and connected using adder/subtractorsshown as circles. Adder inputs are marked + for add or − for subtract.
To analyse:
1. Label the inputs, the outputs and the output of each adder.
2. Write down an equation for each variable:
• U = X − FGU , Y = FU + FGHU
• Follow signals back though the blocks until you meet a labelled node.
3. Solve the equations (eliminate intermediate node variables):
• U(1 + FG) = X
![Page 65: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/65.jpg)
Block Diagrams
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 12 / 13
Blocks are labelled with their gains and connected using adder/subtractorsshown as circles. Adder inputs are marked + for add or − for subtract.
To analyse:
1. Label the inputs, the outputs and the output of each adder.
2. Write down an equation for each variable:
• U = X − FGU , Y = FU + FGHU
• Follow signals back though the blocks until you meet a labelled node.
3. Solve the equations (eliminate intermediate node variables):
• U(1 + FG) = X ⇒ U = X1+FG
![Page 66: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/66.jpg)
Block Diagrams
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 12 / 13
Blocks are labelled with their gains and connected using adder/subtractorsshown as circles. Adder inputs are marked + for add or − for subtract.
To analyse:
1. Label the inputs, the outputs and the output of each adder.
2. Write down an equation for each variable:
• U = X − FGU , Y = FU + FGHU
• Follow signals back though the blocks until you meet a labelled node.
3. Solve the equations (eliminate intermediate node variables):
• U(1 + FG) = X ⇒ U = X1+FG
• Y = (1 +GH)FU
![Page 67: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/67.jpg)
Block Diagrams
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 12 / 13
Blocks are labelled with their gains and connected using adder/subtractorsshown as circles. Adder inputs are marked + for add or − for subtract.
To analyse:
1. Label the inputs, the outputs and the output of each adder.
2. Write down an equation for each variable:
• U = X − FGU , Y = FU + FGHU
• Follow signals back though the blocks until you meet a labelled node.
3. Solve the equations (eliminate intermediate node variables):
• U(1 + FG) = X ⇒ U = X1+FG
• Y = (1 +GH)FU= (1+GH)F1+FG
X
![Page 68: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/68.jpg)
Block Diagrams
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 12 / 13
Blocks are labelled with their gains and connected using adder/subtractorsshown as circles. Adder inputs are marked + for add or − for subtract.
To analyse:
1. Label the inputs, the outputs and the output of each adder.
2. Write down an equation for each variable:
• U = X − FGU , Y = FU + FGHU
• Follow signals back though the blocks until you meet a labelled node.
3. Solve the equations (eliminate intermediate node variables):
• U(1 + FG) = X ⇒ U = X1+FG
• Y = (1 +GH)FU= (1+GH)F1+FG
X
[Note: “Wires” carry information not current: KCL not valid]
![Page 69: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/69.jpg)
Diodes
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 13 / 13
Each diode in a circuit is in one of two modes; each has an equalitycondition and an inequality condition:
• Off: ID = 0, VD < 0.7
• On: VD = 0.7, ID > 0
(a) Guess the mode(b) Do nodal analysis assuming the equality condition(c) Check the inequality condition. If the inequality condition fails, you
made the wrong guess.
![Page 70: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/70.jpg)
Diodes
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 13 / 13
Each diode in a circuit is in one of two modes; each has an equalitycondition and an inequality condition:
• Off: ID = 0, VD < 0.7
• On: VD = 0.7, ID > 0
(a) Guess the mode(b) Do nodal analysis assuming the equality condition(c) Check the inequality condition. If the inequality condition fails, you
made the wrong guess.
• Assume Diode Off
X = 5 + 2 = 7
![Page 71: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/71.jpg)
Diodes
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 13 / 13
Each diode in a circuit is in one of two modes; each has an equalitycondition and an inequality condition:
• Off: ID = 0, VD < 0.7
• On: VD = 0.7, ID > 0
(a) Guess the mode(b) Do nodal analysis assuming the equality condition(c) Check the inequality condition. If the inequality condition fails, you
made the wrong guess.
• Assume Diode Off
X = 5 + 2 = 7VD = 2
![Page 72: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/72.jpg)
Diodes
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 13 / 13
Each diode in a circuit is in one of two modes; each has an equalitycondition and an inequality condition:
• Off: ID = 0, VD < 0.7
• On: VD = 0.7, ID > 0
(a) Guess the mode(b) Do nodal analysis assuming the equality condition(c) Check the inequality condition. If the inequality condition fails, you
made the wrong guess.
• Assume Diode Off
X = 5 + 2 = 7VD = 2 Fail: VD > 0.7
![Page 73: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/73.jpg)
Diodes
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 13 / 13
Each diode in a circuit is in one of two modes; each has an equalitycondition and an inequality condition:
• Off: ID = 0, VD < 0.7
• On: VD = 0.7, ID > 0
(a) Guess the mode(b) Do nodal analysis assuming the equality condition(c) Check the inequality condition. If the inequality condition fails, you
made the wrong guess.
• Assume Diode Off
X = 5 + 2 = 7VD = 2 Fail: VD > 0.7
• Assume Diode On
X = 5 + 0.7 = 5.7
![Page 74: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/74.jpg)
Diodes
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 13 / 13
Each diode in a circuit is in one of two modes; each has an equalitycondition and an inequality condition:
• Off: ID = 0, VD < 0.7
• On: VD = 0.7, ID > 0
(a) Guess the mode(b) Do nodal analysis assuming the equality condition(c) Check the inequality condition. If the inequality condition fails, you
made the wrong guess.
• Assume Diode Off
X = 5 + 2 = 7VD = 2 Fail: VD > 0.7
• Assume Diode On
X = 5 + 0.7 = 5.7
ID + 0.71 k = 2mA
![Page 75: RevisionLecture1: Nodal Analysis](https://reader031.vdocuments.us/reader031/viewer/2022020703/61fb3cd82e268c58cd5bcb60/html5/thumbnails/75.jpg)
Diodes
RevisionLecture 1: NodalAnalysis
• Exam
• Basic Concepts
• Ohm’s Law
• Nodal Analysis
• Nodal Analysis Example
• Voltage and CurrentDividers
• Superposition
• Superposition Example
• Thévenin and Norton
• Op Amps
• Block Diagrams
• Diodes
E1.1 Analysis of Circuits (2014-4530) Revision Lecture 1 – 13 / 13
Each diode in a circuit is in one of two modes; each has an equalitycondition and an inequality condition:
• Off: ID = 0, VD < 0.7
• On: VD = 0.7, ID > 0
(a) Guess the mode(b) Do nodal analysis assuming the equality condition(c) Check the inequality condition. If the inequality condition fails, you
made the wrong guess.
• Assume Diode Off
X = 5 + 2 = 7VD = 2 Fail: VD > 0.7
• Assume Diode On
X = 5 + 0.7 = 5.7
ID + 0.71 k = 2mA OK: ID > 0