review for final monday 5/6, 3:00-6:00pm sage 4101
Post on 21-Dec-2015
217 views
TRANSCRIPT
Review for Final
Monday 5/6, 3:00-6:00pm
Sage 4101
How is Light Better?
• FASTER – nothing can travel faster than light in vacuum– Extremely high bandwidth
• COOLER (transfer, not nec. processing)– Less loss from scattering as light travels through fibers
than electrons through wires
• FOURIER TRANSFORMS (clever parallel processing)– Light traveling through a lens performs a Fourier
transform automatically
Fabry-Perot Interferometer• Ends of cavity like open ends of string: wave not
inverted when it is reflected• Standing wave set up if cavity length integer
number of half-wavelengths• Can’t just change frequency, since that affects
other devices too
More Fabry-Perot Interferometer
• Index of refraction determines wavelength• Intensity affects index of refraction• If intensity inside cavity high enough, wavelength
will change - from destructive to constructive• This is a resonant process - a large effect occurs
very quickly • Can amplify a signal by keeping a constant
intensity near the critical value
Advantages of FP
• MULTI-FUNCTION - same device can be– AND – low constant signal – need both inputs
to produce resonance– OR – medium constant signal - either input
strong enough to produce resonance– Amplifier – medium constant signal – small
input leads to resonance
Why Aren’t Fabry Perot Devices Front Page Now?
• High intensity used to change n also produces heat - materials (usually) expand when heated - throws off interference effect
• Can switch on faster than off• Need wide bandgap to operate at room T• BIG!!!
Another Option: Excitons
• Hole and electron are attracted, lowering energy in a bound state
• Photons emitted when hole and electron pair (exciton) combine has therefore slightly less energy than when hole and electron are not bound
• Can maximize this effect by forcing electron and hole into close proximity (quantum well)
• Applying a voltage means energies are closer together, but might break bond
• Can minimize bond breaking by quantum well
SEEDs
• Self-Electro-optic Effect Device (uses feedback)• Set stage:
– Shine light of exciton energy on quantum well in middle of p-n junction
– Light is absorbed and produces excitons– Apply reverse bias which slightly separates excitons
but “significantly” lowers the energy and reduces absorption
• If light intensity is increased, absorption increases slightly – can produce more excitons and raise their energy– brings energy back to absorption peak
Pros and Cons of SEEDs• Needs only low power (FP needs high
power)
• Easier to manufacture – don’t need fine-tuned cavity length
• Lower operating speed than FP
Problems with Optical Computers
• Using only part-optical computers (i.e., interconnects) requires adapters
• Much research already in semiconductors - hard for light to beat that– Light doesn’t interact because it’s not charged
First Exam
What have we learned?• Any traveling sinusoidal wave may be described by
y = ym sin(kx t + )
• Light always reflects with an angle of reflection equal to the angle of incidence (angles are measured to the normal).
• When light travels into a denser medium from a rarer medium, it slows down and bends toward the normal.
• The Fourier spectrum of a wider pulse will be narrower than that of a narrow pulse, so it has a smaller bandwidth.
• Your bandwidth B must be as large as the rate N at which you transfer different amplitudes.
• The rise time of each pulse must be no more than 70% of the duration of the pulse
Review (cont.)• Any periodic function of frequency f0 can be expressed as a
sum over frequency of sinusoidal waves having frequencies equal to nf0, where n is an integer. The sum is called the
Fourier series of the function, and a plot of amplitude (coefficient of each sin/cos term) vs. frequency is called the Fourier spectrum of the function.
• Any non-periodic function (so frequency f0 0) can be
expressed as an integral over frequency of sinusoidal waves having frequencies. The integral is called the Fourier transform of the function, and a plot of amplitude vs. frequency is called the Fourier spectrum of the function.
• The Fourier spectrum of a wider pulse will be narrower than that of a narrow pulse, so it has a smaller bandwidth.
What Else Have We Learned?
• Can represent binary data with pulses in a variety of ways
• 10110 could look like . . .
Non-return-to-zero (NRZ)
Return-to-zero (RZ)
Bipolar Coding
Notice that the NRZ takes half the time of the others for the same pulse widths
Other schemes use tricks to reduce errors and BW requirements.
Optical Waveguides Summary• Dispersion means spreading
• Signals in a fiber will have several sources of dispersion:– Chromatic:
• Material: index of refraction depends on wavelength (prism)
• Waveguide: some of wave travels through cladding with different index of refraction (primarily single-mode) – leads to wavelength-dependent effects
– Modal: different modes travel different paths and so require different amounts of time to travel down fiber (CUPS)
• Also have attenuation/loss due to scattering/absorption by fiber material, which depends on wavelength/frequency
Optical Waveguide Summary (cont.)
• Modes in a fiber are specific field distributions that are independent of “z”, or length traveled down the fiber
• Fields of modes look like harmonics of standing waves
• Can make a single-mode fiber by:– reducing diameter of fiber so smaller cone of
light enters– reducing NA of fiber so smaller cone of light is
trapped
Interference of Waves
If crests match crests, then waves interfere constructively
Crests will match if waves are one wavelength, two wavelengths, … apart: path difference = m
Amax
2Amax
wave 1
wave 2
sum
Amax
Destructive Interference
If crests match troughs (180° out of phase), then waves interfere destructively
Crests will match troughs if waves are one/half wavelength, three/half wavelengths, … apart: path difference = (m+½)
wave 1
wave 2
sum
Amax
Amax
What This Means for Light
Light is electromagnetic radiation A light wave is oscillating electric and magnetic
fields The amplitude of the oscillation represents the
maximum electric (or magnetic) field and determines the intensity of light
Intensity depends on the square of the maximum electric field: I = Emax
2/(2c0) Constructive interference produces brighter light;
destructive interference produces dimmer light.
Comparing Interference
Emax
2Emax
Medium amplitude of electric field yields medium intensity light
Double amplitude of electric field yields quadruple intensity (very bright) light
Zero amplitude of electric field yields zero intensity (no) light
Coherent vs. Incoherent Light
• “Everyday light” is incoherent
• Laser light is an example of coherent light
• Simple wave equation describes coherent waves
y = ym sin(kx t + )
Diffraction Math
The locations of successive minima are given by
tan = y/D
for small angles, sin ~ ~ tan = y/D
.....)3 ,2 ,1(sin
,...)2 ,1 ,0( 2
1sin
2
nna
mma
Diffraction by a circular aperture A circular aperture of diameter d
Single slit of width a
minimum)(1st 22.1sind
minimum)(1st sina
Resolvability
Two objects are just resolved when the central diffraction maximum of one object is at the first minimum of the other. (Rayleigh’s criterion)
As before, approximately y/L
ddR
22.122.1
sin 1
Comments on Resolvability
If want to resolve objects closer to each other (smaller y), need smaller wavelength of light or larger aperature
This is called the diffraction limit
dD
yR
22.1
2nd Exam
Charges in Conductors
Electric fields are created when positive charges and negative charges are separated
A uniform electric field existing over a region sets up a potential difference between points in that region: V=Ex, where x is the distance along a field line.
If I apply a potential difference across a conducting object (including semiconductors), charges experience a force, and charge carriers will flow until the potential difference is removed.
What Have We Learned About Electrical Storage
• The electric force FE on a charge q0 can be considered due to an electric field which is produced by other charges in the area
FE = q0 E• If moving a charge between two points requires work (or does
work), the charge gains (or loses) potential energy:V = – E dx = (for a constant field) Ex
• Capacitors store charge Q in proportion to the voltage V between the plates:
C = Q/V = C = 0 A/d• Capacitors are used in RAM
What Have We Learned About Magnetic Storage?
• Two domains magnetized in same direction is a 0• Two domains magnetized in opposite directions is
a 1• Direction of magnetization changes at start of new
bit.• Magnetic data is written by running a current
through a loop of wire near the disk• As magnetic data passes by coil of wire, changing
field induces currents according to Faraday’s Law:
dt
dBA
dt
diR B
What Have We Learned About Magnetoresistance?
• Charges traveling through magnetic field experience magnetic force (provided velocity and field are not aligned):
FB = qv x B = (if v perpendicular to B) qvB• In a current-carrying wire, this force results in more
frequent collisions and thus an increased resistance: Magnetoresistance
• Electrons traveling through magnetized material undergo spin-dependent scattering
• When magnetic field is present in magnetic superlattice, scattering of electrons is cut dramatically, greatly decreasing resistance: Giant magnetoresistanced
Stuff to remember about GMR
• Electrons (and other elementary “particles”) have intrinsic magnetic fields, identified by spin
• The scattering of electrons in a ferromagnetic material depends on the spin of the electrons
• Layers of ferromagnetic material with alternating directions of magnetization exhibit maximum resistance
• In presence of magnetic field, all layers align and resistance is minimized
What Have We Learned About Spectra?
• ENERGY LEVELS ARE QUANTIZED
• Different elements have different allowed energies (since different numbers of protons and electrons provide different structure of attraction
• Light emitted when electrons move from a high energy level to a lower energy level in an atom will have only certain, QUANTIZED, allowed energies and wavelengths.
• Those wavelengths depend solely on the element emitting the light and compose the characteristic emission spectrum for that element
Our Model of the Atom
• If the atom is in the “ground state” of lowest energy, electrons fill the states in the lowest available energy levels. The first shell has two possible states, and the second shell has eight possible states. Higher shells have more states, but we’ll represent them with the eight states in the first two sub-shells.
• Electrons in the outermost shell are called “valence” electrons. We’ll
make them green to distinguish from e- in filled shells
E=0 (unbound)
n=1
n=2n=3n=4
Really eight distinct states with closely spaced energies, since two electrons cannot occupy the same state.
Electrons in Solids• The shifted energies in adjacent atoms combine to create a continuous
“band” of allowed energies for each original energy level; each band, however, has a finite number of states equal to the number in original atoms
• Electrons can move from the locality of one atom to the next only if an energy state is available within the same band
Conductors & Semiconductors
• In conductors, the valence band is only partially-full, so electrons can easily move from being near one atom to being near another
• In semiconductors and insulators, the valence band is completely full, so electrons must gain extra energy to move
• In semiconductors, extra electrons (or holes) can be introduced in a “controlled” way.
What Have We Learned About Solids?
• In conductors, the valence band is only partially-full, so electrons can easily move
• In semiconductors and insulators, the valence band is completely full, so electrons must gain extra energy to move– semiconductors have smaller band gap, insulators have larger band
gap
• Conductors have a partially-filled valence band– The primary effect of higher temperature on resistance is to increase
R due to more collisions at higher temperatures
• Semiconductors have a completely-filled valence band– The primary effect of temperature on resistance is due to this
requirement: the higher the temperature, the more conduction electrons
What have we learned about Resistance?
• In many, ohmic, materials, current is proportional to voltage:
V = iR• Resistance is proportional to the length of an
object and inversely proportional to cross-sectional area:
R = L/A• The constant of proportionality here is called the
resistivity. It is a function of material and temperature.
R
EL
R
VAnevi d
m
eEvd
Lm
AneR
2
/1
p-n junction
n-type
p-type
Energy
depleted region(electric field)
+ + + + + ++
+
--------
Vo
Biased junction
n-type
p-type
depleted region(electric field)
Negativebias
photon out
How does a semiconductor laser work?
Stimulated vs. Spontaneous Emission (Cont.)
Derived in 1917 by Einstein. (Required for thermal equilibrium was it was recognized that photons were quantized.)
However, a “real” understanding of this was not achieved until the 1950’s.
MOSFET
• The potential difference between drain and source is continually applied
• When the gate potential difference is applied, current flows
Source Drain
n-type p-typen-type
Gate
(Metal-Oxide-Semiconductor, Field-Effect Transistor)
Bipolar Junction Transistor
n-type p-type n-type
Emitter BaseCollector
increasing electron energy
increasing hole energy
Bipolar Junction Transistor
http://hyperphysics.phy-astr.gsu.edu/hbase/solids/trans.html#c1
AND - slightly more complicated
AND gate returns a signal only if both of its two inputs are on.
Use the NAND output as input for NOT
If both inputs are on, the NOT input is off, so the AND output is on.
Else the NOT input is on, so the output is off.
Dump
Input Input
Switch Switch
Switch
Output
Wide Bandgap SemiconductorsWhat is a wide bandgap semiconductor?
Larger energy gap allows higher power and temperature operation and the generation of more energetic (i.e. blue) photons
The III-nitrides (AlN, GaN and InN), SiC have recently become feasible. Other materials (like diamond) are being investigated.
What are they good for?
Pictorial Representation of 3D Integration Conceptusing Wafer Bonding,
* Figure adapted from IBM Corporation and used with permission.
Via Plug
Second Level(Thinned Substrate)
First Level
Third Level(Thinned Substrate)
Via Bridge
Bond
DeviceSurface
DeviceSurface
Bond(Face-to-face)
(Face-to-back)
DeviceSurface
Substrate
Substrate
Substrate
J. Lu et al
Broad band interconnect technology---high speed data transfer
Replacing electrical connection by optics:•Modulators/switches: electro-optic, optic-optic•Optical waveguides•Data compression (software)
Modulators guide
Chip stack
switches
fiber
Or: wireless!
light
Oriented & interconnected nanotube networks—Ajayan et al
– Local modification and Junction formation
– Termination (cutting of structures)
Catalyst
Junctions
Focused Ions
Einstein to the Rescue
• Einstein suggested that light was emitted or absorbed in particle-like quanta, called photons, of energy, E = hf
cresttrough
If an electron absorbs one of these photons, it gets the entire hf of energy.
If that energy is larger than the work function of the metal, the electron can leave; if not, it can’t:
Kmax = Eabs – = hf -
Particle in a box(x) = B sin (nx/a)
(x) |(x)|2n=2
n=3
Only certain wavelengths = 2a/n are allowedOnly certain momenta p = h/ = hn/2a are allowedOnly certain energies E = p2/2m = h2n2/8ma2 are
allowed - energy is QUANTIZEDAllowed energies depend on well width
“Real-World” Wells• Solution has non-trivial form, but only certain
states (integer n) are solutions• Each state has one allowed energy, so energy is
again quantized• Energy depends on well width a (confinement
width)
|(x)|2
n=1n=2
x
Escaping quantum wells• Thanks to quantum mechanics, an electron has a non-zero
probability of appearing outside of the well• This happens much more often than thermal escape if the
wells are close together.
A tunnel diode
• According to quantum physics, electrons could tunnel through to holes on the other side of the junction with comparable energy to the electron
• This happens fairly often• Applying a bias moves the
electrons out of the p-sideso more can tunnel in
The tunneling transistor
• As the potential difference increases, the energy levels on the positive side are lowered toward the electron’s energy
• Once the energy state in the well equals the electron’s energy, the electron can go through, and the current increases.
The tunneling transistor
• The current through the transistor increases as each successive energy level reaches the electron’s energy, then decreases as the energy level sinks below the electron’s energy
Quantum Entanglement(Quantum Computing)
• Consider photons going through beam splitters• NO way to predict whether photon will be
reflected or transmitted!
(Color of line is NOT related to actual color of laser; all beams have same wavelength!)
Adding amplitudes
• Lower detector:
• Upper detector:
TT22
1RR
22
1RT
2
1TR
2
1 ii
02
1
2
12
2
122
22
22
1
22
122
2
iii