rev 13 p/n 5004wp part's manual -...

© 2008 Alamo Group Inc.

®

®

PART'S MANUAL

1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4261

MODEL 1700, 2200, 2200F & 2500Rev 08-13 P/N 5004WP

An Operator's Manual was shipped with the equipment in theManual Canister. This Operator's Manual is an integral part ofthe safe operation of this machine and must be maintainedwith the unit at all times. READ, UNDERSTAND, and FOLLOWthe Safety and Operation Instructions contained in this manualbefore operating the equipment. If the Operator's Manual isnot with the equipment, contact your dealer or M&W(800-446-5158) to obtain a Free copy before operating theequipment.

TO THE OWNER/OPERATOR/DEALERAll implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator whorecognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement tobe used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Formin full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Cardand on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophicfailure with possible injury or death.

PARTSSECTION

Parts Section – 1

Parts Section – 2©2008 Alamo Group Inc.

PARTS ORDERING GUIDE

For maximum safety and to guarantee optimum product reliability, always usegenuine Alamo Group Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death. Directany questions regarding parts to:

The following instructions are offered to help eliminate needless delay and error in processingpurchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basicmachine featured in this manual. Part Numbers and Descriptions are given to help locate the partsand quantities required.

2. The Purchase Order must include the name and address of the person or organization orderingthe parts, who should be charged, and if possible, the serial number of the machine for which theparts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct partnumber, and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and aresubject to special handling. Request a quotation for such parts before sending a Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

NOTE: Please refer to The Safety Section in the front of this Manual for the proper PartNumber when ordering Replacement Safety Decals.

M&W1020 South Sangamon Ave.Gibson City, Illinois 60936217-784-4561

PART NAME INDEX

COIL TINE LEVELER WING CYLINDER (OPTIONAL) ....................................................................................................... 37COIL TINE LEVELER 1700 (OPTIONAL) S/N 10077 -CURRENT Rev 09-04 .................................................................... 33COIL TINE LEVELER 2500 2200 2200F S/N -CURRENT (OPTIONAL)............................................................................. 35DISC FRAME 1700 & 2200.................................................................................................................................................... 6DISC GANG Rev 11-04........................................................................................................................................................ 16DISC LIFT CYLINDER.......................................................................................................................................................... 26DISC WING LIFT CYLINDER............................................................................................................................................... 29FOLDING DISC FRAME COMPONENTS 2200F & 2500 Rev 09-04.................................................................................... 8FOLDING WING COMPONENTS 2200F & 2500 Rev 09-04 .............................................................................................. 12FRONT MAINFRAME ........................................................................................................................................................... 18HOSE SCHEMATIC.............................................................................................................................................................. 24HOSE SCHEMATIC FOLDING WING.................................................................................................................................. 25HOSE SCHEMATIC OPTIONAL .......................................................................................................................................... 38HUB & SPINDLE .................................................................................................................................................................. 21LIGHT KIT PARTS................................................................................................................................................................ 22MAIN AXLE LIFT CYLINDER............................................................................................................................................... 28REAR MAINFRAME Rev 01-07 ........................................................................................................................................... 10RELIEF VALVE...................................................................................................................................................................... 31 SEQUENCE VALVE ............................................................................................................................................................. 30SHANK Rev 11-04................................................................................................................................................................ 14SUPER LINK ASSEMBLY .................................................................................................................................................... 32TONGUE CYLINDER ........................................................................................................................................................... 27TONGUE PARTS.................................................................................................................................................................... 4TRUNNION ASSEMBLY 1 ................................................................................................................................................... 19TRUNNION ASSEMBLY 2 ................................................................................................................................................... 20

EARTHMASTER 1700 - 2500 (Sept-08) -Current Rev 09-08 ©2008 Alamo Group Inc. Parts Section – 3

TONGUE PARTS

EARTHMASTER 1700 - 2500 (Sept-08) -Current Rev 09-08

©2008 Alamo Group Inc. Parts Section – 4

TONGUE PARTS

ITEM PART NO. QTY. DESCRIPTION

1 00000200 2 NUT, 3/4" NC2 00001800 3 LOCKNUT, 1/2" NC3 00015800 2 NUT, 3/4" NC TOPLOCK4 00037100 2 HEX BOLT, 3/4" NC X 2-1/2" PL55 00725712 1 PIN, PULL BENT6 00748823 3 BOLT, 1/2" NC X 1-1/2" PL57 00749185 2 FLATWASHER, 1-1/4" 9 00773592 6 PIN, SAFETY LOCK LYNCH10 02962213 2 ADAPTER, HYDRAULIC ELBOW11 15B1200 2 WASHER, 3/4"12 165020 1 PIN, COTTER13 2450129 1 ASSEMBLY, TOP LINK14 2457104 1 CYLINDER, HYDRAULIC15 2460244 1 WELDMENT, HITCH PIN16 2460340 1 WELDMENT, JACK MOUNT17 2460248 1 WELDMENT, FRONT MAINFRAME18 2460249 1 WELDMENT, TONGUE19 2460255 2 WELDMENT, PIN SUPER LINK LOWER20 2460257 2 WELDMENT, TONGUE PIN21 2460317 1 WELDMENT, TOPLINK ARM22 2460318 1 WELDMENT, UPPER CYLINDER PIN23 2460319 1 WELDMENT, TOP LINK PIN24 2461153 2 CLAMP, HOSE25 2461603 1 PLATE, HOSE RETAINER26 2465500 1 CASTINGS, CLEVIS HITCH27 2466250 1 CHAIN, SAFETY TOW28 2468613 1 JACK29 2471001 1 STOP30 330812C 1 HEX NUT, SLOTTED, 1-1/4" X 7 PL531 35009C 2 LOCKWASHER, 3/4"



8 63092200 2 HEX 5/16" NC 3-1/2 PL5

32 2468410 2 PLATE,SINGLE COVER TOP33 2468408 2 CLAMP, 14MM TUBE HALF34 2468409 2 CLAMP, 20MM TUBE HALF

DISC FRAME 1700 & 2200



DISC FRAME 1700 & 2200

ITEM PART NO. 1700 2200 DESCRIPTION

1 00015800 4 4 LOCKNUT, 3/8" NC2 00695100 24 24 LOCKNUT5/8" NC3 00696800 1 1 ADAPTER, HYDRAULIC STRAIGHT4 00753642 4 4 BOLT, 3/8" NC X 1-1/4" PL55 00753753 24 24 HEXBOLT, 5/6" NC x 2 PL86 00773592 4 4 PIN, SAFETY LOCK LYNCH7 02032200 8 8 LOCKWASHER, 1"8 02782200 8 8 BOLT, 1 NC x 2 PL89 02962213 1 1 ADAPTER, HYDRAULIC ELBOW10 2457103 1 1 CYLINDER, HYDRAULIC11 2460212 2 - FRONT GANG TUBE WELDMENT12 2460213 2 - WELDMENT, REAR GANG TUBE13 2460214 - 2 WELDMENT, FRONG GANG TUBE14 2460215 - 2 WELDMENT, REAR GANG TUBE15 2460241 2 - WELDMENT, OUTER DISC FRAME16 2460242 - 2 WELDMENT, OUTER DISC FRAME17 2460243 1 1 WELDMENT, MAIN DISC FRAME18 2460253 1 1 WELDMENT, LIFT CROSSTUBE FRONT19 2460254 2 2 WELDMENT, LIFT TIE ROD20 2460263 4 4 WELDMENT, DISC GANG PIN21 2460284 10 10 WELDMENT, DISC LIFT PIN22 2460285 1 1 WELDMENT, LIFT CROSSTUBE REAR23 2460306 4 4 WELDMENT, DISC GANG PIVOT PIN24 2462600 8 8 BLOCK, ANTI ROTATE25 380010C 10 10 FLATWASHER26 49045 10 10 COTTER PIN27 2461622 4 4 SPACER,DISC GANG PIN



FOLDING DISC FRAME COMPONENTS 2200F & 2500 Rev 09-04



FOLDING DISC FRAME COMPONENTS 2200F & 2500 Rev 09-04

ITEM PART NO. QTY. QTY. DESCRIPTION

¤ 2200F 25001 2460327 1 - WDMT,LH OUTER DISC WING

2460299 - 1 WDMT,LH OUTER DISC WING2 2460305 2 2 WDMT,INNER DISC WING3 2460320 2 - WDMT,FRONT GANG TUBE

2460300 - 4 WDMT,FRONT GANG TUBE4 2460323 2 - WDMT,REAR INNER GANG TUBE

2460302 - 2 WDMT,INNER REAR GANG TUBE5 2460321 2 - WDMT,REAR GANG TUBE6 2460322 2 - WDMT,FRONT INNER GANG TUBE

2460301 - 2 WDMT,INNER FRONT GANG TUBE7 2460330 2 2 WDMT,LH WING LIFT LINK8 1937156 4 4 SPEC. 90DG ELBOW W/RESTRICTOR9 2467105 2 2 CYLINDER,HYDRAULIC 3-1/2 X 1010 2460263 8 8 WDMT,DISC GANG PIN11 2471038 2 2 PLATE,LIFT LINK12 2462534 6 6 PIN,SHORT DISC WING PIVOT13 2462535 6 6 PIN,DISC WING PIVOT14 2462532 2 2 PIN,CYLINDER CLEVIS15 2460306 8 8 WDMT,DISC GANG PIVOT PIN16 2462600 16 16 BLOCK,ANTI-ROTATE17 00773592 8 8 PIN, SAFETY LOCK LYNCH18 2460329 2 2 WDMT,RH WING LIFT LINK19 00015800 8 8 NUT,TOPLOCK 3/8NC PLB20 00695100 24 24 NUT,TOPLOCK 5/8 NC PLB21 00753642 8 8 HHCS,3/8NC X 1-1/4,ZP,GRD522 00753753 24 24 HEXB 5/8 NC 2 PL 823 02032200 16 16 LOCKWASHER 1 STD24 31793H8C 16 16 HEXB 1 NC 2 PL825 2460326 1 - WDMT,RH OUTER DISC WING

2460298 - 1 WDMT,RH OUTER DISC WING26 15B2000 12 12 WASHER SAE 1 1/4 PLATED27 00606000 14 14 PIN-COTTER 3/16 X 228 15B1600 2 2 WASHER 1 SAE P29 2461622 8 8 SPACER,DISC GANG TUBE



30 10070000 8 8 BOLT, 1/4" NC x 2-1/2" P31 02959924 8 8 NUT, 1/4" NC

REAR MAINFRAME Rev 01-07



REAR MAINFRAME Rev 01-07


2 00037200 24 LOCKNUT, 3/4" NC3 00725712 2 PIN, PULL BENT4 00749185 8 WASHER1-1/4"5 02918600 8 HEXBOLT, 3/4" NC X 2 PL86 02962213 4 ADAPTER, HYDRAULIC ELBOW7 02963646 16 BOLT, 3/4" NC X 2-1/2" PL58 02969064 2 BUSHING, SPRING9 0536800W 8 SEAL10 2460102 4 ASSEMBLY, HUB & SPINDLE (SEE PG 21 FOR BREAKDOWN)12 2460328 2 WELDMENT, WHEEL STRUT13 2460229 2 WELDMENT, TRUNNION14 2460238 1 WELDMENT, AXLE TORSION15 2460239 1 WELDMENT, REAR MAINFRAME16 2460261 2 WELDMENT, 1700 WING17 2460262 2 WELDMENT, 2200 WING18 2462500 4 PIN19 2462510 2 PIN, DEPTH STOP20 2466000 8 BEARING, GARIOCK21 2466777 4 SHIELD22 2467102 2 CYLINDER, HYDRAULIC23 2467600 4 WHEEL (1700, 2200)

2467601 4 WHEEL, (2500, 2200F)24 2467801 4 TIRE25 2471002 2 STOP26 314017H5C 12 BOLT, 1/2" NC X 4 PL527 32905C 12 NUT, 1/2" NC28 49208 2 COTTER, HAIRPIN29 TR415 4 VALVE STEM30 2460136 4 COMPLETE TIRE AND WHEEL ASSY. (1700, 2200)

2460150 4 COMPLETE TIRE AND WHEEL ASSY. (2500, 2200F)31 2461160 8 CLAMP,SHIELD BACK-UP32 02959924 8 NUT TOPLOCK 1/4 NC PL833 00021400 8 HEXB 1/4 NC X 3/4 PL534 4720 4 GREASE FITTING 1/8 SELF TAP



FOLDING WING COMPONENTS 2200F & 2500 Rev 09-08



EARTHMASTER 1700 - 2500 (Sept-08) -Current Rev 09-08©2008 Alamo Group Inc. Parts Section – 13

FOLDING WING COMPONENTS 2200F & 2500 Rev 09-04

ITEM PART NO. QTY. QTY. DESCRIPTION ¤ 2200F 2500

1 2460297 1 1 WDMT,LH SHORT V-WING 2 2460325 1 - WDMT,LH FOLDING V-WING * 2460287 - 1 WDMT,LH V-WING * 2460296 1 1 WDMT,RH SHORT V-WING (NOT SHOWN) * 2460324 1 - WDMT,RH FOLDING V-WING (NOT SHOWN) * 2460286 - 1 WDMT,RH V-WING (NOT SHOWN) 3 317024H5C 4 4 HEX CAP 3/4-10 X 10 GR.5 4 2460260 2 2 WDMT,MID MOUNT BRACKET 5 2461415 2 2 STRAP,LIGHT MOUNT 6 35009C 4 4 LOCKWASHER 3/4 7 00000200 4 4 NUT 3/4 NC HEX PL 8 2462536 2 2 PIN,V-RIPPER HINGE 9 00015800 4 4 NUT,TOPLOCK 3/8NC PLB 10 00010600 4 4 HEXB 3/8 NC 2 PL5 11 15B1600 6 6 WASHER 1 SAE P 12 2421094 4 4 LINK,SHORT LIFT 13 2421095 2 2 LINK,LONG LIFT 14 2462533 4 4 PIN,LIFT LINK 15 2457104 2 2 CYLINDER,HYDRAULIC 3 X 8 16 1937156 4 4 SPEC. 90DG ELBOW W/RESTRICTOR 17 37107B13 6 6 CLIP-X HAIR PIN 18 2462538 2 2 PIN, LIFT LINK SHAFT 19 2471045 2 2 PLATE,TRANSPORT LOCK 20 2462532 2 2 PIN,CYLINDER CLEVIS 21 00606000 8 8 PIN-COTTER 3/16 X 2

SHANK Rev 11-04



SHANK Rev 11-04


1 00000200 10 NUT, 3/4" GR82 00002700 2 FLATWASHER, 1/2"3 00037100 2 HEX BOLT, 3/4" X 3" GR84 02027400 1 HEX BOLT5 02962764 2 DECAL, PINCH POINTS6 15B1600 2 WASHER, 1"7 15B1400 2 WASHER, 7/8"8 2430262 1 WELDMENT, PULL ARM PIN9 2430265 3 WELDMENT, SPRING GUIDE BAR10 2431106 1 STOP11 2432300 2 PULL ARM WASHER12 2432301 2 TOGGLE WASHER13 2432521 1 TOGGLE PIN14 2432523 1 PIVOT PIN15 2435507 1 TOGGLE, INNER16 2435508 1 TOGGLE, OUTER17 2435509 2 SPRING END PLUG18 2437424 2 EXTENSION SPRING19 2438332 1 DECAL, 8 HOUR GREASE20 2438403 2 GROOVED PIN21 2438404 2 SHANK WASHER22 2450269 1 WELDMENT, CHISEL POINT23 2460250 1 WELDMENT, SPRING TUBE24 2460251 1 WELDMENT, PIN25 2460252 1 WELDMENT, PIN26 2460282 1* WELDMENT, STRAIGHT POINT27 2460283 1* WELDMENT, WING POINT28 2461079 2 PLATE, CENTER MOUNT29 2461080 2 PLATE, SHANK MOUNT30 2462030 1 PLATE, TIE31 2462512 1 SPRING ANCHOR YOKE32 2462513 1 PIN, ROLLER33 2464866 2 TUBE, ROLLER34 2465502 1 MOUNT, SHANK35 2465503 1 ARM, SHANK PULL36 2465505 1* WEAR SHIN37 2465506 1* SHIN-STRAIGHT SHANK WEAR38 2468350 1* SHANK, AUTO PARABOLIC LONG39 2468351 1* SHANK, AUTO STRAIGHT40 300516H5C 2 HEX TAP, 1/2" NC X 4-1/2" PL541 31102H5C 1 HEX BOLT, 5/16" NC X 5/8" PL542 31103H5C 2 BOLT, 5/16" NC X 5/8" PL543 317026H5C AR HEX BOLT (2 CENTER, 3 LH OR RH) - 3/4" X 11" GR844 317030H5C AR HEX BOLT (1 LH OR RH) - 3/4" X 13" GR845 32905C 1 NUT, 1/2" NC46 3331210C 1 NYLON INSERT JAM LOCKNUT47 331212C 2 NYLON INSERT JAM LOCKNUT48 35002C 1 LOCKWASHER, 5/16"49 35009C 10 LOCKWASHER, 3/4"50 420619 1 ROLL PIN51 420916 1 ROLL PIN52 45051 5 SELF TAPPING ZERK53 45053 1 SELF TAPPING ZERK54 49053 4 COTTER PIN55 6D9016 2 WHIZLOCKNUT

* Optional



DISC GANG Rev 11-04



DISC GANG Rev 11-04

ITEM PART NO. 1700 2200, 2200F 2500 DESCRIPTION

2 2435501 10 10 123 2460446 12 16 18 4 2438362 22 30 34

2468352 22 30 345 2460447 12 16 186 2431150 4 8 87 2436500 4 8 88 2436510 4 8 89 2437500 12 16 1810 2436506 24 32 3611 2460138 12 16 1812 2460246 12 16 1813 31709H5C 24 32 1814 35009C 60 80 9015 00000200 60 80 9019 37054H8C 34 42 48 20 32905C 44 52 1822 2461279 12 26 3023 2461085 22 26 3024 00001800 34 42 4825 00759635 34 42 4826 37051H5C 44 52 6027 330014C 4 6 828 2420218 2 - -

2430303 - 2 22430304 2 - 22430330 - 6 4

29 2438355 2 2 2

SPOOL-MACHINEDSPOOL,MALE BEARINGDISC,CONCAVE SOLID 24 X 6.5MMDISC,CONCAVE SOLID 24 X 8MM FEMALE BEARING SPOOL-MACHINEDNUT LOCK TABMALE END CAPBUMPER END CAPBEARING HANGERTRUNNION MOUNTASY,TRUNNION HOUSING (SEE PAGES 19,20) WDMT,SPRING STOP MOUNT BRACKET HEX CAP 3/4-10 X 3 1/4 GR.5LOCKWASHER 3/4NUT 3/4 NC HEX PLCARRIAGE BOLTHEX LOCKNUT 1/2-13ARM,DISC SCRAPER MOUNTBLADE,DISC SCRAPERLOCKNUT TLM 1/2 NC PLBFLATWASHER 1/2 HRDED NONPLTDCARB 1/2 NC 1 PL5HEX NUT 1 1/2-6AXLE,DISK - 1-1/2 X 95.4 (REAR)AXLE,DISK - 1-1/2 X 65.4AXLE,DISK 1-1/2 X 80-1/2 (FRONT)AXLE,DISK - 1-1/2 X 50.420 X 6.5MM CONCAVE SOLID DISC

2438356 2 2 2 22 X 6.5MM CONCAVE SOLID DISC30 2460730 2 - 2 ANGLE,5-BLADE SCRAPER MOUNT

2460731 2 - - ANGLE,6-BLADE SCRAPER MOUNT2460732 - 6 4 ANGLE,3-BLADE SCRAPER MOUNT2460733 - 2 2 ANGLE,4-BLADE SCRAPER MOUNT

32 31709H8C 36 48 30 HEX CAP 3/4-10 X 3 1/4 GR.833 2461087 12 16 18 PLATE,GANG MOUNT



34 2471070 24 32 36 WASHER, EM BEARING35 37054H8L 22 26 30 CARB, 1/2" NC X 1-3/4"PL5

FRONT MAINFRAME


1 00011400 7 BOLT, 1/4" NC X 3/4" PL52 00015800 8 LOCKNUT, 3/8" NC3 00016400 8 BOLT, 5/8" NC X 8" PL55 00035900 4 HEX BOLT, 5/16" NC X 3/4" PL56 00037200 24 LOCKNUT, 3/4" NC7 00695100 16 LOCKNUT, 5/8" NC8 00776031 1 CANISTER PARTS MANUAL9 02918600 24 HEX BOLT, 3/4" NC X 2" PL810 02959924 3 LOCKNUT, 1/4" NC11 02972565 4 BOLT, 3/8" NC X 4-1/2" PL512 2460239 1 WELDMENT, REAR MAINFRAME13 2460248 1 WELDMENT, FRONT MAINFRAME14 2460253 1 WELDMENT, LIFT CROSSTUBE FRONT15 2460285 1 WELDMENT, LIFT CROSSTUBE REAR16 2461616 1 COVER, VALVE MOUNT17 2461618 1 PLATE, DISC DEPTH18 2461880 1 PLATE, DISC DEPTH POINTER19 2465504 16 CASTING, PIVOT BEARING HOUSING20 2466775 8 BEARING PIVOT21 2467350 1 VALVE, SEQUENCE22 2468304 1 DECAL, DISC DEPTH GAUGE23 316023H8C 8 BOLT, 5/8" NC X 8" PL8



TRUNNION ASSEMBLY 1


2460138 - ASY,TRUNNION HOUSING1 2435520 1 HOUSING,TRUNNION BEARING2 2436800 2 SEAL,2.625 ID X 3.818 OD X .413 2438201 4 RETAINING RING, 3.7504 2436004 1 DBL TAPERED BEARING,1 1/2 SQ B5 00764386 1 GREASE FITTING,8MMX1 STRAIGHT6 00749201 2 BEARING CUP 382A

NOTE: Two styles of Trunnion Housings have been used. See page 20 for more information.



TRUNNION ASSEMBLY 2


2460138 - ASY,TRUNNION HOUSING1 2436800 2 SEAL,2.625 ID X 3.818 OD X .412 2438201 2 RETAINING RING, 3.7503 2436004 1 DBL TAPERED BEARING,1 1/2 SQ B4 00764386 1 GREASE FITTING,8MMX1 STRAIGHT5 2435520A 1 HOUSING,TRUNNION BEARING6 2461731 2 PLATE,TRUNNION SEAL RETAINER7 00749739 6 SELF TAP 1/4 NC 1/28 00749201 2 BEARING CUP 382A

NOTE: Two styles of Trunnion Housings have been used. See page 19 for more information.



HUB & SPINDLE


2460102 - ASY,HUB & SPINDLE1 2465512 1 HUB, MACHINED CASTING2 0536004 1 BEARING, CUP3 2466002 1 CUP, INNER BEARING4 2468404 8 STUD, 5/8 NF X 2-1/2 WHEEL5 2462539 1 SPINDLE, 2-1/2 X 16-3/86 2466700 1 CAP, HUB 7 0536005 1 BEARING CONE8 2466003 1 BEARING CONE9 330910C 1 NUT, HEX SLOTTED 1-1410 2468405 1 COTTER PIN, .200 X 2-1/411 2466802 1 SEAL, GREASE

12 6W300 8 NUT, WHEEL 5/8-18 PL

13 2468604 1 SPINDLE WASHER 1"



LIGHT KIT PARTS



LIGHT KIT PARTS EARTHMASTER 1700 - 2500 (Sept-08) -Current Rev 09-08©2008 Alamo Group Inc. Parts Section – 23

ITEM PART # QTY. DESCRIPTION

1 2460239 1 WELDMENT, REAR MAINFRAME2 2461604 4 BRACKET, UPRIGHT LIGHT3 2461415 2 STRAP, LIGHT MOUNT4 2460260 2 WDMT, MID MOUNT BRACKET5 2461623 4 PLATE, LIGHT BRACKET6 00015800 37 NUT, TOPLOCK 3/8 NC7 32901C 18 HEX LOCKNUT 1/4-208 00726957 2 LIGHT, SINGLE AG-AMB/AMB9 00726956 2 LIGHT, SINGLE AG-RED/BLACK10 00021400 29 HEXB, 1/4 NC X 3/4 PL511 00011400 26 HHCS 3/8 NC X 1 PL512 1458398 4 DECAL, ORANGE REFLECTOR13 1458392 4 DECAL, RED REFLECTOR14 00037200 88 NUT, 3/4-10 CENTERLOCK15 317024H5C 4 HEXB, 3/4 NC X 10 PL516 00726961 2 HARNESS, EXTENSION 10'17 2438621 1 SPADE BRACKET, SMV MOUNTING18 03200347 1 EMBLEM, SMV19 1458393 6 DECAL, YELLOW REFLECTOR20 2438607 1 SOCKET, MOUNTING21 329023C 4 HEX LOCKNUT #10-2422 00726963 1 HARNESS, WISHBONE - 10'23 00753642 6 HHCS 3/8 NC X 1-1/4 PL524 3263N6C 4 PAN HEAD SCREW 10-24 X 1/225 00726964 1 MAIN HARNESS - (NOT SHOWN)



HOSE SCHEMATIC


1 2467202 1 HOSE 400" - YELLOW BAND2 02042400 4 HYDRAULIC ADAPTER, STRAIGHT3 2467201 2 HOSE 110" - RED BAND4 2467200 2 HOSE 90" - BLUE BAND5 2467204 2 HOSE 270" - ORANGE BAND6 2467203 2 HOSE 412" - GREEN BAND7 02962213 11 HYDRAULIC ADAPTER8 00696800 5 HYDRAULIC ADAPTER, STRAIGHT9 2467350 1 VALVE, SEQUENCE



10 2467353 1 VALVE, CUSHION

HOSE SCHEMATIC



HOSE SCHEMATIC FOLDING WING


1 61027400 2 STRAIGHT ADAPTOR 8MP-6MJ2 2467207 2 HOSE #4 - 6FJX - 6FJX - 190LG (GREEN BAND)3 2467106 2 ADAPTER,HYD CROSS4 2467217 4 HOSE #4 - 6FJX - 6FJX - 144LG (ORANGE BAND)5 1937156 8 SPEC. 90DG ELBOW W/RESTRICTOR6 2467215 2 HOSE #4 - 6FJX - 6FJX - 130LG (RED BAND)7 2467216 4 HOSE #4 - 6FJX - 6FJX - 108LG (BLUE BAND)8 00726792 2 ADP HYD TEE 6MJ - 6MJ - 6MJ



HOSE SCHEMATIC FOLDING WING

DISC LIFT CYLINDER


1 2417158 1 CLEVIS CAP2 2417157 1 ROD CAP3 2417160 1 PISTON4 2417159 1 ROD5 2417155 1 TUBE6 2417156 4 TIE ROD7 3047104 2 CLEVIS PIN8 492110 4 CLEVIS PIN CLIP10 * 2 END CAP O-RING11 * 1 ROD WIPER SEAL13 * 1 ROD DUST SEAL14 * 1 PISTON SEAL15 * 2 PISTON WEAR RING16 3047117 1 NYLON THREAD PROTECTOR17 1917140 1 ROD CLEVIS18 0116000 1 SET SCREW20 33005H5C 8 TIE ROD NUT25 5JRC16140 1 PISTON NUT27 1917132 1 PORT PLUG40 * 2 END CAP BACKUP WASHERS* 2417161 1 KIT,SEAL



TONGUE CYLINDER


1 2417158 1 CLEVIS CAP2 2417157 1 ROD CAP3 2417160 1 PISTON4 00774737 1 ROD5 00774748 1 TUBE6 00774742 4 TIE ROD7 3047104 2 CLEVIS PIN8 492110 4 CLEVIS PIN CLIP10 * 2 END CAP O-RING11 * 1 ROD WIPER SEAL13 * 1 ROD DUST SEAL14 * 1 PISTON SEAL15 * 2 PISTON WEAR RING16 3047117 1 NYLON THREAD PROTECTOR17 1917140 1 ROD CLEVIS18 0116000 1 SET SCREW20 33005H5C 8 TIE ROD NUT25 5JRC16140 1 PISTON NUT27 1917132 1 PORT PLUG40 * 2 END CAP BACKUP WASHERS* 2417161 1 KIT,SEAL



MAIN AXLE LIFT CYLINDER


1 2417180 1 CLEVIS CAP2 2417181 1 ROD CAP3 1917149 1 PISTON4 2417182 1 ROD5 1917136 1 TUBE6 1917138 4 TIE ROD7 1917152 2 CLEVIS PIN8 49045 4 CLEVIS PIN CLIP10 * 2 END CAP O-RING11 * 1 ROD WIPER SEAL13 * 1 ROD DUST SEAL14 * 1 PISTON SEAL15 * 2 PISTON WEAR RING16 3047117 1 NYLON THREAD PROTECTOR17 2417183 1 ROD CLEVIS18 00774740 1 SET SCREW20 33017H5C 8 TIE ROD NUT25 1917155 1 PISTON NUT27 1917132 1 PORT PLUG40 * 2 END CAP BACKUP WASHERS* 1917156 1 KIT,SEAL W/PSP SEALS



DISC WING LIFT CYLINDER


2467105 - CYLINDER,HYDRAULIC 3-1/2 X 101 00774728 1 CLEVIS CAP 3.50-3/4 ORB 1.002 2417184 1 CAP,CYLINDER ROD3 00774733 1 PISTON 3.50-1.00-S-WR PSP &2WR4 2417159 1 ROD,CYLINDER 1-1/45 2417185 1 TUBE,CYLINDER6 2417186 4 ROD,CYLINDER TIE7 3047104 2 PIN, 18 49045 4 COTTER PIN 3/16 X 1 3/416 3047117 1 THREAD LOCK17 1917140 1 ROD CLEVIS18 00774740 1 SC SCKT SET 3/8UNCX1/2 KNUR20 33017H5C 8 NUT,HEX 5/8-18 UNF GR.5 PLT25 2417187 1 NUT,CYLINDER PISTON27 1917132 1 SCKT HD O-RNG PLUG,3/4-16 UNF,10 * 2 END CAP O-RING11 * 1 ROD WIPER SEAL13 * 1 ROD DUST SEAL14 * 1 PISTON SEAL15 * 2 PISTON WEAR RING40 * 2 END CAP BACKUP WASHERS* 2417161 1 KIT,SEAL



SEQUENCE VALVE


2467350 - VALVE,SEQUENCE1 2417354 1 BLOCK, MANIFOLD SEQUENCE VALVE2 02962213 4 ADAPTER, HYDRAULIC ELBOW3 00696800 4 ADAPTER, HYDRAULIC STRAIGHT4 2417353 2 VALVE, SEQUENCE - 2000 PSI5 001582 3 PLUG6 2417350 2 VALVE, CHECK7 2417351 1 PLUG8 2417352 1 PLUG



RELIEF VALVE

EARTHMASTER 1700 - 2500 (Sept-08) -Current Rev 09-08©2008 Alamo Group Inc. Parts Section – 31

ITEM PART # QTY. DESCRIPTION 10 2467353 1 BLOCK, RELIEF VALVE11 2467352 1 CARTRIDGE, RELIEF VALVE12 00770346 2 ADAPTER, HYD. STGHT13 02967150 1 ADAPTER, HYD. ELBOW14 2467221 1 HOSE, #8 - #8FJX - #8FJX - 28" LG15 2467222 1 HOSE, #8 - #8FJX - #8FJX - 35" LG16 02761100 2 ADAPTER, HYD. ELBOW17 2467107 1 ADAPTER, HYD. ELBOW18 02766000 2 HEXB 1/4" NC 1-3/4" PL519 32901C 2 HEX LOCKNUT 1/4"-20 2-WAY ZINC20 2461616 1 COVER, VALVE MOUNT

SUPER LINK ASSEMBLY


2450129 - ASY,TOP LINK-M36 X 31 2457504 1 TURNBUCKLE - RH2 2457505 1 TURNBUCKLE - LH3 2457506 1 BODY, TURNBUCKLE TUBE4 2457507 1 COLLAR, TURNBUCKLE LOCKING



PAGE LEFT BLANK INTENTIONALLY

COIL TINE LEVELER 1700 (OPTIONAL) S/N 10077 -CURRENT Rev 09-04



COIL TINE LEVELER 1700 (OPTIONAL) S/N 10077 -CURRENT Rev 09-04


1 00037100 16 HEXB 3/4 NC 2-1/2 PL52 00725712 2 PIN PULL BENT 1/2 X 3 WITH3 00748823 6 HHCS 1/2-13UNC 1-1/2 PL54 00773592 4 PIN, SAFETY LOCK LYNCH5 00999418 78 HHCS 1/2-13UNC 3-1/2 PL56 1458393 2 DECAL,YELLOW REFLECTOR7 2460288 4 WDMT,FRAME TUBE8 2460289 4 WDMT,MOUNT9 2460290 2 WDMT,MOUNT EXTENSION10 2460294 6 WDMT,ANGLE ARM11 2460295 2 WDMT,ADJUSTMENT BAR12 2460304 4 WDMT,PIVOT PIN13 2460332 2 WDMT,INNER CROSS TUBE14 2461080 8 PLATE,SHANK MOUNT15 2464878 4 BUSHING16 2464879 60 BUSHING,TINE17 2464883 6 TUBE,5-COIL TINE BAR18 2467421 4 SRRING,EXTENSION19 2467422 30 TINE,DBL SPRING HARROW COIL20 2468402 4 BOLT,EYE21 2468403 8 U-BOLT22 02675800 8 HHCS 5/8-11UNC 1-1/2 PL523 02957007 4 HHCS 5/8 NC 5 PL824 317026H5C 12 HEX CAP 3/4-10 X 11 GR.525 317028H5C 4 HEX CAP 3/4-10 X 12 GR.526 35009C 32 LOCKWASHER 3/428 2460292 4 WDMT,SHORT MOUNT TUBE32 00001800 84 LOCKNUT TLM 1/2 NC PLB33 00010400 8 NUT 5/8 NC HEX PL34 00695100 28 NUT,TOPLOCK 5/8 NC PLB35 00000200 32 NUT 3/4 NC HEX PL



COIL TINE LEVELER 2500 2200 2200F S/N -CURRENT (OPTIONAL)



COIL TINE LEVELER 2500 2200 2200F S/N -CURRENT (OPTIONAL)

ITEM PART NO. QTY. QTY DESCRIPTION

¤ 2200 2500&2200F

1 2460290 2 2 WDMT,MOUNT EXTENSION2 2460291 4 - WDMT,MOUNT TUBE

2460331 - 4 WDMT,CTL MOUNT TUBE3 2460289 4 4 WDMT,MOUNT4 2460332 2 2 WDMT,INNER CROSS TUBE5 2460333 2 2 WDMT,OUTER WING TUBE6 2464886 6 - TUBE,2-COIL TINE BAR

2464880 - 6 TUBE,3-COIL TINE BAR7 2460294 12 12 WDMT,ANGLE ARM8 00999418 108 120 HHCS 1/2-13UNC 3-1/2 PL59 00001800 120 132 LOCKNUT TLM 1/2 NC PLB10 2467422 36 48 TINE,DBL SPRING HARROW COIL11 2464879 72 84 BUSHING,TINE12 2464887 6 6 TUBE,4-COIL TINE BAR13 2460288 8 8 WDMT,FRAME TUBE14 2468402 4 4 BOLT,EYE15 2467421 4 4 SRRING,EXTENSION16 00773592 4 4 PIN, SAFETY LOCK LYNCH17 2460304 4 4 WDMT,PIVOT PIN18 2468403 8 8 U-BOLT19 2467103 2 2 CYLINDER,HYDRAULIC 2-1/2 X 820 00725712 4 4 PIN PULL BENT 1/2 X 3 WITH21 2464878 4 4 BUSHING23 2460312 2 2 WDMT,CYLINDER PIN24 1937156 4 4 SPEC. 90DG ELBOW W/RESTRICTOR25 2461080 8 8 PLATE,SHANK MOUNT26 1458393 2 2 DECAL,YELLOW REFLECTOR28 2460334 2 2 WDMT,TRANSPORT LOCK PIN29 2460295 4 4 WDMT,ADJUSTMENT BAR30 00010400 8 8 NUT 5/8 NC HEX PL31 02675800 16 16 HHCS 5/8-11UNC 1-1/2 PL532 00695100 36 36 NUT,TOPLOCK 5/8 NC PLB33 02957007 4 4 HHCS 5/8 NC 5 PL834 00000200 32 32 NUT 3/4 NC HEX PL35 35009C 32 32 LOCKWASHER 3/436 00037100 16 16 HEXB 3/4 NC 2-1/2 PL537 317028H5C 4 4 HEX CAP 3/4-10 X 12 GR.538 317026H5C 12 12 HEX CAP 3/4-10 X 11 GR.539 00015800 2 2 NUT,TOPLOCK 3/8NC PLB40 00753642 2 2 HHCS,3/8NC X 1-1/4,ZP,GRD541 00748823 12 12 HHCS 1/2-13UNC 1-1/2 PL542 2467206 2 2 HOSE RED 400"(NOT SHOWN)43 2467207 2 2 HOSE RED 190"((NOT SHOWN)44 2467208 2 2 HOSE RED 206"( (NOT SHOWN)



COIL TINE LEVELER WING CYLINDER (OPTIONAL)


2467103 - CYLINDER,HYDRAULIC 2-1/2 X 81 00774729 1 CLEVIS CAP2 00774734 1 ROD CAP3 2417178 1 PISTON4 00774753 1 ROD5 3047111 1 TUBE6 3047112 4 TIE ROD7 3047104 2 CLEVIS PIN8 49045 4 CLEVIS PIN CLIP10 * 2 END CAP O-RING11 * 1 ROD WIPER SEAL13 * 1 ROD DUST SEAL14 * 1 PISTON SEAL15 * 2 PISTON WEAR RING16 3047117 1 NYLON THREAD PROTECTOR17 1917140 1 ROD CLEVIS18 00774740 1 SET SCREW20 33003H5C 8 TIE ROD NUT25 5JRC12160 1 PISTON NUT27 1917132 1 PORT PLUG40 * 2 END CAP BACKUP WASHERS* 2417179 1 KIT,SEAL 1.125-1.25 PSP



PAGE LEFT BLANK INTENTIONALLY

Parts Section – 1



COIL TINE HOSE SCHEMATIC (OPTIONAL)


1 61027400 2 STRAIGHT ADAPTOR 8MP-6MJ2 2467208 2 HOSE #4 - 6FJX - 6FJX - 206LG3 2467207 2 HOSE #4 - 6FJX - 6FJX - 190LG4 1937156 4 FITTING, 90° ELBOW W/RESTRICTOR5 00726792 2 ADP HYD TEE 6MJ - 6MJ - 6MJ6 2467206 2 HOSE #4 - 6FJX - 6FJX - 400LG



COIL TINE HOSE SCHEMATIC (OPTIONAL)

LIMITED WARRANTY

1. LIMITED WARRANTIES1.01.M&W warrants for one year from the purchase date to the original non-commercial, governmental, or municipal

purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)that the goods purchased are free from defects in material or workmanship.

1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to bedefective under normal use and service due to defects in material or workmanship.

1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, orlubricants, or which has served its normal life. This limited warranty does not apply to any part of any internalcombustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically foundin your Operator’s Manual.

1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of anynature on behalf of Manufacturer.

2. REMEDIES AND PROCEDURES.2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer

within 30 days of purchase.2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the

goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which theclaim is based.

2.03.Purchaser is responsible for returning the goods in question to the Dealer.2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and

service due to defects in material or workmanship, Manufacturer will:(a) Repair or replace the defective goods or part(s) or(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)

if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warrantyby Manufacturer.

The choice of remedy shall belong to Manufacturer.2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and

for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the trans-portation cost for the goods or part(s) from the Dealer to the designated factory.

3. LIMITATION OF LIABILITY.3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES

WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESSFOR A PARTICULAR PURPOSE.

3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FORUSE OF THE GOODS.

3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TOPURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGECAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOTLIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROMTHE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THEABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGESINCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.

3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDERTHIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HASOCCURRED.

4. MISCELLANEOUS.4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,

Texas.4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall

be deemed to be a waiver of any other term.4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the

invalidity of such provision shall not invalidate any other provisions herein.4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

KEEP FOR YOUR RECORDS

ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machineidentification when applying for warranty.

M&W Implement Model _____________________________________ Serial Number________________________________

Date Purchased __________________________________________ Dealer ______________________________________

ATTENTION:READ YOUR OPERATOR'S MANUAL M&W

An Alamo Group Company1020 South Sangamon Ave.

Gibson City, Illinois 60936217-784-4261

M&W

TO THE OWNER/OPERATOR/DEALERTo keep your implement running efficiently and safely, read your manual thoroughly and follow these directions andthe Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easilyfind the information you need.

The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safetyrequirements of tractor operators:

REQUIRED OF THE OWNER:

1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and3. Ensure that each employee uses such Seatbelt while the tractor is moving; and4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected

area provided by the ROPS.

REQUIRED OF THE OPERATOR

1. Securely fasten seatbelt if the tractor has a ROPS.2. Where possible, avoid operating the tractor near ditches, embankments, and holes.3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.4. Stay off slopes too steep for safe operation.5. Watch where you are going - especially at row ends, on roads, and around trees.6. Do not permit others to ride.7. Operate the tractor smoothly - no jerky turns, starts, or stops.8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.9. When the tractor is stopped, set brakes securely and use park lock, if available.

Keep children away from danger all day, every day...

Equip tractors with rollover protection (ROPS) and keep all machineryguards in place...

Please work, drive, play and live each day with care and concern foryour safety and that of your family and fellow citizens.

EM 1700 2200 2200F & 2500 PL 08-13 Printed U.S.A.

P/N 5004WP

LIGHT KIT bom.pdfLIGHT KIT bom.pdfearthm bom

FW BOM.pdfSheet1

RELIEF VALVE BOM.pdfSheet1

FOLDING WING BOM.pdfSheet1

em ADD A PAGE.pdfLIGHT KIT bom.pdfLIGHT KIT bom.pdfearthm bom

FW BOM.pdfSheet1

RELIEF VALVE BOM.pdfSheet1

FOLDING WING BOM.pdfSheet1

rev 13 p/n 5004wp part's manual -...

Documents