residential softeners - yourkinetico.com · residential softeners ... packed bed units are...

Residential Softeners

Revised: 07/2016 Residential Softeners Section 2

Kinetico® Series Models

2020c HE

2020c HF

AquaKinetic® Q237

2040s OD

Certifications NSF 44 NSF 44 NSF 61 NSF 44

WQA 44

Class DIR DIR DIR DIR

Efficiency 3350 Yes Yes

Flow Rate 6.0 gpm 9.1 gpm 9.0 11 gpm

Max. Hardness 30 gpg 20 gpg 37 gpg 44 gpg

Inlet Size ¾” - 1” ¾” - 1” ¾” - 1” ¾” - 1½”

Tank Size 6” x 13” 6” x 13” 8” x 18” 8” x 17”

Distributor Size 1” 1” 1” 1”

Resin Quantity 0.16 cf x 2 0.16 cf x 2 0.30 cf x 2 0.4 cf x 2

Underbed No No No No

Capacities gr / lbs. / gpp gr / lbs. / gpp gr / lbs. / gpp gr / lbs. / gpp

Minimum 2177 / .5 / 4355 1400 / .5 / 2800 4015 / 1 / 4015

Maximum 2775 / .75 / 3700 1870 / .75 / 2493 4366 / 1.25 / 3493 5222 / 1.0 / 5222

Valve Type 1.0” 3 cycle NE 1.0” 3 cycle NE 1.0” 3 cycle NE 1.25” 3 cycle NE

Cycle Initiation Meter Meter Meter Meter

Regen Water / Time

5 gal. / 11 min. 5 gal. / 11 min. 19 gal. / 29 min. 7 gal. / 11 min.

Max Drain Flow 0.9 gpm 0.9 gpm 2.2 gpm 1.6 gpm

Electrical None None None None


Section 2 Residential Softeners Revised: 07/2016

Page-2

Kinetico® Series Models

2040c

2030s

2060s

2060s OD

Certifications NSF 44 NSF 44 NSF 44

WQA 44 WQA 44 WQA 44

Class DIR DIR DIR DIR

Efficiency 3350 Yes Yes Yes Yes

Flow Rate 11 gpm 9 gpm 11.5 gpm 20 gpm

Max. Hardness 44 gpg 45 gpg 66 gpg 30 gpg

Inlet Size ¾” – 1½” ¾” – 1½” ¾” - 1½” ¾” - 1½”

Tank Size 8 x 17” 7” x 35” 8” x 40” 8” x 40”

Distributor Size 1” 1” 1” 1”

Resin Quantity 0.47 cf x 2 0.47 cf x 2 0.7 cf x 2 0.7 cf x 2

Underbed No No No No

Capacities gr / lbs. / gpp gr / lbs. / gpp gr / lbs. / gpp gr / lbs. / gpp

Minimum 7673 / 1.8 / 4263 11500 / 2.7 / 4259 11500 / 2.7 / 4259

Maximum 5222 / 1.0 / 5222 9802 / 2.7 / 3630 15813 / 4.0 / 3953 15813 / 4.0 / 3953

Valve Type 1.25” 3 cycle NE 1.0” 3 cycle NE 1.25” 3 cycle NE 1.25” 3 cycle NE

Cycle Initiation Meter Meter Meter Meter

Regen Water / Time

7 gal. / 11 min. 29 gal. / 40 min. 35 gal. / 45 min. 35 gal. / 45 min.

Max Drain Flow 1.6 gpm 1.6 gpm 2.2 gpm 2.2 gpm

Electrical None None None None



Kinetico Series Models

2100s 2100s OD 2175s

Certifications NSF 44 NSF 44 NSF 44

WQA 44 WQA 44 WQA 44

Class DIR DIR DIR

Efficiency 3350 Yes Yes Yes

Flow Rate 12 gpm 21 gpm 16 gpm

Max. Hardness 107 gpg 57 gpg 175 gpg

Inlet Size ¾” - 1½” ¾” - 1½” 1” - 1½”

Tank Size 10 x 54 10 x 54 13 x 54

Distributor Size 1” 1” 1”

Resin Quantity 1.5 cf x 2 1.5 cf x 2 2.25 cf x 2

Underbed No No 25 lbs. x 2

Capacities gr / lbs. / gpp gr / lbs. / gpp gr / lbs. / gpp

Minimum 24612 / 5.5 / 4474 24612 / 5.5 / 4474 39125 / 8.5 / 4603

Maximum 41087 / 10 / 4108 41087 / 10 / 4108 81845 / 30 / 2728

Valve Type 1.25” 3 cycle NE 1.25” 3 cycle NE 1.25” 3 cycle NE

Cycle Initiation Meter Meter Meter

Regen Water / Time 102 gal. / 90 min. 102 gal. / 90 min. 142 gal. / 90 min.

Max Drain Flow 3.2 gpm 3.2 gpm 5.2 gpm

Electrical None None None

Abbreviations: gr Grains of hardness removed per cycle.

lbs Pounds of NaCl used per cycle. Gpp Grains of hardness removed per pound of salt per cycle.

Notes: All models countercurrent regeneration. Additional salt settings available. Warranty: 10 years. Resin 10 years if carbon combination system or preceded by

dechlorinator, otherwise 7 years.

Kinetico 2020c HF


Page-4

8”

System Components Media Vessel (qty) Size ......................................................... (2) 6 x 13” Media Vessel Construction ...................................... Engineered Plastic Empty Bed Volume .................................................................... 0.16 ft3 Media Type ................................................. Uniform Bead Cation Resin Media Volume ............................................................................ 0.16 ft3 Bed Depth ................................................................................. Packed Free Board .................................................................................... None Riser Tube ................................................................................. 1” ABS Distributor Upper .................0.009” Slots, Engineered Plastic Basket Lower .................. 0.009” Slots, Stainless Steel Flat Plate Under bedding .............................................................................. None Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ................................0.3 - 25.00 gpm Polypropylene Turbine

Inlet Water Quality Pressure Range ................................... 15 – 125 psi Dynamic Pressure Temperature Range ........................................................... 35 – 120o F pH Range ...............................................................................5 – 10 SU Free Chlorine Cl2 (Max.) .......................................................... 2.0 mg/L Hardness as CaCO3 (Max.) ........................................................ 20 gpg

Operating Specs Flow Range (15 / 30 psig) ............................................ 9.10 – 14.9 gpm Flow Configuration ............................................................... Alternating Dimensions (width x depth x height) .................................... 8 x 18 x 19” Weight (Operating / Shipping) .............................................. 85 / 45 lbs.

Connections Inlet / Outlet Connections ......................... Custom Adapter and Bracket Drain Connection ............................................................... 0.065” Tube Brine Line Connection .......................................... .0.25” Tube (internal) Overflow Connection .......................................................... 0.625” Tube Power ........................................................................................... None

System Part Numbers Kinetico 2020c HF ..................................................................... 10706B

Brine Tank Options Tank Description ........................................................................................................................... ...................... ....................... 2020c Cabinet Brine Tank Part Number ................................................................................................................ ...................... ....................... ........... 10704A Tank Height................................................................................................................................... ...................... ....................... .................. 19” Tank Footprint ............................................................................................................................... ...................... ....................... ............ 8 x 18” Material ......................................................................................................................................... ...................... ....................... ................ ABS Salt Capacity ................................................................................................................................. ...................... ....................... ............ 20 lbs.

Regeneration Specifications Regeneration Volume ............................................................. 5 gallons Regeneration Time ............................................................... 11 minutes Backwash Flow Control ...........................................................0.70 gpm Brine Refill Flow Control ..........................................................0.30 gpm

Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 **0.5 lbs. 1,400 grains 2,800 gr./lb. 2.8 lbs./ft3 2 4 5 7 9 11 13 15 **0.75 lbs. 1,870 grains 2,493 gr./lb. 4.2 lbs./ft3 2 5 7 10 13 15 18 20 Gallons/Regeneration: 583 292 194 146 117 97 83 73 **settings certified by NSF and or WQA *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

1.75”

19”

18”

Kinetico® 2020c HF


Service Notes – Kinetico 2020c HF

▶ Meter = 6 gallons per tooth.

▶ Drain port in ⅜” NPT.

▶ This is an upflow unit.

▶ Packed bed units are primarily designed for achieving high efficiency hardness removal.

▶ Maximum ferrous iron is 1.0 ppm. These units should not be used where ferric iron is present.

▶ Must be prefiltered.

▶ Do not attempt to remove distributor tubes. They are snap fit and cannot be removed.

▶ Uses Kinetico 1000 Level One.

▶ Use MED-420 lubricant, part number 11319 on blue quad rings and O-rings.

▶ Do not use Dow 111 silicone on blue seals.

▶ Level 1 center to center is 1¾”.

▶ .5 lb. setting is float pushed all the way down.

▶ .75 lb. setting is 4 ½” from bottom of the valve to the top of the float cup.

Kinetico® 2020c HE


Page-6

8”

System Components Media Vessel (qty) Size ......................................................... (2) 6 x 13” Media Vessel Construction ...................................... Engineered Plastic Empty Bed Volume .................................................................... 0.16 ft3 Media Type ...................................................... Fine Mesh Cation Resin Media Volume ............................................................................ 0.16 ft3 Bed Depth ................................................................................. Packed Free Board .................................................................................... None Riser Tube ................................................................................. 1” ABS Distributor Upper .................0.009” Slots, Engineered Plastic Basket Lower .................. 0.009” Slots, Stainless Steel Flat Plate Under bedding .............................................................................. None Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ................................0.3 - 25.00 gpm Polypropylene Turbine


Operating Specs Flow Range (15 / 30 psig) .............................................. 6.0 – 10.1 gpm Flow Configuration ............................................................... Alternating Dimensions (width x depth x height) .................................... 8 x 18 x 19” Weight (Operating / Shipping) .............................................. 85 / 45 lbs.

Connections Inlet / Outlet Connections ......................... Custom Adapter and Bracket Drain Connection ............................................................... 0.625” Tube Brine Line Connection .......................................... .0.25” Tube (internal) Overflow Connection .......................................................... 0.625” Tube Power ........................................................................................... None

System Part Numbers Kinetico 2020c HE..................................................................... 10705B

Brine Tank Options Tank Description ........................................................................................................................... ...................... ....................... 2020c Cabinet Brine Tank Part Number ................................................................................................................ ...................... ....................... ........... 10704A Tank Height................................................................................................................................... ...................... ....................... .................. 19” Tank Footprint ............................................................................................................................... ...................... ....................... ............ 8 x 18” Material ......................................................................................................................................... ...................... ....................... ................ ABS Salt Capacity ................................................................................................................................. ...................... ....................... ............ 20 lbs.


Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 **0.5 lbs. 2,177 grains 4,385 gr./lb. 2.8 lbs./ft3 3 6 9 12 15 18 20 23 **0.75 lbs. 2,755 grains 3,700 gr./lb. 4.2 lbs./ft3 4 7 11 15 19 23 26 30 Gallons/Regeneration: 583 292 194 146 117 97 83 73 **settings certified by NSF and or WQA *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

1.75”

19”

18”

Kinetico® 2020c HE


Service Notes – Kinetico 2020c HE


▶ Drain port in ⅜” NPT.

▶ This is an upflow unit.

▶ Packed bed units are primarily designed for achieving high efficiency hardness removal.

▶ Maximum ferrous iron is 1.0 ppm. These units should not be used where ferric iron is present.




▶ Use MED-420 lubricant, part number 11319 on blue quad rings and O-rings.

▶ Do not use Dow 111 silicone on blue seals.


▶ .5 lb. setting is float pushed all the way down.

▶ .75 lb. setting is 4 ½” from bottom of the valve to the top of the float cup.

AquaKinetic® Q237


Page-8

24”

System Components Media Vessel (qty) Size ........................................................ (2) 8” x 18” Media Vessel Construction .......Fiberglass Wrapped Engineered Plastic Empty Bed Volume .................................................................... 0.40 ft3 Media Type ................................................... Non Solvent Cation Resin Media Volume ............................................................................ 0.30 ft3 Bed Depth ........................................................................................ 12” Free Board ......................................................................................... 5” Riser Tube ................................................................................. 1” ABS Distributor Upper .................0.014” Slots, Engineered Plastic Basket Lower .................0.014” Slots, Engineered Plastic Basket Under-bedding .............................................................................. None Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ............................. .0.30 - 25.00 gpm Polypropylene Turbine

Inlet Water Quality Pressure Range ................................... 15 – 125 psi Dynamic Pressure Temperature Range ............................................................ 35 – 120o F pH Range ...............................................................................5 – 10 SU Free Chlorine Cl2 (Max.) ...........................................................2.0 mg/L Hardness as CaCO3 (Max.) ........................................................ 37 gpg

Operating Specs Flow Range (15 / 30 psig) .................................................... 8 – 12 gpm Flow Configuration ............................................................... Alternating Dimensions (width x depth x height) ................................. 17” x 8” x 24” Weight (Operating / Shipping) ............................................ 120 / 80 lbs.

Connections Inlet / Outlet Connections ......................... Custom Adapter and Bracket Drain Connection ................................................................... 0.5” Tube Brine Line Connection ....................................................... .0.375” Tube Power ........................................................................................... None

System Part Numbers Q237, 18” x 35” brine drum ......................................................... 13385 Q237, 12” x 16” x 20” brine drum................................................. 13386 Q237, no brine drum ................................................................... 13387

Brine Tank Options Tank Description ........................................................................................................................... ........... 12 x 40 .... 12 x 16 x 20 ........... 18 x 35 Brine Tank Part Number ................................................................................................................ ............ 1479B ............... 7202 ............... 7938 Tank Height................................................................................................................................... ................. 40” .................. 20” .................. 35” Tank Footprint ............................................................................................................................... .......... 12” DIA .......... 12 x 16” ........... 18” DIA Material ......................................................................................................................................... ............. HDPE ............. HDPE ............. HDPE Salt Capacity ................................................................................................................................. .......... 100 lbs. ............. 50 lbs. .......... 250 lbs.

Regeneration Specifications Regeneration Volume ........................................................... 19 gallons Regeneration Time ............................................................... 29 minutes Backwash Flow Control ...........................................................2.00 gpm Brine Refill Flow Control ..........................................................0.40 gpm

Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 1.0 lbs. 4,015 grains 4,015 gr./lb. 3.3 lbs./ft3 4 8 12 16 20 24 27 30 1.25 lbs. 4,366 grains 3,493 gr./lb. 4.2 lbs./ft3 5 10 15 20 24 29 33 37 Gallons/Regeneration: 732 366 244 183 146 122 105 92 *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

1.75”

8”

17”

AquaKinetic® Q237


Service Notes

▶ This unit uses gray control disc part number 7931.

▶ Removable distributor tubes – part number 13392.

▶ Can be used with 18 x 35, 12 x 20, or 12 x 40 brine drum.


▶ Drain port is ⅜” NPT.

▶ This unit can use ¾” or 1” in/out adapters.

▶ This is a downflow service unit.

▶ Uses Kinetico 1000 Level 1.

▶ May be plumbed in ¾ - 1”.


Kinetico® 2040s OD


Page-10

17”

2.5”

System Components Media Vessel (qty) Size ......................................................... (2) 8 x 17” Media Vessel Construction ...................................... Engineered Plastic Empty Bed Volume .................................................................... 0.40 ft3 Media Type ...................................................... Fine Mesh Cation Resin Media Volume ............................................................................ 0.40 ft3 Bed Depth ................................................................................. Packed Free Board .................................................................................... None Riser Tube ................................................................................. 1” ABS Distributor Upper .................0.009” Slots, Engineered Plastic Basket Lower .................. 0.009” Slots, Stainless Steel Flat Plate Under bedding .............................................................................. None Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ................................0.3 - 25.00 gpm Polypropylene Turbine


Operating Specs Flow Range (15 / 30 psig) ............................................. 11.0 - 15.0 gpm Flow Configuration ................................................................ OverDrive Dimensions (width x depth x height) .................................... 17 x 8 x 23” Weight (Operating / Shipping) ............................................ 120 / 90 lbs.


System Part Numbers Kinetico 2040s OD, 12 x 16 x 20 brine tank ................................. 11120 Kinetico 2040s OD, no brine tank ................................................ 11121 Kinetico 2040s OD, no resin, no brine tank ................................. 12526

Brine Tank Options Tank Description .............................................................................................................. K-Spray ........... 12 x 40 .... 12 x 16 x 20 ........... 18 x 35 Brine Tank Part Number ..................................................................................................... 9763A ............ 1479B ............... 7202 ............... 7938 Tank Height.............................................................................................................................. 35” ................. 40” .................. 20” .................. 35” Tank Footprint ................................................................................................................... 18” DIA .......... 12” DIA .......... 12 x 16” ........... 18” DIA Material ............................................................................................................................... HDPE ............. HDPE ............. HDPE ............. HDPE Salt Capacity .................................................................................................................... 200 lbs. .......... 100 lbs. ............. 50 lbs. ........... 250 lbs


Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 1.0 lbs. 5,222 grains 5,222 gr./lb. 2.5 lbs./ft3 7 15 21 27 31 36 40 44 Gallons/Regeneration: 657 329 219 164 131 109 94 82 *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

23”

12”

Kinetico® 2040s OD


Service Notes

▶ Meter = 6.5 gallons per tooth.


▶ These are upflow OD units.

▶ Packed bed units are primarily designed for achieving high efficiencies in hardness removal applications.

▶ Maximum ferrous iron 1.0 ppm. These units should not be used when ferric iron is present.




▶ Use MED-420 lubricant, part number 11319 on blue quad rings and O-rings. Do not use Dow 111 silicone on blue seals.

▶ Can be plumbed in ¾”, 1”, 1¼”, or 1½” plumbing.

▶ Level 1 center to center is 2½”.

Kinetico® 2040c


Page-12

2.5”

27.13”

System Components Media Vessel (qty) Size ......................................................... (2) 8 x 17” Media Vessel Construction .......Fiberglass Wrapped Engineered Plastic Empty Bed Volume .................................................................... 0.40 ft3 Media Type ...................................................... Fine Mesh Cation Resin Media Volume ............................................................................ 0.40 ft3 Bed Depth ................................................................................. Packed Free Board .................................................................................... None Riser Tube ................................................................................. 1” ABS Distributor Upper .................0.009” Slots, Engineered Plastic Basket Lower .................. 0.009” Slots, Stainless Steel Flat Plate Under bedding .............................................................................. None Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ................................0.3 - 25.00 gpm Polypropylene Turbine


Operating Specs Flow Range (15 / 30 psig) ............................................. 11.0 - 15.0 gpm Flow Configuration ................................................................ OverDrive Dimensions (width x depth x height) ................. 11.42” x 11.42” x 27.19” Weight (Operating / Shipping) ............................................ 100 / 81 lbs.

Connections Inlet / Outlet Connections ............................ Custom Adapter and E-clip Drain Connection ................................................................... 0.5” Tube Brine Line Connection ....................................................... .0.375” Tube Power ........................................................................................... None

System Part Numbers Kinetico 2040c ............................................................................ 12502


Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 1.0 lbs. 5,222 grains 5,222 gr./lb. 2.5 lbs./ft3 7 15 21 27 31 36 40 44 Gallons/Regeneration: 657 329 219 164 131 109 94 82 *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

27.19”

11.42”

Kinetico® 2040c


Service Notes



▶ These are upflow OD units.

▶ Packed bed units are primarily designed for achieving high efficiencies in hardness removal applications.

▶ Maximum ferrous iron 1.0 ppm. These units should not be used when ferric iron is present.



▶ Uses Kinetico 1250 Level 1.

▶ Use MED-420 lubricant, part number 11319 on blue quad rings and O-rings. Do not use Dow 111 silicone on blue seals.



▶ Optional salt divider for use with block salt. Part number 12491.

Kinetico® 2030s


Page-14

System Components Media Vessel (qty) Size ......................................................... (2) 7 x 35” Media Vessel Construction ................................ Wrapped Polyethylene Empty Bed Volume .................................................................... 0.70 ft3 Media Type ................................................... Non Solvent Cation Resin Media Volume ............................................................................ 0.47 ft3 Bed Depth ........................................................................................ 22” Free Board ....................................................................................... 13” Riser Tube ................................................................................. 1” ABS Distributor Upper ....................................... 0.014” Slots, ABS Basket Lower ....................................... 0.014” Slots, ABS Basket Under bedding .............................................................................. None Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ............................. .0.30 - 25.00 gpm Polypropylene Turbine


Operating Specs Flow Range (15 / 30 psig) .................................................... 9 – 15 gpm Flow Configuration ............................................................... Alternating Dimensions (width x depth x height) .................................... 15 x 7 x 41” Weight (Operating / Shipping) .......................................... 140 / 105 lbs.


System Part Numbers Kinetico 2030s, 18 x 35 brine drum ........................................... 11020A Kinetico 2030s, 12 X 40 brine drum ........................................... 11084A Kinetico 2030s, K-Spray ............................................................ 11081A Kinetico 2030s, no brine drum ................................................... 11021A Kinetico 2030s, no brine drum, no resin .................................... 11083A

Brine Tank Options Tank Description ........................................................................................................................... ........... 12 x 40 .......... K-Spray ........... 18 x 35 Brine Tank Part Number ................................................................................................................ ............ 1479B ............. 1479B ............... 7938 Tank Height................................................................................................................................... ................. 40” .................. 35” .................. 35” Tank Footprint ............................................................................................................................... .......... 12” DIA ........... 18” DIA ........... 18” DIA Material ......................................................................................................................................... ............. HDPE ............. HDPE ............. HDPE Salt Capacity ................................................................................................................................. .......... 100 lbs. ........... 200 lbs. .......... 250 lbs.


Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 **1.8 lbs. 7,867 grains 4,371 gr./lb. 3.8 lbs./ft3 4 10 14 19 23 27 31 34 2.4 lbs. 8,900 grains 3,708 gr./lb. 5.1 lbs./ft3 5 11 16 22 26 31 35 39 **2.7 lbs. 9,802 grains 3,630 gr./lb. 5.7 lbs./ft3 6 12 18 23 28 33 38 43 3.00 lbs. 10,500 grains 3,500 gr./lb. 6.4 lbs./ft3 7 13 19 25 30 36 41 45 Gallons/Regeneration: 1,253 627 418 313 251 209 179 157 ** Settings certified by NSF and or WQA *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

41”

7” 15”

2.5”

Kinetico® 2030s


Service Notes

▶ Can be plumbed in ¾”, 1”, 1 ¼”, or 1 ½” plumbing.

▶ Uses Kinetico 1250 Level 1 with half louver nozzle.


▶ Drain port is ⅜” NPT x ½” tube.


▶ Uses 18 x 35 standard drum, 12 x 40, or K Spray brine drums.

▶ Meets California efficiency requirements at the 1.8 lb. salt setting.

▶ Level 1 center to center is 2 ½”.

Kinetico® 2060s


Page-16

46”

2.5”

System Components Media Vessel (Qty.) Size ...................................................... (2) 8” x 40” Media Vessel Construction ................................ Wrapped Polyethylene Empty Bed Volume .................................................................... 1.04 ft3 Media Type ................................................... Non Solvent Cation Resin Media Volume ............................................................................ 0.70 ft3 Bed Depth ........................................................................................ 27” Free Board ....................................................................................... 13” Riser Tube ................................................................................. 1” ABS Distributor Upper ....................................... 0.014” Slots, ABS Basket Lower ....................................... 0.014” Slots, ABS Basket Under bedding .............................................................................. None Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ............................. .0.30 - 25.00 gpm Polypropylene Turbine


Operating Specs Flow Range (15 / 30 psig) ............................................ 11.5 – 18.0 gpm Flow Configuration ............................................................... Alternating Dimensions (Width x Depth x Height) ............................... 17” x 8” x 46” Weight (Operating / Shipping) .......................................... 200 / 140 lbs.


System Part Numbers Kinetico 2060s, 18” x 35” brine drum ........................................... 11006 Kinetico 2060s, no brine drum ..................................................... 11007 Kinetico 2060s, no resin, no brine drum ...................................... 11199

Brine Tank Options Tank Description ........................................................................................................................... ........... 12 x 40 .......... K-Spray ........... 18 x 35 Brine Tank Part Number ................................................................................................................ ............ 1479B ............. 9763A ............... 7938 Tank Height................................................................................................................................... ................. 40” .................. 35” .................. 35” Tank Footprint ............................................................................................................................... .......... 12” DIA ........... 18” DIA ........... 18” DIA Material ......................................................................................................................................... ............. HDPE ............. HDPE ............. HDPE Salt Capacity ................................................................................................................................. .......... 100 lbs. ........... 200 lbs. .......... 250 lbs.


Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 **2.7 lbs. 12,481 grains 4,622 gr./lb. 3.9 lbs./ft3 8 15 22 28 34 40 45 50 3.6 lbs. 14,627 grains 4,063 gr./lb. 5.1 lbs./ft3 9 18 27 34 41 48 54 60 **4.0 lbs. 15,813 grains 3,953 gr./lb. 5.7 lbs./ft3 10 19 28 36 44 51 57 63 4.4 lbs. 16,630 grains 3,780 gr./lb. 6.3 lbs./ft3 11 20 29 38 46 53 60 66 Gallons/Regeneration: 1,253 627 418 313 251 209 179 157 ** Settings certified by NSF and or WQA *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

8”

17”

Kinetico® 2060s


Service Notes

▶ This unit uses 1¼” in/out adapters.


▶ Uses 18 x 35, 12 x 40, or K-Spray brine drum.



▶ This unit meets California efficiency requirements at the 2.7 lb. salt setting.

▶ Can be plumbed in ¾”, 1”, 1¼”, 1½” plumbing.

▶ Uses Kinetico 1250 Level One with ½ louver nozzle.


Kinetico® 2060s OD


Page-18

46”

2.5”

System Components Media Vessel (qty) Size ......................................................... (2) 8 x 40” Media Vessel Construction ................................ Wrapped Polyethylene Empty Bed Volume .................................................................... 1.04 ft3 Media Type ................................................... Non Solvent Cation Resin Media Volume ............................................................................ 0.70 ft3 Bed Depth ........................................................................................ 25” Free Board ....................................................................................... 15” Riser Tube ................................................................................. 1” ABS Distributor Upper ....................................... 0.014” Slots, ABS Basket Lower ....................................... 0.014” Slots, ABS Basket Under bedding .............................................................................. None Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ............................. .0.75 - 40.00 gpm Polypropylene Turbine


Operating Specs Flow Range (15 / 30 psig) ............................................ 20.5 – 30.0 gpm Flow Configuration ................................................................. Overdrive Dimensions (width x depth x height) .................................... 17 x 8 x 46” Weight (Operating / Shipping) .......................................... 200 / 140 lbs.


System Part Numbers Kinetico 2060s OD, 18 x 35 brine drum ....................................... 11201 Kinetico 2060s OD, no brine drum ............................................... 11202 Kinetico 2060s OD, no resin, no brine drum ................................ 11789

Brine Tank Options Tank Description ........................................................................................................................... ...................... .......... K-Spray ........... 18 x 35 Brine Tank Part Number ................................................................................................................ ...................... ............. 1479B ............... 7938 Tank Height................................................................................................................................... ...................... .................. 35” .................. 35” Tank Footprint ............................................................................................................................... ...................... ........... 18” DIA ........... 18” DIA Material ......................................................................................................................................... ...................... ............. HDPE ............. HDPE Salt Capacity ................................................................................................................................. ...................... ........... 200 lbs. .......... 250 lbs.


Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 **2.7 lbs. 12,481 grains 4,622 gr./lb. 3.9 lbs./ft3 3 6 9 11 14 17 19 22 **4.0 lbs. 15,813 grains 3,953 gr./lb. 5.7 lbs./ft3 4 7 11 15 18 21 25 28 4.4 lbs. 16,630 grains 3,780 gr./lb. 6.3 lbs./ft3 4 8 12 16 19 23 26 30 Gallons/Regeneration: 3,171 1,586 1,057 793 634 529 453 396 ** Settings certified by NSF and or WQA *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

8”

17”

Kinetico® 2060s OD


Service Notes



▶ Uses Kinetico 1250 Level One with full louver nozzle.



▶ Can be used with 18 x 35, 12 x 40, or K-Spray brine drum.



Kinetico® 2100s


Page-20

60”

2.5”

System Components Media Vessel (qty) Size ....................................................... (2) 10 x 54” Media Vessel Construction ................................ Wrapped Polyethylene Empty Bed Volume .................................................................... 2.19 ft3 Media Type ................................................... Non Solvent Cation Resin Media Volume .............................................................................. 1.5 ft3 Bed Depth ........................................................................................ 36” Free Board ....................................................................................... 18” Riser Tube ................................................................................. 1” ABS Distributor Upper ....................................... 0.014” Slots, ABS Basket Lower ....................................... 0.014” Slots, ABS Basket Under bedding .............................................................................. None Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ............................. .0.30 - 25.00 gpm Polypropylene Turbine

Inlet Water Quality Pressure Range ................................... 15 – 125 psi Dynamic Pressure Temperature Range ........................................................... 35 – 120o F pH Range ...............................................................................5 – 10 SU Free Chlorine Cl2 (Max.) .......................................................... 2.0 mg/L Hardness as CaCO3 (Max.) ...................................................... 107 gpg

Operating Specs Flow Range (15 / 30 psig) ............................................ 12.0 – 19.0 gpm Flow Configuration ............................................................... Alternating Dimensions (width x depth x height) .................................. 21 x 10 x 60” Weight (Operating / Shipping) .......................................... 350 / 175 lbs.


System Part Numbers Kinetico 2100s, 18 x 35 brine drum ............................................. 11031 Kinetico 2100s, no brine drum ..................................................... 11050 Kinetico 2100s, no resin .............................................................. 11051 Kinetico 2100s, no brine drum, no resin ...................................... 11052

Brine Tank Options Tank Description ........................................................................................................................... ...................... ........... 12 x 40 ........... 18 x 35 Brine Tank Part Number ................................................................................................................ ...................... ............. 1479B ............... 7938 Tank Height................................................................................................................................... ...................... .................. 40” .................. 35” Tank Footprint ............................................................................................................................... ...................... ........... 12” DIA ........... 18” DIA Material ......................................................................................................................................... ...................... ............. HDPE ............. HDPE Salt Capacity ................................................................................................................................. ...................... ........... 100 lbs. .......... 250 lbs.

Regeneration Specifications Regeneration Volume ......................................................... 102 gallons Regeneration Time ............................................................... 90 minutes Backwash Flow Control ...........................................................3.00 gpm Brine Refill Flow Control ..........................................................0.70 gpm

Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 **5.5 lbs. 25,253 grains 4,591 gr./lb. 3.7 lbs./ft3 11 21 30 38 -- -- -- -- 7.5 lbs. 30,843 grains 4,112 gr./lb. 5.0 lbs./ft3 14 26 38 48 -- -- -- -- **10 lbs. 41,087 grains 4,108 gr./lb. 6.7 lbs./ft3 17 31 46 58 67 76 85 94 15 lbs. 42,611 grains 2,840 gr./lb. 10.0 lbs./ft3 19 37 52 66 76 88 98 107 Gallons/Regeneration: 1,715 858 572 429 343 286 245 214 ** Settings certified by NSF and or WQA *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

10” 21”

Kinetico® 2100s


Service Notes


▶ Can be plumbed with ¾”, 1”, 1¼” or 1½” plumbing.

▶ Uses Kinetico 1250 Level 1 with half louver nozzle.



▶ Uses 18 x 35 brine tank.

▶ Meets California efficiency requirements at the 5.5 and 10.0 lb. salt settings.


Kinetico® 2100s OD


Page-22

60”

2.5”

System Components Media Vessel (qty) Size ....................................................... (2) 10 x 54” Media Vessel Construction ................................. Wrapped Polyethylene Empty Bed Volume .................................................................... 2.19 ft3 Media Type ................................................... Non Solvent Cation Resin Media Volume .............................................................................. 1.5 ft3 Bed Depth ........................................................................................ 36” Free Board ....................................................................................... 18” Riser Tube ................................................................................. 1” ABS Distributor Upper ....................................... 0.014” Slots, ABS Basket Lower ....................................... 0.014” Slots, ABS Basket Under bedding .............................................................................. None Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ............................. .0.75 - 40.00 gpm Polypropylene Turbine


Operating Specs Flow Range (15 / 30 psig) ............................................ 21.0 – 31.0 gpm Flow Configuration ................................................................. Overdrive Dimensions (width x depth x height) .................................. 21 x 10 x 60” Weight (Operating / Shipping) .......................................... 350 / 175 lbs.


System Part Numbers Kinetico 2100s OD, 18 x 35 brine drum ....................................... 11128 Kinetico 2100s OD, no brine drum ............................................... 11129 Kinetico 2100s OD, no resin, no brine drum ................................ 11777

Brine Tank Options Tank Description ........................................................................................................................... ...................... ........... 12 x 40 ........... 18 x 35 Brine Tank Part Number ................................................................................................................ ...................... ............. 1479B ............... 7938 Tank Height................................................................................................................................... ...................... .................. 40” .................. 35” Tank Footprint ............................................................................................................................... ...................... ........... 12” DIA ........... 18” DIA Material ......................................................................................................................................... ...................... ............. HDPE ............. HDPE Salt Capacity ................................................................................................................................. ...................... ........... 100 lbs. .......... 250 lbs.


Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 **5.5 lbs. 25,253 grains 4,591 gr./lb. 3.7 lbs./ft3 5 10 14 18 22 25 28 30 **10 lbs. 41,087 grains 4,108 gr./lb. 6.7 lbs./ft3 8 15 22 27 33 38 42 46 15 lbs. 42,611 grains 2,840 gr./lb. 10.0 lbs./ft3 10 19 27 34 40 46 52 57 Gallons/Regeneration: 3,829 1,915 1,276 957 766 638 547 479

** Settings certified by NSF and or WQA *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

10”

21”

Kinetico® 2100s OD


Service Notes

▶ Can be plumbed in ¾”, 1” 1¼”, or 1½” plumbing.

▶ Uses Kinetico 1250 Level 1 with full louver.


▶ Drain Port is ⅜” NPT x ½” tube.


▶ Uses 18” x 35” brine drum.

▶ Meets California efficiency requirements at the 5.5 and 10.0 lb. salt settings.


Kinetico® 2175s


Page-24

60”

2.5”

System Components Media Vessel (qty) Size ....................................................... (2) 13 x 54” Media Vessel Construction ................................ Wrapped Polyethylene Empty Bed Volume .................................................................... 3.68 ft3 Media Type ................................................... Non Solvent Cation Resin Media Volume ............................................................................ 2.25 ft3 Bed Depth ........................................................................................ 37” Free Board ....................................................................................... 17” Riser Tube ................................................................................. 1” ABS Distributor Upper ....................................... 0.014” Slots, ABS Basket Lower ....................................... 0.014” Slots, ABS Basket Under bedding ..................................................... 0.25 ft3 ¼ x ⅛ Gravel Regeneration Control ........................................ Non-electric Use Meter Regeneration Type ......................................................... Countercurrent Meter Type ............................. .0.30 - 25.00 gpm Polypropylene Turbine

Inlet Water Quality Pressure Range ................................... 25 – 125 psi Dynamic Pressure Temperature Range ........................................................... 35 – 120o F pH Range ...............................................................................5 – 10 SU Free Chlorine Cl2 (Max.) .......................................................... 2.0 mg/L Hardness as CaCO3 (Max.) ...................................................... 175 gpg

Operating Specs Flow Range (15 / 30 psig) ............................................ 16.0 – 22.0 gpm Flow Configuration ............................................................... Alternating Dimensions (width x depth x height) .................................. 27 x 13 x 60” Weight (Operating / Shipping) .......................................... 450 / 300 lbs.

Connections Inlet / Outlet Connections ............................ Custom Adapter and E-clip Drain Connection ............................................................... 0.625” Tube Brine Line Connection ....................................................... .0.375” Tube Power ........................................................................................... None

System Part Numbers Kinetico 2175s, 24 x 40 brine drum ............................................. 11036 Kinetico 2175s, no brine drum ..................................................... 11054 Kinetico 2175s, resin on the side, no brine drum ......................... 11056 Kinetico 2175s, no resin, no brine drum ...................................... 11832

Brine Tank Options Tank Description ........................................................................................................................... ...................... ....................... ........... 24 x 40 Brine Tank Part Number ................................................................................................................ ...................... ....................... ............. 10586 Tank Height................................................................................................................................... ...................... ....................... .................. 40” Tank Footprint ............................................................................................................................... ...................... ....................... ........... 24” DIA Material ......................................................................................................................................... ...................... ....................... ............. HDPE Salt Capacity ................................................................................................................................. ...................... ....................... .......... 500 lbs.


Disc Selection (Compensated Hardness*) Setting Capacity Efficiency Dosing Meter Disc 1 2 3 4 5 6 7 8 **15 lbs. 65,139 grains 4,342 gr./lb. 6.7 lbs./ft3 27 50 70 88 103 117 129 140 **30 lbs. 81,845 grains 2,728 gr./lb. 13.3 lbs./ft3 34 62 87 110 129 146 162 175 Gallons/Regeneration: 1,715 858 572 429 343 286 245 214 ** Settings certified by NSF and or WQA *Compensated hardness in gpg = Hardness + (3 x Fe in mg/L)

13”

27”

Kinetico® 2175s


Service Notes

▶ May be plumbed in ¾”, 1”, 1¼” or 1½” plumbing.

▶ Uses Kinetico 1250 Level 1 with ½ louver nozzle.

▶ Drain elbow is ½” NPT x 5/8” tube.


▶ Gravel underbed – 24 lbs. per tank.

▶ DO NOT LAY UNIT ON SIDE.


▶ Standard brine tank is 24” x 40”.

▶ An 18” x 35” brine drum can be used for a 15 lbs. salt setting only.



Brine Drum Settings


Page-26

In Kinetico Softeners, the Brine Drum mixes and stores a solution of salt or potassium chloride for regeneration of the softener media. During the Brine Rinse cycle, this solution is drawn from the brine drum and through the media to regenerate it. The Brine Drum contains an adjustment to draw the correct amount of salt or potassium chloride solution for each cycle. This adjustment is made in two places: the Adjuster Tube and the Float Cup. The Adjuster Tube measures the amount of solution that is drawn from the brine drum into the softener during the Brine Rinse cycle. The Float Cup height determines how much softened water flows back into the brine drum to prepare for the next regeneration. Adjuster Tube Setting

The Adjuster Tube is set by cutting and removing tabs on both sides of the tube. Using a pocket-knife, cut across each tab horizontally, following the channel in the plastic, and break off each tab individually until the proper setting is reached. The remaining number or letter imprinted on the tab determines the correct setting. The drawing at right shows an Adjuster Tube at setting "M". Float Cup Setting

The Float Cup is set by adjusting its height above the bottom of the Brine Valve Assembly. By removing the Brine Valve Assembly and resting it on a flat surface, the height of the Float Cup can be measured with a ruler. The height is measured from the base of the Brine Valve Assembly to the top of the Float Cup (see drawing at right). Note that standard settings are defined by markings on the rod of the Brine Valve Assembly. The settings on the rod are listed in the tables at the end of this section. Where the predefined settings are not adequate, the actual Float Cup height, in inches, is listed, and the setting must be measured and set according to the measured Float Cup height. Installing the Brine Valve

After the adjustments have been made to the Adjuster Tube and the Float Cup, the Brine Valve Assembly must be installed in the Brine Drum. Locate the brine valve in the brine well so that

Adjuster Tube (setting= 1.5)

Float Cup Height Adjustment

Float Cup Height

Side View

Brine Well

Top View

Brine Valve Installation

Brine Drum Settings


the ⅜" bent tube is along the back of the brine well away from the brine drum wall. The ⅜" bent tube snaps into a notch and extends from the brine drum about 1". Application

Note: Do not drop the brine valve into the drum! Dropping may lower the Float Cup, resulting

in an improper setting. Determining the correct Brine Valve settings for a particular application is a three-step process:

1. Determine compensated hardness. This requires a hardness test and an iron test on raw water at the application site. Compensated hardness is calculated by multiplying the ferrous iron (in ppm) by 3 and adding it to the grains of hardness.

2. Determine salt setting. The salt setting is determined by taking the compensated hardness (calculated in step 1 above) and using the Specifications Table, located in each specification section, for the proper model of softener to look up a suitable meter disc and salt setting.

3. Determine Adjuster Tube and Float Cup height settings. Use the Brine Drum specifications on the following pages and the model of a Brine Drum to determine the correct settings for both the Adjuster Tube and the Float Cup height.

Note: This process does not apply to the 2080f Greensand Filters. These filters are shipped preset from the factory and do not require setting.

KEY (Salt Setting – pounds of salt)

1.0 = 1.0 E = 3.0 M = 6.0

1.25 = 1.25 F = 3.3 N = 7.5

1.5 = 1.5 G = 3.6 O = 8.5

A = 1.8 H = 4.0 P = 10.0

B = 2.1 J = 4.4 Q = 12.5

C = 2.4 K = 5.0 R = 15.0

D = 2.7 L = 5.5

18 x 35 Brine Drum


Page-28

Standard Settings

1 7¾”

2 8⅝”

3 9½”

4 11⅜”

5 13⅜”

Salt - with Grid

Salt Setting 1.0 1.25 1.5 A B C D E F G H J K L M N O P Q R

Adjuster Tube 1.0 1.25 1.5 A B C D E F G H J K L M N N N N N

Float Cup 1 1 1 1 1 1 1 1 7½” 1 1 1 1 1 1 1 2 3 4 5

Salt - without Grid Salt Setting 1.0 1.25 1.5 A B C D E F G H J K L M N O P Q R

Adjuster Tube J K L M M L N N N L N N N N N N N N N N

Float Cup 6" 6" 6" 6" 6½” 6½” 6" 6¼" 6½” 7¼" 6¾" 7" 7½” 1 8¼" 9" 10" 10¾" 12¼" 14¾"

KCl - with Grid* Salt Setting 1.0 1.25 1.5 A B C D E F G H J K L M N O P Q R

Adjuster Tube 1.25 A B D E F G H J K L M M N N N L J N N

Float Cup 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 3 4 4 12½” 14½”

* Kinetico strongly recommends removing the grid plate when using potassium chloride. KCl - without Grid Salt Setting 1.0 1.25 1.5 A B C D E F G H J K L M N O P Q R

Adjuster Tube K M M N N N N N N N N N M N N N N N N N

Float Cup 6” 6” 6¼” 6” 6¼” 6½” 6¾” 7” 7¼” 7½” 1 8¼” 8¾” 9¼” 2 10½” 11” 12” 13” 14½”

1

2

3

4

5

12 x 40 Brine Drum


Standard Settings

1 7¾"

2 8⅝”

3 9½”

4 11⅜”

5 13⅜”

Salt - with Grid


Adjuster Tube 1.0 1.0 1.25 A E F H J L M N N K M N N N N

Float Cup 2 8¾” 2 2 2 2 2 8¼” 2 2 2 9¼” 4 4 4 4 14” 16”


Adjuster Tube N N N N N N N N N N N N N N N

Float Cup 6” 6¼” 6¾” 7¼” 7½” 8” 8¼” 8¾” 9¼” 9¾” 10¼” 10¾” 11½” 12¼” 13”


Adjuster Tube 1.25 1.5 C G J L K M N K M N M N

Float Cup 2 2 2 2 2 2 3 3 9 4 4 4 5 5

* Kinetico strongly recommends removing the grid plate when using potassium chloride. KCl - without Grid


Adjuster Tube N N N N N N N N N N N N

Float Cup 6¼” 6¾” 7¼” 8” 8½” 8¾” 9¾” 10¼” 10¾” 11¼” 12” 13”

12 x 16 x 20 Brine Drum


Page-30

Standard Settings

1 7¾"

2 8⅝”

3 9½”

4 11⅜”

5 13⅜”

Salt - with Grid


Adjuster Tube 1.5 1.5 A B C D E

Float Cup 7¼” 7½” 7½” 7½” 7½” 7½” 7½”


Adjuster Tube L L L N N N N

Float Cup 6” 6¼” 6½” 6” 6½” 6¾” 7”


Adjuster Tube 1.5 A C E G H J

Float Cup 7½” 7½” 7½” 7½” 7½” 7½” 7¾”

* Kinetico strongly recommends removing the grid plate when using potassium chloride.

KCl - without Grid Salt Setting 1.0 1.25 1.5 A B C D E F G H J K L M N O P Q R

Adjuster Tube M N N N N N N

Float Cup 6¼” 6” 6¼” 6¾” 7¼” 7½” 8”

Mini 15 Brine Drum


Standard Settings

1 7¾"

2 8⅝”

3 9½”

4 11⅜”

5 13⅜”

Salt - with Grid


Adjuster Tube 1.25 1.5 C E F J K

Float Cup 1 1 1 1 1 1 1


Adjuster Tube L N N N N N N

Float Cup 6¼” 6” 6¼” 6¾” 7¼” 7½” 8”


Adjuster Tube B D G J L K M

Float Cup 1 1 1 1 1 2 2

* Kinetico strongly recommends removing the grid plate when using potassium chloride. KCl - without Grid


Adjuster Tube N N N N N N N

Float Cup 6¼” 6½” 7” 7¾” 8¼” 8¾” 9½”

24 x 40 Brine Drum


Page-32

Salt - with Grid

Salt Setting 15 lbs. 25 lbs. 30 lbs. 40 lbs.

Adjuster Tube 1.25 K N N

Float Cup 10½” 12” 11” 16”

Salt - without Grid

Salt Setting 8.5 lbs.

Adjuster Tube D

Float Cup 10½”

Potassium Chloride (KCl) - without Grid

KCL Setting 8.5 lbs. 15 lbs.

Adjuster Tube removed removed

Float Cup 9½” 13½”

K-Spray


Use the following Disc Charts to set up the K–Spray brine drum assembly.

Kinetico 2030s Total Capacity 8,525 grains.

DISC SELECTION CHART Meter Disc Number

KCL Setting 2.4 lbs. 1 2 3 4 5 6 7 8

Compensated Hardness* 4 9 13 17 21 25 27 32

Usable gallons between regeneration 1,250 625 416 312 250 208 178 156

* Compensated hardness is determined by multiplying the number of ppm of ferrous iron x 3 and adding to the actual hardness.

Kinetico 2040s OD Total Capacity 3,950 grains.


KCL Setting .95 lbs. 1 2 3 4 5 6 7 8


Usable gallons between regeneration 650 325 216 162 130 108 92 81


NOTE: Total capacities are lower due to draw time limitations.

Kinetico 2060s Total Capacity 13,205 grains.


KCL Setting 3.5 lbs. 1 2 3 4 5 6 7 8


Usable gallons between regeneration 1,250 625 416 312 250 208 178 156




KCL Setting 3.5 lbs. 1 2 3 4 5 6 7 8


Usable gallons between regeneration 3,200 1,600 1,066 800 640 533 457 400


Kinetico 4060s OD Carbon Total Capacity 13,205 grains.


KCL Setting 3.5 lbs. 1 2 3 4 5 6 7 8

Compensated Hardness* - - - 8 14 20 26 32 38 44

Usable gallons between regeneration 2,200 1,100 773 550 440 366 314 275




KCL Setting 1.7 lbs. 1 2 3 4 5 6 7 8


Usable gallons between regeneration 650 325 216 162 130 108 92 81


Recommendations are based on target concentration of 20% @ 68ºF.

K-Spray


Page-34

Float Dimensions

Kinetico 2040s OD

Kinetico 4040s OD Kinetico 2030s

Kinetico 2060s

Kinetico 2060s OD

Kinetico 4060s OD

Carbon

A ¼” ¼” ¼” ¼”

B 17” 17⅝” 17” 17”

C ¼” ¼” ¼” ¼”

A

B

C

2020c HE & HF


There are two salt settings that can be used on both of these systems. The ¾ lb. setting allows you to increase

gallons between regenerations without replacing the meter disc. The float cup is raised 4 ½” measured from the bottom of the valve to the top of the float cup as shown in Figure 1 below. The ½ lb. setting will allow for the

most salt efficiency. The float cup is pushed all the way down as shown in Figure 2 below. These systems may either use block sale or pellet salt.

H:\Kinetico\Library\DRAWINGS\CONSUMER\CPD Literature Illus\692+738 Tech Manual\Basic Systems\CC2020c - Brine Valve Illustration.dft

Figure 2Figure 1

4 1/2''( 114mm )

3/4 lb Setting 1/2 lb Setting

Figure 1 Figure 2

4 1/4” (107mm)

Notes


Page-36

residential softeners - yourkinetico.com · residential softeners ... packed bed units are...

Documents