remote controlled - top vision group · replacement set v 3 remote to v4 silver – art# 59343s,...
TRANSCRIPT
Top Vision Group – www.topvisiongroup.com
MINO V3
remote controlled
MINO V3 UPGRADE NAAR V4 Mino V3 circuit board replacement
Top Vision Group – www.topvisiongroup.com
Replacement set V3 remote to V4 silver – Art# 59343S, Replacement set V3 remote to V4 white – Art# 59343W
Denk aan het milieu en deponeer de vervangen elektronische onderdelen op de juiste plaats.
1. Verwijder de deksel van de
muurbevestiging
2. Ontkoppel de connector 3. Verwijder het kapje. Verwijder
de afdekkap van de kolom
4. Schroef de printplaat los af 5. Neem de printplaat uit
Ontkoppel deze van de kabel
6. Neem de kunststofonderdelen
uit
- inbussleutel 2mm
- schroevendraaier PH1 Benodigdheden:
V4 circuit board
Art# 75914 Connector
spindle
Art# 75303
Stopper
Art# 75304
Screw
Art# 95034
Damper spindle
Art# 75324
Spindle
Art# 75302
Front cover V3 silver Art# 23079S, Front cover V3 white Art# 23079W
Top Vision Group – www.topvisiongroup.com
7. Schroef de spindle eruit 8. Maak het doosje met nieuwe
onderdelen open
9. Bevestig de nieuwe stopper aan de
spindle op de aangegeven manier.
Schroef de spindle in de kolom totdat
de stopper in de uitsparing klikt
10. Bevestig de damper spindle op
de connector spindle
Plaats deze aan de motor as
11. Zorg voor ca. 2 cm kabellengte
en koppel vervolgens de kabel aan
de printplaat
12. Plaats de printplaat terug in de
kolom. Trek de kabel voorzichtig
door het gaatje heen naar de muur
toe
13. Schroef de printplaat met de
nieuwe schroef vast, gebruik de V3
schroefgat
14. Schuif de nieuwe afdekkap
goed op de kolom
Klik het kapje terug
15. Sluit de Mino connector weer
aan
16. Plaats de deksel van de
muurbevestiging terug
17. Let op! Laat de kolom minimaal
20 keer achterelkaar open en dicht
gaan
De kolom is nu klaar voor gebruik
Top Vision Group – www.topvisiongroup.com
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical unit, basic precautions should always be followed, including the following: Read all instructions before using the Secure Display System DANGER - To reduce the risk of electric shock: 1. Always unplug this unit from the electrical outlet before cleaning. 2. The base of the SECURE DISPLAY SYSTEM contains electronic components. Do not open the base without a qualified electrician or an official Top Vision dealer. WARNING - To reduce the risk of burns, fi re, electric shock, or injury to persons: 1. Unplug from outlet before reassembling parts. 2. Close supervision is necessary when this unit is used by, or near children, invalids, or disabled persons. 3. Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer. 4. Never operate this unit if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the SECURE DISPLAY SYSTEM to a service centre for examination and repair. 5. Keep the cord away from heated surfaces. 6. Never drop or insert any object into any opening. 7. Do not use outdoors / for indoor use only! 8. Do not operate where aerosol (spray) products are being used or where oxygen is being administered. 9. “WARNING: Risk of Electric Shock - Connect this unit to a properly grounded outlet only. See Grounding Instructions.”
SAVE THESE INSTRUCTIONS !
MAINTENANCE INSTRUCTIONS
Instructions for cleaning and user maintenance operations: 1. The exterior of a SECURE DISPLAY SYSTEM may only be cleaned with a non-static brush.
2. The SECURE DISPLAY SYSTEM has no user serviceable parts. All malfunctional or damaged components are to be replaced by a service representative duly authorized by Top Vision Group BV or an official Top Vision dealer.
INTENDED USE 1. The indented use of the Secure Display System is to display eyewear frames and sunglasses. 2. This product is for commercial use only.
Top Vision Group – www.topvisiongroup.com