release notes design-expert upgrade v1.0

7/24/2019 Release Notes Design-Expert Upgrade v1.0

1/8

Release Notes Page 1

Release Notes:

The Unscrambler X Design-Expert

Upgrade v1.0

CAMO Software AS.Nedre Vollgate 8N-0158

Oslo

NORWAYTel: (+47) 223 963 00

Fax: (+47) 223 963 22

CAMO Software Inc.One Woodbridge CenterSuite 319

Woodbridge, NJ 07095

USATel: (+1) 732 726 9200

Fax: (+1) 973 556 1229

CAMO Software India Pvt. Ltd.14 & 15, Krishna Reddy Colony

Domlur Layout

Bangalore - 560 071INDIATel: (+91) 80 4125 4242

Fax: (+91) 80 4125 4181

CAMO Software Japan Co. Ltd.Shibuya 3-chome Square Bldg 2F

3-5-16 Shibuya Shibuya-ku

Tokyo, 150-0002JAPANTel: (+81) 3 6868 7669Fax: (+81) 3 6730 9539


2/8


Table of Contents

Copyright ............................................................................................................................ 3

SCOPE ................................................................................................................................ 3INTRODUCTION .............................................................................................................. 3

PREREQUISITES .............................................................................................................. 4

STATEMENT OF COMPLIANCE .................................................................................... 4

INSTALLATION INSTRUCTIONS.................................................................................. 4ACTIVATION .................................................................................................................... 6

CHANGES .......................................................................................................................... 7

KNOWN ISSUES ............................................................................................................... 8


3/8


Copyright

Information in this document, including URL and other Internet Web site references, is

subject to change without notice.

2015 CAMO Software. All rights reserved.

SCOPEThis document provides installation instructions, features and known issues for The

Unscrambler X Design-Expert Upgrade v1.0.

INTRODUCTIONThe Unscrambler X v10.3 and earlier versions have their own Design of Experiments

(DoE) module, including features for setting up and analyzing experimental designs.

Recently CAMO Software AS went into a partnership with Stat-Ease, Inc., provider of the

Design-Expert Software. Starting with The Unscrambler X v10.4, the previous

Unscrambler X DoE module will be removed and replaced with a link to Design-Expert

Software version 9 (DX9), enabling Unscrambler X users access to the full range of powerful

features within DX9.

This upgrade is provided for users of The Unscrambler X v10.3 that wish to get access to

DX9 before v10.4 is released. It requires The Unscrambler X Service Pack 2014 (SP14)

and is not compatible with any other plugins or upgrades installed after SP14.

The initial bundling of the two software products is basic. An instance of DX9 will open

every time the user attempts to create a design from within The Unscrambler X. The

design itself is created in DX9 and can be analyzed there, and the saved design file can also

be imported back into the Unscrambler X for multivariate analysis. An imported design in

Unscrambler X can also be modified or extended, in which case the current design will be

loaded directly into DX9. The integration of the two software products will be even more

powerful in future versions. For instance methods for multivariate optimization are planned

in The Unscrambler X to fully benefit from applying multivariate methods on designed

data.

Note:The Unscrambler X Design-Expert Upgrade v1.0 will permanently remove all old

DoE functionality and help docs from The Unscrambler X and replace them with DX9

links. These changes are irreversible in the sense that you may uninstall the Design-

Expert Upgrade but previous DoE module will not be restored unless The Unscrambler

X v10.3 is re-installed.


4/8


PREREQUISITESIn order to install The UnscramblerX Design-Expert Upgrade v1.0, Design-ExpertSoftware version 9 has to be pre-installed. It is required that both The UnscramblerX

v10.3 and The UnscramblerX Service Pack 2014 are installed as well.

The upgrade is compatible with below list of products:

1)

The UnscramblerX v10.3, 32-bit

2)

The UnscramblerX v10.3, 64-bit

3)

The UnscramblerX v10.3, Client 32-bit

4)

The UnscramblerX v10.3, Client 64-bit

5)

The UnscramblerX v10.3, 32-bit Japanese version

6)


7)


8)


The Unscrambler X Design-Expert Upgrade v1.0 can be downloaded from the temporary

link below:http://dnld.camo.com/c/26032016-21092015-GAJaaycn/UnscXDesignExpertUpgrade1.0.zip

The Design-Expert Software can be downloaded from the following link:

https://www.statease.com/productattachments/index/download?id=158

All products are also available on CAMOsService and Supportportal. For any questions,

pleasecontactyour local CAMO office.

STATEMENT OF COMPLIANCEThis plugin has been developed following CAMO Softwares quality guidelines, and the

complete changes have been tracked in our revision control system. Where changes have

been introduced in algorithms or functionality, these have been localized to affected

modules only and do not affect other parts of the software. Testing has been performed to

ensure the changes will have no or low compliance impact to the system where the plugin is

installed.

INSTALLATION INSTRUCTIONSMake sure that The UnscramblerX v10.3, The UnscramblerX Service Pack 2014 and

Design-Expert Software version 9 are all installed on your computer. If the Unscrambler

application is running in the background it should be closed before installing the plugin.

Plugins and upgrades to The Unscrambler X v10.3 that are newer than SP14 are not

compatible with the Design-Expert Upgrade v1.0, and installation will be prevented if any

such plugins are detected. In this case the plugins in question must be un-installed before
http://dnld.camo.com/c/26032016-21092015-GAJaaycn/UnscXDesignExpertUpgrade1.0.ziphttps://www.statease.com/productattachments/index/download?id=158https://www.statease.com/productattachments/index/download?id=158http://www.camo.com/osticket/login.phphttp://www.camo.com/osticket/login.phphttp://www.camo.com/osticket/login.phphttp://www.camo.com/contact-us.htmlhttp://www.camo.com/contact-us.htmlhttp://www.camo.com/contact-us.htmlhttp://www.camo.com/contact-us.htmlhttp://www.camo.com/osticket/login.phphttps://www.statease.com/productattachments/index/download?id=158http://dnld.camo.com/c/26032016-21092015-GAJaaycn/UnscXDesignExpertUpgrade1.0.zip


5/8


installing this upgrade. The full set plugins and upgrades currently installed are listed in the

HelpAbout dialog of the Unscrambler X.

Note:After installing the Design-Expert Upgrade v1.0, no additional plugins or upgrades

should be installed, as there might be compatibility issues. Please contact CAMO to verify if

your plugin is compatible with the Design-Expert Upgrade v1.0.

Unzip the content of the plugin and run UnscXDesignExpertUpgrade.msifrom the 32-bit

folder for 32-bit Unscrambler, alternatively run from the 64-bit folder for 64-bit

Unscrambler.

Note:There is another installation file setup.exethat may alternatively be used to install

the plugin. If you are logged in without administrator privileges, you may right-click on

setup.exeand select Run as administrator.

The Windows operating system may ask for confirmation that you want to install the plugin.

Click Yes to these requests. Follow the on-screen instructions to install the product.

Acceptance of the License Agreement is required in order to proceed with the installation:

A confirmation window will verify if installation is successful.

Start The Unscrambler X from the Windows start menu or desktop shortcut. At any time

the installation of the plugin can be verified in the HelpAbout dialogof The

Unscrambler X, in the section Upgrades and Plugins installed.


6/8


The plugin can be un-installed using the regular Windows control panel feature for un-

installing programs (called Add or remove programs, Programs and Features, or similar,depending on Windows version).

Note:The Unscrambler X Design-Expert Upgrade v1.0 will permanently remove all old

DoE functionality and help docs from The Unscrambler X and replace them with DX9links. These changes are irreversible in the sense that you may uninstall the Design-

Expert Upgrade but previous DoE module will not be restored unless The Unscrambler

X v10.3 is re-installed.

ACTIVATIONActivation of Design-Expert Software is required first time it is opened, either from within

The Unscrambler X (using InsertCreate Design or ToolsModify/Extend Design) or

separately. A Design-Expert activation window will open and ask for an activation key

(serial number) in the format dddd-dddd-dddd-ssss (where d is a numeric digit and s is atext character).

This serial number is given in the activation email sent from CAMO Software. If for some

reason this email cannot be found, a new email can be automatically generated by using the

Obtain button in the HelpModify License dialog (see below). This email will contain bothand Activation Key for The Unscrambler X (to be entered in the Modify License dialog)

and a Serial Number for Design-Expert (to be entered in the Design-Expert activation

dialog).

For questions regarding Design-Expert Software activation, pleasecontactyour local

CAMO office.
http://www.camo.com/contact-us.htmlhttp://www.camo.com/contact-us.htmlhttp://www.camo.com/contact-us.htmlhttp://www.camo.com/contact-us.html


7/8


CHANGESID Description Impacts

r158:

Integration of

Design-

Expert

Toolbar menu items for old DoE

module have been removed or

replaced, and new menu items

for interaction with Design-Expert Software version 9

have been added. This affects:

-

FileImport Data

Design-Expert

-

InsertCreate Design

-

TasksAnalyze

Analyze Design Matrix-

ToolsModify/Extend

Design-

Help docs and tutorials

Designs and DoE Analysis results

created with old DoE module can be

loaded into The Unscrambler with the

following limitations:-

Designs will be imported as

regular data tables. These

cannot be exported for

modification or analysis in

Design-Expert Software and

will have to be recreated from

scratch.

-

DoE Analysis models will be

accessible in project navigator

with all result tables, but the

default plots will not be

available.


8/8


KNOWN ISSUES

ID Description Workaround

r1432:

Uninstallation

On uninstallation of the Design-Expert

Upgrade, the previous DoE modules will

not be restored.

To revert to the old

DoE module, reinstall

The Unscrambler Xv10.3 is required.

r1435: Obsolete

help docs

The DoE help docs have been updated, but

some obsolete ones remain in the help doc

browser and installation folder for

technical reasons. Their contents have

been removed. This includes:

-

Design of ExperimentsDialog

usage: Design analysis

-

Design of ExperimentsPlot

interpretations

- Design of ExperimentsTheory

-

TutorialsComplete casesD1:Screening

-

TutorialsComplete casesD2:

Optimization

In addition, some obsolete image files are

retained in installation folder.

None.

r1462: Japanese A Japanese version of the upgrade is not

available. English text given also in

Japanese versions of The Unscrambler X.

None.

r1583: Inactive

control for

responses

In ToolsModify/Extend Design there is a

control for adding response variables to a

design. This control may become greyed

out when toggling between different

design tables, however whatever selection

shown may still be exported.

To activate the control,

close and re-open the

dialog.

release notes design-expert upgrade v1.0

Documents