IOIO

15V

Touch screen display with Front Page displayed

Note: Each block and tab is a touch target

Red solid = over voltage detection, may be connected to a telco/ISDN Red flashing = no cable (no link on fiber)Green solid = link on fiber or MDI connectionAmber solid = link on MDI-X connectionAmber flashing = cable or wire mapper present, and no link

Find the Information You Will Need

Getting Started Guide Everything you will need to quickly get started using the OptiViewTM Analyzer.

Help SystemAnalyzer Help System context sensitive help and expert troubleshooting help.

WebVisit www.flukenetworks.com for the latest news on the OptiViewTM analyzer product, troubleshooting tips, and service information.

OptiViewIntegrated Network Analyzer

Link LED

Transmit LED

Collision LED

Error LED

Line Utilization LEDs 10% increments

Stylus stores at bottom of stand

Status bar

Cable TestDisplays cable information and potential problems. Cable length, cable wire mapping, cable wire pair, impedance, status/anomalies are displayed (e.g., shorts, opens, terminations, and split pairs).

Switch StatisticsAllows you to view multiple ports of a switch simultaneously, thus enabling you to diagnose hard-to-analyze switched remote segments. It provides a multi-port view of switches and routers at a glance.

UtilizationProvides information on the performance and health of the local network segments including the segment to which the analyzer is physically connected.

Keyboard Mouse

Thumb Screws

Tabs

Hard ResetButton

PCCARD

USB

Serial PortCharger jack and status LED

Charger jack and status LED on battery

1000BASE-X GBIC(Pro Gigabit only)

10BASE-T100BASE-TX

LED Charge Status: Flashing = charging, On = charged

100BASE-FX (Pro models only)

Internal wire mapper(Used for patch cord testing.)

Peripheral ConnectionsNetwork Test Interface

Installing External Battery

Analyzer SetupAuto configures for TCP/IP settings, port speed, and duplex mode. The analyzer will determine the best settings, or you can manually override the settings.

Power status and power managementare displayed

Port speed and duplex modeare displayed

Saves currentscreen as HTML report

Prints a graphical representation of what is currently on the screen

On/Off Button

Launches Help

Goes back to previous screen

Stylus

PN 1560798 July 2000 ©2000 Fluke Networks, Inc. All rights reserved. Printed in USA. All product names are trademarks of their respective companies.

TM

TM

Distance to end of cable or port

15V

At a Glance Card

ETHERNET

LINK TRANSMIT COLLISION ERROR% UTILIZATION

Allows you to step through all devices

SwitchRMONhistory

10BASE-T100BASE-TX

Performing a Ping/Trace RouteFiltering and Packet Capture

Adding devices to theKey Devices List

Setting Port Speed and Duplex ModeProtocol StatisticsDisplays the current list of active protocols seen on your network. This list is continuously updated. The right side of this screen displays protocol information in either tabular or pie chart format.

Problem DiscoveryDisplays network devices that are experiencing problems. Problems are reported by Error, Warning, or as Informational.

Network DiscoveryCategorizes IP subnets, NETBIOS domains, and IPX networks.

A problem will be automatically logged if there are no responses from the configured list of key devices.

From the Tools Overview screen, select the Ping tab, then select either the Ping or Trace Route radio button.

Select Ping

Select Trace Route

Use this information to analyze link capabilities and misconfiguration.

Device DiscoveryDisplays network devices, e.g., hosts, switches, routers, etc., on the local broadcast domain.

Enter the device IP address or name, then press Enter

Key devices are seen here

Highlight a device and select Host Detail

Entering devices using the Virtual Keyboard

Launch the Virtual Keyboard

1

From the Tools Overview screen,select Interfaces

Performing WAN Analysis

Connecting the Analyzer

Select WAN

12

1

2

2

1

2

Select Protocoland conversation

Press Filter

Start/Stopcapture

3

1 Select Add to Key DevicesNote: If an existing key device is selected,the button label changes to "Remove."

2Network monitoring

MDIMDI-X

10 Mb half duplex is selectedPress either the Ethernet tabor the port speed/mode button

NIC testing

Cable testOptiViewWire MapAdapter

Cable testopen cable

Cable testPatch Cable

Cable testterminated cable

Cable testlive network

2

1

Launch PacketViewer

4