rc_326us
TRANSCRIPT
8/3/2019 RC_326US
http://slidepdf.com/reader/full/rc326us 1/106 www.enerpac.com
10
10
168
RC-Series, Single-Acting Cylinders
RC cylinder mounting attachments greatly extendthe application possibilities (available for 5, 10,15
and 25 ton cylinders).
Stage lifting set up in Greece, where assembled pipes, 82 feet in length,were stage lifted with six RC-2514 cylinders.
The IndustryStandard General
Purpose Cylinder
Saddles
All RC cylinders areequipped with hardenedremovable grooved saddles.For tilt and flat saddles, see
the RC-Series accessory page.
Page:
Base PlatesTo ensure the stabilityof cylinders for liftingapplications, base platesare available for 10, 25
and 50 ton RC cylinders.
Page:
Specialty Attachments
For solving all kinds ofapplication problems,specialty attach ments areavailable for 5, 10 and 25 tonRC cylinders.
Page:
• The Golden Ring absorbs eccentric loading without gallingcylinder parts
• Collar threads, plunger threads and base mounting holesenable easy fixturing (on most models)
• Designed for use in all positions• High strength alloy steel for durability
• Nickel plating available on most models (contact Enerpacfor details)• Heavy-duty return springs• Baked enamel finish for increased corrosion resistance• CR-400 coupler and dust cap included on all models• Plunger wiper reduces contamination, extending
cylinder life
Shown from left to right: RC-506, RC-50, RC-2510, RC-154, RC-10010, RC-55, RC-1010
8/3/2019 RC_326US
http://slidepdf.com/reader/full/rc326us 2/107®
80%
117
12
58
240
QUICK SELECTION CHARTFor complete technical information see next page.
Single-Acting, General Purpose Cylinders
CylinderEffective
Area
(in2 )
CylinderCapacity
tons(maximum)
Stroke
(in)
CollapsedHeight
(in)
ModelNumber
OilCapacity
(in3 )
Weight
(lbs)
* Available as a set. See note on this page.
** RC-50 cylinder has non-removable grooved saddle and no collar thread.
RCSeries
Capacity:
5-100 tonsStroke:
.63-14.25 inchesMaximum Operating Pressure:
10,000 psi
Gauges
Minimize the risk ofoverloading and ensure long,dependable service fromyour equipment. Refer to
the System Components section for
a full range of gauges.Page:
Think Safety
Manufacturer’s ratingof load and stroke aremaximum safe limits.
Good practice encourages using only80% of these ratings!
Page:
Pump and CylinderSets
All cylindersmarked with an *
are available as sets (cylinder, gauge,couplers, hose and pump) for yourordering convenience.
Page:
Page:
RAC-Series, Single-Acting
CylindersThe lightweight generalpurpose spring returnaluminum cylinders.
Golden Ring Design
The exclusive Golden RingDesign is a unique bearing design whichabsorbs eccentric load stresses to protectyour cylinder against abrasion, over-extendingor plunger blow-outs and jamming or top-end mushrooming. As a result, Golden Ringcylinders provide long, trouble-free operation.
.99
.99
.99
.99
.99.992.242.242.242.242.242.242.242.243.143.14
3.143.143.143.143.143.145.165.165.165.165.165.16
5.165.166.49
11.0411.0411.0411.0415.9015.9020.6320.63
.631.003.005.00
7.009.131.002.134.136.138.00
10.1312.0014.001.002.00
4.006.008.00
10.0012.0014.001.002.004.006.258.25
10.25
12.2514.258.252.004.006.25
13.256.13
13.136.63
10.25
1.634.346.508.50
10.7512.753.534.786.759.75
11.7513.7515.7517.754.885.88
7.8810.6912.6914.6916.6918.695.506.508.50
10.7512.7514.75
16.7518.7515.256.948.94
11.1318.1311.2519.3814.0617.69
.62
.992.984.97
6.969.072.244.759.23
13.7017.8922.6526.8431.313.146.28
12.5718.8525.1331.4237.7043.985.16
10.3120.6332.2342.5552.86
63.1873.4953.5622.0944.1869.03
146.3497.41
208.74136.67211.45
RC-50**RC-51RC-53RC-55*RC-57RC-59RC-101RC-102*RC-104RC-106*RC-108RC-1010*RC-1012RC-1014RC-151RC-152
RC-154*RC-156*RC-158RC-1510RC-1512RC-1514RC-251RC-252*RC-254*RC-256*RC-258RC-2510
RC-2512RC-2514*RC-308RC-502RC-504RC-506*RC-5013RC-756RC-7513RC-1006RC-10010
2.22.33.34.1
5.36.14.05.17.29.8
12.014.015.018.07.29.0
11.015.018.021.024.026.013.014.018.022.027.031.0
36.039.040.033.042.051.083.065.0
130.0130.0160.0
5(4.9)
10(11.2)
15(15.7 )
25(25.8 )
30 (32.4 )
50(55.2 )
75 (79.5 )
100( 103.1)
8/3/2019 RC_326US
http://slidepdf.com/reader/full/rc326us 3/108
3 / 8 "-18 NPTF
V
U
L***M***
D
H
E
A
F
B
D1***
H
W
X
Z
K
A
E
B
O
P
U1
P
O
J
F
V3 / 8 "-18 NPTF
DU
251
RC-Series, Single-Acting Cylinders
ExtendedHeight
B(in)
For full features see page 6.
Stroke
(in)
CylinderCapacity
tons(maximum)
CylinderEffective
Area
(in2 )
CollapsedHeight
A(in)
ModelNumber
OilCapacity
(in3 )
OutsideDiameter
D(in)
RC-50
RC-101 only(U1 = .75 inch)
RC-1006 and RC-10010 models
RC-51 to RC-5013 models
* Available as a set. See page 58.** RC-50 cylinder has non-removable grooved saddle and no collar thread.*** D1 = 1.63 inch, L = .81 inch, M = 1.00 inch.
Speed Chart
See the Enerpac CylinderSpeed Chart in our “YellowPages” to determine your
approximate cylinder speed.
Page:
RC-50**RC-51RC-53RC-55*RC-57RC-59RC-101RC-102*RC-104RC-106*RC-108RC-1010*RC-1012RC-1014RC-151RC-152
RC-154*RC-156*RC-158RC-1510RC-1512RC-1514RC-251RC-252*RC-254*RC-256*RC-258RC-2510
RC-2512RC-2514*RC-308RC-502RC-504RC-506*RC-5013RC-756RC-7513RC-1006RC-10010
.631.003.005.007.009.131.002.134.136.138.00
10.1312.0014.001.002.00
4.006.008.00
10.0012.0014.001.002.004.006.258.25
10.25
12.2514.258.252.004.006.25
13.256.13
13.136.63
10.25
.99
.99
.99
.99
.99
.992.242.242.242.242.242.242.242.243.143.14
3.143.143.143.143.143.145.165.165.165.165.165.16
5.165.166.49
11.0411.0411.0411.0415.9015.9020.6320.63
1.634.346.508.50
10.7512.753.534.786.759.75
11.7513.7515.7517.754.885.88
7.8810.6912.6914.6916.6918.695.506.508.50
10.7512.7514.75
16.7518.7515.256.948.94
11.1318.1311.2519.3814.0617.69
5(4.9)
10(11.2)
15(15.7)
25(25.8)
30 (32.4)
50(55.2)
75(79.5)100
(103.1)
.62
.992.984.976.969.072.244.759.23
13.7017.8922.6526.8431.313.146.28
12.5718.8525.1331.4237.7043.985.16
10.3120.6332.2342.5552.86
63.1873.4953.5622.0944.1869.03
146.3497.41
208.74136.67211.45
2.255.349.50
13.5017.7521.884.536.91
10.8815.8819.7523.8827.7531.755.887.88
11.8816.6920.6924.6928.6932.696.508.50
12.5017.0021.0025.00
29.0033.0023.508.94
12.9417.3831.3817.3832.5020.6927.94
2.311.501.501.501.501.502.252.252.252.252.252.252.252.252.752.75
2.752.752.752.752.752.753.383.383.383.383.383.38
3.383.384.005.005.005.005.005.755.757.007.00
8/3/2019 RC_326US
http://slidepdf.com/reader/full/rc326us 4/109®www.enerpac.com
Single-Acting, General Purpose Cylinders
CylinderBoreDiam.
E(in)
PlungerDiam.
F(in)
Base to Adv. Port
H(in)
SaddleDiam.
J(in)
Weight
(lbs)
PlungerThreadLength
P(in)
SaddleProtrusionfrom Plngr.
K(in)
PlungerInternalThread
O(in)
Base Mounting Holes ModelNumber
CollarThread
W(in)
CollarThreadLength
X(in)
Thread
V(in)
Thrd.Depth
Z(in)
BoltCircle
U(in)
RCSeries
Capacity:
5-100 tonsStroke:
.63-14.25 inchesMaximum Operating Pressure:
10,000 psi
Couplers Included!
CR-400 couplersincluded on all models.Fits all HC-Serieshoses.
RC-50**RC-51RC-53RC-55*RC-57RC-59RC-101RC-102*RC-104RC-106*RC-108RC-1010*RC-1012RC-1014RC-151RC-152
RC-154*RC-156*RC-158RC-1510RC-1512RC-1514RC-251RC-252*RC-254*RC-256*RC-258RC-2510
RC-2512RC-2514*RC-308RC-502RC-504RC-506*RC-5013RC-756RC-7513RC-1006RC-10010
1.131.131.131.131.131.131.691.691.691.691.691.691.691.692.002.00
2.002.002.002.002.002.002.562.562.562.562.562.56
2.562.562.883.753.753.753.754.504.505.135.13
1.001.001.001.001.001.001.501.501.501.501.501.501.501.501.631.63
1.631.631.631.631.631.632.252.252.252.252.252.25
2.252.252.253.133.133.133.133.753.754.134.13
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.751.001.001.001.001.001.001.001.001.001.001.00
1.001.002.251.311.311.381.381.191.191.631.63
**1.001.001.001.001.00
–1.381.381.381.381.381.381.381.501.50
1.501.501.501.501.501.502.002.002.002.002.002.00
2.002.002.002.812.812.812.812.812.812.812.81
**.56.56.56.63.63.25.75.75.75.75.75.75.75
1.001.00
1.001.001.001.001.001.001.001.001.001.001.001.00
1.001.001.00————————
2.22.33.34.15.36.14.05.17.29.8121415187.29
111518212426131418222731
3639403342518365
130130160
**.25.25.25.25.25–
.25
.25
.25
.25
.25
.25
.25
.38
.38
.38
.38
.38
.38
.38
.38
.41
.41
.41
.41
.41
.41
.41
.41
.41
.11
.11
.11
.11
.23
.23
.11
.11
**¾ "-16¾ "-16¾ "-16¾ "-16¾ "-16
#10-24 UN
1"- 81"- 81"- 81"- 81"- 81"- 81"- 81"- 81"- 8
1"- 81"- 81"- 81"- 81"- 81"- 8
1½ "-161½ "- 161½ "- 161½ "- 161½ "- 161½ "- 16
1½ "- 161½ "- 161½ "- 16
————————
.22¼ "-20 UN
¼ "-20 UN
¼ "-20 UN
¼ "-20 UN
¼ "-20 UN
5 16"-18 UN
5 16"-18 UN
5 16"-18 UN
5 16"-18 UN
5 16"-18 UN
5 16"-18 UN
5 16"-18 UN
5 16"-18 UN
⅜ "-16 UN
⅜ "-16 UN
⅜ "-16 UN⅜ "-16 UN
⅜ "-16 UN
⅜ "-16 UN
⅜ "-16 UN
⅜ "-16 UN
½ "-13 UN
½ "-13 UN
½ "-13 UN
½ "-13 UN
½ "-13 UN
½ "-13 UN
½ "-13 UN
½ "-13 UN
—½ "-13 UN
½ "-13 UN
½ "-13 UN
½ "-13 UN
——
¾ "-10 UN
¾ "-10 UN
—1.131.131.131.131.131.061.131.061.131.061.131.061.061.191.19
1.191.191.191.191.191.191.941.941.941.941.941.94
1.941.941.942.192.192.192.191.751.751.751.75
—.56.56.56.56.56.50.50.50.50.50.50.50.50.50.50
.50
.50
.50
.50
.50
.50
.75
.75
.75
.75
.75
.75
.75
.75—.75.75.75.75——
1.001.00
1.131.001.001.001.001.001.561.561.561.561.561.561.561.561.881.88
1.881.881.881.881.881.882.312.312.312.312.312.31
2.312.31—
3.753.753.753.75——
5.505.50
—1½ "-161½ "-161½ "-161½ "-161½ "-162¼ "-142¼ "-142¼ "-142¼ "-142¼ "-142¼ "-142¼ "-142¼ "-142¾ "-162¾ "-16
2¾ "-162¾ "-162¾ "-162¾ "-162¾ "-162¾ "-1635 16"-1235 16"-1235 16"-1235 16"-1235 16"-1235 16"-12
35 16"-1235 16"-1235 16"-12
5"-125"-125"-125"-12
5¾ "-125¾ "-1267/8"-1267/8"-12
8/3/2019 RC_326US
http://slidepdf.com/reader/full/rc326us 5/1010 www.enerpac.com
CD
E H
FG
AB
B
E
D G
F
AH
DC
B
E C
A
B
E
GJ
D
F
A
C
H
C
AB
A
B
C
0-5 °
A
B 0-5 °
E FB
AC D D
AC
EFB
D
A
CE
B
C
D
B
AE
BC
A
C
AB
Tilt
For Usewith
CylinderCapacity
(tons)
Cylinder Accessories
Flat/Threaded Grooved 1) Tilt Base 4) Plunger
BasePlate
Saddles MountingBlock
Clevis Eyes
Base 4)
Plunger
ModelNumber
ModelNumber
Type
A B C D
A
A
B C D E F
A B C
ModelNumber B C D E F G H
JBI-10, -25
REB REP
AW-51 AW-102 (J=.19)RB-5, -10
RB-15, -25 AW-53
JBI-50
Tilt Saddle Dimensions (in)
Mounting Block Dimensions (in)
Clevis Eye Dimensions (in)
1) Standard on 5-30 ton RC-cylinders 2) Except RC-50 3) Except RC-101 4) Mounting screws are included.
Tilt
Pin to Pin*
(in)
Grooved
A B C
Saddle Dimensions (in)
Flat
DIMENSION CHARTSModelNumber
A-53F A-102F A-12 A-29
A-53G A-102G A-152G A-252G
ModelNumber
CAT-10CAT-50
CAT-100
Base Plate Dimensions (in)
* Pin to Pin– REB and REP Clevises fitted. Add cylinder stroke length. 4) Mounting screws are included.
SELECTION CHART
E
RB-5 2), AW-51 2), AW-53 2)
RB-10, AW-102RB-15RB-25RB-25
–––
–
JBI-10–
JBI-25–
JBI-50––
5
101525305075
100
REB-5REB-10REB-15REB-25REP-5REP-10REP-25
RB-5 AW-51 AW-53
RB-10 AW-102RB-15RB-25
JBI-10JBI-25
JBI-50
9.0011.00
12.00
9.0011.00
.60
5.345.53
3.75
2.293.41
5.19
.811.03
1.25
1.752.503.003.751.131.692.25
1.882.632.633.131.622.432.93
.561.001.001.50.56
1.001.50
.63
.88
.881.25.63.88
1.25
.631.001.001.25.63
1.001.25
1.001.381.381.63.75
1.131.38
1½ "-161½ "-161½ "-16
2¼
"-142¼ "-142¾ "-1635/16"-12
3.502.762.874.503.944.005.00
3.002.36.28
3.503.254.506.50
–.43.31–
.63––
1.00.98.75
1.001.181.502.00
–2.132.25
–3.00
––
–¼ "-20¼ "-20
–7/16"-20
––
–1.62.41–
2.31––
REB-5 2)
REB-10REB-15REB-25
––––
REP-5 2)
REP-10 3)
REP-10REP-25REP-25
–––
2.373.073.073.45
———
.68
.881"-8 UNC
1½ "-16 UN
.68
.88
.881.40
1.001.382.002.00
1.001.381.501.97
.25
.241.881.88
.25
.24
.37
.37
A-53F 2)
A-12 3), A-102F 3)
– A-29 A-29
–––
A-53G 2)
A-102G 3)
A-152G A-252G A-252G
–––
–
CAT-10 3)
CAT-10CAT-50CAT-50CAT-100CAT-100CAT-100
.881.40
–
.79
.83
.98
1.381.97
2.80
8/3/2019 RC_326US
http://slidepdf.com/reader/full/rc326us 6/1013®
RAC-202RAC-204
RAC-206RAC-302RAC-304RAC-306RAC-502RAC-504RAC-506RAC-1004RAC-1006RAC-1008RAC-1506
H
K
AE
B
V
Z
J
F
3/8"-18 NPTF
DU
K1
J10-5˚CATG-50
CATG-150CATG-200
RAC-50RAC-100RAC-150
Single-Acting, Spring Return Cylinders
ModelNumber
Weight
(lbs)
SaddleProtrusion
from Plunger
K(in)
SaddleDiameter
J(in)
Base to Advance
Port
H(in)
PlungerDiameter
F(in)
CylinderBore
Diameter
E(in)
OutsideDiameter
D(in)
ExtendedHeight
B(in)
CollapsedHeight
A(in)
OilCapacity
(in3 )
Aluminum vs. Steel
Aluminum cylinders, while offering the most lightweight solution formany lifting, stressing and lowering applications, also have some uniquelimitations due to material properties.
Aluminum differs from steel in that it has a lower finite fatigue life. This meansaluminum cylinders should NOT be used in high-cycle applications such as
production.The Enerpac line of aluminum cylinders are designed to provide 5,000 cycles at theirrecommended pressure. This limit should not be exceeded. In normal lifting andmany maintenance applications, this should provide a lifetime of use.
RACSeries
Capacity:
20-150 tonsStroke:
1.97-7.87 inchesMaximum Operating Pressure:
10,000 psi
Cylinder Model /Capacity
(ton)
SaddleDiameter
J1
Optional Bolt Tilt Saddle Dimensions (in) ModelNumber
SaddleProtrusionfrom Base
K1
Steel Base Plate
The steel base plateprotects the cylinder basefrom damage, it should notbe removed.
The base holes in these aluminumcylinders are designed for securingthe steel base plate. They will notwithstand the capacity of the cylinder.
Do not use the base holes in thesealuminum cylinders to attach any deviceto the cylinder.
ThreadDepth 1)
Z(in)
Thread
V(mm)
BoltCircle
U
(in)
Steel Base Plate Mounting HolesCylinderModel /Capacity
(ton)
1)
Including Base Plate Height of .25 inches.Four (4) baseplate bolts: M6
9.5119.02
28.5213.4826.9740.4521.6343.2764.9087.36
131.04174.72207.76
6.858.82
10.797.139.09
11.067.329.29
11.2610.6712.6414.6113.49
8.8212.76
16.699.09
13.0316.979.29
13.2317.1714.6118.5422.4819.40
3.353.35
3.353.943.943.945.125.125.127.097.097.099.06
2.482.48
2.482.952.952.953.743.743.745.315.315.316.69
1.971.97
1.972.362.362.363.153.153.154.334.334.335.51
1.571.57
1.571.571.571.571.971.971.973.703.703.704.45
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
7.99.0
10.19.9
11.513.018.721.624.543.248.353.473.4
1.071.07
1.071.311.311.311.191.191.191.821.821.822.02
1.973.594.65
1.021.301.46
.47
.47
.47
.47
.47
M6M6M6M6M6
2.763.154.336.307.87
RAC-20RAC-30RAC-50RAC-100RAC-150
.25
8/3/2019 RC_326US
http://slidepdf.com/reader/full/rc326us 7/1014 www.enerpac.com
RACL-302
RACL-304RACL-306RACL-502RACL-504RACL-506RACL-1002RACL-1004RACL-1006RACL-1502RACL-1504RACL-1506
118
117
15
RACL-Series, Aluminum Lock Nut CylindersShown from left to right: RACL-1006, RACL-504 and RACL-506
• Aluminum Lock Nut provides mechanical load holdingfor extended periods
• Hardened steel stop ring increases cylinder life andresistance to side-loads of up to 5%
• Hard coat finish on all surfaces resists damage andextends cylinder life
• Composite bearings increase cylinder life and sideload resistance
• Handles included on all models• Steel baseplate and saddle for protection against
load-induced damage• Integral stop ring prevents plunger over-travel and is
capable of withstanding the full cylinder capacity• High-strength return spring for rapid cylinder retraction• CR-400 coupler and dustcap included on all models• All cylinders meet ASME B-30.1 and ISO 10100 standards
The portable Lock Nut cylinder RACL-1506 used for extended load
support during epoxy injection for bridge reinforcement.
CylinderCapacity
ton(maximum)
Stroke
(in)
ModelNumber
CylinderEffective
Area
(in2 )
To Secure LoadsMechanically
Hoses
Enerpac offers a completeline of high-quality hydraulichoses. To ensure theintegrity of your system,
specify only Enerpac hydraulic hoses.
Saddles
All RACL cylinders areequipped with bolt-onremovable saddles ofhardened steel. For tilt
saddles see next page.
Gauges
Minimize the risk ofoverloading and ensurelong, dependable servicefrom your equipment.
Refer to the System Components
section for a full range of gauges.
Page:
Page:
Page:
1.97
3.945.911.973.945.911.973.945.911.973.945.91
6.85
6.856.85
10.9910.9910.9922.1922.1922.1935.1835.1835.18
30 (34.2)
50 (54.9)
100(110.9)
150(175.9)
8/3/2019 RC_326US
http://slidepdf.com/reader/full/rc326us 8/1015®
H
A
S
E
B
J
F
K
V
Z
3/8"-18NPTF
DU
RACL-302
RACL-304RACL-306RACL-502RACL-504RACL-506RACL-1002RACL-1004RACL-1006RACL-1502RACL-1504RACL-1506
K1
J10-5˚RACL-50
RACL-100RACL-150
CATG-50CATG-150CATG-200
RACL-30RACL-50RACL-100RACL-150
228
Single-Acting, Spring Return, Lock Nut Cylinders
Aluminum vs. Steel
Aluminum cylinders, while offering the most lightweight solution formany lifting, stressing and lowering applications, also have someunique limitations due to material properties.
Aluminum differs from steel in that it has a lower finite fatigue life. Thismeans aluminum cylinders should NOT be used in high-cycle applicationssuch as production.
The Enerpac line of aluminum cylinders are designed to provide 5,000cycles at their recommended pressure. This limit should not be exceeded.In normal lifting and many maintenance applications, this should provide alifetime of use.
Steel Base PlateThe steel base plate protectsthe cylinder base from damage,it should not be removed.
The base holes in these aluminum cylindersare designed for securing the steel baseplate. They will not withstand the capacityof the cylinder.
Do not use the base holes in these aluminumcylinders to attach any device to the cylinder.
OilCapacity
(in3 )
CollapsedHeight
A(in)
ExtendedHeight
B(in)
ModelNumber
Weight
(lbs)
Lock NutHeight
S(in)
SaddleProtrusion
from Plunger
K(in)
SaddleDiameter
J(in)
Base to Advance
Port
H(in)
PlungerDiameter
(Threaded)
F(in)
CylinderBore
Diameter
E(in)
OutsideDiameter
D(in)
Lifting anUnbalanced Load
When lifting an unbalancedload Enerpac SynchronousLift Systems can be the
solution with multiple lift point capabilitiesfrom 4 to 64 points.
RACLSeries
Capacity:
30-150 tonsStroke:
1.97-5.91 inchesMaximum Operating Pressure:
10,000 psi
Cylinder Model /Capacity
(ton)
SaddleDiameter
J1
Optional Bolt On Tilt Saddle Dimensions (in)ModelNumber
SaddleProtrusionfrom Base
K1
ThreadDepth 1)
Z
(in)
Thread
V
(mm)
BoltCircle
U
(in)
Steel Base Plate Mounting HolesCylinderModel /Capacity
(ton)
1) Including Base Plate Height of .25 inches.
Four (4) baseplate bolts: M6
Page:
13.48
26.9740.4521.6343.2764.9043.6887.36
131.1469.25
138.61207.91
11.9
13.414.920.523.426.248.253.358.471.079.888.6
1.97
1.971.971.971.971.972.952.952.953.153.153.15
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
1.58
1.581.581.971.971.973.703.703.704.454.454.45
1.31
1.311.311.191.191.191.821.821.822.022.022.02
2.36
2.362.363.153.153.154.334.334.335.515.515.51
2.95
2.952.953.743.743.745.315.315.316.696.696.69
3.94
3.943.945.125.125.127.097.097.099.069.069.06
11.07
15.0118.9511.2615.2019.1313.6217.5621.5014.6918.6222.56
9.10
11.0713.049.29
11.2613.2311.6513.6215.5912.7214.6916.65
1.973.594.65
1.021.301.46
.24
.47
.47
.47
M6M6M6M6
3.154.336.307.87
.25
8/3/2019 RC_326US
http://slidepdf.com/reader/full/rc326us 9/1016 www.enerpac.com
RACH-202RACH-206RACH-302RACH-306RACH-604RACH-606RACH-1006
118
117
62
CylinderCapacity
ton[maximum]
Stroke
(in)
ModelNumber CylinderEffective Area
(in2 )
The LightweightSolution forTensioning and
Testing
Shown from left to right: RACH-15010, RACH-304 and RACH-208
• Hollow plunger design allows for both pull and push forces• Composite bearings increase cylinder life and side
load resistance• Hard coat finish on all surfaces resists damage and extends
cylinder life• Handles included on all models
• Floating center tube increases seal life• Steel baseplate and saddle for protection against
load-induced damage• Integral stop ring prevents plunger over-travel and is
capable of withstanding the full cylinder capacity• High-strength return spring for rapid cylinder retraction
An RACH-306, powered by a P-392 hand pump, isused to extract corrodedcarriage pins from refusecollection vehicles.
RACH-Series, Hollow Aluminum Cylinders
Hoses
Enerpac offers a completeline of high-quality hydraulichoses. To ensure theintegrity of your system,
specify only Enerpac hydraulic hoses.
Lightweight Hand Pumps
Enerpac hand pumps P-392 or P-802 make the optimallightweight set.
Gauges
Minimize the risk ofoverloading and ensurelong, dependable servicefrom your equipment.
Refer to the System Components sectionfor a full range of gauges.
Saddles
All RACH-cylinders areequipped with bolt-onremovable hardened steelhollow saddles.
Page:
Page:
Page:
20 [25.3]
30 [39.6]
60 [65.6]
100 [127.5]
1.975.911.975.913.945.915.91
5.075.077.927.92
13.1313.1325.51
8/3/2019 RC_326US
http://slidepdf.com/reader/full/rc326us 10/10
3/8"-18 NPTF
Z
V
H
A
B
K
F
P
OJ
Y U D
E
RACH-202RACH-206RACH-302RACH-306RACH-604RACH-606RACH-1006
RACH-20RACH-30RACH-60RACH-100
RACHSeries
Capacity:
20-100 tonsStroke:
1.97-5.91 inchesCenter Hole Diameter:
1.06-3.11 inches
Aluminum vs. Steel
Aluminum cylinders, while offering the most lightweight solutionalso have some unique limitations due to material properties.It differs from steel in that it has a lower finite fatigue life.
Aluminum cylinders should NOT be used in high-cycle applicationssuch as production.
These cylinders are designed to provide 5000 cycles at their recommendedpressure. This limit should not be exceeded . In normal lifting and manymaintenance applications, this should provide a lifetime of use.
Maximum Operating Pressure:
10,000 psi
Single-Acting, Spring Return, Hollow Plunger Cylinders
Standard Features
• CR-400 coupler and dust cap
• All cylinders meet ASMEB-30.1 and ISO 10100standards.
Steel Base Plate
The steel base plateprotects the cylinder basefrom damage, it should notbe removed.
The base holes in these aluminumcylinders are designed for securingthe steel base plate. They will notwithstand the capacity of the cylinder.
Do not use the base holes in these
aluminum cylinders to attach any deviceto the cylinder.
OilCapacity
(in3 )
CollapsedHeight
A(in)
ExtendedHeight
B(in)
ModelNumberWeight
(lbs)
CenterHoleDiameter
Y(in)
SaddleProtrusionfrom Plunger
K(in)
SaddleDiameter
J(in)
Base to AdvancePort
H(in)
PlungerDiameter
F(in)
CylinderBoreDiameter
E(in)
OutsideDiameter
D(in)
ThreadDepth 1)
Z
(in)
Thread
V
(mm)
BoltCircle
U
(in)
Steel Base Plate Mounting HolesCylinderModel /Capacity
(ton)
1) Including Base Plate Height of .25 inches.Four (4) baseplate bolts: M6
9.9829.9415.5946.7751.6977.53
150.64
11.515.717.624.743.050.3
101.9
1.061.061.341.342.132.133.11
.39
.39
.39
.39
.47
.47
.55
2.172.172.762.763.9439.45.71
1.141.141.141.142.412.412.41
2.172.172.762.763.943.945.71
2.952.953.743.745.125.127.28
3.943.945.125.127.097.099.84
9.3718.3210.1719.0216.3420.8721.31
7.4112.418.20
13.1212.4114.9715.39
.47
.47
.47
.47
M6M6M6M6
3.154.336.299.05
.25