raymond thermal process questionnaire_2011

Upload: jacklyn-keller

Post on 07-Jan-2016

216 views

Category:

Documents


0 download

DESCRIPTION

tag

TRANSCRIPT

Please complete this form, including the reverse side, and return it to the address shown

ALSTOM Power Inc.

Raymond and Bartlett-Snow Products

4525 Weaver Parkway, Ste. 250

Warrenville, IL 60555 US

Tel: 630.393.1000

www.bartlettsnow.com

THERMAL PROCESSING QUESTIONNAIRE

DRYING - COOLING - CALCINING

Please complete this form, including the reverse side, and return it to the address shown above.

Name:

FORMTEXT Position:

FORMTEXT Date:

FORMTEXT

.

Company: Address:

City:

State: Zip: Country:

Telephone: Mobile:

Email: Fax:

1. Type of processing desired: FORMCHECKBOX Drying FORMCHECKBOX Calcining FORMCHECKBOX Cooling FORMCHECKBOX Other

2. Material to process:

3. Chemical composition:

4. Desired changes to material, such as chemical reactions, etc.:

5. End use of product:

6. Processing basis: FORMCHECKBOX 24hr/day or FORMCHECKBOX hr/day ( or FORMCHECKBOX batch

7. Capacity rate: lb/hr or kg/hr ( lb/batch or kg/batch

8. Capacity basis: FORMCHECKBOX feed rate or FORMCHECKBOX product rate

9. Material Properties: (Please specify units) Feed DischargeScreen Analysis:FeedDischarge

Moisture content (free)%%+16 mesh (1mm)%%

Moisture content (bound)%%+30 mesh (500() %%

Volatile content%%+50 mesh (300() %%

Volatile heating value +100 mesh (150()%%

Bulk density +200 mesh (74 () %%

Specific gravity+325 mesh (44 () %%

Specific heatTop size

Angle of reposeAverage size

What is the general nature of the process material? FORMCHECKBOX free flowing FORMCHECKBOX sticky FORMCHECKBOX abrasive FORMCHECKBOX corrosive

FORMCHECKBOX plastic FORMCHECKBOX other

10. Process temperatures: (Please specify FORMCHECKBOX (F or FORMCHECKBOX (C)

Feed temperature Max. temperature material can be exposed to

Temperature material must be heated to Temperature at which material gets sticky

Temperature material must be cooled to (if applicable) Melting temperature for process material

11. General Process Information (as applicable):

DRYING: Can the process material be brought into contact with products of combustion?

COOLING: Can atmospheric air be brought into contact with the process material to effect cooling?

Do you prefer that cooling be done indirectly to maintain a neutral or special atmosphere?

If the process material is cooled indirectly, what approach is desired? FORMCHECKBOX air FORMCHECKBOX water FORMCHECKBOX other

CALCINING: Is a special reaction gas or atmosphere required for the process, and if so what gas or gases must

be used ?

Is the reaction FORMCHECKBOX endothermic or FORMCHECKBOX exothermic?

How long should the process material remain at temperature to process it properly?

Can the process material be brought into contact with products of combustion?

12. Which of the following metals do you prefer in contact with the material processed?

FORMCHECKBOX carbon steel FORMCHECKBOX stainless steel FORMCHECKBOX Inconel FORMCHECKBOX aluminum FORMCHECKBOX abrasion resistant steel FORMCHECKBOX other

13. What utilities are available?

(a) Heat source (Please specify units)

FORMCHECKBOX gas

type

pressure Heating value

FORMCHECKBOX oil

type

pressure Heating value

FORMCHECKBOX coal

type

size Heating value

FORMCHECKBOX steam

type

pressure quality

FORMCHECKBOX waste heat gases type

quantity temperature

(b) Electricity main

Electricity controlvolts

volts phase

phase hertz hertz

(c) Water - temperature rate pressure

14. Insurance code requirements FORMCHECKBOX GE CAP FORMCHECKBOX FM GLOBAL FORMCHECKBOX NFPA FORMCHECKBOX CSA FORMCHECKBOX CE FORMCHECKBOX other

15. Plant location:

FORMCHECKBOX indoors FORMCHECKBOX outdoors

Elevation: Ambient Temp Minimum: Maximum:

16. Remarks:

Page 1of 2