POWER CONVERTERS

CLAMPS

OTHER PRODUCTS

Ph: +1 (919)

POWER CONVERTERS

CLAMPS

OTHER PRODUCTS

Ph: +1 (919)

POWER CONVERTERS

OTHER PRODUCTS

Ph: +1 (919)-481 6895

RRAANNGG

ELECTRONIC BOARDS

HEATSINKS

481 6895

GGEE OOFF

IIGG

ELECTRONIC BOARDS

HEATSINKS

www.adelser.com

FF DDRRIIVVEE

IIGGBBTT//MM

ELECTRONIC BOARDS

www.adelser.com

EERRSS SSOO

//MMOOSSFF

www.adelser.com

OOLLUUTTIIOO

SFFEETT

OONNSS FFOO

Page

FFOORR

Page 1

RRAANNGGEE OOFF DDRRIIVVEERRSS SSOOLLUUTTIIOONNSS

FFOORR IIGGBBTT//MMOOSSFFEETT

Ph: +1 (919) 481-6895 www.adelser.com Page 2

DDUUAALL IIGGBBTT//MMOOSSFFEETT DDRRIIVVEERR CCAARRDD

11WW AARRCCAALL 22110066

"SCALE TECHNOLOGY"

The ARCAL2106 board is an intelligent double IGBTs and MOSFETs driver. All functions needed for power converters development are embedded on a small size, very versatile single board.

High isolation and dv/dt immunity

1W / ±6A per output

Short-circuit protection

Power supply monitoring

high or low logic error feedback

CMOS or HCMOS input level

Tuneable dead time

±15V or 0/+15V Gate voltage

11.. AABBSSOOLLUUTTEE MMAAXXIIMMUUMM RRAATTIINNGGSS

All data refer to 25°C and VDD=15V unless otherwise specified.

Symbol Parameter Min. Max. Unit VDD Supply voltage (referred to ground) 0 16 VDC VI Logic input voltage 0 VDD VDC IG Peak Gate current -6 +6 A PG Output power for each channel 1 W VISO Isolation test voltage (AC / 50Hz /1min) 4000 Veff VOP Operating voltage 800 VDC dv/dt dv/dt immunity @ ∆V=1000V 100 KV/µs

TA Operating temperature -40 +85 °C TS Storage temperature -40 +90 °C VOC Error feedback open collector max. voltage 40 V IOC Error feedback open collector max. current 10 mA

RRAANNGGEE OOFF DDRRIIVVEERRSS SSOOLLUUTTIIOONNSS

FFOORR IIGGBBTT//MMOOSSFFEETT

Ph: +1 (919) 481-6895 www.adelser.com Page 3

22.. EELLEECCTTRRIICCAALL CCHHAARRAACCTTEERRIISSTTIICCSS

All data refer to 25°C and VDD=15V unless otherwise specified.

22..11.. PPoowweerr SSuupppplliieess

Symbol Parameter Min. Typ. Max. Unit VDD Nominal supply voltage 14.5 15 15.5 VDC IDD0 No-load max. supply current 58 mA IDC0 DC/DC converter no-load input current 23 mA IDD Max. supply current 192 mA

η DC/DC converter efficiency 85 %

VTH0 power supply monitoring threshold voltage 11.5 V H Power supply monitoring hysteresis 0.7 V

22..22.. IInnppuutt ssttaaggee

Symbol Parameter Min. Typ. Max. Unit VIM Max. logic input voltage 0 VDD VDC VIT+ Low to High input threshold voltage (5V/15V) 3.4/10 V VIT- High to Low input threshold voltage (5V/15V) 1.7/5 V FSW Switching frequency 0 >100 KHz α Duty cycle 0 100 % RIN Input resistance 10 15 KΩ TDT Standard dead time 5.5 µs

22..33.. OOuuttppuutt ssttaaggee

Symbol Parameter Min. Typ. Max. Unit IG Max. gate current -6 +6 A VG+ Turn-on gate output voltage +15 V VG- Turn-off gate output voltage -15/0 V TR Rise time 110 ns TF Fall time 80 ns TPD+ Input / output turn-on delay time 500 ns TPD- Input / output turn-off delay time 500 ns TB Blocking time after failure 1 s TER Default feedback duration 70 ms TCE VCE monitoring reaction time 10.4 µs VTHX VCE monitoring threshold voltage 8.2/6.6 V

RRAANNGGEE OOFF DDRRIIVVEERRSS SSOOLLUUTTIIOONNSS

FFOORR IIGGBBTT//MMOOSSFFEETT

Ph: +1 (919) 481-6895 www.adelser.com Page 4

DDUUAALL IIGGBBTT//MMOOSSFFEETT DDRRIIVVEERR CCAARRDD

33WW AARRCCAALL 22331155

"SCALE TECHNOLOGY"

The ARCAL2315 board is an intelligent double IGBTs and MOSFETs driver. All functions needed for power converters development are embedded on a small size, very versatile single board.

High isolation and dv/dt immunity

3W / ±15A per output

Short-circuit protection

Power supply monitoring

high or low logic error feedback

CMOS or HCMOS input level

Tuneable dead time

±15V or 0/+15V Gate voltage

Turn-On and Turn-Off control

11.. AABBSSOOLLUUTTEE MMAAXXIIMMUUMM RRAATTIINNGGSS

All data refer to 25°C and VDD=15V unless otherwise specified.

Symbol Parameter Min. Max. Unit VDD Supply voltage (referred to ground) 0 16 VDC VI Logic input voltage 0 VDD VDC IG Peak Gate current -18 +18 A PG Output power for each channel 3 W VISO Isolation test voltage (AC / 50Hz /1min) 4000 Veff VOP Operating voltage 1200 VDC dv/dt dv/dt immunity @ ∆V=1000V 100 KV/µs

TA Operating temperature -40 +85 °C TS Storage temperature -40 +90 °C VOC Error feedback open collector max. voltage 40 V IOC Error feedback open collector max. current 10 mA

RRAANNGGEE OOFF DDRRIIVVEERRSS SSOOLLUUTTIIOONNSS

FFOORR IIGGBBTT//MMOOSSFFEETT

Ph: +1 (919) 481-6895 www.adelser.com Page 5

22.. EELLEECCTTRRIICCAALL CCHHAARRAACCTTEERRIISSTTIICCSS

All data refer to 25°C and VDD=15V unless otherwise specified.

22..11.. PPoowweerr SSuupppplliieess

Symbol Parameter Min. Typ. Max. Unit VDD Nominal supply voltage 14.5 15 15.5 VDC IDD0 No-load max. supply current 90 mA IDC0 DC/DC converter no-load input current 30 mA IDD Max. supply current 531 mA

η DC/DC converter efficiency 85 %

VTH0 power supply monitoring threshold voltage 11.5 V H Power supply monitoring hysteresis 0.7 V

22..22.. IInnppuutt ssttaaggee

Symbol Parameter Min. Typ. Max. Unit VIM Max. logic input voltage 0 VDD VDC VIT+ Low to High input threshold voltage (5V/15V) 3.4/10 V VIT- High to Low input threshold voltage (5V/15V) 1.7/5 V FSW Switching frequency 0 >100 KHz α Duty cycle 0 100 % RIN Input resistance 10 15 KΩ TDT Standard dead time 5.5 µs

22..33.. OOuuttppuutt ssttaaggee

Symbol Parameter Min. Typ. Max. Unit IG Max. gate current -15 +15 A VG+ Turn-on gate output voltage +15 V VG- Turn-off gate output voltage -15/0 V TR Rise time 110/160 ns TF Fall time 80/130 ns TPD+ Input / output turn-on delay time 500 ns TPD- Input / output turn-off delay time 500 ns TB Blocking time after failure 1 s TER Default feedback duration 70 ms TCE VCE monitoring reaction time 10.4 µs VTHX VCE monitoring threshold voltage 8.2/6.6 V

RRAANNGGEE OOFF DDRRIIVVEERRSS SSOOLLUUTTIIOONNSS

FFOORR IIGGBBTT//MMOOSSFFEETT

Ph: +1 (919) 481-6895 www.adelser.com Page 6

CCOONNTTRROOLL MMOODDUULLEE FFOORR TTHHRREEEE--PPHHAASSEE

IIGGBBTT OORR MMOOSSFFEETT CCOONNVVEERRTTEERR

"SCALE TECHNOLOGY"

The control module ARCAL E+ includes 3 complementary boards :

• ARCAL E+ TOP

• ARCAL E+ SCREEN

• ARCAL E+ BOT This module is designed to be used with IGBTs type ECONOPACK+©. On these 3 electronic boards, you have all the functionalities needed for the design of 3-phase converters.

High isolation and dv/dt immunity

1W / ±6A per output

Short-circuit protection

‘Active Clamping’ protection

Detection of supply default

Tuneable dead time

±15V or 0/+15V Gate voltage

11.. AABBSSOOLLUUTTEE MMAAXXIIMMUUMM RRAATTIINNGGSS

All data refer to 25°C and VDD=15V unless otherwise specified.

Symbol Parameter Min. Max. Unit VDD Supply voltage (referred to ground) 0 16 VDC VI Logic input voltage 0 VDD VDC IG Peak Gate current -6 +6 A PG Output power for each channel 1 W VISO Isolation test voltage (AC / 50Hz /1min) 4000 Veff VOP Operating voltage 800 VDC dv/dt dv/dt immunity @ ∆V=1000V 100 KV/µs

TA Operating temperature -40 +85 °C TS Storage temperature -40 +90 °C VOC Error feedback open collector max. voltage 40 V IOC Error feedback open collector max. current 10 mA

RRAANNGGEE OOFF DDRRIIVVEERRSS SSOOLLUUTTIIOONNSS

FFOORR IIGGBBTT//MMOOSSFFEETT

Ph: +1 (919) 481-6895 www.adelser.com Page 7

22.. EELLEECCTTRRIICCAALL CCHHAARRAACCTTEERRIISSTTIICCSS

All data refer to 25°C and VDD=15V unless otherwise specified.

22..11.. PPoowweerr SSuupppplliieess

Symbol Parameter Min. Typ. Max. Unit VDD Nominal supply voltage 14.5 15 15.5 VDC IDD0 No-load max. supply current 150 180 mA IDC0 DC/DC converter no-load input current 70 mA IDD Max. supply current 550 600 mA

η DC/DC converter efficiency 85 %

VTH0 power supply monitoring threshold voltage 11.5 V H Power supply monitoring hysteresis 0.7 V

22..22.. IInnppuutt ssttaaggee

Symbol Parameter Min. Typ. Max. Unit VIM Max. logic input voltage 0 VDD VDC VIT+ Low to High input threshold voltage (15V) 10 V VIT- High to Low input threshold voltage (15V) 5 V FSW Switching frequency 0 >100 KHz α Duty cycle 0 100 % RIN Input resistance 10 15 KΩ TDT Standard dead time 5.5 µs

22..33.. OOuuttppuutt ssttaaggee

Symbol Parameter Min. Typ. Max. Unit IG Max. gate current -6 +6 A VG+ Turn-on gate output voltage +15 V VG- Turn-off gate output voltage -15 V TR Rise time 110 ns TF Fall time 80 ns TPD+ Input / output turn-on delay time 500 ns TPD- Input / output turn-off delay time 500 ns TB Blocking time after failure 1 s TER Default feedback duration 70 ms TCE VCE monitoring reaction time 10.4 µs VTHX VCE monitoring threshold voltage 8.2/6.6 V

RRAA

FFOO

Ph: +1 (919)

DD

The control module ARCAL E+ be usefunctionalities needed

11..

All data refer to 25°C and V

SymbolV

VIGPVVdv/dt

TTVIOC

RRAANNGGEE OOFF

OORR IIGGBBTT

Ph: +1 (919)

DDOOUUBBLL

The control module ARCAL E+ be used with IGBTs type ECONOPACK+©. functionalities needed

High isolation and dv/dt immunity

3W / ±15A per output

Short-circuit protection

Detection of supply default

Default signal in p

Compatible CMOS inputs

Adjustable dead times

±15V grid input

‘Active Clamping’ protection

Measure of temperature through CTN, Measure of current with an external sensor

AABBSSOOLLUUTT

All data refer to 25°C and V

Symbol VDD

VI G

PG VISO VOP dv/dt

TA TS VOC OC

FF DDRRIIVVEERR

TT//MMOOSSFF

Ph: +1 (919) 481-6895

LLEE DDRRII

The control module ARCAL E+ d with IGBTs type ECONOPACK+©.

functionalities needed to control the module as 1 leg, with 3 IGBTs in parallel

High isolation and dv/dt immunity

3W / ±15A per output

circuit protection

Detection of supply default

Default signal in positive logic

Compatible CMOS inputs

Adjustable dead times

±15V grid input

‘Active Clamping’ protection

Measure of temperature through CTN, Measure of current with an external sensor

TTEE MMAAXXIIMMUU

All data refer to 25°C and V

ParameterPower supply voltage (with reference to the exposed conductive part)Logic input voltagePeak Gate currentOutput power for each channelIsolation test voltage (AC / 50Hz /1min)Operating voltage

dv/dt immunity @ Operating temperatureStorage temperatureError feedback open collector max. voltageError feedback open collector max. current

EERRSS SSOOLLUU

FFEETT

6895

IIVVEERR FF

AA

"SCALE

The control module ARCAL E+ 3P d with IGBTs type ECONOPACK+©.

to control the module as 1 leg, with 3 IGBTs in parallel

High isolation and dv/dt immunity

3W / ±15A per output

circuit protection

Detection of supply default

ositive logic

Compatible CMOS inputs

Adjustable dead times

‘Active Clamping’ protection

Measure of temperature through CTN, Measure of current with an external sensor

UUMM RRAATTIINNGG

All data refer to 25°C and VDD=15V unless

Parameter Power supply voltage (with reference to the exposed conductive part) Logic input voltage Peak Gate current Output power for each channel

test voltage (AC / 50Hz /1min)Operating voltage

dv/dt immunity @ ∆V=1000VOperating temperatureStorage temperature Error feedback open collector max. voltage

feedback open collector max. current

UUTTIIOONNSS

www.adelser.com

FFOORR EECC

AARRCCAA

"SCALE T

3P includes 3 complementary boards. d with IGBTs type ECONOPACK+©.

to control the module as 1 leg, with 3 IGBTs in parallel

High isolation and dv/dt immunity

ositive logic

Measure of temperature through CTN, Measure of current with an external sensor

GGSS

=15V unless otherwise specified.

Power supply voltage (with reference to the exposed

Output power for each channel test voltage (AC / 50Hz /1min)

V=1000V Operating temperature

Error feedback open collector max. voltage

feedback open collector max. current

www.adelser.com

ECCOONNOO

AALL EE++

TECHNOLOGY

ncludes 3 complementary boards. d with IGBTs type ECONOPACK+©. On these 3 electronic boards, you have all the

to control the module as 1 leg, with 3 IGBTs in parallel

Measure of temperature through CTN, Measure of current with an external sensor

otherwise specified.

Power supply voltage (with reference to the exposed

test voltage (AC / 50Hz /1min)

Error feedback open collector max. voltagefeedback open collector max. current

www.adelser.com

OOPPAACC

++ 33PP

ECHNOLOGY"

ncludes 3 complementary boards. On these 3 electronic boards, you have all the

to control the module as 1 leg, with 3 IGBTs in parallel

Measure of temperature through CTN, Measure of current with an external sensor

otherwise specified.

Power supply voltage (with reference to the exposed

Error feedback open collector max. voltage feedback open collector max. current

CCKK++©©

ncludes 3 complementary boards. This module is designed to On these 3 electronic boards, you have all the

to control the module as 1 leg, with 3 IGBTs in parallel.

Measure of temperature through CTN, Measure of current with an external sensor

Min. Max.0 16

0 V-18 +18 3 4000 12100

-40 +85-40 +90 40 10

Page

© MMOODDUU

This module is designed to On these 3 electronic boards, you have all the

Measure of temperature through CTN, Measure of current with an external sensor

Max. Unit16 VDC

VDD VDC

+18 A 3 W 4000 Veff1200 VDC

KV/µs

+85 °C +90 °C 40 V 10 mA

Page 8

UULLEESS

This module is designed to On these 3 electronic boards, you have all the

Measure of temperature through CTN, Measure of current with an external sensor

Unit DC

DC

Veff DC

KV/µs

RRAANNGGEE OOFF DDRRIIVVEERRSS SSOOLLUUTTIIOONNSS

FFOORR IIGGBBTT//MMOOSSFFEETT

Ph: +1 (919) 481-6895 www.adelser.com Page 9

22.. EELLEECCTTRRIICCAALL CCHHAARRAACCTTEERRIISSTTIICCSS

All data refer to 25°C and VDD=15V unless otherwise specified.

22..11.. PPoowweerr SSuupppplliieess

Symbol Parameter Min. Typ. Max. Unit VDD Nominal supply voltage 14.5 15 15.5 VDC IDD0 No-load max. supply current 90 mA IDC0 DC/DC converter no-load input current 30 mA IDD Max. supply current 531 mA

η DC/DC converter efficiency 85 %

VTH0 power supply monitoring threshold voltage 11.5 V H Power supply monitoring hysteresis 0.7 V

22..22.. IInnppuutt ssttaaggee

Symbol Parameter Min. Typ. Max. Unit VIM Max. logic input voltage 0 VDD VDC VIT+ Low to High input threshold voltage (5V/15V) 3.4/10 V VIT- High to Low input threshold voltage (5V/15V) 1.7/5 V FSW Switching frequency 0 >100 KHz α Duty cycle 0 100 % RIN Input resistance 10 15 KΩ TDT Standard dead time 2 µs

22..33.. OOuuttppuutt ssttaaggee

Symbol Parameter Min. Typ. Max. Unit IG Max. gate current -15 +18 A VG+ Turn-on gate output voltage +15 V VG- Turn-off gate output voltage -15 V TR Rise time 110/160 ns TF Fall time 80/130 ns TPD+ Input / output turn-on delay time 500 ns TPD- Input / output turn-off delay time 500 ns TB Blocking time after failure 1 s TER Default feedback duration 70 ms TCE VCE monitoring reaction time 10.4 µs VTHX Trigger thresholds on Vce 4.15/2.35 V OVERTEMP Trigger threshold of CTN temperature 110 115 120 °C VTHX VCE monitoring threshold voltage 8.2/6.6 V I Gain on measure of current 4.77 4.9 4.97

RRAANNGGEE OOFF DDRRIIVVEERRSS SSOOLLUUTTIIOONNSS

FFOORR IIGGBBTT//MMOOSSFFEETT

Ph: +1 (919) 481-6895 www.adelser.com Page 10

FFIIBBRREE DDIISSTTRRIIBBUUTTEEDD DDAATTAA IINNTTEERRFFAACCEE FFOORR

AARRCCAALL DDRRIIVVEERRSS

The ARCAL-FO board is a fibre distributed data – control signals interface. One board is enough to drive up to 3 ARCAL drivers at the same time. This board includes two control optical fibres for each channel as well as an optical fibre for the return default. Each HE14 connector enables to connect a driver board of the ARCAL range. The ARCAL-FO-E+ board is a fibre distributed data – control signals interface. It enables to drive an ARCAL-E+210 board mounted on an Econopack+ module in a three-phase structure. Basically it enables to send the temperature measure of the IGBT done by the ARCAL-E+210. It can also measure the Bus voltage of the stack where it is mounted. This board is compatible with the ARC-MC-E+ too, which measures 3 phase currents and one Bus voltage, then processes and sends the defaults to the HE10 connector – 26 compatible pins with the ARCAL-FO-E+.

Fibre distributed data interface

Measure of DC Bus voltage

Centralizes on an « Error » optical fibre the 3 IGBT defaults of the drivers as well as the temperature default

RRAANNGGEE OOFF DDRRIIVVEERRSS SSOOLLUUTTIIOONNSS

FFOORR IIGGBBTT//MMOOSSFFEETT

Ph: +1 (919) 481-6895 www.adelser.com Page 11

POWER CONVERTERS ELECTRONIC BOARDS

CLAMPS HEATSINKS

OTHER PRODUCTS

Ph: +1 (919)-481 6895 www.adelser.com Page 12

CAUTION : ADELSER reserves the right to make modifications to its technical data and product specifications at any time without prior notice. These documents have no contractual value

For more information:

ADELSER, INC 2200 Gateway Centre Blvd Suite 213 Morrisville, NC 27560

+1 (919) 481-6895 Fax: +1 (919) 481-6910 Email:info@adelser.com

NOTES