radio sony cdx-3300s
TRANSCRIPT
-
7/29/2019 Radio Sony CDX-3300s
1/4
2004 Sony Corporation Printed in Korea
3-261-846-21(1)
CautionsThis unit is designed for negative earth 12 V DC
operation only.D o not get the leads under a screw, or caught in
moving parts (e.g. seat railing).Bef ore making connections, turn the car ignition
off to avoid short circuits.Connect the yellow and red power input leads
only after all other leads have been connected. Run all earth leads to a common earth point.Be s ure to insulate any loose unconnected leads
with electrical tape for safety.
Notes on the power supply lead (yellow)When connecting this unit in combination with
other stereo components, the connected carcircuits rating must be higher than the su m ofeach components fuse.
When no car circuits are rated high enough,connect the unit directly to the battery.
Parts Iist (1)The numbers in the list are keyed to those in the
instructions.The bracket 1 and the protection collar 5 are
attached to the unit before shipping. Beforemounting the unit, use the release keys 6 toremove the bracket 1 and the protection collar 5from the unit. For details, see Removing theprotection collar and the bracket (4) on thereverse side of the sheet.
Keep the release keys6for future use as theyare also necessary if you remove the unit fromyour car.
CautionHandle the bracket 1 carefully to avoid injuringyour fingers.
NoteBefore installing, make sure that the catches on both
sides of the bracket1 are bent inwards 2 mm. If thecatches are straight or bent outwards, the unitwill not be installed securely and may spring out.
Connection example (2)Notes (2-B) Be sure to connect the earth lead before connecting
the amplifier. If you connect an optional power amplifier and do not
use the built-in amplifier, the beep sound will bedeactivated.
Installation/Connections
Instalacin/Conexiones
FM/AMCompact DiscPlayer
Connection diagram (3)1 To a metal surface of the car
First connect the black earth lead, then connect theyellow and red power input leads.
2 To the power aerial control lead or powersupply lead of aerial booster amplifier
Notes It is not necessary to connect this lead if there is no
power aerial or aerial booster, or with a manually-operated telescopic aerial.
When your car has a built-in FM/AM aerial in therear/side glass, see Notes on the control and
power supply leads.
3 To AMP REMOTE IN of an optional poweramplifierThis connection is only for amplifiers. Connectingany other system may damage the unit.
4 To the +12 V power terminal which is energizedin the accessory position of the ignition keyswitch
Notes If there is no accessory position, connect to the +12
V power (battery) terminal which is energized atall times.Be sure to connect the black earth lead to a metal
surface of the car first. When your car has a built-in FM/AM aerial in the
rear/side glass, see Notes on the control and
power supply leads.5 To the +12 V power terminal which is energized
at all timesBe sure to connect the black earth lead to a metal
surface of the car first.
Notes on the control and power supply leads The power aerial control lead (blue) supplies +12 V DC
when you turn on the tuner. When your car has built-in FM/AM aerial in the rear/
side glass, connect the power aerial control lead (blue)or the accessory power input lead (red) to the powerterminal of the existing aerial booster. For details,consult your dealer.
A power aerial without relay box cannot be used withthis unit.
Memory hold connectionWhen the yellow power input lead is connected, powerwill always be supplied to the memory circuit even whenthe ignition key is turned off.
Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and
with adequate power handling capacities to avoid itsdamage.
Do not connect the speaker terminals to the carchassis, or connect the terminals of the right speakers
with those of the left speaker. Do not connect the earth lead of this unit to thenegative () terminal of the speaker.
Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speakerterminals may damage the unit.
To avoid a malfunction, do not use the built-in speakerleads installed in your car if the unit shares a commonnegative () lead for the right and left speakers.
Do not connect the units speaker leads to each other.
Note on connectionIf speaker and amplifier are not connected correctly,FAILURE appears in the display. In this case, make surethe speaker and amplifier are connected correctly.
2
A
B
AUDIO OUT REAR
Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)
Rear speaker
Altavoz posterior
Front speaker
Altavoz frontal
1
Power amplifier
Amplificador de potencia
Active subwoofer
Subwoofer activo
CDX-R3300CDX-R3300SCDX-R3000
Catch1
Rotary commander RM-X4S
Mando rotativo RM-X4S
RM-X4S
1 2
4
3
4 6 75
2
-
7/29/2019 Radio Sony CDX-3300s
2/4
12 V
1
1 5 6 1 5 4
6
1
1 2 mm
2
2-B
3
1
2
FM/AM
3 AMP REMOTE IN
4 +12 V
+12 V
FM/AM
5 +12 V
+12 V
FM/AM
4-8
(-)
(- )
FAILURE
Precauciones Esta unidad ha sido diseada para alimentarse slo
con cc de 12 V de masa negativa. No coloque los cables debajo de ningn tornillo, ni
los aprisione con partes mviles (p.ej. los rales delasiento).
Antes de realizar las conexiones, desactive elencendido del automvil para evitar cortocircuitos.
Conecte los cables de entrada de alimentacinamarillo y rojo solamente despus de haberconectado los dems.
Conecte todos los conductores de puesta amasa a un punto comn.
Por razones de seguridad, asegrese de aislar concinta aislante los cables sueltos que no estnconectados.
Notas sobre el cable de suministro dealimentacin (amarillo) Cuando conecte esta unidad en combinacin con
otros componentes estreo, la capacidad nominaldel circuito conectado del automvil debe sersuperior a la suma del fusible de cada componente.
Si no hay circuitos del automvil con capacidadnominal suficientemente alta, conecte la unidaddirectamente a la batera.
Lista de componentes (1) Los nmeros de la lista corresponden a los de las
instrucciones. La unidad se comercializa con el soporte1 y el
marco de proteccin5 instalados. Antes demontarla, utilice las llaves de liberacin6 paraextraer el soporte1 y el marco de proteccin5.Para obtener ms informacin, consulteExtraccin del marco de proteccin y del soporte(4) en el reverso de la hoja.
Conserve las llaves de liberacin6 parautilizarlas en el futuro, ya que tambin lasnecesitar si retira la unidad del automvil.
PrecaucinTenga mucho cuidado al manipular el soporte1para evitar posibles lesiones en los dedos.
NotaAntes de instalar la unidad, compruebe que losenganches de ambos lados del soporte1 estn dobladoshacia adentro 2 mm. Si no lo estn o estn doblados haciaafuera, la unidad no se instalar correctamente y puede
saltar.
Ejemplo de conexiones (2)Notas (2-B) Asegrese de conectar primero el cable de toma a tierra
antes de realizar la conexin al amplificador. Si conecta un amplificador de potencia opcional y no
utiliza el incorporado, los pitidos se desactivarn.
Diagrama de conexin (3)1 A una superficie metlica del automvil
Conecte primero el cable de toma a tierra negro, y despuslos cables amarillo y rojo de entrada de alimentacin.
2 Al cable de control de la antena motorizada o al cablede fuente de alimentacin del amplificador de antenaNotas Si no se dispone de antena motorizada ni de amplificador
de antena, o se utiliza una antena telescpica accionadamanualmente, no ser necesario conectar este cable.
Si el automvil incorpora una antena de FM/AM en elcristal trasero o lateral, consulte Notas sobre los cablesde control y de fuente de alimentacin.
3 Para conectar a AMP REMOTE IN del amplificador depotencia opcionalEsta conexin es slo para amplificadores. La conexin decualquier otro sistema puede daar la unidad.
4 Al terminal de alimentacin de +12 V que recibeenerga en la posicin de accesorio del interruptor dela llave de encendidoNotas Si no hay posicin de accesorio, conctelo al terminal de
alimentacin (batera) de +12 V que recibe energa sininterrupcin.
Asegrese de conectar primero el cable de toma a tierranegro a una superficie metlica del automvil.
Si el automvil incorpora una antena de FM/AM en elcristal trasero o lateral, consulte Notas sobre los cablesde control y de fuente de alimentacin.
5 Al terminal de alimentacin de +12 V que recibeenerga sin interrupcinAsegrese de conectar primero el cable de toma a tierranegro a una superficie metlica del automvil.
Notas sobre los cables de control y de fuente dealimentacin El cable de control de la antena motorizada (azul)
suministrar cc de + 12 V cuando conecte la alimentacin delsintonizador.
Si el automvil dispone de una antena de FM/AMincorporada en el cristal trasero o lateral, conecte el cable decontrol de antena motorizada (azul) o el cable de entrada dealimentacin auxiliar (rojo) al terminal de alimentacin delamplificador de antena existente. Para obtener msinformacin, consulte a su proveedor.
Con esta unidad no es posible utilizar una antena motorizadasin caja de rel.
Conexin para proteccin de la memoriaSi conecta el conductor de entrada amarillo, el circuito de lamemoria recibir siempre alimentacin, aunque ponga la llavede encendido en la posicin OFF.
Notas sobre la conexin de los altavoces Antes de conectar los altavoces, desconecte la alimentacin
de la unidad. Utilice altavoces con una impedancia de 4 a 8 con la
capacidad de potencia adecuada para evitar que se daen. No conecte los terminales de altavoz al chasis del automvil,
ni conecte los terminales del altavoz derecho con los delizquierdo.
No conecte el cable de toma a tierra de esta unidad alterminal negativo () del altavoz.
No intente conectar los altavoces en paralelo. Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplificadores incorporados) a los terminales dealtavoz, puede daar la unidad.
Para evitar fallos de funcionamiento, no utilice los cables dealtavoz incorporados instalados en el automvil si su unidadcomparte un cable negativo comn () para los altavocesderecho e izquierdo.
No conecte los cables de altavoz de la unidad entre s.
Nota sobre la conexinSi el altavoz y el amplificador no estn conectadoscorrectamente, aparecer FAILURE en la pantalla. Si es as,compruebe la conexin de ambos dispositivos.
1
1Enganche
BUSAUDIOIN
L
R
AUDIOOUTREAR
L
R
REMOTE IN
AUDIO OUT REAR*2
3
2
4
AMP REM
ANT REM
7
Max. supply current 0.3 ACorriente mx. de alimentacin de 0,3 A 0.3 A
Fuse (10 A)Fusible (10 A)10 A
RedRojo
YellowAmarillo
BlackNegro
BlueAzul
WhiteBlanco
GreenVerde
PurpleMorado
White/black stripedCon rayas blancas y negras
Grey/black stripedCon rayas grises y negras
Green/black stripedCon rayas verdes y negras
Purple/black stripedCon rayas violetas y negras
GreyGris
3
LeftIzquierdo
Right
Derecho
LeftIzquierdo
RightDerecho
Max. supply current 0.1 ACorriente mx. de alimentacin de 0,1 A
0.1 A
1
5
*1
*1 RCA pin cord (not supplied)*2 AUDIO OUT can be switched to REAR
or SUB.For details, see the supplied operatinginstructions.
*3 Insert with the cord upwards
*1 Cable con terminales RCA (nosuministrado)
*2 AUDIO OUT (Salida de audio) puedecambiarse a REAR (Posterior) o SUB(Secundaria).Para obtener informacin, consulte elmanual de instrucciones suministrado.
*3 Insertar con el cable hacia arriba
*1 RCA
*2AUDIO OUT REAR SUB
*
3
*3
from car aerialdesde la antena del automvil
Blue/white stripedCon rayas azules y blancas
-
7/29/2019 Radio Sony CDX-3300s
3/4
182mm
53mm
Precautions
Choose the installation location carefully sothat the unit will not interfere with normaldriving operations.
Avoid installing the unit in areas subject todust, dirt, excessive vibration, or hightemperatures, such as in direct sunlight ornear heater ducts.
Use only the supplied mounting hardware fora safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45.
Removing the protection collarand the bracket (4)Before installing the unit, remove theprotection collar 5 and the bracket 1 fromthe unit.
1 Remove the protection collar 5.1Engage the release keys 6 together with
the protection collar 5.2Pull out the release keys 6 to remove the
protection collar 5.
2 Remove the bracket 1.1 Insert both release keys 6 together
between the unit and the bracket 1 untilthey click.
2Pull down the bracket 1, then pull upthe unit to separate.
Frequency select switchThe AM (FM) tuning interval is factory-set to the 9k (50 k) position. If the frequency allocation systemof your country is based on 10 kHz (200 kHz)interval, set the switch on the bottom of the unit tothe 10 k (200 k) position before making connections.
Mounting example (5)Installation in the dashboard
Notes
Bend these claws outwards for a tight fit, if
necessary (5-2). Make sure that the 4 catches on the protection
collar5 are properly engaged in the slots of the
unit (5-3).
Mounting the unit in a Japanese
car (6)You may not be able to install this unit in somemakes of Japanese cars. In such a case, consultyour Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
How to detach and attach thefront panel (7)Before installing the unit, detach the frontpanel.
7-A To detach
Before detaching the front panel, be sure topress (OFF). Press , then pull it off towardsyou.
7-B To attach
Attach part A of the front panel to part B of theunit as illustrated and push the left side intoposition until it clicks.
Warning when installing in a carwithout ACC (accessory)position on the ignition keyswitchAfter turning off the ignition, be sure to
press and hold (OFF) on the unit until thedisplay disappears.
Otherwise, the display does not turn off and thiscauses battery drain.
RESET button
When the installation and connections arecompleted, be sure to press the RESET buttonwith a ballpoint pen, etc., after detaching thefront panel.
4
1 2 3
5
1
1
Dashboard
Salpicadero
5
1 2
5
6 6
c c c
1
Face the hook inwards.
El gancho debe
encontrarse en la parte
interior.
Claws
Pestaas
Orient the release key
correctly.
Oriente la llave de
liberacin en la
direccin correcta.
Precauciones
Elija cuidadosamente el lugar de montaje deforma que la unidad no interfiera las funcionesnormales de conduccin.
Evite instalar la unidad donde pueda quedarsometida a altas temperaturas, como a la luzsolar directa o a conductos de calefaccin, o apolvo, suciedad o vibraciones excesivas.
Para realizar una instalacin segura y firme,utilice solamente las herramientas de montajesuministrada.
Ajuste del ngulo de montaje
Ajuste el ngulo de montaje a menos de 45.
Extraccin del marco deproteccin y del soporte (4)Antes de instalar la unidad, retire el marco deproteccin 5 y el soporte 1 de la misma.
1 Retire el marco de proteccin 5.1Una las llaves de liberacin 6 al marco de
proteccin 5.2Retire la llave de liberacin 6 para extraer
el marco de proteccin 5.
2 Retire el soporte 1.1 Inserte ambas llaves de liberacin 6 entre
la unidad y el soporte 1 hasta que encajen.2Presione el soporte 1 y, a continuacin,
levante la unidad para separar amboselementos.
Selector de frecuenciaEl intervalo de sintona de AM (FM) ha sido ajustadoen fbrica a la posicin 9 k (50 k). Si el sistema deasignacin de frecuencias de su pas se basa en elintervalo de 10 kHz (200 kHz), ponga este selector,situado en la base de la unidad, en la posicin 10 k(200 k) antes de realizar las conexiones.
Ejemplo de montaje (5)Instalacin en el salpicadero
Notas
Si es necesario, doble estas pestaas hacia fuera
para que encaje firmemente (5-2). Compruebe que los 4 enganches del marco de
proteccin5 estn bien fijados en las ranuras de la
unidad (5-3).
Montaje de la unidad en un
automvil japons (6)No podr instalar esta unidad en algunosautomviles japoneses. En tal caso, consulte a suproveedor Sony.
Nota
Para evitar que se produzcan fallos, realice la
instalacin solamente con los tornillos suministrados
4.
Forma de extraer e instalar elpanel frontal (7)Antes de instalar la unidad, extraiga el panelfrontal.
7-A Para extraerlo
Antes de extraer el panel frontal, asegrese depresionar (OFF). Despus presione y tire del hacia usted.
7-B Para instalarloColoque el orificio A del panel frontal en el ejeB de la unidad, como se muestra en lailustracin, y despus presione la parteizquierda.
Advertencia sobre la instalacinen un automvil que nodisponga de posicin ACC(accesorio) en el interruptor dela llave de encendidoTras apagar el motor, asegrese demantener presionado (OFF) hasta que
desaparezca la indicacin.
De lo contrario, la indicacin no se apagar y labatera se descargar.
Botn RESETCuando finalice la instalacin y las conexiones,asegrese de pulsar el botn RESET con un
bolgrafo, etc.
Fire wall
Cortafuegos
2
3
-
7/29/2019 Radio Sony CDX-3300s
4/4
OPEN
/EJEC
T
6 A TOYOTA
to dashboard/centre console
al salpicadero/consola central
Bracket
Soporte
Bracket
Soporte
B NISSAN
4
4
to dashboard/centre console
al salpicadero/consola central
Bracket
Soporte
BracketSoporte
4
4
Existing parts supplied with your car
Piezas existentes suministradas con su automvil
7 A B
max. size
5 8 mm
Tamao mx.
5 8 mm
58 mm
max. size
5 8 mm
Tamao mx.
5 8 mm
58 mm
max. size
5 8 mm
Tamao mx.
5 8 mm
58 mm
max. size
5 8 mm
Tamao mx.
5 8 mm
58 mm
OPEN/E
JECT
(OFF)
Existing parts supplied with your car
Piezas existentes suministradas con su automvil
45
4
5
1
1 51 6 5 2 6 5
2 11 6
1 2 1
AMFM 9 k50 k 10 kHz200 kHz 10 k200 k
5
5-2 5 4
5-3
6 Sony
4
7
7-A
(OFF)
7-B
A B
ACC
(OFF)
RESET
RESET