radio remote controls - danlers limited radio remot… · complete with 2m cable for quick and easy...

These products are used for the remote control switching or dimming of lighting or other loads. The wire-free senders are available as hand held or wall mounted versions.

A receiver switch or receiver dimmer is wired into the existing circuit to control the connected load. The sender signals can pass through walls or ceilings so the receivers can be mounted out of sight. Inside a typical building the receivers can work at an approximate range of 30-50 metres. In free air the range is approximately 100-150 metres. The carrier frequency of the radio signals is 868MHz, which is CE Approved and Licence Free.

an EXaMpLE buiLding

radio receivers

Wire-free radio senders12 channel hand sender to control ceiling lights, spot lights and screen. For security reasons a caretaker can use another 12 channel hand sender to control all the lights inside the building and the outside security lights.

All lights can also be controlled by wire-free wall mounted senders.

Exterior receiver switch for outside lights.

Display cabinet lamps or standard desk lamps can be controlled via a plug-in dimmer receiver.

Receiver switches and receiver dimmers for the lighting circuits can be concealed behind a false ceiling.

radio remote control senders and receivers

86 www.danlers.co.uk

radiO rEMOtE COntrOLS

Conventional glass: approx. 70-90% Insulating glass (with vaporised metal coat): approx. 30-60% penetration

Plastics: approx. 80-95% penetration

Metal walls: approx. 0-10% penetration

Reinforced concrete: approx. 20-60% penetration

Timber framework with sandwich plasterboards: approx. 80-95% penetration

Brick walls: approx. 60-90% penetration

The radio signals cannot pass through the entire length of walls.

The radio signals achieve a range of approximately 30-50m inside a building; 100-150m in free air.

radio remote control functions

Each button on each sender sends a unique coded signal (one of 4 billion codes). A simple set-up procedure enables any chosen receiver to respond to the signal from any chosen sender button. The sender button then controls the receiver (and its connected load). This simple procedure is repeated, creating links between various sender buttons and various receivers.

As shown, almost any control set-up is possible; from a single room to an entire building.

For the simplest set-up, one receiver can be controlled by one sender.

Any receiver can be programmed to respond to the unique coded signal from any sender button. Hence, a sender button can control any number of receivers simultaneously.

Receiver

Sender

Also a single receiver can be controlled by up to 15 sender buttons.

These control combinations can be mixed and matched, making it possible to have almost any control set-up desired; from the simplest single room to an entire building. In the above control set-up, one button on the left hand sender controls the first receiver. A different button on the left hand sender controls the first and second receivers simultaneously, and so on.

typical penetration of radio signals

telephone: +44(0)1249 443377 87


Radio remote control wire-free hand senders

12 channel hand held sender

Sends on 12 unique channels. Complete with two AAA batteries.

Specification

Signal range: Up to 150m in free air

Carrier frequency: 868MHz (CE Approved, Licence Free)

Dimensions: 152 x 54 x 20mm

order code: HASE 12RFC

Dimensions in mm

Also available: Slave senders See page 95 for details.

order code: HASE 2RF

2 channel key fob sender

Sends on 2 unique channels. Complete with CR2430 battery.With optional wall mounting fixing.

Specification




Dimensions in mm

16

side

46

86

front

20

side

54

152

front



Radio remote control wire-free wall senders

Specification



Dimensions in mm

front side

1587

87

Dimensions in mm

front side

1587

87

Dimensions in mm

front side

1587

87

All DANLERS radio remote control wall or hand senders operate on a carrier frequency of 868MHz (CE Approved, Licence Free).

Wire-free. No wall box needed.

Complete with CR2430 battery(ies).

Simple programming procedure.

Requires compatible DANLERS receiver switch or receiver dimmer to operate.

Wall senders can be wall mounted or mounted on other working surfaces using the supplied adhesive strips or screwed to a fixed surface via the surface mounting plate behind the clip on front plate.

Also available: A range of different colours and finishes are available on request. Please ask for details.

WASE 1RF WHI Sends on 1 unique channel.


WASE 2RF WHI Sends on 2 unique channels.


WASE 4RF WHI Sends on 4 unique channels.


telephone: +44(0)1249 443377 89


order code: WASE 1RF WHI



Wall or ceiling mounted switch: WACE RFS

Hard wired. Can be mounted on a 16mm box.Can be mounted out of sight.

Specification

Loading: Up to 6 amps (1500W) of resistive load or up to 1 amp (250W) of transformer or fluorescent load

Wiring diagram: See diagram below


order code: WACE RFS

order code: DIN RFS

Dimensions in mm

DIN rail receiver switch: DIN RFS

For fixing on to either 35 x 7.5mm top-hat DIN rail or 32 x 15mm g-type DIN rail.

Specification




DIN rail receiver dimmer also available on request.

Radio receiver switches

order code: CERF S6ARequires socket, order code: CESO or CESO SQ (see page 94)

Dimensions in mmPlug-in switch: CERF S6A

Plugs into a Ceiling socket (shown on p.94).Can be mounted out of sight.

Specification

Loading: Up to 6 amps (1500W) of any type of load, including fluorescent lights or up to 1 amp (250W) of fans



57

side

72

130

plan

Dimensions in mm

plan side

22 86

86

order code: CEFL RFS

order code: CEVO RFS

Ceiling flush mounted switch: CEFL RFS

Complete with 2m cable for quick and easy installation. Loading and wiring as for WACE RFS.

Dimensions: 72mm diameter x 68mm (requires 63mm diameter hole)

Hard wired switch: CEVO RFS

Complete with 2m cable for quick and easy installation. Ideal for ceiling voids. Will fit through a 63mm diameter aperture. Loading and wiring as for WACE RFS.

Dimensions: 60mm diameter x 130mm

Also available: Hard wired switch: CEVO RFS6AComplete with 2m cable for quick and easy installation. Loading and wiring as CERF S6A.


35

side

75

100

plan

Lreceiver switch

load

N

230 VAC

Remote control switching

wire-free sender

SL

Wiring diagram



order code: DIN RFS

order code: CERF S6A

Plug-in adaptor switch: PORF S8A

Plugs into a UK 3-pin mains socket and has its own 3-pin socket for a mains powered plug-in device. Ideal for table lamps or displays.

Specification


Wiring: Plugs into 13 amp mains socket


order code: PORF S8A

order code: EXRFS

order code: WACE RF2S

Dimensions in mm

Exterior switch: EXRFS

Hard wired. outdoor mounted. Weatherproof to IP65 rating.

Specification


Wiring diagram: See diagram A below


Dual momentary switch: WACE RF2S

Hard wired. Wall or ceiling mounted. Twin actuator switch. Enables blinds to be opened, closed or adjusted to any position required. Can be mounted on a 16mm box. Can be mounted out of sight.

WACE RF2S can also be used as a slave to control up to two DANLERS grid time lag or soft start dimmer switches. This can allow RF control of higher wattage loads including toroidal transformers.

Radio receiver switches

Dimensions in mm

Dimensions in mm

side

98

front

35

64

side

60

138

front

48

A. Remote control switching

DownMotor

UpMotor

Contactor

Contactor

WACE RF2S

SL2

SL1L

N

L

NN

L (high current)

230 VAC

wire-free sender

B. Blind/motor control switch

Lreceiver switch

load

N

230 VAC

wire-free sender

L

N

wire-free sender

soft start dimmer

WACE RF2S

load

230 VAC

C. Soft start dimmer with remote control

plan side

22 86

86

Specification


Wiring diagram: See diagrams B and C below


SL

SLL

V

S

Wiring diagrams

telephone: +44(0)1249 443377 91


order code:

order code:

Wall or ceiling mounted dimmer: WACE RFD250W

Hard wired. Can be mounted on a 16mm box.Can be mounted out of sight.

Specification

Loading: Up to 250W of resistive, mains halogen* or dimmable electronic transformer loads

Dimming technology: Trailing edge

Wiring diagram: See diagram A on page 93


Radio receiver dimmers (trailing edge)

order code: WACE RFD250W

Dimensions in mm

order code: EXRF D250W

Exterior dimmer: EXRF D250W

Hard wired. outdoor mounted. Weatherproof to IP65 rating.

Specification



Wiring diagram: See diagram A on page 93


Dimensions in mm

151

34

plan

side

151

28

side

60

138

front

48

side

98

front

35

64

28

59

front side

30

38

28

59

front side

34

48

front side

12

86

86

plan side

22 86

86

*Mains halogen lamps must have an integral thermal safety fuse.

order code: CEFL RFD250W

order code: CEVO RFD250W

Also available: Ceiling flush mounted dimmer: CEFL RFD250W

Complete with 2m cable for quick and easy installation. Loading and wiring as for WACE RFD250W.

Dimensions: 72mm diameter x 68mm (requires 63mm diameter hole)

Also available: Hard wired dimmer: CEVO RFD250W

Complete with 2m cable for quick and easy installation. Ideal for ceiling voids. Will fit through a 63mm diameter aperture. Loading and wiring as for WACE RFD250W.


Plug-in adaptor dimmer: PORF D250W

Plugs into a UK 3-pin mains socket and has its own 3-pin socket for a mains powered plug-in device. Ideal for table lamps or displays.

Specification



Wiring: Plugs into 13 amp mains socket


order code: PORF D250W

Dimensions in mm

side

60

138

front

48



order code: PORF D250W

order code: WACE RFD250W

Radio receiver dimmers (trailing edge)

Lreceiver dimmer

loadwire-free sender

230 VAC

A. Remote control dimming

N

B. CERF D10VDC MB controlling several 1-10VDC dimmable ballasts

wire-free sender

L

N

1ballast

10

1ballast

10

1ballast

10

230 VAC

CERF D10VDC MBcontrol lines

order code: CERF D10VDC MB

Build-in dimmer: CERF D10VDC MB

Ideal for building into a luminaire or gear tray. For controlling dimmable ballasts with a 1-10VDC analogue input.

Specification

Loading: Up to 6 amps (1500W) of resistive load or up to 4 amps (1000W) of fluorescent load. Total load of ballasts, lamps plus other loads not more than 2 amps.Can control up to 20mA, eg. 20 ballasts at 1mA.

Dimming technology: 1 to 10V with relay off

Wiring diagram: See diagram B below


Dimensions in mm

151

34

plan

side

151

28

Build-in dimmer: CERF D500W GT

Ideal for building into a luminaire or gear tray. Hard wired build-in dimmer.

Specification

Loading: Up to 500W resistive, mains halogen* or dimmable electronic transformer loads




Dimensions in mm

151

34

plan

side

151

28

order code: CERF D500W GT

order code: CERF D500WRequires socket, order code: CESO or CESO SQ (see page 94)

Dimensions in mm

Plug-in dimmer: CERF D500W

Plugs into a Ceiling socket (shown on p.94).Can be mounted out of sight.

Specification





57

side

72

130

plan Dimensions in mm

*Mains halogen lamps must have an integral thermal safety fuse.

VSL

Wiring diagrams

telephone: +44(0)1249 443377 93


Ceiling socket: CESO

For DANLERS plug-in switches or dimmers. Can be mounted on a BESA box.

Specification



Also available as a square socket.

Ceiling socket: CESO SQ

Can be mounted on a square pattress box.



order code: CESO

order code: CESL

Sockets and slave relays

A. Ceiling mounted socket (CESO or CESO SQ) for plug-in ceiling controls

L N SLplug-in ceiling control Not to scale

CESo orCESo SQ

BESA box or pattress box

luminaire

L N

SL

Dimensions in mm (CESO)

L1

N1

CE2SLplus plug-in switch

separate circuit

optional manual wall switch for overriding off

SL1

load230 VAC

SL2N/o

SL2N/C

SL3N/o

SL3N/C

C3C2

separate circuit

C. Plug-in control plus double slave relay with volt free changeover contacts (CE2SL) controlling two extra circuits

L1

SL2N/C

N1

CESLplus plug-in switch

separate circuit

optional manual wall switch for overriding off

230 VAC load

SL1

SL2N/o

C2

B. Plug-in control plus slave relay with volt free changeover contacts (CESL) controlling one extra circuit

Ceiling slave relay: CESL

For DANLERS plug-in switches only. Provides an extra 1-pole isolated changeover contact. Enables the switching of an additional circuit with its own supply, e.g. the corridor lights outside an office or a separate low voltage control circuit.

Specification

Loading: (Each circuit) up to 6 amps (1500W) of resistive, fluorescent or transformer lighting loads, or up to 1 amp (250W) of fans

Wiring diagram: See diagram B below


order code: CE2SL

Dimensions in mmCeiling double slave relay: CE2SL

For DANLERS plug-in switches only. Provides extra 2-pole isolated changeover contacts. Enables the switching of two additional circuits, each with its own supply, e.g. the corridor lights outside an office and the extractor fans inside the office. Also ideal for switching two separate low voltage control circuits.

Specification

Loading: (Each circuit) up to 6 amps (1500W) of resistive, fluorescent or transformer lighting loads, or up to 1 amp (250W) of fans

Wiring diagram: See diagram C below


Dimensions in mm

plan side

41

87

87

87

plan side

41

87

87

87

order code: CESO SQ

plan 74

side 74

13

CESO

Dimensions in mm (CESO SQ)

plan side 13 87

87

CESO SQ

Wiring diagrams



order code: CESO

For use with DANLERS plug-in switches, such as PIR occupancy switches or Photocell switches. For controlling other remote circuits via Radio receiver switches or dimmers (shown on pages 90 to 93).

The SLSE 1RFSo is hard wired. Requires mains power supply. Sends on 1 unique channel. For programming, requires Test plug (order code TEPL).

Dimensions in mm

plan side

4187

87

Specification




Radio slave sender and radio receiver

L

DANLERS plug-in switch

230 VAC

SLSE 1RFSo

N

L1Radio receiver

load

230 VAC

N1

Slave radio senders

order code: SLSE 1RFSO

Also available on request: Outdoor 2 channel slave radio sender (order code: EXSLSE 2RF).

By special order DANLERS can supply packages of Senders and Receivers which are factory pre-programmed to perform specified special switching and/or dimming functions. The table lists some of the special functions that are available, plus examples of how these functions may be used.

Even packages which perform several different functions can be supplied.

Please note there is an additional charge to customise for special requirements and a charge for programming on site.

Please call to discuss your particular requirements.

Special switching function Example application

Time delay oN For a special stage effect

Time delay oFF A courtesy light for leaving a building

Time delay oFF with warning Demand for lighting for few minutes in a stock cupboard, with flashing prompt to re-press the sender before the lights go out

Momentary oN To sound a doorbell

Flashing To give an alert signal (e.g. testing in progress)

Motor control To open and close blinds, screens or shutters

Customised functions and scene-setting

Wiring diagram

telephone: +44(0)1249 443377 95


radio remote controls - danlers limited radio remot… · complete with 2m cable for quick and easy...

Documents