Step 7 While turning on the display device the HD Flow Pro Wireless Multimedia units will be going through the startup process. This process may take up to two minutes to complete. The Power/Link indicator lights on the Transmitter and the Receiver will be flashing at first. Flashing indicates that the units are establishing a secure connection. Wait until the connection is successfully established, indicated by the Power/Link indicator light becoming solid.

Minutes2

1 x Transmitter

1 x Receiver

2 x Stand

1 x Remote Control

1 x IR Flasher

1 x IR Extender

1 x Component Adaptor

2 x Power Adapter

1 x Quick Start Guide

1 x Users Manual

Step 2 Connect the provided IR Flasher to the IR-OUT port on the Transmitter. Find the location of the IR window on your source device and adhere the IR Flasher eye directly over the IR window on your source device. Note: One IR Flasher eye is to be used for one component device.

Step 4 Install the IR Extender by plugging in the provided IR Extender in to the IR-IN port on the Receiver and adhering the other end of the IR Extender to a vertical surface near the output device. Ensure that the IR Extender is in a line of sight to the remote control that controls your source devices. Note: For Multicast models, receivers two, three and four do not come with an IR Extender. Additional IR Extenders (HDS-IRE) can be purchased separately; visit peerless-av.com for more information.

Step 6 Turn on your display device (TV, monitor, projector, etc.).

Step 3 Connect the display device (TV, monitor, projector, etc.) to the Receiver.

Step 5 Power-up the HD Flow Pro Devices.1. Plug in the power adapter for the Transmitter and the Receiver to nearby available power outlets.2. Plug in the power adapter end to the Transmitter and then to the Receiver.3. The units will automatically turn-on. The average power-on/sync time is approximately two minutes.

What’s in the Box

Installation and Setup

troubleshooting tips

Tip The IR window may be easier to locate with a direct light shining on sections of the front panel of the component device. A small flashlight works well.

Power/Source Selection Button

Tip Repeat Steps 3-11 to connect more than one Receiver unit (HDS200-2, HDS200-3, HDS200-4).

Step 1 Connect the Transmitter to the source devices (Blu-ray™ Disc player, set top box, gaming console, etc.).

Step 9 Turn on the desired source device that is connected to the Transmitter.

Step 11 Play the source device content and enjoy up to Full HD 1080p wireless entertainment experience.

• Check the media source resolution. The display device must be able to support the resolution of the media source that is being streamed. Utilizing the INFO button will allow you to see the resolution data that the display device supports. If the display device supports the highest resolution of 720p but the source device is outputting 1080p content, the content needs to be down-scaled to the maximum resolution of the display device, in this case 720p.

Receiver output Indicator Light Blinks:

• Make sure that your display device, source device and the HD Flow Pro units are all turned ON and the Receiver is properly connected to the output device.

• Verify that the Receiver is set to the appropriate output port.

• Check the resolution setting of your source device. This may need to be changed to a resolution supported by the HD Flow Pro unit. Reference the Resolution Chart in the HD Flow Pro Manual for compatibility. Reference your source devices’ manual for instruction on changing the output resolution.

If the above troubleshooting tips do not resolve the issues for a unicast setup, please reference the Factory Reset Section of the HD Flow Pro Manual. For a multicast system configuration, please contact Peerless-AV Customer Care at 800-856-2112 for further instruction.

Step 8 Select the output that connects the Receiver to the display using the Power/Source Selection Button or the provided remote control. The output indicator light will become solid and the HD Flow logo will appear on the display device.

Step 10 Select the desired source or device input on the Transmitter using the Power/Source Selection Button on the remote control.

transmitter and/or Receiver Indicator Lights are all Blinking:• The HD Flow Pro units are establishing a connection. It can take

up to two minutes for the HD Flow Pro units to establish a complete connection. If after two minutes have passed and the units have not established a connection, unplug the power cable, wait 30 seconds and reconnect the power supply to the units.

transmitter or Receiver Power Indicator Light is oFF:• Check and verify the power supply connection.

transmitter Input Indicator Light Blinks:• Make sure that your source device is turned ON and the cable

is properly connected.

• Verify that the Transmitter is set to the appropriate input port.

• Check the resolution from your source device. This may need to be changed to a resolution supported by the HD Flow Pro Wireless Multimedia Kit. Reference the Resolution Chart in the HD Flow Pro Manual for compatibility. Reference your source devices’ manual for instruction on changing the output resolution.

Receiver Power Indicator Light Blinks:• Verify that the HD Flow Pro Transmitter and Receiver are within

the recommended range of 131 feet. Physical obstructions such as walls, floors and ceilings between the Transmitter and Receiver may decrease the strength of the connection signal and reduce the overall transmission range.

If a connection has been established and the HD Flow logo can be seen on the display device, but content is not playing:• Make sure that the input/output cables are properly connected.

• Verify that the Transmitter is set to the appropriate input port.

Warning Do not place the HD Flow Pro units near other devices that emit excessive amounts of heat. Increased temperatures may cause the HD Flow Pro Transmitter or Receiver unit to malfunction or stop working.

Quick Start Guide for HD Flow Pro Wireless Multimedia Kit - LIT-0906

Power/Source Selection Button

© 2012 Peerless Industries, Inc. Peerless-AV™ is a trademark of Peerless Industries, Inc. All rights reserved.

HD Flow™ is a trademark of I Do It, LTD. Other parties’ marks are the property of their respective owners. hdflow.com

Quick Start GuidePRO WIRELESS MULTIMEDIA KIT Model No. HDS200 (-2, -3, -4)

READY

®