questionnaire primary flow elements - euromisure · questionnaire primary flow elements customer...
TRANSCRIPT
09/2018 Page 1 of 3
Flow measurement
QuestionnairePrimary flow elements
Customer data
CompanyName
Address
DatePhoneE-mail
Plant or project Tag no.
WIKA reference quotation
Fluid
Single-phase Multi-phase
Liquid
Gas
Steam
Gas/liquid ratio (in %): Volume Mass
Density (at operating conditions): kg/m³ lb/ft³Viscosity: cP cST
MW: Cp/cv: SG:Compressibility factor: Viscosity: cP cST
Superheated Saturated, dry Saturated, wet (water content 0 ... 5 %) %
Minimum Normal Maximum Full scale Units
barg psig mmH2Og °C °F
Schedule or WT Nominal pressure rating Pipe MaterialNominal sizeSealing face: Raised face (RF) Flat face (FF) Ring-type joint (RTJ)
Commercial information
Fluid characteristics
Process data
Pipeline and piping class
Origin of Material
Competitors
Target price € $(Please specify amount)
Flow rate Pressure Temperature Design pressure Design Temperature
No restriction With restriction (e.g. no China, India, ecc.)Please specify
Amount:
Other:
Design: Square edge
Page 2 of 309/2018
Pressure taps: Flange taps Corner taps
Tappings: ½" NPT ½" SWMaterial of nuts and studs:
Pressure taps: Corner taps Flange tapsTappings: ½" NPT ½" SW Other:Material: Stainless steel 316/316L Other:Process connection: Butt welded Flanged 1)
Design: ISA 1932 Long radiusTappings: ½" NPT ½" SW Other:
Number of pressure taps:
Material: Stainless steel 316/316L Other:Mounting option, ISA 1932: With flanges Without flangesProcess connection, Long radius: Butt welded Flanged 1)
Design: From bar Welded sheetMaterial: Stainless steel 316/316L Carbon steel Other:
Exit cone: 7° 15° Other: Truncated
Tappings: ½" NPT ½" SW Other:
Flanged Dimensions:
Number of pressure taps: Process connection: Butt welded Flanged 1)
Mounting types: Compression fitting Flanged version Extractable versionVariants (series): 73 75 78
End support: No Yes
Design: Square edge Quarter circle Eccentric Conical entranceMaterial: Stainless steel 316/316L Other:Drain hole, vent hole: None Drain hole Vent hole
Orifice flange Orifice assembly (orifice plate and orifice flange)
Flow nozzle
Meter run Integral orifice
Pitot tube (FloTec)
Venturi tube
Orifice plate
Model of primary flow element
1) Flange rating and sealing face see “Pipeline and piping class” (page 1)
Compact orifice
Conical entranceAccessories: 3-way valve manifold 5-way valve manifold
Temperature probe
Body material:
Wedge material:
Pressure taps:
Process connection:
09/2018 Page 3 of 3
WIKA Alexander Wiegand SE & Co. KGAlexander-Wiegand-Straße 3063911 Klingenberg/GermanyTel. +49 9372 132-0Fax +49 9372 [email protected]
1) Flange rating and sealing face see “Pipeline and piping class” (page 1)
Wedge Meter
Model of primary flow element
OtherOther
Stainless steel 316/316L Stainless steel 316/316L
Carbon steelCarbon steel
2"
Butt welded
3"
Cone Meter
OtherOther
Stainless steel 316/316L Carbon steel
1/2" NPT
Body material:
Cone material:
Pressure taps:
Process connection: Butt welded
1/2" SW Stainless steel 316/316L
Other
Flanged 1)
Flanged 1)