quantum wiring extension-rf - continal

5
UNDERFLOOR HEATING Quantum wiring extension-RF Contents 1. Wiring diagram 2. Pairing thermostats with the Quantum wiring extension-RF 3. Installation 4. LED indications 5. Product compliance and safety information Simple to operate and easy to install, our Quantum wiring extension-RF increases the capabilities of your Quantum wiring centre-RF. This plug-in unit allows you to attach up to 4 more thermostats, using simple push- in connectors. Super-clear LEDs keep you in the picture.

Upload: others

Post on 31-Jan-2022

1 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Quantum wiring extension-RF - Continal

U N D E R F L O O R H E A T I N G

Quantum wiring extension-RF

Contents1. Wiring diagram2. Pairing thermostats with the Quantum wiring extension-RF3. Installation4. LED indications5. Product compliance and safety information

Simple to operate and easy to install, our Quantum wiring extension-RF increases

the capabilities of your Quantum wiring centre-RF.

This plug-in unit allows you to attach up to 4 more thermostats, using simple push-

in connectors. Super-clear LEDs keep you in the picture.

Page 2: Quantum wiring extension-RF - Continal

U N D E R F L O O R H E A T I N G

1. Wiring diagram

2. Pairing thermostats with the Quantum wiring extension-RF

Pairing thermostats should be done using the Quantum wiring centre-RF where the Quantum coordinator is connected. If you connect the Quantum wiring extension-RF to the Quantum wiring centre-RF on first installation, all of the thermostats on both the wiring centres will be automatically paired. If you connect the Quantum wiring extension-RF to the Quantum wiring centre-RF after the thermostats have been paired, you must pair thermostats with the Quantum wiring extension-RF.

To do this:

1. Turn off the power to the Quantum wiring centre-RF

2. Connect the Quantum wiring extension-RF to the Quantum wiring centre-RF

3. Power on the Quantum wiring centre-RF and the Quantum wiring extension-RF

4. Remove the front cover of the Quantum wiring centre-RF and press and hold the coordinator button for five seconds

5. Pair the thermostats in zones 9 to 12

6. Press and hold the Quantum coordinator button again for five seconds

7. Replace the front cover of the Quantum wiring centre-RF

GROUP 2

GROUP 2THERMOSTAT

(VS20WRF)

GROUP 2THERMOSTAT

(VS20WRF)

GROUP 2THERMOSTAT

(VS10WRF)

GROUP 2THERMOSTAT

(VS10WRF)

SUPPLIED CABLES

UNDERFLOOR HEATING MANIFOLD

NL

Page 3: Quantum wiring extension-RF - Continal

U N D E R F L O O R H E A T I N G

Device

Power50mm

110mm

10mm

10mm

3. Installation

Remove the white terminal connection board.Remove the plastic cover. Open the four white screws with a quarter turn only.

Attach the back of the Quantum wiring extension-RF to the DIN rail or wall. If you are fitting to the side, use the short ribbon cable. Otherwise, use the long ribbon cable (see step 10). The following shows the side-mounted, wall installation:

Cut the power and device cables to length.

Device

Power

50mm

110mm

10mm

10mm

1 2

3 4

Replace the white connection board. Insert the power wires.

5 6

Attach the white strain-relief using the two screws to secure the power wires.

Push the actuator wires into the holes at the bottom of the wiring extension-RF. You can connect up to four actuators in each zone.

7 8

Page 4: Quantum wiring extension-RF - Continal

U N D E R F L O O R H E A T I N G

Attach the short ribbon cable between the Quantum wiring centre-RF and the Quantum wiring extension-RF for side installation, otherwise use the long ribbon cable.

Remove the plastic cover from the Quantum wiring centre-RF.

Push out the cut out on the bottom of the cover of the Quantum wiring extension-RF.

Replace the plastic cover.

Switch on the mains power supply to the unit. The red LED comes on.

9 10

11 12

13

Page 5: Quantum wiring extension-RF - Continal

U N D E R F L O O R H E A T I N G

5. Product compliance and safety information

Product complianceThis product complies with the essential requirements and other relevant provisions of the following EU Directives: EMC 2014/30/EU, Low Voltage Directive LVD 2014/35/EU and RoHS directive 2011/65/EU.

Safety informationUse in accordance with national and EU regulations. Device is intended for indoor use only in dry conditions. Installation must be carried out by a qualified person in accordance with national and EU regulations.

Before attempting to setup and install, make sure that the devices are not connected to any power source. Installation must be carried out by a qualified person. Incorrect installation may cause damage to the devices. The Quantum wiring extension-RF should not be installed in areas where it may be exposed to water or damp conditions.

4. LED indications

Name Colour Meaning

Connection • Quantum wiring extension-RF is connected to the Quantumwiring centre-RF

Power • Quantum wiring extension-RF is supplied with 230VAC power

Zone 9 actuators • Demand from zone 9 thermostat, actuator open

Zone 10 actuators • Demand from zone 10 thermostat, actuator open

Zone 11 actuators • Demand from zone 11 thermostat, actuator open

Zone 12 actuators • Demand from zone 12 thermostat, actuator open

Want more information?0333 800 1750

www.continal.co.uk

Rev:11/21© 2021 Continal Group Ltd. All rights reserved. E & OE.