qm03 16 calibration

29
Testing: Unit Testing / User Manual Module: Quality Management ENVIRONMENT SYSTEM : SAP R/3 ECC 6.0 CLIENT : 200 UNIT TESTING SCENARIO SCENARIO NUMBER : BPML QM03-16 DESCRIPTION : GAUGE CALIBRATION PREPARED & TESTED BY NAME : JL Hatekar SIGNATURE : DATE : TEAM : Approved By : Kabir R (PwC) Page 1 of 29

Upload: asifsayed

Post on 04-Sep-2014

51 views

Category:

Documents


1 download

DESCRIPTION

CALIBERATION

TRANSCRIPT

Page 1: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

ENVIRONMENT

SYSTEM : SAP R/3 ECC 6.0

CLIENT : 200

UNIT TESTING SCENARIO

SCENARIO NUMBER : BPML QM03-16

DESCRIPTION : GAUGE CALIBRATION

PREPARED & TESTED BY

NAME : JL Hatekar

SIGNATURE :

DATE :

TEAM :

Approved By : Kabir R (PwC)

Page 1 of 29

Page 2: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

1. Transaction Code/ Path

Enter the menu path of the transaction code, which is going to be tested by the user.

Menu Path Logistics - CreateT.Code IP11

2. Input Data

1. Enter the Input parameters, which need to be given by the user during the testing of this scenario.

2. Input the value for the fields and then if required, copy the screen shot of the input screen after the table.

3. If the scenario has multiple screen inputs, which needs to be processed, repeat the step 2 for every screen.

2.1 Input Screen Name – Create Sales Order: Initial Screen

Description of the Field

Nature of the Field Value of the Field

Order Type Mandatory

Select New entries

Page 2 of 29

Page 3: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Select Packages

Click “New Entry” And make the entries as per requirement in respective columns as shown below

Page 3 of 29

Page 4: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Save the data . Strategy 3_5_7days created.

END

Page 4 of 29

Page 5: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality ManagementTO CREATE CALIBRATION TASK LIST

Menu Path Logistics - CreateT.Code IA05 / 06

ENTER

GO TO “OPERATION “, TYPE CONTROL KEY – QM01 AND OPERATION DESC.

Page 5 of 29

Page 6: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

GO TO “MntPack” AT BOTTOM MENU

Tick the required calibration frequency and Go to “Insp. Char”at bottom menu and click

Page 6 of 29

Page 7: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Select the MIC by drill down or Select Quant. / Qual. Characteristics, type Short text of Insp Char. And go to “Control Indicator” and tick required data as shown in below screen and tick

Page 7 of 29

Page 8: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality ManagementClick on tick , following screen will display. Drill down on selected set as it is Qualitative Inspection char.

Click on “selected set selection” following screen will display

Page 8 of 29

Page 9: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality ManagementSelect the “selected set “ and click on tick following screen will display.

Also select the defect catalog and code group and ENTER

Select the sampling scheme from drill down. Enter, following screen will display.

Page 9 of 29

Page 10: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Similarly for Quantitative char. –Tick on Quant. And type desc, select the line and go to control indicator. And select the required function as shown in following screen.

Click on tick,

Page 10 of 29

Page 11: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Click on tick, enter the required values as shown in following screen.

Enter and select the “Sampling procedure” from drill down

Page 11 of 29

Page 12: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Enter, following screen will display

Select both the lines and SAVE.------------------------------------------------------------------------------------------------------------CREATE MAINTENANCE PLANMenu Path Logistics - CreateT.Code IP42 / 02/ 03

Page 12 of 29

Page 13: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Select Maint. Plan. Cat. As PM Maintenance Order and select the strategy from drill down.

Enter

Page 13 of 29

Page 14: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Half portion of above screen as given below

Page 14 of 29

Page 15: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Go to “Maint. Plan scheduling parameters” tab enter, enter Call horizon, Scheduling period, tick completion requirement, Start of cycle.

Page 15 of 29

Page 16: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Page 16 of 29

Page 17: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Click on next screen will display

Tick of Equipment task list if the task list is created for an equipment or tick on Gen. task if the task list is created for general ( All items same) & execute. Following screen will display.

Page 17 of 29

Page 18: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Save and following screen will display, and Created maintenance plan No. will display at bottom of Screen ( Here it is 151)

Page 18 of 29

Page 19: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

To created Scheduling – T code – IP10Enter maintenance Plan, Hit Enter

Page 19 of 29

Page 20: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Click of “Start” date of start of cycle will display or give date of start of cycle

Click on Tick, calibration cycle sill display.

Page 20 of 29

Page 21: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Save to start the Cycle, the Inspection lot / Order will get created.To check inspection lot – T code –QA32, The schedule call can be seen from IP24, to see the Order – T code – IW33

To see Inspection lot – T code—QA32

Page 21 of 29

Page 22: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Execute,

List of inspection lot will get display. To see the Schedule calls – T code – IP24 ( Use Variant /PM)

Page 22 of 29

Page 23: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Page 23 of 29

Page 24: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality ManagementExecute , -- Work order 4000502 is created.

Order can be seen from T Code -- IW33Give order No. – 4000502

Enter

Page 24 of 29

Page 25: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Go to “Operation Tab”

END

Page 25 of 29

Page 26: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Page 26 of 29

Page 27: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Page 27 of 29

Page 28: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Page 28 of 29

Page 29: QM03 16 Calibration

Testing: Unit Testing / User Manual Module: Quality Management

Page 29 of 29