pv training manual
TRANSCRIPT
-
8/11/2019 Pv Training Manual
1/53
Training Manual
Photovoltaic System
Green Empowerment Palang Thai
In coordination with
Karen Health and Welfare Department
Taipei Overseas Peace Service, Thailand
Zoa Refugee Care
-
8/11/2019 Pv Training Manual
2/53
Table of Contents
1.0 Introduction ---------------------------------------------------------------------------------4
1.1 Summary of Components-----------------------------------------------------------------5
2.0 How a Solar Panel Works----------------------------------------------------------------6
3.0 Basic Power Terms-------------------------------------------------------------------------7
3.1 The Difference Between DC and AC-----------------------------------------------------7
3.2 Power That a Solar Panel Produces-----------------------------------------------------8
3.3 Watts VS Watt-Hours------------------------------------------------------------------------9
4.0 The Sun as a Resource-------------------------------------------------------------------10
4.1 Perfect Sun Hours---------------------------------------------------------------------------10
4.2 Orientation-------------------------------------------------------------------------------------13
5.0 How Solar Panels Function------------------------------------------------------------14
5.1 IV Curves--------------------------------------------------------------------------------------15
5.2 Changes in IV Curves----------------------------------------------------------------------16
6.0 The Charge Controller-------------------------------------------------------------------17
7.0 Wiring-------------------------------------------------------------------------------------------18
7.1 Terminations-----------------------------------------------------------------------------------18
7.2 Wire Sizing-------------------------------------------------------------------------------------18
8.0 Batteries---------------------------------------------------------------------------------------21
8.1 Types of Batteries----------------------------------------------------------------------------22
8.2 Depth of Discharge--------------------------------------------------------------------------23
8.3 State of Charge ------------------------------------------------------------------------------23
8.4 Battery Safety---------------------------------------------------------------------------------24
9.0 Inverters---------------------------------------------------------------------------------------25
2
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Table of Contents
-
8/11/2019 Pv Training Manual
3/53
10.0 Designing a PV System------------------------------------------------------------------26
10.1 Calculating Total Daily Consumption in Watt-hours---------------------------------27
10.2 Efciency of PV System--------------------------------------------------------------------28
10.3 Sizing the Panel------------------------------------------------------------------------------3110.4 Sizing the Battery----------------------------------------------------------------------------33
11.0 System Installation-------------------------------------------------------------------------35
11.1 Parallel and Series---------------------------------------------------------------------------35
11.2 Installation of the Solar Panel-------------------------------------------------------------37
11.3 Controller Installation------------------------------------------------------------------------40
11.4 Installation of the Battery-------------------------------------------------------------------41
11.5 Wiring Installation----------------------------------------------------------------------------41
11.6 Light Switch Installation--------------------------------------------------------------------42
11.7 Load Connections---------------------------------------------------------------------------42
12.0 Load Management-------------------------------------------------------------------------43
13.0 Trouble Shooting---------------------------------------------------------------------------46
13.1 Wire Connections----------------------------------------------------------------------------47
13.2 Battery------------------------------------------------------------------------------------------47
13.3 Solar Panel------------------------------------------------------------------------------------48
13.4 Check Load Terminals----------------------------------------------------------------------48
14.0 About Us--------------------------------------------------------------------------------------49
3
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Table of Contents
-
8/11/2019 Pv Training Manual
4/53
1.0 Introduction
This book is designed to be used as a manual for the training of how to design, install and maintain photovol-
taic (solar panel) systems. It is not made to stand alone as a book that a person reads on their own. Rather, this
book is more of a workbook that can be used to help in the training of those who will be installing and using
the system. Furthermore, the goal of this manual is not to go in depth into all of the intricacies of photovoltaic
systems, but rather provide the student with the practical information so that he or she will nish the training
with knowledge on how to troubleshoot and maintain their PV system. Finally, we hope that this workbook will
be a useful resource in the future when the trainees are called upon to maintain, troubleshoot, design or install a
system.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Introduction
-
8/11/2019 Pv Training Manual
5/53
1.1 Summary of Components
A. Solar Panel - Converts sunlight to electricity.
B. Batteries - Store electricity.
C. Charge Controller - Manages the ow of electricity between the solar panel battery and load.
D. Inverter - Converts DC power from the solar panel and battery to AC power. Inverters are notalways used. When they are used they can be combined with the same piece of equipment at
the charge controller
E. Load - Application for electricity, e.g. lights, LED light, computer, radio.
F. Wires - Connect the other various components together.
(A)
(B)
(C)
(C) (D)
(E)
(F)
(A)
(B)
(F)
(E)
(E)
5
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Introduction
-
8/11/2019 Pv Training Manual
6/53
2.0 How a Solar Panel Works
The solar panel only creates electricity when there is sun. The below picture depicts that when it is sunny the
solar panel captures the energy from the sun and converts it into electricity and turns on the light. When there is
no sun, the panel does not make electricity and there is no light.
This is the most simplistic type of solar panel system. In Fig. 3, the light will only work when there is enough
sun for the solar panel to produce electricity.
A loadis a piece of electri-
cal equipment that consumes
energy. For example, when
a light bulb is on it is a load
because it is consuming en-
ergy through electric wire
it is connected to.
6
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - How a Solar Panel Works
-
8/11/2019 Pv Training Manual
7/53
3.1 The difference between DC and AC
There are two types of electricity: direct current electricity (DC) and alternating current electricity (AC). Alter-
nating current is the type of current most commonly used in households that are connected to the grid to power
loads such as, radios, TVs, refrigerators, and lighting.
Direct current is used mostly in houses that are not connected to the grid, and are running off of batteries.
A solar panel produces DC electricity, and a battery stores DC electricity. Fig. 4a shows a diagram of direct cur-rent, where the current does not change. Alternating current electricity turns on and off 60 times a second.
Current is the ow of the
electricity through a wire.
Figure 4. AC VS. DC Electricity.
(a) Direct Current (b) Alternating Current (WWF - Energy & Galapagos)
7
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Basic Power Terms
-
8/11/2019 Pv Training Manual
8/53
-
8/11/2019 Pv Training Manual
9/53
A wattis the amount of power that asolar panel can produce or that a lightbulb consumes.
3.3 Watts vs. Watt-Hours
A watt-houris the amount of energythat a solar panel can produce or alight bulb can consume in a certainnumber of hours.
Watt Hours = Watt X # of Hours
Power= Watts Energy= Watt-Hours
For example, a 13 watt light bulb requires power of 13 watts to light up.
If a 13 watt light bulb is lit for 3 hours, it consumes energy of 13 watts X 3 hours or 39 watt-hours:
13 Watts X 3 Hours = 39 Watt-Hours
9
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Basic Power Terms
-
8/11/2019 Pv Training Manual
10/53
4.0 The Sun as a Resource
In order to design a photovoltaic system, we need to understand how much sun the area in which we are install-
ing the PV system will receive. For most regions of the world, the daily average of sun received is known. The
average amount of sun received is given in the units of PSH or Perfect Sun Hours.
A Perfect Sun Hour (PSH) represents a one hour period of a perfectly sunny day with no clouds. Therefore if a
region has a PSH of 4 it means that on average, the region will receive 4 hours of perfect sun per day. A PSH is
equivalent to having 1000 W/m2(watts per meter squared) of sun for one continuous hour.
PSH is found by adding up all the amount of sun received for every hour of the day and then dividing the total
by 1000 W/m2. Below in Fig. 5, the curve shows the amount of sun received per hour over the day and the box
shows the total number of perfect sun hours in the day. Table 1, on the following page, shows one example of
calculating PSH.
4.1 Perfect Sun Hours (PSH)
Figure 5. Diagram of Peak Sun Hours (PSH).
(www.homepower.com)
Understanding how the Earth receives light from the sun is extremely important in designing a photovoltaic
system. This section explains some of the basics of how the sun works and how we measure the strength of the
sun at different locations.
10
Peak Sun Hours
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - The Sun as a Resource
-
8/11/2019 Pv Training Manual
11/53
Hour Watts / m2 Watt Hours / m2
5AM - 6AM 0 0
6AM - 7AM 25 257AM - 8AM 25 25
8AM- 9AM 50 50
9AM - 10AM 300 300
10AM - 11AM 1000 1000
11AM - 12 PM 1200 1200
12PM - 1PM 1000 1000
1PM - 2PM 300 300
2PM - 3PM 50 50
4PM - 5PM 25 25
5PM - 6PM 25 25
6PM - 7PM 0 0
TOTAL Watt-hrs / m2 / Day 4000
Every hour of the day the sun will produce a different amount of power (watts) per meter squared. To nd out
how many perfect hours of sun are present in a day, the amount of watt hours / m2 is added up and then divided
by 1000 W / m2.
Watt hours / m2 / day = Hours of Perfect Sun per Day 1000 Watts / m2
Unfortunately, every day does give the same amount of sun. Therefore before we can know the PSH for a
certain area, we need to do the above calculation for every single day of the year and calculate the average. For
example, in the Amazon region of Ecuador the PSH is 3. Some days there have a PSH of 5 and other days havea PSH of 1, but on average the PSH is 3. Conveniently, we do not need to do the above calculations because
scientists have been collecting this information for many years and have created maps like the map on the fol-
lowing page in Fig. 6. Although world maps of PSH are generated for a given season and are too broad to use
for actual design, they provide a good illustration of what the PSH values are around the world.
4000 Watt hours / m2 / day = 4 PSH 1000 Watts / m2
Table 1
11
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - The Sun as a Resource
-
8/11/2019 Pv Training Manual
12/53
Fig
ure6.WorldMapofPSH.
ThisisamapoftheworldshowingthePSH
foreverypartoftheworld
(http://w
ww.sunwize.com/info_
center/insolmap.h
tm)
12
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - The Sun as a Resource
-
8/11/2019 Pv Training Manual
13/53
4.2 Orientation
Once we know the solar resource it is very important to mount the panel correctly so that we capture as much
sun as possible. Solar panels produce the most electricity when they are perpendicular to the sun. Since the sun
moves all day, it is not practical to keep moving the panel all day to keep it perpendicular to the sun.
In general, the best average position for mounting the panel is tilted towards the equator at an angle approxi-
mately equal to the latitude of the location. Hence, for locations on the equator, the optimum angle is horizon-
tal, but we still tilt that panel at an angle to allow the rain to help keep it clean.
The following are illustrations for an area about 30o north or south of the equator.
Figure 7. Different Ways to Orient Solar Panels.
(Solar Energy International - Photovol-
taics Design and Installation Manual)
moresunlight per square
foot falls on a perpendicular
surface (90oangle to the
suns rays is optimal
lesssunlight per square foot
falls on a horizontal surface
lesssunlight per square foot
falls on a vertical surface
13
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - The Sun as a Resource
-
8/11/2019 Pv Training Manual
14/53
5.0 How Solar Panels Function
A photovoltaic or solar panel converts the energy from the sun into electrical energy by using solar cells.
The Solar panel functions by collecting the energy from the sun, this energy comes in the form of a photon.
The photon is captured by the solar cell and the energy from the photon makes an electron move in the solarcell, which creates a current and electricity.
Figure 8. How a Solar Cell Functions
(www.nrel.gov)
14
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - How Solar Panels Function
-
8/11/2019 Pv Training Manual
15/53
5.1 IV Curves
Power = Current * Voltage
Figure 9. I-V curve.
(Solar Energy International - Photovoltaics Design and
Installation Manual)
15
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - How Solar Panels Function
-
8/11/2019 Pv Training Manual
16/53
5.2 Changes in IV Curves
(Solar Energy International - Photovoltaics Design and
Installation Manual)
(Solar Energy International - Photovoltaics Design and
Installation Manual)
Figure 10. I-V curve affected by temperature.
Figure 11. I-V curve affected by the sun.
16
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - How Solar Panels Function
-
8/11/2019 Pv Training Manual
17/53
6.0 The Charge ControllerThe charge controller is the brain of the PV system. The wiring from the solar panels, the batteries, and all of
the loads goes through the charge controller. The charge controller manages the ow of electricity from the
panels, into and out of the batteries, and to the loads. It has three main functions:
-Protects the battery from overcharging, by controlling how the PV panel charges the battery
-Protects the battery from discharge, by disconnecting the loads when the battery voltage gets too low
-Gives information on the state of change of the charge controller
Figure 12. Examples of Steca (left) and Morning Star (right) charge controllers.
17
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - The Charge Controlle
-
8/11/2019 Pv Training Manual
18/53
7.0 Wiring
The wiring is what carries the electricity from the panels through the charge controller to the batteries
and from the batteries through the charge controller out to the loads.
In a water system, if the pipes are too small, the water will not ow properly through the pipes to where
you need it. This is because of the resistance in the pipe.
Similarly, in an electric system, if the wiring is not sized and installed correctly, the electricity will not
ow properly to the loads. In electrical wiring, the two main considerations are the wire size, and the
terminations.
If the wiring is too small, or if the terminations are not made properly, either of these conditions will
result in too much resistance to the ow of electricity, and the system will not work properly.
7.1 Terminations
To make terminations properly, all wire connections need to be clean and tight. Twisting wires together
and taping them is not good enough. The looseness in these connections adds resistance to the ow of
electricity. The terminations need to be made with the proper connection materials.
7.3 Wire Sizing
When current passes through a wire, voltage is lost as a result of the resistance in the copper wire. This
is an important consideration in all systems, but more so in low voltage (12V e.g.) systems. Losing
2 volts on a 240V system is not too bad since it only represents less than 1% of the voltage lost to
resistance.
But, losing the same 2 volts on a 12V system represents a voltage loss of almost 17% which is quiteexcessive!
The amount of voltage that is lost for a given wire size and current ow is based on how much wire
there is, or the length of the wire.
We never want to lose more than 5% to voltage drop, so on a 12V system, we do not want to lose more
than 0.6V. Table 2, on the following page, is useful to determine the proper wire size.
18
Figure 13. Battery wire terminals.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Wiring
-
8/11/2019 Pv Training Manual
19/53
Table 2. Wire sizing chart.
19
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Wiring
-
8/11/2019 Pv Training Manual
20/53
As an example:
In Fig. 14, our panel is likely to produce 7 amps of current at 12V during good sun. The wire run from thepanel to the charge controller is 8 meters.
Using the wire sizing chart, if we use 1.5mm2copper wire, the volts lost for 100 meters of wire run and 7 ampsis 15 volts (listed as 15.02 on the chart). But we have 8 meters of wire, so 8/100 of this or 0.08. Therefore,for our example, the voltage lost is 0.08 * 15 = 1.2 V. This is twice as much voltage lost as we want to see,yet, we often see this size wire being used.
From the chart if we use 2.5 mm2wire, the volts lost is .08 * 9.46 or 0.8V. This is very close to what we would
like to see and would be ok, but we would not want to go a longer distance.
If we use 4mm2wire, then our voltage drop is 0.08 * 6 V, or .48V, which is less than the 0.6 volts maximumwe set. So, our best choice here is 4mm2wire.
Figure 14. Example determining wire size.
20
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Wiring
-
8/11/2019 Pv Training Manual
21/53
In a car when the tank gets low we go to the gas station and ll it up. A solar panel and battery work similarly.
During the day the solar panel lls up the battery with watt hours and at night we take the watt hours out of the
battery to power our lights and radio.
Figure 15. Comparison of a PV cell and Battery V. Gas and a Gas Tank
8.0 Batteries
A PV system is really a battery system with PV panels charging the batteries. Batteries store watt hours just like
a fuel tank stores fuel.
(www.shifting-gears.com/ shift-
ing_gears1.24.99.html)
(www.bpsolar.com)
21
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Batteries
-
8/11/2019 Pv Training Manual
22/53
8.1 Types of Batteries
There are many types of batteries, the types of batteries that we almost always use are called Lead Acid Batter-
ies. Below is a diagram showing the types of Lead Acid Batteries. Furthermore the types of Lead Acid Battery
we use is a ooded sealed lead acid battery.
Lead Acid Batteries
Flooded
Gel - more expensive
Sealed
Unsealed
(www.absak.com/catalog/
default.php/cPath/1_86_88)
Lead Acid Batteries are made for either car/trucks or solar panels systems. Batteries made for solar panel sys-
tems are called Deep Cycle Batteries.
Designed to release little amounts ofpower over long periods of time
Made to charge at a slow rate also
Solar Batteries - Deep Cycle BatteriesCar/Truck Batteries - Starter Batteries
When possible we want to use thistype
Designed to release a lot of power overa short amount of time
Can be charged at both slow and fast
rates
Figure 16. Types of Lead Acid Batteries.
22
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Batteries
-
8/11/2019 Pv Training Manual
23/53
8.2 Depth of Discharge
The term depth of discharge just means how far down we drain the battery each night.
The less energy we take out of the battery each night, the longer the battery will last.
A battery that is discharged 50% might last twice as long as a battery that is discharged 80% every night.
So, when we size the battery, we need to keep this in mind. If we determine that we need 100 watt hours of
storage in the battery for each night, then we would want to get a battery that stores twice this amount of watt
hours.
8.3 State of Charge of Batteries
How do we determine how full the battery is or what its state of chargeis? One way is to measure the voltage
using a digital multi meter (DMM). The voltage measurements must be made when
1. Battery is disconnected from the charge controller.
2. Battery has been at rest for 30 minutes.
Figure 17. Battery states of charge.
23
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Batteries
-
8/11/2019 Pv Training Manual
24/53
8.4 Battery Safety
Batteries can be extremely dangerous. There are three ways in which batteries can hurt someone: chemical, gas
and electrocution.
1.) Chemicals - The acid in the battery is bad for people and for the environment
If the acid from a batterygets on a persons skin it canburn the skin. If the aciddoes touch someones skinquickly apply baking soda tostop the burning
Throwing old batteries intothe woods causes a lot ofproblems to the environment.It can pollute the water killthe plants and animals. Al-ways bring your old batteryback to the place where you
purchase your new battery.
2.) Gas - Batteries vent a gas that be extremely ammable
3.) Electrocution- Batteries have a lot of electricity and can easily electrocute people
Wear goggles and gloves when working with batteriesto protect yourself from the chemicals.
Use wood boxes and shelves to store the batteriesmetal conducts electricity
Always tape the end of your tools and leave only theworking part of the tool exposed.
Never store batteries in an enclosed area allow the gasfrom the batteries to escape never have re or smoke acigarette near a battery.
24
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Batteries
-
8/11/2019 Pv Training Manual
25/53
9.0 Inverters
(WWF - Energy & Galapagos)
An Inverter is a piece of equipment that converts DC electricity into AC electricity, allowing the PV system to
be used for appliances that require AC current.
There are three types of Inverters: Square wave inverters, modied (quasi) - square wave inverters and sine
wave inverters. Each type of Inverter wave can power different types of electrical equipment.
If you need to power a computer or charge batteries for battery-operated tools, a sine wave inverter is required.
Figure 18. DC vs. AC.
Figure 19. Differenct Types of Inverter Waves
25
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Invertors
-
8/11/2019 Pv Training Manual
26/53
10.0 Designing a PV System
Fig.14 is a line drawing of a PV System with DC Loads. There are four key parts to the system: Solar
Panel, Battery, Charge Controller, and the Loads.
Figure 20. PV system with DC loads.
26
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Designing a PV Sytem
-
8/11/2019 Pv Training Manual
27/53
Loads Quantity Watts Hours/Day WattHours/Day
Fluorescent Lamp 2 20 4 160
LED Light 1 1 6 6
DC Outlet (computer or charger) 1 70 1 70
TOTAL 236
10.1 Calculating Total Daily Consumption in Watt-Hours
The rst step in designing a systems is to nd out the total consumption that needs to be powered by
the PV System. Once the total load on the system is known the PV System can be designed. The
rst line has been lled out as an example. Power consumption of common appliances are found in
Sec. 12.0.
Loads Quantity Watts Hours/Day WattHours/Day
TOTAL
27
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Designing a PV Sytem
-
8/11/2019 Pv Training Manual
28/53
10.2 Efciency of the PV System
Now that we know the loads that we need to provide power for, the next step is in sizing the main components
the solar panels, the battery, the charge controller, and the wiring.
We need to keep in mind, that we need the energy we calculated above available at the loads. But, whenever
energy is produced or moved, there are losses involved, since nothing is perfect. So, we need to size the panels
and the batteries large enough to account for the losses, and still have enough power left over for the loads.
28
Figure 21. PV system efciency.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Designing a PV Sytem
-
8/11/2019 Pv Training Manual
29/5329
Air Temperature C + 15 C = Temperature of the Solar Panel
Although Solar Panels need sun to produceenergy, when it is very hot out the solar panelswill not work as well as on sunny days when it iscold. Solar panels function the best at 25oC.Therefore, whenever the solar panel is warmerthan 25oC, it will not produce is rated watt-age.
For every degree that the solar panel temperature is above 25 C the solar panel output 0.5% less. Below is an
example.
If the Air Temperature = 30oC,
30oC + 15oC = 45oC
45oC = Temperature of Solar Panel
Temperature at which the solar panel produces its rated watts = 25oC
45oC-25oC=20oC (this is the amount that the solar panel is above the optimal temperature)
20oC * 0.5% per degree = 10% loss, so the panel output is 90% at 30oC
IN THIS EXAMPLE THE SOLAR PANEL LOSES 10% OF ITS POWER TO TEMPERATURE LOSSES.
PVPanel Output
In a perfect world, a 100 watt solar panel will produce 100 watts of power when the sun is shining on it. But,
this is rarely the case. A solar panel only produces its rated watts under a specic set of conditions:
Perfect sun shining on the panel, perpendicular to the surface
Temperature at 25 degrees Centigrade on the panel surface
Accounting for non-perfect sun:
We take care of the issue with the amount of perfect sun shining on the panel by using the PSH hours for the
hours of sun, instead of counting the hours when the sun is shining. Even though it might look like the sun is
shining brightly for 6 or even 8 hours in a day, we use the PSH value talked about earlier to estimate how many
watthours the panel will produce. For example, one might think that a 100 watt panel would produce 600 or
800 watt-hours in a given day because the sun is shining for 6 or 8 hours. However, if the PSH value for the
area is 3, then we can only count on the panel producing 3hrs * 100 watts, or 300 watthoursin a given day.
Accounting for non-standard Temperature:
As stated above, the panel produces its rated watts when the temperature of the panel surface is 25 degrees C.
So, we have to adjust for the times when the panel surface is NOTat 25 degrees C.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Designing a PV Sytem
-
8/11/2019 Pv Training Manual
30/53
To summarize, if we install a 100 watt solar panel in an area with a PSH of 3.0 and where the average air
temperature is 30 degrees C, we can expect to produce from this panel:
But, this output is still at the panel, and not at the load. We still have to get the energy through the wiring and
through the battery. We will lose some energy at each place.
Battery EfciencyMost batteries have an efciency rating of about 85%. This means when energy passes through the battery,
about 15% of the energy is lost.
Wiring Efciency
Earlier, we talked about the need to use larger wire so we dont have a large voltage drop. We wanted to keep
the voltage drop to 5% or less.
When we lose volts because of wire that is too small, this also means we lose energy because volts multipliedby amps = watts.
So, we need to include a loss factor for what we lose in the wire. If we size the wire correctly, this loss factor
could be as little as 3%. If we use too small, or too long a wire then this factor could be over 10% which is way
too large.
30
Battery Efciency is 85% or 0.85
Properly designed wiring may have a combined efciency of 97% or 0.97
100W Panel x 90% (because of loss due to temperature) x 3 PSH per day
= 270 watt-hrs per day of energy output.
Figure 22. PV panel output.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Designing a PV Sytem
-
8/11/2019 Pv Training Manual
31/53
10.3 Sizing the Panel
In taking all loses into account, the PV array size can be found by dividing the total number of watt hours re-
quired in a day by the multiplication of the PV panel output, battery efciency and wiring efciency. If we have
a condition where the air temperature is 30oC on average, we have a battery, and the wiring is sized correctly,
then the power delivered to the load from a 100 watt panel would be:
100W x 90% for temp. loss x 85% for battery losses x 97% for wiring losses = 74W
Next, multiplying 74W by the Peak Sun Hours (PSH), in one day in an area with a PSH of 3.0, the energy, inwatt-hours, available at the loads from a 100 watt panel would be:
74 watts * 3 hours of perfect sun = 223 watt-hrs
This is quite different than if we had assumed no losses and hoped to get 100 watts of power for 3 hours or
300 watt-hours. It is even more different than if we had hoped to get the 100 watts of power for all 6 hours
when the sun appears to be shining, or 600 watthours. So, it is very important to take all of these factors into
consideration when sizing the panel, or we will end up with a panel that will not properly charge the battery, and
our system will fail.
To size the panel, knowing the loads helps to combine these factors into a Panel Factor. For example, in thiscase, our panel factor would be 74% or 0.74 since we can expect to get 74% of the 100watt rated power of the
panel, or 74 watts. We often use a factor of 75% as a round number.
So, if for example, we had calculated the required loads to be 230 watt-hours per day, similar to the previous
example, then we would have to divide the 230 watthours by the panel factor to see how many watt-hours we
need to produce to overcome the losses.
230 watt-hrs / 0.75 = 307 watt-hrs
In an area with a Perfect Sun Hour (PSH) rating of 3.0, we would have three equivalent hours of sun to produce
these watthours, so we need a panel to be:
307 watt-hrs / 3 hours = 102 watts
We would purchase a solar panel rated at least 100 Watts. But for battery charging considerations, a larger panel
would be better to be able to ll up the battery more quickly following time with low sun.
This example was for a DC system, with no inverter. A charge controller is quite efcient in passing through
electricity, but the inverter does incur losses. If an inverter is in the system, we will have to add another loss
factor. Inverters are typically 85% to 90% efcient. So, with an inverter in the system, the panel and the battery
would need to be even larger.
31
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Designing a PV Sytem
-
8/11/2019 Pv Training Manual
32/5332
Figure 23. Sizing a PV system.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Designing a PV Sytem
-
8/11/2019 Pv Training Manual
33/53
10.4 Battery Sizing
The next step in the design process is to size the battery. We said before that the battery stores energy in wat-
thours, like a fuel tank stores fuel. And, we said that the battery has an efciency of 85%, meaning we lose 15%
of the energy in moving it through the battery. If we use our example of a load of 230 watthours, then we would
need a battery sized at:
230 watt-hrs / .85 for efciency = 271 watt-hrs
But, if we sized the battery at 271 watthours, this would mean that:
We would not have any energy left in the battery on days when the sun does not shine to charge the
battery back up.
We would also be completely discharging the battery every day, which we said earlier is very bad for the
battery.
So, we have to size the battery with these two considerations in mind:
Days with No Sunshine
We have to make some kind of guess as to how many days we want to keep the system working with no sun.
One day is obviously not enough. But, if we try to make it too long, the battery gets too big and expensive.
Often, we use three days as a good design range for providing for power with no sun.
So, to provide for three days of no sun, we would need the battery to store:
271 watt-hrs needed per day x 3 days with no sun = 813 watt-hrs
Prevent the Battery from Discharging More than 50%
The above sized battery would still have us completely discharging the battery during those times when there is
no sun for three days. We said earlier that we did not want to discharge the battery any further than half. So, we
would need to have a battery that would hold twice as many watthours as we need.
813 watt-hrs x 2 for depth of discharge = 1626 watt-hrs
So, we actually took our daily watt-hour requirement and multiplied it by 6. This was three times larger for the
days with no sun, and two times larger for the depth of discharge reasons.
271 Watt hours
271 Watt hours
271 Watt hours
271 Watt hours
271 Watt hours
271 Watt hours Keeping maximumdischarge at 50%.
For 3 days withoutsunshine.
33
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Designing a PV Sytem
{Total =1626 watt-hrs
-
8/11/2019 Pv Training Manual
34/53
Batteries however are not sold in Watt Hours, but are rather sold in Amp Hours therefore we have to do more
math to gure out how many Amp hours we need. Usually batteries are 12 Volts using the below formula we
can nd out amphours.
Using the equation for our example we get:
Changing the days without sun, and the allowable depth of discharge can make a big difference in the size of thebattery.
For example, if we said we only needed to provide for two days with no sun, and we could discharge the battery
to 55%, then the battery size would be:
230 watthours / 0.85 for battery loss = 271 watt-hrs
271 watthours x 2 days with no sun = 542 watt-hrs
542 watthours / .55 for depth of discharge = 985 watt-hrs985 watthours / 12V = 82 Amphours
So, we need to understand what we are providing for when we size, and purchase a battery. It might be
necessary for cost or portability, in this case to purchase the smaller battery. But, we need to know that we are
giving up the one day of energy without sun when we make that decision.
Watthours
= Amp Hours
Volts
1626 Watt Hours =136 Amp hours 12 Volts
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Designing a PV Sytem
-
8/11/2019 Pv Training Manual
35/53
11.0 System Installation
The best designed solar power system will not perform well if it is not properly installed. Care must be given to
the proper installation of all of the items included in the system.
11.1 Connecting Solar Panels in Parallel and SeriesThere are two ways to connect Solar Panels and batteries: series and parallel. When connecting in series the
voltage is added and the amperage stays the same. When connecting in parallel the voltage stays the same and
the amperage is added. The below examples are for solar panels, however batteries can be connected in the
same way.
24 Voltsat 3.5 Amps
35
12 Voltsat 7 Amps
Figure 24. Series connection.
Figure 25. Parallel connection.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - System Installation
-
8/11/2019 Pv Training Manual
36/53
24 Voltsat 7 Amps
36
Remember you cannot connect different types of panelsor batteries together in one series run or parallel run!
Figure 26. Series and parallel connection.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - System Installation
-
8/11/2019 Pv Training Manual
37/53
11.2 Installation of the Solar Panel
Aiming or Orientation
The earlier sections on design showed that to get the maximum output from the panel, it needs to be oriented to
the sun properly.
The panel should mounted on an angle approximately equal to the latitude of the area, and pointing to the
equator.
(If you are in the southern hemisphere, aim the panel to the north, and if you are in the northern hemisphere,
aim the panel to the south.)
So, for example, Mae Sot is at about 17degrees north of the equator, so the proper orientation for the panel
would be to tilt the panel at 15 to 20 degrees, aimed south, toward the equator.
If you are very close to the equator, then the latitude is close to 0 degrees. In these areas, the optimum angle for
maximum power might be at, but it is still good to tilt the panel 5 or 10 degrees to let the rain help to keep the
panel free of dust and dirt.
37
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - System Installation
-
8/11/2019 Pv Training Manual
38/53
Shading
If any portion of the panel is shaded at any time during the day, its power output will be signicantly reduced.
Quite often, panels are installed where there is no shading, but since trees and bushes grow quickly in some
areas, they become shaded, so this is a continuing maintenance item.
Sturdy
The panel must be installed on sturdy mountings so its orientation will stay as originally designed, and so it will
not be subject to being knocked.
Often times, it works to mount the panel on the roof. This should only be done if the roof is sturdy and is
aiming in the right direction. If this is not the case, it would be better to mount the panel on its own supports.
38
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - System Installation
-
8/11/2019 Pv Training Manual
39/53
Cabling from the Panel to the Controller
The cabling from the Panel to the Controller should be sized large enough, and kept as short as possible, and
located where it will not be a hazard or be pulled down.
At the panel location and at the building location, secure the cable tightly so that
-There is no tension being placed on the junction box of the panel
-There are no sharp edges where the cable enters the building.
39
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - System Installation
-
8/11/2019 Pv Training Manual
40/53
11.3 Controller Installation
The controller needs to be mounted in a location where there is not a lot of activity, to avoid the possibility of
being knocked into by carried items. It needs to be mounted securely to the wall, in a place where the cables
coming into it and going out of it can be secured independently to the building.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - System Installation
40
-
8/11/2019 Pv Training Manual
41/53
11.4 Installation of the Battery
The battery needs to be close to the controller to limit the length of the wire, and reduce the losses in this cable.
It should be in a non-metallic battery box (wood or plastic) vented to the air, and covered so nothing metal can
be placed on top of the battery.
11.5 Wiring Installation
Wiring should be neat, and fastened securely in all locations. This makes checking for trouble much easier, andavoids problems of things being hung on the wiring or cutting into the wiring.
The wiring needs to be large enough to avoid voltage drops.
Strain relief should be provided at all points where the wiring is terminated to avoid tension on the connection.
All terminations should be made with proper connection equipment (wire nuts or terminal strips). Try to avoid
just stripping, twisting, and taping for connections, as this leads to early failures.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - System Installation
41
-
8/11/2019 Pv Training Manual
42/53
11.6 Light Switch Installation
Give some thought to the location of the light switches.
First of all, try to install a separate light switch for every light. This way if only one light is needed, the others
can remain off.
It is good to install all of the light switches at the controller location, because this reduces the number of eld
terminations and connections, and points of potential failure. Then, all of the cables are direct runs from the
controller to the lights. If it is important to install a switch away from the controller and closer to the light, it is
best to make all of the terminations at the light or in the switch, and not just breaking into the wire run to cut in
a switch.
11.7 Load Connections
All wiring to loads must be connected through the charge controller. No wires should be terminated on thebattery except for the wires going to the charge controller. If loads are connected directly to the battery, then
these loads are not disconnected when the charge controller decides to turn the loads off to protect the battery,
and the battery will fail prematurely.
Switches
42
No!
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - System Installation
-
8/11/2019 Pv Training Manual
43/53
-
8/11/2019 Pv Training Manual
44/53
ITEM LOAD (Watts)Air Conditioner 1500
Blow Dryer 1000
Ceiling Fan 10 - 50Clock Radio 5
Clothes Washer 1450
Electric Clock 4
Iron 1500
Sewing Machine 100
Table Fan 10-25
Refrigerator/Freezer (19 Cu Ft.) 1000 Wh / day
Refrigerator/Freezer (16 Cu Ft.) 700 Wh / day
Refrigerator/Freezer (12 Cu Ft.) 470 Wh / day
Refrigerator/Freezer (10 Cu Ft.) 280 Wh / dayRefrigerator/Freezer (4 Cu Ft.) 210 Wh / day
Blender 350
Coffee Pot 1200
Microwavyy (.5 Cu. Ft.) 750
Electric Range 2100
Incandescent (100 W) 100
Incandescent (60 W) 60
Compact Fluorescent (60W equaivalent) 16
Incandescent (40 W) 40
Compact Fluorescent (40W equaivalent) 11
CB radio 10
CD player 35
Celular Telephone 24
Computer Printer 100
Computer (desktop) 80-150
Computer (laptop) 20-50
Stereo (average volume) 15
Stereo (Large full volume) 150
TV (12 inch black & white) 15TV (19-inch color) 60
VCR 40
Band Saw (14) 1100
Circular Saw (7.25) 900
Disc Sander 9 1200
Drill (1/4) 250
Drill (1/2) 750
Drill (1) 1000
44
Table 3. Common Loads.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Load Managemen
-
8/11/2019 Pv Training Manual
45/53
To have good load management you need to:
1.) Pay extreme attention to using only what youdesign for.
2.) If you have even 1 day with no sun - cut
back your use of the system that day.
3.) If possible - design the system to produce20% to 50% more than your design require-ment.
WHEN YOUR CHARGE CONTROLLER DISCONNECTS THE LOAD - THIS MEANS
THE BATTERY BANK HAS BEEN USED ALL THE WAY DOWN THROUGH ITS
THIRD DAY OF RESERVE AND WILL TAKE 3 DAYS OF GOOD SUN WITH NO LOADTO CHARGE BACK UP.
45
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Load Managemen
-
8/11/2019 Pv Training Manual
46/53
-
8/11/2019 Pv Training Manual
47/53
13.1 Wire Connections
Go around to all of the wire connections and check for tightness and that they are free of corrosion and dirt.
Often you will nd a loose wire connection and that will be the end of it.
If the wire terminations at the battery are becoming corroded and if the battery is dirty, take the connections
apart, clean the terminals and re-tighten them.
13.2 Battery
You will need to check the state of charge of the battery. This is done by disconnecting the battery from the
system and letting it sit for about a half hour and using a multi-meter to check the voltage.
Earlier in Sec. 8.3, we showed how the voltage reading relates to the state of charge of the battery:
If the battery is low, and you think there is no reason for it to be low such as there has been good sun for
several days, then the problem could be:
The battery is not getting properly charged. (which could be caused by a faulty solar panel or a faulty
charge controller)
The battery was discharged so deeply that its voltage is so low it cant be recharged by the solar system.This could have happened by by-passing the charge controller and connecting loads directly to the
battery.
To determine if the charge controller is charging the battery, in good sun:
With the battery still disconnected, measure the voltage where the wires from the solar panel come into the
charge controller. It should be an open circuit voltage between 17 and 20 volts.
Then connect the battery to the charge controller and see if a charging voltage is being sent to the battery. This
voltage might be around 14 volts.
47
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Trouble Shooting
-
8/11/2019 Pv Training Manual
48/5348
13.3 Solar Panel
If it does not appear that the solar panel is providing the output required to charge the battery, we can check its
open circuit voltage and short circuit current.
This should be done with the wiring from the solar panel completely disconnected from the charge controller.
Before checking the voltage and current, it is good to check inside the junction box (if it is accessible) to be surethat the diode has not been burned up. This can sometimes happen if a battery is connected in reverse polarity
and this reverse current passes through the charge controller and out to the panel. If the diode is burned up,
remove it. For a single panel installation, the diode is not necessary.
13.4 Check Load Terminals
If the voltage at the panel connection to the charge controller is correct, and if no voltage is being sent to the
battery, or to the loads then the controller might be bad.
However, some controllers have a minimum voltage level they need from the battery in order to even turn on. If
the voltage of the battery is so low that it is below this minimum voltage level, than the charge controller might
be ne, even though it will not turn on. In this case, you will need to change the battery out for a good one to
test the system.
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Trouble Shooting
-
8/11/2019 Pv Training Manual
49/53
14.0 About Us
Green Empowerment
Green Empowerment is a public non-prot international development organization based in Portland, Oregon
that is supported by individual donors, foundations, businesses, and international and governmental aid orga-
nizations. Our mission is to promote community-based renewable energy projects internationally to generate
social and environmental progress. Since our inception in 1997, we have developed a strong administrative
structure. We have a diverse funding base, important national & international partnerships, and a solid track
record.
Our Projects are usually associated with:
-Residential lighting and electricity
-Power for schools and clinics
-Energy for economic development and micro-enterprise
-Comprehensive community environmental plans and watershed protection
-The protection, development and accessibility of potable water sources
-Potable water pumping
We utilize small hydropower, biomass, wind and solar power projects to energize communities and stimulate
positive social and economic advances in an environmentally safe manner. All projects have a strong environ-
mental protection component that includes watershed mapping, resource conservation, and restoration activities.
We emphasize local leadership, community participation and long-term economic and environmental sustain-
ability. We partner with NGOs (non-governmental organizations) engaged in renewable energy projects. We
assist with feasibility studies, project planning, technical training and project fund raising, looking to the local
NGOs and communities to determine project priorities and goals.
Green Empowerment is committed to promoting renewable energy and sustainable development around the
world. We believe that access to electricity is fundamental to improving the quality of life and raising the stan-
dard of living for people everywhere. Our goal is to support community-based, renewable energy projects that
are economically and environmentally viable and that foster self-sufciency and true independence.
Contact Information:
Green Empowerment
140 SW Yamhill St. Portland, OR 97204, USA
(tel) 503-284-5774 (fax) 503-460-0450
www.greenempowerment.org
49
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - About Us
-
8/11/2019 Pv Training Manual
50/53
Palang Thai
Palang Thai is a Thailand-based non-prot organization dedicated to empowering grassroots communities and
small entrepreneurs to use renewable energy in ways that support sustainable development and participatory
democracy. Palang Thai has helped conduct hands-on trainings on renewable energy in Mykyina, Shan state in
Burma, and has helped TOPS and villagers to build two micro-hydro systems in Tak province, Thailand.
Contact Information:
Palang Thai
315/247 Sathupradit Soi 19, Bangkok, Thailand 10120
(tel) 662-674-2533 (fax) 662-6740-2533
www.palangthai.org
International Institute for Energy Conservation
IIEC is a non-governmental (NGO), not-for-prot organization with ofces in Africa, Asia, Latin America,
and North America. It was established in 1984, to foster the implementation of energy efciency in developing
countries and countries in transition. IIEC has full time local staff in each of its ofces that are well placed
to contribute to programs due to their extensive exposure to energy, transport and environment activities
in the region and their understanding of cultural issues relevant to the countries. As an organization with
proven technical capabilities, IIEC designs policies, implements programs, and supports institutions that
mainstream energy efciency in the entire value chain of energy systems and use. IIECs approach focuses on
implementation, resulting in policies developed in partnership with key policy makers and industry in our target
countries as well as the bilateral and multilateral institutions that help to shape energy policy and investmentpriorities globally.
Contact Information:
IIEC-Asia (Regional Ofce), Thailand
12th Floor, United Business Center II Bldg.,
Suite 1208, 591 Sukhumvit Rd. (Soi 33)
Wattana, Bangkok 10110 -- THAILAND
Tel: +66.2.662.3460-5
Fax: +66.2.261.8615
Email: [email protected]
50
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - About Us
-
8/11/2019 Pv Training Manual
51/53
Other Coordinators
Karen Health and Welfare Department
The Karen Health and Welfare Department (KHWD) (not part of the government) has, over the years, built upa network of medics and clinics operating inside Burma. They support over 36 clinics with a roster of approxi-mately 75 surgeons, medics, and nurses. The medics treat land mine victims and other casualties of the conict
and grinding oppression. More information: http://www.greenempowerment.org/burma.htm
Taipei Oversees Peace Service (TOPS), Thailand
TOPS in Thailand provides various humanitarian assistance, mainly educational programs, for refugees andlocal people affected by the inux of refugee populations and migrant workers who have ed from ghting orvarious type of persecution, mainly from Burma . TOPS recognizes that through full participation in decision-making, the participants in programs will become more condent in themselves, be able and willing to sharemore responsibilities of the programs and thereby become more self-reliant in dealing with the challenges inany aspects of their life. More information: http://thailand.tops.org.tw/ENG.HTM,Contact info: [email protected]
Zoa Refugee Care
ZOA REFUGEE CARE (ZOA) is an international NGO, operating in more than 10 countries worldwide.ZOA supports (former) refugees, internally displaced persons (IDPs), returnees and others who are affected byconict or natural disasters. More information: htpp://www.zoaweb.or, Contact info: [email protected]
Instructors
Walt Ratterman, Green Empowerments Field Director of Programs, has over 30 years of experience in
electrical construction. He is a NABCEP-certied solar system installer. He completed the Masters of Science
Program in Renewable Energy at Murdoch University in Australia (via the internet) in 2002, specialized
in renewable energy for the developing world. Walt currently serves as vice president of Knightsbridge
International- a non-prot, volunteer based, humanitarian aid organization. With Knightsbridge, Walt hasworked on projects in Thailand, Cambodia, Burma, Mongolia, Nicaragua, Philippines, Afghanistan, Ecuador,
and Nicaragua. Contact info: [email protected]
Chris Gracean has worked on technology and policy aspects of renewable energy in a variety of challenging
social and cultural contexts including Native American reservations, North Korea, Burma, and the post-restruc-
tured California energy industry. His Ph.D. research at the Energy and Resources Group (ERG, UC Berkeley)
focused on community-managed micro-hydroelectricity in Thailand, where he has lived since 2000. Besides an
MS and Ph.D. from ERG at U.C. Berkeley, he has a BA in Physics from Reed College. He has published over
40 articles on renewable electricity and energy policy. Contact info: [email protected]
Workbook Authors
Walt Ratterman
Seth Kassels
Dipti Vaghela
Sirikul Prasitpianchai (Thai translation)
51
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - About Us
-
8/11/2019 Pv Training Manual
52/5352
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Additional Notes
Notes:
-
8/11/2019 Pv Training Manual
53/53
Green Empowerment and Palang Thai Photovoltaic System, Training Manual - Additional Notes
Notes: