pumps

PumpsIntroduction

Take a look at our latest products on www.ecomcat.co.uk 747

Introduction to Vacuum PumpsVacuum pumps are designed to pump air or gases at pressures below atmospheric pressure. Working atbelow atmospheric pressure facilitates many tasks and research activities in laboratories. These rangefrom simple filtration to complex distillation and many others.

Due to their high flow, deep vacuum capability oil-sealed rotary vane pumps have traditionally been verypopular in laboratories as they are capable of handling most pumping requirements. However, due to thefact that vapour will condense in the pump, careful selection of traps, accessories and diligentmaintenance is required to ensure trouble-free use.

Not all tasks or experiments within the laboratory need high flow and deep vacuum and there arealternative pumping technologies that may be more suitable. Please talk to our Technical Office on01342 826836 if you require assistance.

Oil sealed rotary vane pumpsBest suited to applications that require high flow rates and pressures below 1 mbar. Traps and accessoriesare always required. Talk to our Technical Office if you require assistance.

Diaphragm pumpsThese are oil-free pumping mechanisms available in two forms, one for pumping air and one forpumping chemicals. A typical use of a chemical version would be for rotary evaporation.

Piston pumpsThese are oil-free pumping mechanisms that generally have a higher compression ratio than diaphragmpumps, and provide good flow characteristic when used in such applications as filtration, cell harvestingand vacuum oven drying. Not suitable where aggressive vapours or solvents are involved.

Scroll pumpsA sophisticated oil-free design that gives high flow rates and deep vacuum of the same order as rotaryvane pumps. Your application may require the use of a chemical trap.

Safety & HealthPlease consult your Safety Officer regarding the location of your pump and the management of exhaustfumes, especially if handling aggressive chemicals.

Pump selection - our rule of thumb guide for you. If you are in any doubt please contact our TechnicalOffice on 01342 826836 for assistance.

1. Select appropriate approximate vacuum for the application

2. Is chemical resistance required (yes or no)?

3. Select flow rate if appropriate. Approx flow rate should be 12 times the volume to be evacuated (litres per min) except for filtration, where there the system is not gas tight, use x4.Examples: a. Rotary evaporation of 5L flask plus condenser plus tubing (probable 12L in total),

therefore =12x2=24L/min pump flow rate:b. Vacuum oven of 50L capacity 50x2=100 L/min pump flow rate: c. Filtration of 4x1L flasks on manifold plus tubing (probable 5L in total), therefore

5x4=20L/min pump flow rate.

4. Do not ignore features for ease of handling i.e. catchpot, gauge etc

5. Add accessories to increase pump life

Application Approx vacuum required Notes Filtration 100~300 mbar Desiccation 100~300 mbar Aspiration 100~300 mbar Cell harvesting 100~300 mbar Rotary evaporators 10 mbar 80% solventsRotary evaporators 2 mbar 95%+ solventsGel dryers 50 mbar Too deep vacuum or too high flow rate cracks gelsCentrifugal evaporators 10 mbar 80% solventsCentrifugal evaporators 2 mbar 95%+ solventsFreeze dryers 0.1 mbar Vacuum manifolds 2 mbar Vacuum ovens 10 mbar Glove boxes 10 mbar Transfer chambers 10 mbar

Bigger is not better as too large a vacuum pump tends to increase the likelihood of condensable vapours bypassingthe cold trap and migrating into vacuum pump oil. For instance, a -55C system condenser will not condense outAcetonitrile vapour causing vapour to condense in oil.

Welch RietschleThomas RotaryVane Pump

Edwards Scroll Pump

KNF Mini Pumps

Vacuubrand Diaphragm Pump

Ilmvac Diaphragm Pump

Pumps

748 Take a look at our latest products on www.ecomcat.co.uk

521-003 Mityvac, Hand-operated Vacuum PumpsHand-held, durable vacuum pumps. Quick and easy to use, with only one hand required to operate andrelease vacuum. External vacuum release valve eliminates need to disengage pump from the line. Nozzlefits standard 6mm i.d. tubing. Both models have a pump rate of 16cm3/stroke and attain a vacuum of upto 409cm3 of mercury in a few seconds. Models have PVC body.

Cat. No. Description Price

521-003 Standard Mityvac vacuum pump with gauge POA

521-004 Standard Mityvac vacuum pump without gauge POA

Traditional Water Jet PumpMade from a modern non-flammable plastic material that has better corrosion resistance than stainlesssteel. It is resistant to a broad range of solvents, mineral and organic acids and alkalis, with very fewexceptions.


520-003 Traditional water jet pump POA

Azlon, Water Jet PumpA high performance, polypropylene water jet pump. The side arm tapers from 7 to 12mm.

Suitable for most laboratory water pressures Complete with integral non-return valve Will operate effectively (half vacuum) at a flow rate of 7 litres per minute Will produce maximum vacuum of 20-25mmHg at a flow rate of

17 litres per minute Available with or without pressure gauge (030mmHg)

Cat. No. Description Inlet tube O.D., mm Price

520-001 Water jet pump 16 POA

520-002 Water jet pump with vacuum gauge 16 POA

Boxer 3300P Compact Air and Gas PumpThe Boxer 3300P is the ideal laboratory pump for a wide range of applications. The high performance tosize ratio of this model offers a useful solution wherever suction or pressure applications are required.

The unit is based on the well established Boxer 3000 range of pumps. It has been specially designed asa flat package to compliment any laboratory shelf, and can be operated in any orientation.

The pump operates on 12V DC and being a low voltage pump, is safe to operate in most laboratoryenvironments. The unit is supplied with a switch mode power supply. This power supply can be used inany supply voltage from 110V to 240V. Air flow can be adjusted via the selectable voltage switch on theremote power supply.

The 3300P pump can be easily fitted with the filter and silencer which are offered as economical, semi-disposable accessories.

Contamination- and metal-free path Wetted parts manufactured in polypropylene and nitrile Maintenance free Safe, low voltage supply (12V DC) Quiet operation Flow control via selectable supply voltage

SpecificationMaximum flow rate, m3/hr (L/min) 1.2 (20)Maximum vacuum, mbar 400Maximum pressure, mbar 650Dimensions (hxwxd), mm 61x155x222Weight (including power supply), kg 1.7Electrics 230V AC to 110V AC


521-019 Boxer 3300P Compact air and gas pump supplied with POApower adaptor and a range of plugs

521-020 Air filter and silencer POA

520-003

520-002 520-001

520-002

521-019 shown with 521-020New

PumpsCharles Austen


Capex 8C Diaphragm Vacuum Pump/CompressorThe Capex 8C is ideal for continuous duty as either a vacuum pump or compressor. It has a compact yetrugged aluminium case with a flush-folding carry handle and built in cable tidy. It incorporates unique T-slot rails for quick and easy mounting of retrofittable accessories such as collection flasks and vapour traps.

Portable with flush-folding carry handle Suitable for applications such as vacuum and pressure assisted filtration and sampling

SpecificationFlow rate, m3/h (L/min) 0.48 (8.0)Maximum vacuum, mbar 240Maximum pressure, bar 2.0Dimensions (hxwxl), mm 214x137x282*Weight, kg 3.75


521-061 Capex 8C diaphragm vacuum pump/compressor POA

* includes the cable tidy and connectors

Dymax 5, Diaphragm Vacuum Pump/CompressorDesigned and manufactured with the laboratory user in mind, the Dymax 5 incorporates low noise levels,splash proof switch and plug-in mains lead. It is ideal for supplying air in microbiology experiments andfor sampling a wide range of gases.

Vacuum Tweezer Option Supplied with a hand piece and set of suction probes, this accessory is ideal for handling a small delicateobject as fine as gold leaf. The integral, washable filter also makes it useful for precision cleaning.

SpecificationMaximum free flow rate, m3/h (L/min) 0.3 (5.0) Dimensions (hxwxl), mm 125x151x210Maximum vacuum, mbar 500 Weight, kg 2.1Maximum pressure, bar 0.8 Standards IEC 1010Speed, rpm 2800


521-063 Dymax 5 cased pump POA

521-064 Dymax 5 cased pump with vacuum tweezer kit POA

Innovac, Chemically Resistant Diaphragm Vacuum PumpsThis range of dry vacuum pumps offer class leading performance with chemical resistance to virtuallyall corrosive gases and solvent vapours. Housed in a tough alloy case featuring unique T-slot rails forquick easy mounting of all necessary attachments such as vacuum gauges, vapour traps or condensers.The flush-folding carry handle provides stowage for the pumps service tool and conceals a handy hourmeter, which can monitor process times.

SpecificationModel Innovac 20 Innovac 40Maximum free flow rate, m3/h (L/min) 1.2 (20) 2.3 (38)Maximum vacuum, mbar 8.0 8.0Maximum pressure, bar 1.0 1.0Speed, rpm 1400 1400Dimensions (hxwxl), mm 214x136x331 214x136x393Weight, kg 8.5 11.6Standards IEC 1010 IEC 1010


521-102 Innovac 20 chemically resistant vacuum pump POA

521-103 Innovac 40 chemically resistant vacuum pump POA

Contamination-free vacuum Advanced reliability with exceptionally long

running life Fully corrosion resistant with all wetted parts

constructed entirely from PTFE and Kemrez

Applications include benchtop use for filtration, rotary evaporation, gel drying and vacuum distillation

Vacuum down to 8mbar

Contamination-free pumping of air and gas Ideal for continuous duty month after month Easy to maintain

Up to 5.0L/min flow Vacuum down to 500mbar Quiet operation

521-061

521-103 521-102

New

521-063 New

521-064 New

Fluid Aspiration

Pumps


Ilmvac, BIOVAC 102, Fluid Aspiration SystemThe new BIOVAC 102 is a portable vacuum aspiration system with integrated, chemically resistant,diaphragm pump that is ideally suited for the safe aspiration of biological supernatants as well asremnants of chemical or medical experiments. All elements of the liquid pathway are chemically inert,allowing a wide range of reagents to be used and for sterilisation by Virkon.

It is easy to remove small amounts of excess liquids from object slides, petri dishes, well plates etc,through various kinds of pipettes which are inserted into the pipette carrier of the hand piece. The largeintegrated catch pot is isolated automatically, as soon as the maximum filling level is reached.

Between the catch pot and the pump, there is a filter holder in which diaphragm filters of up to 0.22 m can be inserted allowing bacteria and viruses to be handled safely. The catch pot and thediaphragm pump are connected via fast locking couplings with integral bi-directional isolation valve.The chemically resistant diaphragm pump employed in the BIOVAC has a long life (10,000 runninghours) and can be operated by means of a foot switch.

2-litre autoclavable glass catch-pot Automatically isolates when full Lid with integrated fine filter casing with quick release bayonet joint Bacteriological filter pore size of 0.22 m Hose connection via quick fit coupling with bi-directional shut-off valve Hand piece with multi option pipette carrier Chemically resistant diaphragm pump operated via a foot switch 2 year warranty and very low servicing costs

BIOVAC 102 - Stand alone fluid aspiration system, ready for use, comprising: Diaphragm pump, glasscatch-pot, hand set, foot switch and carry handle.

Specification Flow rate, m3/hr (L/min ) 12Ultimate pressure, mbar

PumpsFluid Aspiration


Vacuubrand, BioChem-VacuuCenter, Fluid Aspiration SystemsSimple, safe and easy to use vacuum aspiration system, specifically designed for fluid aspiration frombulk samples to microplates in chemistry, biochemistry, biology and medicine.Automatically controlled, low maintenance, high performance vacuum pump with condensate catchpoton exhaust provides vacuum automatically on demand for single and multiple workstations, with noneed for foot pedal or start / stop switch. This ready-to-use unit comes complete with an ambidextrous,ergonomically designed hand control, which accepts all common pipettes and tips, and a large 4 litreautoclavable collection bottle (with additional port for second hand control) and biohazard filter. It isalso available without pump (BVC01) for connection to existing vacuum systems.

BVC21 - Stand alone fluid aspiration system, ready for use unit comprising vacuum pump, vacuumcontrol, collection bottle/filter, hand set.

BVC01 - Fluid aspiration system without pump for connection to existing vacuum system

High performance vacuum pump (BVC21 only) For up to two workstations Appropriate chemical resistance Large capacity reservoir Easy to use

Specifications Model BVC21 BVC01Dimensions (lxwxh), mm 520x300x500 300x250x500Weight, kg 11.0 4.0Electrical supply 230V, 50/60Hz 230V, 50/60Hz


521-179 BVC21 Stand alone fluid aspiration system POA

521-180 BVC01 Fluid aspiration system without pump POA

Accessories


521-181 Additional hand control with hose POA

521-183 Additional container, 4L autoclavable POA

521-182 Quick coupling for flexible hose connecting hand control and container POA

521-186 Spare hose for hand control, 2m POA

521-184 Spare protection filter with mounting tube POA

521-185 Elbow hose connection for hand control and container POA

Welch Rietschle Thomas, Fluid Aspiration SystemThis dry vacuum aspiration system is specifically designed for fluid aspiration from bulk samples tomicroplates in biochemistry, biology, chemistry and medicine. This ready to run unit is supplied completewith autoclavable collection vessel, footswitch, pipette holder, 1.8m tubing, vacuum regulator and gauge.

SpecificationFlow rate, m3/hr (L/min) 34 (2)Maxiumum vacuum, mbar 560Capacity plastic autoclavable bottle, ml 1200Tubing required, I.D., mm 6.35Dimensions (wxdxh), mm 375x210x255Weight, kg 4.9


691-057 Model 2515 Fluid aspiration system POA

Please note: 100 and 115V versions are available. Please contact our Technical Office on 01342 826836.

For replacement silicone pipette holder and tubing, please contact our Technical Office on 01342 826836.

Cost effective Quiet operation Accepts common pipette tips

521-179

521-180

691-057

Fluid Aspiration

Pumps


521-400 UNIJET Aspirator PumpsUseful for centrifugal concentrators, gel dryers, vacuum ovens, filtration etc. A UNIJET aspirator pump ismore sturdy and needs much less maintenance than an oil-lubricated vacuum pump. Harmful aerosolslike acids, alcohol etc. are absorbed in the bath water, which can be buffered if necessary.

All UNIJET models feature:

An energy saving and environmentally safe vacuum system A strong vacuum created by pumping water through two or four Teflon Venturi jets Teflon jets offer excellent chemical resistance Extremely quiet operation No oil needed Analogue vacuum gauge Easy to clean and drain

UNIJET I Non Refrigerated Aspirator Pumps The UNIJET I aspirator pumps have a bath volume of 8 litres and are available with vacuum pressurecontrol and 4 jet pumps, or without vacuum pressure control and 2 jet pumps.

SpecificationsModel UNIJET I, 2 jets UNIJET I, 4 jets

without vacuum pressure control with vacuum pressure controlBath material clear plastic plasticAir flow, L/min 28 35Bath volume, litres 8 8Dimensions (wxdxh), mm 250x370x400 250x370x400Weight, kg 8.5 8.5Power consumption, W 160 160


521-400 UNIJET I aspiration pump with 2 jets without vacuum pressure control. POASupplied with non refrigerated water bath, analogue vacuum gauge.

521-401 UNIJET I aspiration pump with 4 jets with vacuum pressure control. POASupplied with non refrigerated water bath, analogue vacuum gauge.

UNIJET II and UNIJET IV Refrigerated Aspirator Pumps The UNIJET II and IV pumps are designed for absorbing larger quantities of solvents, especially incombination with rotary evaporators. They have a built-in cooling system to chill the water bath and toeliminate normal heat-up caused by pump operation. Cold water has a high capacity to absorb aerosolswhich are released by the samples. The vacuum that is generated depends on the temperature of the water:The lower the temperature, the higher the vacuum; at +4C a vacuum pressure of ca. 4mbar is attainable.

The UNIJET II and IV aspirator pumps have a bath volume of 10 litres and are available with vacuumpressure control and 4 jet pumps (UNIJET IV) or without vacuum pressure control and 2 jet pumps (UNIJETII). Both models feature Fuzzy Logic functionality.

SpecificationsModel UNIJET II, 2 jets without vacuum UNIJET IV, 4 jets with vacuum

pressure control pressure controlBath material stainless steel stainless steelAir flow, L/min 35 95Residual pressure @4C, mbar 4 4Bath volume, litres 10 10Dimensions (wxdxh), mm 326x438x638 326x438x638Weight, kg 38 38Power consumption, W 500 500


521-402 UNIJET II aspiration pump with 2 jets without vacuum pressure control. POASupplied with 10 litre refrigerated water bath, digital display for temperature, vacuum gauge and dual vacuum pipe.

521-403 UNIJET IV aspiration pump with 4 jets with vacuum pressure control. POASupplied with 10 litre refrigerated water bath, digital display for temperature, vacuum gauge and dual vacuum pipe.

New

521-403New

PumpsWelch Rietschle Thomas


691-056

691-041GelMaster Gel Dryer Vacuum SystemThe Welch Rietschle Thomas GelMaster is a patented vacuum system with roomtemperature vapour trap and vacuum system integrated into a single, high-efficiency,low-maintenance unit.

The vapour trap reduces the overall vapour load enabling a compact, high-efficiencydiaphragm pump to be the primary vacuum force.

Trapped fluids accumulate in the collector over 10 to 15 gel drying runs (and it is justas efficient on the last run as on the first). When the fluid reaches the red zone in thefluid-level sight glass, simply open a valve and drain the collected fluid. The system isthen ready to dry more gels. The trapping fluid can then be re-used over and overagain, since it does not mix with the condensate.

The diaphragm pump delivers a powerful, non-fluctuating vacuum for fast,smooth drying.

Complete system for gel dryers Controlled evaporation rate to ensure crack-free gels Fast and quiet operation

SpecificationsCondensed vapour capacity, litres 1.5Inlet port 10mm ID hose nippleDimensions (wxdxh), mm 286x394x365Weight, kg 15.2


691-041 GelMaster gel dryer vacuum system, supplied complete POAand ready-to-use with 1.7m of PVC vacuum tubing, in-line stopcock, hose clamps, detachable power cord and 1 litre of trapping medium

Please note: 100 and 115V versions are available. Please contact our Technical Office on01342 826836.

High Performance, Dry Vacuum General Utility PumpsWelch Rietschle Thomas dry piston pumps are ideal replacements for oil sealed pumpsfor general utility applications such as drying and degassing. These compact pumpsare built for extended service life and are supplied with accessories for ease of use.Carrying handle, suction-cup feet, power cord, on/ off switch, regulator, gauge andtrap are included. Suitable for use with:

Vacuum ovens Transfer lines Glove box transfer chambers

SpecificationsModel 2561 2581Flow rate, m3/hr (L/min) 3.0 (50) 4.9 (83)Ultimate vacuum, mbar 4 4Maximum pressure, mbar 6.7 6.7Motor, HP 13 13Tubing required, I.D., mm 10 10Dimensions (lxwxh), mm 439x165x267 432x191x305Weight, kg 9.7 13.4

Cat. No. 691-055 691-056

Price POA POA

Please note: 100 and 115V versions are available. Please contact our Technical Office on 01342826836.

Welch Rietschle Thomas

Pumps


691-048 Automated Self-Cleaning, Dry Vacuum System for RotaryEvaporation, Concentration, Distillation and Similar ApplicationsThis self-cleaning dry vacuum system gives an oil-free vacuum using a two-stage diaphragm pump. WithPTFE used on all wetted surfaces, including the diaphragm, the pump is built to resist aggressive chemicalvapours and has an extended service life.

Oil-free system for rotary evaporators Vacuum regulator Resistant to corrosion with PTFE construction Self-cleaning purge extends pump life but does not interfere with vacuum Patented valve design ensures fast, effective pumping Vent switch to minimise vapour condensation in pump

The glass inlet separator helps protect the pump from ingesting liquids or particles. The gas ballast orvent switch acts to minimise vapour condensation when pumping heavy vapour loads. Vacuumregulation is accomplished with an adjustable bleed valve.

Any particles, water or condensed vapour that may have been ingested into the pump are purged whenit is shut off. The self-cleaning purge automatically turns on for 2 minutes after turning off the pump. Anexhaust separator catches any liquid or particles during the purge cycle.

SpecificationsModel 2023 2027Vacuum, mbar 10 2Flow rate, m3/hr (L/min) 1.62 (27) 1.62 (27)Gauge dial digitalMotor, HP 15 15Tubing required I.D., mm 7 7Dimensions (lxwxh), mm 324x203x292 324x203x292Weight, kg 12.7 12.7


691-048 Model 2023 automated dry vacuum system supplied with power cable and POAoperating manual with applications advice

691-049 Model 2027 automated dry vacuum system supplied with power cable and POAoperating manual with applications advice

Self-Draining Teflon Pumps for Rotary Evaporation,Concentration and DistillationThese two stage oil-free, fully corrosion resistant pumps are suitable for demanding applicationsincluding working with TFA, HCI, formic and acetic acid. A patented high flow valve system allows thesepumps to supply fast, repeatable vacuum.

SpecificationsModel 2021 2031Ultimate vacuum, mbar 2.7 2.7Flow rate, m3/h (L/min) 1.1 (18) 1.6 (27)Motor, HP 15 15Tubing required, I.D., mm 7 7Dimensions (lxwxd), mm 254x254x175 254x254x175Weight, kg 9.1 9.1


691-050 Model 2021 self-draining teflon pump supplied with power cable and silencer POA

691-051 Model 2031 self-draining teflon pump supplied with power cable and silencer POA


Oil-free High flow valve technology

Fast, repeatable vacuum Quiet operation

New

691-049New

691-051New

PumpsWelch Rietschle Thomas


691-042Dry, Dual-Function Vacuum and Pressure Pump for Filtration and AspirationWelch Rietschle Thomas dry-piston vacuum pumps are ideal for air sampling, pressure/ vacuum filtration,water aeration, flame photometers etc. The units are built for continuous-duty operation with low noiseand a service life that exceeds diaphragm pumps.

Regulators and gauges make it easy to meet your vacuum and pressure requirements. Discharge air isfiltered and noise is muffled with a filter. A moisture trap keeps water from being accidentally drawninto the unit.

All wetted aluminium parts are treated for corrosion protection from moisture. All other wetted parts arestainless steel. The motor is thermally protected. Carrying handle, suction-cup feet, power cord, on/off switch, regulator, gauges and traps are included.

NB; These pumps are not recommended for pumping acid, base or organic vapours.

SpecificationsModel 2522 2534 2546Flow rate, m3/hr (L/min) 1.1 (18) 1.7 (28) 2.3 (38)Maximum continuous pressure, bar 2 2 2Maximum vacuum, mbar 133 90 80Typical filter funnel capacity 1-2 1-4 1-6Motor, HP 18 18 18Tubing required, ID., mm 7 7 7Dimensions (lxwxh), mm 205x224x254 205x224x254 205x224x254Weight, kg 5.3 5.3 5.3


691-042 Model 2522 dry dual-function vacuum and pressure pump POA




Dry Vacuum System for Cell HarvestingThe Dry Vacuum System provides high throughput flow which allows up to 256 sample systems to behandled. With high flow at low pressure the system will handle even particularly sticky or viscoussubstances. Carrying handle, suction-cup feet, power cord, on/ off switch, regulator, gauge and trap areincluded.

SpecificationsModel 2585 2567Well system 256 96Flow rate, m3/hr (L/min) 10.2 (168) 4.9 (83)Ultimate vacuum, mbar 80 80Maximum pressure, bar 1 1Motor, HP 13 13Tubing required, I.D., mm 10 10Dimensions (lxwxh), mm 282x234x279 150x254x254Weight, kg 11.6 7.5


691-039 Model 2585 Dry Vacuum System POA

691-054 Model 2567 Dry Vacuum System POA


Aspiration of buffer solutions during cell harvesting is permitted, but do not allow liquids to be ingested into thepump. Not recommended for pumping acid, base, organic vapours or gases.

Oil-free pumping technology is virtuallymaintenance-free

Compact size takes up little bench space Quiet operation

Attached inlet trap to prevent accidentalingestion of liquid

Vacuum gauge allows verification of vacuum level

Pressure regulator Vacuum regulator Oil-free system delivers clean air Corrosion protection from moisture

Continuous-duty operation Quiet operation Compact

New

691-054 New

Welch Rietschle Thomas

Pumps


691-035

691-047

691-036

691-037

W-Series Rotary Vane Vacuum PumpsThe W-Series pumps from Welch Rietschle Thomas are oil-lubricated, rotary vane high-vacuum pumpssuitable for use with freeze dryers, centrifugal concentrators and vacuum ovens.

Model 8917-80 is supplied with a built-in large capacity acid neutralisation filter which will lead to anextended service interval. The acid neutralisation filter is designed for use with TFA, TFA by-productsand acetonitrile.

Cool running - special interstage fan delivers improved seal life, reliability and lengthens the timebetween oil changes

Cool surface temperature - maximum 20C rise above ambient Easy oil-change valve - with a simple turn, spent oil is neatly directed into a beaker for inspection

or a bottle for recycling. A tube can be attached for remote collection. Unibarb hose connections to eliminate need for expensive clamps and flanges Quiet operation Compact Extended service interval for model 8917-80

SpecificationsModel 8907 8912 8917 8917-80Ultimate vacuum gas 1.3x10-4 1.3x10-4 1.3x10-4 1.3x10-4

ballast closed, mbarUltimate vacuum gas 80 60 40 40ballast (fully open), mbarFlow rate, m3/hr (L/min) 3.4 (56) 5.2 (86) 8.4 (138) 8.4 (138)Nominal pumping 3.2 (53) 4.8 (80) 7.6 (125) 7.6 (125)speed, m3/hr (L/min)Motor, HP 13 13 13 13Pump speed, rpm 1425 1425 1425 1425Inlet connection Unibarb Unibarb Unibarb UnibarbTubing required, I.D., mm 11, 20 11, 20 11, 20 11, 20Oil capacity, litres 1.15 1.08 1.38 2.5Noise level , dB(A)

PumpsEdwards


520-022

520-022 DETAIL

691-021

691-020

RV Series Rotary Vacuum PumpsThe RV series pumps are unique in their capability to deliver high or low throughputs with high ultimatevacuum, which combined with ultra-low noise levels makes them ideal for a wide range of applicationsand environments. They also feature a fast acting inlet valve to seal the pump for suck-back protection.The pumps are easy to install, use and maintain. All the controls are clearly marked and have large fingergrips for ease of use. Inlet and outlet are both fitted with standard NW25 flanges. Supplied with 1 litreof Ultragrade 19 oil. Power cord is required but not included with the pumps. For Health and Safetyrequirements an oil mist filter is required (see below).

SpecificationsModel RV3 RV5 RV8Pumping speed, m3/h (L/min) 3.3 (55) 5.1 (85) 8.5 (140)Displacement, m3h1 3.7 5.8 9.7Ultimate vacuum, mbar 2x103 2x103 2x103

Noise, dB(A) 48 48 48Max. water vapourpumping rate gh1 220 220 220Oil capacity, L 0.7 0.7 0.75 Dimensions (wxdxh), mm 158x430x224 158x430x225 158x470x261Weight, kg 21.6 21.5 26.0

Cat. No. 520-022 520-023 520-024

Price POA POA POA

Accessories


520-028 Power cord, IEC socket, 2m long with 3 pin plug POA

520-014 Ultragrade 19 mineral oil, 4L POA

Speedivac 2 Vacuum PumpGeneral purpose single stage laboratory pump. For 220240V, 50Hz single phase supply. Supplied withUltragrade 19 oil, non-return valve and inlet/outlet nozzles. For Health and Safety requirements an oilmist filter is required.

SpecificationsPumping speed, m3/h (L/min) 2.3 (38)Displacement, m3/h (L/min) 2.7 (45)Ultimate vacuum, mbar

Without gas ballast 1.3x101

With gas ballast 6Vacuum inlet, mm 11 or 15 nozzleOutlet, mm 12Oil capacity, L 0.5 Weight, kg 12.5


691-021 Speedivac 2, vacuum pump POA

520-014 Ultragrade 19 mineral oil, 4L POA

EMF Series Oil Mist Filters Protection from oil mist emissions as required by COSHH and Health and Safety regulations

(EMF filters have 99.999% efficiency) Suitable for rotary pumps up to (330L/min) Unique odour element to neutralise oily smells The white bottom half of the body is translucent, allowing the oil level to be monitored For safety, if the oil element becomes blocked, an integral pressure relief valve will open


691-020 EMF10, oil mist filter complete with KF25 connections 34in. BSP to KF25 adaptor, POAcentring ring with O ring and clamp. Fits RV3, 5 and 8

691-019 EMF3, oil mist filter supplied complete as above but fits Speedivac 2 POA

Edwards

Pumps


XDS and XDS-C Dry Vacuum Scroll PumpsCompletely dry, lubricant-free vacuum pumps with vapour handling. The innovative XDS and XDS-C drypumps were designed by BOC Edwards to provide vacuum totally free of lubricants. Bearings are isolatedfrom the vacuum environment by a patented bearing shield. Uniquely, by using a scroll mechanism thereare no bearings, bearing purges, grease or oil under vacuum. Controllable gas ballast is standard andmakes the XDS and XDS-C suitable for pumping condensed vapours.

These pumps are portable, air-cooled and cost effective. Power consumption is very low and, typically,no other utilities are required. Low vibration and noise levels make them ideal for laboratory use. TheXDS pumps are not supplied with a power cord.

A carefully selected and tested combination of chemically resistant materials makes the XDS-C series idealfor a wide range of laboratory wet chemistry applications.

Typical applications for XDS-C pumps: gel drying, rotary evaporation, centrifugal concentration andother applications where condensable vapour are pumped.

Typical applications for XDS pumps: scanning electron microscopes, ion implanters (beamline and endstations), sputtering, turbomolecular pump backing and general clean pumping applications.

Totally dry, lubricant-free vacuum 3-position gas ballast selector - Pumps in excess of 200 gh1 water vapour Ease of maintenance - No oil to buy, change or dispose of, no re-greasing of bearings, no special

tool kits or jigs for service, simple supply voltage selection Dual voltage/frequency

SpecificationsModel XDS5 XDS10 XDS5-C XDS10-CDisplacement50Hz, m3/h (L/min) 5.7 (94) 11.3 (186) 5.7 (94) 11.3 (186)60Hz, m3/h (L/min) 6.7 (111) 13.4 (221) 6.7 (111) 13.4 (221)

Peak pumping speed50Hz, m3/h (L/min) 4.8 (94) 9.3 (153) 4.8 (79) 9.3 (153)60Hz, m3/h (L/min) 6.0 (99) 11.1 (183) 6.0 (99) 11.1 (183)

Ultimate vacuum 0.07 0.07 0.9 0.9(total pressure), mbarWater vapour handling, gh-1

gas ballast low/ high flow 70/>200 70/>200 70/>200 70/>200Motor supply voltage50Hz/ 60Hz 1 phase 110 or 220240V/115120 or 230240V (all models)50Hz/ 60Hz 3 phase 200220 or 380415V/200230 or 460V (all models)

Power, kW 0.3 0.3 0.3 0.3Operating temperature, C (F) 10 to 40 (50 to 104), (all models)Noise level, dB(A) 55 55 55 55Vibration, mms-1 (rms) 200Exhaust and inlet connection 25NW 25NW 25NW 25NWDimensions (lxwxh), mm 427x249x288 (all models)Weight, kg 23 24.5 23 24.5

1 phase vacuum pumps 520-034 520-036 520-038 520-040

Price POA POA POA POA

3 phase vacuum pumps 520-035 520-037 520-039 520-041


Accessories


520-028 Power cord, IEC socket, 2m long with 3 pin plug POA

520-025 Aluminium rifled nozzle POA

520-042 Centring ring with O ring POA

520-043 Hinged clamp POA

A new model, the XDS35i is also available, this has a peak pumping speed of 35m3/h. Please contact our TechnicalOffice on 01342 826836 for details.

520-036

520-040

KNF

Pumps


521-057

521-201

521-206

521-204

521-093

521-029 to 521-031

Mini Vacuum Pumps/CompressorsIdeal for general use around the laboratory/educational establishments.

SpecificationsModel N86 KN.18 N86 KT.18 N811 KN.18 N811 KT.18Flow rate, m3/h (L/min) 0.36 (6) 0.33 (5.5) 0.69 (11.5) 0.69 (11.5)Vacuum, mbar 100 160 240 290Pressure, bar 2.4 2.5 2 2Diaphragm EPDM PTFE coated EPDM PTFE coatedDimensions (wxdxh), mm 90x164x141 90x164x141 90x187x157 90x187x157Weight, kg 1.9 1.9 2.5 2.5

Cat. No. 521-057 521-200 521-201 521-202


SpecificationsModel N816.3 KN.18 N816.3 KT.18 N816.1.2 KN.18 N816.1.2 KT.18Flow rate, m3/h (L/min) 0.96 (16) 0.96 (16) 1.8 (30) 1.8 (30)Vacuum, mbar 15 20 100 160Pressure, bar 0.5 0.5 0.5 0.5Diaphragm EPDM PTFE coated EPDM PTFE coatedDimensions (wxdxh), mm 90x361x141 90x361x141 90x361x141 90x361x141Weight, kg 3.95 3.95 3.95 3.95

Cat. No. 521-203 521-204 521-205 521-206


Laboport Vacuum PumpsPTFE, corrosion resistant, diaphragm, oil-free The Laboport series provides a powerful alternative to water jet pumps, operating without water. Theytherefore save water and reduce environmental pollution. They also reduce operating costs dramatically.The pumps provide a constant vacuum, independent of water pressure and temperature. With theexception of N840.1.2FT.18 and N842.3FT.18, these pumps are single-head designs.

SpecificationsModel N810 FT.18 N820 FT.18 N840 FT.18 N810.3 FT.18Flow rate, m3/h (L/min) 0.6 (10) 1.2 (20) 2 (34) 0.6 (10)Vacuum, mbar abs 100 100 100 8Pressure, bar 1.0 1.0 1.0 1.0Dimensions (wxdxh), mm 256x146x187 268x159x207 297x171x226 281x140x187Weight, kg 5.9 7.1 10.3 6.9

Cat. No. 521-053 521-054 521-055 521-029


SpecificationsModel N820.3 FT.18 N840.3 FT.18 N842.3 FT.18 N840.1.2 FT.18Flow rate, m3/h (L/min) 1.2 (20) 2 (34) 2 (34) 3.6 (60)Vacuum, mbar abs 8 8 2 90Pressure, bar 1.0 1.0 1.0 1.0Dimensions (wxdxh), mm 312x154x207 341x166x226 341x167x223 341x160x226Weight, kg 9.3 12.6 13.4 12.6

Cat. No. 521-030 521-031 521-093 521-091


Simple to operate and maintenance free Motors run cool, even when running continuously Extremely quiet and smooth running Contamination free pumping of air, gases

and vapours

High tolerance of both vapour and condensate Integrated, flush-fitting handle for easy carrying Wide range of accessories available including

traps and condenser

Compact and portable Easy operation Maintenance-free

Vacuum down to 15mbar Flowrate 5.5 to 30L/min Chemical resistant (KT versions)

PumpsKNF


Self-Drying, Continuous-Cleaning Vacuum PumpsCorrosion resistant, diaphragm, oil-freeKNFs innovative Laboport Self Drying Diaphragm Vacuum Pumps are ideal for applications wheresaturated vapours are being evacuated. This usually causes liquids to collect in the pump, as encounteredwith vacuum ovens, rotary evaporators and gel dryers. Unless removed from the pump they increaseprocessing time and reduce efficiency and pump life. The Laboport Self Drying Pumps cycle every fewminutes, removing accumulated moisture instantly without disturbing the vacuum process.

The unique self-drying process removes accumulated condensate from the pump and restores efficiencywhilst the pump is operating. During the cycle the drying system solenoid opens, permitting air to enterthe evacuated pump head. As a result of the increase in pressure in the pump head, the inlet valve of thefirst stage pump head closes, thus preserving the vacuum level within the evacuated chamber. Bycontrast, the outlet valve, and both valves of the second stage pump head, open automatically causingcondensation to be expelled at high speed. The solenoid valve closes again and the pump now evacuatesthe chamber at full capacity. The drying operation is precisely controlled by an adjustable electronic timer,and set as required.

KNF Laboport pumps feature chemically resistant materials (e.g. PTFE, FFPM) in contact with the gasstream. There are no metal parts to corrode. KNFs moulded structural diaphragm and multiport designensure reliable vacuum performance.

SpecificationsModel N820.3 FT.40.18 N840.3 FT.40.18 N842.3 FT.40.18 N860.3 FT.40.18Flow rate, m3/h (L/min)* 1.2 (20) 2 (34) 2 (34) 3.6 (60)Vacuum, mBar abs 10 10 4 4Pressure, bar 1.0 1.0 1.0 1.0Dimensions (wxdxh), mm 312x177x220 341x189x239 341x189x242 331x291x278.5Weight, kg 9.6 12.9 13.7 14.8

Cat. No. 521-090 521-092 521-094 521-095


* Flow rate at atm. pressure

Diaphragm Vacuum and Pressure PumpsOil-free General purpose laboratory pumps for single or multi flask filtration, pressure filtration and vacuum ovenswith non-aggressive media and other general laboratory uses. Models N 022 AN.18 and N 035 AN.18 areoil-free vacuum pumps or compressors. Model N 035.3 AN.18 is an oil-free higher vacuum pump only. Allpumps are fitted with rubber feet, carrying handles, on-off switch and mains lead with moulded 13 amp plug.

SpecificationsModel N 022 AN.18 N 035 AN.18 N 035.3 AN.18Flow rate, m3/h (L/min) 0.9 (15) 1.8 (30) 1.8 (30)Vacuum, mBar 100 100 13Compression, bar 4 4 Dimensions (wxdxh), mm 203x103x194 265x143x254 294x250x222Weight, kg 4 8.2 11.3Electrical supply 240V/50Hz/60W 240V/50Hz/220W 240V/50Hz/300W

Cat. No. 521-021 521-022 521-024

Price POA POA POA

Accessories

Cat. No. Description For model Price Cat. No. Description For model Price

521-025 Spare kit N 022 AN.18 POA 521-028 Spare kit N 035.3 AN.18 POA

521-026 Spare kit N 035 AN.18 POA

Drying system operates independently ofpumping procedure

Fast, efficient evacuation of saturatedvapours

Drying operation can be adjusted to suit anindividual process

Excellent gas-tightness with PTFE-coateddiaphragm

High suction, small size Portable with retractable handle Maintenance-free and reliable operation Quiet and smooth running High vapour and condensate tolerance Contamination-free pumping of air, gases

and vapours

521-090521-094 521-092

521-022

521-024

521-021

Vacuubrand

Pumps


Diaphragm PumpsVacuubrand diaphragm pumps are totally oil free, mechanical vacuum pumps. Two basic versions are available:

Standard versionThe materials of the wetted parts are made of aluminium, FPM (e.g. Viton) and polyamide. This isadequate for less aggressive gases and vapours.

Chemistry versionAll wetted parts of the chemistry version are made of chemically resistant fluorinated plastic materials, e.g.PTFE-sandwich diaphragms or ECTFE (e.g., Halar) clamping discs with stainless steel core. This makes theChemistry version ideal for rotary evaporation, distillation, vacuum concentration, gel drying etc.

Vacuubrand diaphragm pumps offer high flow rates at low vacuum, excellent reliability and vacuumstability. They are inexpensive and simple to service and maintain. All units are supplied with on/offswitch, mains cable with plug and instructions. The Chemistry versions are also supplied with gas ballast.

Specifications for Standard PumpsModel ME2 ME4 ME4R ME8Maximum flow rate, m3/h (L/min) 1.9 (31) 3.7 (61) 3.6 (56) 6.5 (108)Ultimate vacuum, mbar

PumpsVacuubrand


Chemistry Pumping UnitsThe Vacuubrand laboratory pumping units generate totally oil free vacuum, maintain predeterminedvacuum, control exhaust vapour emissions and allow solvent recovery. The pumping unit components aremade of chemically resistant materials. Units PC510 and PC610 have one vacuum controller, units PC520and PC620 are supplied with two vacuum controllers.

All units are supplied with chemistry diaphragm pump on pump support, catchpot (inlet side) withisolation valve, vacuum controller, air admittance valve, exhaust waste vapour condenser and instructions.

Specifications for Chemistry Controlled Pumping UnitsModel PC510 PC520 PC610 PC620Maximum flow rate, m3/h (L/min) 1.7 (28) 1.7 (28) 3.0 (50) 6.5 (108)Ultimate vacuum, mbar 9 9 2 2Dimensions (lxwxh), mm 400x251x536 400x369x538 400x251x536 400x369x538Weight, kg 18.5 21 25.0 27.5Electrical supply 230V, 50/60Hz 230V, 50/60Hz 230V, 50/60Hz 230V, 50/60Hz

Cat. No. 521-113 521-114 521-115 521-116


For accessories see page 765.

Chemistry Vario Pumping UnitsVario pumping units can precisely maintain a predetermined vacuum level or automatically find theoptimum vacuum/distillation level. They are ideal for rotary evaporators, with virtually 100% solventrecovery, enhanced lifetime and RS232 interface.

All units are supplied with chemistry diaphragm pump mounted on pump support, vacuum controllerCVC2000, catchpot inlet side, exhaust waste vapour condenser and instructions.

Specifications for Chemistry Vario Pumping UnitsModel PC2001 PC2003 PC2004 PC2010Maximum flow rate, m3/h (L/min) 1.5 (25) 1.9 (31) 3.8 (63) 8.2 (136)Ultimate vacuum, mbar 2 0.6 2 0.6Dimensions (lxwxh), mm 310x280x470 400x251x536 400x251x536 650x370x610Weight, kg 9.2 25.0 25.0 37.0Electrical supply 230V, 50/60Hz 230V, 50/60Hz 230V, 50/60Hz 230V, 50/60Hz

Cat. No. 521-117 521-118 521-119 521-120



Chemistry Hybrid PumpChemistry Hybrid Pumps are ideal for fine vacuum chemistry applications such as freeze drying andmolecular distillations.

The oil sealed stages of the pump are constantly evacuated by a chemically resistant two stagediaphragm pump, thus avoiding harmful condensation within this sensitive part of the pump, whilstreducing the partial pressure of the gases and permanently distilling the oil.

All units are supplied with on/off switch, mains cable with plug and instructions.

Specifications for Chemistry Hybrid PumpModel RC5Maximum flow rate, m3/h (L/min) 5.6 (93)Vacuum (partial), mbar 4x10-4

Maximum pressure (total) mbar 2x10-3

Dimensions (lxwxh), mm 505x300x210Weight, kg 25.5Electrical supply 230V, 50/60Hz


521-121 RC5 Chemistry Hybrid pump POA


521-113

521-117

521-121

Vacuubrand

Pumps


Rotary Vane PumpsRotary vane pumps are designed for an ultimate vacuum in the range of 1 mbar to 10-1 (single-stage) or10-3 mbar (two-stage). The rotary vane pump series with integrated oil pump and highly effective gasballast system for improved water vapour tolerance, achieves a powerful combination of performanceand cost effectiveness. These compact and high performance pumps together with their modularaccessories can be used for a wide range of laboratory and process applications.

High conductance inlet - high pumping speed even at low vacuum High vapour tolerance - for water and solvents with gas ballast of about 10% Anti-corrosion design - plasma treated internal surfaces and oil shut-off device to prevent back

flow of gases Quieter operation with longer service intervals - improved lubrication circuit and larger oil reservoir Compact design - smaller dimensions and low weight Reduced power consumption - improved motor design with immediate re-start after shutdown

SpecificationsModel RE2.5 RZ2.5 RE6 RZ6Maximum flow rate, m3/hr (L/min) 2.3/2.8 (47) 2.3/2.8 (47) 5.7/6.8 (113) 5.6 (113)Ultimate vacuum without gas ballast, mbar 3x10-1 2x10-3 1x10-1 2x10-3

Ultimate vacuum with gas ballast, mbar 8x10-1 1x10-2 6x10-1 1x10-2

Water vapour tolerance, mbar 40 40 40 40Water vapour capacity, gh-1 65 65 159 159Dimensions (lxwxh), mm 308x125x190 308x125x190 370x142x207 370x142x207Weight, kg 10.2 11.4 15.3 16.4Electrical supply 230V, 50/60Hz (all models)

Cat. No. 521-122 521-126 521-123 521-127


SpecificationsModel RE9 RZ9 RE16 RZ16Maximum flow rate, m3/hr (L/min) 8.6/9.9 (165) 8.6 (165) 16.6/19.1 16.6/19.1

(318) (318)Ultimate vacuum without gas ballast, mbar 1x10-1 2x10-3 1x10-1 2x10-3

Ultimate vacuum with gas ballast, mbar 6x10-1 1x10-2 6x10-1 1x10-2

Water vapour tolerance, mbar 40 40 40 40Water vapour capacity, gh-1 246 246 474 474Dimensions (lxwxh), mm 460x152x232 460x152x232 505x152x232 545x152x232Weight, kg 22.1 24.6 25.2 29Electrical supply 230V, 50/60Hz (all models)

Cat. No. 521-124 521-128 521-125 521-129



521-126New

521-127New

521-128New

PumpsVacuubrand


Pump AccessoriesInlet Separators and Oil Mist Filters

Inlet separator - to protect pump from particulate matter both in liquid and solid form.

Oil mist filter - prevents loss of oil to atmosphere and reduces condensate build up in pumps.

Cat. No. Description For Model Price

521-130 Inlet separator RE2.5/RZ2.5 POA

521-131 Inlet separator RE6/RZ6 POA

521-132 Inlet separator RE9/RZ9, RE16/RZ16 POA

521-177 Oil mist filter RE2.5/RZ2.5, RE6/RZ6 POA

521-178 Oil mist filter RE9/RZ9 RE16/RZ16 POA

Cold Traps GKF 1000i - glass cold trap with mirror insulated jacket, PTFE stopcock, sight strip and implosion protection.

SKF H - stainless steel cold trap offers excellent cooling properties, is easy to drain, disassemble and clean.

Cat. No. Description Connections For Model Price

521-133 GKF 1000i, glass Pump side 22mm o.d. RE2.5/RZ2.5 POAPlant side NS29/32 glass joint

521-134 SKF H 25, stainless steel NW25 RE6/RZ6 POA

521-135 SKF H 40, stainless steel NW40 RE9/RZ9, RE16/RZ16 POA

Chemically resistant gauges and controllers

Specifications for Gauges and ControllersModel DVR2 DVR5 VAP5 CVC211*Type Rough vacuum Rough vacuum Fine vacuum Rough vacuum

gauge gauge gauge controllerMeasuring range, mbar 1080 to 1 1100 to 0.1 1000 to 10-3 1300 to 1Uncertainty of measurement, mbar

Ilmvac

Pumps


521-150 PK Series Rotary Vane Vacuum PumpsExtremely compact and quiet rotary vane type vacuum pumps. With high vapour tolerance and a rangeof solvent and acid handling accessories these pumps are ideal for freeze drying and general laboratoryapplications.

Compact design High tolerance to chemical processes Very quiet operation

Supplied with oil, mains lead and plug and gas ballast valve. Other models with various flow rates andultimate vacuums available.

Specifications Model PK2DC PK4Dp PK6Dp PK8DpFlow rate, m3/hr (L/min) 1.8 (30) 4.6 (76) 6.4 (106) 8.3 (138)Ultimate vacuum, mbar

PumpsIlmvac


512-312PK4DpX Rotary Vane Vacuum PumpGeneral purpose laboratory vacuum pump designed for high vapour tolerance and incorporating intakeseparator and exhaust side oil mist eliminator. The pump is pre-filled with oil (oil capacity: 500ml) andhosetail connections are also included to enable the pump to be used straight out of the box.

Compact design High tolerance to chemical processes Very quiet operation

Supplied with oil, mains lead and plug, inlet and outlet 12mm nozzles, exhaust mist filters and inletcatch-pot.

Specification Flow rate, m3/hr (L/min) 4.6 (76)Ultimate vacuum, mbar 2x10-4

Water vapour tolerance, mbar 40Motor power, kW 0.37Separator on intake side Glass catch-pot, nickelised aluminium connection, mounted to side of

pump bodyOil mist eliminator, exhaust side Glass catch-pot with coalescing filter media and over-pressure protec-

tion, nickelised aluminium connection, mounted to side of pump bodyConnections intake and outlet DN16KF flange supplied with 12mm hose nozzle, clamp and sealDimensions (wxdxh), mm 405x150x200Weight, kg 19Electrical supply 230V, 50/60Hz


521-312 PK4DpK Two stage rotary vane pump POA

Accessories


521-308 OPF40C Acid neutralising external oil filter POA

HBP100 Hold-Back-Pump for Vacuum DistillationThe HBP100 is a new and unique solution for solvent evaporation and condensation. It provides acomplete, automatically controlled vacuum pump and condenser unit at considerable capital cost savingsover conventional solutions.

Specification Pumping speed, L/min (m3/hr) 2.3 (40)Ultimate vacuum, mbar 10, self-regulatingVacuum connection hose nozzle DN10 for 10mm ID tubingExhaust connection clamping union for 6mm ID tubingWater connections clamping union for 6mm ID tubingSolvent collection vessel round flask 1000ml with S35 joint and clampNoise level

Ilmvac

Pumps


MPC-Series, Full PTFE Construction Diaphragm PumpsA highly cost efficient range of PTFE diaphragm pumps. The diaphragm and all parts coming into contactwith the vapours are PTFE or PTFE-compounds. Supplied ready for use with a 2 year warranty.

All wetted parts made from PTFE materials Suitable for pumping solvent and acid vapours Optimised for high flow rate and stable final vacuum Long lasting, self cleaning valves made of PEEK Low noise and vibration Drive and bearing isolated from air cooling stream 8mm hose tails (options on request) 10,000 hour service interval and 2 year warranty Low cost spares and easy servicing Applications include: distillation, non-aqueous filtration, gel drying, rotary evaporators,

centrifugal evaporations

Supplied with carry handle, mains lead and plug, gas ballast valve, exhaust silencer and 8mm inlet andoutlet nozzles.

Specifications Model MPC102E MPC201E MPC601E MPC1201E MPC2401EFlow rate, m3/hr (L/min ) 0.8 (13) 1.8 (30) 3.8 (63) 8.3 (138) 15.5 (258)Ultimate vacuum, mbar

PumpsIlmvac


521-511MP Series, Diaphragm PumpsA low cost range of diaphragm pumps for general applications not requiring chemical resistance.Supplied ready for use with a 2 year warranty.

Aluminium construction Low noise and vibration Optimised for high flow rate and stable final vacuum 8mm hose tails (options on request) 10,000 hour service intervals and 2 year warranty Low cost spares and easy servicing Applications include: Aqueous filtration, vacuum tweezers, vacuum ovens, general applications

to 1 mbar

Pumps are supplied ready to use with carrying handle, mains lead and plug, 8mm inlet connection andexhaust silencer.

Specifications Model MP102E MP201E MP601E MP1201E MP2401EFlow rate, m3/hr (L/min ) 0.8 (13) 1.8 (30) 3.8 (63) 8.3 (138) 15.53 (258)Ultimate vacuum, mbar

Ilmvac

Pumps


521-563New

521-564New

521-567New

521-573New VCB324 Vacuum ControllerA complete vacuum control solution for any vacuum source. All the components are contained in asingle compact unit ready for use. Simply connect via tubing to a vacuum pump or bench outlet, couplevia tubing to your process and you have a fully featured controlled vacuum source.

No trailing wires or clamp stands Manual and automatic boiling point determination Easy, on-the-fly adjustments Static memory for reproducible results RS232 remote control and data-logging Easy cleaning, virtually maintenance free 2 year warranty

This unique product is supplied fully configured and ready to use. Tubing connection for vacuum andprocess are 8mm hose barbs.

SpecificationMeasuring range, mbar 1100 to 1Accuracy, mbar 2Display LED in mbars and torsDimensions (wxdxh), mm 200x170x165Thresholds/output at front panel 24V DC 10W per channel, 30W totalVacuum connection at sensor female thread 1/4 inch, DN 16 KFWeight, kg 1.5Electrical supply 90-240V, 50-60Hz, 40W


521-573 VCB324 Vacuum controller POA

Chemvac Series, High Vacuum Pumps for Chemical ApplicationsA unique range of high vacuum pumps designed to prevent solvent condensation in the pump oil. Thecombined oil and diaphragm stages give the benefits of rotary vane pump vacuum levels with PTFEdiaphragm pump chemical resistance.

High resistance to solvent and acid vapours Extremely long oil change and service intervals External oil filtering available for acid neutralization Inter-stage catch-pots retain solvents Applications include: Freeze drying of non-aqueous samples, centrifugal concentrators, drying

ovens, high vacuum distillations 2 year warranty

Pumps are supplied ready to use, charged with oil, with mains lead and plug, inter-stage catch-pots andKF16 or KF25 connections.

Specifications for pumps with one rotary vane stage and two PTFE diaphragm stagesModel 4S-101 8S-101 12S-101 17S-101 23S-101Flow rate, m3/hr (L/min) 3.7 (62) 7.3 (120) 11.0 (183) 16.0 (266) 21.0 (350)Ultimate vacuum, mbar

PumpsIlmvac


LVS Series, Laboratory Vacuum SystemsThe latest solutions for solvent handling in the laboratory, LVS units are based on the MPC range ofchemically resistant diaphragm pumps with solvent containment condensers. They are available with orwithout control. There are four control options available:

None: The vacuum level is not controlled.

Standard Valve: The vacuum pump operates continuously and the process vacuum level is controlledby a chemically resistant solenoid valve. Set points can be preset, altered during the process, ordetermined automatically using the boiling point finding facility.

Management: The pump starts and stops automatically to maintain vacuum within your set range.Ideal for operating vacuum lines and networks where service intervals are greatly extended.

Ecoflex: The pumps flow rate is automatically varied to maintain the set point by matching the vapourload. Set points can be preset, altered during the process, or determined automatically using the boilingpoint finding facility. Ideal for rotary evaporators, where process times can be reduced by up to 30%.Service intervals are greatly extended. VCZ324 controller included.

Only PTFE compounds and glass in contact with the vapour stream Solvent containment to approximately 98% Small footprint Interchangeable vacuum pumps for future flexibility 10,000 hour service intervals and 2 year warranty RS232 facility and data-logging control software available

Systems are supplied ready to use with pump, inlet catch-pot, water cooled emission condenser, mainslead and plug. Optional control modes fully installed where selected.

521-538 New

Specifications - Two stage vacuum systems with no control or standard valve controlModels LVS 0501 LVS 101 LVS 300 LVS 310

LVS 0501RM LVS 101RM LVS 301 LVS 311LVS 0510 LVS 110 LVS 302 LVS 320

Flow rate, m3/hr (L/min ) 0.4 (8) 1.0 (17) 2.3 (38) 2.3 (38)Ultimate vacuum, mbar

Ilmvac

Pumps


LVS Series, Laboratory Vacuum Systems, continuedTwo-stage Laboratory Vacuum Systems with no control or standard valve control


521-535 LVS 0501 Laboratory vacuum system with MPC 052Z pump, one uncontrolled connection POA

521-536 LVS 0501 RM Laboratory vacuum system with MPC 052Z pump, manometer, one uncontrolled connection POA

521-537 LVS 0510 Laboratory vacuum system with MPC 052Z pump, controller POAcomplete module with external sensor, airing valve, one controlled connection


521-539 LVS 101 RM Laboratory vacuum system with MPC 101Z pump, manometer, one uncontrolled connection POA


521-541 LVS 300 Laboratory vacuum system with MPC 301Z pump POA


521-543 LVS 302 Laboratory vacuum system with MPC 301Z pump, two uncontrolled connections POA


521-545 LVS 311 Laboratory vacuum system with MPC 301Z pump, controller POAcomplete module with external sensor, airing valve, one controlled and one uncontrolled connection

521-546 LVS 320 Laboratory vacuum system with MPC 301Z pump, controller POAcomplete module with external sensor, airing valve, two controlled connections

Three-stage Laboratory Vacuum Systems with no control or standard valve control


521-547 LVS 201T Laboratory vacuum system with MPC 201T pump, one uncontrolled connection POA

521-548 LVS 210T Laboratory vacuum system with MPC 201T pump, controller POAcomplete module with external sensor, airing valve, one controlled connection

521-549 LVS 601T Laboratory vacuum system with MPC 601T pump, one uncontrolled connection POA

521-550 LVS 602T Laboratory vacuum system with MPC 602T pump, two uncontrolled connections POA


521-552 LVS 611T Laboratory vacuum system with MPC 601T pump, controller POAcomplete module with external sensor, airing valve, one controlled and one uncontrolled connection

521-553 LVS 620T Laboratory vacuum system with MPC 601T pump, controller POAcomplete module with external sensor, airing valve, two controlled connections


Two-stage Laboratory Vacuum Systems with Management or Ecoflex System


521-555 LVS 110M Laboratory vacuum system with MPC 101Z pump and management system POA

521-556 LVS 310M Laboratory vacuum system with MPC 301Z pump and management system POA

521-559 LVS 310E Ecoflex laboratory vacuum system with MPC 301Z pump and VCZ324 controller POA

Three-stage Laboratory Vacuum Systems with Management or Ecoflex System


521-560 LVS 210TE Ecoflex laboratory vacuum system with MPC 201T pump and VCZ324 controller POA

521-557 LVS 610TM Laboratory vacuum system with MPC 601T pump and management system POA


521-558 LVS 1210TM Laboratory vacuum system with MPC 1201T pump and management system POA


For details on accessories, including service kits please contact our Technical Office on 01342 826836.

Pumps


451-150

Ilmvac, PLS301Z Diaphragm Pump SystemOil-free, mechanical vacuum pump, mounted on pump holder, with intake-side separator, delivery-sideemission condenser cooled by dry ice slurry.

Suitable for all applications between atmosphere and 8 mbar absolute including rotary and centrifugalevaporation, gel drying, filtration, drying ovens, desiccators and more.

Specification Flow rate, m3/hr (L/min) at 1000 mbar/20 mbar 2.3 (40)/1.4 (23)

Ultimate pressure, mbarWithout gas ballast 8

Construction Pump: carbon-fibre reinforced PTFE pump head, electrically conductive Sandwich diaphragm, fabric reinforced with a PTFE layer Materials coming into contact with the media are resistant to chemicals (PVDF, PEEK) Built-in gas ballast valve Special feet for isolating the pump vibrations

Separator, on intake side Round-bottomed glass flask, 500ml (coated)Emission condenser, on Glass demountable CO2 trap with removable well and lid delivery side 100% restricted guidance of the pumped medium

without by-pass beneath the cooling surface Collection flask 500 ml

Connections Intake: DN10 clamping ring screw fittings Outlet: DN10 clamping ring screw fittings Cooling water: 2x DN8 ports

Dimensions (wxdxh), mm 310x270x500Weight, kg 18.5Electrical supply 230V, 50HzCE conformity M-RL, NS-RL, EMC


521-313 PLS301Z Diaphragm pump system POA

Pfeiffer, Rotary Vane PumpsThese innovative double stage rotary vane pumps are suitable for all applications in the rough andmedium vacuum range, featuring pumping speeds of 80 to 160L/min. The drive concept integratedmagnetic coupling ensures that the pumps are hermetically sealed. Separating the rotor and motorshafts solves the problem connected with rotary shaft seals. The wear-free drive prevents leaks, keepsmaintenance to a minimum and considerably lengthens the pumps working life.

Pfeiffer rotary vane pumps also offer more process safety, with the high speed high vacuum safety valveintegrated as standard. This fast, hydraulically-controlled valve stops the pump immediately in the eventof faults such as power failure, undervoltage or process safety cutoff. Supplied with operating lubricant.

SpecificationsModel DUO 005M DUO 010MNominal pumping speeds, m3/h (L/min) 4.8 (80) 9.7 (160)Ultimate vacuum, mbarwithout gas ballast/with gas ballast

Heidolph

Pumps


Peristaltic Pump Drives and HeadsThe Heidolph range includes 6 drives, 4 peristaltic pump heads and 3 multi-channel pump heads.Peristaltic pump drives are available with and without serial and analogue interfaces. They are ideal foraggressive, abrasive or corrosive solvents and sterilised media. Flow rates from 0.3ml up to 3,644ml perminute are available (H20), as are double pump head systems.

No contamination as fluid is in contact with the tubing only Superior for transport of high viscous media up to 10,000cP Self-priming and come without valves and seals Easily function under pressure and vacuum Various chemically resistant and sterilisable tubes available for individual applications Interval dosing available (models PD 5201 and PD 5206 only) 3 year warranty

PD 5001 and PD 5006 Pump Drives These peristaltic pump drives are suitable for standard applications; they have electronic speed control(accuracy 2%), large dials for speed setting, protection to IP30 and can be stacked (up to 3 pumpdrives). Flow can be clockwise or counter clockwise.

The PD 5001 provides flow rates from 0.7 to 729ml per minute with a speed range of 10 to 120rpm. Itcan also be equipped with two pumps heads (SP quick and SP quick d) or with a multi-channel pumphead (C4, C8 or C12 - an adaptor is required but not supplied). Multi-channel flow rates are from 0.01to 336ml/min.

Model PD 5006 provides flow rates from 3.3 to 3,644ml per minute with a speed range of 50 to 600rpm.It is suitable for any of the single pumps heads, however it is not suitable for the use of multi-channelpump heads.

PD 5101 and PD 5106 Pump Drives These models are designed for more demanding applications. Both pump drives have an analogueinterface for speed range setting, direction of rotation and start/stop function. They have electronicspeed control (accuracy 0.5%), large dials for speed setting, protection to IP55 and can be stacked (upto 3 pump drives). Flow can be clockwise or counter clockwise and the filling and emptying of tubing canbe accelerated by a push-button.

The PD 5101 provides flow rates from 0.3 to 729ml per minute with a speed range of 5 to 120rpm. It canalso be equipped with two pumps heads (SP quick and SP quick d) or with a multi-channel pump head(C4, C8 or C12 - an adaptor is required but not supplied). Multi-channel flow rates are from 0.005 to336ml/min.

Model PD 5106 provides flow rates from 1.6 to 3,644ml per minute with a speed range of 24 to 600rpm.It is suitable for any of the single pumps heads, however it is not suitable for the use of multi-channelpump heads.

PD 5201 and PD 5206 Pump Drives Both the PD 5201 and PD 5206 pump drives have an analogue and digital RS232 interface for speedrange setting, direction of rotation and start/stop function. They feature a four-digit display for electronicspeed setting, electronic speed control (accuracy 0.5%), protection to IP 55 and they can be stacked (upto 3 pump drives). The four-digit display is also used for flow rate setting, interval dosing and pausesetting. Flow can be clockwise or counter clockwise and the filling and emptying of tubing can beaccelerated by a push-button. Other features include:

Calibration of flow rate and flow volume Microprocessor controlled drive Flow rates of the pump heads in combination with the various tubing are saved in the program

to enable direct digital readout of flow rate In addition to the flow rate readout, it is possible to pre-select a dosing volume Interval dosing is possible by entering a time interval

Pump drive PD 5201 provides flow rates from 0.3 to 729ml per minute with a speed range of 5 to120rpm. It can also be equipped with two pumps heads (SP quick and SP quick d) or with a multi-channelpump head (C4, C8 or C12 - an adaptor is required but not supplied). Multi-channel flow rates are from0.005 to 336ml/min.

Model PD 5106 provides flow rates from 1.6 to 3644ml per minute with a speed range of 24 to 600rpm.It is suitable for any of the single pumps heads, however it is not suitable for use with multi-channelpump heads.





PumpsHeidolph


Peristaltic Pump Drives and Heads, continuedSpecificationsModel PD 5001 PD 5006 PD 5101 PD 5106 PD 5201 PD 5206Flow rate ranges, ml/min 0.7729 3.33644 0.3729 1.63644 0.3729 1.6-3644Flow rate - multi-channel 0.01336 N/A 0.005336 N/A 0.005336 N/Apump, ml/minSpeed range, rpm 10120 50600 5120 24600 5120 24600Dimensions (wxhxd), mm 166x225 166x225 166x225 166x225 166x225 166x225

x256 x256 x256 x256 x256 x256Weight, kg 6.8 6.2 8.2 7.6 8.3 7.7


521-600 PD 5001 pump drive POA






Pump drives are supplied without a pump head or tubing. Please see below for details.

Single-Channel Peristaltic Pump HeadsSP quick and SP quick d Pump HeadsDesigned for fast and convenient tube changes and suitable for tubing with a 1.6mm or 2.5mm wallthickness. The flow rate ranges from 0.3 to 3,300ml per minute depending on drive and tubing. Toattach two pump heads to one drive unit, choose SP quick in combination with SP quick d.

Designed for cleaning in industrial washing machines Low pulsation due to 5 roller system Pump head features ball bearings Rollers made of stainless steel

SpecificationsModel SP quick 1.6 SP quick 2.5 SP quick d 1.6 SP quick d 2.5Flow rate ranges, ml/min 0.32217 11.23300 0.32217 11.23300Tubing wall thickness, mm 1.6 2.5 1.6 2.5Number of rollers 5 5 5 5


521-630 SP quick 1.6 pump head POA

521-631 SP quick 2.5 pump head POA

521-632 SP quick d 1.6 pump head POA

521-633 SP quick d 2.5 pump head POA

To attach two pump heads to one drive unit, choose SP quick in combination with SP quick d.

SP standard Pump Head Recommended for standard applications and suitable for tubing with a 1.6mm or 2.5mm wall thickness.The flow rate ranges from 0.5 to 3,344ml per minute depending on drive and tubing.

Recommended for standard applications High pulsation due to 2 roller system Pump head features ball bearings Rollers made of stainless steel and polyamide Convex rollers do not squeeze or crush organic cell cultures

SP vario Pump HeadSuitable for most Heidolph tubing due to adjustable roller spacing. The flow rate ranges from 0.5 to3,344ml per minute depending on drive and tubing.

Direction of rotation clockwise only Rotor is removable for cleaning purposes High pulsation due to 2 roller system Pump head features ball bearings Rollers made of stainless steel and aluminium Convex rollers do not squeeze or crush organic cell cultures

521-604 shown with 521-631 New

521-605 shown with 521-634 New

521-631 New

521-631 with 521-633 New

521-633 New

Heidolph

Pumps


Peristaltic Pump Drives and Heads, continuedSpecificationsModel SP standard 1.6 SP standard 2.5 SP varioFlow rate ranges, ml/min 0.53644 17.33644 0.53644Tubing wall thickness, mm 1.6 2.5 Various*Number of rollers 2 2 2

Cat. No. 521-634 521-635 521-636

Price POA POA POA

* Suitable for most Heidolph tubing due to adjustable roller spacing. For more information please contact ourTechnical Office on 01342 826836.

Multi-Channel Peristaltic Pump Heads There is a choice of three multi-channel pump heads which accept 4, 8 or 12 cassettes. The feed rate ofeach channel can be adjusted by using different tubing dimensions. Tubing is available in a variety ofmaterials and sizes and can be changed easily. Other features include 4 or 8 rollers for minimal pulsationand cassettes may be changed during operation. Cassettes must be ordered separately.

C4 Multi-Channel Pump Head The C4 pump head has 8 rollers for low-pulsation and accepts 4 small cassettes. Cassettes may bepartially used and click easily into place.

C8 Multi-Channel Pump Head This model has a 4-roller design and accepts 8 medium or 4 large cassettes. Medium and large sizecassettes may be used together. Cassettes may be partially used and click easily into place.

C12 Multi-Channel Pump Head The C12 pump head has 8 rollers for low-pulsation and accepts 12 small cassettes. Cassettes may bepartially used and click easily into place. Built-in reduction gear allows feeding of smallest quantities.


521-637 C4 Multi-channel pump head POA



521-643 Adaptor for multi-channel pump heads* POA521-640 Small cassette for C4 and C12 pump heads POA

521-641 Medium cassette for C8 pump head POA

521-642 Large cassette for C8 pump head POA

* A multi-channel adaptor is required to connect the pump drives PD 5001, PD 5101 and PD 5201 to a multi-channelpump head (pump drives PD 5006, PD 5106 and PD 5206 are not suitable for use with multi-channel pump heads). Also,if you already have a Heidolph single drive pump an adaptor is required to connect this to a multi-channel pump head.

Peristaltic Tubing for Single-Channel Pump Heads Supplied in lengths of 1m, wall thickness 1.6mm.

Flow rates (ml/min) of pump drives with single-channel pump headsTubing bore, mm 0.8 3.1 6.3

SP quickPD 5106/5206 1.640 25.7643 88.72217PD 5006 3.340 53.6643 184.82217PD 5101/5201 0.38.0 5.2129 17.7443PD 5001 0.78.0 10.7129 37.0443

SP standard/SP VarioPD 5106/5206 2.460.2 41.21029 1463644PD 5006 5.060.2 85.81029 3043644PD 5101/5201 0.512.0 8.2206 29.2729PD 5001 1.012.0 17.2206 60.7729

Silicon Cat. No. 521-606 521-607 521-608

Price POA POA POA

Tygon Cat. No. 521-609 521-610 521-611

Price POA POA POA

Other tubing sizes are available including, 1.7mm and 4.8mm. The following tube sizes are also available with a wallthickness of 2.5mm: 4.8, 6.3 and 7.9mm. For details on these and other tubing materials (Viton, PharMed, Tygon

(hydrocarbon, food)) please contact our Technical Office on 01342 826836 for details.

521-638New521-637New

521-636New521-634New

521-641New

521-642

521-640New

521-639New

New

521-643New

PumpsHeidolph


Silicon tubingPeristaltic Tubing for Multi-Channel Pump Heads Three-stop tubing is supplied in lengths of 40cm. Extension tubing is supplied in lengths of 1m.

Flow rates (ml/min) of pump drives, pump heads with cassettesTubing bore, mm 0.2 0.5 0.9 1.4 2.8

PD 5101/ 5201Cassette small/pump head C12* 0.0050.12 0.020.5 0.051.24 0.112.8 0.338.2Cassette small/pump head C4** 0.0240.60 0.112.5 0.256.24 0.5613.9 1.6340.8PD 5001Cassette small/pump head C12* 0.010.12 0.040.5 0.101.24 0.232.8 0.688.2Cassette small/pump head C4** 0.050.60 0.212.5 0.526.24 1.1613.9 3.4040.8

Silicon

Three-stop tubing for Small CassetteCat. No. 521-612 521-613 521-614

Price POA POA POA

Extension tubingCat. No. 521-615 521-616 521-617

Price POA POA POA

Tygon

Three-stop tubing for Small CassetteCat. No. 521-618 521-619 521-620 521-621 521-622

Price POA POA POA POA POA

Extension tubingCat. No. 521-623 521-624 521-625 521-626 521-627

Price POA POA POA POA POA

* Maximum number of cassettes: 12. ** Maximum number of cassettes: 4.


521-628 Fitting for extension tubing (PTFE) for 0.2, 0.5, 0.9 and 1.4mm tubing POA

521-629 Fitting for extension tubing (PTFE) for 2.8mm tubing POA

The fittings for extension tubing are supplied in a pack size of one. Therefore a minimum of two should be orderedto connect extension tubing on both sides of the three-stop tubing.

Flow rates 1 ml/min of pump drives, pump heads with cassettesTubing bore, mm 0.8 3.1 6.3

PD 5101/ 5201Cassette medium/pump head C8* 0.297.2 Cassette large/pump head C8** 3.896.0 13.5336PD 5001Cassette medium/pump head C8* 0.67.2 Cassette large/pump head C8** 8.096.0 28.0336* Maximum number of cassettes: 8. ** Maximum number of cassettes: 4.

This is the same tubing as listed for the single-channel pump heads, please see previous page for pricing and orderingdetails.

Other tubing sizes are available including, 1.7mm and 4.8mm. For details on these and other tubing materials(Viton, PharMed, Tygon (hydrocarbon, food)) please contact our Technical Office on 01342 826836 for details.

New

Tygon tubing New

521-628 New

Three-stop tubing

New

Watson Marlow

Pumps


519-000 101U/R Auto/ Manual Control, Variable Speed Peristaltic PumpLow flow variable speed pump which is ideal for small volume, single channel applications includingfermenter feed.

Instant changeover between manual and analogue auto control. Fitted with rapid tube loading 102Rpumphead which accepts silicone tubing.

SpecificationFlow rate ranges (ml/min)for tube bore, mm 0.5 0.8 1.6 3.2 4.8at 1.0-32 rpm 0.0210.69 0.0481.61 0.2107.00 0.78026.0 1.59053.0

Speed range, rpm 1.032Dimensions (hxwxl), mm 100x160x210Weight, kg 2.4Standards BS800, IEC 335-1, EN60529 (IP31), CE


519-000 101U/R Auto/manual control, variable speed peristaltic pump POA

For silicone tubing see page 779.

323 Series Manual/ Remote/ Auto Control, Single/MultipleChannel PumpsA range of pumps with manual, remote or auto control through a single channel and flow rates up totwo L/min, or through up to ten channels using manifold tubing for microlitre flows.

Details are given here for 323 drives fitted with 313D single channel pumpheads which can be extendedup to a maximum of six individual channels. For microlitre flows, 323 drives can also be fitted with thefour roller 314MC pumphead, or eight roller 318MC pumphead. These pumpheads have five individualcassettes which accept double segment manifold tubing and can be extended by one pumphead toprovide a maximum of ten channels.

323S/D high-performance manual control variable speed pumps Flows rates to 2L/min per channel Snap-fit 313X extension pumpheads provide up to six channels Keypad lock prevents tampering or accidental changes Two year comprehensive warranty

323S/D speed adjusts in 1rpm steps from 3 to 400rpm. Instantly reversible, rapid-loading flip-toppumphead accepts seven tube sizes, keypad lock prevents tampering or accidental changes, auto restartfor mains failure recovery.

323U/D analogue auto/manual control variable speed pumpSame specification as 323S/D above but with remote 420mA or 010V analogue auto-control via aplug-in control card mounted on the rear panel.

SpecificationFlow rate ranges (ml/min)tube bore 0.5 0.8 1.6 3.2 4.8 6.4 8.03.0-400rpm 0.0912 0.2128 0.81110 3.0400 6.6880 111400 152000

Speed range, rpm 3.0400rpmPumphead fitted 313D three roller pumpheadDimensions (hxwxl), mm 125x230x225Weight, kg 4.7Standards IEC 335-1, EN60529 (IP31), CE


519-008 323S/D Manual control variable speed pump POA

519-030 323U/D Analogue auto/manual control variable speed pump POA

519-031 323S/D Manual control variable speed pump, drive only* POA519-032 323U/D Analogue auto/manual control variable speed pump, drive only* POA519-033 313X Three roller extension pumphead (maximum of 5) POA

* Order the drive only to enable 314MC or 318MC pumpheads to be fitted, see next page.For tubing also see next page.

Flow rates from 0.001 to 53ml/min Reversible flow with Max priming switch

Accepts auto-control signals up to 30V or32mA and TTL remote control pumphead

Two year comprehensive warranty

519-008

519-034

PumpsWatson Marlow


323 Series, continuedCassette pumpheads for microlitre flow ratesFor low-flow pumping through up to ten channels, 323S and 323U drives may be fitted with 314MC(four-roller) and 318MC (eight-roller) microcassette pumpheads, which can be extended to ten channelsby adding one 314MCX or 318MCX extension pumphead. 314MC four-roller higher-flow five channel cassette pumphead 314MCX four-roller extension pumphead add one to 314MC for ten channel pumping 318MC eight roller higher-accuracy five channel cassette pumphead 318MCX eight roller extension pumphead add one to 318MC for ten channel pumping


519-034 314MC four-roller pumphead POA

519-036 318MC eight-roller pumphead POA

519-035 314MCX four-roller extension pumphead (maximum one extension pumphead) POA

519-037 318MCX eight-roller extension pumphead (maximum one extension pumphead) POA

Double pump segment manifold pump tubing for 314MC and 318MC microcassette pumpheads314MC and 318MC pumphead flow rate ranges (ml/min) - maximum 10 channels. Note: Speed mustnot exceed 110rpm.

Flow rates (ml/min) at 3.0-110 rpm for 323S and 323U drives

Description Cat. No. Price Cat. No. Price

Colour code Bore Marprene (Pack of 6) PVC (Pack of 12)

Orange/Blue 0.25mm 519-047 POA 519-048 POA

Orange/Yellow 0.50mm 519-049 POA 519-050 POA

Black/Black 0.76mm 519-051 POA 519-052 POA

Orange/Orange 0.88mm 519-053 POA 519-054 POA

Red/Red 1.14mm 519-055 POA 519-056 POA

Grey/Grey 1.29mm 519-057 POA 519-058 POA

Yellow/Blue 1.52mm 519-059 POA 519-060 POA

Green/Green 1.85mm 519-061 POA 519-062 POA

Purple/Black 2.29mm 519-063 POA 519-064 POA

Purple/White 2.79mm 519-065 POA 519-066 POA

Peristaltic Pump Tubing Supplied in lengths of 15m.

Pumpsil

Platinum-cured Silicone tubing manufactured by Watson-Marlow.

Tighter bore and wall tolerances (no negative tolerance) ensure flow stability and accuracy LaserTraceability, laser etched lot number full length of tubing ensures true traceability Pumpsil meets or exceeds : USP class VI; European Pharmacopoeia 3.1.9; ISO 10993; FDA

regulations CFR 177.2600 for contact with food; USDA standards; 3A standards

Marprene

Cat. No. Bore, mm Price

519-011 0.5 POA

519-012 0.8 POA

519-013 1.6 POA

519-014 3.2 POA

519-015 4.8 POA

519-016 6.4 POA

519-017 8.0 POA

Silicone


519-018 0.5 POA

519-019 0.8 POA

519-020 1.6 POA

519-021 3.2 POA

519-022 4.8 POA

519-023 6.4 POA

519-024 8.0 POA

Bioprene


519-040 0.5 POA

519-041 0.8 POA

519-042 1.6 POA

519-043 3.2 POA

519-044 4.8 POA

519-045 6.4 POA

519-046 8.0 POA

314MC 318MCOrange/Blue 0.25mm 0.010.5 0.010.5Orange/Yellow 0.50mm 0.051.7 0.041.4Black/Black 0.76mm 0.134.6 0.113.9Orange/Orange 0.88mm 0.176.4 0.145.3Red/Red 1.14mm 0.279.9 0.248.8

314MC 318MCGrey/Grey 1.29mm 0.3513 0.2710Yellow/Blue 1.52mm 0.5219 0.3814Green/Green 1.85mm 0.7628 0.5520Purple/Black 2.29mm 1.140 0.7929Purple/White 2.79mm 1.453 0.9836

Bioprene tubing

Pumpsil PlatinumSilicone tubing

Marprene tubing

Watson Marlow

Pumps


519-084 520 Series PumpsThe new 520 range from Watson-Marlow allows the pumps to be matched to the task for accurateresults without compromise, now and in the future. The high-flow 520R pumphead and maintenancefree brushless high powered drives provide the best performance, long life and great value.

520S/R Manual Control Variable Speed PumpsFitted as standard with the new pumphead 520R. It features large swept volume with sprung stainlesssteel rollers for high accuracy and gentle pumping of shear sensitive fluids. Low rotational speeds greatlyincrease tube life and system reliability.

* Also accepts 520R 2.4mm wall tubing pumphead for maximum flow and other multi-channel pumphead options.

Flow rates ranges (ml/min) for 1.6mm wall tubingTube bore 1.6 3.2 4.8 6.4 8.00.1 to 220rpm 0.0497 0.18390 0.40870 0.701500 1.12400Dimensions (hxwxl), mm/Weight, kg 158x276x385 (all models)/9.6 (all models)Power 135VA (all models)Standards: CE, CETL US (all models)


519-084 520S/R Manual control variable speed pump POA

520U/R Auto/Analogue, Manual Control Variable Speed PumpThe 520U/R shares all the features of the 520S/R plus:



519-085 520U/R Auto/analogue, manual control variable speed pump POA

520Du/R Digital /Analogue Manual Control Variable Speed PumpThe 520Du/R shares all the features of the two models above plus:

* Also accepts 520R2 pumphead for use with 2.4mm wall thickness tubing and other multi-channel pumphead options.



519-086 520Du/R Digital/analogue manual control variable speed pump POA

For tubing see page 779.

Flow rates from 4 microlitres/min up to 3.5litres/min * in 0.1rpm steps

Digital RS 485 control

Mimic control of stoke length/speed ofdiaphragm/piston pump

Inputs: Analogue 010V/420mA softwareconfigurable and calibrated, 010V ana-logue or 01258Hz speed indication output

Inputs: Run/stop, direction, leak detected,auto/manual toggle, MemoDose remotefoot switch, all accepting 5VTTL or 24Vindustrial logic

Outputs: 4 status outputs, 5V TTL or 24Vindustrial logic, user set-up for run/stop,direction, auto/manual status and choice ofalarm conditions

* Also accepts 520R 2.4mm wall tubing pumpheadfor maximum flow and other multi-channel pumphead options.

Flow rates from 4 microlitres/min up to 3.5 litre/min*

Brushless motor, high power and precisionspeed control

Large digital display and easy to use tactilemembrane keypad. Incorporates keypad lock

Manual control and flow calibration MemoDose for accurate single shot dispensing Dual voltage, 115V/230V 50/60Hz and

24 hour duty rated Stackable 3 year comprehensive warranty

New

519-085New

519-086New

Untitled

pumps

Documents

lmin pump flow rate

approx flow rate

high flow rates

mbar rotary evaporators

mbar cell

mbar desiccation

mbar aspiration

pump selection