pulse modulation

16
COMS3100/7100 Introduction to Introduction to Communications Lecture 15: Pulse Modulation This lecture: PulseAmplitude Modulation PulseTime Modulation PulseDuration and PulsePosition Modulation Ref: Carlson, Chapter 6.26.3; Haykin, Chapter 3.33.4

Upload: mani-kandan

Post on 20-Nov-2014

961 views

Category:

Documents


3 download

TRANSCRIPT

Page 1: Pulse Modulation

COMS3100/7100Introduction toIntroduction to Communications

Lecture 15: Pulse Modulation

This lecture:

Pulse‐Amplitude Modulation

Pulse‐Time ModulationPulse‐Duration and Pulse‐Position Modulation

Ref: Carlson, Chapter 6.2‐6.3;  Haykin, Chapter 3.3‐3.4

Page 2: Pulse Modulation

Pulse Modulation

2Pulse modulation (PM) offers two potential advantages over CW modulation

Th t itt d b t t d i t h t b tThe transmitted power can be concentrated into short bursts instead of being generated continuously.  This enables the use of devices which operate better in pulse regime than in CW regime, mostly due to thermal reasons (e.g. semiconductor lasers, microwave active devices)

Time between pulses can be filled by sampled signal form otherTime between pulses can be filled by sampled signal form other sources – a scheme termed time‐division multiplexing.

Analogue PM has a disadvantage of requiring large bandwidth d t b d idthcompared to message bandwidth

Lecture 15COMS3100

Page 3: Pulse Modulation

Pulse Amplitude Modulation (PAM)

3If a message waveform is adequately described by periodic sample values, it can be transmitted using analogue pulse mod lation herein the sample al es mod late themodulation wherein the sample values modulate the amplitude of pulse train.Therefore, the amplitudes of regularly spaced pulses areTherefore, the amplitudes of regularly spaced pulses are varied in proportion to the corresponding sample values of a continuous message signal x(t).This technique is termed Pulse Amplitude Modulation

Lecture 15COMS3100

Page 4: Pulse Modulation

Generation of the PAM signal

4There are two operations involved in the generation of the PAM signal:

1. Instantaneous sampling of the message signal x(t) every Ts seconds, where the sampling rate fs = 1/Ts is chosen in 

d h h l haccordance with the sampling theorem

2. Lengthening the duration of each sample so obtained to t t l ( l d h ld)some constant value τ (sample‐and‐hold)

)(tx)(ts

)(tx

τT

Lecture 15COMS3100

sT

Page 5: Pulse Modulation

Flat‐top Sampling and PAM

5Practical method for obtaining PAM (or implementing the steps 1. and 2.  is the sample‐and‐hold (S/H) technique.  

This method produces flat‐top pulses

sample‐and‐hold circuit

waveform obtainedf

Lecture 15COMS3100

Page 6: Pulse Modulation

Generation of PAM – holding network impulse response

6The finite width pulse obtained by the sample‐and‐holdcircuit can be interpreted mathematically using the following holding network.  

Impulse response of holding network

)(tp

)(⎥⎦⎤

⎢⎣⎡ −

Π=ττ 2/)( ttp

)(tp

)( fP)](arg[ fP )](arg[ fP

Amplitude response of holding network

Phase response ofPhase response of holding network

ττ ffP sinc)( =

Lecture 15COMS3100

Page 7: Pulse Modulation

Flat‐top Sampling and PAM – sampled wave

7Periodic gating of the S/H circuit generates the sampled waveSampling pulse train, p(t)

Signal value at kTS

So far we have not yet specified th “ h ” f th (t) P(f)

Lecture 15COMS3100

the “shape” of the p(t) or P(f)

Page 8: Pulse Modulation

PAM

8Flat‐top sampling is equivalent to passing an ideal sampled wavethrough a network having transfer function P( f ) = [p(t)] Loss of high frequency content is called aperture effectLoss of high frequency content is called aperture effectThe larger the pulse duration or aperture τ, the larger the effectCan be corrected using equalizerNo equalization is needed if t/Ts<<1

Spectrum for ideal  sampling when X( f ) = Π( f/2W )

WW−

aperture effect in flat‐top sampling ττ ffP sinc)( =

WW−⎥⎦⎤

⎢⎣⎡ −

Π=ττ 2/)( ttp

fj

Lecture 15COMS3100

)()()( fXfPfXp δ=fjeftpfP πτττ −== sinc)]([)( F

Page 9: Pulse Modulation

PAM

9

Lecture 15COMS3100

Page 10: Pulse Modulation

PAM

10There are many similarities between PAM and  AM CW modulation

Modulation index

Spectral impulsesSpectral impulses

DC block

PAM spectrum extends from DC up through several harmonics of fsRequired transmission bandwidth can be estimated based on time‐domain considerations

Assuming small pulse duration compared to time between pulsesAssuming small pulse duration compared to time between pulses

Adequate pulse resolution then requires

Lecture 15COMS3100

Page 11: Pulse Modulation

Pulse‐Time Modulation

11The sample values of a message can also modulate the time parameters of a pulse train:

1. Pulse width – pulse‐duration modulation (PDM)

2. Pulse position – pulse‐position modulation (PPM)

The pulse width or pulse position varies in direct proportion to the sample values of x(t)p ( )

Lecture 15COMS3100

Page 12: Pulse Modulation

Pulse‐Duration and Pulse‐Position Modulation

12In both cases a time parameter of the pulse is being modulated

In both cases amplitude remains constant

Methods for producing PDM and PPM are similar

Lecture 15COMS3100

Page 13: Pulse Modulation

Generation of PDM and PPM

13When x(t) exceeds the sawtooth wave  ‐ comparator output is a positive constant AOtherwise comparator output is zero

This is an example of PDM with trailing edgemodulation of the pulsemodulation of the pulse duration

For PPM signal, the PDM signal triggers a monostable pulse generator (triggers on p g ( ggtrailing edge and produces short pulse of fixed duration

Lecture 15COMS3100

Page 14: Pulse Modulation

Generation of PDM and PPM

14Sample values are nonuniformly spaced

This can be tolerated if tk- kTs<<Ts.For nearly uniform sampling the duration of the k‐th pulse in the PDM signal is

where the unmodulated duration τ0 represents x(kTs) = 00  p ( s)PPM pulses have fixed duration and amplitude  ‐> there can be no potential missing pulses. k‐th pulse begins at time

where the unmodulated position kT +t represents x(kT ) = 0 andwhere the unmodulated position kTs+td represents x(kTs) = 0 and the constant t0 controls the displacement of the modulated pulse

Lecture 15COMS3100

Page 15: Pulse Modulation

Generation of PDM

15An approximation for the PDM can be formulated if we assume rectangular pulses centred at t = kTs and assuming tk varies slowly from pulse to pulseslowly from pulse to pulse

where

PDM signal contains the message signal plus a dc component and phase modulated signal at the harmonics of fss

Lecture 15COMS3100

Page 16: Pulse Modulation

PTM to PAM conversion

16Message can be reconstructed by first converting PDD/PPM to PAM.  

Middle waveform is produced by a ramp generator that starts at time kT d t t tkTs and stops at tk

Demodulation requires received pulses with short risetime to preserve accurate message information

Lecture 15COMS3100

preserve accurate message information