prowood project plan adirondack chair/media/files/literature/product literature... · make your...
TRANSCRIPT
Make your outdoors great with other project plans available at www.ProWoodLumber.com Page 1 of 5
ProWood® Project Plan
ADIRONDACK CHAIR
Materials• One 1" x 8" x 8' ProWood®
pressure-treated lumber• Four 1" x 4" x 8' ProWood®
pressure-treated lumber• One 2" x 2" x 8' ProWood®
pressure-treated lumber• One 1" x 3" x 8' ProWood®
pressure-treated lumber• One box of 1-1/4" #6 galvanized
all-purpose screws• One box of 2" #6 galvanized
all-purpose screws• Wood glue
Basic Tools• Circular or table saw• Compund miter saw• Drill and drill bit• Countersink bit• Screwdriver or power drill
with screwdriver bit• Hammer• Tape measure• Leveling tool• Carpenters square• Adjustable triangle scale
With ProWood® Professional Grade pressure-treated lumber, you can easily build a stylish and comfortable outdoor Adirondack chair. And because it’s so affordable, you may want to build a pair. If you wish to add asimple, complementary ottoman or two, see ProWood® Project Plan: Adirondack Ottoman.
Step 1: Cut the Lumber to Size
Caution: Always wear gloves, a dust mask and eye protection when sawing, sanding or machining wood.
Using a circular or table saw on a clean, flat, level surface, cutthe following ProWood® pressure-treated boards for the components of the Adirondack chair.• Stringers: Two 1" x 8" x 32-3/4"• Front apron: One 1" x 8" x 21"• Seat slats: Five 1" x 4" x 21"• Front legs: Two 1" x 4" x 20-3/4"• Arm supports: Two 1" x 3" x 24"• Back slats: Five 1" x 4" x 30-1/2"• Back slats top support: One 1" x 3" x 19-1/2"• Back slats center support: One 2" x 2” x 22-1/2"• Back slats bottom support: One 1" x 4" x 19-1/2"• Arm rests: Two 1" x 4" x 25-1/2"• Front arm supports: Two 1" x 3" x 6"
General Assembly Advice
• Establish a screw pattern to enhance the overall look and feel ofthe final assembled product.
• Predrill all screw holes to ease insertion into the wood andto prevent splitting.
• Countersink all screws so the head of the screw, when placedin the hole, sits flush with—or below—the surface of thesurrounding wood.
Step 2: Cut the Stringers
From the two 1" × 8" x 32-3/4" stringers noted in the cut list,cut the pieces exactly as shown below.Tip: Create a pattern and then copy that pattern for both stringer sides before cutting.• Start by measuring and marking one stringer with a pencil.• Double-check all measurements and angles before cutting so
all cuts are precise and both stringers are cut identically.
37-1/2"
19-1/2"
Make your outdoors great with other project plans available at www.ProWoodLumber.com Page 2 of 5
21-1/2"
21" 30-5/8"
25-1/2"
6-13/16"
32-3/4"
7-1/2"
11/16"2-11/16"
2-3/4"
1-13/16"29-7/8"1"
12-1/2"
2"
5-15/16"
at 15° Angles
15° Angles
Step 3: Attach the Front Apron
Attach the front apron to the stringers using 2" #6 galvanized all-
purpose screws and wood glue. Refer to the illustration below.
• Make sure the front apron is flush with the top and the sides ofthe stringers.
• The bottom of the front apron will be slightly longer than thebottom of the stringers.
• Apply wood glue to the front edge of each stringer.• Screw through the face of the front apron into the front edge of
each stringer.
Step 4: Attach the Seat Slats
Attach the seat slats to the stringers using 1-1/4" #6 galvanized
all-purpose screws and wood glue. Refer to the illustration below.
• Start with the first flat seat slat so it's flush with the stringers’ outer sides and the face of the front apron.
• Apply wood glue to the top edge of the stringers and thefront apron, directly below that first seat slat.
• Screw through the top of that slat.• Following the first flat seat slat process, position, glue and attach
the remaining four slats, one at a time.• Leave a 1/2" gap between each slat.
Make your outdoors great with other project plans available at www.ProWoodLumber.com Page 3 of 5
Step 5: Attach the Front Legs
Attach the two front legs to the stringers using 1-1/4" #6 galvanized all-purpose screws and wood glue. Refer to the illustration below.• Measure and mark 5-1/4" down from the top inside of the
front legs. These marks indicate the height of the first seat slat.• Apply wood glue to the stringer area and to the side edge of the
front apron where the front legs will attach.• Make sure the front legs are flush with the front apron.• Screw the front legs into the stringers.
Step 6: Attach the Arm Supports
Attach the two arm supports to the front legs using 1-1/4" #6 galvanized all-purpose screws and wood glue. Refer to the illustration below.• Measure and mark 3/4" in from the top outside of the front legs
so each arm support will be inset 3/4" in from the outside. • Apply wood glue to the front legs where the arm supports will
be attached.• Place a leveling tool on top of each arm support to check for
level.• Screw the arm supports into the front legs.
5-1/4"
Make your outdoors great with other project plans available at www.ProWoodLumber.com Page 4 of 5
Step 8: Attach the Back
Attach the back to the stringers and horizontal arm supports using 2" #6 galvanized all-purpose screws and wood glue. Refer to the illustration below.• Position the back of the chair so that it's flush with the back of
the seat slats and the top edge of the bottom back support is flush with the top edge of the stringers.
• Screw the stringers to the bottom back support.• Align the top edge of the center back support with the inside
top edge of each horizontal arm support. Make sure thehorizontal arm supports remain level.
• Screw and attach the arm supports to the center back support.
Step 9: Custom Cut the Front Arm Supports
Add a bit of character b custom cutting the front arm supports.
Refer to the illustrations below.
• Using a 1" x 3" x 6" wood piece, measure, mark and cut theface of a front arm support at an angle or an inward arc.
• Mirror that same pattern and repeat the process for the otherfront arm support.
Step 7: Build the Back
The directions that follow will attach the top, center and bottom supports to the back slats. Use 1-1/4" and 2" #6 galvanized all-purpose screws and wood glue. Refer to the illustration below.• Using a flat surface, place the 5 back slats tightly next to each
other with the “good side” facing the surface.• Make sure top and bottom edges are all flush with each other.• Measure and mark 1-1/2" down from the top of the back slats.• Measure and mark 12-3/4" up from the bottom of the slats.• Using a carpenters square to make sure the tops and
bottoms of the slats are flush, separate the back slats withequidistant 1/2" gaps.
Attach the Bottom Back Support• Starting with the two outside back slats, attach the bottom back
support to those slats using 1-1/4" #6 galvanized all-purpose screws and wood glue. Make sure the bottom of the support is flush with the bottom and the sides of the slats.
Attach the Top Back Support• Next, position the top back support so that its top edge is
aligned with the 1-1/2" mark.• Starting with the two outside back slats, attach the top back
support to those slats using 1-1/4" #6 galvanized all-purpose screws and wood glue. Make sure the outside of the support is flush with the sides of the slats.
Attach the Center Back Support• Now position the center back support so that its bottom edge is
aligned with the 12-3/4" mark.• Starting with the two outside back slats, attach the center back
support to those slats using 2" #6 galvanized all-purpose screws and wood glue. Make sure the outside of the support is flush with the sides of the slats.
• Use a carpenters square to make sure the back slats andsupports are all flush and square.
Attach the Back Supports to the Remaining Back Slats• Finish attaching the top, center and bottom back supports to
each of the other back slats, making sure to separate the slats with equidistant 1/2" gaps.
1-1/4"
3" 6"
2-1/2"
3-1/2"
2-1/2"
6"
OR
1-1/2"
12-3/4"
2-1/2"Radius
Make your outdoors great with other project plans available at www.ProWoodLumber.com Page 5 of 5
Step 10: Attach the Front Arm Supports
Attach the custum-cut front arm supports with 1-1/4" #6 galvanized all-purpose screws and wood glue. Refer to the illustration below.• Apply wood glue to the surfaces where the arm supports
will be attached.• Screw and attach each arm support from the inside
of the front legs.
Step 11: Attach the Arm Rests
Attach the arm rests to the horizontal arm supports with 1-1/4" #6 galvanized all-purpose screws and wood glue. Refer to the illustration below.• On the underside of each arm rest, measure and mark 3/8" in
from its back end.• Align that mark with the back end of the horizontal arm
supports.• Make sure the inside edge of each arm rest is flush against
the outside edge of the back slats and the inside edge of the front legs.
• Apply wood glue to the surfaces where the arms rests willbe attached.
• Screw and attach the arm rests to the horizontal and frontarm supports.
ProWood is a registered trademark of Universal Forest Products, Inc., in the U.S. ©2013 Universal Forest Products. All rights reserved.
This document is for illustration purposes only. Use of this product must be in accordance with all local zoning and/or building codes. Consumer assumes all risks and liability associated with the use of this product. For details on safe handling, go to UFPI.com/ptinfo. Warrantor does not provide any warranty, either express or implied, and shall not be liable for any damages, including consequential damages. 7094 Updated 03/15
Make your outdoors great with other project plans available at www.ProWoodLumber.com Page 1 of 3
ProWood® Project Plan
ADIRONDACK OTTOMAN
Materials• One1"x8"x8'ProWood®
pressure-treated lumber• Three1"x4"x8'ProWood®
pressure-treated lumber• OneBoxof1-1/4"#6galvanized
all-purpose screws• OneBoxof2"#6galvanized
all-purpose screws• Woodglue
Basic Tools• Circularortablesaw• Drillanddrillbit• Countersinkbit• Screwdriverorpowerdrill
withscrewdriver bit• Tapemeasure• Carpenterssquare• Adjustabletriangle scale
With ProWood®ProfessionalGradepressure-treatedlumber,youcaneasilybuilda simple yet comfortable outdoor ottoman to complement your Adirondack chair. (SeeProWood®ProjectPlan:AdirondackChair.)
Ifyourwoodprojecttouchestheground,usepressure-treatedlumberthat is rated for ground contact to ensure long-term performance.
Step 1: Cut the Lumber to Size
Caution: Always wear gloves, a dust mask and eye protection when sawing, sanding or machining wood.
Usingacircularortablesawonaclean,flat,levelsurface,cut the following ProWood® pressure-treated boards for the components of the Adirondack ottoman.• Stringers:Two1"x8"x32-3/4"• Frontapron:One1"x8"x21"• Backapron:One1"x2"x21"(ripone1"x4")• Footslats:Eight1"x4"x21"• Frontlegs:Two1"x4"x20-3/4"
General Assembly Advice
• Establishascrewpatterntoenhancetheoveralllookandfeelofthefinalassembledproduct.
• Predrillallscrewholestoeaseinsertionintothewood andto prevent splitting.
• Countersinkallscrewssotheheadofthescrew, when placedinthehole,sitsflushwith—orbelow—thesurface of the surrounding wood.
Step 2: Cut the Stringers
Fromthe two1"×8"x32-3/4"stringersnotedinthecutlist,cutthepiecesexactlyasshownbelow.Tip: Create a pattern and then copy that pattern for both of the stringer sides before cutting.• Startbymeasuringandmarkingonestringerwithapencil.• Double-checkallmeasurementsandanglesbeforecuttingso
all cuts are precise and both stringers are cut the same.
Makeyouroutdoorsgreatwithotherprojectplansavailableatwww.ProWoodLumber.com Page2of3
15-1/2"
21" 30-5/8"
6-13/16"
32-3/4"
7-1/2"
11/16"2-11/16"
2-3/4"
1-13/16"29-7/8"1"
12-1/2"
2"
5-15/16"
at 15° Angles
15° Angles
22-1/2"
FrontView SideView
Step 3: Attach the Front Apron
Attachthefrontaprontothestringersusing2"#6galvanizedall-
purpose screws and wood glue. Refer to the illustration below.
• Makesurethefrontapronisflushwiththetopandthesidesofthe stringers.
• Thebottomofthefrontapronwillbeslightlylongerthanthebottom of the stringers.
• Applywoodgluetothefrontedgeofeachstringer.• Screwthroughthefaceofthefrontapronintothefrontedgeof
each stringer.
Step 4: Attach the Back Apron
Attachthebackaprontothestringersusing2”#6galvanizedall-
purpose screws and wood glue. Refer to the illustration below.
• Makesurethebackapronisflushwiththeinsidebottomandouter edge of each stringer.
• Applywoodgluetotheinsideedgeofeachstringer.• Screwthroughtheoutsidefaceofeachstringerandintothe
back apron.
Make your outdoors great with other project plans available at www.ProWoodLumber.com Page 3 of 3
Step 5: Attach the Foot Slats
Attachthefootslatstothestringersusing1-1/4”#6galvanized
all-purpose screws and wood glue. Refer to the illustration below.
• Startwiththefirstflatfootslatsoit'sflushwiththestringers’outer sides and the face of the front apron.
• Applywoodgluetothetopedgeofthestringersandthefrontapron,directlybelowthatfirstslat.
• Screwthroughthetopofthatslat.• Followingthefirstflatfootslatprocess,position,glueand
attachtheremainingfourslats,oneatatime.• Leavea1/2”gapbetweeneachslat.
Step 6: Attach the Legs
Attachthetwolegstothestringersusing1-1/4"#6galvanizedall-purposescrewsandwoodglue.Refer to the illustration below.• Applywoodgluetothestringerareaandthesideedgeofthe
front apron where the legs will attach.• Makesurethelegsareflushwiththetopofthefirstfoot
slat and the front apron.• Screwthelegsintothestringers.
ProWoodisaregisteredtrademarkofUniversalForestProducts,Inc.,intheU.S.©2015UniversalForestProducts.Allrightsreserved.
Thisdocumentisforillustrationpurposesonly.Useofthisproductmustbeinaccordancewithalllocalzoningand/orbuildingcodes.Consumerassumesallrisksandliabilityassociatedwiththeuseofthisproduct.Fordetailsonsafehandling,gotoUFPI.com/ptinfo.Warrantordoesnotprovideanywarranty,eitherexpressorimplied,andshallnotbeliableforanydamages,includingconsequentialdamages.709403/15