project manual cota administration office renovation€¦ · administration office renovation...

PROJECT MANUAL

COTA ADMINISTRATION OFFICE RENOVATION

FURNITURE, FIXTURES AND EQUIPMENT

PACKAGE

PREPARED FOR:

CENTRAL OHIO TRANSIT AUTHORITY 33 N. HIGH STREET

COLUMBUS, OHIO 43215

PREPARED BY:

ARCHITECTS 300 SPRUCE STREET

COLUMBUS, OHIO 43215 614-461-4664 FAX 614-280-8881

CONTRUCTION DOCUMENTS

MAY 14, 2019

This page intentionally blank

TOC - 1

TABLE OF CONTENTS Cover Sheet Table of Contents VOLUME 1 00 43 25 - Substitution Procedures 00 43 26 - Substitution Request Form DIVISION 01 - GENERAL REQUIREMENTS 01 33 23 Shop Drawings, Product Data, Samples 01 35 13 Special Project Procedures 01 74 00 Cleaning DIVISION 12 – FURNISHINGS 12 56 51 Furniture, Fixtures and Equipment

00 43 25A - 1 SUBSTITUTION PROCEDURES

SECTION 00 43 25A

SUBSTITUTION PROCEDURES 1.01 GENERAL A. This Section applies to substitute products and procedures requested by the Bidder

to be added during the Bid period. . Substitutions included with the Bid that have not been approved under this

Section must be listed on the Substitution Sheet included with the Form of Proposal.

B. Requirements of this Section are in addition to the requirements of Instructions to

Bidders, General Conditions and Supplementary Conditions. C. Requirements of this Section are part of the requirements specified in Section

00 43 25B - Substitution Request Form. 1.02 LIMITATIONS ON SUBSTITUTIONS A. Substitutions will NOT be considered unless Section 00 43 25B - Substitution

Request Form attached in this Project Manual is used and the requirements of this Section and ther Substitution Request Form are fully complied with.

1. Other types of forms are NOT acceptable. B. Substitutions will NOT be considered when requested directly by subcontractor or

supplier. C. Architect will determine the acceptability of all substitutions. 1.03 REQUEST FOR SUBSTITUTIONS A. Bidder's Representation 1. Request for substitution constitutes a representation that the Bidder has

investigated the proposed product and has determined that it is equal to or superior in all respects to the specified product.

2. Request for substitution constitutes a representation that the Bidder will provide same type of warranty for substitution as for specified product.

3. Request for substitution constitutes a representation that the Bidder will coordinate the installation of the accepted substitute, making such changes as may be required for the Work to be complete in all respects.

4. Request for substitution constitutes a representation that the Bidder waives all claims for additional costs related to substitutions which consequently become apparent.


5. Request for substitution constitutes a representation that the cost data is

complete and includes all related cost under his Contract. 6. Request for substitution constitutes a representation that the Bidder has

thoroughly investigated the proposed substitute to determine if license fees and royalties are pending on the proposed substitute.

B. Request for substitutions shall be submitted on Section 00 43 25B - Substitution

Request Form attached in this Project Manual. Legible copies of this form shall be made as required for Bidder's submittals. Each submittal request form shall be complete with data substantiating compliance of proposed substitution with requirements of Contract Documents including the following information:

1. Project title and Architect's project number. 2. Identification of product specified including specification section and

paragraph number. 3. Identification of proposed substitute complete with manufacturer's name

and address, trade name of product, model or catalog number and product data.

4. List of fabricator and supplier (with address and phone number) for proposed substitute.

5. The affect of substitution on dimensions, material thickness, wiring, piping, ductwork, etc. indicated in Contract Documents.

6. The affect of substitution on other trades. 7. The affect of substitution on construction schedule. 8. Differences in quality and performance between specified product and

proposed product. 9. Comparison of manufacturer's guarantees of specified product and

proposed substitute. 10. Availability of maintenance services and replacement materials for

proposed substitute. 11. License fees and/or royalties pending on proposed substitute. 1.04 SUBMITTAL PROCEDURES A. Submit a separate Section 00 43 25B - Substitution Request Form for each

substitution. 1. Form shall be completely and properly filled in. If form is incomplete, the

Architect reserves the right to reject and return form to Bidder for completion and compliance with this section and Form 00 43 25B.

2. Submit to Architect two copies of the completed and signed form. B. Requests for substitutions of products will be considered no later than ten (10)

days prior to Bid Opening Date to allow time for Architect's evaluation of substitutions and the preparation of an addendum, if required.


C. Architect will issue the Addendum to all Bidders to notify them of the Architect's decision to accept the requested substitution.

END OF SECTION

00 43 25B - 1 SUBSTITUTION REQUEST FORM

SECTION 00 43 25B

SUBSTITUTION REQUEST FORM GENERAL: This form is part of the substitution requirements specified in Section 00 43 25A. PROJECT TITLE & NO. TO: MOODY NOLAN INC. 300 Spruce Street, Suite 300 Columbus, Ohio 43215 Telephone (614) 461-4664 FAX (614) 280-8881 Contact and Email: [add contact name and email address] ATTN: SPECIFIED ITEM Section Paragraph PROPOSED SUBSTITUTE Attach complete description, catalog, spec data, and laboratory tests if applicable 1. What effect will substitution have on dimensions, gauges, weights, etc. indicated in

Contract Documents? 2. What effect will substitution have on wiring, piping, ductwork, etc. indicated in Contract

Documents? 3. What effect will substitution have on other trades?


4. What effect will substitution have on construction schedule? 5. What are the differences in quality and performance between proposed substitute and

specified product? 6. What are the differences in all sustainable design characteristics and performance

between proposed substitute and specified product? 7. Manufacturer's guarantees of the specified products and proposed products are: Same: ______ Different (Explain) 8. List (on separate sheet), if applicable, the availability of maintenance services and

replacement materials for proposed substitute. 9. List (on separate sheet) names, addresses and phone numbers of fabricators and

suppliers for proposed substitutes. 10. There [are ] [are no ] license fees and royalties pending on the proposed substitute.

(Explain) 11. The undersigned certifies that this substitution meets all requirements of the Contract

Documents except as specifically noted herein. SUBMITTED TO BIDDER BY: (Supplier/Fabricator) Firm Address Name and Title of Person Signing Signature Telephone No. Date SUBMITTED TO ARCHITECT BY: (Bidder) Firm Address


Name and Title of Person Signing Signature Telephone No. Date FAX No. Email 12. ARCHITECT/ENGINEER'S REVIEW COMMENTS: ___ Tentatively Accepted ___ Rejected due to (pending issuance of incomplete form. Addendum) ___ Not Accepted ___ Received Too Late Signature Date Remarks END OF SECTION

COTA 01 35 13 - 1 Administration Office Renovation SPECIAL PROJECT PROCEDURES

SECTION 01 35 13

SPECIAL PROJECT PROCEDURES PART 1 GENERAL

1.01 SUMMARY

A. The existing building will remain occupied during construction. No interruption of services offered by the Owner is permitted. Consult and carefully schedule with the Owner to achieve this aim.

1.02 PROCEDURES IN OPERATIONAL BUILDING A. Occupancy of Building 1. The existing building will be occupied throughout the entire course of

construction. As such, contractors and their personnel are restricted to construction areas of the building only.

2. Access to areas within the work area of the project which must occur through occupied areas or over occupied areas must be coordinated with the Owner's Representative and the Architect so as to allow spaces to be vacated in time for the work to be accomplished, approximately 48 hours advance notice is required.

a. Where the Owner vacates to allow work in an area, services and utilities may be cut as long as the continuity of that service does not affect other areas. Access must be maintained to all other areas in a safe and sanitary manner.

b. Perform work with cooperation and consideration toward occupants and caution toward existing finishes. Clean-up of work areas in occupied spaces shall be performed at the end of each work day. Debris will not be permitted to accumulate

c. Any work affecting occupants on adjacent floors is to be performed after business hours unless approved in writing by the Owner’s Representative”

3. Operations which are particularly noisy or hazardous to building occupants must be scheduled during weekends or at night. Access to the building will be coordinated with the Owner's Representative and Architect who will generally allow work as required by the construction schedule throughout the normal work day, at night and on weekends as required.

a. The cost of work performed at times other than the "normal" working areas established for the project will be borne by the Contractor(s) involved. No additional payment will be due Contractors whose operations result in "premium" hour work.

B. Conduct: Contractor and workmen under his/her control are to be quiet and non-

offensive. Radios are prohibited.


C. Dress Code 1. Required Apparel: Shirt, long pants, shoes with laces; all suitably clean. 2. Not Permitted: Offensive graphics or messages on clothing, short pants,

tank tops, sandals, open toed shoes, bare torso, bare feet. D. Areas under construction shall be separated from occupied areas by suitable

barriers. See Section 01 50 00 for additional requirements. 1. In no instances may a corridor be blocked nor it's clear width reduced either

to less than 4'-0" or to less than the minimum exit width required in accordance with the Ohio Building Code, whichever is greater.

E. No utilities or services may be interrupted without full consent of and prior

scheduling with the Owner's representative. All functions of existing building must be maintained at all times unless specific written permission is obtained from the Owner. Critical functions include, but are not limited to:

1. Exits 2. Utilities 1.03 NOISE AND SAFETY A. Prohibited Methods: Prohibited methods and materials include, but are not limited

to, the following: 1. Use of explosives. 2. Use of jack hammers or similar equipment which can cause structure-borne

vibration detrimental to the use of the occupied facilities. B. Construction noise limited to Normal Working Hours. 1.04 EXISTING FACILITIES A. Do not use existing telephone, vending machines, cafeteria, or other facilities. 1.05 NO SMOKING POLICY A. Smoking inside buildings is not permitted. 1.06 SITE AND BUILDING ACCESS A. Existing driveways and entrances which serve the premises must be maintained.

They must be available to the Owner and public at all times. Do not use these areas for parking or storage of materials.

1. Do not unreasonably encumber the site with materials or equipment.

Confine stock piling of materials and location of storage trailers to the areas


indicated on the drawings or as directed by the Architect. 2. Architect will administer available space equitably among other prime

contractors. 3. Schedule deliveries so as to minimize space and time requirements for

storage of materials and equipment on the site.

END OF SECTION

COTA 01 74 00 - 1 Administration Office Renovation CLEANING

SECTION 01 74 00

CLEANING PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. Execute cleaning, during progress of the work and at completion of the work, as

required by Contract Documents. 1.02 RELATED SECTIONS A. Cutting and Patching: Section 01 73 29. B. Cleaning for Specific Products or Work: Specification section for the work. 1.03 CLEANING AND DISPOSAL REQUIREMENTS A. Standards: Maintain project in accord with the following safety and insurance

standards: 1. Applicable Federal and State Requirements. 2. National Fire Protection Association. B. Conduct cleaning and disposal operations to comply with local ordinances and anti-

pollution laws. 1. Do not burn or bury rubbish and waste materials on project site. 2. Do not dispose of volatile wastes such as mineral spirits, oil or paint thinner

in storm or sanitary sewers. 3. Do not dispose of waste into streams or waterways. 4. Wet down dry materials and rubbish to prevent dust. PART 2 PRODUCTS 2.01 MATERIALS A. Select and use cleaning materials and equipment with care to avoid scratching,

marring, defacing, staining or discoloring surfaces cleaned. B. Use only cleaning materials recommended by manufacturer of surfaces to be

cleaned.

1. Use cleaning products that meet Green Seal GS-37, or if GS-37 is not applicable, use products that comply with the California Code of Regulations maximum allowable VOC levels.

COTA 01 74 00 - 2 Administration Office Renovation CLEANING

C. Use cleaning materials only on surfaces recommended by the cleaning material

manufacturer. PART 3 EXECUTION 3.01 FINAL CLEANING

A. General: Provide final cleaning. Conduct cleaning and waste-removal operations to comply with local laws and ordinances and Federal and local environmental and antipollution regulations.

1. Leave Project clean and ready for occupancy. B. Employ experienced workmen, or professional cleaners for final cleaning. C. At the completion of the work, remove all surplus material, false work, temporary

structures, including foundations thereof, plants of any description and debris of every nature resulting from their operations and put the site in a neat and orderly condition.

D. Clean exposed interior hard-surfaced finishes to a dirt-free condition, free of

stains, films, and similar foreign substances. Restore reflective surfaces to their original condition.

E. Clean transparent materials, including mirrors and glass in doors and windows.

Remove glazing compounds and other noticeable, vision obscuring materials. Replace chipped or broken glass and other damaged transparent materials. Polish mirrors and glass, taking care not to scratch surfaces.

F. Remove grease, dust, dirt, stains, labels, fingerprints and other foreign materials

from sight-exposed interior and exterior surfaces, including light fixtures and lenses; polish surfaces so designated to a shine finish.

1. Clean finishes free of dust, stains, films and other foreign substances. 2. Clean transparent and glossy materials to a polished condition; remove

foreign substances. Polish reflective surfaces to a clear shine. G. Remove temporary protection and labels not required to remain H. Repair, patch and touch-up marred surfaces to specified finish, to match adjacent

surfaces.

END OF SECTION

12 56 51- 1 COTA FURNITURE, FURNISHINGS Administration Office Renovation AND ACCESSORIES

SECTION 12 56 51

FURNITURE, FURNISHINGS AND ACCESSORIES PART 1 GENERAL 1.01 WORK INCLUDED A. Provide all labor, materials and transportation necessary for the complete

installation of all furniture, furnishings and accessories indicated on the drawings or specified herein or both.

1.02 SUBMITTALS A. Shop Drawings: For each item, submit manufacturer's product data in accordance

with the General Conditions. B. Samples: Submit color chips and fabric samples for Architect's color verification or

selection. C. Maintenance Instructions: Submit three copies of manufacturer's recommended

maintenance instructions, including information needed for removal of common stains.

1.03 DELIVERY AND INSTALLATION A. Protect furniture and accessories during delivery, storage and handling to prevent

damage, soiling and deterioration. B. Shipment of furniture and accessory items may be made directly to building site in

cases where prior approval of Architect has been obtained and the building is ready for furniture installation. Furniture Contractor is responsible for knowing when his merchandise is to arrive and must have available all labor and equipment for unloading and handling.

C. Delivery must be in accordance with the Progress Schedule developed by this

Contractor in cooperation with the other Contractors and Owner as provided for under Article 4 of the General Conditions.

D. Contractor is responsible for temporary storage of all furniture and accessory items

until time for delivery and installation. E. Particular care must be taken by furniture Contractor when handling equipment and

furniture during installation so as not to damage existing building, carpet and shelving.

12 56 51- 2 COTA FURNITURE, FURNISHINGS Administration Office Renovation AND ACCESSORIES

1.04 DAMAGED ITEMS A. Furniture Contractor is responsible for all damage to items provided under this

contract up to the time of acceptance by the Owner, whether this damage results during shipment from manufacturer, delivery to site, placement, or through carelessness or malicious mischief or whatever reason, and final payment will be made only for undamaged items. Contractor shall replace all damaged items or parts of assembled or manufactured items as soon as discovered.

B. Nominal touch-up or repair of painted finishes will be permitted if done in

accordance with the manufacturer's recommended procedures for such repair and the end results, in the opinion of the Architect, appears as good as new. Repairs must return item to original appearance and function.

PART 2 PRODUCTS 2.01 FURNITURE, FURNISHINGS AND ACCESSORIES A. See following documents. PART 3 EXECUTION 3.01 GENERAL REQUIREMENTS A. Placement shall be made in accordance with the locations indicated on the

drawings. When conditions require adjustment of placement, the Architect will determine or approve alternate placement.

B. Placement and installations shall be performed by mechanics skilled in the

requirements of that type of work. C. Upon completion of the work, all furniture and accessories shall be fully assembled

with moveable parts operating properly. D. Installation shall be in accordance with the requirements, standards and

procedures of the product manufacturer.

END OF SECTION

Project Name: COTA Downtown Admin. Office Reno.

Designer: D. Miller

Ship‐To Address: 33 North High Street

Columbus, OH 43215

Project Number: 18088.03

Issue Date: 5/13/2019

Revised Date:

Plan Code: B1

Item Type: Single Sound BoothDimensions: 47" W x 47" D x 88" H

Style/Series: FreeZonez ‐ Privacy for One

Model #: FreeZonez Secret ‐ 4'x4'

Manufacturer: ZONEZ

Rep Group:

Contact Name: BLG / Barry Longhino

Phone #: 614.378.6523

email Address: [email protected]

Description: Zonez FreeZonez Secret 4x4 Privacy/Phone Booth. "Secret" STC42 Booth (Class A) features Architectural Aluminum on the exterior walls, 9mm PET on the interior walls, and door construction of air channel between 1/4" laminated glass and 1/4" tempered glass. Includes ChargeSpot, automatic door closer with internal and external handles, duplex outlets and dual USB charge plugs. Doors mounted using continuous hinge. Sensor‐activated LED overhead lights and air exchange. Air exchange system office laminar air flow. Right door swing.

Finish 1: Interior: Light Grey PET‐P91

Manufacturer:

Finish 2: Frame: Extruded Aluminum

Pattern:

Color:Yardage/Sq. Ft.:

Finishes

YesShop Drawings:

YesFinish Submittal:Finish 3: Exterior: C02 White Architectural Aluminum

Fabric / Upholstery

Rooms: 710(2)

Address:

City / State: ,

Zip:

Phone #: 800.929.7702

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 2

Page 1B1 ZONEZ Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

B1Item: Single Sound Booth

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: B2

Item Type: Double Sound BoothDimensions: 72" W x 72" D x 88" H

Style/Series: FreeZonez ‐ Inclusive Privacy

Model #: FreeZonez Secret ‐ 6'x6'

Manufacturer: ZONEZ

Rep Group:

Contact Name: BLG / Barry Longhino

Phone #: 614.378.6523


Description: Zonez FreeZonez Inclusive Privacy Secret 6x6 ADA Privacy/Phone Booth. "Secret" STC42 Booth (Class A) features Architectural Aluminum on the exterior walls, 9mm PET on the interior walls, and door construction of air channel between 1/4" laminated glass and 1/4" tempered glass. Includes ChargeSpot, automatic door closer with internal and external handles, duplex outlets and dual USB charge plugs. Doors mounted using continuous hinge. Sensor‐activated LED overhead lights and air exchange. Air exchange system office laminar air flow. Right door swing.

Finish 1: Interior: Light Grey PET‐P91

Manufacturer:

Finish 2: Frame: Extruded Aluminum

Pattern:


Finishes

YesShop Drawings:

YesFinish Submittal:Finish 3: Exterior: C02 White Architectural Aluminum

Fabric / Upholstery

Rooms: 710(1)

Address:

City / State: ,

Zip:

Phone #: 800.929.7702

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 1



Designer: D. Miller


Columbus, OH 43215



Revised Date:

B2Item: Double Sound Booth

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: C1

Item Type: Task ChairDimensions: 25‐1/8" W x 15" D x 37‐1/8" H 15‐1/2" ‐ 20" SH

Style/Series: Setu ‐ Multipurpose Task Chair

Model #: CQ5 1 M A 98 L7 HCC NNN

Manufacturer: Herman Miller Inc.

Rep Group:

Contact Name: Leslie Collett Felix

Phone #: 614‐262‐5010


Description: Herman Miller Setu Series Multipurpose Task Chair with Ribbon Arms. 25‐1/8" W x 15" D x 37‐1/8" H 15‐1/2" ‐ 20" SH. 5‐Star Base ‐ Pneumatic, Standard‐height Range. Lyris 2 Suspension Seat and Back. 98 Studio White Frame Finish with L7 Silver Alloy Base. 2‐1/2" Caster, Black Yoke, Medium Roll Resistance, Hard Floors and Carpet.

Finish 1: Frame: 98 Studio White

Manufacturer:

Finish 2: Base: L7 Silver Alloy

Pattern:


Finishes

YesShop Drawings:

YesFinish Submittal:Finish 3: Lyris 2: Java 4W30

Fabric / Upholstery

Rooms: 709(16)

Address: 855 East Main Ave. PO Box 302

City / State: Zeeland, MI

Zip: 49464‐0302

Phone #: 1.800.851.1196

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 16

Page 5C1 Herman Miller Inc. Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

C1Item: Task Chair

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: C2

Item Type: Side Chair w/ 4‐Star BaseDimensions: 25‐1/8" W x 15" D x 36" H 18‐1/2" SH

Style/Series: Setu ‐ Multipurpose Fixed Height Chair

Model #: CQ5 4 M A 98 L7 X8 NNN


Rep Group:


Phone #: 614‐262‐5010


Description: Herman Miller Setu Series Multipurpose Fixed Side Chair with Ribbon Arms. 25‐1/8" W x 15" D x 36" H 18‐1/2" SH. 4‐Star Base ‐ Swivel Seat, Fixed Height. Lyris 2 Suspension Seat and Back. 98 Studio White Frame Finish with L7 Silver Alloy Base. Glide, Low Profile, Hard Floors or Carpet.

Finish 1: Frame: 98 Studio White

Manufacturer:


Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 707(4), 713(2)



Zip: 49464‐0302

Phone #: 1.800.851.1196

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 6



Designer: D. Miller


Columbus, OH 43215



Revised Date:

C2Item: Side Chair w/ 4‐Star Base

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: C3

Item Type: Task StoolDimensions: 25‐1/8" W x 15" D x 43‐3/8"‐51‐1/4" H 26‐3/8"‐34‐1

Style/Series: Setu ‐ Multipurpose Task Stool

Model #: CQ7 9 M A 98 98 L7 OC NNN


Rep Group:


Phone #: 614‐262‐5010


Description: Herman Miller Setu Series Multipurpose Task Stool with Ribbon Arms. 25‐1/8" W x 15" D x 43‐3/8" ‐ 51‐1/4" H 26‐3/8" x 34‐1/4" SH. 5‐Star Base ‐ Pneumatic, Stool‐height Range. Lyris 2 Suspension Seat and Back. 98 Studio White Frame Finish with L7 Silver Alloy Base. 2‐1/2" Caster, Medium Roll Resistance, Black Yoke, Hard Floors and Carpet w/ Quiet Rool Technology.

Finish 1: Frame/Column: 98 Studio White

Manufacturer:


Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 710(24), 713(2)



Zip: 49464‐0302

Phone #: 1.800.851.1196

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 26



Designer: D. Miller


Columbus, OH 43215



Revised Date:

C3Item: Task Stool

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: C4

Item Type: Lounge ChairDimensions: 34‐1/4" D x 35" W x 41‐1/4" H 17" SH

Style/Series: Bob Lounge Chair with Headrest

Model #: 221

Manufacturer: Coalesse

Rep Group:

Contact Name: Stephen Stefancin

Phone #: 317.340.3765


Description: Coalesse Bob Lounge Chair w/ Headrest. Vinyl Upholstery. Aluminum Matte Polished Base. 34‐1/4" D x 35" W x 41‐1/4" H 17" SH. Vinyl: Grade 6 Brisa.

Finish 1: Vinyl: Grade 6 Brisa

Manufacturer:

Finish 2: Base: 8040 Aluminum Matte Polished

Pattern:


Finishes

YesShop Drawings:

YesFinish Submittal:Finish 3:

Fabric / Upholstery

Rooms: 711(4)

Address:

City / State: ,

Zip:

Phone #: 866.645.6952

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 4

Page 11C4 Coalesse Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

C4Item: Lounge Chair

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: C5

Item Type: StoolDimensions: 17" D x 17‐1/4" W x 31‐1/2" H 29‐3/4" SH

Style/Series: Last Minute

Model #: COLMS30

Manufacturer: Coalesse

Rep Group:

Contact Name: Stephen Stefancin

Phone #: 317.340.3765


Description: Coalesse Last Minute Stool. Vinyl Upholstery. Polished Trivalent Chrome Base. 17" D x 17‐1/4" W x 31‐1/2" H 29‐3/4" SH. Vinyl: Grade 6 Brisa.

Finish 1: Vinyl: Grade 6 Brisa

Manufacturer:

Finish 2: Frame: 9207 Polished Trivalent Chrome

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 214(4), 710(4), 711(8)

Address:

City / State: ,

Zip:

Phone #: 866.645.6952

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 16



Designer: D. Miller


Columbus, OH 43215



Revised Date:

C5Item: Stool

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: C6

Item Type: Task ChairDimensions: 30" W x 18‐1/2" D x 42‐3/4" Max H 16"‐20‐1/2" SH

Style/Series: Mirra 2 Work Chair

Model #: MFR1 2 3 A W A A AJ G1 BB G1 IA703 BK


Rep Group:


Phone #: 614‐262‐5010


Description: Herman Miller Mirra 2 Work Chair w/ Arms. 30" W x 18‐1/2" D x 42‐3/4" Max H 16"‐20‐1/2" SH. Standard Height Range. Tilt Limiter and Seat Angle. Adjustable Arms FlexFront Adjustable Seat Depth. Butterfly Suspension Back. Adjustable Lumbar Support. Graphite Base/Frame/Back Finish. 2‐1/2" Hard Caster, Black Yoke, Carpet Only. Graphite AireWeave.

Finish 1: Base/Frame/Back: G1 Graphite

Manufacturer:

Finish 2: Armpad: BK Black

Pattern:


Finishes

YesShop Drawings:

YesFinish Submittal:Finish 3: AireWeave: 1A703 Graphite

Fabric / Upholstery

Rooms: 101B(3), 101C(4)



Zip: 49464‐0302

Phone #: 1.800.851.1196

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 7



Designer: D. Miller


Columbus, OH 43215



Revised Date:

C6Item: Task Chair

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: CR1

Item Type: Credenza Storage UnitDimensions: 72" W x 18" D x 22.25" H

Style/Series: Aptos

Model #: 34‐L7218FSL3

Manufacturer: OFS

Rep Group:

Contact Name: Cheryl Davis

Phone #: 614.485.9427


Description: OFS Aptos Series Low Credenza. 72" W x 18" D x 22.25" H. 36" W Open w/ One Adjustable Shelf (Right) and One Box/Lateral File (Left). Single 0.75" Thick Top and Finished Back Panel. Standard Veneer: TBD.

Finish 1: Veneer: Standard

Manufacturer:

Finish 2:

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 711(1)

Address: PO Box 100 1204 East 6th St.

City / State: Huntingburg, IN

Zip: 47542

Phone #: 800.521.5381

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 1

Page 17CR1 OFS Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

CR1Item: Credenza Storage Unit

Catalogue Image

Page 18CR1 OFS Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: L1

Item Type: Locker UnitDimensions: 15" W x 15" D x 64" (75" TW)

Style/Series: Day Use Locker ‐ 2‐Tier

Model #: (1) DU1 and (1) DU2

Manufacturer: Spacesaver Corporation

Rep Group: Patterson Pope

Contact Name:

Phone #:

email Address:

Description: Spacesaver 2‐Tier Day Use Locker. 15" W x 15" D x 64" H ‐ 75" Total Width. (2) 29‐3/4" H. Single Hook on Back Panel. Digilock Numeris Aspire Keypad. Number Tag on each door. 4" Recessed Base.

Finish 1: Metal: Cottonwood

Manufacturer:

Finish 2: PLam: Wilsonart Shadow Zephyr 4857‐60

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 707(1)

Address: 1450 Janesville Ave.

City / State: Fort Atkinson, WI

Zip: 53538

Phone #: 1.800.255.8170

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 1

Page 19L1 Spacesaver Corporation Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

L1Item: Locker Unit

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: L2

Item Type: Locker UnitDimensions: 15" W x 15" D x 64" (75" TW)

Style/Series: Day Use Locker ‐ 3‐Tier

Model #: (1) DU1 and (1) DU2

Manufacturer: Spacesaver Corporation

Rep Group: Patterson Pope

Contact Name:

Phone #:

email Address:

Description: Spacesaver 3‐Tier Day Use Locker. 15" W x 15" D x 64" H ‐ 75" Total Width. (3) 19‐3/4" H Units. Single Hook on Back Panel. Digilock Numeris Aspire Keypad. Number Tag on each door. 4" Recessed Base.

Finish 1: Metal: Cottonwood

Manufacturer:

Finish 2: PLam: Wilsonart Shadow Zephyr 4857‐60

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 707(1)

Address: 1450 Janesville Ave.

City / State: Fort Atkinson, WI

Zip: 53538

Phone #: 1.800.255.8170

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 1



Designer: D. Miller


Columbus, OH 43215



Revised Date:

L2Item: Locker Unit

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: MB1

Item Type: Mobile Marker BoardDimensions: 47‐1/2" W x 30‐1/4" D x 76‐1/2" H

Style/Series: Exclave ‐ Large

Model #: EXLC. MW L BK 8Q 91


Rep Group:


Phone #: 614‐262‐5010


Description: Herman Miller Exclave Large Mobile Cart Magnetic Whiteboard. 47‐1/2" W x 30‐1/4" D x 76‐1/2" H. White Base, Folkstone Grey Cart Side Finish, Black Pull Handle. INCLUDE (1) EXMK EXCLAVE MARKER & ERASER KIT PER UNIT.

Finish 1: Base ‐ 91 White

Manufacturer:

Finish 2: Cart Side ‐ 8Q Folkstone Grey

Pattern:


Finishes

YesShop Drawings:

YesFinish Submittal:Finish 3: Handle ‐ Black

Fabric / Upholstery

Rooms: 710(3)



Zip: 49464‐0302

Phone #: 1.800.851.1196

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 3

Page 23MB1 Herman Miller Inc. Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

MB1Item: Mobile Marker Board

Catalogue Image

Page 24MB1 Herman Miller Inc. Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: S1

Item Type: Single Seat LoungeDimensions: 22.5" W x 28" D x 35.75" H 18" SH

Style/Series: Coact

Model #: F78041‐M BLK H4N A2J X9 X9 X9 C4 w/ Power

Manufacturer: OFS

Rep Group:


Phone #: 614.485.9427


Description: OFS Coast Series Mid Back Lounge Chair without Arms. With Power. Round Post Legs in Polished Chrome. Ganging. 22.5" W x 28" D x 35.75" H 18" SH. Vinyl: Grade 4.

Finish 1: Vinyl: Grade 4

Manufacturer:

Finish 2: Power: BLK Black

Pattern:


Finishes

YesShop Drawings:

YesFinish Submittal:Finish 3: Leg: A2J Polished Chrome

Fabric / Upholstery

Rooms: 101A(1)



Zip: 47542

Phone #: 800.521.5381

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 1

Page 25S1 OFS Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

S1Item: Single Seat Lounge

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: S2

Item Type: Curve LoungeDimensions: 43" W x 43" D x 35.75" H 18" SH

Style/Series: Coact

Model #: F78045‐M N7 BLK H4N A2J X9 X9 X9 C4 w/ Power

Manufacturer: OFS

Rep Group:


Phone #: 614.485.9427


Description: OFS Coast Series Corner Unit without Arms. With Power (Top Shelf). Round Post Legs in Polished Chrome. Ganging. 43" W x 43" D x 35.75" H 18" SH. Vinyl: Grade 4.


Manufacturer:

Finish 2: Power: BLK Black PLam: TBD

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 101A(1)



Zip: 47542

Phone #: 800.521.5381

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 1



Designer: D. Miller


Columbus, OH 43215



Revised Date:

S2Item: Curve Lounge

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: S3

Item Type: 3‐Seat LoungeDimensions: 67.5" W x 28" D x 35.75" H 18" SH

Style/Series: Coact

Model #: F78043‐M C6T/BLK H4N A2J X9 X9 X9 C4 w/ Power

Manufacturer: OFS

Rep Group:


Phone #: 614.485.9427


Description: OFS Coast Series Mid Back Sofa (3 Seat) without Arms. With Power (Right Facing). Round Post Legs in Polished Chrome. Ganging. 67.5" W x 28" D x 35.75" H 18" SH. Vinyl: Grade 4.


Manufacturer:

Finish 2: Power: BLK Black

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 101A(1)



Zip: 47542

Phone #: 800.521.5381

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 1



Designer: D. Miller


Columbus, OH 43215



Revised Date:

S3Item: 3‐Seat Lounge

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: S4

Item Type: Lounge Chair w/ ScreenDimensions: 40" W x 29" D x 57" H 17" SH

Style/Series: Peek & Boo

Model #: PEK/1

Manufacturer: Boss Design

Rep Group: Seibold Baker

Contact Name: Brent Weirtz

Phone #:


Description: Boss Design Peek & Boo Lounge Chair with Upholstered Screen. 40" W x 29" D x 57" H 17" SH. Swivel Base. Fixed Lumbar Cushion. Twin Stitch Detail. Seat: Grade 3. Screen: Grade 3.

Finish 1: Seat: Grade 3

Manufacturer:

Finish 2: Screen: Grade 3

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 214(2)

Address: 2014 Chestnut Street

City / State: High Point, NC

Zip: 27262

Phone #: 1.844.353.7834

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 2

Page 31S4 Boss Design Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

S4Item: Lounge Chair w/ Screen

Catalogue Image

Page 32S4 Boss Design Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: T1

Item Type: Flip‐Top Conference TableDimensions: 30" D x 60" W x 28‐1/2" H

Style/Series: Everywhere

Model #: DT5A S 20 60 L T 20


Rep Group:


Phone #: 614‐262‐5010


Description: Herman Miller Everywhere Flip‐Top Rectangular Table. 30" D x 60" W x 28‐1/2" H. Square Edged. Laminate Top, Thermoplastic Edge. On Glides. All Standard Finishes. Colors: TBD.

Finish 1: All Standard: TBD

Manufacturer:

Finish 2:

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 709(4)



Zip: 49464‐0302

Phone #: 1.800.851.1196

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 4

Page 33T1 Herman Miller Inc. Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

T1Item: Flip‐Top Conference Table

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: T2

Item Type: Height Adjustable 45 Degree Work TableDimensions: 30" D X 48" W x 27" x 46" Hgt. Adj.

Style/Series: Renew ‐ 120 Degree

Model #: DU6GC S 30 E SRM PHD NNN 57


Rep Group:


Phone #: 614‐262‐5010


Description: Herman Miller Renew Sit‐to‐Stand 120 Corner Table w/ C‐Foot. 30" D x 48" W x 27" x 46" Hgt. Adj. Square Edged. Laminate Top, Thermoplastic Edge. Electric Standard Range. Digitial Read Out with Memory Switch. High Density Cable Trough. On Glides. All Standard Finishes. Colors: TBD. **INCLUDE** (2) 42" H x 48" W Flat Edge, Surface Attached Screen to 48" Side of Corner Table. Fabric: Price Category 1. Color: TBD.


Manufacturer:

Finish 2:

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 710(12)



Zip: 49464‐0302

Phone #: 1.800.851.1196

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 12



Designer: D. Miller


Columbus, OH 43215



Revised Date:

T2Item: Height Adjustable 45 Degree Work Table

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: T3

Item Type: Height Adjustable TableDimensions: 30" D x 72" W x 27" x 46" Hgt. Adj.

Style/Series: Renew

Model #: DU6AC S 30 72 L E PHD NNN 57


Rep Group:


Phone #: 614‐262‐5010


Description: Herman Miller Renew Sit‐to‐Stand w/ C‐Foot. 30" D x 72" W x 27" x 46" Hgt. Adj. Square Edged. Laminate Top, Thermoplastic Edge. Electric Standard Range. Digitial Read Out with Memory Switch. High Density Cable Trough. On Glides. All Standard Finishes. Colors: TBD.


Manufacturer:

Finish 2:

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 710(6), 713(2)



Zip: 49464‐0302

Phone #: 1.800.851.1196

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 8



Designer: D. Miller


Columbus, OH 43215



Revised Date:

T3Item: Height Adjustable Table

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: T4

Item Type: Harvest / Collaboration TableDimensions: 48" D x 96" W x 42" H

Style/Series: Gather ‐ Harvest ‐ Metal Powered

Model #: S943 TST4896 X XX LAM TBD P1 P27 5913P12CM

Manufacturer: Allsteel

Rep Group:

Contact Name: Matthew Stafford, Mkt. Dev. Mgr.

Phone #:


Description: Allsteel Gather Harvest Metal Base Table with PLam Top. 48" D x 96" W x 42" H. PLam: TBD. Metal: P27 Black. 12' Corded Surface Mounted Power w/ 2 Receptacles, 1 Data.

Finish 1: PLam: TBD

Manufacturer:

Finish 2: Metal: P27 Black

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 711(1)

Address: 2210 Second Ave

City / State: Muscatine, IA

Zip: 52761

Phone #: 1‐888‐255‐7833

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 1

Page 39T4 Allsteel Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

T4Item: Harvest / Collaboration Table

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: T5

Item Type: Coffee TableDimensions: 36" Dia. x 17" H

Style/Series: Spun

Model #: E1M X9 TBD TBD

Manufacturer: OFS

Rep Group:


Phone #: 614.485.9427


Description: OFS Spun Round Cocktail Table. 36" Dia. x 17" H. PLam Top: TBD. Base: Stainless Steel.

Finish 1: Base: Stainless Steel

Manufacturer:

Finish 2: PLam: TBD

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 711(1)



Zip: 47542

Phone #: 800.521.5381

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 1

Page 41T5 OFS Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

T5Item: Coffee Table

Catalogue Image

Page 42T5 OFS Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: T6

Item Type: 36" Dia. TableDimensions: 36" Dia.

Style/Series: Everywhere

Model #: DT1C S 36 L P 57


Rep Group:


Phone #: 614‐262‐5010


Description: Herman Miller Everywhere Round Top Table. 36" D x 28‐1/2" H. Square Edged. Laminate Top, Thermoplastic Edge. On Glides. All Standard Finishes. Colors: TBD.


Manufacturer:

Finish 2:

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 707(2)



Zip: 49464‐0302

Phone #: 1.800.851.1196

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 2



Designer: D. Miller


Columbus, OH 43215



Revised Date:

T6Item: 36" Dia. Table

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: T7

Item Type: Harvest / Collaboration TableDimensions: 42" D x 72" W x 42" H

Style/Series: Gather ‐ Harvest ‐ Metal Powered

Model #: S943 TST4272 X XX LAM TBD P1 P27 5913P12CM

Manufacturer: Allsteel

Rep Group:

Contact Name: Matthew Stafford, Mkt. Dev. Mgr.

Phone #:


Description: Allsteel Gather Harvest Metal Base Table with PLam Top. 42" D x 72" W x 42" H. PLam: TBD. Metal: P27 Black. 12' Corded Surface Mounted Power w/ 2 Receptacles, 1 Data.

Finish 1: PLam: TBD

Manufacturer:

Finish 2: Metal: P27 Black

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 214(1)

Address: 2210 Second Ave

City / State: Muscatine, IA

Zip: 52761

Phone #: 1‐888‐255‐7833

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 1



Designer: D. Miller


Columbus, OH 43215



Revised Date:

T7Item: Harvest / Collaboration Table

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: T8

Item Type: Pull‐Up Work TableDimensions: 16‐1/2" W x 15‐3/4" D x 25" ‐ 42‐3/4" H

Style/Series: Flamingo

Model #: FLT/P/L/HA

Manufacturer: Boss Design

Rep Group: Seibold Baker

Contact Name: Brent Weirtz

Phone #:


Description: Boss Design Flamingo Table with Adjustable Height. 16‐1/2" W x 15‐3/4" D x 25" ‐ 42‐3/4" H. Chrome Finish with PLam Writing Surface.

Finish 1: Metal: Polished Chrome

Manufacturer:

Finish 2: PLam: TBD

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 214(2)

Address: 2014 Chestnut Street

City / State: High Point, NC

Zip: 27262

Phone #: 1.844.353.7834

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 2

Page 47T8 Boss Design Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

T8Item: Pull‐Up Work Table

Catalogue Image

Page 48T8 Boss Design Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: TR1

Item Type: Trash Receptable ‐ SmallDimensions: 10.5" D x 14.5" W x 15.25" H

Style/Series: Indoor Trash Can w/o Lid

Model #: FG254300BLA

Manufacturer: Rubbermaid

Rep Group:

Contact Name:

Phone #:

email Address:

Description: Rubbermaid Indoor Trash Can w/ no lid. Black Polyester. 10.5" D x 14.5" W x 15.25" H.

Finish 1: Black Polyester

Manufacturer:

Finish 2:

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 101B(3), 101C(4), 713(2)

Address: 3124 Valley Avenue

City / State: Winchester, VA

Zip: 22601

Phone #: 540.667.8700

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 9

Page 49TR1 Rubbermaid Compiled: 05‐13‐2019


Designer: D. Miller


Columbus, OH 43215



Revised Date:

TR1Item: Trash Receptable ‐ Small

Catalogue Image



Designer: D. Miller


Columbus, OH 43215



Revised Date:

Plan Code: TR2

Item Type: Trash Receptacle ‐ LargeDimensions: 18" W x 9" D x 32" H

Style/Series: Metallic Half Round

Model #: FGSO12SSSPL

Manufacturer: Rubbermaid

Rep Group:

Contact Name:

Phone #:

email Address:

Description: Rubbermaid Metallic Half Round Open Top Satin Stainless Steel Waste Receptacle with Rigid 12 Gallon Plastic Liner. Made of heavy‐gauge, fire‐safe steel. Sanitary hands‐free operation. Includes a leak‐proof plastic liner.

Finish 1: Stainless Steel

Manufacturer:

Finish 2:

Pattern:


Finishes

YesShop Drawings:


Fabric / Upholstery

Rooms: 101(2), 101C(1), 118A(1), 214(1), 707(1), 709(1), 710(2), 711(3)

Address: 3124 Valley Avenue

City / State: Winchester, VA

Zip: 22601

Phone #: 540.667.8700

YesCOM Submittal:

Alternate 1:

Alternate 2:

Total Quantity: 12



Designer: D. Miller


Columbus, OH 43215



Revised Date:

TR2Item: Trash Receptacle ‐ Large

Catalogue Image


F.E.C.

1 2 3 4 5 6 7 8 9 10 11

A

B

C

MEN'S719

WOMEN'S716

JAN717

MECH718

STORAGE706

ELEC715

STORAGE714

OFFICES713

STAIR#2

ELEV#3

ELEV#2

STAIR#1

MECH708

LOCKABLE STORAGE707

CONFERENCE709

OPEN OFFICE710

KITCHENETTE711

ELEV#1

C1C1C1C1C1

C1C1C1C1C1C1

C1

C3C3

C2C2

C3C3

C3C3

C3C3 C3 C3 C3 C3

C3

C3

C3

C3

C3C3 C3

T2C3

T2 C3C3

T2C3

C3

C4 C4

C4C4

C5C5C5C5

C5C5C5C5

T1 T1

T1T1T2

T2

T2T2T2

T2T2T2 T2

T3T3

T3

T3 T3

T3 T3T4T5CR1

MB1

MB1C2

C2

C2 C2

T6

T6B2 B1 MB1

UP

DN

UP

DN

C3C3T3 C1

C1C1C1

C5

C5C5C5 C5

SUITE LOBBY703A

CORRIDOR703

TR2TR2

TR1 TR1

TR2

TR2

TR2

TR2TR2

B1B1

5'-3"

L1

Generic - 12"

L2

Generic - 12"

9 10 11 12 13

A

B

C

12.7

FIRE CMD CTR119

ELEV.#2

ELEV.#1

STAIR#1

C6C6C6

C6

C6

C6

S1S2 S3

LOBBY101

VESTIBULE100

BUSINESS WAITING101A

CORRIDOR118AELEV LOBBY

118

CORRIDOR111

RETAIL/SALES101C

RECEPTION/ SECURITY101B

UPDN

C6

TR1TR1

TR1TR2

TR1

TR1

TR1

TR1

TR2

TR2

TR2

9 10 11 12 13

A

B

C

12.7

OPEN TO BELOWOPEN TO BELOW OPEN TO BELOW

ELEV#1

ELEV#2

LIBRARY214

OFFICE201

MECH214A

CORRIDOR213

STAIR#1

DN

UP

C5C5

C5C5

T7

TR2

S4

S4

T8

T8

PLAN LEGEND

NO WORK IN THIS AREA

WORK TO BE PROPOSED AS AN ALTERNATE

FF&E GENERAL NOTES

A. FURNITURE SHOWN IN THESE PLANS ARE FOR REFERENCE ONLY. B. CONTRACTOR IS TO COODINATE INSTALLATION OF FURNITURE WITH

FURNITURE VENDOR.C. FURNITURE IS TO BE PROCURED UNDER A SEPERATE CONTRACT.

© 20

17 M

OODY

•NOL

AN IN

C.PR

INT

DATE

:FI

LE IN

FO:

DRAWING TITLE:

FOR

DRAWN BY: CHECKED BY:

PROGRESS DRAWING NOT FOR

CONSTRUCTION

300 SPRUCE STREETSUITE 300COLUMBUS, OHIO 43215

PHONE: (614) 461-4664FAX: (614) 280-8881

5/13/ 2

019 1

0:34:3

9 AM

C:\$$

Loca

l Rev

it Pro

jects \

2017

Pro

jects\

1808

8.03 C

OTA

33 N

Hig h

1st a

nd 7t

h Floo

r Imp

rove

m ents

_dmi

l ler@

mood

ynola

n.co m

.rvt

18088.03

5-3-19

CONSTRUCTION DOCUMENTS

A901

Author Checker

FF&E

COTA DOWNTOWNADMINISTRATIVE OFFICERENOVATION

COTA

33 N. HIGH ST,COLUMBUS OH 43215

3/16" = 1'-0"SEVENTH FLOOR FF&E1

3/16" = 1'-0"LOBBY FF&E2 3/16" = 1'-0"

SECOND FLOOR FFE3

CURTIS J. MOODY, LIC. #7066EXP. DATE: 12/31/2019

# DATE CHANGE DESCRIPTION

LIST OF EQUIPMENT PROVIDED BY OWNER REMARKS(TO BE INSTALLED BY CONTRACTOR)

LOBBYTVM (LOBBY)TVM (VESTIBULE)KIOSK (SINGLE SIDED)KIOSK (DOUBLE SIDED)VIDEO WALLMONITORSCAMERASTV'S (LOBBY) INCLUDES REAL TIME DISPLAYTV'S (VESTIBULE)

BOARD ROOMPROJECTOR REINSTALL EXISTING OR PROVIDE NEW

2ND FLOORCAMERASTABLETS FOR LIBRARY USE

7TH FLOORCISCO CONFERENCE SYSTEM (LARGE CONF.) INCLUDES TVCISCO CONFERENCE SYSTEM (SMALL CONF.) INCLUDES TVTV'S KITCHEN AND OPEN OFFICE AREANETWORK CLOSET HARDWARE/ ACCESS POINTS